JVC 0604TNH-II-IM, LCT1636-001A-A User Manual

Color Television Users Guide

For Models:

AV-30W585 AV-30W575

Illustration of AV-30W585 and RM-C1257G

Important Note:

In the spaces below, enter the model and serial number of your television (located at the rear of the television cabinet). Staple your sales receipt or invoice to the inside cover of this guide. Keep this user’s guide in a convenient place for future reference. Keep the carton and original packaging for future use.

Model Number:

Serial Number:

LCT1636-001A-A

0604TNH-II-IM

Important Safety Precautions

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: To reduce the risk of electric shock. Do not

remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel.

The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS TV

SET TO RAIN OR MOISTURE.

CAUTION: TO INSURE PERSONAL SAFETY, OBSERVE THE FOLLOWING RULES

REGARDING THE USE OF THIS UNIT.

1. Operate only from the power source specified on the unit.

2. Avoid damaging the AC plug and power cord.

3. Avoid Improper installation and never position the unit where good ventilation is unattainable.

4. Do not allow objects or liquid into the cabinet openings.

5. In the event of trouble, unplug the unit and call a service technician. Do not attempt to repair it yourself or remove the rear cover.

Changes or modifications not approved by JVC could void the warranty.

* When you don’t use this TV set for a long period of time, be sure to disconnect both the

power plug from the AC outlet and antenna for your safety.

* To prevent electric shock do not use this polarized plug with an extension cord, receptacle or

other outlet unless the blades can be fully inserted to prevent blade exposure.

IMPORTANT RECYCLING INFORMATION

This product utilizes both a Cathode Ray Tube (CRT) and other components that contain lead. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information, please contact your local authorities, or the Electronic Industries Alliance: http://www.eiae.org

• As an “ENERGY STAR®” partner, JVC has determined that this product or product model meets the “ENERGY STAR efficiency.

” guidelines for energy

Important Safeguards

CAUTION:

Please read and retain for your safety.

Electrical energy can perform many useful functions. This TV set has been engineered and manufactured to assure your personal safety. But improper use can result in potential electrical shock or fire hazards. In order not to defeat the safeguards incorporated in this TV set, observe the following basic rules for its installation, use and servicing. Also follow all

warnings and instructions marked on your TV set.

INSTALLATION

1 Your TV set is equipped with a polarized AC line plug (one

blade of the plug is wider than the other). This safety feature allows the plug to fit into the power outlet only one way. Should you be unable to insert the plug fully into the outlet, try reversing the plug. Should it still fail to fit, contact your electrician.

2 Operate the TV set only from a power source as indicated on the TV set or refer to the

operating instructions for this information. If you are not sure of the type of power supply to your home, consult your TV set dealer or local power company. For battery operation, refer to the operating instructions.

3 Overloaded AC outlets and extension cords are dangerous, and so are frayed power cords

and broken plugs. They may result in a shock or fire hazard. Call your service technician for replacement.

4 Do not allow anything to rest on or roll over the power cord, and do not place the TV set

where power cord is subject to traffic or abuse. This may result in a shock or fire hazard.

5 Do not use this TV set near water — for example, near a bathtub, washbowl, kitchen sink, or

laundry tub, in a wet basement, or near swimming pool, etc.

6 If an outside antenna is connected to the TV set, be sure the antenna system is grounded

so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection requirements for the grounding electrode.

(POLARIZED-TYPE)

7 An outside antenna system should not be located in the vicinity of overhead power lines

or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

EXAMPLE OF ANTENNA GROUNDING

AS PER NATIONAL ELECTRICAL CODE

ANTENNA LEAD IN WIRE

GROUND CLAMP

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

ELECTRICAL SERVICE EQUIPMENT

NEC - NATIONAL ELECTRIC CODE

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ARTICLE 250, PART H)

8 TV sets are provided with ventilation openings in the cabinet to allow heat generated during

operation to be released.

Therefore:

— Never block the bottom ventilation slots of a portable TV set by placing it on a bed, sofa,

rug, etc.

— Never place a TV set in a “built-in” enclosure unless proper ventilation is provided. — Never cover the openings with a cloth or other material. — Never place the TV set near or over a radiator or heat register.

9 To avoid personal injury:

— Do not place a TV set on a sloping shelf unless properly secured.

