JVC 0405TNH-II-IM, LCT1881-001A-A User Manual

LCD Flat Television Users Guide

For Models:

LT-37X776 LT-32X776 LT-26X776

Illustration of LT-32X776 and RM-C14G

Important Note:

In the spaces below, enter the model and serial number of your television (located at the rear of the television cabinet). Staple your sales receipt or invoice to the inside cover of this guide. Keep this user’s guide in a convenient place for future reference. Keep the carton and original packaging for future use.

Model Number:

Serial Number:

LCT1881-001A-A

0405TNH-II-IM

Important Safety Precautions

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: To reduce the risk of electric shock. Do not

remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel.

The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS TV SET

TO RAIN OR MOISTURE.

CAUTION: TO INSURE PERSONAL SAFETY, OBSERVE THE FOLLOWING RULES

REGARDING THE USE OF THIS UNIT.

1. Operate only from the power source specified on the unit.

2. Avoid damaging the AC plug and power cord.

3. Avoid Improper installation and never position the unit where good ventilation is unattainable.

4. Do not allow objects or liquid into the cabinet openings.

5. In the event of trouble, unplug the unit and call a service technician. Do not attempt to repair it yourself or remove the rear cover.

Changes or modifications not approved by JVC could void the warranty.

* When you don’t use this TV set for a long period of time, be sure to disconnect both the

power plug from the AC outlet and antenna for your safety.

* To prevent electric shock do not use this polarized plug with an extension cord, receptacle or

other outlet unless the blades can be fully inserted to prevent blade exposure.

IMPORTANT RECYCLING INFORMATION

This product has a fluorescent lamp that contains a small amount of mercury. It also

contains lead in some components. Disposal of the materials may be regulated in your

community due to environmental considerations. For disposal or recycling information,

please contact your local authorities, or the Electronic Industries Alliance:

http://www.eiae.org

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

IMPORTANT SAFETY INSTRUCTIONS

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer's

instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug

has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold

with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has

been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15) Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.

16) Avoid improper installation and never position the unit where good ventilation is impossible. When installing this TV, distance recommendations must be maintained between the set and the wall, as well as inside a tightly enclosed area or piece of furniture. Keep to the minimum distance guidelines shown for safe operation.

150 mm

200 mm

150 mm

200 mm

50 mm

17) Cautions for installation

— Do not tilt the TV towards the left or right, or towards the back.

— Install the TV in a corner on the floor so as to keep cords out of the way. — The TV will generate a slight amount of heat during operation. Ensure that sufficient space is

available around the TV to allow satisfactory cooling.

Warnings

Avoiding Ghost Images

Displaying ﬁ xed images for extended periods of time can leave a subtle but temporary ghost image on your screen. To avoid this, mix your viewing pattern.

Examples include, but are not limited to the following:

• Stock-market report bars

• Shopping channel logos and pricing

displays

• Video game patterns or scoreboards

• Bright station logos

• Internet web sites or other computer-style

images.

• DVD discs, video tapes, laser discs

• Broadcast, cable, satellite channels or

digital television tuners/converters.

TV on

Caring for the Cabinet

Normally, light dusting with a soft, non-scratching duster will keep your TV clean.

If you wish to wipe down the television, first unplug it. Then wipe gently with a soft cloth, slightly moistened with water. You can add a few drops of mild liquid detergent to the water to help remove spots of oily dirt.

• DO NOT allow liquid to enter the TV through the ventilation slots.

• DO NOT use strong or abrasive cleaners on the TV.

• DO NOT spray liquids or cleaners directly on the TV’s surface.

• DO NOT rub or scrub the TV harshly. Wipe the set gently with a soft cloth.

For example...

TV off

XYZ XYZ

Caring for the Screen

The screen is treated with an electrostatic-proof coating. When it gets dirty, wipe it gently with a soft cloth. If the screen is very dirty, wipe it down with a cloth dipped in a diluted kitchen cleaner and thoroughly wrung-out. Then wipe immediately after with a clean, dry cloth.

Do not apply alcohol, organic solvents (like acetone), acidic or alkaline cleansers to the screen. These will remove the coating layer and cause discolorations.

Do not push or hit the screen. This could cause scratches on the screen surface and image distortions.

Warnings (Continued...)

How to move the cabinet

Your fingers may become trapped under the TV, causing injuries. Hold the TV at the bottom in the middle, and do not allow the TV to tilt up or down.

