Enter below the Model No. and Serial No.
which are located either on the rear, bottom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
LVT0686-003A
[US]
Warnings, Cautions and Others
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
IMPORTANT FOR LASER PRODUCTS /
REPRODUCTION OF LABELS /
CLASSIFICATION LABEL, PLACED ON EXTERIOR SURFACE
1
1
Caution –– switch!
Disconnect the mains plug to shut the power off completely. The
switch in any position does not disconnect the mains line. The power
can be remote controlled.
WARNING LABEL, PLACED INSIDE THE UNIT
2
2
1. CLASS 1 LASER PRODUCT
2. CAUTION: Invisible laser radiation when open and interlock failed
or defeated. Avoid direct exposure to beam.
3. CAUTION: Do not open the top cover. There are no user serviceable parts inside the Unit; leave all servicing to qualified service
personnel.
G-1
Caution: Proper Ventilation
15 cm
15 cm
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
1 Front:No obstructions and open spacing.
2 Sides/ Top/ Back: No obstructions should be placed in the areas shown by the dimensions below.
3 Bottom:Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of 10 cm or more.
Front viewSide view
15 cm
3-CD
PLAY & EXCHANGE
MX-K3
1 BIT
DUAL D/A
CONVERTER
PRESET
CANCEL SET
O
V
/ DEMO
TUNNIG
CD
TAPE
CD
REC START
/STOP REC STARTDUBBING
CLOCK
TAPE
/TIMER
A/B
FULL - LOGIC CONTROL CD SYNCHRO RECORDING
CD-R/RW PLAYBACK
ACTIVE
BASS EX.
P
K
O
C
P
O
R
SOUND
MODE
E
M
U
L
C
C
I
L
S
A
S
DISC SKIP
1 cm1 cm
CD CONTROL
1
3
CD
CD 2CD
EJECT
REC/PLAY
B
15 cm
10 cm
15 cm
STANDBY
PHONES
COMPACT COMPONENT SYSTEM
STANDBY/ON
AUX
REPEAT PROGRAMRANDOM
MIC MIC
VOL
MAXMIN
EJECT
PLAY
A
FM/AM
COMPU PLAY CONTROL
ACTIVE BASS EXTENSION
SAFETY PRECAUTIONS
Prevention of Electric Shocks, Fire Hazards and Damage
1. Do not use this apparatus in a bathroom or places with water. Also
do not place any containers filled with water or liquids (such as
cosmetics or medicines, flower vases , potted plants, cups , etc.) on
top of this apparatus.
2. Do not block the ventilation openings or holes.
(If the ventilation openings or holes are blocked by a ne wspaper or
cloth, etc., the heat may not be able to get out.)
3. Do not place any naked flame sources, such as lighted candles, on
the apparatus.
4. When discarding batteries, environmental problems must be considered and local rules or laws governing the disposal of these batteries must be followed strictly.
G-2
Introduction
Thank you for purchasing the JVC Compact Component System.
We hope it will be a valued addition to your home, giving you years of enjoyment.
English
Be sure to read this instruction manual carefully before operating your new stereo system.
In it you will find all the information you need to set up and use the system.
If you have a query that is not answered by the manual, please contact your dealer.
Features
Here are some of the things that make your System both powerful and simple to use.
❏The controls and operations have been redesigned to make them very easy to use, freeing you to just enjoy the
music.
• With JVC’s COMPU PLAY you can turn on the System and automatically start the Radio, Cassette Deck, or
CD Player with a single touch.
❏The great SEA (Sound Effect Amplifier) effects Rock, Pop and Classics are provided.
❏The Active Bass EX. (Extension) circuitry faithfully reproduces low frequency sounds.
❏A 45-station preset capability (30 FM and 15 AM ) in addition to auto-seek and manual tuning.
❏CD changer function can operate 3 discs.
• Discs can be changed during play using the Carrousel tray (rotational tray).
• Continuous, random or program play of 3 discs.
❏Two Decks enabling tape dubbing.
❏You can use conventional tapes and CDs for Karaoke with the voice masking system. With an optional microphone, you can replace the
lead singer’s voice on your favorite songs with your own.
• Digital Echo applied to your voice through the microphone gives you a professional sound.
