JVC SP-THM45C User Manual
DVD DIGITAL CINEMA SYSTEM
TH-M45
Consists of XV-THM45, SP-PWM45, SP-THM45C, SP-THM45F and SP-THM45S
INSTRUCTIONS
LVT1024-009B
[A]
Warnings, Cautions and Others
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
CAUTION — F button!
(XV-THM45)
Disconnect the mains plug to shut the power off completely (the
STANDBY lamp goes off).
The F button in any position does not disconnect the mains line.
• When the system is on standby, the STANDBY lamp lights red.
• When the system is turned on, the STANDBY lamp goes off.
The power can be remote controlled.
CAUTION (SP-PWM45)
The power supply to the subwoofer is linked to the center unit. The
POWER ON lamp on the subwoofer lights green when the power is turned
on.
IMPORTANT FOR LASER PRODUCTS
REPRODUCTION OF LABELS
CLASSIFICATION LABEL, PLACED ON EXTERIOR SURFACE
A
WARNING LABEL, PLACED INSIDE THE UNIT
2
1. CLASS 1 LASER PRODUCT
2.
CAUTION:
failed or defeated. Avoid direct exposure to beam.
3.
CAUTION:
inside the Unit; leave all servicing to qualified service personnel.
I
Visible and invisible laser radiation when open and interlock
Do not open the top cover. There are no user serviceable parts
CAUTION
• Do not block the ventilation openings or holes.
(If the ventilation openings or holes are blocked by a newspaper or
cloth, etc., the heat may not be able to get out.)
• Do not place any naked flame sources, such as lighted candles, on the
apparatus.
• When discarding batteries, environmental problems must be considered
and local rules or laws governing the disposal of these batteries must be
followed strictly.
• Do not expose this apparatus to rain, moisture, dripping or splashing and
that no objects filled with liquids, such as vases, shall be placed on the
apparatus.
G-1
Warnings, Cautions and Others
Caution: Proper Ventilation
To avoid risk of electric shock and fire and to protect from damage, place the apparatus on a level surface. The minimal clearances are
shown below:
Wall or
obstructions
Wall or
obstructions
No obstructions
1 cm 1 cm
XV-THM45
10 cm
20 cm
SP-PWM45
15 cm15 cm
Front
No obstructions
Front
No obstructions
Wall or obstructions
XV-THM45
10 cm
Wall or obstructions
SP-PWM45
15 cm
G-2
Table of contents
Introduction...................................... 2
Notes on handling..................................................................2
Supplied accessories .............................................................2
English
About discs ......................................3
Playable disc types ................................................................3
Disc structure ........................................................................4
Playback Control function (PBC) — VCD and SVCD only ......4
Names of parts and controls ...........5
Getting started................................. 8
Connections...........................................................................8
Using the remote control .....................................................14
Basic operations ............................ 17
Turning the system on/off....................................................17
Selecting the source to play.................................................18
Adjusting the volume ...........................................................18
Listening with headphones ..................................................18
Turning off the sound temporarily .......................................18
Adjusting the brightness ......................................................18
Using the Sleep Timer..........................................................19
Adjusting the output level of the subwoofer.........................19
Adjusting the bass/treble sound...........................................19
Changing the decode mode .................................................20
Changing the scan mode .....................................................20
Playback......................................... 21
Basic playback .....................................................................21
Playback features.................................................................23
Tuner operations............................ 25
Setting the AM tuner interval spacing ..................................25
Manual tuning......................................................................25
Preset tuning .......................................................................25
Selecting the FM reception mode.........................................26
Reducing the noise of AM broadcast ...................................26
Creating realistic sound fields ......27
Using the surround mode ....................................................29
Adjusting the sound.............................................................30
Advanced operations ..................... 31
Using the on-screen bar ......................................................31
Playing from a specified position on a disc..........................32
Using the MP3 control display.............................................34
Using the JPEG control display............................................35
Selecting a view angle of DVD .............................................36
Selecting the subtitle/audio languages.................................37
Special picture playback ......................................................39
Program Playback................................................................41
Random Playback................................................................42
Repeat Playback ..................................................................42
Setting DVD preferences ...............44
Using the choice menus ......................................................44
Menu description.................................................................46
Parental Lock.......................................................................49
System setting ............................... 52
AV COMPU LINK remote control
system ............................................53
References ..................................... 54
Maintenance ........................................................................54
Trouble shooting..................................................................54
Glossary...............................................................................57
Index....................................................................................58
Specifications ......................................................................59
1
Introduction
Notes on handling
7
Important cautions
Installation of the system
• Select a place which is level, dry and neither too hot nor too cold;
between 5°C and 35°C (41°F and 95°F).
• Leave sufficient distance between the system and the TV.
• Do not use the system in a place subject to vibration.
Power cord
• Do not handle the power cord with wet hands!
