JVC KS-FX722RE Instructions Manual

CASSETTE RECEIVER

ENGLISH

CASSETTEN-RECEIVER
RADIOCASSETTE
RADIO/CASSETTESPELER

KS-FX722R

DEUTSCH

FRANÇAIS

DISP

TP
RDS

PTY

8 9 10 11 127

DAB

MO

NEDERLANDS

For installation and connections, refer to the separate manual.
Für den Einbau und die Anschlüsse siehe das eigenständige Handbuch.
Pour l’installation et les raccordements, se référer au manuel séparé.
Bijzonderheden over de installatie en aansluiting v an het apparaat vindt u in de desbetreffende
handleiding.

INSTRUCTIONS

BEDIENUNGSANLEITUNG

MANUEL D’INSTRUCTIONS

GEBRUIKSAANWIJZING

GET0010-001A

[E]

Thank you for purchasing a JVC product. Please read all instructions carefully before operation,

to ensure your complete understanding and to obtain the best possible performance from the unit.

CONTENTS

How to reset your unit............................... 2

LOCATION OF THE BUTTONS............ 3

ENGLISH

Control panel ........................................... 3

BASIC OPERATIONS ...................... 4

Turning on the power................................ 4

RADIO BASIC OPERATIONS ............. 5

Listening to the radio ................................ 5

Storing stations in memory ....................... 6

Tuning into a preset station ...................... 7

RDS OPERATIONS ........................ 8

What you can do with RDS EON.............. 8

Other convenient RDS functions and

adjustments........................................... 11

TAPE OPERATIONS ....................... 14

Listening to a cassette.............................. 14

Finding the beginning of a tune ................ 15

Other convenient tape functions............... 16

SOUND ADJUSTMENTS .................. 17

Adjusting the sound ................................. 17

Using the sound control memory ............. 17

Storing your own sound adjustments ....... 18

OTHER MAIN FUNCTIONS ............... 19

Setting the clock ...................................... 19

Changing the general settings (PSM) ...... 19

Detaching the control panel...................... 22

CD CHANGER OPERATIONS ............. 23

Playing CDs ............................................. 23

Selecting CD playback modes.................. 24

EXTERNAL COMPONENT OPERATIONS .. 25

Playing an external component ................ 25

DAB TUNER OPERATIONS ............... 26

Tuning into an ensemble and one of the

services ................................................. 26

Storing DAB services in memory ............. 27

Tuning into a preset DAB service ............. 28

TROUBLESHOOTING...................... 29

MAINTENANCE ............................ 30

SPECIFICATIONS .......................... 31

How to reset your unit

Press and hold both the SEL (select) and (standby/on/attenuator) buttons at the same
time for several seconds.
This will reset the built-in microcomputer.

Note:

Your preset adjustments – such as preset channels or
sound adjustments – will also be erased.

Note:

For security reasons, a numbered ID card is provided with this unit, and the same ID number is imprinted on
the unit’s chassis. Keep the card in a safe place, as it will help the authorities to identify your unit if stolen.

BEFORE USE

*

*

For safety....

• Do not raise the volume level too much, as this will
block outside sounds, making driving dangerous.

• Stop the car before performing any complicated
operations.

Temperature inside the car....

If you have parked the car for a long time in hot or
cold weather, wait until the temperature in the car
becomes normal before operating the unit.

(standby/on/attenuator)

SEL (select)

2

Control panel

LOCATION OF THE BUTTONS

Display window

i

o

1

;

3245

DISP

TP
RDS

PTY

8 9 10 11 127

6

a

s

df

j

78 9

DAB

MO

ENGLISH

g

k lh

p

q

1 (standby/on/attenuator) button
2 Control dial
3 DISP (display) button
4 TP (traffic programme)

RDS (radio data system) button

5 PTY (programme type) button
6 Cassette compartment
7 FM AM button

• Also functions as the DAB button.

8 TAPE 23 button
9 0 (eject) button
p ¢ / 4 buttons

•

Also functions as SSM buttons when pressed
together.

q SEL (select) button
w Number buttons
e RPT (repeat) button

• Also functions as ∞ (DAB service selection).

r RND (random) button

• Also functions as 5 (DAB service selection) or
MO (monaural).

w

yuret

t SCM (sound control memory) button
y CD-CH (CD changer) button
u (control panel release) button

Display window

i Volume (or audio) level indicator
o SCM indicator
; Main display
a MO (monaural) indicator
s RND (random) indicator
d RPT (repeat) indicator
f LOUD indicator
g FM band number indicators

FM1, FM2, FM3

h Sound mode indicators

BEAT, SOFT, POP

j RDS indicators

AF, EON, REG, TP, PTY

k CD-CH (CD changer) indicator
l AM band indicator

3

BASIC OPERATIONS

ENGLISH

3

1

Turning on the power

1

Turn on the power.

Note on One-Touch Operation:

When you select a source in step 2 below, the
power automatically comes on. You do not have
to press this button to turn on the power.

2

Select the source.

DISP

TP
RDS

PTY

8 9 10 11 127

DAB

MO

2

3

Adjust the volume.

To increase the volume.

To decrease the volume.

Volume level indicator

Volume level appears.

To operate the tuner (FM or AM),

see pages 5 – 13.

To operate the tape,

see pages 14 – 16.

To operate the CD changer,

see pages 23 – 24.

To operate the external component,

see page 25.

To operate the DAB tuner,

see pages 26 – 28.

4

Adjust the sound as you want.
(See page 17.)

