JVC MX-K30 User Manual

Download

Page 1

COMPACT COMPONENT SYSTEM

MX-K30/MX-K10

Consists of CA-MXK30 and SP-MXK30 Consists of CA-MXK10 and SP-MXK10

CA-MXK30 SP-MXK30 CA-MXK10 SP-MXK10

3-CD

PLAY & EXCHANGE

CD-R/RW PLAYBACK

SOUND

DUAL D/A CONVERTER

PROGRAM

PANDOM

PRESET

TUNING

TAPE A / B

CD SYNCHRO RECORDING

MODE

REPEAT

D C

ACTIVE

D C

BASS EX.

REC / PLAY

CD1CD2CD

REPEAT

SOUND MODE

ACTIVE

BASS EX.

COMPACT COMPONENT SYSTEM

STANDBY/ON

SLEEP

AUX

FM MODE

FM /AM

PROGRAM /RANDOM

TAPE

A/B

VOLUME

KARAOKE

FADE

MUTING

ECHO

MX-K30

1 BIT

STANDBY/ON

STANDBY

SET

CANCEL

/ DEMO

TAPE

AUX

/ AM

PHONES

REC START / STOPCD REC START DUBBING

MIC

MIC LEVEL

CLOCK /TIMER

COMPU PLAY CONTROL

MIN MAX

EJECT EJECT

FULL - LOGIC CONTROL

PLAY

DISC SKIP

CD1CD2CD

REPEAT

SOUND MODE

ACTIVE

BASS EX.

SP-MXK30

STANDBY/ON

SLEEP

AUX

FM MODE

FM /AM

PROGRAM /RANDOM

TAPE

A/B

VOLUME

KARAOKE

FADE

MUTING

ECHO

SP-MXK10

CA-MXK30

3-CD

COMPACT COMPONENT SYSTEM

STANDBY

PHONES

PLAY & EXCHANGE

MX-K10

1 BIT

DUAL D/A CONVERTER

PROGRAM

FM / AM

PLAY

REC START / STOPCD REC START

CANCEL

COMPU PLAY CONTROL

FULL - LOGIC CONTROL

PANDOM

SET

PRESET

/ DEMO

TAPE

TUNING

DUBBING

CLOCK

TAPE

/TIMER

A / B

CD SYNCHRO RECORDING

STANDBY/ON

AUX

MIC

MIC LEVEL

MIN MAX

EJECT EJECT

CA-MXK10

SP-MXK30

CD-R/RW PLAYBACK

SOUND

MODE

REPEAT

DISC SKIP

D C

ACTIVE

BASS EX.

REC / PLAY

SP-MXK10

INSTRUCTIONS

For Customer Use:

Enter below the Model No. and Serial No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference.

Model No.

Serial No.

LVT0860-010C

44-1107-1

[U]

Page 2

Warnings, Cautions and Others

CAUTION

To reduce the risk of electrical shocks, fire, etc.:

1. Do not remove screws, covers or cabinet.

2. Do not expose this appliance to rain or moisture.

IMPORTANT FOR LASER PRODUCTS /

REPRODUCTION OF LABELS /

CLASSIFICATION LABEL, PLACED ON EXTERIOR SURFACE

Caution –– switch!

Disconnect the mains plug to shut the power off completely. The switch in any position does not disconnect the mains line. The power can be remote controlled.

WARNING LABEL, PLACED INSIDE THE UNIT

CLASS 1 LASER PRODUCT

DANGER

1. Invisible laser radiation when open and interlock failed or defeated. Avoid direct exposure to beam.

CAUTION

1.Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel.

2.Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

G-1

Page 3

Caution: Proper Ventilation

To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows: 1 Front: No obstructions and open spacing. 2 Sides/ Top/ Back: No obstructions should be placed in the areas shown by the dimensions below. 3 Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of 10 cm or more.

Front view Side view

15cm

1cm

CA-MXK30/ CA-MXK10

1cm

CAUTION

1.Do not block the ventilation openings or holes. (If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.)

2.Do not place any naked flame sources, such as lighted candles, on the apparatus.

3.When discarding batteries, environmental problems must be considered and local rules or laws governing the disposal of these batteries must be followed strictly.

4.Do not expose this apparatus to rain, moisture, dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

15cm

CA-MXK30/ CA-MXK10

10cm

G-2

Page 4

Introduction

Thank you for purchasing the JVC Compact Component System. We hope it will be a valued addition to your home, giving you years of enjoyment.

English

Be sure to read this instruction manual carefully before operating your new stereo system. In it you will find all the information you need to set up and use the system. If you have a query that is not answered by the manual, please contact your dealer.

Features

Here are some of the things that make your System both powerful and simple to use. ❏ The controls and operations have been redesigned to make them very easy to use, freeing you to just enjoy the

music.

• With JVC’s COMPU PLAY you can turn on the System and automatically start the Radio, Cassette Deck, or CD Player with a single touch.

❏ The great SEA (Sound Effect Amplifier) effects Rock, Pop and Classics are provided. ❏ The Active Bass EX. (Extension) circuitry faithfully reproduces low frequency sounds. ❏ A 45-station preset capability (30 FM and 15 AM) in addition to auto-seek and manual tuning. ❏ CD changer function can operate 3 discs.

• Discs can be changed during play using the Carrousel tray (rotational tray).

• Continuous, random or program play of 3 discs.

❏ Two Decks enabling tape dubbing. ❏ You can use conventional tapes and CDs for Karaoke with the voice masking system. With an optional microphone, you can replace the

lead singer’s voice on your favorite songs with your own.

• Digital Echo applied to your voice through the microphone gives you a professional sound.

❏ Timer functions; Daily Timer, REC (Recording) Timer, and Sleep Timer. ❏ You can connect various external units, such as an MD recorder. ❏ The CD Player can play back a CD-R and CD-RW.

How This Manual Is Organized

• Basic information that is the same for many different functions - e.g. setting the volume - is given in the section “Basic Operations”, and not repeated under each function.

• The names of buttons/controls and display messages are written in all capital letters: e.g. FM/AM, “NO DISC”.

• If the button names on the Unit and the Remote Control are the same, the description on where the button is used will be omitted.

• System functions are written with an initial capital letter only: e.g. Normal Play.

Use the table of contents to look up specific information you require. We have enjoyed making this manual for you, and hope it serves you in enjoying the many features built into your System.

IMPORTANT CAUTIONS

Installation of the System

• Select a place which is level, dry and neither too hot nor too cold. (Between 5°C and 35°C or 41°F and 95°F.)

• Leave sufficient distance between the System and a TV.

• Do not use the System in a place subject to vibrations.

Power cord

• Do not handle the power cord with wet hands!

• Some power is always consumed as long as the power cord is connected to the wall outlet.

• When unplugging the System from the wall outlet, always pull the plug, not the power cord.

Malfunctions, etc.

• There are no user serviceable parts inside. In case of system failure, unplug the power cord and consult your dealer.

• Do not insert any metallic object into the System.

Page 5

Introduction ...................................................................................................................1

Features.................................................................................................................................................... 1

How This Manual Is Organized............................................................................................................... 1

IMPORTANT CAUTIONS..................................................................................................................... 1

Table of Contents ..........................................................................................................2

Getting Started ..............................................................................................................3

Accessories .............................................................................................................................................. 3

Set the VOLTAGE SELECTOR Switch.................................................................................................3

How To Put Batteries In the Remote Control..........................................................................................3

Using the Remote Control....................................................................................................................... 4

Connecting the FM Antenna.................................................................................................................... 4

Connecting the AM Antenna...................................................................................................................5

Connecting the Speakers ......................................................................................................................... 5

Connecting External Equipment.............................................................................................................. 6

Connecting to the Wall Outlet.................................................................................................................6

DEMO Mode ........................................................................................................................................... 6

COMPU Play........................................................................................................................................... 6

Basic Operations...........................................................................................................7

Turning the Power On and Off................................................................................................................ 7

Adjusting the Volume.............................................................................................................................. 7

Fade-out Muting (FADE MUTING) ....................................................................................................... 8

Reinforcing the Bass Sound (ACTIVE BASS EX.)................................................................................ 8

Selecting the Sound Mode (SOUND MODE)......................................................................................... 8

Entering the Number with the Remote Control (Numeric Keys)............................................................ 8

Using the Tuner .............................................................................................................9

Tuning In a Station .................................................................................................................................. 9

Presetting Stations ................................................................................................................................. 10

To Change the FM Reception Mode ..................................................................................................... 10

Using the CD Player ....................................................................................................11

To Load CDs ......................................................................................................................................... 12

To Unload CDs...................................................................................................................................... 12

Basics of Using the CD Player-Normal Play......................................................................................... 13

Programming the Playing Order of the Tracks...................................................................................... 14

Random Play.......................................................................................................................................... 15

Repeating Tracks ................................................................................................................................... 15

Tray Lock Function ............................................................................................................................... 15

Using the Cassette Deck (Listening to a Tape) ........................................................16

Playing a Tape ....................................................................................................................................... 16

Using the Cassette Deck (Recording) ......................................................................17

Standard Recording ............................................................................................................................... 18

CD Synchro Recording.......................................................................................................................... 18

Tape to Tape Recording (DUBBING)................................................................................................... 18

Using an External Equipment ....................................................................................19

Listening to the External Equipment..................................................................................................... 19

Using the Timers .........................................................................................................20

Setting the Clock ...................................................................................................................................20

Setting the Daily Timer ......................................................................................................................... 21

Setting the REC (Recording) Timer...................................................................................................... 22

Setting the SLEEP Timer ...................................................................................................................... 24

Timer Priority ........................................................................................................................................ 24

Using the Microphone.................................................................................................25

Singing Along with Karaoke ................................................................................................................. 25

Microphone Mixing............................................................................................................................... 26

Playing the Microphone Sound through the Speakers........................................................................... 26

Care And Maintenance................................................................................................27

Troubleshooting ..........................................................................................................28

Specifications ..............................................................................................................28

English

Page 6

Getting Started

Accessories

English

Make sure that you have all of the following items, which are supplied with the System.