• A small amount of power (1.6 watts) is always consumed while
the power cord is connected to the wall outlet (center unit only).
• When unplugging the power cord from the wall outlet, always
pull on the plug, not the power cord.
To prevent malfunctions of the system
• There are no user-serviceable parts inside. If anything goes
wrong, unplug the power cord and consult your dealer.
• Do not insert any metallic object into the system.
• Do not use any non-standard shape disc (like a heart, flower or
credit card, etc.) available on the market, because it may damage
the system.
• Do not use a disc with tape, stickers, or paste on it, because it
may damage the system.
7
Safety precautions
Avoid moisture, water and dust
Do not place the system in moist or dusty places.
Avoid high temperatures
Do not expose the system to direct sunlight and do not place it near
a heating device.
When you are away
When away on travel or for other reasons for an extended period of
time, disconnect the power cord plug from the wall outlet.
Do not block the vents
Blocking the vents may damage the system.
Care of the cabinet
When cleaning the system, use a soft cloth and follow the relevant
instructions on the use of chemically-coated cloths. Do not use
benzene, thinner or other organic solvents including disinfectants.
These may cause deformation or discoloring.
If water gets inside the system
Turn the system off and disconnect the power cord plug from the
wall outlet, then call the store where you made your purchase.
Using the system in this condition may cause fire or electrical
shock.
Label sticker
Sticker
Paste
Note about copyright laws
Check the copyright laws in your country before recording from
DVDs, Super Video CDs (SVCDs), Video CDs (VCDs) and Audio
CDs. Recording of copyrighted material may infringe copyright
laws.
Note about copyguard system
DVDs are protected by copyguard system. When you connect the
system to your VCR directly, the copyguard system activates and
the picture may not be played back correctly.
Supplied accessories
Check to be sure you have all of the supplied accessories.
The number in parentheses is the quantity of the pieces supplied.
If anything is missing, contact your dealer immediately.
• Remote control (1)
• Batteries (2)
• FM antenna (1)
• AM loop antenna (1)
•Power cord (1)
• System cord (1)
• Composite video cord (1)
• Speaker cords
5 m: For satellite (front left/right) and center speakers (3)
10 m: For satellite speakers (surround left/right) (2)
(Length of speaker cords is approximate.)
This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection
technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only
unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
2
About discs
Playable disc types
This system has been designed to play back the following discs:
English
DVD Video (DVD), Video CD (VCD), Super Video CD (SVCD),
Audio CD, CD-R and CD-RW.
• This system can also play back MP3 and JPEG files recorded on
CD-Rs and CD-RWs. (Apg. 21)
• This system can also play back finalized DVD-Rs recorded in
DVD VIDEO format. However, some discs may not be played
back because of their disc characteristics or recording conditions.
Discs you can play:
Disc
Type
DVD
VCD
SVCD
Audio CD — —
CD-R — —
CD-RW — —
*
Note on Region Code
DVD players and DVDs have their own Region Code numbers. This
system can only play back DVDs recorded with the color system of
NTSC or PAL whose Region Code number includes “4”.
Examples:
If a DVD with an improper Region Code number is loaded,
“REGION CODE ERROR!” appears on the TV screen and playback
cannot start.
• The following discs cannot be played back:
DVD Audio, DVD-ROM, DVD-RAM, DVD-RW, CD-ROM,
CD-I (CD-I Ready), Photo CD, etc.
Playing back these discs will generate noise and damage the
speakers.
• On some DVDs, Video CDs or SVCDs, their actual
operation may be different from what is explained in this
manual. This is due to the disc programming and disc
structure, not a malfunction of this system.
Notes on CD-R and CD-RW
• User-edited CD-Rs (Recordable) and CD-RWs (Rewritable) can
be played back only if they are already “finalized”.
• This system can play back CD-Rs or CD-RWs recorded on a
personal computer if they have been recorded in the audio CD
format.
This system can also play back CD-Rs or CD-RWs if MP3 files
or JPEG files are recorded on them.
However, some discs may not be played back because of their
disc characteristics, recording conditions, or damage or stain on
them.
Mark (Logo)
Video
Format
NTSC/
PA L
NTSC/
PA L
NTSC/
PA L
Region
Code
Number
4/ALL
—
—
Especially, the configuration and characteristics of an MP3 disc
or a JPEG disc are determined by the writing (encoding) software
and hardware used for recording. Therefore, due to the software
and hardware used, the following symptoms may occur:
Some discs may not be played back.
•
Some tracks on an MP3 disc may be skipped or may not be
•
played back normally.
Some files on a JPEG disc may be played back distortedly.
•
• Before playing back CD-Rs or CD-RWs, read their instructions
or cautions carefully.
• CD-RWs may require a longer readout time. This is caused by
the fact that the reflectance of CD-RWs is lower than that of
regular CDs.