— Use only a cart or stand recommended by the TV set manufacturer. — Do not try to roll a cart with small casters across thresholds or deep pile carpets. — Wall or shelf mounting should follow the manufacturer’s instructions, and should use a

mounting kit approved by the manufacturer.

Use

10 Caution children about dropping or pushing objects into the TV set through cabinet

openings. Some internal parts carry hazardous voltages and contact can result in a fire or electrical shock.

11 Unplug the TV set from the wall outlet before cleaning. Do not use liquid or an aerosol

cleaner.

12 Never add accessories to a TV set that has not been designed for this purpose. Such

additions may result in a hazard.

PORTABLE CART WARNING

(Symbol provided by RETAC)

13 For added protection of the TV set during a lightning storm or when the TV set is to be left

unattended for an extended period of time, unplug it from the wall outlet and disconnect the antenna. This will prevent damage to product due to lightning storms or power line surges.

14 A TV set and cart combination should be moved with care. Quick stops, excessive force,

and uneven surfaces may cause the TV set and cart combination to overturn.

Service

15 Unplug this TV set from the wall outlet and refer servicing to qualified service personnel

under the following conditions: A. When the power cord or plug is damaged or frayed. B. If liquid has been spilled into the TV set. C. If the TV set has been exposed to rain or water. D. If the TV set does not operate normally by following the operating instructions. Adjust

only those controls that are covered in the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the TV set to normal operation.

E. If the TV set has been dropped or damaged in any way. F. When the TV set exhibits a distinct change in performance — this indicates a need for

service.

16 Do not attempt to service this TV set yourself as opening or removing covers may

expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

17 When replacement parts are required, have the service technician verify in writing that the

replacement parts he uses have the same safety characteristics as the original parts. Use of manufacturer’s specified replacement parts can prevent fire, shock, or other hazards.

18 Upon completion of any service or repairs to this TV set, please ask the service technician

to perform the safety check described in the manufacturer’s service literature.

19 When a TV set reaches the end of its useful life, improper disposal could result in a picture

tube implosion. Ask a qualified service technician to dispose of the TV set.