AM Loop Antenna (1) Remote Control (1) Batteries (2) FM Wire Antenna (1) AC Plug Adaptor (1)

If any of these items are missing, contact your dealer immediately.

Set the VOLTAGE SELECTOR Switch

To avoid damaging the System, set the voltage before plugging in the System. Set the correct voltage for you area with the VOLTAGE SELECTOR switch on the back of the Unit. Use a screwdriver to rotate the selector so the number the voltage mark is pointed at is the same as the voltage.

Voltage mark

CAUTION:

• Make all connections before plugging the System into an AC power outlet.

How To Put Batteries In the Remote Control

Match the polarity (+ and –) on the batteries with the + and – markings in the battery compartment.

R6P(SUM-3)/AA(15F)

CAUTION:

• Handle batteries properly.

❏ To avoid battery leakage or explosion:

• Remove batteries when the Remote Control will not be used for a long time.

• When you need to replace the batteries, replace both batteries at the same time with new ones.

• Do not use an old battery with a new one.

• Do not use different types of batteries together.

Page 7

Getting Started

Using the Remote Control

The Remote Control makes it easy to use many of the functions of the System from a distance of up to 7m away. You need to point the Remote Control at the remote sensor on the System’s fron panel.

3-CD

Remote sensor

PLAY & EXCHANGE

COMPACT COMPONENT SYSTEM

STANDBY/ON

STANDBY

AUX

/ AM

PHONES

REC START / STOPCD REC START

MIC

MIC LEVEL

MIN MAX

EJECT EJECT

PLAY

CANCEL

/ DEMO

TAPE

COMPU PLAY CONTROL

FULL - LOGIC CONTROL

1 BIT

DUAL D/A CONVERTER

PANDOM

SET

PRESET

TUNING

DUBBING

CLOCK /TIMER

A / B

CD SYNCHRO RECORDING

CD-R/RW PLAYBACK

SOUND

MODE

REPEAT

PROGRAM

TAPE

DISC SKIP

ACTIVE

BASS EX.

REC / PLAY

CAUTION:

• Make all connections before plugging the System into an AC power outlet.

Connecting the FM Antenna

Using the Supplied Wire Antenna

English

FM wire antenna (supplied)

Strip vinyl shield from cut line, twist wire core.

Using an FM 75-Ohm Antenna Cable (not Supplied)

If reception is poor, connect the outside antenna.

Extend the supplied FM Wire Antenna horizontally.

Outdoor FM antenna cable (not supplied)

• Before attaching a 75 ohm coaxial lead (the kind with a round wire going to an outdoor antenna), disconnect the supplied FM Wire Antenna.

Page 8

Getting Started

Connecting the AM Antenna

English

Rear Panel of the Unit

AM loop antenna (Supplied)

AM antenna wire (not supplied) If reception is poor, connect the outside antenna.

• Even when connecting an outside AM antenna, keep the indoor AM loop connected.

Turn the loop until you have the best reception.

Attach the AM loop to its base by snapping the tabs on the loop into the slot in the base.

CAUTION:

• To avoid noise, keep antennas away from the System, the connecting cord and the AC power cord.

Connecting the Speakers

1. Open each of the terminals to connect the speaker wire leads.

2. Connect the speaker cords to the Speaker terminals of the Unit. Connect the red (+) and black (–) cords of the right side speaker to the red (+) and black (–) terminals marked RIGHT on the System. Connect the red (+) and black (–) cords of the left side speaker to the red (+) and black (–) terminals marked LEFT on the System.

3. Close each of the terminals to securely connect the cords.

Right side (rear view) Left side (rear view)

Red

Black

CAUTIONS:

• A TV may display irregular colors if located near the speakers. If this happens, set the speakers away from the TV.

• Use speakers with the correct impedance only. The correct impedance is indicated on the rear panel.

Page 9

Getting Started

Connecting External Equipment

Connect a signal cord (not supplied) between the System’s AUX-IN terminals and the output terminals of the external MD recorder, tape deck, etc. You can then listen to the external source through the System.

Signal cord (not supplied)

Pin-plug x 2Pin-plug x 2

MD recorder, tape deck, etc. (not supplied)

Connecting to the Wall Outlet

Plug the AC power cord into the wall outlet. Now, your System is at your command!

DEMO Mode

When the System is connected to the wall outlet, a DEMO mode displaying some of the system’s features automatically starts.

To turn the DEMO display off, press any of the operation buttons. The DEMO display automatically stops. To turn the DEMO display on, press the DEMO button on the Unit for more than 2 seconds.

CANCEL

/ DEMO

(For 2 seconds)

English

• The DEMO display will automatically turn on again if no button operation is made for 2 minutes. To cancel this auto DEMO display function, press the CANCEL button on the Unit during DEMO display.

COMPU Play

JVC’s COMPU PLAY feature lets you control the most frequently used System functions with a single touch. With One Touch Operation you can play a CD, a tape, turn on the radio, or listen to an external equipment with a single press of the play button for that function. One Touch Operation turns the power on for you, then starts the function you have specified. If the System is not ready (no CD or tape in place), the System still powers on so you can insert a CD or tape. How One Touch Operation works in each case is explained in the section dealing with that function. The COMPU PLAY buttons are:

On the Unit

CD 6 button FM/AM button TAPE 3 button AUX button CD1, CD2 and CD 3 buttons CD Open/Close 0 button

On the Remote Control

CD 6 button FM/AM button TAPE 3 button AUX button CD1, CD2 and CD 3 buttons

Page 10

Basic Operations

)

English

Numeric keys

SOUND MODE

ACTIVE BASS EX.

CD1CD2CD

PROGRAM

REPEAT

/RANDOM

SOUND

KARAOKE

MODE

ACTIVE

BASS EX.

ECHO

FM MODE

TAPE

A/B

FADE

MUTING

STANDBY/ON

SLEEP

AUX

FM /AM

TAPE

VOLUME

% STANDBY/ON

Display

STANDBY indicator

% STANDBY/ON

PHONES

VOLUME +,–

FADE MUTING

Level bar

3-CD

PLAY & EXCHANGE

COMPACT COMPONENT SYSTEM

STANDBY/ON

STANDBY

AUX

/ AM

PHONES

REC START

/ STOPCD REC START

MIC

MIC LEVEL

COMPU PLAY CONTROL

MIN MAX

EJECT EJECT

FULL - LOGIC CONTROL

PLAY

1 BIT

DUAL D/A CONVERTER

PROGRAM

PANDOM

SET

CANCEL

/ DEMO

TAPE

DUBBING

PRESET

TUNING

CLOCK

TAPE

/TIMER

A / B

CD SYNCHRO RECORDING

Various information

BASS

S.MODE

Status bar (Indicates various statuses.)

CD-R/RW PLAYBACK

SOUND

MODE

REPEAT

BASS EX.

ACTIVE

REC / PLAY

BASS indicator Sound Mode indicator

I D

SOUND MODE

VOLUME

ACTIVE BASS EX.

* When the System is in use, the display shows other items as well.

For simplicity, we show here only the items described in this section.

Turning the Power On and Off

Turning the System On

Press the

The display comes on and “WELCOME” is displayed once. The STANDBY indicator goes out. The System comes on ready to continue in the mode it was in when the power was last turned off.

• For example, if the last thing you were doing was listening to a CD, you are now ready to listen to a CD again. If you wish, you can change to another source.

• If you were listening to the Tuner last, the Tuner comes on playing the station it was last set to.

Turning the System Off

Press the % STANDBY/ON button again.

“GOOD BYE” is displayed and the display goes out, except for the clock display. The STANDBY indicator lights up. (The display is dimmed.)

STANDBY/ON button.

STANDBY/ON

STANDBY

STANDBY/ON

• Some power is always consumed even though power is turned off (called Standby mode).

• To switch off the System completely, unplug the AC power cord from the wall outlet. When you unplug the AC power cord, the clock will be reset to 0:00 immediately.

Adjusting the Volume

Turn the VOLUME control on the Unit clockwise to increase the volume or turn it counterclockwise to decrease the volume. Press the VOLUME + button on the Remote Control to increase the volume or press the VOLUME – button on the Remote Control to decrease the volume.

You can set the volume level to MIN, 1-31, or MAX.

CAUTION:

• DO NOT turn on the System and/or start playing any source without first setting the VOLUME control to minimum, as a sudden blast of sound could damage your hearing, speakers and/or headphones.

For private listening

Connect a pair of headphones to the PHONES jack. No sound comes out of the speakers. Be sure to turn down the volume before connecting or putting on headphones.

Page 11

Basic Operations

Fade-out Muting (FADE MUTING)

You can mute the output with one touch operation.

To muting the output, press the FADE MUTING button on the Remote Control. The output is faded out. To release muting, press the FADE MUTING button once again. The output is faded in to the previous level.

• After Fade-out Muting, turning the VOLUME control on the unit or pressing the VOLUME button on the Remote Control will increase the volume from MIN. setting.

Reinforcing the Bass Sound (ACTIVE BASS EX.)

The richness and fullness of the bass sound is maintained regardless of how low you set the volume. You can use this effect only for playback.

To get the effect, press the ACTIVE BASS EX. (Extension) button. The “BASS” indicator lights up and “ACTIVE BASS EXTENSION” appears on the display. To cancel the effect, press the button again. The “BASS” indicator goes out and “OFF” appears on the display.