❏Timer functions; Daily Timer, REC (Recording) Timer, and Sleep Timer.
❏You can connect various external units, such as an MD recorder.
❏The CD player can play back a CD-R and CD-RW.
How This Manual Is Organized
• Basic information that is the same for many different functions - e.g. setting the volume - is given in the section “Basic Operations”,
and not repeated under each function.
• The names of buttons/controls and display messages are written in all capital letters: e.g. FM/AM, “NO DISC”.
• If the button names on the Unit and the Remote Control are the same, the description on where the button is used will be omitted.
• System functions are written with an initial capital letter only: e.g. Normal Play.
Use the table of contents to look up specific information you require.
We have enjoyed making this manual for you, and hope it serves you in enjoying the many features built into your System.
IMPORTANT CAUTIONS
Installation of the System
1
• Select a place which is level, dry and neither too hot nor too cold. (Between 5°C and 35°C or 41°F and 95°F.)
• Leave sufficient distance between the System and a TV.
• Do not use the System in a place subject to vibrations.
Power cord
2
• Do not handle the power cord with wet hands!
• Some power is always consumed as long as the power cord is connected to the wall outlet.
• When unplugging the System from the wall outlet, always pull the plug, not the power cord.
Malfunctions, etc.
3
• There are no user serviceable parts inside. In case of system failure, unplug the power cord and consult your dealer.
• Do not insert any metallic object into the System.
Reinforcing the Bass Sound (ACTIVE BASS EX.)................................................................................8
Selecting the Sound Mode (SOUND MODE).........................................................................................8
Entering the Number with the Remote Control (Numeric Keys)............................................................8
Using the Tuner.............................................................................................................9
Tuning In a Station.................................................................................................................................. 9
To Change the FM Reception Mode..................................................................................................... 10
Using the CD Player....................................................................................................11
To Load CDs ............................................................................................ ....................................... ...... 12
To Unload CDs............................................................................................ ....................................... ...12
Basics of Using the CD Player-Normal Play......................................................................................... 13
Programming the Playing Order of the Tracks......................................................................................14
Random Play.......................................................................................................................................... 15
Using the Cassette Deck (Listening to a Tape) ........................................................16
Playing a Tape....................................................................................................................................... 16
Using the Cassette Deck (Recording) ......................................................................17
Standard Recording ...............................................................................................................................18
CD Synchro Recording.......................................................................................................................... 18
Tape to Tape Recording (DUBBING)................................................................................................... 18
Using an External Equipment ....................................................................................19
Listening to the External Equipment..................................................................................................... 19
Using the Timers .........................................................................................................20
Setting the Clock ...................................................................................................................................20
Setting the Daily Timer .........................................................................................................................21
Setting the REC (Recording) Timer...................................................................................................... 22
Setting the SLEEP Timer ......................................................................................................................24
Make sure that you have all of the following items, which are supplied with the System.
AM Loop Antenna (1)
Remote Control (1)
Batteries (2)
FM Wire Antenna (1)
AC Plug Adaptor (1)
If any of these items are missing, contact your dealer immediately.
Set the VOLTAGE SELECTOR Switch
To avoid damaging the System, set the voltage before plugging in the System.
Set the correct voltage for your area with the VOLTAGE SELECTOR switch on the back of the Unit. Use a screwdriver to rotate the selector
so the number the voltage mark is pointed at is the same as the voltage.
Voltage mark
How To Put Batteries In the Remote Control
Match the polarity (+ and –) on the batteries with the + and – markings in the battery compartment.
R6P(SUM-3)/AA(15F)
CAUTION:
• Handle batteries properly.
❏To avoid battery leakage or explosion:
• Remove batteries when the Remote Control will not be used for a long time.
• When you need to replace the batteries, replace both batteries at the same time with new ones.
• Do not use an old battery with a new one.
• Do not use different types of batteries together.
3
Getting Started
Using the Remote Control
The Remote Control makes it easy to use many of the functions of the System from a distance of up to 7m (23 feet) away.
You need to point the Remote Control at the remote sensor on the System’s front panel.
