JVC M-3030 Service manual

Page 1

No. 2420 MAY, 1977

Page 2

Contents

Page
1. Specificat ions . 2
2. Precautio ns in Servicing · 2
3. Removal of Covers and Panels . 3
4. Main Part s Location and Part Numbers
4-(1) Top View . 4
4-(2) Bottom View . 4
5. Exploded Views and Parts List
5-(1) Top and Rear Panels · 5
5-(2) Heat Sink and P.C. Board Ass'y · 6
5-(3) Heat Sink and Power Transistors · 7
5-(4) Bottom Plate · 7
6. Adjustme ent Procedures
6-(1) Center Voltage • 8
6-(2) Idling Current • 8
7. Wiring Di agram of All P.C. Board Assemblies . 9
8. Printed C ircuit Board Ass'y and Parts List
8-(1) TXX-45 L.E.D. and Connector P.C. Board Ass'y . 10
8-(2) TPS-78 Class-A Power Supply P.C. Board Ass'y . 11
8-(3) TPS-79 Class-B Power Supply P.C. Board Ass'y . 13
8-(4) TPS-86 AC Fuse P.C. Board Ass'y . 14
8-(5) TAD-181 Driver Amp. & Protector P.C. Board Ass'y . 15
8-(6) TAD-182 Driver Amp. P.C. Board Ass'y . 18
9. Accessor ies List . 20
10. Packing I Materials and Part Numbers . 20
11. Transisto r Lead Identification . 21
12. Parts Lis t with Specified Numbers for Designated Areas . 21
13. Schematic Diagram
14. Schemat c Diagrams for Designated Areas . 23
Page 3

1. Specifications

Transistor & Diode
Output Power (Continuous)
(both channels driven)
Total Harmonic Distortion (8 Ω)
: 2 FETs (Dual packa
100 W + 100 W (8 S
130 W + 130 W (4 S
ge), 41 Transistors, 13 Diodes
2)
2)
(20 Hz – 20 kHz both channels : Rated output 0.05 % or less
driven) 50 W output 0.01 % or less
1 W output 0.01 % or less
(1 kHz both channels driven) : Rated output 0.007 % or less
Intermodulation Distortion (8 \Omega)
(SMPTE, both channels driven) : Rated output 0.05 % or less
50 W output 0.03 % or less
1 W output 0.03 % or less
Power Bandwidth ·
(IHF both channels driven) : 5 Hz – 30 kHz 0.02 % T.H.D. at -3 dB output power
5 Hz – 100 kHz 0.3 % T.H.D. at -3 dB output power
Frequency Response : DC – 100 kHz +0 dB, -1 dB from DIRECT input termina
Subsonic Filter : 18 Hz (-6 dB/oct) from SUBSONIC input terminal
Input Sensitivity/Impedance : 1.0 V/more than 50
Signal-to-Noise Ratio : 116 dB (IHF, A net work, input short)
Damping Factor : More than 75 (20 H z – 20 kHz)
Output Impedance : 4 – 16 Ω

2. Precautions in Servicing

Notes:

• Both left and right channels employ the same class-B power supply circuit board (TPS-79). Identifications of the circuit board in the diagram are provided by prefix "L" for the left channel and "R" for the right channel, as shown in the example below.

Example: D501 for the left channel: L-D501

D501 for the right channel: R-D501

  • Check ventilation carefully when a great deal of heat is generated. If the amplifier is installed on a dead-end rack, heat will accumulate and result in a reduction in the service life of the parts. Maintain a clearance of at least 5 cm on the top to assure sufficient air flow.
  • Do not reverse the L and R SUBSONIC and DIRECT terminals since neither channel will function properly if the connections are incorrect. Be sure the L and R leads are properly connected to the correct input terminals.
  • Do not mount the amplifier with the rear panel removed. The power cord may bend and become disconnected where it exits from the bottom of the amplifier.
Page 4

3. Removal of Covers and Panels

Procedure
1. Side Panel

Remove four screws 1 on each side. Remarks:

  • First remove the side panels to permit the parts to be removed.
  • Be sure to follow the order of steps given here.
2. P.C. Board Cover

Remove the two screws(2), then slide back and lift up. Remark:

The front panel can not be dismounted until the circuit board cover is removed.

