JVC LD-HD2KE, LD-HD2KU User Manual

®
Machine Models Compatible for Con-
nection with this Product
DLA-HD2KU
This product (LD-HD2KU) is exclusively for the above-mentioned model. The performance cannot be guaranteed when using with other models. This processor is used as a dedicated machine and this manual (instruction manual) may contain de­scription of features as well as specifications not used by the processor.
DLA-HD2KE
This product (LD-HD2KE) is exclusively for the above-mentioned model. The performance cannot be guaranteed when using with other models. This processor is used as a dedicated machine and this manual (instruction manual) may contain de­scription of features as well as specifications not used by the processor.
DIGITAL VIDEO PROCESSOR
LD-HD2KU/LD-HD2KE
OFF
VIDEO
S-VIDEO
RGB YCrCb
PASS-T
PASS-TX
MENU
PROFILE
STORE
1 2 3
4 5 6
7 8 9
0
BRIGHTNESS CONTRAST
COLOR DETAIL
TINT
ANAMORPHIC
4:3 LETTERBOX
®
INSTRUCTIONS
For customer Use:
Model No.
LD-HD2KU
Serial No.
LCT1679-001A

SAFETY PRECAUTIONS

IMPORTANT INFORMATION
WARNING: TO PREVENT FIRE OR SHOCK HAZ­ARDS, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
To reduce the risk of electric shock, do not remove cover. Refer servicing to qualified service personnel.
This product is equipped with a 3-blade grounding type plug to satisfy UL, CUL, TUV, FCC rules. If you are unable to insert the plug into the outlet, contact your electrician.
FCC INFORMATION (U.S.A. ONLY)
CAUTION:
Changes or modifications not approved by JVC could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital devices, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a resi­dential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful inter­ference to radio communications. However, there is no guarantee that interference will not oc­cur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encourage to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment. – Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician
for help.
About the installation place
Do not install the processor in a place that cannot support its weight securely, or that does not allow for proper heat venti­lation.
IMPORTANT SAFEGUARDS
IMPROPER USE OF THIS EQUIPMENT CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZ­ARD.
In order not to defeat the safeguards incorporated into this product, observe the following basic rules for its installation, use and service. – All the safety and operating instructions should be read
before the product is operated.
– The safety and operating instructions should be followed
and retained for future reference.
– All warnings on the product and in the operating instruc-
tions should be adhered to.
– Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
– Do not use attachments not recommended by the product
manufacturer as they may be hazardous.
– Do not use this product near water. Do not use immedi-
ately after moving from a low temperature to high tempera­ture, as this causes condensation, which may result in fire, electric shock, or other hazards.
– Do not place this product on an unstable cart, stand, or
table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. The product should be mounted according to the manufacturer’s instruc­tions, and should use a mount recommended by the manu­facturer.
– When the product is used on a cart, care should be taken
to avoid quick stops, excessive force, and uneven surfaces which may cause the product and cart to overturn, damag­ing equipment or causing possible injury to the operator.
– Slots and openings in the cabinet are provided for ventila-
tion. These ensure reliable operation of the product and protect it from overheating. These openings must not be blocked or covered. (The openings should never be blocked by placing the product on bed, sofa, rug, or similar surface. It should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided and the manufacturer’s instructions have been adhered to.)
–This product should be operated only with the type of power
source indicated on the label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company.
– This product is equipped with a three-wire plug.
This plug will fit only into a grounded power outlet. If you are unable to insert the plug into the outlet, contact your electrician to install the proper outlet. Do not defeat the safety purpose of the grounded plug.
–Power-supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them. Pay particular attention to cords at doors, plugs, receptacles, and the point where they exit from the product.
–For added protection of this product during a lightning storm,
or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will prevent damage to the product due to light­ning and power line surges.
2
– Do not overload wall outlets, extension cords, or conve-
nience receptacles on other equipment as this can result in a risk of fire or electric shock.
–Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.
– Do not attempt to service this product yourself as opening
or removing covers may expose you to dangerous voltages and other hazards. Refer all service to qualified service personnel.
– Unplug this product from the wall outlet and refer service
to qualified service personnel under the following condi­tions: a) When the power supply cord or plug is damaged. b) If liquid has been spilled, or objects have fallen on the
product. c) If the product has been exposed to rain or water. d) If the product does not operate normally by following
the operating instructions. Adjust only those controls that
are covered by the Operation Manual, as an improper
adjustment of controls may result in damage and will
often require extensive work by a qualified technician to
restore the product to normal operation. e) If the product has been dropped or damaged in any
way. f ) When the product exhibits a distinct change in perfor-
mance – this indicates a need for service.
– When replacement parts are required, be sure the service
technician has used replacement parts specified by the manufacturer or with same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
– Upon completion of any service or repairs to this product,
ask the service technician to perform safety checks to de­termine that the product is in proper operating condition.
– The product should be placed more than one foot away
from heat sources such as radiators, heat registers, stoves, and other products (including amplifiers) that produce heat.
– When connecting other products such as VCR’s, and per-
sonal computers, you should turn off the power of this prod­uct for protection against electric shock.
– Use only the accessory cord designed for this product to
prevent shock.
*DO NOT allow any unqualified person to install the unit.
Be sure to ask your dealer to install the unit since special technical knowledge and skills are required for installation and connection to multiple devices.
If installation is performed by an unqualified person, it may cause personal injury or electrical shock.
Precautions for using the screen terminal
Connect the cable to the screen before using the screen ter­minal of this unit. Signal with DC+12 V/100 mA max. is output from the screen terminal of this unit. Short-circuit will result in malfunction, fire and electric shock. Leave the connection of the wires to the installation contrac­tor.
The power supply voltage rating of this product is AC 120 V, AC 100 V - AC 240 V, the power cord attached conforms to the following power supply voltage. Use only the power cord designated by our dealer to ensure Safety and EMC. When it is used by other power supply voltage, power cable must be changed.
Ensure that the power cable used for the projector is the cor­rect type for the AC outlet in your country. Consult your product dealer.
3