To drop the volume in a moment

Press briefly while listening to any
source. “ATT” starts flashing on the display, and
the volume level will drop in a moment.
To resume the previous volume level, press the
button briefly again.

• If you turn the control dial clockwise, you can
also restore the sound.

To turn off the power

Press and hold until “SEE YOU” appears
on the display.

Note:

When you use this unit for the first time, set the built-in
clock correctl y, see page 19.

4

RADIO BASIC OPERATIONS

DISP

TP
RDS

PTY

8 9 10 11 127

Listening to the radio

You can use either automatic searching or manual
searching to tune into a particular station.

Searching a station automatically:
Auto search

1

Select the band (FM1 – 3, AM).

FM1 FM2 FM3 AM

DAB

MO

T o stop searching before a station is received,

press the same button you have pressed for
searching.

Searching a station manually:
Manual search

1

Select the band (FM1 – 3, AM).

FM1 FM2 FM3 AM

ENGLISH

Selected band appears.

Audio (see page 21) or volume level indicator

Note:

This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to an
FM broadcast.

2

Start searching a station.

Press ¢ to search
stations of higher
frequencies.

Press 4 to search
stations of lower
frequencies.

When a station is received, searching
stops.

Note:

This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to an
FM broadcast.

2

Press and hold ¢ or 4 until
“M” (manual) starts flashing on the
display.

Selected band appears.

CONTINUED ON THE NEXT PAGE

5

3

T une into a station y ou want while “M”
is flashing.

ENGLISH

• If you release your finger from the button,
the manual mode will automatically turn off
after 5 seconds.

• If you hold down the button, the frequency
keeps changing (in 50 kHz intervals for FM
and 9 kHz intervals for AM – MW/LW) until
you release the button.

Press ¢ to tune
into stations of higher
frequencies.

Press 4 to tune
into stations of lower
frequencies.

Storing stations in memory

You can use one of the following two methods to
store broadcasting stations in memory.

• Automatic preset of FM stations: SSM (Strong­station Sequential Memory)

• Manual preset of both FM and AM stations

FM station automatic preset: SSM

Y ou can preset 6 local FM stations in each FM band
(FM1, FM2 and FM3).

1

Select the FM band (FM1 – 3) you want
to store FM stations into.

Each time you press the
button, the FM band
changes as follows:

When an FM stereo broadcast is hard to
receive:

Press MO RND (monaural/random) while
listening to an FM stereo broadcast.

• Each time you press the button, the MO
indicator lights up and goes off alternately.

Lights up when receiving
an FM broadcast in stereo.

MO

When the MO indicator is lit on the display, the
sound you hear becomes monaural but the
reception will be improved (the ST indicator
goes off).

FM1 FM2 FM3 AM

2

Press and hold both buttons for more
than 2 seconds.

“SSM” appears, then disappears when automatic
preset is over.

Local FM stations with the strongest signals are
searched and stored automatically in the band
number you have selected (FM1, FM2 or FM3).
These stations are preset in the number buttons —
No.1 (lowest frequency) to No .6 (highest frequency).
When automatic preset is over, the station stored
in number button 1 will be automatically tuned into.

6

Manual preset

You can preset up to 6 stations in each band (FM1,
FM2, FM3 and AM) manually.

Ex.: Storing an FM station of 88.3 MHz into the

preset number 1 of the FM1 band

1

Select the band (FM1 – 3, AM) you
want to store stations into (in this
example, FM1).

Each time you press the
button, the FM band
changes as follows:

FM1 FM2 FM3 AM

2

Tune into a station of 88.3 MHz.

Press ¢ to tune
into stations of higher
frequencies.

Notes:

• A previously preset sta tion is erased when a new station
is stored in the same preset number.

• Preset stations are erased when the power supply to
the memory circuit is interrupted (for e xample, during
battery replacement). If this occurs, pr eset the stations
again.

Tuning into a preset station

You can easily tune into a preset station.
Remember that you must store stations first. If you
have not stored them yet, see “Storing stations in
memory” on page 6.

1

Select the band (FM1 – 3, AM).

FM1 FM2 FM3 AM

ENGLISH

Press 4 to tune
into stations of lower
frequencies.

3

Press and hold the number button
(in this example, 1) for more than 2
seconds.

7

“P 1” flashes for a few seconds.

4

Repeat the above procedure to store
other stations into other preset
numbers.

2

Select the number (1 – 6) for the preset
station you want.

8 9 10 11 127

7

RDS OPERATIONS

What you can do with RDS EON

RDS (Radio Data System) allows FM stations to
send an additional signal along with their regular
programme signals. For e xample, the stations send

ENGLISH

their station names, as well as information about
what type of programme they broadcast, such as
sports or music, etc.
Another advantage of RDS function is called “EON
(Enhanced Other Networks).” The EON indicator
lights up while receiving an FM station with the EON
data. By using the EON data sent from a station,
you can tune into a different station of a different
network broadcasting your favorite programme or
traffic announcement while listening to another
programme or to another source such as tape.

By receiving the RDS data, this unit can do the
following:

• Tracing the same programme automatically
(Network-Tracking Reception)

• Standby Reception of TA (Traffic
Announcement) or your favorite programme

• PTY (Programme Type) search

• Programme search

• And some other functions

To use Network-Tracking Reception, press and
hold TP RDS (Traffic Programme/Radio Data
System) for more than 1 second. Each time you
press and hold the button, Network-Tracking
Reception modes change as follows:

TP
RDS

Mode 1

The AF indicator lights up but the REG indicator
does not.
Network-Tracking Reception is activated with
Regionalization set to “off.”
Switches to another station within the same
network when the receiving signals from the
current station become weak.