20 Note to CATV system installer.

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

Table of Contents

Quick Setup . . . . . . . . . . . 7

Unpacking your TV . . . . . . . . . . . . 7

TV Model . . . . . . . . . . . . . . . . 8

TV Remote Control . . . . . . . . . . . 11

Getting Started . . . . . . . . . . . . . 12

The Remote Control . . . . . . . . . . 12

Connecting Your Devices . . . . . . . 13

Interactive Plug In Menu . . . . . . . . 22

Remote Programming . . . . . 25

Setting CATV, VCR and DVD Codes . . . 25

CATV or Satellite Codes . . . . . . . . 25

VCR Codes . . . . . . . . . . . . . . 26

DVD Codes . . . . . . . . . . . . . . 27

Search Codes . . . . . . . . . . . . . 28

Onscreen Menus . . . . . . . . 29

Using the Guide . . . . . . . . . . . . . 29

Onscreen Menu System . . . . . . . . . 30

Initial Setup . . . . . . . . . . 32

Auto Tuner Setup . . . . . . . . . . . . 32

Channel Summary . . . . . . . . . . . . 32

V-Chip . . . . . . . . . . . . . . . . . . 34

Set Lock Code . . . . . . . . . . . . . 40

Auto Demo . . . . . . . . . . . . . . . 40

Language . . . . . . . . . . . . . . . . 41

Closed Caption . . . . . . . . . . . . . 41

Auto Shut Off . . . . . . . . . . . . . . 42

XDS ID . . . . . . . . . . . . . . . . . 42

Tilt Correction . . . . . . . . . . . . . . 42

Noise Muting . . . . . . . . . . . . . . 43

Front Panel Lock . . . . . . . . . . . . 43

V1 Smart Input . . . . . . . . . . . . 44

Video Input Label . . . . . . . . . . . . . 44

Position Adjustment . . . . . . . . . . . . 45

Digital-In . . . . . . . . . . . . . . . . . 46

Digital-In Audio . . . . . . . . . . . . . 46

Center CH Input . . . . . . . . . . . . . 47

Audio Out . . . . . . . . . . . . . . . . 47

TV Speaker . . . . . . . . . . . . . . . 48

Picture Adjust . . . . . . . . . 49

Picture Settings . . . . . . . . . . . . . 49

Adjust Picture Settings . . . . . . . . . 49

Color Temperature . . . . . . . . . . . . 49

Digital Noise Clear . . . . . . . . . . . . 50

VSM . . . . . . . . . . . . . . . . . . . 50

Natural Cinema . . . . . . . . . . . . . 50

Reset . . . . . . . . . . . . . . . . . . 51

Sound Adjust . . . . . . . . . 52

Sound Settings . . . . . . . . . . . . . 52

Adjust Sound Settings . . . . . . . . . 52

MTS (Multi-channel Sound) . . . . . . . 52

Reset . . . . . . . . . . . . . . . . . . 52

Clock Timers . . . . . . . . . . 53

Set Clock . . . . . . . . . . . . . . . . 53

On/Off Timer . . . . . . . . . . . . . . . 54

Button Functions . . . . . . . 55

Multi Screen Function . . . . . . . . . . 55

Index . . . . . . . . . . . . . . . . . 55

Twin . . . . . . . . . . . . . . . . . 55

Freeze . . . . . . . . . . . . . . . . 56

Swap . . . . . . . . . . . . . . . . . 56

Select . . . . . . . . . . . . . . . . 56

Power . . . . . . . . . . . . . . . . . . 57

Number Buttons . . . . . . . . . . . . . 57

Tune . . . . . . . . . . . . . . . . . . 57

Input . . . . . . . . . . . . . . . . . . . 57

Channel +/- . . . . . . . . . . . . . . 57

Volume +/- . . . . . . . . . . . . . . . 57

Return . . . . . . . . . . . . . . . 58

Sound . . . . . . . . . . . . . . . . . . 58

Muting . . . . . . . . . . . . . . . . . . 58

Video Status . . . . . . . . . . . . . . . 59

TheaterPro D6500K . . . . . . . . . . . 59

Sleep Timer . . . . . . . . . . . . . . . 59

Display . . . . . . . . . . . . . . . . . 60

C.C. . . . . . . . . . . . . . . . . . . . 60

Aspect . . . . . . . . . . . . . . . . . 61

Aspect Ratios . . . . . . . . . . . . . 61

Menu . . . . . . . . . . . . . . . . . . 62

OK . . . . . . . . . . . . . . . . . . . 62

Back . . . . . . . . . . . . . . . . . . . 62

TV/CATV Slide Switch . . . . . . . . . . 63

VCR/DVD Slide Switch . . . . . . . . . 63

VCR Buttons . . . . . . . . . . . . . . . 63

DVD Buttons . . . . . . . . . . . . . . . 63

Light . . . . . . . . . . . . . . . 63

Appendices . . . . . . . . . . 64

Troubleshooting . . . . . . . . . . . . . 64

Warranty . . . . . . . . . . . . . . . . . 65

Authorized Service Centers . . . . . . . 66

Specifications . . . . . . . . . . . . . 67

Notes . . . . . . . . . . . . . . 68

Quick Setup Unpacking your TV

Thank you for your purchase of a JVC Color Television. Before you begin setting up your new television, please check to make sure you have all of the following items. In addition to this guide, your television box should include:

Two AA

1 Television

1 Remote Control

POWER

CATVVCR

DVD

MULTI SCREEN

TWIN

INDEX

C.C.

SWAP

SELECT

INPUT

FREEZE

DISPLAY

SLEEP TIMER

SOUND

RETURN+

TUNE

VIDEO STATUS

THEATER PRO

LIGHT

ASPECT

MUTING

CH +

VOL

–

CH –

BACK

VCR/DVD

VCR CHANNEL

TV/VCR

POWER

PREV NEXT

PLAY FFREW

REC

STOP PAUSE

OPEN/CLOSE

STILL/PAUSE

RM-C1257G

Once you have unpacked your television, the next step is to connect it to your antenna/ cable or satellite system and to connect the audio/video devices you want to use with your television. To make these connections you will use plugs like the ones illustrated below.

Batteries

AA Alkaline

Note: Your television and/or remote control may differ from the examples illustrated here.

Coaxial Cables

Component Cables

Composite Cables

Audio Cables

Used to connect an external antenna or cable TV system to your TV.

Used to connect audio/ video devices like VCRs, DVD players,

S-Video Cable

stereo amplifiers, game consoles, etc.

AV CompuLink Cable

Used to make video connections with S-Video VCRs, Camcorders and DVD players.

Used to connect JVC AV CompuLink capable components for an automated home theater.