The TV may fall causing injuries. Hold the bottom of the stand with your hand and tilt the TV up or down.

Table of Contents

Important Safety Precautions . 2

Warnings . . . . . . . . . . . . 5

Quick Setup . . . . . . . . . . . 9

Unpacking your TV . . . . . . . . . . . . 9

TV Models . . . . . . . . . . . . . . . . 10

TV Remote Control . . . . . . . . . . . 11

Getting Started . . . . . . . . . . . . . 12

Using the Stand . . . . . . . . . . . . 12

The Remote Control . . . . . . . . . . 14

Connecting Your Devices . . . . . . . 15

Interactive Plug In Menu . . . . . . . . 25

Remote Programming . . . . . 28

Setting CATV, VCR and DVD Codes . . . 28

CATV or Satellite Codes . . . . . . . . 28

VCR Codes . . . . . . . . . . . . . . 29

DVD Codes . . . . . . . . . . . . . . 30

Search Codes . . . . . . . . . . . . . 31

Onscreen Menus . . . . . . . . 32

Using the Guide . . . . . . . . . . . . . 32

Onscreen Menu System . . . . . . . . . 33

Initial Setup . . . . . . . . . . 35

Auto Tuner Setup . . . . . . . . . . . . 35

Channel Summary . . . . . . . . . . . . 36

V-Chip . . . . . . . . . . . . . . . . . . 38

Set Lock Code . . . . . . . . . . . . . 44

Auto Demo . . . . . . . . . . . . . . . 45

Illumination . . . . . . . . . . . . . 45

Language . . . . . . . . . . . . . . . . 45

Closed Caption . . . . . . . . . . . . . 46

Auto Shut Off . . . . . . . . . . . . . . 48

XDS ID . . . . . . . . . . . . . . . . . 48

Noise Muting . . . . . . . . . . . . . . 49

Front Panel Lock . . . . . . . . . . . . 49

V1 Smart Input . . . . . . . . . . . 50

Video Input Label . . . . . . . . . . 50

Position Adjustment . . . . . . . . . . . 51

Power Indicator . . . . . . . . . . . . . 51

Video-1 Monitor Out . . . . . . . . . . 51

Digital-In . . . . . . . . . . . . . . . . . 52

Digital-In Audio . . . . . . . . . . . . . 52

Picture Adjust . . . . . . . . . 53

Picture Settings . . . . . . . . . . . . . 53

Adjust Picture Settings . . . . . . . . . 53

Color Temperature . . . . . . . . . . . . 53

Digital Noise Clear . . . . . . . . . . . . 54

Color Management . . . . . . . . . . 54

Dynamic Gamma . . . . . . . . . . 54

Smart Picture . . . . . . . . . . . . . . 55

Reset . . . . . . . . . . . . . . . . . . 55

Sound Adjust . . . . . . . . . 56

Sound Settings . . . . . . . . . . . . . 56

Adjust Sound Settings . . . . . . . . . 56

Reset . . . . . . . . . . . . . . . . 56

Clock Timers . . . . . . . . . . 57

Set Clock . . . . . . . . . . . . . . . . 57

On/Off Timer . . . . . . . . . . . . . . . 58

Button Functions . . . . . . . 59

Multi Screen Function . . . . . . . . . . 59

Index . . . . . . . . . . . . . . . . . . 59

Twin . . . . . . . . . . . . . . . . . 59

Freeze . . . . . . . . . . . . . . . . . . 60

Swap . . . . . . . . . . . . . . . . . 60

Select . . . . . . . . . . . . . . . . . . 60

Power . . . . . . . . . . . . . . . . . . 61

Number Buttons . . . . . . . . . . . . . 61

Tune . . . . . . . . . . . . . . . 61

Input . . . . . . . . . . . . . . . . . . . 61

TheaterPro D6500K . . . . . . . . . . . 61

Return+/TV . . . . . . . . . . . . . . . 62

Sound . . . . . . . . . . . . . . . . . . 62

Muting . . . . . . . . . . . . . . . . . . 63

Video Status . . . . . . . . . . . . . . . 63

Natural Cinema . . . . . . . . . . . . . . . 63

Sleep Timer . . . . . . . . . . . . . . . 64

ML/MTS . . . . . . . . . . . . . . . . . 64

Display . . . . . . . . . . . . . . . . . 65

C.C. . . . . . . . . . . . . . . . . . . . 65

Channel +/- . . . . . . . . . . . . . 65

Volume +/- . . . . . . . . . . . . . 65

Favorite . . . . . . . . . . . . . . . . . 66