• In this mode, the programme may differ from the one

currently received.

Mode 1

Mode 2 Mode 3

AF indicator

REG indicator

Tracing the same programme
automatically (Network-Tracking
Reception)

When driving in an area where FM reception is not
good, the tuner built in this unit automatically tunes
into another RDS station, broadcasting the same
programme with stronger signals. So, you can
continue to listen to the same programme in its
finest reception, no matter where you drive. (See
the illustration on the next page.)
Two types of the RDS data are used to make
Network-Tracking Reception work correctly — PI
(Programme Identification) and AF (Alternative
Frequency).
Without receiving these data correctly from the RDS
station you are listening to, Network-Tracking
Reception will not operate.

Mode 2

Both the AF indicator and the REG indicator light
up.
Network-Tracking Reception is activated with
Regionalization set to “on.”
Switches to another station, within the same
network, broadcasting the same programme
when the receiving signals from the current
station become weak.

Mode 3

Neither the AF indicator nor the REG indicator
lights up.
Network-Tracking Reception is deactivated.

8

The same programme can be received on
different frequencies.

Programme 1
broadcasting
on frequency A

Programme 1
broadcasting
on frequency B

Programme 1
broadcasting
on frequency C

Programme 1
broadcasting
on frequency E

Programme 1
broadcasting
on frequency D

Using Standby Reception

PTY Standby Reception

When you press PTY while listening

PTY

to an FM station, the PTY indicator is
lit during reception of a PTY station
and the PTY standby mode is
engaged. The selected PTY name
stored on page 10 flashes for 5
seconds.

• When the station being received is not a PTY station,
the PTY indicator flashes. Press ¢ or 4
to engage the PTY standby mode. “SEARCH” appears
on the display, and PTY station search starts. When a
PTY station is tuned into, the PTY indicator is lit.

7 If you are listening to a tape or other connected

components and wish to listen to a selected PTY
broadcast, press PTY to enter the PTY standby
mode. (The PTY indicator lights up.)

ENGLISH

Standby Reception allows the unit to switch
temporarily to your favorite programme (PTY:
Programme Type) and Traffic Announcement (TA)
from the current source (another FM station, tape
or other connected components).

• Standby Reception will not work if you are listening

to an AM station.

TA Standby Reception

TP

When you press TP RDS while listening

RDS

to an FM station, the TP indicator is lit
during reception of a TP (Traffic
Programme) station and the TA standby
mode is engaged.

• When the station being received is not a TP station,

the TP indicator flashes. Press ¢ or 4 to
engage the T A standby mode. “SEARCH” appears on
the display, and TP station search starts. When a TP
station is tuned into, the TP indicator is lit.

7 If you are listening to a tape or other connected

components and wish to listen to a TP station,
press TP RDS to enter the T A standb y mode. (The
TP indicator lights up.)

If the selected PTY programme starts broadcasting
while the PTY standby mode is active, the selected
PTY name appears and the playback source
changes to the FM band. The selected PTY
programme can then be heard.

T o deactivate the PTY standby mode, press PTY
again.

If a traffic programme starts broadcasting while the
T A standb y mode is active, “TRAFFIC” appears and
the playback source changes to the FM band. The
volume increases to the preset T A volume le vel (see
page 12) and the traffic programme can be heard.

To deactivate the TA standby mode, press TP
RDS again.

9

Selecting your favorite programme for
PTY Standby Reception

You can select your favorite programme for PTY
Standby Reception to store in memory.

ENGLISH

When shipped from the factory, “NEWS” is stored
as the programme type for PTY Standb y Reception.

1

Press and hold SEL (select) for more
than 2 seconds so that one of the
PSM items appears on the display.
(PSM: see page 20.)

2

Select “PTY STBY” (standby) if not
shown on the display.

Searching your favorite programme

You can search one of your 6 favorite programme
types stored in memory.
When shipped from the factory, the following 6
programme types hav e been stored in the number
buttons (1 to 6).
To store your favorite programme types, see
below.
To search your favorite programme type, see
page 11.

1

POP M

45

CLASSICS

2

ROCK M EASY M

AFFAIRS

To store your favorite programme types

1

Press and hold SEL (select) for more
than 2 seconds so that one of the PSM
items appears on the display.
(PSM: see page 20.)

3

6

VARIED

3

Select one of twenty-nine PTY codes.
(See page 13.)

Selected code name
appears on the display
and is stored into memory.

4

Press SEL (select) to finish the setting.

2

Select “PTY SRCH” (search) if not
shown on the display.

3

Select one of twenty-nine PTY codes.
(See page 13.)

Selected code name
appears on the display.

• If the code already stored
in memory is selected, it
will flash on the display.

10

4

Press and hold the number button for
more than 2 seconds to store the PTY
code selected into the preset number
you want.

8 9 10 11 127

The selected code name will flash on the
display.

• If there is a station broadcasting a programme of
the same PTY code you selected, that station is
tuned into.

• If there is no station broadcasting a programme
of the same PTY code you selected, the station
will not change.

Note:

In some areas, the PTY search will not work correctly.

ENGLISH

5

Press SEL (select) to finish the setting.

To search your favorite programme type

1

Press and hold PTY (programme type)
for more than 1 second while listening
to an FM station.

PTY

The last selected PTY code appears.

2

Select one of the PTY codes stored in
the preset number buttons (1 to 6).