TABLE OF CONTENTS

SAFETY PRECAUTIONS ............................................................................................................................................... 2
QUICK START ................................................................................................................................................................ 5
INSTALLATION ............................................................................................................................................................... 6
SETUP ............................................................................................................................................................................ 8
IR REMOTE/OSD ......................................................................................................................................................... 10
RS232 ........................................................................................................................................................................... 13
HELP MENUS ............................................................................................................................................................... 16
SPECIFICATIONS ......................................................................................................................................................... 17
4

QUICK START

Connection with Other Devices
Before connecting to other devices, ensure to turn off the power supply of the device to be connected with the digital video processor.
Connecting to a Projector
Read through the projector’s instruction manual thoroughly.
Depending on the DVI cable used, signals may be attenuated and images may become unstable. Use high-quality DVI
cables that are 5 m or shorter. When a DVI cable longer than 5 m is used, make use of a distribution system or an optical fiber cable.
Right End of this Unit
DVI
VIDEO IN
Caution on Devices to be Connected
Please refer to the list of ‘Devices Compatible with this Product’ on the front page for devices that can be connected with this unit. Performance of this unit will not be guaranteed if it is connected with a device not specified in the list.
Setup of this Unit
1. Connect the supplied power cord to the power supply in­put terminal on this unit. Connect the earth wire to the equipped earth terminal in the building, followed by in­serting the plug of the supplied power cord into the wall outlet.
2. This unit will be initialized once the plug of the power cord is inserted into the power outlet. Upon completion of ini­tialization, this unit switches to the Standby mode (LED turns red).
3. Press the Power/Standby button on this unit (or Power button on the remote). Once the unit is turned on, the LED turns green.
4. Press the Menu button on the remote for 5 seconds or more to display the Setup Menu on this unit’s display panel. After the Setup Menu is displayed, use the Func­tion Up/Down keys on the remote to select an adjustment. Select the set values accordingly using the Value Left/ Right keys on the remote.
5. Select Set: SCANRATE and set the value to 1920 x 1080.
Press the STORE key on the remote. The message “Are You Sure” is displayed on the display panel of this unit. Press the STORE key on the remote again to set the scan rate.
H/C SYNC V SYNC
UTPUT
I/R REMOTE
DVI INPUT
SCREEN
RS-232
DVI OUTPUT
100-240 VAC 50-60Hz 35 WATTS
DVI Connection Cable (sold separately)
6. Select Set: Active Output and set the value to Digital.
7. Select Set: Screen Shape and set the value to Wide Screen.
8. Press the Menu button on the remote to exit the Setup Menu.
Profile Setting
This unit can store up to 8 profiles. Each profile stores values that have been set for this unit during each adjustment. Select the profile number (1 - 8) at the OSD and press the STORE key on the remote to save the current settings. For further details, please refer to ‘OSD’. ( Page 10)
Video Image Adjustment
The following item can be adjusted according to the input signals. Adjusted values can also be stored in the profile.
BRIGHTNESS ( Page 11)
CONTRAST ( Page 11)
COLOR ( Page 12)
TINT ( Page 12)
DETAIL ( Page 12)
ADVANCED COLOR SYSTEM ( Page 12)
5