3. Front Panel

Remove screw(3) from above and two screws(4) from below, then pull the front panel out to the front. Remark:

The driver circuit board and power transistors can now be removed.

4. Bottom Cover

Remove the screws (5).

Remark:

Then remove the circuit boards and other parts.

-3-

Page 5

4. Main Parts Location and Part Numbers

4-(1) Top View

4-(2) Bottom View

Page 6

5. Exploded Views and Parts List

5-(1) Top and Rear Panels

Item No. Part Number Rating Description Q'ty
1 E10152-002 Heat Sink 1
2 E22210-003 Front Panel | 1
3 SBSB3008M Tapping Screw 46
4 E10152-001 Heat Sink | 1
5 E22204-001 P.C. Board Cover 1
6 E22208-001 Side Panel 2
7 E61423-001 Push Knob 1
8 E61527-001 Knob 2
9 QVF1A2B-015V 100 kΩ (B) Variable Resistor 2
10 E22206-001 Condenser Cover 1
11 SDSB3012M Tapping Screw 8
12 E61420-001 Control Bracket 1
13 E03043-40B Pin Jack Ass'y 1
14 E48729-001 Plastic Rivet 6
15 E34781-001 Stay Bracket 1
16 E03619-001 Ground Terminal 1
17 (See page 21) Power Cord 1
18 E03709-001 Free Up Belt 1
19 E03611-4B Power Transformer 2
20 E47957-007 Escutcheon
21 QSP2111-012 Power Switch
22 E22203-003 Rear Panel 1
Page 7

Item No. Part Number Rating Description Qʻty
1 SBSB3012M Tapping Screw 2
2 E10152-002 Heat Sink 1
3 E10152-001 1
4 E34781-002 Stay Bracket 1
5 E61537-001 Heat Sink 4
6 2SB536 (L, M)
2SB507V (D, E)
Si. Transistor X623, 624,
" X702
3
7 SPSP3005MS Screw 8
9 TAD-182A Driver Driver Circuit
P.C. Board Ass'y
1
10 E48688-001 Connect Pin 45
11 E10139-001 Chassis Base Ass'y 1
12 SSSB3008M Tapping Screw 12
13 E34781-001 Stay Bracket 1
14 TAD-181B Driver & Protector Driver & Protector
P.C. Board Ass'y
1
15 E48729-001 Plastic Rivet 6
16 E34779-001 Support 1
17 SBSB3008M Tapping Screw 46
18 E34780-001 Support 1
19 2SC853 (L) Si. Transistor X619, 620 2
20 E50670-005 Wire Clamp 4
Page 8

5-(3) Heat Sink and Power Transistors

Item No. Part Number Rating Description Q'ty
1 E10152-001 Heat Sink 1
2 2SB612V (B, C) Transistor 4
3 LPSP3020NS Ass'y Screw 16
4 E03624-001 Transistor Socket 8
5 2SD582V (B, C) Transistor 4
6 E10152-002 Heat Sink 1
7 2SB536 (L, M) Transistor

5-(4) Bottom Plate

Page 9

6. Adjustment Procedures

6-(1) Center Voltage (See Fig. 12)

  • 1. Adjust R631 (or R632) to the midpoint before turning power on.
  • Connect a voltmeter providing accurate voltages readings below 10 mV between test point C and the chassis of TAD-182 and 181 respectively, with the plus lead to point C and minus lead to the chassis. Then turn power on.
  • 3. Turn R631 (or R632) little by little until the voltmeter reads 0 V.

Note: Speaker terminals may be used in place of test point C.