About MP3 discs
*
MP3 is an abbreviation for Motion Picture Experts Group 1 (or
MPEG-1) Audio Layer 3. MP3 is simply a compressed data file
format. By using MP3 format, one CD-R or CD-RW can contain 10
times as much data as one regular CD.
About JPEG discs
A still-picture data compression system proposed by the Joint
Photographic Expert Group, which features small decrease in
image quality in spite of its high compression ratio.
Notes on MP3/JPEG discs
• MP3/JPEG discs (either CD-R or CD-RW) require a longer
readout time. (It differs due to the complexity of the directory/file
configuration.)
• When making an MP3/JPEG disc, select ISO 9660 Level 1 or
Level 2 for the disc format.
• This system supports “multi-session” discs (up to 5 sessions).
• This system cannot play “packet write” discs.
• The system can only play MP3/JPEG files with the following file
extensions;
MP3: “.MP3”, “.Mp3”, “.mP3” and “.mp3”
JPEG: “.jpg”, “.jpeg”, “.JPG”, “.JPEG” and any uppercase and
lowercase combination (such as “.Jpg”)
• If both MP3 files and JPEG files are recorded on a disc, set the
MP3/JPEG setting in the PICTURE menu to the appropriate
setting for the data to be read (“MP3” or “JPEG”). (Apg. 47)
• Some MP3/JPEG discs may not be played back because of their
disc characteristics or recording conditions.
Notes on MP3 discs only
• ID3* tags cannot be shown on the display.
* An MP3 file can contain file information called an “ID3 Tag”
where its album name, performer, track title, etc. are recorded.
There are two versions, ID3v1 (ID3 Tag version 1) and ID3v2
(ID3 Tag version 2).
• We recommend to record each piece of material (song) at a
sample rate of 44.1 kHz and at a data transfer rate of 128 kbps.
• Some tracks on an MP3 disc may be skipped or may not be
played back normally.
Notes on JPEG discs only
• We recommend to record a file at 640 x 480 resolution. (If a file
has been recorded at a resolution of more than 640 x 480, it will
take a longer time to be displayed.)
• This system can only play baseline JPEG files*. Progressive
JPEG files* or lossless JPEG files* cannot be played.
* Baseline JPEG format: Used for digital cameras, web, etc.
Progressive JPEG format:Used for web.
Lossless JPEG format: An old type and rarely used now.
• Some files on a JPEG disc may be played back distortedly.
3
About discs
NOTE
Submenu
Menu screen
A: Moving picture
B: Still picture
Press RETURN.
Press RETURN.
Press
RETURN.
IMPORTANT
Before playing a disc, make sure of the following;
• Check the connection with the TV.
• Turn on your TV and select the correct input mode on the TV to view
the pictures or on-screen information on the TV screen.
• For DVD playback, you can change the initial setting to your
preference. (Apg. 44 – 51)
If B appears on the TV screen when pressing a button;
The disc cannot accept the operation you have tried to do, or the
information required for that operation is not recorded on the
disc.
NOTICE:
be accepted.
In some cases, without showing B, operations will not
Disc structure
DVD
A DVD consists of “titles” and each title may be divided into
“chapters”.
For example, if a DVD contains movies, each movie may have its
own title number and may be further divided into chapters.
Title 1 Title 2
Chapter 1 Chapter 2 Chapter 3 Chapter 1 Chapter 2
Playback Control function
(PBC) — VCD and SVCD
only
The Playback Control function allows you to enjoy menu-driven
operation and high-resolution still images which have a resolution
four times greater than moving pictures.
High-resolution still image display
You can display high-quality images which are four times clearer
than moving pictures.
Menu-driven playback
A selection menu is displayed when you start playing a Video CD
or SVCD with the Playback Control feature. The selection menu
shows a list of numbers for selection. Some discs may show
moving pictures or a divided screen.
You can interact with the screen using a menu display to select and
play an entry.
See example illustration below about basic features of menu-driven
playback (for details about the operation through the menu, also see
page 33).
Video CD/SVCD/Audio CD
A Video CD, SVCD, Audio CD consists of “tracks”.
In general, each track has its own track number. (On some discs,
each track may also be further divided by indexes.)
Track 1Track 2Track 3Track 4Track 5
MP3 discs
On an MP3 disc, each song is recorded as a track (file). Tracks are
usually grouped into a group (folder). Groups can also include
other groups, creating hierarchical group layers. This system can
recognize up to 150 tracks per group and up to 99 groups per disc.
• If there is any type of file other than MP3 files in a group
(folder), those files are also counted in the total number of 150.
Group 1 Group 2
Track 1 Track 2 Group 3 Group 4 Group 5
JPEG discs
On a JPEG disc, each still picture is recorded as a file. Files are
usually grouped into a group (folder). Groups can also include
other groups, creating hierarchical folder layers. This system can
recognize up to 150 files per group and up to 99 groups per disc.
• If there is any type of file other than JPEG files in a group
(folder), those files are also counted in the total number of 150.
