This product is intended to be supplied by a Listed Direct Plug-In Power Unit marked
“Class 2” or Listed Adapter marked “L.P.S.” (or “Limited Power Source”) and rated
output DC 12V, 0.415A minimum or AC 24V, 60Hz, 0.415A minimum.
3.10 NR ------------------------------------------------------------------------------ 13
3.11 CAMERA ID -------------------------------------------------------------------- 13
3.12 LANGUAGE --------------------------------------------------------------------- 13
3.13 CAMERA RESET ---------------------------------------------------------------- 13
3.14 SAVE ALL----------------------------------------------------------------------- 13
2
INTRODUCTION
1. Introduction
The dome camera is ideal for indoor installation in commercial and residential
environment. With 3-axis mount support, it provides exible installation on a ceiling
or wall even at an angle.
1.1 Before You Begin
Please read this manual carefully before you install the dome camera. Keep this
guide for future reference.
1.2 Dimensions
84mm
112mm
97mm
3
INTRODUCTION
1.3 Names of Camera Parts
Figure 1-1 Camera parts
1. Conduit hole used for surface run power/video connector
2. Bottom case
3. Camera housing
4. Dome cover
5. IR board
a. AC 24V / DC 12V power input connector (red +, black -)
b. Video output connector
Note:See Figure 2-3 for camera board controls.
a
b
1.4 Routine Maintenance
The dome cover is an optical part. Use a soft, dry cloth to remove any ngerprints
•
or dust.
Clean the camera housing with a soft, dry cloth. For more stubborn stains, use a
•
cloth dampened with a small quantity of neutral detergent, then wipe dry.
Caution: Do not use volatile solvents such as alcohol, benzene or thinners to avoid
damaging the surface nish.
4
INSTALLATION
2. Installation
2.1 Disassembling the Camera
Before you mount and adjust the camera, follow these steps to disassemble the
camera.
1. Insert a coin or at tool to the side hole and twist to remove the dome cover.
2. Remove the dome cover (#2).
1. Bottom case
2. Dome cover
Figure 2-1 Disassemble the camera
5
INSTALLATION
2.2 Connecting the wiring
Refer to Figure 1-1 to connect the video connect output connector (#b) and 24
VAC/12 VDC power connector (#a).
Caution:For DC power supply use, make sure the polarity is correct to avoid
malfunction and / or camera damage.
2.3 Mounting the Camera
1. Attach the mounting template to the wall or ceiling.
2. Drill two holes, then insert the screw anchors (#1) into the holes.
3. Secure the bottom case to the wall or ceiling with the TP4 x 15 mm tapping
screws supplied (#2).
4. To prevent the camera from falling off, ensures it is connected to a firm place
(ceiling slab or channel) using a Safety Wire (fall prevention wire#3 is not
supplied).
Note:Depending on the material of your mounting surface, you may require different
screws and anchors than those supplied.
③
Safety Wire (fall prevention
wire#3 is not supplied).
①
②
Please tighten a safety wire
using plastic band on a firm
place as photo.
Safety Wire
Plastic Band
1. Screw anchors (x2), supplied
2. TP4 x 15 tapping screws (x2),
supplied
3. Safety Wire(fall prevention
wire, not supplied)
Figure 2-2 Camera installation
6
INSTALLATION
2.4 Optional Camera Settings
Refer to Figure 2-3 to locate the OSD joystick control on the camera board. Use the
joystick to access the OSD menu and congure the camera settings as required.
To use the OSD joystick control:
Press the OSD joystick control straight down to enter the Main menu or a selected
•
item.
Move the OSD joystick control UP, DOWN, LEFT and RIGHT to navigate through
•
menus and options.
For further information on OSD settings, refere to the “3. OSD Settings” section.
1. Monitor out
2. OSD Joystick Control
3. Camera mounting holes
Figure 2-3 Camera adjustment controls
7
INSTALLATION
2.5 Adjusting the Camera Position
The dome camera has three axes for positioning the camera. While monitoring the
picture on the monitor, adjust the camera position as follows:
HorizontalAdjustment Rotate 3D assembly in the base. Do not turn assembly
more than 360° as this may cause the internal cables to twist and disconnect or
break. Before making horizontal adjustment, please adjust vertical adjustment to 90
degree (vertical) rst.