8 9 10 11 127

Ex.: When “ROCK M” is stored in preset number

button 2

PTY search for your favorite programme
starts after 5 seconds.

Other convenient RDS functions
and adjustments

Automatic selection of the station
when using the number buttons

Usually when you press the number button, the
preset station is tuned into.
Howev er, when the preset station is an RDS station,
something different will happen. If the signals from
that preset station are not sufficient for good
reception, this unit, using the AF data, tunes into
another frequency broadcasting the same
programme as the original preset station is
broadcasting. (Programme search)

T o activate prog ramme search, follow the procedure
below .

• Programme search takes a while.

• See also “Changing the general settings (PSM)”
on page 19.

1 Press and hold SEL (select) for more than 2

seconds so that one of the PSM items appears
on the display.

2 Press ¢ or 4 to select

“P(Programme)-SEARCH.”

3 Turn the control dial clockwise to select “ON.”

Now programme search is activated.

To cancel programme search, repeat the same
procedure and select “OFF” in step 3 by turning
the control dial counterclockwise.

11

Changing the display mode while
listening to an FM station

You can change the initial indication on the display
to station name (PS NAME), station frequency
(FREQ) or clock time (CLOCK), while listening to

ENGLISH

an FM RDS station.

• See also “Changing the general settings (PSM)”
on page 19.

1 Press and hold SEL (select) for more than 2

seconds so that one of the PSM items appears
on the display.

2 Press ¢ or 4 to select “DISPMODE”

(display mode).

3 T urn the control dial to set to the desired indication

(“PS NAME,” “FREQ” or “CLOCK”).

Note:

By pressing DISP, you can also change the display while
listening to an FM RDS station.
Each time you press the b utton, the following information
appears on the display:

Station name

(PS NAME)

Programme type

(PTY)

Station frequency

(FREQ)

Clock time

(CLOCK)

Setting the TA volume level

You can preset the volume level for TA Standby
Reception. When a traffic programme is received,
the volume lev el automatically changes to the preset
level.

• See also “Changing the general settings (PSM)”
on page 19.

1 Press and hold SEL (select) for more than 2

seconds so that one of the PSM items appears
on the display.

2 Press ¢ or 4 to select “TA VOL.”
3 T urn the control dial to set to the desired volume.

You can set it from “VOL 00” to “VOL 50.”

Automatic clock adjustment

When shipped from the factory, the clock built in
this unit is set to be readjusted automatically using
the CT (Clock Time) data in the RDS signal.
If you do not want to use automatic clock
adjustment, follow the procedure below.

• See also “Changing the general settings (PSM)”
on page 19.

1 Press and hold SEL (select) for more than 2

seconds so that one of the PSM items appears
on the display.

2 Press ¢ or 4 to select “AUTO ADJ.”
3 Turn the control dial counterclockwise to select

“OFF.”
Now automatic clock adjustment is canceled.

T o reactivate c lock adjustment, repeat the same
procedure and select “ON” in step 3 b y turning the
control dial clockwise.

• Then, the display goes back to the original indication

in several seconds.

12

Note:

It takes about 2 minutes to adjust the time using the CT
data. So, you should not change the station for more
than 2 minutes continuously; otherwise, the clock time
will not be adjusted.

PTY codes

NEWS: News
AFFAIRS: Topical programmes expanding

on current news or affairs

INFO: Programmes which impart advice

on a wide variety of topics
SPORT: Sport events
EDUCATE: Educational programmes
DRAMA: Radio plays
CULTURE: Programmes on national or

regional culture
SCIENCE: Programmes on natural science

and technology
VARIED: Other programmes like comedies

or ceremonies
POP M: Pop music
ROCK M: Rock music
EASY M: Easy-listening music
LIGHT M: Light music
CLASSICS: Classical music
OTHER M: Other music
WEATHER: Weather information
FINANCE: Reports on commerce, trading,

the Stock Market, etc.
CHILDREN: Entertainment programmes for

children

SOCIAL: Programmes on social activities
RELIGION: Programmes dealing with any

aspect of belief or faith, or the
nature of existence or ethics

PHONE IN: Programmes where people can

express their views either by
phone or in a public forum

TRAVEL: Programmes about travel

destinations, package tours, and
travel ideas and opportunities

LEISURE: Programmes concerned with

recreational activities such as

gardening, cooking, fishing, etc.
JAZZ: Jazz music
COUNTRY: Country music
NATION M: Current popular music from

another nation or region, in that

country’s language
OLDIES: Classic pop music
FOLK M: Folk music
DOCUMENT: Programmes dealing with factual

matters, presented in an

investigative style

ENGLISH

13

TAPE OPERATIONS

ENGLISH

Listening to a cassette

1

Insert a cassette into the cassette
compartment.

The unit turns on and tape
play starts automatically.
When one side of the tape
reaches its end during play,
the other side of the tape
automatically starts playing.
(Auto Reverse)

Note on One-Touch Operation:

When a cassette is already in the cassette
compartment, pressing TAPE 23 turns on the
unit and tape play starts automatically.

DISP

TP
RDS

PTY

8 9 10 11 127

DAB

MO

To fast-forward and rewind a tape

Press ¢ for more than 1
second to fast-forward the tape.
When the tape reaches its end,
the tape is reversed and playback
starts from the beginning of the
other side.

Press 4 for more than 1
second to rewind the tape.
When the tape reaches its end,
playback of the same side starts.

To stop fast forward or rewind at any position
on the tape, press TAPE 23.