Group 1 Group 2
• When operating a Video CD or SVCD using the menu, some
functions such as Repeat Playback may not work.
File 1 File 2 Group 3 Group 4 Group 5
4
Names of parts and controls
Front panel (center unit)
English
Standby lamp (STANDBY) Apg. 17
A
Standby-on button (
B
Stop button (
C
Play button (
D
Pause button (
E
Reverse skip button (
F
Forward skip button (
G
Source button (SOURCE) Apg. 18
H
) Apg. 21
7
) Apg. 21
3
) Apg. 21
8
STANDBY/ON) Apg. 17
F
) Apg. 24
4
) Apg. 24
¢
Rear panel (center unit)
Volume control (VOLUME) Apg. 18
I
Headphones jack (PHONES) Apg. 18
J
Disc trays Apg. 21
K
Illumination lamp Apg. 18
L
Remote sensor Apg. 14
M
Display window Apg.6,22
N
Open/close buttons (
O
Disc buttons (DISC 1-5) Apg. 21
P
) Apg. 21
0
System cord connector Apg. 10
A
Audio input jacks (AUDIO IN (VCR)) Apg. 12
B
Digital input jack
C
(DIGITAL IN) Apg. 12
Antenna terminals (ANTENNA) Apg. 9
D
Video output jacks (VIDEO OUT) Apg. 8
E
VIDEO, S-VIDEO
5
Video input jacks (VCR IN) Apg. 12
F
VIDEO, S-VIDEO
Video output jacks (VIDEO OUT) Apg. 8
G
COMPONENT (Y, P
Video output signal switch
H
(VIDEO OUT SELECT) Apg. 8
PAL , N TS C
AV COMPU LINK-III jacks Apg. 53
I
AC IN socket Apg. 13
J
Ó
B,PR
)
Names of parts and controls
Display window (center unit)
A Disc indicators A pg. 23
B MP3 indicator A pg. 22
C Channel indicator (CH) A pg. 26
D Main display A pg. 22
E Stereo indicator (ST) A pg. 25
F Tuning indicator (TUNED) A pg. 25
G Auto muting indicator (AUTO MUTING) A pg. 26
•
H
Source signal indicators (abcdghi )
A pg. 28
•
Subwoofer indicator ( ) A pg. 28
•
Sound reproducing speaker indicator ( ) A pg. 28
Powered subwoofer
•
I
Dolby Pro Logic II indicator (GPLII) A pg. 27
•
Linear PCM indicator (LPCM) A pg. 28
•
Digital signal format indicators A pg. 28
Dolby Digital (G
J Surround indicator (SURROUND) A pg. 29
K DSP indicator A pg.27–29
L Progressive mode indicator (PROGRESSIVE) A pg. 20
M Resume indicator (RESUME) A pg. 22
N Repeat mode indicators A pg. 42
DIGITAL), DTS (C)
Rear
A System cord connector A pg. 10
B Front speaker terminals (FRONT SPEAKERS) A pg. 11
C Center speaker terminals (CENTER SPEAKER) A pg. 11
D Surround speaker terminals (SURROUND SPEAKERS) A pg. 11
E Power cord A pg. 13
F Power lamp (POWER ON) A pg. 17
Front
6
Names of parts and controls
Remote control
English
NOTE
• To use buttons I –
and g – p, slide
W
down the remote
control cover.
A Remote control mode selector A pg.15–52
AUDIO, TV, VCR/DBS
B Muting button (MUTING) A pg. 18
C Disc buttons (DISC 1-5) A pg. 21
D TV volume buttons (TV VOL +/–) A pg. 15
E Operating buttons
•
Play button (3) A pg. 22
•
Forward/reverse skip buttons (¢/4) A pg. 24
•
Fast-forward/reverse playback buttons (¡/1) A pg. 24
•
Stop button (7) A pg. 21
•
Pause button (8) A pg. 21
•
Tuning buttons (TUNINGª, TUNING·) A pg. 25
•
Memory button (MEMORY) A pg. 26
•
FM reception/Beat Cut mode button (FM MODE) A pg. 26
F Top menu button (TOP MENU) A pg. 32
•
G
Cursor buttons (3/2///5) A pg. 32
•
Enter button (ENTER) A pg. 15
•
H
One Touch Replay button ( ) A pg. 23
•
Record button (REC) A pg. 16
I Audio button (AUDIO) A pg. 37, 38
J Subtitle button (SUBTITLE) A pg. 37
•
K
VFP setting button A pg. 40
•
Progressive mode button (PROGRESSIVE) A pg. 20
L Choice menu button (CHOICE) A pg. 44
M Setting button (SETTING) A pg. 52
N Title/group button (TITLE/GROUP) A pg. 33
O Repeat button (REPEAT) A pg. 42
P A-B repeat button (A-B REPEAT) A pg. 43
Q Sleep button (SLEEP) A pg. 19
R Dimmer button (DIMMER) A pg. 18
S Surround buttons (SURROUND)
Mode (MODE), On/Off (ON/OFF) A pg. 29
T Effect button (EFFECT) A pg. 30
U Test tone button (TEST) A pg. 30
V Subwoofer adjustment buttons (S.WFR +/–) A pg. 19
W Center speaker adjustment buttons (CENTER +/–) A pg. 30
X Standby-on button (
Y Standby-on button (F
Z Standby-on button (F
F
AUDIO) A pg. 17
VCR/DBS) A pg. 15
TV) A pg. 15
a Source selecting buttons A pg. 18
DVD, FM/AM, DBS, VCR
b TV/Video mode button (TV/VIDEO) A pg. 15
c Channel buttons (CHANNEL +/–) A pg. 15
