52110200304
RK-CPDP1
SERVICE MANUAL
TABLETOP STAND
RK-CPDP1
600
460
9309
82
245
Mass : 8kg
119.3
326
70
362.3
530
612.5
710
TABLE OF CONTENTS
1 ASSEMBLY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
2 PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
COPYRIGHT © 2003 VICTOR COMPANY OF JAPAN, LTD.
No.52110
2003/04
RK-CPDP1
ASSEMBLY INSTRUCTIONS
Assembly Instructions
Washer Washer
(long) (short)
Tabletop Stand
RK-CPDP1
1142
Stand Cover Screws Screws
Thank you for purchasing the Tabletop Stand.
please contact your retailer.
Please read this manual thoroughly in order to ensure correct assembly of the product.
The safety precautions on the back should be read first.
● Look at the diagram below and check the number of parts. If any parts are missing,
● You will need a Phillips screwdriver (+).
■ Composite Parts
Diagram
Part Name
Quantity
Precautions when installing a Plasma Display
1-2 (No.52110)
Precautions During Use
Mistaken use resulting from failure to read content marked with this symbol may cause accidents
leading to death or serious injury.
Mistaken use resulting from failure to read content marked with this symbol may cause accidents
limited to minor injury or property damage.
Caution
Carry out Plasma Display installation with at least 2 persons.
Avoid inserting fingers into the gap between the Tabletop Stand and the Plasma Display during installation, as fingers
For correct and safe use
Please read these precautions carefully before use.
The Symbols
may get trapped, causing injury.
The symbols used in this manual provide information and precautions regarding the product to encourage safe use
Warning
and to protect people and property from damage. The symbols and their meanings are as follows. Make sure you are
aware of the meaning of each symbol before reading the instructions.
Example of symbol use
Caution
symbol indicates content which explains actions that are prohibited. Details of prohibited content
Specific caution content is written within the diagram.
The
The symbol indicates content advising caution (including possible dangers and warnings).
are written either within the diagram or nearby.
Warning
Do not place the Tabletop Stand on an unsteady or slanting surface or other unstable location, as falls or injury
may result.
Do not move the Tabletop Stand with the device mounted. Vibration or shock may cause damage to the Tabletop
VICTOR COMPANY OF JAPAN, LIMITED
Stand's connectors, or the device may fall, causing injury.
Caution
Do not place heavy objects other than the stipulated device on the Tabletop Stand, as balance may be affected
and the device may fall and cause injuries.
Do not place the Tabletop Stand in direct sunlight or next to a heat source, as this may cause deformation or
discoloration.
Maintenance
Wipe the Tabletop Stand gently with a soft, dry cloth. Use of a wet cloth may result in surface discoloration or rusting
Do not drag the Tabletop Stand when moving it, as the metal legs may become bent or leave scratch marks on
floors.
of the frame.
© 2002 VICTOR COMPANY OF JAPAN, LIMITED
RK-CPDP1
Fitting the Cover on the Tabletop Stand
w Secure the cover in position at (H) with the 2 short
Washer Screws.
(F)
(G)
(H)
Attaching the Sub-Woofer to the Tabletop Stand.
q Connect the Speaker Cord (For the Woofer) to the Sub-Woofer and Plasma Display.
w After connecting the Speaker Cord, turn the Sub-Woofer so that the net cover faces outwards, and fit the
Sub-Woofer into (E) (Sub-Woofer Positioning Tabs).
*
While positioning the Sub-Woofer, care should be taken that the power cord/system cord should not get unplugged
or loosened-up from the Plasma Display.
(E) (Sub-Woofer Positioning Tabs)
The above diagram shows the Sub-Woofer in position in
the Tabletop Stand.
q Insert the Tabs (F) on the bottom of the Cover into
slots (G) on the Tabletop Stand.
(NET COVER)
(C)
Washer Screws.
w Secure the Plasma Display at (C) with the 4 long
Mounting the Plasma Display on the Tabletop Stand
Plasma Mounting Brackets (B).
This task must be performed by at least two persons.
*
q Insert the Plasma Display Base (A) into the
(A)
(B)
Connecting the Plasma Display wiring
q The system cable should be fed out through (D) (indented section).
w Connect the Speaker Cord (for the Front Speaker) to the Front Speaker and the Plasma Display.
(D) (Indented section)
(No.52110)1-3
RK-CPDP1
r
EXPLODED VIEW
PARTS LIST
1
3
Sub-Woofe
2
EXPLODED VIEW PARTS LIST
Ref.No. Part No. Part Name Qty Description
1 LC11579-001A COVER 1
2 C500S1 SCREW 4 For STAND (LONG) M5 x 30
3 C500S2 SCREW 2 For COVER (SHORT) M4 x 12
1-4 (No.52110)
PACKING
RK-CPDP1
7
11
10
4
6
Stand
8
9
Cover
5
2
3
1
12
PACKING PARTS LIST
Ref.No. Part No. Part Name Qty Description
1 C500P1 PACKING CASE 1
2 C500P3 CUSHION 1
3 C500P4 CUSHION 1
4 C500P6 CUSHION 1
5 C500P2 PACKING CASE 1
6 C500P7 CUSHION 2
7 C500P5 CUSHION 1
8 C500F1 POLY BAG 1 For STAND
9 C500F2 POLY BAG 1 For COVER
10 C500F3 POLY BAG 1 For SCREW
11 CPDP1INST INSTSHEET 1
12 CP30902-074 POS LABEL 1
(No.52110)1-5
RK-CPDP1
VICTOR COMPANY OF JAPAN, LIMITED
AV & MULTIMEDIA COMPANY DISPLAY CATEGORY 12, 3-chome, Moriya-cho, kanagawa-ku, Yokohama, kanagawa-prefecture, 221-8528, Japan
(No.52110)
Printed in Japan
200304WPC
Loading...