Selecting the Sound Mode (SOUND MODE)

Entering the Number with the Remote Control (Numeric Keys)

You will use the number keys on the Remote Control to enter numbers for presetting stations, recalling the preset stations, or programming the playing tracks on CDs. How to enter the number with the number keys is explained here.

Examples:

• To enter number 5, press 5.

• To enter number 15, press +10, then 5.

• To enter number 20, press +10, then 10.

• To enter number 25, press +10, +10, then 5.

English

You can select one of 3 SEA (Sound Effect Amplifier) modes. You can use this effect only for playback.

On the Unit

To get the effect, press one of the Sound Mode buttons, ROCK, POP, or CLASSIC. The selected Sound Mode name “ROCK”, “POP”, or “CLASSIC” appears on the display. The “S.MODE” indicator also lights up on the display. To cancel the effect, press the currently selected mode button again. When the effect is canceled, the “S.MODE” indicator goes out. For example, if the current Sound Mode is ROCK, press the ROCK button again. “FLAT” appears on the display, showing that no sound effect is applied.

ROCK Boosts low and high frequencies. Good for

acoustic music.

POP Good for vocal music. CLASSIC Set for wide and dynamic sound stereo

systems.

FLAT No sound effect applies.

On the Remote Control

Press the SOUND MODE button until Sound Mode you want appears on the display. The “S.MODE” indicator lights up on the display. Each time you press the button, the Sound Mode changes as follows:

ROCK = POP = CLASSIC = FLAT = (back to the beginning) To cancel the effect, press the SOUND MODE button until

“FLAT” appears on the display. The “S.MODE” indicator goes out.

Page 12

Using the Tuner

English

CD1CD2CD

PROGRAM

REPEAT

/RANDOM

SOUND MODE

KARAOKE

ACTIVE

BASSEX.

ECHO

FM MODE

TAPE A/B

FADE

MUTING

STANDBY/ON

SLEEP

AUX

FM /AM

TAPE

VOLUME

Numeric keys

FM/AM FM MODE

3-CD

PLAY& EXCHANGE

SET

FM/AM

COMPACT COMPONENT SYSTEM

STANDBY/ON

STANDBY

AUX

/ AM

PHONES

RECSTART

/STOPCDRECSTART

MIC

MICLEVEL

MIN MAX

COMPU PLAY CONTROL

1BIT

DUALD/A

CONVERTER

PROGRAM

PANDOM

SET

CANCEL

/DEMO

PRESET

TAPE

TUNING

DUBBING

CLOCK

TAPE

/TIMER

A/B

EJECT EJECT

PLAY

FULL - LOGIC CONTROL

CD SYNCHRO RECORDING

Band display, Frequency display, Preset channel

kHz MHz

MONO

FM mode indicators

REPEAT

CD-R/RWPLAYBACK

SOUND

MODE

ACTIVE

BASSEX.

REC / PLAY

DISCSKIP

* When the System is in use, the display shows other items as well.

For simplicity, we show here only the items described in this section.

You can listen to FM and AM stations. Stations can be tuned in manually, automatically, or from preset memory storage.

❏ Before listening to the radio:

• Make sure that both the FM and AM antennas are correctly connected. (See pages 4 and 5).

Setting the AM Tuner Interval Spacing

When shipped, the AM tuner interval is set to 9kHz spacing (50 kHz spacing for FM broadcast). You can change it to 10kHz spacing. To select 10kHz intervals, while holding down the ¢ button on the Unit in Standby mode, press the % button on the Unit to turn on the power (at the same time, the 100kHz spacing is selected for FM broadcast). To select 9kHz intervals again, while holding down the 4 button on the Unit in Standby mode, press the % button on the Unit to turn on the power.

[10 kHz Intervals] [9 kHz Intervals]

STANDBY

STANDBY/ON

STANDBY

STANDBY/ON

One Touch Radio

Just press the FM/AM button to turn on the System and start playing the station you were last tuned to.

❏ You can switch from any other sound source to the radio by

pressing the FM/AM button.

Tuning In a Station

Press the FM/AM button.

The Band and Frequency you were last tuned to appear on the display. (If the last station was selected using the preset number, the preset number appears first.) Each time you press the button, the band alternates between FM and AM.

/ AM

(on the Unit)

Select a station using one of the following

methods.

FM /AM

(on the Remote Control)

Page 13

Using the Tuner

• Manual Tuning

Briefly press the 22 or ¡ button on the Unit to move from frequency to frequency until you find the station you want.

• Auto Tuning

If you hold down the 22 or ¡ button on the Unit for 1 second or more and then release it, the frequency changes down, or up, automatically until a station is found.

• Preset Tuning (Possible only after presetting stations) Preset tuning using the Unit:

Select the preset number you want, using the 4 or ¢ button.

Example:

Press the ¢ button until the preset number “P-12” appears on the display. After 2 seconds, the display will show the preset number’s band and frequency.

PRESET

Preset tuning using the Remote Control:

Enter the preset number you want to recall using the numeric keys. See “Entering the Number with the Remote Control” on page 8.

(After 2 seconds)

kHz MHz

Example:

Press +10, then 2 to recall the preset number 12. After 2 seconds, the display will show the preset number’s band and frequency.

• In AM broadcast, reception sensitivity will be changed by turning the AM loop antenna. Turn the AM loop antenna for best reception.

Presetting Stations

You can preset up to 30 FM stations and up to 15 AM stations.

Using the Unit

Select a band by pressing the FM/AM button.

Press the

button to tune in a

station. Press the SET button.

“SET” will blink for 5 seconds.

Press the

button to select the

preset number.

: Increases the preset number by 1.

: Decreases the preset number by 1.

Press the SET button.

“STORED” appears and, after 2 seconds, the display returns to the band/frequency display.

Repeat above steps 1 to 5 for each station

you want to store in memory with a preset number.

To change the preset stations, repeat the same steps as

above.

• In step 4, you can select the preset number using the numeric keys on the Remote Control. See “Entering the Number with the Remote Control” on page 8.

CAUTION:

• Even if the System is unplugged or if the power failure occurs, the preset stations will be stored for a few days. However, in case the preset stations are erased, you will need to preset the stations again.

To Change the FM Reception Mode

When you are tuned in to an FM stereo broadcast, the “ST (Stereo)” indicator lights up and you can hear stereo effects. If an FM stereo broadcast is hard to receive or noisy, you can select Monaural mode. Reception improves, but you lose stereo effect.

English

• Preset numbers may have been set to factory test frequencies prior to shipment. This is not a malfunction. You can preset the stations you want into memory by following one of the presetting methods below.

• During presetting stations, if no button operation is made for 5 seconds, the display returns to the band/frequency display. In this case, repeat steps from the beginning.

/ AM

When changing the Band

TUNING

SET SET

FM=30, AM=15

Press the FM MODE button on the Remote Control so that the “MONO” indicator lights up on the display.

FM MODE

ST MONO

To restore the stereo effect, press the FM MODE button on

the Remote Control so that the “MONO” indicator goes off.

Page 14

Using the CD Player

English

Numeric keys

CD1-CD3

REPEAT

PROGRAM /RANDOM

CD1CD2CD

PROGRAM

REPEAT

/RANDOM

SOUND

KARAOKE

MODE

ACTIVE

ECHO

BASSEX.

FM MODE

TAPE

A/B

FADE

MUTING

STANDBY/ON

SLEEP

AUX

FM /AM

TAPE

VOLUME

CD 6

CANCEL

SET

CD 6

22 ¡

COMPACT COMPONENT SYSTEM

STANDBY/ON

STANDBY

AUX

PHONES

MIC

MIN MAX

EJECT EJECT

MICLEVEL

/ AM

PLAY

RECSTART

/STOPCDRECSTART

COMPU PLAY CONTROL

FULL - LOGIC CONTROL

CANCEL

/DEMO

TAPE

DUBBING

Track number, Playing time, Program number, etc.

PRGMREPEAT

RANDOM ALL1CD

Play mode indicator

Repeat indicator

3-CD

PLAY& EXCHANGE

1BIT

DUALD/A CONVERTER

PROGRAM

PANDOM

SET

PRESET

TUNING

CLOCK

TAPE

/TIMER

A/B

CD SYNCHRO RECORDING

Disc indicators

1 2 3

REPEAT

CD-R/RWPLAYBACK

SOUND

BASSEX.

MODE

ACTIVE

REC / PLAY

DISCSKIP

CD Open/ Close 0

DISC SKIP

CD1-CD3

* When the System is in use, the display shows other items as well.

For simplicity, we show here only the items described in this section.

The CD Player has the rotational disc tray that can accommodate 3 CDs. You can use Normal, Program, Random, or Repeat Play.

Normal Play: Can continuously play all the tracks on all

the CDs.

Program Play: Can play all the programmed tracks on all

the CDs in the programmed order.

Random Play: Can play all the tracks on all the CDs in ran-

dom order.

Repeat Play: Can repeat all the tracks on all the CDs, the

tracks on one of the CDs, or just one of tracks on one CD.

Here are the basic things you need to know to play CDs and locate the different tracks on them.

About the Disc Indicator

Disc Number indicator

Selected Disc indicator

Disc Rotation indicator

The Disc indicator consists of the following three kinds of indicators:

Disc Number indicator: Lights all the time. Selected Disc indicator:Lights for the currently selected

disc number.

Disc Rotation indicator:Runs when the selected CD is

playing or paused. This indicator goes out if a CD is not loaded for the selected disc number. Once the tray is ejected, the Disc Rotation indicators for all disc numbers are lit. However, when the empty disc number is selected, the Disc Rotation indicator for the disc number goes out.

Page 15

Using the CD Player

Example of indication:

When CD door has ejected once and then CD-1 is pressed. (DISC1 is selected)

Shows that this disc number is selected.

1 2 3

Shows that the disc is rotating.