6-(2) Idling Current (See Fig. 13)

  • 1. Turn the R645 (or 646) fully in the opposite direction to the arrow.
  • Five to six minutes after turning power on, connect the voltmeter minus leads to test point C (or the speaker plus terminal) and the plus lead to test point E (of both TAD-182 and 181) then slowly turn the resistor in the direction of the arrow until the voltmeter reads 10 mV.
  • 3. Check that the voltage between test point C (or the speaker plus terminal) and test point D is approximately 10 mV. Reverse the voltmeter polarity and check that the voltage between test point C (or the speaker plus terminal) and test point A is nearly equal to that between test point C and test point B.
  • 4. After adjusting TAD-182 and 181, recheck the channel first adjusted. If it is out of adjustment, repeat the adjustment. (Adjustment repeated two or three times alternately for L and R is sufficient.)
  • 5. The idle current has now been adjusted to 20 mA (13–32 mA).
Test point ۵ C D E Power transistor Adjust to:
Center voltage 0 0 mV
0 0 X625 (or X626)
0 0 X629 (or X630
Idling current 0 0 X627 (or X628) 10 m V
0 0 X631 (or X632)

Page 10

ransistor 6 6 ê _____

M-3030 No. 2420

Page 11

8 Printed Circuit Board Ass'y and Parts List

8-(1) TXX-45 L.E.D. and Connector P.C.Board Ass'y

Fig. 15

Capacitors Item No. Description Part Number Rating C801 QFM42AK-104 0.1 μF 100 V Mylar C802 QFM42AK-104 C803 OFM42AK-104 C804 OFM42AK-104 C805 OFM42AK-473 0.047 μF 100 V C806 OFM42AK-473 C807 CF93MMA2E-105K 1μF 250 V Metalized Mylar C808 CF93MMA2E-105K C809 CF93MMA2E-105K C810 CF93MMA2E-105K
Resistors
Item No. Part Number Rat ing Description
R801 QRX017J-100S 100 Ω 1 W Uninflammable O.M.F.
R802 QRX017J-100S " "
R8O3 QRG027J-681 680 Ω 2 W "
R804 QRD141J-153 1.5 kΩ 1/4 W Carbon
R8O5 QRD141J-272 2.7 kΩ " "
Item No. Part Number Rating Description
E10151-001 Circuit Board
E43727-002 Tab
52868-3 Terminal
LN-22 L.E.D. (for indicator)
E49578-001 L.E.D. Holder
Page 12

Fig. 16

Page 13
Transistors
Item No o. Part Number Rati ng Description Maker
Рс fT
X701 2SD313V (D, E) 20 W 8 MHz Silicon (NPN) Sanyo
X702 2SB507V (D, E) " '' (PNP) ''
X703 2SC1775AV (E, F) 300 mW 200 MHz " (NPN) Hitachi
X704 2SA872AV (D, E) " " (PNP) "
Diodes
Item No. Part Number Rating Description Maker
D701 ESAB02-02C Silicon Fuji Denki
D702 ESAB02-02N ,,,
D703 ESAB02-02N ·/ / //
ZD701 WZ-130 13 V Zener JRC
Capacitors
Item No. Part Number Rating Description
C701 QEW22AA-107 100 μF 100 V Electrolytic
C702 QEW22AA-107 "
C703 QEW51JA-476 47 μF 63 V
C704 QEW51JA-476 "
C705 QCS31HJ-331 330 pF 50 V Ceramic
C706 QCS31HJ-331 "
C707 QEW51HA-106 10 µF " Electrolytic
C708 QEW51EA-106 " 25 V "
C709 QFZ0075-223 0.022 μF 600 V Metalized Mylar
C710 QEW51JA-107 100 μF 63 V Electrolytic
C711 QEW51JA-106 10 μF "
C712 QEW51JA-107 100 μF " "
C713 QEW22AA-107 100 μF 100 V "
C714 QEW22AA-107 " " "
C716 QFH42AK-224 0.22 μF 100 V Metalized Mylar
Resistors
Item No. Part Number Rati ng Description
· 8701 QRD126J-392 3 .9 kΩ 1/2 W Si. Transistor
R702 QRD141J-392 " 1/4 W Carbon
R703 QRD126J-471 470 Ω 1/2 W Si. Transistor
R704 QRD141J-471 " 1/4 W Carbon
R705 QRD126J-100 10 Ω 1/2 W Si. Transistor
R706 QRD126J-100 " '' "
R707 QRD126J-682 6.8 kΩ
R708 QRD141J-473 47 kΩ 1/4 W Carbon
R709 QRD141J-393 3 9 kΩ
R710 QRD141J-153 15 kΩ " "
R7 1 1 QRD141J-182 1.8 kΩ ,, "
R712 QRD141J-473 47 kΩ " "
R715 QRD141J-680 68 Ω "
Item No. Part Number Rating Description
E34759-002 Circuit Board
E43727-002 Tab
E48965-002 Fuse Clip
Page 14