VerticalAdjustment After loosening the screw on the bracket, position the camera
as desired, then tighten the screw back to the bracket.
HorizontalRotationFor wall mount and tilted ceilings, rotate the lens base
(maximum 360°) until you are satised with the eld of view.
1. Rotate 3D assembly in base for
horizontal adjustment
2. Tilt adjustment bracket and screw
for vertical adjustment
3. Axis ring for horizontal rotation
for wall mount and tilted ceilings
Figure 2-4 Camera adjustment
2.6 Adjusting the Lens
1. Loosen the focus lever counter-clockwise a little, then adjust the focus for
optimum picture sharpness.
2. Loosen the zoom lever counter-clockwise a little, then rotate the zoom lever and
determine the image view.
3. Re-tighten the zoom lever and focus lever after adjustment.
Note:It is important that you lock the zoom and focus levers after making
adjustments. This will avoid the positions moving (for example, from temperature
changes or vibrations).
8
INSTALLATION
2.7 Completing the Installation
Once all adjustments are done, attach and secure the camera housing:
1. Use a soft, lint-free cloth to wipe the dome cover clean and remove ngerprints.
2. Assemble the dome cover (#2) and the bottom case (#1).
Figure 2-5 Completing the installation
9
OSD SETTINGS
3. OSD Settings
Use the OSD menu to set up the camera for optimum performance.
LENS AUTO
SHUTTER/AGC AUTO
WHITE BAL ATW
BACKLIGHT OFF
PICT ADJUST
ATR OFF
MOTION DET OFF
NEXT
EXIT SAVE ALL
Figure 3-1 OSD Main Menu
3.1 Lens
The LENS settings allows you to congure Lens and brightness. Options are AUTO (Auto
Iris lens) and MANUAL. The default setting is AUTO.
In the AUTO submenu, you can set the MODE as OPEN, CLOSE or AUTO. Then select
SPEED to adjust the DC Iris Lens convergence speed.
TYPE DC
MODE OPEN
SPEED 046
PRIVACY OFF
DAY/NIGHT AUTO
NR
CAMERA ID OFF
SYNC INT
LANGUAGE ENGLISH
CAMERA RESET
BACK
EXIT SAVE ALL
3.2 SHUTTER/AGC
You can set the SHUTTER/AGC as AUTO or MANUAL. The default setting is AUTO.
WhenLENSissettoAUTO:It is recommended to set SHUTTER/AGC to AUTO
mode. In the AUTO submenu, adjust HIGH LUMINANCE MODE mode according to
your application:
AUTOIRISmode: Use this for normal condition application environments. The
•
IRIS level will be controlled by camera brightness.
SHUT+AUTOIRISmode: Use this for high light application environments. The
•
exposure will be controlled by AES or the DC Iris. The iris level will be controlled
by camera brightness.
HIGH LUMINANCE
MODE AUTO IRIS
BRIGHTNESS 024
LOW LUMINANCE
MODE AGC
BRIGHTNESS x0.25
10
OSD SETTINGS
If SHUTTER/AGC is set to MANUAL, the submenu is shown as below. The shutter
speed is a variable from 1/50(1/60)sec to 1/10000sec and the AGC is selectable
depending on your environment condition.
MODE SHUT+AGC
SHUTTER 1/50(1/60)
AGC 6.0
Recommended settings according to the application:
1. Auto Exposure by Iris Control:
Application: General Purpose, Indoor surveillance. This is default settings.
•
LENS: AUTO
•
SHUTTER/AGC: AUTO
•
HIGH LUMINANCE MODE: AUTO IRIS
•
2. Auto Exposure by AES rst, then by IRIS Control:
Application: Outdoor, Trafc surveillance
•
LENS: AUTO
•
SHUTTER/AGC: AUTO
•
HIGH LUMINANCE MODE: SHUT AUTO IRIS
•
3. Auto Exposure by Iris Control with xed Shutter Speed:
LENS: AUTO
•
SHUTTER/AGC: MANUAL
•
SHUTTER 1/50 (1/60) ~ 10000
•
After this, the following are set
SHUTTER/AGC: AUTO
•
HIGH LUMINANCE MODE: SHUT+AUTOIRIS
•
3.3 WHITE BAL
WHITE BALANCE controls color on the screen. Options include ATW (Auto White
Balance), PUSH, PUSH LOCK, USER1, USER2, ANTI CR (Anti Color Rolling
Suppression) and MANUAL. The default is ATW.