Note: AV-30W585 ONLY

We recommend that before you start using your new television, you read your entire User’s Guide so you can learn about your new television’s many great features. If you’re anxious to start using your television right away, a quick setup guide follows on the next few pages.

Quick Setup TV Models

NOTE: Before you connect your television to another device, please refer to the proper

diagrams for your specific TV and remote. These will help assist you in understanding how to connect your television to another device, as well as use the remote to set up your television.

Rear Panel Diagram

MODEL : AV-30W585

75Ω

( VHF/UHF )

CENTER

CHANNEL IN

UNPLUG THE POWER CORD FROM AC OUTLET BEFORE REMOVING THE REAR COVER

When the rear cover is removed, follow "CAUTION AT DISASSEMBLY" procedure in the service manual before plugging the TV's power cord into an AC outlet. Failure to follow the procedure will result in PERMANENT damage to some of the television features.

DÉBRANCHEZ LE CORDON DE LA PRISE DE COURANT C. A. AVANT DE RETIRER LE COUVERCLE ARRIÈRE.

Une fois le couvercle arrière déposé suivez l procédure « ATTENTION LORS DU DÉMONTAGE » décrite dans une prise c.a. L'omission de suivre la procédure causera des dommages PERMANENTS à certaines fonctions du téléviseur.

DIGITAL - IN

AUDIO

(ANALOG)

VIDEO

(DIGITAL)

AUDIO

(DIGITAL)

SUBWOOFER OUT

COMPULINK

AUDIO OUT

R L

INPUT 3

INPUT 2

INPUT 1

AUDIO

R L

VIDEO S VIDEO

OVER

COMPONENT VIDEO

INPUT 1INPUT 2

Quick Setup TV Models

NOTE: Before you connect your television to another device, please refer to the proper

diagrams for your specific TV and remote. These will help assist you in understanding how to connect your television to another device, as well as use the remote to set up your television.

Rear Panel Diagram

MODEL: AV-30W575

75Ω

( VHF/UHF )

CENTER

CHANNEL IN

UNPLUG THE POWER CORD FROM AC OUTLET BEFORE REMOVING THE REAR COVER

DÉBRANCHEZ LE CORDON DE LA PRISE DE COURANT C. A. AVANT DE RETIRER LE COUVERCLE ARRIÈRE.

DIGITAL - IN

AUDIO

(ANALOG)

VIDEO

(DIGITAL)

AUDIO

(DIGITAL)

SUBWOOFER OUT

AUDIO OUT

R L

INPUT 3

INPUT 2

INPUT 1

AUDIO

R L

VIDEO S VIDEO

OVER

COMPONENT VIDEO

INPUT 1INPUT 2

Quick Setup TV Models

NOTE: Before you connect your television to another device, please refer to the proper

diagrams for your specific TV and remote. These will help assist you in understanding how to connect your television to another device, as well as use the remote to set up your television.

Side panel Diagram

MODELS: AV-30W585 and AV-30W575

INPUT 4

S-VIDEO

OVER

VIDEO

L/MONO

AUDIO

OPERATE

CHANNEL

–

VOLUME

–

Quick Setup TV Remote Control

CATV VCR

FREEZE

DISPLAY

SLEEP TIMER

SOUND

VIDEO STATUS

THEATER PRO

MUTING

VOL

–

VCR CHANNEL

PREV NEXT

REC

OPEN/CLOSE

MULTI SCREEN

TWIN

SWAP

TUNE

ASPECT

CH +

CH –

PLAY FFREW

STOP PAUSE

RM-C1257G

DVD

VCR/DVD

INDEX

SELECT

POWER

C.C.

INPUT

RETURN+

LIGHT

VOL

BACK

TV/VCR

STILL/PAUSE

RM-C1257G

MODELS: AV-30W585 AV-30W575

• For information on remote control buttons, see pages 55 - 63.

Quick Setup Getting Started

Getting Started

These quick setup pages will provide you, in three easy steps, with the basic information you need to begin using your new television right away.

If you have questions, or for more detailed information on any of these steps, please consult other sections of this manual.

Step 1 – The Remote Control

Before you can operate your remote control, you first need to install the batteries (included).

Lift and pull the latch on the back of the remote control to open. Insert two batteries (included) carefully noting the “+” and “–” markings, placing the “–” end in the unit first. Snap the cover back into place.