Tape play starts from that position on the tape.

2

Select the tape direction.

Each time you press
TAPE 23, the tape direction
changes alternately
forward ( ) and
reverse ( ).

To stop play and eject the cassette

Press 0.
Tape play stops and the cassette automatically
ejects from the cassette compartment. The
source changes to the previously selected one.
If you change the source, tape play also stops
(without ejecting the cassette this time).

• You can also eject the cassette by pressing 0
while the unit is turned off.

Note:

When the tape reaches its end while fast-forwar ding, the
tape direction will be changed automatically.

14

Prohibiting cassette ejection

You can prohibit cassette ejection and can “lock”
a cassette in the cassette compartment.
Press and hold TAPE 23 and 0 for more than 2
seconds. “NO EJECT” flashes on the display for
about 5 seconds, and the cassette is “locked.”

Finding the beginning of a tune

Multi Music Scan allows you to automatically start
playback from the beginning of a specified tune.
You can specify up to 9 tunes ahead of or before
the current tune.

During playback

Specify how many tunes ahead of or
before the current tune the one you want
is located.

ENGLISH

To cancel the prohibition and “unlock” the
cassette, press and hold TAPE 23 and 0 for

more than 2 seconds again. “EJECT OK” flashes
for about 5 seconds, and this time the cassette is
“unlocked.”

Note:

If you press 0 while cassette ejection is prohibited,
the cassette will not be ejected.

Press ¢ to locate a tune
ahead of the current tune on
the cassette.

Press 4 to locate a tune
before the current tune on the
cassette.

Each time you press the buttons, the number
changes up to ±9.
When the beginning of the specified tune is
located, playback starts automatically.

Notes:

• While locating a specified tune:
– If the tape is rewound to its beginning, playback

starts from the beginning of that side.

– If the tape is fast-forwarded to the end, it is

reversed and played from the beginning of the
other side.

• In the following cases, the Multi Music Scan
function may not operate correctly:
– Tapes with tunes having long pianissimo passages

(very quiet parts) or non-recor ded portions between

tunes.
– Tapes with short non-recorded sections.
– Tapes with high level of noise or humming between

tunes.

15

Other convenient tape functions

Skipping the blank portions on the tape

Playing the current tune repeatedly

You can play the current tune repeatedly (Repeat

Play).

You can skip blank portions between the tunes

ENGLISH

(Blank Skip).
When this function is on, the unit skips blank
portions of 15 seconds or more, fast-forwards to
the next tune, then starts playing it.

• See also “Changing the general settings (PSM)”
on page 19.

1

Press and hold SEL (select) for more
than 2 seconds so that one of the
PSM items appears on the display.
(PSM: see page 20.)

2

Press ¢ or 4 to select
“B. SKIP” (blank skip).

3

Turn the control dial clockwise to
select “ON.”

Now Blank Skip is activated.

Press RPT while playing a tune you
want to hear over again.

Each time you press the button,
Repeat Play turns on and off
alternately.

Lights up when Repeat Play is turned on.

When the tune has been played, the tape is
automatically rewound to the beginning of that
tune and the same tune will be played again.

To cancel Repeat Play, press RPT again so that
the RPT indicator goes off.

Note:

In the following cases, Blank Skip and Repeat Play
may not operate correctly:

– Tapes with tunes having long pianissimo passages

(very quiet parts) or non-recorded portions during

tunes.
– Tapes with short non-recorded sections.
– Tapes with high level noise or humming between

tunes.
– Tapes with tunes recorded at low recording levels.

4

Press SEL (select) to finish the
setting.

T o cancel Blank Skip, repeat the same procedure

and select “OFF” in step 3 by turning the control
dial counterclockwise.

16

Adjusting the sound

SOUND ADJUSTMENTS

2

Adjust the level.

You can adjust the sound characteristics to your
preference.

1

Select the item you want to adjust.

Each time you press the button,
the adjustable items change as
follows:

BAS

(bass)

VOL

(volume)

Indication To do: Range

BAS Adjust the bass. –06 (min.)

TRE Adjust the treble. –06 (min.)

FAD* Adjust the front R06 (Rear only)

and rear speaker |
balance. F06 (Front only)

BAL Adjust the left L06 (Left only)

and right speaker |
balance. R06 (Right only)

LOUD Boost low and high

frequencies to
produce a well­balanced sound
at low volume
level.

VOL Adjust the volume. 00 (min.)

* If you are using a two-speaker system, set the fader

level to “00.”

TRE

(treble)

LOUD

(loudness)

FAD

(fader)

BAL

(balance)

|
+06 (max.)

|
+06 (max.)

LOUD ON
|
LOUD OFF

|
50 (max.)

To increase the level.

ENGLISH

To decrease the level.

Note:

Normally, the control dial works as the volume
control. So you do not have to select “VOL” to adjust
the volume level.

Using the sound control memory

You can select and store a preset sound
adjustment suitable for each playback source

(Advanced SCM).

Selecting and storing the sound modes

Once you select a sound mode, it is stored in
memory. It will be recalled every time you select
the same source and will be shown on the display.
A sound mode can be stored for each of the
following sources — FM1, FM2, FM3, AM, tape
and external components.

• If you do not want to store the sound mode
separately for each playback source, but want
to use the same sound mode for all the sources,
see “To cancel Advanced SCM – SCM LINK” on
page 21.

Select the sound mode you want.