INSTALLATION

389pq
OUTPUT
INPUT
Y/C
VIDEO
RED/Pr
GREEN/Y BLUE/Pb C-SYNC HDTV INPUT
21
RED/Pr GREEN/Y
MONITOR OUTPUT
45 67 w
INSTALLATION
Accessories
The following accessories are packed together with this unit. Please confirm all items. If any item is missing, please contact your dealer.
• Instructions • Remote Control
• Power Cord • AA/R6 size Battery (for operation confirmation)
• Guarantee
Placement
The processor can be either placed on a table or rack mounted. A rack mounting installation kit is available. Securely mount the side rack brackets with the screws that are provided with the kit.
Ventilation
The unit uses convection to cool. A fan is not needed. As hot air raises out of the top vent, cool air is drawn in from the bottom and side. These vents must not be blocked. When rack mounted, a minimum of 1.75” (1 rack unit height) of free space is required above and below the unit to allow for proper cooling. A forced air fan should be added to the rack installation if power amps are located in the same air space. Do not install unit above power amps.
Connections
Because of the high performance of this unit it is very important to use the highest quality cables possible, for both input and output signals. To avoid AC ground loop problems, the source equipment, this unit and projector should all be running on the same grounded AC power line (one rated for the power requirements).
1 S-Video input (4-pin DIN) for sources such as DVDs,
Satellite systems, S-VHS tape decks (when using S-VHS tapes only), Hi-8 tape decks.
BLUE/Pb H/C SYNC V SYNC
I/R REMOTE
DVI INPUT
SCREEN
RS-232
DVI OUTPUT
100-240 VAC 50-60Hz 35 WATTS
3 YPrPb/RGBs Input (BNC): 480i and HDTV scan rates are
sent to the internal processor and then output at the se­lected scan rate. If the output is set to analog RGBHV or digital DVI, the unit will automatically transcode the YPrPb HDTV to RGBHV.
Note on DVDs:
For proper aspect ratio and to insure the highest quality image from the DVD player, be sure to set the DVD screen shape to 16:9 in the DVD player’s Setup menu. See the DVD player’s owner’s manual for details.
4 High scan rate input (D-sub15 pin) for sources such as
HDTV signals or computers are passed through to the projector. The signal is sent to the outputs in the same format as the input unless Transcoding is selected. YPrPb from HDTV sources can be transcoded to RGBHV, as well. Use a BNC to D15 breakout cable if necessary. The Green, Red, Blue BNCs are used for YPrPb.
5 D-sub15 pin connector output for use with computer moni-
tors or to a second display device. Use only short cable runs. This output can be used at the same time as the BNC outputs.
6 DVI Input. The DVI Input will automatically process 480p,
720p and 1080p signals. Computer rates are not sup­ported for processing but may be passed through to the DVI output if any of the pass-through inputs are selected. This unit will not convert a computer DVI output to the analog output.
Note
For incompatible input signals, a “Not Supported” message will be displayed on the LCD display and the image will be muted (black screen).
6
2 Composite video input (BNC) for sources such as
Laserdisc players, cable TV, VHS tape decks, 8mm tape decks.
Loading...
+ 14 hidden pages