When you change the batteries, try to complete the task within three minutes. If you take longer than three minutes, the remote control codes for your VCR, DVD, and/or cable box/satellite receiver may have to be reset. See pages 25 - 28.

Key Feature Buttons

MUTING

The four key feature buttons at the center of the remote can be used for basic operation of the television. The top and bottom buttons will scan forward and back through the available channels. To move rapidly through the channels using JVC’s Hyperscan feature, press and hold CH+ or

VOL

–

CH –. The channels will zip by at a rate of five channels per second. The right and left buttons will turn the volume up or down. These buttons are also marked with four arrows and

are used with JVC’s onscreen menu system. To use the onscreen menus, press the M

ENU button.

Basic Operation

Turn the television on and off by pressing the POWER button at the top right corner of the remote. If this is the first time you are turning on the TV, the interactive plug-in menu appears.

• Make sure the TV/CATV switch is set to TV. Move the switch to CATV only if you need to operate a cable box.

• Slide the VCR/DVD selector switch to VCR to control a VCR. Slide to DVD to control a DVD player. Please see pages 25 to 28 for instructions on programming your remote control to operate a cable box, VCR or DVD player.

CH +

CH –

VOL

BACK

POWER

CATV

VCR DVD

Quick Setup Connections

Step 2 – Connecting Your Devices

Please follow the flow chart below to determine which connection setup is right for you. Then, refer to the appropriate diagrams to connect your television to other devices that you may have. After you are finished connecting your devices, plug the power cord into the nearest power outlet and turn on the TV.

A VCR is not necessary for operation of the television. If you follow these diagrams and the television does not work properly, contact your local cable operator.

• To connect a DVD player, see Diagram #3. A DVD player is optional.

• If you have a satellite television system, please refer to the satellite TV manual.

Do you use a Cable TV Box?

Yes

Do you have a VCR? Do you have a VCR?

Yes No Yes No

Diagram #2

Diagram #1 Diagram #3 Diagram #1

Quick Setup Connections

Diagram #1

Cable or Antenna

Output

75Ω

( VHF/UHF )

Coaxial Cable

OUT IN

TV Rear Panel

Cable Box

Note:

• If you do not have a cable box, connect the cable wire from the wall outlet into the back of the TV.

Diagram #2

INPUT 3

INPUT 2

INPUT 1

AUDIO

R L

VIDEO S VIDEO

OVER

TV Rear Panel

75Ω

( VHF/UHF )

Cable or Antenna

OUT OUT

Output

Coaxial Cable

Two-Way Splitter

VCR

OUT

R L V

OUT

OUT IN

Cable Box

Notes:

• If your VCR is a mono sound unit, it will have only one audio out jack. Connect it to the LEFT AUDIO INPUT on the front of the TV.

• Use the S-Video connection if possible for superior picture quality.

• Your VCR must be turned on to view premium cable channels.

Quick Setup Connections

Notes:

• Green, blue and red are the most common colors for DVD cables. Some models may vary colors. Please consult the user’s manual for your DVD player for more information.

• Be careful not to confuse the red DVD cable with the red audio cable. It is best to complete one set of connections (DVD or audio output) before starting the other to avoid accidentally switching the cables.

• You may also connect the DVD player to Input 1.

Diagram #3

Cable or Antenna

Output

Two-Way

Splitter

OUT OUT

75Ω

( VHF/UHF )

TV Rear Panel

INPUT 3

INPUT 2

INPUT 1

Coaxial Cable

R L V

OUT

AUDIO

R L

VIDEO S VIDEO

OVER

AUDIO OUT

R L

OUT

VCR

COMPONENT VIDEO

INPUT 1INPUT 2

OUT

Green

Blue

Red

DVD Player (OPTIONAL)

Quick Setup Connections

Connecting to JVC AV CompuLink

Note: AV-30W585 ONLY

JVC’s AV CompuLink feature makes playing video tapes or DVDs totally automatic. Simply insert a pre-recorded tape into your JVC brand VCR or DVD into your JVC DVD player and the device will automatically turn on and begin playback. At the same time, using the AV CompuLink, the VCR or DVD player sends a signal to the television telling it to turn on and switch to the proper video input.

• The AV CompuLink cable may be included with the JVC AV CompuLink unit you wish to connect. If it is not, contact JVC Parts Department at (800)-882-2345, or www.jvcservice.com for part # EWP 805-012.

• AV CompuLink can only be used with JVC brand products.