Each time you press the button, the
sound mode changes as follows:

BEAT SOFT POP

SCM OFF

17

• When “SCM LINK” is set to “LINK ON,” the
selected sound mode can be stored in memory
for the current source and the eff ect applies only
to the current source. Each time you change the
playback source, the SCM indicator flashes on

ENGLISH

the display.

• When “SCM LINK” is set to “LINK OFF,” the
selected sound mode effect applies to any source .

Indication For: Preset values

BAS TRE LOUD

BEAT Rock or disco +02 00 ON

music

SOFT Quiet +01 –03 OFF

background

music
POP Light music +04 +01 OFF
SCM OFF (Flat sound) 00 00 ON

Recalling the sound modes

When “SCM LINK” is set to “LINK ON,”
select the source.

Storing your own sound
adjustments

You can adjust the sound modes (BEAT, SOFT,
POP) to your preference and store your own
adjustments in memory.

• There is a time limit in doing the following
procedure. If the setting is canceled before you
finish, start from step 1 again.

1

Call up the sound mode you want to
adjust.

• See the left column for
details.

2

Select “BAS” (bass), “TRE” (treble) or
“LOUD” (loudness).

The sound mode stored in memory for the
selected source is recalled.

Notes:

• You can adjust each sound mode to your preference,
and store it in memory.

If you want to adjust and store your original sound
mode, see “Storing your own sound adjustments”
on the right column.

• To adjust the bass and treble reinforcement levels or
to turn on/off the loudness function temporarily, see
page 17. (Your adjustments will be canceled if
another source is selected.)

3

Adjust the bass or treble level or turn
the loudness function ON/OFF.

• See page 17 for details.

4

Repeat steps 2 and 3 to adjust the
other items.

5

Press and hold SCM until the sound
mode you have selected in step 1
flashes on the display.

Your adjustment made for the
selected sound mode is stored in
memory.

6

Repeat the same procedure to store
other sound modes.

To reset to the factory settings

18

Repeat the same procedure and reassign the
preset values listed in the table on the left
column.

OTHER MAIN FUNCTIONS

Setting the clock

Y ou can also set the cloc k system to either 24 hours
or 12 hours.

1

Press and hold SEL (select) for more
than 2 seconds so that one of the PSM
items appears on the display.
(See page 20.)

2

Set the hour.

1 Select “CLOCK H” if not shown on the

display.

2 Adjust the hour.

1

2

To check the current clock time or change the
display mode

Press DISP repeatedly. Each time you press the
button, the display mode changes as follows:

• During tuner operation:

Clock Frequency

Notes:

* For the indication change during RDS operation,

see page 12.

* For the indication change during DAB operation,

see page 27.

• During tape operation:

ClockPlay mode (tape direction)

• During external component operation:

LINE IN

• During CD changer operation:

Clock

Elapsed playing time

Clock

Disc number

ENGLISH

3

Set the minute.

1 Select “CLOCK M. ”
2 Adjust the minute.

1

4

Set the clock system.

1 Select “24H/12H.”
2 Select “24H” or “12H.”

12

5

Press SEL (select) to finish the setting.

2

Changing the general settings
(PSM)

You can change the items listed on the next page
by using the PSM (Preferred Setting Mode) control.

Basic Procedure

1

Press and hold SEL (select) for more
than 2 seconds so that one of the PSM
items appears on the display.
(See page 20.)

2

Select the PSM item you want to
adjust. (See page 20.)

T o check the current cloc k time while the unit
is turned off, press DISP (display).

The power turns on, the clock time is shown f or
5 seconds, then the power turns off.

CONTINUED ON THE NEXT PAGE

19

3

Adjust the PSM item selected.

ENGLISH

Preferred Setting Mode (PSM) items

4

Repeat steps 2 and 3 to adjust the
other PSM items if necessary.

5

Press SEL (select) to finish the setting.

1

Hold.

CLOCK H Hour adjustment
CLOCK M Min ute adjustment
SCM LINK Sound control

24H/ 12H 24/12-hour time

AUTO ADJ Automatic clock

DISPMODE Display mode

CH DISP Changer display
PTY STBY PTY standby
PTY SRCH PTY search
TA V O L Traffic announcement

2

Select.

memory linkage

display

setting

volume

3

Set.

Counter­clockwise

Back

Back

LINK OFF

12H

OFF

PS NAME

CLOCK

29 programme types

(see pages 10 and 13.)

VOL 00 – VOL 50

Advance
Advance

LINK ON

Factory­preset
settings

Clockwise

LINK ON

24H24H

ON

FREQ

DISCTIME DISC 21

ON

PS NAME 12

(See page 10.)

See
page

17, 21

190:00

19

12

10NEWS

10
12VOL 20

P-SEARCH Programme search
LEVEL Level display

TEL Telephone muting

B. SKIP Blank skip
EXT IN* External component

• Press SEL (select) to finish the setting.

* Displayed only when one of the following sources is selected – FM, AM and Tape.

20

OFF ON

AUDIO 1

OFF

OFF MUTING 1

MUTING 2

AUDIO 2

OFF

AUDIO 2 21

OFFONOFF 16

CHANGER 21, 25LINE INCHANGER

11

21OFF

To cancel Advanced SCM – SCM LINK

You can cancel the Advanced SCM (Sound Control
Memory), and unlink the sound modes and the
playback sources.
When shipped from the factory, a different sound
mode can be stored in memory for each source so
that you can change the sound modes simply by
changing the sources.

• LINK ON: Advanced SCM (different sound
modes for different sources).

• LINK OFF: Conventional SCM (one sound
mode for all sources).