Aspect . . . . . . . . . . . . . . . . . 67

Aspect Ratios . . . . . . . . . . . . . 68

Menu . . . . . . . . . . . . . . . . . . 68

OK . . . . . . . . . . . . . . . . . . . 68

Back . . . . . . . . . . . . . . . . . . . 68

TV/CATV Slide Switch . . . . . . . . . . 69

VCR/DVD Slide Switch . . . . . . . . . 69

VCR Buttons . . . . . . . . . . . . . . . 69

DVD Buttons . . . . . . . . . . . . . . . 69

Light . . . . . . . . . . . . . . . . . . . 69

Table of Contents

Digital Setup . . . . . . . . . 70

Digital Setup . . . . . . . . . . . . . 70

Antenna Level . . . . . . . . . . . . . 70

Digital Sound . . . . . . . . . . . . . 71

Aspect Ratio . . . . . . . . . . . . . 71

Cable Card Application . . . . . . . . . 72

i.LINK Auto Play . . . . . . . . . . . 72

Software Update . . . . . . . . . . . 72

Digital Button Functions . . . 73

Digital CH D/A (Digital/Analog) . . . . . 73

Sub Channel . . . . . . . . . . . . . 73

i.LINK Menu . . . . . . . . . . . . . . . 74

Controller . . . . . . . . . . . . . 74

Device . . . . . . . . . . . . . . 75

Timer . . . . . . . . . . . . . . . 76

Reservation . . . . . . . . . . . . . . 76

Timer Edit . . . . . . . . . . . . . . 77

Guide . . . . . . . . . . . . . . . 78

OSD Information . . . . . . 79

Weak Signal . . . . . . . . . . . . . 79

No Program . . . . . . . . . . . . . 79

Cable Card Information . . . . 80

Cable Card Connection . . . . . . . . 80

Appendices . . . . . . . . . . 81

Troubleshooting . . . . . . . . . . . . . 81

Warranty . . . . . . . . . . . . . . 83

Specifications . . . . . . . . . . . . . 85

Notes . . . . . . . . . . . . . . . . . 86

Quick Setup Unpacking your TV

Thank you for your purchase of a JVC LCD Flat Television. Before you begin setting up your new television, please check to make sure you have all of the following items. In addition to this guide, your television box should include:

1 Television

RF Cable × 2

1 Remote Control

POWER

CATV VCR DVD

ASPECT

MULTI SCREEN

INDEX

SELECT

TWIN

SLEEP

FREEZE

SWAP

ML/MTS

DISPLAY

INPUT

123

D/A

456

i.LINK MENU

789

RETURN+

TIMER

TUNE

THEATER

VIDEO

SUB

FAVORITE

CHANNEL

PRO

STATUS

SUB

NATURAL

SOUND

CINEMA

LIGHT

C.C.

MUTING

GUIDE

VOL VOL

BACK

VCR CHANNEL

VCR DVD

PREV NEXT

POWER

TV VCR

REW

FFPLAY

STOP

REC PAUSE

OPEN CLOSE

STILL PAUSE

RM-C14G

2-WAY SPLITTER

Two Way Splitter x 1

Two AA

Batteries

AA Alkaline

Note: Your television and/or remote control may differ from the examples illustrated here.

Quick Setup TV Models

NOTE: Before you connect your television to another device, please refer to the proper

diagrams for your specific TV and remote. These will help assist you in understanding how to connect your television to another device, as well as use the remote to set up your television.

Rear Panel Diagram

75Ω (VHF/UHF)

S-VIDEO

R - AUDIO - L

Ω (

S-

VIDEO

OVER

VIDEO

OVER

-V

C / D

DIGITAL-IN

CABLE CARD

i.LINK IN/OUT

S400(TS)

OPTICAL OUT

Digital Audio

)

VIDEO

INPUT 3 INPUT 2 INPUT 1

R - AUDIO - L

Pr Pb

INPUT 1 COMPONENT

R - AUDIO - L

DIGITAL IN AUDIO

S-VIDEO

VIDEO

OVER

R L R - AUDIO - L

MONITOR / REC OUT

AUDIO OUT

Side Panel Diagram

Illumination Lamp (Page 45)

POWER PROGRAM/TIMER

ATSC

CABLE IN

/ DIGITAL

DIGITAL-IN

CABLE CARD

IN/OUT

i.LINK

S400(TS)

OUT

OPTICAL

Digital Audio

INPUT MENU/OK POWER< CHANNEL > + VOLUME -

POWER PROGRAM/TIMER

OPERATE

Quick Setup TV Remote Control

CATV VCR DVD

MULTI SCREEN

INDEX

TWIN

FREEZE

SWAP

INPUT

123

D/A

456

i.LINK MENU

789

TIMER

TUNE

THEATER

FAVORITE

PRO

SOUND

C.C.