d Volume buttons (AUDIO VOL +/–) A pg. 18
e Menu button (MENU) A pg. 32
f On-screen button (ON SCREEN) A pg. 31
•
G
Number buttons A pg. 15, 24, 33
•
TV returning button (TV RETURN) A pg. 15
h Return button (RETURN) A pg. 4, 33
i Angle button (ANGLE) A pg. 36
j Decode mode button (DECODE) A pg. 20
k Zoom button (ZOOM) A pg. 39
l Cancel button (CANCEL) A pg. 41
m Display window button (FL DISPLAY) A pg. 22
n Treble adjustment buttons (TREBLE +/–) A pg. 19
o Bass adjustment buttons (BASS +/–) A pg. 19
p Surround speaker adjustment buttons (SURR) A pg. 30
Left (L +/–), Right (R +/–)
7
Getting started
Connections
• Do not connect the AC power cord until all other connections have been made.
• Since different components often have different terminal names, carefully read the instructions supplied with the components you are going
to connect.
Connecting a TV
To view pictures and on-screen displays, connect the TV to the center unit.
• You can get better picture quality in the order — Component video > S-video > Composite video.
• Distortion of picture may occur when connecting to the TV via a VCR, or to a TV with a built-in VCR.
• You need to set “MONITOR TYPE” in the PICTURE menu correctly according to the aspect ratio of your TV. (Apg. 47)
%
To connect a TV through the component video input jacks
If your TV has component video input jacks, connect them using a component video cord (not supplied) to view a high quality picture.
• Connect “Y” to “Y”, “P
• If your TV supports progressive video input, you can enjoy a high quality picture by setting the progressive scan mode to active. (Apg. 20)
” to “PB”, “PR” to “PR” correctly.
B
Center unit
Green
To component video input
TV
Component video cord
(not supplied)
NOTE
• If the component video input jacks of your TV are of the BNC type, use a plug adapter (not supplied) to convert the pin plugs to BNC plugs.
• The component video signals can be output only when you select “DVD” as the source to play. (Apg. 18)
%
To connect a TV through the composite or S-video jacks
Connect the TV using the composite video cord (supplied) or an S-video cord (not supplied).
If your TV has an S-video (Y/C-separation) jack, you can get better picture quality than by using composite video connection.
• Connect the S-video cord by matching the / mark on the plug to the one on the rear of the center unit.
To composite
video input
TV
To S-video input S-video cord
Composite video cord
(not supplied)
Blue
(supplied)
or
Red
VIDEO OUT SELECT switch
(see below.)
Center unit
VIDEO OUT SELECT switch
(see below.)
%
Selecting the color system
The center unit is compatible with the PAL and NTSC systems. Set the VIDEO OUT SELECT switch on the rear panel in standby mode to
match the color system of your TV. Make sure that the color system of a DVD, Video CD, or SVCD disc labeled on the package matches your
TV.
• If you use a multi-system TV, by setting “MONITOR TYPE” in the PICTURE menu to an appropriate “MULTI” option, the system outputs
a video signal by the same format recorded on the disc (i.e. if you play an NTSC disc, the system outputs a signal by the NTSC format)
regardless of the VIDEO OUT SELECT switch setting. (Apg. 47)
8
Getting started
NOTE
Outdoor single vinyl-covered wire antenna
(not supplied)
AM loop antenna
Extend the supplied FM
antenna horizontally.
Center unit
Outdoor FM antenna
(not supplied)
Outdoor FM antenna cord
(not supplied)
Connecting the FM and AM antennas
Make sure the antenna conductors do not touch any other terminals,
connecting cords and power cords. This could cause poor reception.
English
%
AM loop antenna
Setting up supplied AM loop antenna
Attach the AM loop to its base by snapping the tabs on the loop into
the slot on the base.
If the antenna cord is covered with the insulation
coat, twist and pull the insulation coat off and
remove.
Connecting AM loop antenna
Center unit
If reception is poor
Connect an outdoor single vinyl-covered wire antenna (not
supplied) to the AM EXT terminal. (Keep the AM loop antenna
connected.)