Fig. 17

Diodes
Item No. Part Number Ratin g Description Maker
D501 S5VB20 5 A Bridge Shindengen
Capacitors
Item No. Part Number Rati ng Description
C501 CF93MMA2G-223K 0.022 μF 400 V Metałized Mylar
C502 MDD-2E-225K 2.2 μF 50 V
C503 MDD-2E-225K
Resistors
Item No. Part Number Rati ng Description
R501 QRG129J-473 47 1/2 W Uninflammable O.M.F.
Item No. Part Number Rating Description Q'ty
E34760-001 Circuit Board 2
E40130-001 Tab 16
E43727-002 " 22
Page 15

8-(4) TPS-86 AC Fuse P.C.Board Ass'y

Fig. 18

Capacitors
Item No. Part Number Rating Description
C401 QFH53AM-103 0.01 μF 1000 V Matalized Mylar
C402 QFH53AM-103 ,, ,,
Item No. Part Number Rating Description Q'ty
E34758-002 Circuit Board 1
E40130 Tab 2
E43727-002 Tab 12
E45524-001 Contact clip 10
Page 16

Trans istors & IC
- i ans 100010 ~
ltem No. Part Number Rati ng Description Make
Рс fT
IC602 MPA63H1 250 mW I.C. NEC
X604 2SC1775AV (F) 300 mW 200 MHz Silicon (NPN) Hitaci
X606 2SC1775AV (F) " "
X608 2SC1775AV (F) " " " "
X6 10 2SC1775AV (F) " " "
X6 12 2SC1775AV (F) " " "
X6 14 2SA899 (B, V) 1000 mW 100 MHz " (PNP) Fuji
X6 16 2SC1904 (B, V) " " (NPN) "
X6 18 2SA899 (B, V) " " (PNP) "
X622 2SD381 (L, M) 20 W 60 MHz " (NPN) NEC
X624 2SB536 (L, M) " " (PNP) "
Page 17
Transistors & IC
Item No. Part Number Rat ing Description Maker
Pc fT
X901 2SC1775AV (F) 300 mW 200 MHz (NPN) Hitachi
X902 2SC1775AV (F) " " "
X903 2SC1775AV (F) " " ., ., "
X904 2SC1775AV (F) " " "
X905 2SA872AV (E) " " " (PNP)
X906 2SA872AV (E) " ., ., "
X907 2SD438 (E) 750 mW 100 MHz " (NPN) Sanyo
Diodes
Item No. Part Number Maker
D602 1S2471F Toyo Dengu
D604 1S2471F "
D901 1S2473 "
D902 1S2473 "
Capacitors
Item No. Part Number Ratir ıg Description
C602 QEW51JA-476 47 μF 63 V Electrolytic
C608 QCS12HJ-330 33 pF 100 V Ceramic
C610 QCS12HJ-7R0 7 pF " "
C612 QCS12HJ-3R0 ЗрF " "
C614 QFM31HK-562 0.0056 μF 50 V Mylar
C618 QFM31HK-273 0.027 μF " "
C620 QFM31HK-104 0.1 μF "
C622 QFM31HK-683 0.068 μF " "
C624 QFM31HK-563 0.056 μF " "
C626 QFM31HK-823 0.082 μF " "
C628 QEW51AA-227 220 μF 10 V Electrolytic
C630 QEW51AA-227 " " "
C632 CF93MMA2E-684K 0.68 μF 250 V Metalized Mylar
C634 QCS31HJ-180 18 pF 50 V Ceramic
C636 QCS12HJ-1R0 1 pF 100 V "
C901 QEW51EA-106 10 µF 25 V Electrolytic
C902 QEW51CA-107 100 μF 16 V "
C904 QEW51AA-227 220 μF 10 V "
C905 QEW51AA-227 | " U.
C906 QFM31HK-104 0.1 μF 50 V Mylar
C907 QFM31HK-104 " "
Resistors