One Touch Play

The power comes on, and operations are done automatically. ❏ By pressing the CD 6 button, the System will come on, and if

a CD is loaded for the disc number that was lastly selected, it will start playing from the first track.

❏ By pressing the CD1-CD3 button, the System will come on, and

if a CD is already loaded for the selected disc number, it will start play from the first track.

To Load CDs

Press the CD Open/Close 0 button on the

Unit to open the tray. Place a CD, with its label side up, onto the

tray.

Be sure that the CD is securely seated on the disc tray.

With the label side up

❏ When you use an 8 cm CD, place it on the inner circle of the tray. ❏ You can load CDs while listening to the other source. ❏ When power is turned off with the tray opened, the tray is auto-

matically closed.

❏ If the CD cannot be read correctly (because it is scratched, for

example), “ 0 0:00” appears on the display.

To Unload CDs

Take out the CD as shown below.

While the CD Player is stopped, press the CD

Open/Close tray.

Remove the CD, then press the DISC SKIP

button on the Unit.

The tray turns for the next CD.

Repeat step 2 to remove all the CDs.

Press the CD Open/Close 0 button on the

Unit to close the tray.

❏ You can remove CDs while listening to the other source.

• You can also remove the CDs during playback. However, in this case, you can only remove the CDs that are not being played back.

button on the Unit to open the

English

STANDBY/ON

STANDBY

SET

CANCEL

PRESET

/ DEMO

Press the DISC SKIP button on the Unit and

P I K

C S I

place the next CD.

When you press the button, the tray turns for the next CD.

Repeat step 3 for the last CD.

Press the CD Open/Close 0 button on the

Unit.

The tray is closed.

• When placing a disc in the tray, be sure to position the disc inside the recess correctly. Otherwise, the message “No disc” will appear in the display, and the disc may be damaged or the Unit may be damaged when the tray is opened, or it may be difficult to remove the disc from the Unit.

Page 16

Using the CD Player

Basics of Using the CD Player-

English

Normal Play

To Play CDs

Load CDs.

Press one of the Disc button (CD1-CD3) you

want to play.

The selected disc number (e.g. “CD-1” ) appears on the display. The first track of the selected CD begins playing. When the first CD finishes playing, the next and the third CDs are continuously played back. When the last CD has finished playing, the CD Player automatically stops.

Examples:

CD1 = CD2 = CD3 = (stop) CD2 = CD3 = CD1 = (stop)

❏ You can start to play the currently selected disc by simply press-

ing the CD 6 button.

While playing the CD, the following will appear on the display.

1 2 3

• Removing/changing the CDs during playback

While playing back a CD (e.g. CD-1), you can remove or change the other CDs (e.g. CD-2 and CD-3) by pressing the CD Open/ Close 0 button. After removing or changing, press the same button to close the tray.

To Select a Track

During playback (using the 4 or ¢ button):

Briefly press the 4 or ¢ button to select the track you want to play. By pressing the button, you can skip to the next track or skip back to the previous track.

• The selected track starts playing.

• Press the ¢ button once to skip to the beginning of the next

track. (You can skip to the next CD (e.g. CD-1 = CD-2 = CD-3).)

• Press the 4 button to skip to the beginning of the current

track. Press twice quickly to skip to the beginning of the previous track. (You cannot skip back to the previous CD.)

In Stop mode (using the 4 or ¢ button):

By briefly pressing the 4 or ¢ button, the CD Player operates in the same way as during playback, except the following points.

• The buttons are effective only for the currently selected CD.

Using the numeric keys on the Remote Control:

Using the numeric keys, you can directly select the track on the currently selected CD.

• The selected track starts playing. For example, press +10, then 5 to play back the track number 15. See “Entering the Number with the Remote Control” on page 8.

Track number

• When the Disc button (CD1-CD3) is pressed with the tray opened, the tray is closed and the selected CD automatically begins playing.

To stop playing the CD, press the 7 button. The following in- formation for the CD is displayed.

Total track number Total playing time

(After 5 seconds)

Track number Playing time

To pause, press the CD 6 button. The playing time indication blinks on the display. To cancel pause, press the CD 6 button again. Play continues from the point where it was paused. To remove the CD, stop playing and press the CD Open/Close 0 button on the Unit.

Tips:

• Playing back the CD using the DISC SKIP button

You can also play the CDs using the DISC SKIP button. During playback, each time you press the button, the next CD is automatically played back. If the next disc tray is empty, the disc tray is automatically skipped.

Elapsed playing time

CD is playing.

1 2 3

Search Play

Holding down the following buttons, during playback, will fast forward/backwards the CD so you can quickly find a particular passage in the track you are listening to.

• 22 or ¡ button on the Unit

• 4 or ¢ button on the Remote Control

Page 17

Programming the Playing Order of the Tracks

You can program the playing order of the tracks on all the CDs. Note that you can only make a program when the CD Player is stopped.

❏ You can program up to 32 tracks in any desired order including

the same tracks.

To Make a Program

Load CDs

In Stop mode, set the CD Player in Program

Play mode.

On the Unit

Press the PROGRAM button to light the “PRGM” indicator on the display. At the same time, “PROGRAM” appears on the display.

On the Remote Control

Press the PROGRAM/RANDOM button until “PROGRAM” appears on the display. The “PRGM” indicator also lights up on the display. Each time you press the button, the display changes as follows: PROGRAM = RANDOM = Blank display (Normal Play) = (back to the beginning)

• If a program is already made, the last step of the program will be displayed.

Press one of the Disc button (CD1-CD3) to

select the CD you want to program.

The display will change to the Program Entry display.

PRESET

Disc number

Track number

Select the track you want to program.

Using the Unit

While the display is blinking, press the 4 or ¢ button to select the track, then press the SET button within 5 seconds. The program order number will be assigned from P-1.

Using the CD Player

Repeat steps 3 and 4 to program other tracks

on the same CD or the other CD. To play the program, Press the CD

but-

ton.

For details, see “To Play the Program You Have Made” mentioned below.

To delete all the tracks in the program, while the CD Player is stopped, press the 7 button. To Modify the Program, while the CD Player is stopped, press the CANCEL button, the last track in the program is deleted. To add new tracks to the end of the program, repeat above steps 3 and

• If you try to program a track number that does not exists on the CD, your entry will be ignored.

• If you try to program the 33rd track, “FULL” appears on the display.

To Play the Program You Have Made

Press the CD 6 button. The System plays the tracks in the order you have programmed them.

• To use Repeat Play for Program Play, press the REPEAT button to select “ALL” or “1” before starting playback. For details, see “Repeating Tracks” on page 15.

❏ You can skip to a particular program track by pressing the 4

or ¢ button during Program Play.

❏ To stop playing, press the 7 button once. If you press the 7 but-

ton, while the CD Player is stopped, the program is deleted.

To Exit and Re-enter Program Play

The program you have made is stored in memory. So, you can exit Program Play temporarily or re-enter Program Play unless you delete the program. To exit the program mode once, while the CD Player is stopped, press the PROGRAM button on the Unit or the PROGRAM/RANDOM button on the Remote Control to light off the “PRGM” indicator. By changing the source to the other (e.g. Tuner), the CD Player also exits Program Play mode. To re-enter Program Play mode, press the PROGRAM or PROGRAM/RANDOM button until the “PRGM” indicator lights up again.

English

Disc number Track number

SET

Program order number

Using the Remote Control

Press the numeric keys to directly enter the track number. Then, the program order number will be assigned from P-1.

• To delete the current program step, press the CANCEL button on the Unit.

• Even when the power is turned off (standby mode), the programmed tracks are not deleted. So, you can re-enter Program Play mode.

Page 18

Using the CD Player

Random Play

English

The tracks of all the CDs will play in no special order when you use this mode.

• To use Repeat Play for Random Play, press the REPEAT button to select “ALL” or “1” before starting playback. For details, see “Repeating Tracks”mentioned below.

In Stop mode, set the CD Player in Random

Play mode.

On the Unit

Press the RANDOM button to light the “RANDOM” indicator. At the same time, “RANDOM” appears on the display.

On the Remote Control

Press the PROGRAM/RANDOM button until the “RANDOM” appears on the display. The “RANDOM” indicator also lights up on the display. Each time you press the button, the display changes as follows: PROGRAM = RANDOM = Blank display (Normal Play) = (back to the beginning)

Press the CD

The tracks on all the CDs are played in random order.

To stop playing, press the 7 button. To skip a track during playback, press the ¢ button to

jump to the next track in the random sequence. To exit Random Play mode, while the CD Player is stopped, press the RANDOM button on the Unit or the PROGRAM/RANDOM button on the Remote Control again to light off the “RAN- DOM” indicator. Normal Play resumes.

button.

Tray Lock Function

In order to safely keep the CD in the CD Player, the tray can be electronically locked. When the electronic lock is on, the tray cannot be opened even if the CD Open/Close 0 button on the Unit is pressed.

Locking the Tray

Turn on the System and enter CD mode.

While pressing down the 7 button, press the

CD Open/Close

“LOCKED” appears on the display.

• If you try to open the tray by pressing the 0 button,

“LOCKED” appears on the display to let you know that the tray

has been locked.

Unlocking the Tray

Repeat above steps 1 and 2. “UNLOCKED” appears on the display.

Now, you can use the tray normally.

button on the Unit.

Repeating Tracks

You can repeat all tracks or individual track, as many times as you like.

Press the REPEAT button.

The Repeat indicator changes with each press of the button, as follows: ALL= 1CD = 1 = Blank display = (back to the beginning)

REPEAT ALL: In Normal Play mode, repeats all the tracks on

all the CDs. In Program Play mode, repeats all the tracks in the program. In Random Play mode, repeats all the tracks on all the CDs in random order.