• Twist together both wires.
%
FM antenna
Connecting supplied FM antenna
Press and hold down the terminal
clamp.
Insert the antenna cord.
Release finger from the clamp.
• Turn the loop antenna until you have the best reception.
If reception is poor
Connect an outdoor FM antenna with standard type (75 C coaxial)
connector.
• Disconnect the supplied FM antenna before attaching a 75 C coaxial
connector (the kind with a round wire going to an outdoor antenna).
• We recommend that you use coaxial cable for the FM antenna as it is
well-shielded against interference.
9
Getting started
Front rightFront left
Center
speaker
Powered
subwoofer
Surround
left
Surround
right
Connecting the powered subwoofer
Connect the supplied powered subwoofer (SP-PWM45) using the system cord (supplied).
• Connect the system cord by matching the # marks on the plugs to the ones on the center unit and powered subwoofer.
System cord
(supplied)
Ensure that the # mark on
the plug faces down.
Center unit
Powered
subwoofer
Connecting the satellite speakers
%
Speaker layout
When positioning the speakers, to obtain the best possible sound
from this system you need to place all satellite speakers at the same
distance from the listening position with the front of each speaker
facing toward the listener.
When you cannot place them at the same distance from the
listening position, you can make adjustment so that
speakers operate as if they are placed at the best position.
(AAAA pg. 48)
• Normally place the powered subwoofer in front of you. (Since
bass sound is non-directional, you do not need to place it at the
same distance as the other speakers.)
NOTE
• Although the satellite speakers and the powered subwoofer are
magnetically shielded, the TV screen may appear mottled. In this
case, keep the distance between them to the TV to over 10 cm.
• For safety reasons, always ensure that there is sufficient space behind
the powered subwoofer.
• When you position the satellite speakers in a relatively high place,
such as the top of your bookshelf, place them on a flat and level
surface.
• Speaker grilles are not removable. Trying to remove them by force
may damage them.
10
Getting started
%
Connecting the satellite (front, center, surround) speakers
Be sure to identify each speaker
powered subwoofer.
English
CAUTION
• When you connect (larger) speakers other than the supplied ones, only use speakers with the same speaker impedance (SPEAKER IMPEDANCE)
as indicated by the speaker terminals on the rear of the powered subwoofer.
• DO NOT connect more than one speaker to one speaker terminal.
Before connecting the
speaker cords;
Twist and pull the
insulation coat off and
remove.
(SP-THM45C/SP-THM45F/SP-THM45S) and connect them to the corresponding terminals of the
Front speakers (SP-THM45F)
Press and hold
the clamp.
• Connect the white cords to the red (ª) terminals and black cords
to the black (·) terminals.
Insert the bare end of the
speaker cord into the
terminal.
Release the
clamp.
Center speaker
(SP-THM45C)
Surround speakers
(SP-THM45S)
CAUTION
When installing the satellite speakers on the wall;
• Be sure to have them installed on the wall by a qualified personnel.
DO NOT install the satellite speakers on the wall by yourself to avoid unexpected damage from their falling off the wall due to incorrect installation
or weakness in wall structure.
• Care must be taken in selecting a location for speaker installation on a wall. Injury to personnel or damage to equipment may result if the speakers
installed interfere with daily activities.
Powered
subwoofer
Black
Black
White
Red
11
Getting started
Connecting to an analog component
You can enjoy the sound of an analog component such as a VCR, TV, or Cassette recorder with this system. Use RCA pin plug cords (not
supplied) for connection.
Center unit
Red
White
S-video cord
(not supplied)
or
Composite video cord
(not supplied)
RCA pin plug cord
(not supplied)
AB C
VCR
NOTE
• The signals input to the VIDEO jack of the VCR IN jacks will be output only from the VIDEO jack of the VIDEO OUT jacks, not from the S-VIDEO
jack of the VIDEO OUT jacks.
A To composite video output
B To S-video output
C To audio output
C
C
TV Cassette recorder
Connecting to a digital component
You can enjoy the sound of a digital component such as a DBS (Direct Broadcast Satellite) tuner or MD recorder with this system. Use digital
optical cord (not supplied) for connection.
Before connecting a digital
optical cord, unplug the
protective plug.
Center unit
Digital optical cord
(not supplied)
To digital optical output
DBS tuner
NOTE
• Only digital audio signals can be input when selecting “DBS” as the source to play. (Apg. 18) When connecting a video component such as a DBS
tuner, operate this system to listen to the sound.
MD recorder
12
Getting started
Connecting the power cord
Make sure that all connections have been completed, before plugging in the power cords of the center unit and powered subwoofer.
English
Firmly insert the supplied power cord into the ÓAC IN socket on the rear of the center
1
unit.
Plug both power cords into AC outlets.
2
Center unit
Plug into AC outlets.
Power cord
(supplied)
Power cord
CAUTION
• Disconnect the power cord before cleaning or moving the system.