Item No. Part Number Rati ing Description
R602 QRZ0019-104 100 kΩ 1/4 W Carbon Low Noise
R604 QRZ0019-222 2.2 kΩ " " "
R606 QRZ0019-154 150 kΩ " " ,,
R608 QRZ0019-393 39 11. " "
R610 QRZ0019-123 12 kΩ 11. " "
R612 QRZ0019-333 33 11. "
R614 QRZ0019-333 " " " "
R616 QRZ0019-182 1.8 kΩ " "
R618 QRZ0019-182 " " "
R620 QRD141J-562 5.6 kΩ " "
R622 QRD126J-121 120 Ω 1/2 W Uninflammat ole Carbon
R624 QRD126J-121 " "
R626 QRZ0019-273 27 kΩ 1/4 W Carbon Low Noise
R628 QRZ0019-273 ,,, "
Page 18
Resistors
Item No. Part Number Ratii ng Description
R630 QRZ0019-273 27 kΩ 1/4 W Carbon Low Noise
R632 QVP9A0B-221 220 Ω (B) 1/8 W Variable Semi Fix
R634 QRZ0019-182 1.8 kΩ 1/4 W Carbon Low Noise
R636 QRZ0019-563 56 kΩ "
R638 QRG017J-682S 6.8 kΩ 1 W Uninflammable e O.M.F.
R640 QRG017J-392S 3.9 kΩ " "
R642 QRZ0019-682 6.8 kΩ 1/4 W Carbon Low Noise
R644 QRZ0019-122 1.2 kΩ " "
R646 QVP9A0B-102 1 kΩ (B) 1/8 W Variable Semi Fix
R648 QRG129J-470 47 Ω 1/2 W Uninflammable e O.M.F.
R650 QRG129J-470 " " "
R652 QRD141J-471 470 Ω 1/4 W Carbon
R654 QRD141J-470 47 Ω "
R656 QRD141J-470 " "
R658 QRX129J-100 10 Ω 1/2 W Uninflammable e M.F.
B660 ORX129J-100 "
B662 ORD141J-820 82 Ω 1/4 W Carbon
R664 QRD141J-3R3 3.3 Ω "
B666 ORD141J-3R3 "
R668 QRM054K-R47S 0.47 Ω 5 W Metal Planer Cement
R670 QRM054K-R47S " " " "
R672 QRM054K-R47S " " "
R674 QRM054K-R47S " " "
R676 QRX129J-4R7 4.7 Ω 1/2 W Uninflammable e M.F.
R678 QRD141J-121 120 Ω 1/4 W Carbon
R680 QRD141J-101 100 Ω " "
R682 QRD141J-101 " "
R901 QRD141J-222 2.2 kΩ " "
R902 QRD141J-222 " " "
R903 QRD141J-562 5.6 kΩ "
R904 QRD141J-562 " "
R905 QRD141J-101 100 Ω " "
R906 QRD141J-101 " " "
R907 QRD141J-471 470 Ω "
R908 QRD141J-471 " " "
R909 QRD141J-123 12 kΩ " "
R910 QRD141J-123 " "
R911 QRD141J-104 100 kΩ " "
R912 QRD126J-471 470 Ω 1/2 W Uninflammable e Carbon
R913 QRD141J-224 220 1/4 W Carbon
R914 QRD141J-822 8.2 kΩ "
R915 QRD141J-472 4.7 kΩ " "
R9 16 QRD141J-124 120 kΩ " "
R917 QRD126J-680 68 Ω | 1/2 W Uninflammable e Carbon
R9 18 QRD141J-183 18 kΩ 1/4 W Carbon
R9 19 QRD141J-153 | 15 kΩ " "
R920 QRD141J-562 | 5.6 kΩ " ,,
R921 QRD141J-822 8.2 kΩ " "
R922 QRG027J-681 680 Ω 2 W Uninflammable e O.M.F.
R923 QRG017J-331S 330 Ω | 1 W "
ltem No. Part Number Rating Description
E22199-001 Circuit Board
E61537-001 Heat Sink
L602 E04059-1R2 1.2 mH Choke Coil
SPSP3005M Screw (to fix the heat sink)
RY901 ESK1D24-214D Relay
E03606-001 Hole Contact Pin (for test point)
Page 19