MUTING

OPEN CLOSE

VOL VOL

VCR CHANNEL

PREV NEXT

REW

REC PAUSE

STOP

RM-C14G

ASPECT

SELECT

ML/MTS

VIDEO

STATUS

NATURAL

CINEMA

VCR DVD

POWER

STILL PAUSE

POWER

SLEEP

DISPLAY

RETURN+

SUB

CHANNEL

SUB

LIGHT

GUIDE

BACK

TV VCR

FFPLAY

RM-C14G

Notes:

• For information on remote control buttons, see pages 59 - 69 and 73 - 78.

• i.LINK MENU, TIMER, SUB CHANNEL, FAVORITE and GUIDE buttons are for digital channels. If your TV is connected to an ATSC antenna or Digital Cable, you can use these buttons.

Quick Setup Getting Started

Getting Started

These quick setup pages will provide you, in four easy steps, with the basic information you need to begin using your new television right away.

If you have questions, or for more detailed information on any of these steps, please consult other sections of this manual.

Step 1 - Using the stand

This TV comes with a Table Top Stand already attached.

This stand can be used to adjust the direction of the TV screen 5° up, 10° down and 20° to the left or right.

These illustrations are for LT-26X776 and LT-32X776. The stand for the LT-37X776 is different. You can only adjust the direction of the TV screen 20º to the left or right.

Tilt the TV up or down

While holding the bottom of the stand with one hand, use your other hand to hold the middle of the top of the TV, and slowly tilt the TV up or down.

• As a safety measure, the stand is constructed so that it requires a certain amount of force to tilt the TV.

Rotate the TV left or right

While holding the bottom of the stand with one hand, use your other hand to hold the edge of the panel and slowly adjust the direction of the TV stand.

Quick Setup Getting Started

Cable Holder

A cable holder which keeps your connection cables tidy is attached on the back of the stand. Gently squeeze the left and right of the cable holder, and pull it to remove it from the stand. After putting the cables in the cable holder, attach it to the back of the stand again.

Cable Holder

Illustration of LT-32X776 and LT-26X776

Illustration of LT-37X776

Remove the terminal cover

There are connection terminals behind the covers on the left and right in the back of the TV. Remove these two covers before connecting an antenna or other devices. The covers can be removed by removing the hooks. When replacing the covers, place the side of the covers against the TV and insert the hooks.

Note:

• Leave the terminal covers off if they do not fit properly. Do not force to replace the covers. Doing so may damage the connection cables and covers.

Illustration of LT-32X776 and LT-26X776 Illustration of LT-37X776

Quick Setup Getting Started

Step 2 – The Remote Control

Before you can operate your remote control, you first need to install the batteries (included).

Slide the cover on the back of the remote down towards the bottom of the remote control. Insert two batteries (included) carefully noting the “+” and “–” markings, placing the “–” end in the unit first. Slide the cover back into place.

When you change the batteries, try to complete the task within three minutes. If you take longer than three minutes, the remote control codes for your VCR, DVD, and/or cable box/satellite receiver may have to be reset. See pages 28 - 31.

Key Feature Buttons

The four key feature buttons at the center of the remote can be used for basic operation of the television. The top and bottom buttons will scan forward and back through the available channels. To move rapidly through the channels using JVC’s Hyperscan feature, press and hold CH+ or CH –. The channels will zip by at a rate of five channels per second. The right and left buttons will turn the volume up or down. These buttons are also marked with four arrows and are used with JVC’s onscreen menu system. To use the onscreen menus, press the M

ENU button.

MUTING

VOL VOL

GUIDE

BACK

Basic Operation

Turn the television on and off by pressing the POWER button at the top right corner of the remote. If this is the first time you are turning on the TV, the interactive plug-in menu appears.

• Make sure the TV/CATV switch is set to TV. Move the switch to CATV only if you need to operate a cable box.

• Slide the VCR/DVD selector switch to VCR to control a VCR. Slide to DVD to control a DVD player. Please see pages 28 to 31 for instructions on programming your remote control to operate a cable box, VCR or DVD player.