AV Compu Link Cable

To Connect: Plug one end of the AV CompuLink cable

into the AV COMPULINK INPUT on your VCR, DVD, or other CompuLink device. Plug the other end of the AV CompuLink cable into the AV COMPULINK at the rear of the television.

Note:

• The AV CompuLink cable has a male 3.5 mm (mono) plug on each end.

TV Rear Panel

COMPULINK

OUT

V L R

VCR

OUT

AV CompuLink

Notes:

• In order for the VCR playback to begin automatically, the recording tabs must be removed from the VHS tape. If the tab is in place, automatic switching will occur when you push the VCR’s Play button.

• If your JVC brand VCR has “A code/B code remote control switching” (see your VCR’s instruction book), using VCR A code will switch the TV to input 1.

• Refer to your DVD instruction book for detailed connection information.

• To connect a JVC HiFi receiver or amplifier for a completely automated home theater, see the receiver connection instructions for detailed connection information.

• AV CompuLink is compatible with select AV CompuLink receivers.

Quick Setup Connections

Connecting to a Camcorder

You may connect a camcorder, game console or other equipment to your television by using the side input jacks (Input 4) located on the side of the television. You can also connect these using the television’s rear input jacks, using the same instructions.

Camcorder

- OR -

INPUT 4

S-VIDEO

OVER

VIDEO

L/MONO

AUDIO

OPERATE

CHANNEL

VOLUME

1) Connect a yellow composite cable from the camcorder VIDEO OUT, into the VIDEO IN on

the side of the TV, OR connect an S-Video cable from the side of the TV to the camcorder.

2) Connect a white cable from the camcorder LEFT AUDIO OUT, into the LEFT AUDIO IN on

the side of the TV.

3) Connect a red cable from the camcorder RIGHT AUDIO OUT, into the RIGHT AUDIO IN on

the side of the TV.

Note:

• If your camcorder is a mono sound model it will have only one AUDIO OUT. Connect it to the

L/MONO on the side of the TV.

Quick Setup Connections

Connecting to an External Amplifier

Subwoofer Out - Use a powered subwoofer with the surround feature to simulate a home theater system. Simply connect the subwoofer to the back of the TV.

TV Rear Panel

SUBWOOFER OUT

AUDIO OUT

R L

Speaker Speaker

Amplifier

Powered

Subwoofer

1) Connect a white cable from the LEFT AUDIO OUTPUT on the back of the TV to the

LEFT AUDIO INPUT on the amplifier.

2) Connect a red cable from the RIGHT AUDIO OUTPUT on the back of the TV to the

RIGHT AUDIO INPUT on the amplifier.

3) Connect a black cable from the SUBWOOFER OUT on the back of the TV to

the LINE INPUT of the subwoofer.

Notes:

• Refer to your amplifier’s manual for more information.

• You can use AUDIO OUTPUT for your home theater system.

Connecting to the Surround Amplifier

In multi-channel sound such as 5.1 channel, the speech characters are played back from the center speaker.

A center speaker in a movie theater is set in back of the screen so it can recreate a conversation scene in the movie more natually. By using your TV's speaker as the center speaker, you can obtain the same sound effect as in a movie theater in you home theater sound system.

TV Rear Panel

Front

Front Surround

CENTER

CHANNEL IN

CENTER CHANNEL OUTPUT

(VARIABLE OUTPUT)

1) Connect the Pin cable from the TV's CENTER CHANNEL INPUT terminal to the surround

amplifier's CENTER CHANNEL OUTPUT terminal.

Note:

• Please read the benefit of this feature on page 47.

Quick Setup Connections

Connecting to a Digital TV Receiver

By connecting a Digital TV Reciever, high definition pictures can be displayed on your TV in their digital form.

DTV Decoder

AUDIO OUTDIGITAL OUT

TV Rear Panel

DIGITAL - IN

AUDIO

(ANALOG)

VIDEO

HDMI to DVI Cable

After the connections have been made,

tighten the screw to secure the cables.

1) Connect the HDMI to DVI Cable from the DIGITAL OUT on the back of your DTV decoder, to the DIGITAL-IN on the back of your television.

2) Connect a red cable from the DTV decoder RIGHT AUDIO OUT, to the RIGHT AUDIO DIGITAL-IN on the back of your television.

3) Connect a white cable from the DTV decoder LEFT AUDIO OUT, to the LEFT AUDIO DIGITAL-IN on the back of your television.