REPEAT 1CD: Repeats all tracks on one CD. (Selectable in

REPEAT 1: Repeats one track. To stop playing, press the 7 button. Changing the source to the

other (e.g. Tuner) will also stop playing. To exit Repeat mode, press the REPEAT button until the Repeat indicator on the display goes out.

❏ Repeat mode remains in effect during the following Play Mode

changing: a. PROGRAM PLAY MODEÔNORMAL PLAY MODE

b. RANDOM PLAY MODE ÔNORMAL PLAY MODE c. PROGRAM PLAY MODEÔRANDOM PLAY MODE

Normal Play only)

Page 19

Using the Cassette Deck (Listening to a Tape)

3-CD

PLAY& EXCHANGE

STANDBY/ON

SLEEP

AUX

FM MODE

FM /AM

TAPE 3

CD1CD2CD

PROGRAM

REPEAT

/RANDOM

SOUND

KARAOKE

MODE

ACTIVE

ECHO

BASS EX.

TAPE

MUTING

A/B

TAPE

VOLUME

FADE

TAPE 3

TAPE A/B

0 EJECT

(Deck A)

COMPACT COMPONENT SYSTEM

STANDBY/ON

STANDBY

AUX

/ AM

PHONES

RECSTART

MIC

MICLEVEL

MIN MAX

EJECT EJECT

PLAY

CANCEL

/DEMO

TAPE

/STOPCDRECSTART

COMPU PLAY CONTROL

FULL - LOGIC CONTROL

SET

DUBBING

1BIT

DUALD/A

CONVERTER

PROGRAM

PANDOM

PRESET

TUNING

CLOCK

TAPE

/TIMER

A/B

CD SYNCHRO RECORDING

REPEAT

CD-R/RWPLAYBACK

SOUND

MODE

ACTIVE

BASSEX.

DISCSKIP

TAPE A/B

0 EJECT

REC / PLAY

(Deck B)

English

3: Tape indicator

Deck indicators

* When the System is in use, the display shows other items as well.

For simplicity, we show here only the items described in this section.

The Cassette Deck allows you to play, record, and dub audio tapes. ❏ Listening to type I tape is suitable for this Cassette Deck.

The use of tapes longer than 120 minutes is not recommended, since characteristic deterioration may occur and these tapes easily jam in the pinch-rollers and the capstans.

One Touch Play

By pressing the TAPE 3 button, the System will come on, and if a tape is in the deck, it will start to play. If no tape is loaded, “NO TAPE” appears on the display, the System will come on and wait for you to insert a tape, or select another function.

Playing a Tape

You can use either Deck A or Deck B at a time for playback.

Press the 0 EJECT part for the deck you

want to use. When the cassette holder opens, put a cas-

sette in, with the exposed part of the tape down, toward the base of the Unit.

The tape will travel from the left to right.

When both Deck A and Deck B contain a tape, the last deck to have a tape inserted is selected. The selected Deck is shown by the Deck indicator “A” or “B”. For example, when the Deck A is selected, the Deck indicator

“A” lights up.

• To change the deck, press the TAPE A/B button. Each time

you press the button, Deck A or Deck B is alternately selected.

Press the TAPE 3 button.

The Tape indicator (3) blinks on the display and the tape is played back. The Cassette Deck automatically stops when one side of the tape has finished playing.

To stop playing, press the 7 button. To remove the tape, stop the tape, and press the 0 EJECT part

to open the Cassette Holder.

To Fast-Wind A Tape

During playback or in Stop mode, press the ¡ (FF) button on the Unit to fast-wind the tape onto the right side of the cassette without playing. During playback or in Stop mode, press the 22 (REW) button on the Unit to fast-wind the tape onto the left side of the cassette without playing. During fast-winding the tape, the Tape indicator (3) goes out.

• The Cassette Deck automatically stops when one side of the tape has finished playing.

❏ During fast-winding the tape, you can change the tape travelling

direction by pressing the ¡ (FF) or 22 (REW) button.

Tape travelling direction

• If the cassette holder does not open, turn the System off,

then back on and press the 0 EJECT part again.

Close the cassette holder gently.

Page 20

Using the Cassette Deck (Recording)

English

TAPE A/B

TAPE 3

3-CD

STANDBY/ON

SLEEP

AUX

FM MODE

FM /AM

TAPE 3

CD REC START

CD1CD2CD

PROGRAM

REPEAT

/RANDOM

TAPE

A/B

TAPE

REC START/STOP

DUBBING

0 EJECT

SOUND MODE

ACTIVE

BASSEX.

KARAOKE

ECHO

MUTING

VOLUME

FADE

(Deck A)

COMPACT COMPONENT SYSTEM

STANDBY/ON

STANDBY

AUX

/ AM

PHONES

RECSTART

/STOPCDRECSTART

MIC

MICLEVEL

COMPU PLAY CONTROL

MIN MAX

EJECT EJECT

FULL - LOGIC CONTROL

PLAY

PLAY& EXCHANGE

REPEAT

1BIT

DUALD/A

CONVERTER

PROGRAM

PANDOM

SET

CANCEL

/DEMO

TAPE

DUBBING

PRESET

TUNING

CLOCK

TAPE

/TIMER

A/B

CD SYNCHRO RECORDING

CD-R/RWPLAYBACK

SOUND

BASSEX.

MODE

ACTIVE

DISCSKIP

PROGRAM

TAPE A/B

0 EJECT

REC / PLAY

(Deck B)

REC indicator

3: Tape indicator

REC

Deck indicators

* When the System is in use, the display shows other items as well.

For simplicity, we show here only the items described in this section.

Recording onto a cassette from any of the sound sources is simple. Just place a tape in Deck B, have the source ready, make one or two settings, and you’re ready to record. For each source, the procedure is a little bit different so we explain each separately. But first, here are a few things to make your recordings better.

Things To Know Before You Start Recording

❏❏❏❏ It may be unlawful to record or play back copyrighted

material without the consent of the copyright owner.

❏ The recording level, which is the volume at which the new tape

is being made, is automatically set correctly, so it is not affected by the VOLUME Control on the System. Also, it is not affected by adjusting the sound effects. Thus, during recording, you can adjust the sound you are actually listening to without affecting the recording level.

❏ Two small tabs on the back of the cassette tape, one for side A

and one for side B, can be removed to prevent accidental erasure or recording.

Adhesive tape

• At the start and end of cassette tapes, there is leader tape which cannot be recorded onto. Thus, when recording CDs, radio broadcasts, etc., wind on the leader tape first to ensure getting the beginning of the recording.

CAUTION:

• If a recording you make has excessive noise or static, the Unit may have been too close to a TV which was on during the recording. Either turn off the TV or increase the distance between the TV and the Unit.

❏ To record on a cassette with the tabs removed, you must cover

the holes with adhesive tape first.

❏ Type I tape can be used for recording.

Page 21

Standard Recording

This is the basic method for recording any source. The System also has special ways for recording CD to tape, and tape to tape, which save you time and effort, as well as give you some special effects. However, when you need to add a selection to a tape you have made, or are combining selections from several sources on one tape, use the method described below; just substitute the source you want into this procedure, such as a tape in Deck A, a CD, or the Tuner. You can also record from an external equipment with this procedure.

Using the Cassette Deck (Recording)

Insert a blank or erasable tape into the Deck

B and wind past the tape leader. Press the CD REC START button on the Unit.

“CD REC” appears on the display and the “REC” indicator lights up. Then, the System begins CD Synchro Recording and the tracks on the CD are recorded on the tape. When recording of the tracks of all CDs is finished, “CD REC FINISHED” scrolls on the display and the CD Player and Cassette Deck stop.

REC START

(When finished)

English

To Record Any Sound Source to Tape

Follow these steps to record from any sound source onto a tape in Deck B.

Insert a blank or erasable tape into the Deck

B and wind past the tape leader.

Tape travelling direction

Prepare the source, by, for example, tuning

in a radio station, loading CDs, or turning on connected equipment.

• For CD recording, see “CD Synchro Recording” mentioned below.

• For dubbing, see “Tape to Tape Recording (DUBBING)” described below.

Press the REC START/STOP button on the

Unit.

The “REC” indicator lights up and the System begins recording. The Tape indicator (3) blinks on the display.

• If the tab of the cassette tape on the Deck B is removed to prevent erasure or recording, "NO REC" will appear on the display.

To stop during recording, press the REC START/STOP button on the Unit, or press the 7 button.

Recording an AM Station to Tape (Beat Cut)

When recording an AM broadcast, beats may be produced which are not heard when listening to the broadcast. If this happens, press the PROGRAM button on the Unit to eliminate the beats.

Set to AM station and start recording.

Press the PROGRAM button on the Unit to

eliminate the beats.

Each time you press the button, the display changes as shown below: CUT 1= CUT 2 = (back to the beginning)

• If the tab of the cassette tape on the Deck B is removed to prevent erasure or recording, "NO REC" will appear on the display.

• After the CD Player has played the entire CD or all the programmed tracks, the tape automatically stops.

To stop at any time during the recording process, press the REC START/STOP button on the Unit or the 7 button. “CD REC FINISHED” scrolls on the display and the CD Player and Cassette Deck stop.

• When making SLEEP timer settings while doing CD Synchro recording, set enough time to allow for the CD to finish playing, otherwise the power will go off before recording is completed.

Tape to Tape Recording (DUBBING)

Recording from one tape to another is called dubbing. You can dub tapes simply, with just a single button.

Press the TAPE

7777

button.

Insert the source cassette you want to copy

from into Deck A for playback. Insert a blank or erasable cassette you want

to copy onto into Deck B for recording. Press the DUBBING button on the Unit.

Deck A and Deck B will start simultaneously and the "REC" indicator lights up. During dubbing, the Deck indicators "A" and "B" light up alternately.