POWER

CATV

VCR DVD

Quick Setup Connections

Step 3 - Connecting your devices

To make these connections, you will use plugs like the ones illustrated below.

S-Video Cable

Component Cables

Composite Cables

Audio Cables

Used to make video connections with S-Video VCRs, Camcorders and DVD players.

Used to connect audio/video devices like VCRs, DVD players, stereo amplifiers, game consoles, etc.

Notes:

• These connections are examples.

• After you are finished connecting your devices, plug the power cord into the nearest power outlet and turn on the TV.

• If you follow these diagrams and the television does not work properly, contact your local cable operator.

• To connect a DVD player, see VCR Connection. A DVD player is optional

• If you have a satellite television system, refer to the satellite TV manual.

No VCR Connection

75Ω

Cable or Antenna

Output

Coaxial Cable

(Attachment)

(VHF/UHF)

OUT OUT

Two-way Splitter

(Attachment)

ATSC / DIGITAL

TV Rear Panel

DIGITAL-IN

CABLE IN

Quick Setup Connections

VCR Connection

Notes:

• Green, blue and red are the most common colors for DVD cables. Some models may vary colors. Please consult the user’s manual for your DVD player for more information.

• Be careful not to confuse the red DVD cable with the red audio cable. It is best to complete one set of connections (DVD or audio output) before starting the other to avoid accidentally switching the cables.

• You may also connect the DVD player to Input 1.

Diagram #1

VCR

S-VIDEO

R -

AUDIO - L

S-VIDEO

R -

AUDIO - L

INPUT 3 INPUT 2 INPUT 1

R - AUDIO - L

INPUT 1 COMPONENT

R - AUDIO - L

DIGITAL IN AUDIO

Cable or Antenna

OUT

V L R

VIDEO

OUT

Two-Way Splitter

(Attachment)

Coaxial Cable

(Attachment)

TV Rear Panel

Output

OUT OUT

Ω

75 (VHF/UHF)

ATS / DIGITAL CABLE IN

DIGITAL-IN

CABLE CARD

Green

Blue

Red

AUDIO OUT

OUT

AUDIO OUT

R L

DVD Player (OPTIONAL)

i.LINK IN/OUT

S400(TS)

Note:

• If this connection setup does not work for you, try the connection setup on page 17.

Quick Setup Connections

Diagram #2

VCR

S-VIDEO

R - AUDIO - L

S-VIDEO

R - AUDIO - L

INPUT 3 INPUT 2 INPUT 1

R - AUDIO - L

Pr Pb

INPUT 1 COMPONENT

R - AUDIO - L

DIGITAL IN AUDIO

VIDEO

V L R

OUT

Coaxial Cable

(Attachment)

Cable or Antenna

Output

Two-Way Splitter

OUT OUT

Two-Way Splitter

OUT OUT

(Attachment)

ATS / DIGITAL CABLE IN

TV Rear Panel

75Ω (VHF/UHF)

DIGITAL-IN

Green

Blue

Red

R L

AUDIO OUT

CABLE CARD

OUT

AUDIO OUT

R L

DVD Player (OPTIONAL)

Quick Setup Connections

Connecting to a Camcorder

You can connect a camcorder to you televison by using the input jacks located on the back of the television.

TV Rear Panel

S-VIDEO

INPUT 3 INPUT 2 INPUT 1

S-VIDEO

R - AUDIO - L

R -

AUDIO -

VIDEO

CAMCORDER

1) Connect a yellow composite cable from the camcorder VIDEO OUT, into the VIDEO IN on

the back of the TV, OR connect an S-Video cable from the camcorder to the back of the TV.

2) Connect a white cable from the camcorder LEFT AUDIO OUT, into the LEFT AUDIO IN on

the back of the TV.

3) Connect a red cable from the camcorder RIGHT AUDIO OUT, into the RIGHT AUDIO IN on

the back of the TV.

Note:

• If your camcorder is a mono sound model it will have only one AUDIO OUT. Connect it to the LEFT AUDIO IN on the back of the TV.

Headphone Connection

You can connect a pair of headphones to the television using the headphone jack located on the side of the television.

1) Plug a headphone jack into the headphone jack on the television’s side panel.

POWER+ VOLUME -

TV Side Panel

Quick Setup Connections

Connecting to an External Amplifier

TV Rear Panel

S-VIDEO

OVER

R L

R -

AUDIO -

MONITOR / REC OUT

AUDIO OUT

VIDEO

Speaker

Amplifier

Speake

1) Connect a white cable from the LEFT AUDIO OUTPUT on the back of the TV to the LEFT AUDIO INPUT on the amplifier.