3-CD
Remote sensor
COMPACT COMPONENT SYSTEM
STANDBY/ON
STANDBY
PHONES
AUX
MIC MIC
A
REPEAT PROGRAM RANDOM
VOL
MAXMIN
EJECT
PLAY
PLAY & EXCHANGE
MX-K3
CANCEL SET
/ DEMO
TUNNIG
CD
TAPE
FM/AM
CD
REC START
/STOP REC START DUBBING
CLOCK
/TIMER
COMPU PLAY CONTROL
ACTIVE BASS EXTENSION
FULL - LOGIC CONTROL CD SYNCHRO RECORDING
TAPE
A/B
CD-R/RW PLAYBACK
1 BIT
ACTIVE
DUAL D/A
CONVERTER
BASS EX.
PRESET
E
M
U
L
O
V
P
K
O
C
P
O
R
SOUND
MODE
C
C
L
I
A
S
S
DISC SKIP
CD CONTROL
1
3
CD
CD 2CD
EJECT
REC/PLAY
B
CAUTION:
• Make all connections before plugging the System into an AC power outlet.
Connecting the FM Antenna
Using the Supplied Wire Antenna
FM wire antenna (supplied)
English
ANTENNA
AM
EXTFM75
AM
LOOP
FM
GNDGND
Using an FM 75-Ohm Antenna Cable (not Supplied)
If reception is poor, connect the outside antenna.
Strip vinyl shield from cut line,twist wire
core.
Outdoor FM antenna cable (not supplied)
Extend the supplied FM
Wire Antenna horizontally.
• Before attaching a 75 ohm coaxial lead (the kind with a round wire going to an outdoor antenna), disconnect the supplied
FM Wire Antenna.
4
Getting Started
Connecting the AM Antenna
English
Rear Panel of the Unit
AM loop antenna (Supplied)
ANTENNA
AM
EXTFM75
AM
LOOP
GNDGND
• Even when connecting an outside AM antenna, keep the indoor AM loop connected.
FM
AM antenna wire (not supplied)
If reception is poor, connect the outside antenna.
Turn the loop until you
have the best reception.
Attach the AM loop to its
base by snapping the
tabs on the loop into the
slot in the base.
CAUTION:
• To avoid noise, keep antennas away from the System, the connecting cord and the AC power cord.
Connecting the Speakers
1. Open each of the terminals to connect the speaker wire leads.
2. Connect the speaker cords to the Speaker terminals of the Unit.
Connect the red (+) and black (–) wires of the right side speaker to the red (+) and black (–) terminals marked RIGHT on the System.
Connect the red (+) and black (–) wires of the left side speaker to the red (+) and black (–) terminals marked LEFT on the System.
3. Close each of the terminals to securely connect the cords.
Right side (rear view)Left side (rear view)
Red
Black
CAUTION:
SPEAKER IMPEDANCE 6 16 OHMS.
SPEAKERS
RIGHT
LEFT
Red
Black
CAUTIONS:
• A TV may display irregular colors if located near the speakers. If this happens, set the speakers away
from the TV.
• Use speakers with the correct impedance only. The correct impedance is indicated on the rear panel.
5
Getting Started
Connecting External Equipment
Connect a signal cord (not supplied) between the System’s AUX-IN terminals and the output terminals of the external MD recorder, tape
deck, etc.
You can then listen to the external source through the System.
AUX IN
LEFT
RIGHT
Signal cord (not supplied)
Pin-plug x 2Pin-plug x 2
MD recorder, tape deck, etc. (not supplied)
Connecting to the Wall Outlet
Plug the AC power cord into the wall outlet.
Now, your System is at your command!
DEMO Mode
When the System is connected to the wall outlet, a DEMO mode displaying some of the system’s features automatically starts.
To turn the DEMO display off,
To turn the DEMO display on,
press any of the operation buttons. The DEMO display automatically stops.
press the DEMO button on the Unit for more than 2 seconds.
CANCEL
/ DEMO
(For 2 seconds)
English
• The DEMO display will automatically turn on again if no button operation is made for 2 minutes. To cancel this auto DEMO
display function, press the CANCEL button on the Unit during DEMO display.
COMPU Play
JVC’s COMPU PLAY feature lets you control the most frequently used System functions with a single touch.