Fig. 20

Transistors & IC
ltem No. Part Number Ratii ng Description Maker
Рс fT
IC601 MPA63H1 250 mW I.C. NEC
X603 2SC1775AV (F) 300 mW 200 MHz Silicon (NPN) Hitachi
X605 2SC1775AV (F) ,, " 11
X607 2SC1775AV (F) " " 11
X609 2SC1775AV (F) '' "
X611 2SC1775AV (F) " " ,, ,, "
X613 2SA899 (B, V) 1000 mW 100 MHz " (PNP) Fuji
X615 2SC1904 (B, V) " " " (NPN) ii
X617 2SA899 (B, V) " " (PNP) 11
X62 1 2SD381 (L, M) 20 W 60 MHz " (NPN) NEC
X623 2SB536 (L, M) " " (PNP) "
Diodes
Item No. Part Number Rating Description Maker
D601 1S2471F Toyo Dengu
D603 1S2471F ,,
Page 20
Capacitors
Item No. Part Number Ratir ıg Description
C601 QEW51JA-476 47 μF 63 V Electrolytic
C607 QCS12HJ-330 33 pF 100 V Ceramic
C609 QCS12HJ-7R0 7 pF "
C611 QCS12HJ-3R0 3 pF "
C613 QFM31HK-562 0.0056 μF 50 V Mylar
C619 QFM31HK-104 0.1 μF " "
C621 QFM31HK-683 0.068 μF "
C623 QFM31HK-563 0.056 μF
C625 QFM31HK-823 0.082 μF "
C627 QEW51AA-227 220 µF 10 V Electrolytic
C629 QEW51AA-227 " " "
C631 CF93MMA2E-684K 0.68 μF 250 V Metalized Mylar
C633 QCS31HJ-180 18 pF 50 V Ceramic
C635 QCS12HJ-1R0 1 pF 100 V
Resistors
Item No. Part Number Rating Description
R603 QRZ0019-222 2.2 kΩ 1/4 W Carbon Low Noise
R605 QRZ0019-154 150 kΩ "
R607 QRZ0019-393 3 9 kΩ
R609 QRZ0019-123 12 kΩ
R611 QRZ0019-333 33 '''
R613 QRZ0019-333 33 "
R615 QRZ0019-182 1.8 kΩ " ,
R617 QRZ0019-182 " " " "
R619 QRD141J-562 5.6 kΩ "
R621 QRD126J-121 120 Ω 1/2 W Uninflammable Carbon
R623 QRD126J-121 " "
R625 QRZ0019-273 27 kΩ 1/4 W Carbon
R627 QRZ0019-273 '' " "
R629 QRZ0019-273 "
R631 QVP9A0B-221 220 Ω (B) 1/8 W Variable Semi Fix
R633 QRZ0019-182 1.8 kΩ 1/4 W Carbon
R635 QRZ0019-563 56 kΩ " "
R637 QRG017J-682S 6.8 kΩ 1 W Uninflammable O.M.F.
R639 QRG017J-392S 3.9 "
R641 QRZ0019-682 6.8 kΩ 1/4 W Carbon
R643 QRZ0019-122 1.2 kΩ "
R645 QVP9A0B-222 2.2 kΩ (B) 1/8 W Variable
R647 QRG129J-470 47 Ω 1/2 W Uninflammable Carbon
R649 QRG129J-470 " Uninflammable O.M.F.
R651 QRD141J-471 470 Ω 1/4 W Carbon
R653 QRD141J-470 47 Ω ,,, "
R655 QRD141J-470 ,, ,,, , ''
R657 QRX129J-100 10 Ω 1/2 W Uninflammable M.F.
R659 QRX129J-100 ,,, ,,
R661 QRD141J-820 82 Ω 1/4 W Carbon
R663 QRD141J-3R3 3.3 Ω ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,, "
R665 QRD141J-3R3 ,,, ,,,
R667 QRM054K-R47S 0.47 Ω 5 W Metal Planer
R669 QRM054K-R47S | "
R671 QRM054K-R47S "
R673 QRM054K-R47S "
R675 QRX129J-4R7 4.7 Ω 1/2 W Uninflammable M.F.
R677 QRD141J-121 120 Ω 1/4 W Carbon
R679 QRD141J-101 100 \\
R681 QRD141J-101 | "
Page 21
Circuit Board & Others
Item No. Part Number Rating Description
E22218-001 Circuit Board
E61537-001 Heat Sink
L601 E04059-1R2 1.2 mH Choke Coil
SPSP3005M Screw