2) Connect a red cable from the RIGHT AUDIO OUTPUT on the back of the TV to the RIGHT AUDIO INPUT on the amplifier.

Notes:

• Refer to your amplifier’s manual for more information.

• You can use AUDIO OUTPUT for your home theater system.

• DVI analog sound can not be outputted.

Connecting to Monitor/Recording Output Terminal

S-VIDEO

VIDEO

OVER

R L R - AUDIO - L

MONITOR / REC OUT

AUDIO OUT

TV Rear Panel

VCR

OUT

R L V

Notes:

• When you make this connection, set the Video-1 Monitor Out menu to ON. See page 51.

• If you are receiving ATSC/Digital Cable signal, it can be outputted to the S-Video output terminal or Video (composite video) terminal.

• If you are receiving Analog TV signal, it can not be outputted to the S-Video output terminal.

• No signal will be outputted through the S-Video output terminal when you are not viewing images coming from the composite video input terminal.

• No signal will be outputted through the Monitor/Recording output terminal when you are viewing images from the component video input.

Quick Setup Connections

Connecting to an AV Receiver using your television's V1 Smart Input

By connecting your AV Receiver to your television's V1 Smart Input, you can watch picture sources from many different devices, without having to change or use the other input connections on your TV. This allows you to free up the other input connections so you can connect more devices to your television.

TV Rear Panel

S-VIDEO

VIDEO

OVER

R - AUDIO -

S-VIDEO

VIDEO

OVER

- AUDIO

INPUT 3 INPUT 2 INPUT 1

R -

Pr Pb

INPUT 1 COMPONENT

R -

DIGITAL IN AUDIO

S-VIDEO

R R -

MONITOR / REC OUT

AUDIO OUT

VIDEO

AUDIO -

VIDEO

OVER

AUDIO -

MONITOR

OUT

AV Receive

MONITOR OUT

1) Connect an S-Video Cable from the AV Receiver's MONITOR OUT, to the S-Video INPUT-1 on the back of your television.

2) Connect a Yellow Composite Cable from the AV Receiver's MONITOR OUT, into the VIDEO INPUT-1 on the back of your television.

3) Connect a Green Component Cable from the AV Receiver's Y MONITOR OUT, into the Y VIDEO INPUT-1 on the back of your television.

4) Connect a Blue Component Cable from the AV Receiver's PB MONITOR OUT, into the Pb VIDEO INPUT-1 on the back of your television.

5) Connect a Red Component Cable from the AV Receiver's P

R MONITOR OUT, into the Pr

VIDEO INPUT-1 on the back of your television.

Notes:

• Please refer to your AV Receiver instruction manual for more information on connecting your

speakers and other devices like a DVD player.

• Use your AV Receiver's remote to switch to the different devices you have connected.

• Some AV Receivers may not respond when the V1 Smart Input function is turned on.

• If you have video connections for each input device connected to your AV Receiver, you

should not connect them using both S-Video and Composite connection at the same time when you are using V1 Input as the V1 Smart Input. In this case we recommend using the S-Video connection.

Quick Setup Connections

Connecting to a Digital TV Receiver

By connecting a Digital TV Receiver, high definition pictures can be displayed on your TV in their digital form.

R -

UDIO -

TV Rear Panel

INPUT 3 INPUT 2

R -

AUD

Pr Pb

INPUT 1 COMPONENT

R - AUDIO -

DIGITAL IN AUDIO

R L

AUDIO OUT

VIDEO

IO -

ATSC / DIGITAL CABLE IN

DIGITAL-IN

CABLE CARD

DTV Decoder

AUDIO OUTDIGITAL OUT

HDMI to DVI Cable

After the connections have been made,

TV Rear Panel

tighten the screw to secure the cables.

1) Connect the HDMI to DVI Cable from the DIGITAL OUT on the back of your DTV decoder, to the DIGITAL-IN on the back of your television.

2) Connect a red cable from the DTV decoder RIGHT AUDIO OUT, to the RIGHT AUDIO DIGITAL-IN on the back of your television.

3) Connect a white cable from the DTV decoder LEFT AUDIO OUT, to the LEFT AUDIO DIGITAL-IN on the back of your television.

• The digital-in terminal is not compatible with the picture signal of a personal computer.