To select the telephone muting – TEL

This mode is used when a cellular phone system is
connected. Depending on the phone system used,
select either “MUTING 1” or “MUTING 2, ” whichev er
mutes the sounds from this unit.
When shipped from the factory, this mode is
deactivated.

• MUTING 1: Select this if this setting can mute
the sounds.

• MUTING 2: Select this if this setting can mute
the sounds.

• OFF: Cancels the telephone muting.

ENGLISH

To select the changer display – CH DISP

You can change the initial indication on the display
either to disc number or to elapsed playing time, while
using the CD changer.
When shipped from the factory, “DISC” is selected.

• DISC: Shows the disc number and track
number.

• TIME: Shows the elapsed playing time.

To select the level meter – LEVEL

You can select the level display according to y our
preference.
When shipped from the factory, “AUDIO 2” is
selected.

• AUDIO 1:

• AUDIO 2:

• OFF:

Level meter illuminates from bottom
to top.
Alternates level meter (moves from
bottom to top) and illumination
display.
Erases the audio level indicator.

To select the external component to use
– EXT IN

You can connect the external component to the CD
changer jack on the rear using the Line Input Adaptor
KS-U57 (not supplied).
To use the external component as the playback
source through this unit, you need to select which
component – CD changer or external component –
to use.
When shipped from the factory, CD changer is
selected as the external component.

• LINE IN: To use the external component other
than CD changer.

• CHANGER: To use the CD changer.

Note:

For connecting the Line Input Adaptor KS-U57 and the
external component, refer to the Installa tion/Connection
Manual (separate volume).

21

Detaching the control panel

You can detach the contol panel when leaving the
car.
When detaching or attaching the control panel,

ENGLISH

be careful not to damage the connectors on the
back of the control panel and on the panel holder .

Detaching the control panel

Before detaching the control panel, be sure to turn
off the power.

1

Unlock the control panel.

Attaching the control panel

1

Insert the left side of the control panel
into the groove on the panel holder.

2

Press the right side of the control
panel to fix it to the panel holder.

2

Pull the control panel out of the unit.

3

Put the detached control panel into the
provided case.

Note on cleaning the connectors:

If you frequently detach the control panel, the
connectors will deteriorate.
T o minimize this possibility, periodically wipe the
connectors with a cotton swab or cloth moistened
with alcohol, being careful not to damage the
connectors.

Connectors

22

CD CHANGER OPERATIONS

DISP

TP
RDS

PTY

8 9 10 11 127

We recommend that you use one of the CH-X series
with your unit.
If you have another CD automatic changer , consult
your JVC IN-CAR ENTERTAINMENT dealer for
connections.

• For example, if your CD automatic changer is one of
the KD-MK series, you need a cord (KS-U15K) for
connecting it to this unit.

Before operating your CD automatic changer:

• Refer also to the Instructions supplied with your
CD changer.

• If no discs are in the magazine of the CD
changer or the discs are inserted upside down,
“NO DISC” will appear on the display. If this
happens, remove the magazine and set the
discs correctly.

• If “RESET 1” - “RESET 8” appears on the
display, something is wrong with the
connection between this unit and the CD
changer. If this happens, chec k the connection
and make sure the cords are connected firmly .
Then, press the reset button of the CD
changer.

DAB

ENGLISH

MO

Playing CDs

Select the CD automatic changer (CD-CH).

Playback starts from the first track
of the first disc.
All tracks of all discs are pla yed back.

• “DISC” or “TIME” can be selected in the general
settings mode. (See page 20.)

When “DISC” is selected

Disc number

Track number

When “TIME” is selected

Elapsed playing time

Note on One-Touch Operation:

When you press CD-CH, the power automatically turns
on. You do not have to press to turn on the
power.

To fast-forward or reverse the track

Press and hold ¢ , while
playing a CD, to fast-forward the

.

track.

Press and hold 4 , while
playing a CD, to reverse the
track.

23

To go to the next track or the previous tracks

Selecting CD playback modes

Press ¢ briefly, while
playing a CD, to go ahead to
the beginning of the next track.

ENGLISH

Each time you press the button
consecutively, the beginning of
the next track is located and
played back.

Press 4 briefly, while
playing a CD, to go back to the
beginning of the current track.
Each time you press the button
consecutively, the beginning of
the previous tracks is located
and played back.

To go to a particular disc directly

Press the number button corresponding to the disc
number to start its playback (while the CD changer
is playing).

8 9 10 11 127

To play back tracks at random (Random Play)

MO

Mode

RND1 Lights All tracks of the current
(random1) disc, then the tracks of

RND2 Flashes All tracks of all discs
(random2) inserted in the magazine.

Each time you press the button, CD
random play mode changes as
follows:

RND1 RND2

Canceled

RND
Indicator

Plays at random

the next disc, and so on.

To play back tracks repeatedly (Repeat Play)

Each time you press the button, CD
repeat play mode changes as
follows:

• To select a disc number from 1 – 6:
Press 1 (7) – 6 (12) briefly.

• To select a disc number from 7 – 12:
Press and hold 1 (7) – 6 (12) for more than 1
second.

Ex. When disc number 3 is selected

Disc number

Track number

RPT1 RPT2

Canceled

Mode

RPT1 Lights The current track (or
(repeat1) specified track).

RPT2 Flashes All tracks of the current
(repeat2) disc (or specified disc).