9. Accessories List

Part Number Description Q'ty
E30580-624A Instruction Book 1
E64207-002 Envelope for Accessories 1
BT20032 JVC Warranty Card 1
BT20023 Service Procedure 1
BT20024B Caution 1

10. Packing Materials and Part Numbers

Fig. 21

Page 22

11. Transistor Lead Identification

Fig. 22

12. Parts List with Specified Numbers for Designated Areas

Page Item No. Description Original For Europe
11 A Class Power Supply P.C. Board Ass'y TPS-78C TPS-78B
14 Fuse P.C. Board Ass'y TPS-86B TPS-86D
5 18 Plug Cover Not included E48633-001
Power Cord QMP1700-244 E03544-001
Warranty Card BT20032 Not included
Voltage Select Plug E03676-001 "
Voltage Select Socket E03676-002 "
Bracket E61887-001 "
Fuse (F1) QMF61U1-3R0 QMF51A2-5R
" (F2) QMF61U1-3R0 QMF51A2-3R15
" (F3) QMF61U1-3R0 QMF51A2-3R15
" (F4) QMF61U1-3R0 QMF51A2-5R0
" (F5) QMF61M1-R20 QMF61M1-R2(
" (F701) Not included QMF61M1-R2
" (F702) QMF61M1-R2(
" (F703) ,, QMF51A2-5R0
" (F704) " QMF51A2-5R

Comparison Table for Line Voltage, Power Consumption by Areas

M-3030 Line Voltage
U.S.A. AC 120 V, 50/60 Hz 243 W
Europe & Other Areas AC 100/120/220/240 V, 50/60 Hz 820 W
Page 23

Page 24

M-3030 No. 2420

Page 25

14. M-3030 Schematic Diagrams for Designated Areas

M-3030 No. 2420

Page 26

c Diagrams for Designated Areas

Fig. 24

- 23 -

Loading...