• If no tape is inserted into Deck A, "NO TAPE" will appear on the display.

• If no tape is inserted into Deck B, "NO TAPE" will appear on the display.

To stop dubbing, press the REC START/STOP button on the Unit or the 7 button.

3333

button, and then press the

CD Synchro Recording

Everything on the CD goes onto the tape in the order it is on the CD, or according to the order you have set in a program.

Prepare CDs. (See page 12.)

Press the CD1-3 button (that you want to make recording), and then press the 7 button.

• If you want to record specific tracks only, you need to program the tracks beforehand. (See page 14.)

• During dubbing, you can hear sound effects through the speakers or headphones. However, the sound is dubbed without sound effects.

Page 22

English

Using an External Equipment

STANDBY/ON

SLEEP

FM MODE

AUX

FM /AM

AUX

CD1CD2CD

REPEAT

SOUND MODE

ACTIVE

BASSEX.

PROGRAM /RANDOM

KARAOKE

ECHO

TAPE

MUTING

A/B

TAPE

VOLUME

FADE

Listening to the External Equipment

You can listen to the external equipment such as MD recorder, cassette deck, or other auxiliary.

❏ First, make sure that the external equipment is properly connect-

ed to the System. (See page 6.)

Set the volume level to the minimum posi-

tion. Press the AUX button.

“AUX” appears on the display.

3-CD

PLAY& EXCHANGE

COMPACT COMPONENT SYSTEM

STANDBY/ON

STANDBY

AUX

/ AM

PHONES

MIC

MICLEVEL

MIN MAX

EJECT EJECT

PLAY

RECSTART

/STOPCDRECSTART

COMPU PLAY CONTROL

FULL - LOGIC CONTROL

SET

CANCEL

/DEMO

TAPE

DUBBING

1BIT

DUALD/A CONVERTER

PROGRAM

PANDOM

PRESET

TUNING

CLOCK

TAPE

/TIMER

A/B

CD SYNCHRO RECORDING

REPEAT

SOUND

BASSEX.

MODE

ACTIVE

CD-R/RWPLAYBACK

REC / PLAY

DISCSKIP

Start playing the external equipment.

Adjust the volume level to the level you want

listen to. Apply sound effects, if you wish.

• Press the ACTIVE BASS EX. to reinforce the bass sound.

• Select the Sound Mode. (See page 8.)

To exit AUX mode, select other source (e.g. Tuner).

• For operation of the external equipment, refer to its Instructions.

Page 23

Using the Timers

CD1CD2CD

PROGRAM

REPEAT

/RANDOM

SOUND

KARAOKE

MODE

ACTIVE

BASS EX.

ECHO

FM MODE

TAPE

A/B

FADE

MUTING

STANDBY/ON

SLEEP

AUX

FM /AM

TAPE

VOLUME

SLEEP

STANDBY

SET

PHONES

CLOCK/TIMER

DAILY Timer indicator

REC (Recording) Timer indicator

Timer indicator

3-CD

PLAY & EXCHANGE

COMPACT COMPONENT SYSTEM

STANDBY/ON

AUX

/ AM

REC START / STOPCD REC START

MIC

MIC LEVEL

MIN MAX

EJECT EJECT

PLAY

CANCEL

/ DEMO

TAPE

COMPU PLAY CONTROL

FULL - LOGIC CONTROL

SET

DUBBING

1 BIT

DUAL D/A CONVERTER

PROGRAM

PANDOM

PRESET

TUNING

CLOCK

TAPE

/TIMER

A / B

CD SYNCHRO RECORDING

REPEAT

SLEEP indicator

SLEEP DAILY REC

SOUND MODE

BASS EX.

ACTIVE

CD-R/RW PLAYBACK

REC / PLAY

English

DISC

SKIP

* When the System is in use, the display shows other items as well.

For simplicity, we show here only the items described in this section.

The timers lets you control recording and listening functions automatically. Three types of timers are available:

DAILY Timer Use this timer to set wake up everyday to music from any source, instead of an alarm clock.

REC (Recording) Timer

Unattended recording of radio broadcasts. You can set the starting time and length of the recording. SLEEP Timer Fall asleep and have your System turn off automatically after a certain length of time.

Setting the Clock

When you plug the AC power cord into the wall outlet, the time indication “0:00” blinks on the display. You can set the clock whether the System is on or off.

• The clock must be correctly set for the timers to work.

• Each setting step must be completed within approx. two

minutes. Otherwise, the setting is cleared and must be repeated from the beginning.

• The clock may gain or lose one to two minutes per month.

Using the Unit

Press the CLOCK/TIMER button.

The hour digit of the time indication blinks on the display.

• If the clock is already set and “0:00” is not blinking, press the CLOCK/TIMER button repeatedly until clock setting display appears on the display. In the clock setting display, the hour digits of the current clock blink on the display. Each time you press the CLOCK/TIMER button, the display

changes as follows: DAILY = ON TIME = REC = ON TIME = Clock setting display = Canceled = (back to the beginning)

Press the

Pressing the ¢ button moves the time forwards and pressing the 4 button moves it backwards. Holding down the button moves the hour rapidly.

Press the SET button.

The minute digits of the time indication blink on the display.

• To return to the hour setting, press the CANCEL button.

Press the

minute. Press the SET button.

“CLOCK OK” appears on the display. Then, the selected time is set and the seconds start counting from 0.

button to set the hour.

button to set the

CAUTION:

• If there is a power failure, the clock loses its setting immediately. “0:00” blinks on the display and the clock must be reset.

Page 24

Using the Timers

Setting the Daily Timer

English

Once you have set the Daily Timer, the timer will be activated at the same time every day. The Timer indicator ( ) on the display shows that the Daily Timer you have set is in effect. You can set the Daily Timer whether the System is turned on or off.

• Perform each setting within 30 seconds. Otherwise, setting will be cleared and the procedure must be repeated from the beginning.

• If you have made a mistake while setting the timer, press the CANCEL button on the Unit. However, this does not always cancel the current setting. If the CANCEL button does not work, press the CLOCK/TIMER button on the Unit repeatedly until the display returns to the original display, and start from the first step.

Using the Unit

Press the % STANDBY/ON button to turn on

the System.

Press the CLOCK/TIMER button until “ON

TIME” immediately after “DAILY” appears on the display.

At this time, “DAILY” indicator blinks and the Timer indicator ( ) lights up on the display. Each time you press the button, the display changes as follows: DAILY = ON TIME* = REC = ON TIME = Clock setting display = Canceled = (back to the beginning)

* : This item should be selected for the Daily Timer setting.

After 2 seconds, the System enters ON-time setting mode. The current ON time appears on the display and the hour digits blink.

2. Press the 4 or ¢ button to set the minute, then press the SET button.

DAILY

“OFF TIME” appears for 2 seconds, and the System enters OFF-time setting mode. The current OFF time appears on the display, and the hour digits blink.

After 2 seconds

Setting the OFF time (Example: 13:15).

1. Press the 4 or ¢ button to set the hour you want the System to come on, then press the SET button. The minute digits of the OFF time blink on the display.

2. Press the 4 or ¢ button to set the minute, then press the SET button.

The System enter Music Source Selecting mode and “TUNER FM” appears on the display.

DAILY

After 2 seconds

Setting the ON time (Example: 10:15).

1. Press the 4 or ¢ button to set the hour you want the System to come on, then press the SET button. The minute digits of the ON time blink on the display. Pressing the ¢ button moves the time forwards and pressing the 4 button moves it backwards. Holding down the button moves the time rapidly.

DAILY

Selecting the music source.

Press the 4 or ¢ button to select the music source you want to listen to, then press the SET button. Each time you press the 4 or ¢ button, the display changes as shown below: TUNER FM = TUNER AM = – CD – – – = TAPE = AUX = (back to the beginning) According to the music source you have selected, the next operation differs.

TUNER FM TUNER AM – CD – – – TAPE AUX

: Tunes in to the specified preset FM station.

: Tunes in to the specified preset AM station.

: Plays the specified track on the specified CD.

: Plays a tape in Deck A.

: Plays an external source.

Page 25

Using the Timers

Preparation for each music source:

Perform the following operation according to the music source you have selected. Then, the System enters Volume Setting mode.

When selecting TUNER FM or TUNER AM:

Press the 4 or ¢ button to select the preset station number, then press the SET button.

When selecting – CD – – –:

1. Press the 4 or ¢ button to select the disc number, then press the SET button. Each time you press the button the disc number changes as follows: – CD – – – = 1CD – – –= 2CD – – – = 3CD – – – = (back to the beginning)

2. Press the 4 or ¢ button to select the track number, then press the SET button. Please set the disc number to which you have listened at the last time. CD playback does not start if you select other disc number. Example: 2CD – 12 (Disc number 2, Track number 12) In this example, CD2 is selected as it was played back at the last time. If you select other CD number, the Daily Timer does not work at the set time.

When selecting TAPE:

Insert a cassette tape you want to play into Deck A.

When selecting AUX:

Prepare the external equipment so that it will turn on at the ON time set by the System. To allow this, the equipment should have the timer function.

Turning the Daily Timer On and Off

Once you have set the Daily Timer, it is stored in memory. So, the Daily Timer will be activated at the same time every day until it is canceled.

To cancel the Daily Timer temporarily:

Press the CLOCK/TIMER button on the Unit

repeatedly until the “DAILY” appears on the display.

Press the CANCEL button on the Unit.

The “DAILY” indicator goes out and “OFF” appears on the display. The Timer indicator ( ) and “DAILY” indicator go out and the Daily Timer is canceled temporarily.

To activate the cancelled Daily Timer:

Press the CLOCK/TIMER button on the Unit

repeatedly until the “DAILY” appears on the display.