• Do not touch the power cord with wet hands.
• Do not pull on the power cord to unplug the cord. When unplugging the cord, always grasp and pull the plug so as not to damage the cord.
NOTE
• Keep power cords away from other connected cords. The power cords may cause noise or screen interference.
• Preset settings, such as preset stations and surround mode adjustment, may be erased in a few days in the following cases;
If you unplug the power cord of the center unit.
•
If a power failure occurs.
•
• The speakers will not produce any sound if the power cord of the powered subwoofer is removed from the AC outlet while the center unit is turned on.
In this case, press
then press
F
AUD IO
F
on the remote control or
AUD IO
or
STANDBY/ON
F
again.
STANDBY/ON
F
on the center unit to turn the power off, plug in the powered subwoofer,
Powered subwoofer
13
Getting started
Remote sensor
Using the remote control
The remote control makes it easy to use many of the system
functions from a distance of up to 7 m away.
• You can also use the remote control supplied for this system to
operate other manufacturers’ TVs (Apg. 15), VCRs (Apg. 16)
and DBS tuners/CATV converters (Apg. 15).
Putting batteries in the remote control
Before using the remote control, first put in the 2 supplied batteries.
Remove the battery
1
cover on the back of
the remote control.
Insert the batteries.
2
• Make sure to match polarity: (+) to
(+) and (–) to (–).
Operating the system from the remote
control
Aim the remote control directly at the remote sensor on the center
unit.
• To control other components, aim the remote control directly at
the remote sensor on each component. Refer also to their
instruction manuals.
• To operate the remote control properly, do not hide the remote
sensor by placing any obstructions in front of it.
Replace the cover.
3
If the range or effectiveness of the remote control decreases,
replace the batteries. Use two R6P (SUM-3)/AA (15F) type drycell batteries.
CAUTION
• Follow these precautions to avoid leaking or cracking batteries;
Use the correct type of batteries. Batteries that look similar may
•
differ in voltage.
Always replace both batteries at the same time.
•
Do not expose batteries to heat or flame.
•
14
Getting started
NOTE
IMPORTANT
English
Remote control
mode selector
(play button)
Number
buttons
Press number buttons (1-9, 0) to enter
4
the manufacturer’s code (2 digits).
Examples:
For a Hitachi TV: Press 1, then 0.
For a Toshiba TV:Press 0, then 8.
Manufacturer Code Manufacturer Code
JVC 01 Samsung 12
Hitachi 10 Sanyo 13
Magnavox 02 Sharp 06
Mitsubishi 03 Sony 07
Panasonic 04, 11 Toshiba 08
RCA 05 Zenith 09
Release FTV.
5
Try operating your TV by pressing
6
F
TV.
When your TV turns on or off, you have entered the correct
code.
If there is more than one code listed for corresponding brand,
try each one until you enter the correct one.
For TV operations
You can operate your TV using the remote control supplied with
this system.
• Refer also to the instruction manuals supplied with your TV.
7
To set the manufacturer’s code
You can operate a JVC TV without setting the remote control
signal.
Slide the remote control mode selector
1
to TV.
Press and hold
2
Keep the button pressed until step 4 is finished.
Press ENTER.
3
F
TV.
• Manufacturers’ codes are subject to change without notice. If they are
changed, this remote control cannot operate the equipment.
• Set the codes again after replacing the batteries of the remote control.
7
Operation
Before using the remote control to operate a
TV;
• Set the remote control mode selector to TV.
The following buttons are available:
: Turns TV on and off.
TV
F
TV VOL +/–
TV/VIDEO
CHANNEL +/–
1-10, 0, +10 (100+)
TV RETURN
: Adjusts the volume.
: Selects the input mode (either TV or
VIDEO).
: Changes the channels.
: Selects the channel.
: Alternates between the previously selected
channel and the current channel.
For DBS tuner or CATV converter
operations
You can operate your DBS tuner or CATV converter using the
remote control supplied with this system.
• Refer also to the instruction manuals supplied with your DBS
tuner or CATV converter.
7
To set the manufacturer’s code
Slide the remote control mode selector
1
to VCR/DBS.
Press and hold DBS.
2
Keep the button pressed until step 4 is finished.
15
Press ENTER.
3
Getting started
NOTE
IMPORTANT
NOTE
Press number buttons (1-9, 0) to enter
4
the manufacturer’s code (2 digits).
Examples:
For a GI Jerrold product:Press 0, then 1.
For a Sony product: Press 2, then 0.
Manufacturer Code
Echostar 21
GI Jerrold 01, 02, 03, 04, 05, 06, 07, 08
Hamin/Regal 15, 16, 17, 18
Pioneer 13, 14
RCA 19
Scientific Atlanta 09, 10
Sony 20
Zenith 11, 12
Release DBS.