• The digital-in terminal is not compatible with the picture signal of a personal computer.

• Use a HDMI to DVI cable (commercially available) in order to digitally connect the television

with a DTV decoder.

(DIGITAL)

AUDIO

(DIGITAL)

Notes:

• If 480p signals (640x480 or 720x480) are displayed on the screen, the horizontal balance

may be slightly shifted. Access the “DIGITAL-IN” in the initial setup menu to adjust it. (Refer to page 46.)

• When you do the above connection, set DIGITAL-IN AUDIO in the Initial Setup menu to

ANALOG. See "DIGITAL-IN AUDIO", page 46.

Quick Setup Connections

Connecting to a HDMI Compatible Device

By connecting a HDMI compatible device, high definition pictures can be displayed on your TV in their digital form. Some HDMI devices can include DVD players, D-VHS or any HDMI compatible device.

HDMI (High Definition Multimedia Interface) is the first industry supported, uncompressed, all digital audio/video interface. HDMI provides and interface between any audio/video source, such as a set-top box, DVD player, A/V receiver or an audio and/or video monitor, such as a digital television (DTV).

HDMI Compatable Device

DIGITAL OUT

AUDIO OUT

HDMI Cable

TV Rear Panel

DIGITAL - IN

(ANALOG)

(DIGITAL)

AUDIO

VIDEO

AUDIO

1) Connect the HDMI Cable from the DIGITAL OUT on the back of your DTV or HDMI device, to

the DIGITAL-IN on the back of your television.

Note:

• When you do the above connection, set DIGITAL-IN AUDIO in the Initial Setup menu to

DIGITAL. See "DIGITAL-IN AUDIO", page 46.

Quick Setup Connections

Connecting to an AV Receiver using your television's V1 Smart Input

By connecting your AV Receiver to your television's V1 Smart Input, you can watch picture sources from many different devices, without having to change or use the other input connections on your TV. This allows you to free up the other input connections so you can connect more devices to your television.

AV Receiver

MONITOR

OUT

MONITOR OUT

INPUT 3

INPUT 2

INPUT 1

AUDIO

R L

VIDEO S VIDEO

OVER

TV Rear Panel

COMPONENT VIDEO

INPUT 1INPUT 2

1) Connect an S-Video Cable from the AV Receiver's MONITOR OUT, to the S-Video INPUT-1 on the back of your television.

2) Connect a Yellow Component Cable from the AV Receiver's MONITOR OUT, into the VIDEO INPUT-1 on the back of your television.

3) Connect a Green Component Cable from the AV Receiver's Y MONITOR OUT, into the Y VIDEO INPUT-1 on the back of your television.

4) Connect a Blue Component Cable from the AV Receiver's Pb MONITOR OUT, into the Pb VIDEO INPUT-1 on the back of your television.

5) Connect a Red Component Cable from the AV Receiver's Pr MONITOR OUT, into the Pr VIDEO INPUT-1 on the back of your television.

Notes:

• Please refer to your AV Receiver instruction manual for more information on connecting your

speakers and other devices like a DVD player.

• Use your AV Receiver's remote to switch to the different devices you have connected.

• Some AV Receivers may not respond when the V1 Smart Input function is turned on.

• If you have video connections for each input device connected to your AV Receiver, you

should not connect them using both S-Video and Composite connection at the same time when you are using V1 Input as the V1 Smart Input. In this case we recommend using the S-Video connection.

Quick Setup Plug-In Menu

Step 3 – The Interactive Plug In Menu

When you turn your television on for the first time the interactive plug-in menu will appear. The plug-in menu helps you to get your TV ready to use by letting you set your preferences for:

• The language in which you want the onscreen menus to appear.

• Setting the TV’s clock to the correct time so your timer functions will work properly. You can

choose “AUTO” or “MANUAL” for setting the clock.

• The auto tuner setup of which channels you wish to receive.

We recommend you complete the interactive plug-in items before you start using your television.

Language

After the “JVC INTERACTIVE PLUG IN MENU” has been displayed, the TV automatically switches to the LANGUAGE settings. You can choose to view your onscreen menus in three languages: English, French (Français) or Spanish (Español).

√®

LANGUAGE/LANGUE/IDIOMA

ENGLISH

To choose a language:

(English, Français or Español)

†

To NEXT (To set clock)

SELECT OPERATE EXIT

(To be continued...)

+ 50 hidden pages