ATW: Select ATW when the scene illumination varies between indoor scenes and
MANUAL: You can manually adjust the LEVEL from 15 to 69.
•
USER1/USER2: You can adjust blue setting (B-GAIN) and red setting (R-GAIN)
•
value from 0 to 255.
11
OSD SETTINGS
PUSH: When selected in the appropriate position, the whole area will perform
•
white balance.
PUSHLOCK: When selected in the appropriate position, WHITE BALANCE will
•
perform once.
3.4 BACKLIGHT
Set Backlight compensation function. It controls the light level to overcome
sever backlight conditions. Available options include OFF, BLC or HLC (Highlight
Compensation) mode. The default is OFF.
If HLC is selected, HLC is activated automatically when the camera detects highluminance.
3.5 PICT ADJUST
PICTURE ADJUST allows you to adjust picture settings for optimal image. In the PICT
ADJUST submenu, you can adjust BRIGHTNESS, CONTRAST, SHARPNESS, HUE and
GAIN value. In addition, you can set MIRROR to ON to reect the image.
MIRROR OFF
BRIGHTNESS 000
CONTRAST 128
SHARPNESS 128
HUE 128
GAIN 128
3.6 ATR*
Set ATR (Adaptive Tone-curve Reproduction) function. You can select ON or OFF. The
default is OFF. If selecting ON, you will enter the ATR submenu, where you can set
LUMINACE and CONTRAST to optimize by image.
LUMINANCE LOW
CONTRAST LOW
*Also known as Wide Dynamic Range. This function expands the video dynamic range
of the camera and improves visibility of images even in high contrast environments.
3.7 MOTION DET
MOTION DET allows to detect moving objects on the screen. The default is OFF. If
selecting ON, you will enter the MOTION DET submenu. You can set up to 4 motion
areas to detect moving objectives and adjust the motion detection sensitivity from 0
to 127.
3.8 PRIVACY
PRIVACY function mask up to 8 privacy areas on the screen from video monitoring.
The default setting is OFF. If selecting ON, you will enter the PRIVACY submenu. You
can congure up to 8 privacy areas and set color and transparency of the privacy
zones. In addition, you can enable MOSAIC function for the privacy zone.
12
OSD SETTINGS
Note: If you enable MOTION DET function, then PRIVACY function will support 4
zones only.
REA SEL 1/8
TOP 000
BOTTOM 000
LEFT 000
RIGHT 000
COLOR 1
TRANSP 0.00
MOSAIC OFF
3.9 DAY/NIGHT
The camera will automatically switch to B/W mode when the illumination is under a
certain threshold. There is no need to adjust this setting.
Under B/W mode, you can set BURST to be ON or OFF.
3.10 NR
NR allows you to congure the DNR (Digital Noise Reduction) settings to reduce noise
on the screen. In the NR submenu, you can enable the NR MODE to the Y (BRIGHT) /
C (COLOR), C LEVEL or Y LEVEL mode. According to your NR mode, you can adjust Y
LEVEL or C LEVEL as required.
NR MODE Y/C
Y LEVEL 000
C LEVEL 000
Note: When the Y/C Level is higher, the noise in dark areas become lessened. Also,
resolution will become lower. When it is lower, there are more noise in dark areas.
3.11 CAMERA ID
CAMERA ID allow you to specify camera ID. Options are OFF (default) and ON. In the
ON submenu, you can add a camera title up to 26 characters with 2 lines and also
select where the title appears on the monitor screen.
3.12 LANGUAGE
OSD supports 8 multiple languages. Options include ENGLISH (default), JAPANESE,
GERMAN, FRENCH, RUSSIAN, PORTUGUESE, SPANISH and SIMPLIFIED CHINESE.
3.13 CAMERA RESET
To restore factory defaults, select CAMERA RESET and then press the joystick control.
3.14 SAVE ALL
SAVE ALL item allows you to save all settings and exit the OSD menu.