With One Touch Operation you can play a CD, a tape, turn on the radio, or listen to an external equipment with a single press of the play
button for that function. One Touch Operation turns the power on for you, then starts the function you have specified. If the System is not
ready (no CD or tape in place), the System still powers on so you can insert a CD or tape.
How One Touch Operation works in each case is explained in the section dealing with that function.
The COMPU PLAY buttons are:
On the Unit
CD 6 button
FM/AM button
TAPE 3 button
AUX button
CD1, CD2 and CD 3 buttons
CD Open/Close 0 button
On the Remote Control
CD 6 button
FM/AM button
TAPE 3 button
AUX button
CD1, CD2 and CD 3 buttons
6
Basic Operations
CAUTION:
)
English
Numeric
keys
SOUND
MODE
ACTIVE
BASS EX.
RM-SMXK3U REMOTE CONTROL
123
456
789
10 +10
FM MODE
CD1CD2CD3CD
PROGRAM
REPEAT T APE A/B
/RANDOM
COMPU PLAY
CONTROL
KARAOKE
SOUND
MODE
ACTIVE
VOLUME
BASS EX.
STANDBY/ON
SLEEP
AUX
FM /AM
TAPE
ECHO
FADE
MUTING
%
Display
STANDBY indicator
%
PHONES
VOLUME +,–
FADE MUTING
COMPACT COMPONENT SYSTEM
STANDBY/ON
STANDBY
PHONES
AUX
REPEAT PROGRAM RANDOM
MIC MIC
MAXMIN
EJECT
A
MX-K3
CANCEL SET
/ DEMO
CD
TAPE
FM/AM
REC START
VOL
PLAY
/STOP REC START DUBBING
COMPU PLAY CONTROL
ACTIVE BASS EXTENSION
FULL - LOGIC CONTROL CD SYNCHRO RECORDING
Various information
Level bar
Status bar (Indicates various statuses.)
* When the System is in use, the display shows other items as well.
For simplicity, we show here only the items described in this section.
PLAY & EXCHANGE
TUNNIG
CD
CLOCK
/TIMER
3-CD
TAPE
A/B
BASS
S.MODE
1 BIT
DUAL D/A
CONVERTER
PRESET
ACTIVE
BASS EX.
O
E
M
U
L
O
V
R
EJECT
REC/PLAY
BASS indicator
Sound Mode indicator
CD-R/RW PLAYBACK
K
C
SOUND
MODE
C
C
L
I
A
S
S
DISC SKIP
CD CONTROL
1
CD
CD 2CD
B
ACTIVE
P
O
P
BASS EX.
SOUND MODE
VOLUME
3
Turning the Power On and Off
Turning the System On
Press the
1
The display comes on and “WELCOME” is displayed once.
The STANDBY indicator goes out.
The System comes on ready to continue in the mode it was in
when the power was last turned off.
• For example, if the last thing you were doing was listening
to a CD, you are now ready to listen to a CD again. If you
wish, you can change to another source.
• If you were listening to the Tuner last, the Tuner comes on
playing the station it was last set to.
Turning the System Off
Press the % button again.
1
“GOOD BYE” is displayed and the display goes out, except
for the clock display. The STANDBY indicator lights up. (The
display is dimmed.)
• Some power is always consumed even though power is
turned off (called Standby mode).
• To switch off the System completely, unplug the AC power
cord from the wall outlet. When you unplug the AC power
cord, the clock will be reset to 0:00 immediately.
%
STANDBY
STANDBY
_
button.
STANDBY/ON
STANDBY/ON
STANDBY/ON
or
STANDBY/ON
or
Adjusting the Volume
Turn the VOLUME control on the Unit clockwise to increase the
volume or turn it counterclockwise to decrease the volume.
Press the VOLUME + button on the Remote Control to increase
the volume or press the VOLUME – button to decrease the volume.
You can set the volume level to MIN, 1-31, or MAX.
• DO NOT turn on the System and/or start playing
any source without first setting the VOLUME
control to minimum, as a sudden blast of sound
could damage your hearing, speakers and/or
headphones.
For private listening
Connect a pair of headphones to the PHONES jack. No sound
comes out of the speakers.
Be sure to turn down the volume before connecting or putting on
headphones.
7
Loading...
+ 22 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.