• Use a HDMI to DVI cable (commercially available) in order to digitally connect the television

with a DTV decoder.

Notes:

• If 480p signals (640x480 or 720x480) are displayed on the screen, the horizontal balance

may be slightly shifted. Access the “DIGITAL-IN” in the initial setup menu to adjust it. (Refer to page 52.)

• When you do the above connection, set DIGITAL-IN AUDIO in the Initial Setup menu to

ANALOG. See "DIGITAL-IN AUDIO", page 52.

Quick Setup Connections

Connecting to a HDMI Compatible Device

By connecting a HDMI compatible device, high definition pictures can be displayed on your TV in their digital form. Some HDMI devices can include DVD players, D-VHS or any HDMI compatible device.

HDMI (High Definition Multimedia Interface) is the first industry supported, uncompressed, all digital audio/video interface. HDMI provides and interface between any audio/video source, such as a set-top box, DVD player, A/V receiver or an audio and/or video monitor, such as a digital television (DTV).

HDMI Compatible Device

AUDIO OUT

ATSC / DIGITAL CABLE IN

CABLE CARD

TV Rear Panel

DIGITAL OUT

DIGITAL-IN

HDMI Cable

1) Connect the HDMI Cable from the DIGITAL OUT on the back of your DTV or HDMI device, to the DIGITAL-IN on the back of your television.

Notes:

• When you do the above connection, set DIGITAL-IN AUDIO in the Initial Setup menu to DIGITAL. See "DIGITAL-IN AUDIO", page 52.

• Some decoders may not respond depending on the equipment that you have connected when it is connected to the HDMI.

• If the HDMI output device signal is changed (for example, 480i/60Hz is changed to 480p/60Hz), the screen may turn green and there may be some distortion for a short time until the signal becomes stable.

Quick Setup Connections

Connecting to an amplifier using your optical output

You can connect an amplifier that has an optical digital input terminal by using an optical digital cable from the optical output. The signal that is output can be PCM or Dolby Digital.

Television Rear Panel

i.LINK

S400(TS)

OPTICA

IN/OUT

Digital Audio

OUT

Amplifier

1) Connect the optical cable from underneath the television to the back of the amplifier.

Notes:

• This terminal can only output digital audio.

• In order to use the optical output connection, select PCM or Dolby Digital on Digital Sound in the Digital Setup Menu. See page 71.

• Refer to your owners manual on using your amplifier.

Quick Setup Connections

Connecting an i.LINK compatible device to the back of your television

i.LINK is a digital serial interface that allows devices equipped with an i.LINK connector to exchange digital video signals, digital audio signals and device control signals bi-directionally over a single cable. (For example, a JVC D-VHS VCR).

i.LINK refers to the IEEE1394-1995 industry specification and extensions thereof. The logo is used for products compliant with the i.LINK standard.

This projection television uses a four-pin i.LINK connector to input and output MPEG2 video signals, audio signals and control signals.

TV Rear Panel

IN/OUT

i.LINK

S400(TS)

OPTICAL OUT

Digital Audio

i.LINK Compatible Device

1) Connect the i.LINK cable from underneath the TV to the back of the i.LINK compatible

device.

Notes:

• Use only the S400 i.LINK cable when connection your devices.

• See page 74 on how to select the i.LINK device.

• Refer to your owners manual on using your i.LINK device.

• When recording or playing back video with an i.LINK device, if you perform the Auto Tuner Setup, the video signal you are recording or playing back may stop or you may not be able to perform the Digital Auto Tuner Setup.

• Your television can connect with i.LINK D-VHS decks and HD-Camcorders (JVC brand only). If you connect other brand devices, with i.LINK cable, they will not work.

• It can play only the recorded contents in Digital Mode.

• Use only tapes bearing the DVHS (SVHS) mark for recording.

Quick Setup Plug-In Menu

Step 4 – The Interactive Plug In Menu

When you turn your television on for the first time the interactive plug-in menu will appear. The plug-in menu helps you to get your TV ready to use by letting you set your preferences for:

• The language in which you want the onscreen menus to appear.

• Setting the TV’s clock to the correct time so your timer functions will work properly. You can choose “AUTO” or “MANUAL” for setting the clock.

• The auto tuner setup of which channels you wish to receive.

We recommend you complete the interactive plug-in items before you start using your television.

Notes:

• The interactive plug-in menu setting does not appear if your TV has been turned on before. In this case use the onscreen menus to perform these settings. See pages 45, 57, 35.