The “DAILY” indicator blinks and the Timer indicator ( ) lights up on the dispaly.

Press the SET button on the Unit.

The “DAILY” indicator remains lit. Each setting already made appears on the display in the order of ON time, OFF time, music source and volume, and then the display returns to the original display.

English

Setting the volume level.

Press the 4 or ¢ button to select the volume level.

VOL – – – : The current volume level will be used. VOL-5, -10, or -15: When the timer is turned on, the Volume

will be automatically set to the selected level.

DAILY

Press the SET button.

The timer setting is completed, and the “DAILY” indicator stops blinking and remains lit. Each setting you have made appears on the display in the order of ON time, OFF time, music source and volume. Then, the display returns to the display before you set the Timer.

Press the

STANDBY/ON button to turn

%%%%

off the System.

The Timer indicator ( ) and “DAILY” indicator are lit on the display, showing that the Daily Timer is set to on.

To change the timer setting, repeat the setting procedure from the beginning.

When the timer ON-time comes:

The following operation will be automatically repeated every day.

• When the timer ON-time comes, and the System automatically turns on. The music source you have set is played. The Timer

indicator ( ) blinks during timer operation.

• When the timer OFF-time comes, “OFF” blinks on the display just before the OFF-time and the System automatically turns

off. Then, the Timer indicator ( ) remains lit on the display.

CAUTION:

• If the System is unplugged, or a power failure occurs, the timer setting will be lost in a few days. You will need to reset the clock first, then the timer.

Setting the REC (Recording) Timer

With the Recording Timer, you can make a tape of a radio broadcast automatically whether or not you are home.

• You can set the REC Timer whether the System is on or off.

• The volume level is automatically set to MIN when REC Timer is used.

• Perform each setting within 35 seconds. Otherwise, setting will be cleared and the procedure must be repeated from the beginning.

• If the System is already on when the timer ON-time comes, the Daily Timer does not work.

Page 26

Using the Timers

Using the Unit

You can set the time in the same way as for setting the Daily Tim-

English

er.

Insert a blank or erasable tape into the Deck

B and wind past the tape leader. Press the CLOCK/TIMER button until “ON

TIME” immediately after “REC” appears on the display.

Then, the "REC" indicator blinks on the display. Each time you press the button, the display changes as follows: DAILY = ON TIME = REC = ON TIME* = Clock setting display = Canceled = (back to the beginning)

* : This item should be selected for the REC Timer setting.

After 2 seconds, the System enters ON-time setting mode. The current ON time appears on the display and the hour digits blink.

After 2 seconds

Setting the ON time you want the System to

REC

turn on.

1. Press the 4 or ¢ button to set the hour, then press the

SET button.

2. Press the 4 or ¢ button to set the minute, then press the

SET button. “OFF TIME” appears for 2 seconds, and the System enters OFF-time setting mode. The current OFF time appears on the display, and the hour digits blink.

Setting the OFF time you want the System to

turn off.

1. Press the 4 or ¢ button to set the hour, then press the

SET button.

2. Press the 4 or ¢ button to set the minute, then press the

SET button. The System enter Preset Station Entering mode.

Select the preset station for recording.

1. Press the 4 or ¢ button to set the band (TUNER FM or

TUNER AM), then press the SET button.

2. Press the 4 or ¢ button to set the preset number, then

press the SET button. The REC indicator stops blinking and remains lit.

• Each setting you have made appears on the display in the order

of ON time, OFF time, radio band and the preset number.

When the timer ON-time comes:

• When the timer ON-time comes, the System automatically turns on. The station you have set is played. The Timer indica-

tor ( ) blinks during timer operation. To stop timer recording, press the 7 button.

• When the timer OFF-time comes, “OFF” blinks on the display just before the OFF-time and the System automatically turns off.

• The REC Timer works even if the System is turned on.

Turning the REC (Recording) Timer On and Off

Once you have set the REC Timer to record a source, the timer setting is stored in memory. So, though the REC Timer turns off once it is used, you can recall it at any time.

To cancel the REC Timer temporarily:

Press the CLOCK/TIMER button on the Unit

repeatedly until “REC” appears on the display.

Press the CANCEL button on the Unit.

“OFF” appears and the “REC” indicator goes out.

To activate the cancelled REC Timer:

Press the CLOCK/TIMER button on the Unit

repeatedly until “REC” appears on the display.

The “REC” indicator also blinks on the display.

Press the SET button on the Unit.

The “REC” indicator remains lit. Each setting already made appears on the display in the order of ON time, OFF time, and the preset number, and then the display returns to the original display.

CAUTION:

• If the System is unplugged, or a power failure occurs, the timer setting will be lost in a few days. You will need to reset the clock first, then the timer.

Press the

STANDBY/ON button to turn

%%%%

off the System, if necessary.

To change the timer setting, repeat the setting procedure from

the beginning.

Page 27

Using the Timers

Setting the SLEEP Timer

Use the Sleep Timer to turn the System off after a certain number of minutes when it is playing. By setting the Sleep Timer, you can fall asleep to music and know that your System will turn off by itself rather than play all night.

• You can only set the Sleep Timer when the System is on.

Using the Remote Control

During playback a source, press the SLEEP

button.

The “SLEEP” indicator starts blinking on the display.

Set the length of time you want the source to

play before shutting off.

Each time you press the SLEEP button, the time length changes as follows: 10 = 20 = 30 = 60 = 90 = 120 = Cancelled = (back to the beginning)

SLEEP

Wait for 5 seconds.

The “SLEEP” indicator stops blinking and remains lit, and the display returns to the original one before setting the Sleep Timer. The System is now set to turn off after the number of minutes you have set.

To Confirm the Sleep Time:

When the SLEEP button on the Remote Control is pressed, the remaining sleep time is displayed. Wait until the display returns to the original display.

To Cancel the SLEEP Timer Setting:

Press the SLEEP button on the Remote Control until the “SLEEP” indicator goes out on the display.

• Turning off the System also cancels the SLEEP Timer.

Timer Priority

Since each timer can be set independently, you may wonder what happens if the settings overlap. Here are the priorities for each timer:

❏ The REC Timer always has priority. This means that:

• If other timer is set to come on during a time when the REC Timer is operating, the other timer just won’t come on at all, so you will always get the entire program on a tape.

• If the REC Timer is set to come on while other timer is operating, the other timer will turn off just before the REC Timer is set to turn on, and the REC Timer will then take over.

❏ If the SLEEP Timer is set while DAILY Timer is operating, the

DAILY Timer settings are cancelled. However, if DAILY Timer is set to come on while the SLEEP Timer is operating, the SLEEP Timer setting will be cancelled and the System will use the settings from the DAILY Timer.

Example 1

Setting

ON OFF

REC Timer

OFF

SLEEP Timer

22:00 22:30 23:00

Operation

REC Timer

SLEEP Timer

Example 2

REC Timer

DAILY Timer

ON OFF

22:00 22:30

The REC Timer has priorty.

Setting

ON OFF

OFF

English

REC Timer

DAILY Timer

22:00 22:30 23:0021:30

Operation

ON OFF

22:3021:30

The REC Timer has priorty.

Page 28

Using the Microphone

English

KARAOKE

ECHO

CD1CD2CD

PROGRAM

REPEAT

/RANDOM

SOUND

KARAOKE

MODE

ACTIVE

BASS EX.

ECHO

FM MODE

TAPE

A/B

FADE

MUTING

STANDBY/ON

SLEEP

AUX

FM /AM

TAPE

VOLUME

VOLUME +, –

MIC jack

MIC LEVEL

Volume level, etc.

Karaoke indicator

3-CD

PLAY & EXCHANGE

COMPACT COMPONENT SYSTEM

STANDBY/ON

STANDBY

AUX

/ AM

PHONES

MIC

MIC LEVEL

MIN MAX

EJECT EJECT

PLAY

CANCEL

/ DEMO

REC START / STOPCD REC START

COMPU PLAY CONTROL

FULL - LOGIC CONTROL

SET

TAPE

DUBBING

1 BIT

DUAL D/A CONVERTER

PROGRAM

PANDOM

PRESET

TUNING

CLOCK

TAPE

/TIMER

A / B

CD SYNCHRO RECORDING

REPEAT

kHz

Echo indicator

SOUND MODE

BASS EX.

ACTIVE

CD-R/RW PLAYBACK

REC / PLAY

VOLUME

* When the System is in use, the display shows other items as well.

For simplicity, we show here only the items described in this section.

By attaching a microphone (not supplied) to the MIC jack, you can use the System for Karaoke or microphone mixing. You can also add an echo to the microphone’s sound.

CAUTION:

• Always set the MIC LEVEL control on the Unit to MIN when connection or disconnecting the microphone.

• When you will not be the microphone, keep the MIC LEVEL control set to MIN, and disconnect the microphone.

Singing Along with Karaoke

The Vocal Masking function lets you use regular tapes, CDs, or records as sources for Karaoke. When you select Karaoke mode, the lead vocal volume of the source is reduced, and you can replay it by singing into the microphones as the music plays.

Turn the MIC LEVEL control on the Unit to

MIN. Connect a microphone by plugging it into the

MIC jack. Press the KARAOKE button on the Remote

Control.

The Karaoke indicator ( ) comes on.

Adjust the volume, as you sing into the

microphone.

To adjust the volume, use the MIC LEVEL control and VOLUME control on the Unit or the VOLUME +,- button on the Remote Control.

To exit Karaoke mode, press the KARAOKE button on the Remote Control again. The Karaoke indicator ( ) will go off.

• Avoid using the following source as the playing source for Vocal Masking, since you cannot get the satisfactory results.

• Radio programs — a radio signal is not as reliable as

the signals coming from a tape or CD.

• Monaural sources.