5
Try operating your DBS tuner or CATV
6
converter by pressing
When your DBS tuner or CATV converter turns on or off, you
have entered the correct code.
If there is more than one code listed for your brand, try each
one until you enter the correct one.
NOTE
• Manufacturers’ codes are subject to change without notice. If they are
changed, this remote control cannot operate the equipment.
• Set the codes again after replacing the batteries of the remote control.
7
Operation
IMPORTANT
Before using the remote control to operate a
DBS tuner or CATV converter;
1 Set the remote control mode selector to
VCR/DBS
2Press
The following buttons are available:
VCR/DBS
F
CHANNEL +/–
1-10, 0, +10 (100+)
.
.
DBS
: Turns DBS tuner or CATV converter on and
off.
: Changes the channels.
: Selects the channel.
F
VCR/DBS.
For VCR operations
You can operate your VCR using the remote control supplied with
this system.
• Refer also to the instruction manuals supplied with your VCR.
7
To set the manufacturer’s code
Press number buttons (1-9, 0) to enter
4
the manufacturer’s code (2 digits).
Examples:
For a Philips VCR: Press 0, then 9.
For an NEC VCR: Press 2, then 5.
Manufacturer Code Manufacturer Code
JVC 01, 02, 03 Philips 09
Emerson 11, 26 RCA 05, 06
Fisher 29 Samsung 24
Funai 10, 14, 15, 16 Sanyo 21, 22, 23
Gold Star 12 Sharp 27, 28
Hitachi 04 Shintom 30
Mitsubishi 13 Sony 18, 19, 20
NEC 25 Zenith 08
Panasonic 07, 17
Release VCR.
5
Try operating your VCR by pressing
6
F
VCR/DBS.
When your VCR turns on or off, you have entered the correct
code.
If there is more than one code listed for your brand, try each
one until you enter the correct one.
• Manufacturers’ codes are subject to change without notice. If they are
changed, this remote control cannot operate the equipment.
• Set the codes again after replacing the batteries of the remote control.
7
Operation
Before using the remote control to operate a
VCR;
1 Set the remote control mode selector to
VCR/DBS
2 Press
The following buttons are available:
VCR/DBS
F
(play button): Starts playback.
3
: Stops operation.
7
: Pauses playback.
8
: Fast forwards video tape.
¢
: Rewinds video tape.
4
: Press this button together with 3 (play button)
REC
CHANNEL +/–
1-10, 0
.
.
VCR
: Turns VCR on and off.
to start recording or together with 8 to pause
recording.
: Changes the TV channels on the VCR.
: Selects the channel. (for the JVC’s VCR only)
1
2
3
Slide the remote control mode selector
to VCR/DBS.
Press and hold VCR.
Keep the button pressed until step 4 is finished.
Press ENTER.
When operating a VCR or DBS tuner/CATV converter;
• The source setting of VCR or DBS remains after you have changed
the remote control mode selector to
VCR or DBS tuner/CATV converter again, it is not necessary to press
or
VCR
after setting the remote control mode selector.
DBS
or TV. When operating
AUDIO
16
Basic operations
NOTE
Message area
This section mainly explains operations commonly used when you
enjoy this system.
• Turn on your TV and select the correct input mode on the TV.
English
IMPORTANT
Before using the remote control for the
following operation,
• Set the remote control mode selector to
.
AUD IO
Remote control
mode selector
Source
selecting
buttons
Turning the system on/off
7
To turn the power on
On the remote control:
Press
On the center unit:
Press
The STANDBY lamp goes off.
When DVD is selected as the source (Apg. 18), the opening
screen* appears on the TV screen.
*
The following messages may
appear in the message area
depending on the status of this
system.
• “OPEN”/“CLOSE”:
• “NOW READING”:
• “REGION CODE ERROR!”:
•“NO DISC”:
F
AUDIO.
F
STANDBY/ON.
Opening screen
Appears when opening or
closing the selected disc tray.
Appears when the system is
reading the disc information.
Appears when the Region Code of the DVD does not match the
code the center unit supports. The DVD cannot be played back.
Appears when no disc is loaded to the selected disc tray.
7
To turn the power off
On the remote control:
Press
On the center unit:
Press
The STANDBY lamp lights.
• The power supply to the subwoofer is linked to the center unit. The
• A small amount of the power is consumed even when the power is
• You can also turn on the system by pressing the following buttons;
F
AUDIO again.
F
STANDBY/ON again.
POWER ON lamp on the subwoofer lights green when the power is
turned on.
turned off (center unit only). This is called standby mode and the
STANDBY lamp lights in this mode. Unplug the power cord from the
AC outlet to turn the power off completely.
One of 0 buttons on the center unit
•
One of the source selecting buttons on the remote control
•
One of the
•
You can use the same buttons on the remote control except after
pressing
DISC (1-5)
FM/AM
buttons or 3 on the center unit.
.
Illumination lamp
17
Loading...