• If you press the Menu button while setting up the interactive plug-in menu, it will skip over it.

Language

After the “JVC INTERACTIVE PLUG IN MENU” has been displayed, the TV automatically switches to the LANGUAGE settings. You can choose to view your onscreen menus in three languages: English, French (Français) or Spanish (Español).

LANGUAGE/LANGUE/IDIOMA

ENGLISH

SELECT OPERATE EXIT

√®

To choose a language:

(English, Français or Español)

†

To NEXT (To set clock)

(To be continued...)

Quick Setup Plug-In Menu

Auto Clock Set

Before you use any of your TV’s timer functions, you must first set the clock. You may precisely set your clock using the XDS time signal broadcast by most public analog broadcasting stations. If you do not have this in your area, you will have to set the clock manually. See manual clock set below. To set the clock using the XDS signal:

√®

SET CLOCK

MODE

TIME

TIME ZONE

DATE/YEAR

D.S.T.

SELECT OPERATE EXIT

AUTO

: --

ATLANTIC

JAN/01/05

Notes:

• D.S.T. can be used when it is set to ON in the SET CLOCK menu.

• Only when the MODE is set to AUTO, the Daylight Savings Time feature automatically adjusts your TV’s clock for Daylight Savings. The clock will move forward one hour at 2:00 am on the first Sunday in April. The clock will move back one hour at 2:00 am on the last Sunday in October.

• You will have to reset the clock after a power interruption. You must set the clock before operating any timer functions.

Manual Clock Set

To choose AUTO

†

To TIME ZONE

√®

To select your time zone: (Atlantic, Eastern, Central, Mountain, Pacific, Alaska or Hawaii)

†

To move to D.S.T. (Daylight Savings Time)

√®

To turn D.S.T. ON or OFF

†

To NEXT (To Auto Tuner Setup)

To set your clock manually (without using the XDS signal), choose MANUAL. If you choose AUTO, see auto clock set above.

√®

SET CLOCK

MODE TIME

TIME ZONE

DATE/YEAR

D.S.T.

START CLOCK

SELECT OPERATE EXIT

MANUAL

: --

ATLANTIC

JAN/01/05

To choose MANUAL

†

√®

†

To minute

√®

†

To TIME ZONE

√®

Central, Mountain, Pacific, Alaska or Hawaii)

†

To DATE/YEAR

√®

†

To day

√®

†

To year

√®

†

To move to D.S.T. (Daylight Savings Time)

√®

†

To START CLOCK

To TIME

To set the hour

To set the minute

To select your time zone: (Atlantic, Eastern,

To set the month

To set the day

To set the year

To turn D.S.T. ON or OFF

Note:

• You will have to reset the clock after a power interruption. You must set the clock before operating any timer functions.

(To be continued...)

Quick Setup Plug-In Menu

Auto Tuner Setup

In auto tuner setup, the TV automatically scans through all available channels, memorizing the active ones and skipping over blank ones or channels with weak signals. This means when you scan (using the C two tuner modes to choose from, ANALOG or DIGITAL.

HANNEL +/– buttons) you will receive only clear, active channels. There are

AUTO TUNER SETUP

IN ANALOG

IN DIGITAL TUNER MODE

START

SELECT OPERATE EXIT

ATSC

√®

you skip Analog Auto Tuner Setup)

AIRTUNER MODE

π†

√®

when you skip Digital Auto Tuner Setup)

†

After Analog Auto Tuner Setup is finished, Digital Auto Tuner Setup starts.

To choose CABLE or AIR (or SKIP when

To TUNER MODE (IN DIGITAL)

To choose ATSC or Digital Cable (or SKIP

To START

NOW

Now Programming...

PROGRAMMING !

When the setup is finished, "THANK YOU ! SETUP IS NOW COMPLETE" is displayed. Your quick setup is now complete. You can now begin watching your television, or you can continue on in this guide for more information on programming your remote control, or using the JVC onscreen menu system to customize your television viewing experience.

Notes:

• If you want to cancel the Auto Tuner Setup, press the MENU button.

• Noise muting will not work during Auto Tuner Setup.

• If you choose SKIP, it finished without doing the Auto Tuner Setup.

Cable Box and Satellite Users: After your auto tuner setup is complete, you may, (depending on the type of hookup), have only 1 channel, usually 3 or 4 in the auto tuner memory. This is normal.

STOP

The Quick Setup is complete

+ 61 hidden pages