• Poorly dubbed tapes.

• Sources recorded with dusts, strong echo, a chorus, or

only a few instruments.

Starts a source CD, tape, or other equipment.

Page 29

Using the Microphone

To Apply Digital Echo

Press the ECHO button on the Remote Control.

The Echo indicator ( ) comes on. To cancel the ECHO, press the ECHO button again. The Echo indicator goes off.

No echo is applied.

• To prevent howling and squealing (feedback) when using the microphone, adjust the volume properly. Also, try to avoid to pointing the microphone towards the speaker.

An echo is applied.

To Record Your Singing

Follow the steps in “Singing Along with

Karaoke” above. Prepare a tape and source, then press the

REC START/STOP button on the Unit.

For details, see “Standard Recording” on page 18.

Microphone Mixing

When using special Karaoke sources for Karaoke, use the following procedure.

Turn the MIC LEVEL control on the Unit to

MIN. Connect a microphone by plugging it into the

MIC jack. Start a source CD, tape, or other equipment.

Adjust the volume, as you sing into the

microphone.

To adjust the volume, use the MIC LEVEL control and VOLUME control on the Unit or the VOLUME +,- button on the Remote Control.

• When you want to apply echo to the microphone, press ECHO button on the Remote Control. The Echo indicator ( ) will come on.

Playing the Microphone Sound through the Speakers

You can directly output the microphone sound from the speakers.

Turn the MIC LEVEL control on the Unit to

MIN. Connect a microphone by plugging it into the

MIC jack. Adjust the volume, as you sing into the

microphone.

To adjust the volume, use the MIC LEVEL control and VOLUME control on the Unit or the VOLUME +,- button on the Remote control.

• When you want to apply echo to the microphone, press ECHO button on the Remote Control. The Echo indicator ( ) will come on.

Recording from the Microphone

Follow the steps in “Singing Along with

Karaoke” above. Prepare a tape and source, then press the

REC START/STOP button on the Unit.

For details, see “Standard Recording” on page 18.

English

To Record Microphone Mixing

Follow the steps in “Singing Along with

Karaoke” above. Prepare a tape and source, then press the

REC START/STOP button on the Unit.

For details, see “Standard Recording” on page 18.

Page 30

Care And Maintenance

Handle your CDs and tapes carefully, and they will last a long time.

English

Compact Discs

• Only CDs bearing these marks can be used with this System. However, continued use of irregular shape CDs (heart-

Recordable

ReWritable

shape, octagonal, etc.) can damage the System.

• Remove the CD from its case by holding it at the edges while pressing the case’s center hole lightly.

• Do not touch the shiny surface of the CD, or bend the CD.

• Put the CD back in its case after use to prevent warping.

• Be careful not to scratch the surface of the CD when placing it back in the case.

• Avoid exposure to direct sunlight, temperature extremes, and moisture.

• A dirty CD may not play correctly. If a CD does become dirty, wipe it with a soft cloth in a straight line from center to edge.

Cassette Tapes

• If the tape is loose in its cassette, take up the slack by inserting a pencil in one of the reels and rotating.

• If the tape is loose, it may get stretched, cut, or caught in the cassette.

• Do not touch the tape surface.

• Do not store the tape:

- In dusty places

- In direct sunlight or heat

- In moist areas

- On a TV or speaker

- Near a magnet

Cassette Deck

• If the heads, capstans, and pinch-rollers of the Cassette Deck become dirty, the following will occur:

- Loss of sound quality

- Discontinuous sound

- Fading

- Incomplete erasure

- Difficulty recording

• Clean the heads, capstans, and pinch-rollers using a cotton swab moistened with alcohol.

Capstan

Pinch-roller

CAUTION:

• Do not use any solvent (for example, conventional record cleaner, spray thinner, benzine, etc.) to clean a CD.

General Notes

In general, you will have the best performance by keeping your CDs and the mechanism clean.

• Store CDs in their cases, and keep them in cabinets or on shelves.

• Keep the System’s Top Cover closed when not in use.

Moisture Condensation

Moisture may condense on the lens inside the System in the following cases:

• After turning on heating in the room.

• In a damp room.

• If the System is brought directly from a

cold to a warm place. Should this occur, the System may malfunction. In this case, leave the System turned on for a few hours until the moisture evaporates, unplug the AC power cord, and then plug it in again.

Heads

• If the heads become magnetized, the Unit will produce noise or lose high frequencies.

• To demagnetize the heads, turn off the Unit, and use a head demagnetizer (available at electronics and record shops).

Page 31

Troubleshooting

• If you are having a problem with your System, check this list for a possible solution before calling for service.

• If you cannot solve the problem from the hints given here, or the System has been physically damaged, call a qualified person, such as

your dealer, for service.

Symptom Possible Cause Action

No sound is heard. • Connections are incorrect, or loose.

• Headphones are connected.

Poor radio reception • The antenna is disconnected.

• The AM Loop Antenna is too close

to the System.

• The FM Wire Antenna is not properly extended and positioned.

The disc tray does not open.

The CD skips. The CD is dirty or scratched. Clean or replace the CD. (See page 27.) The CD does not play. The CD is upside down. Put the CD in with the label side up. The cassette holder cannot be opened. During tape playing, the power cord

Unable to record. Cassette record protect tabs are re-

Unable to operate the Remote Control. • The path between the Remote Con-

Operations are disabled. The built-in microprocessor has mal-

• The AC power cord is not plugged in.

• Tray is locked.

was unplugged.

moved.

trol and the sensor on the Unit is blocked.

• The batteries have lost their charge.

functioned due to external electrical interference.

• Check all connections and make corrections. (See pages 4 to 6.)

• Disconnect the headphones.

• Reconnect the antenna securely.

• Change the position and direction of

the AM Loop Antenna.

• Extend FM Wire Antenna to the best reception position.

• Plug the AC power cord.

• Unlock the tray. (See page 15.)

Plug in the power cord, and turn on the System.

Cover holes on back edge of cassette with tape.

• Remove the obstruction.

• Replace the batteries.

Unplug the System then plug it back in.

English

Specifications

Amplifier

Output Power

CA-MXK30 60 W per channel, min. RMS, driven into

6 Ω at 1kHz, with no more than 10% to-

CA-MXK10 30 W per channel, min. RMS, driven into

Input Sensitivity/Impedance (1 kHz)

AUX IN 300 mV/50 kΩ

Speaker terminals 6 - 16 Ω

Cassette Deck Section

Frequency Response

Type I (NORMAL) 63 - 12 500 Hz

Wow And Flutter 0.15% (WRMS)

CD Player

CD Capacity 3 CDs

Dynamic Range 85 dB

Signal-To-Noise Ratio 90 dB

Wow And Flutter Unmeasurable

FM Tuner

Tuning Range

AM Tuner

Tuning Range

Dimensions CA-MXK30 CA-MXK10

CA-MXK30 CA-MXK10

tal harmonic distortion (IEC 268-3)

6 Ω at 1kHz, with no more than 10% total harmonic distortion (IEC 268-3)

Phones 32 Ω - 1 kΩ,

15 mW/ch output into 32 Ω

Tuner

87.50 - 108.00 MHz (at AM 9 kHz channel space)

87.5 - 108.0 MHz (at AM 10 kHz channel space)

531 - 1 710 kHz (at 9 kHz channel space) 530 - 1 710 kHz (at 10 kHz channel space)

Unit

270 mm ✕ 305 mm ✕ 430 mm (W/H/D) 270 mm ✕ 305 mm ✕ 386 mm (W/H/D)

Mass

Approx. 7.5 kg Approx. 6.6 kg

Speaker Specifications (each unit)

SP-MXK30

Type 3-way bass-reflex type

Speaker Unit Woofer: 13.5 cm cone ✕ 1

Mid: 5 cm cone ✕ 1 Tweeter: 2 cm dome ✕ 1

SP-MXK10

Type 3-way bass-reflex type

Speaker Unit Woofer: 13.5 cm cone ✕ 1

Mid: 5 cm cone ✕ 1 Tweeter: 2 cm dome ✕ 1

Power Handling Capacity

SP-MXK30 60 W SP-MXK10 30 W

Impedance 6 Ω

Frequency Range 45 - 22,000 Hz

Sound pressure level 88 dB/wm

Dimensions 225 mm ✕ 305 mm ✕ 245 mm (W/H/D) SP-MXK30 Mass Approx. 3 kg SP-MXK10 Mass Approx. 2.7 kg

Accessories

AM Loop Antenna (1) Remote Control (1) Batteries R6P (SUM-3)/AA (15F) (2) FM Wire Antenna (1) AC Plug Adaptor (1)

Power Specifications

Power Requirements AC 110/127/220/230 - 240 V , adjust-

able with the voltage selector, 50/60 Hz

Power Consumption

CA-MXK30 105 W (power on mode)

10 W (in Standby mode)

CA-MXK10 65 W (power on mode)

8 W (in Standby mode)

Design and specifications are subject to change without notice.

Page 32

Mains (AC) Line Instruction (not applicable for Europe, U.S.A., Canada, Australia, and U.K.)

IMPORTANT for mains (AC) line

BEFORE PLUGGING IN, do check that your mains (AC) line voltage corresponds with the position of the voltage selector switch provided on the outside of this equipment and, if different, reset the voltage selector switch, to prevent from a damage or risk of fire/electric shock.

EN, CH 0402NNMCREBET

VICTOR COMPANY OF JAPAN, LIMITED

JVC MX-K30 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Introduction

Table of Contents

Getting Started

Basic Operations

Using the Tuner

Using the CD Player

Using the Cassette Deck (Listening to a Tape)

Using the Cassette Deck (Recording)

Using an External Equipment

Using the Timers

Using the Microphone

Care And Maintenance

Troubleshooting

Specifications