RPT
Indicator

Plays
repeatedly

24

EXTERNAL COMPONENT OPERATIONS

DISP

TP
RDS

PTY

8 9 10 11 127

Playing an external component

You can connect the external component to the
CD changer jack on the rear using the Line Input
Adaptor KS-U57 (not supplied).

Preparations:

• For connecting the Line Input Adaptor KS-U57 and
the external component, refer to the Installation/
Connection Manual (separate volume).

• Before operating the external component using the
following procedure, select the external input
correctly. (See “To select the external component to
use – EXT IN” on page 21.)

DAB

MO

2

Turn on the connected component
and start playing the source.

3

Adjust the volume.

4

Adjust the sound characteristics
you want. (See page 17.)

ENGLISH

1

Select the external component
(CD-CH).

• If “LINE IN”* does not appear on the display, see
page 21 and select the external input (“LINE IN”).

* Displayed only when one of the following sources is

selected — FM, AM and Tape.

Note on One-Touch Operation:

When you press CD-CH, the power automatically
comes on. You do not have to press to turn
on the power.

25

DAB TUNER OPERATIONS

MO

DISP

TP

ENGLISH

We recommend that you use DAB (Digital Audio
Broadcasting) tuner KT-DB1500 with your unit.
If you have another DAB tuner, consult your JVC
IN-CAR ENTERTAINMENT dealer.

• Refer also to the Instructions supplied with your
DAB tuner.

RDS

PTY

8 9 10 11 127

What is DAB system?

DAB is one of the digital radio broadcasting
systems available toda y . It can deliver CD quality
sound without any annoying interference and
signal distortion. Furthermore, it can carry text,
pictures and data.
In contrast to FM broadcast, where each
programme is transmitted on its own frequency,
DAB combines several programmes (called
“services”) to form one “ensemble.”
With the DAB tuner connected with this unit,
you can enjoy these DAB services.

DAB

MO

2

Select the DAB band (DAB1, DAB2,
or DAB3).

Each time you press the
button, the DAB band
changes as follows:

DAB1

Note:

This receiver has thr ee DAB bands (D AB1, DAB2,
DAB3). You can use any of them to tune into an
ensemble.

3

Start searching an ensemble.

DAB2 DAB3

Press ¢ to search
ensembles of higher
frequencies.

Tuning into an ensemble and
one of the services

A typical ensemble has 6 or more programmes
(services) broadcast at the same time. After tuning
into an ensemble, you can select a service you
want to listen to.

Before you start....

Press DAB (FM AM) briefly if tape, CD changer or
external component is the current source.

1

Select the DAB tuner.

Each time you press and
hold the button, the DAB
tuner and the FM/AM tuner
are alternately selected.

FM/AMDAB

26

Press 4 to search
ensembles of lower
frequencies.

When an ensemble is received, searching
stops.

To stop searching before an ensemble is
received, press the same button you have

pressed for searching.

4

Select a service you want to listen to.

Press RND (5) to select the
next service.

Press RPT (∞) to select the
previous service.

To change the display information while

FM/AMDAB

tuning into an ensemble

Normally service name is shown on the display.
If you want to change the displa y information, press
DISP.
Each time you press the button, the following
information appears on the display for a while.

Clock time

Service name

Ensemble name

Channel number

Frequency

Band/Preset number

Storing DAB services in
memory

You can preset up to 6 DAB services in each
DAB band (DAB1, DAB2 and DAB3) manually.

1

Select the DAB tuner.

Each time you press and
hold the button, the DAB
tuner and the FM/AM tuner
are alternately selected.

2

Select the DAB band (DAB1, DAB2
or DAB3) you want.

Each time you press the
button, the DAB band
changes as follows:

ENGLISH

To tune into a particular ensemble without
searching:

1 Press and hold DAB (FM AM) to select DAB

tuner as the source.

2 Press DAB (FM AM) repeatedly to select the

DAB band (DAB1, DAB2 or DAB3).

3 Press and hold ¢ or 4 for more

than 1 second.

4 Press ¢ or 4 repeatedly until the

ensemble you want is reached.

• If you hold down the button, the frequency
keeps changing until you release the button.

To restore the FM/AM tuner

Press and hold DAB (FM AM) again.

DAB1

3

Tune into an ensemble you want.

4

Select a service of the ensemble you

DAB2 DAB3

want.

MO

Press RND (5) to select the
next service.

Press RPT (∞) to select the
previous service.

CONTINUED ON THE NEXT PAGE

27

5

FM/AMDAB

Press and hold the number button
(in this example, 1) you want to
store the selected service into for
more than 2 seconds.

ENGLISH

Band/preset number
and service name flash
alternately for a while.

6

Repeat the above procedure to store
other DAB services into other preset
numbers.

Notes:

• A previously pr eset DAB service is er ased when a new
DAB service is stored in the same preset number.

• Preset DAB services ar e erased when the power supply
to the memory circuit is interrupted (for example,
during battery replacement). If this occurs, pr eset the
DAB services again.

Tuning into a preset DAB
service

You can easily tune into a preset DAB service.
Remember that you must store services first. If
you have not stored them yet, see page 27.

1

Select the DAB tuner.

Each time you press and
hold the button, the DAB
tuner and the FM/AM tuner
are alternately selected.

2

Select the DAB band (DAB1, DAB2
or DAB3) you want.

Each time you press the
button, the DAB band
changes as follows:

DAB1

3

Select the number (1 – 6) for the
preset DAB service you want.

DAB2 DAB3

8 9 10 11 127

28

TROUBLESHOOTING

What appears to be trouble is not always serious. Check the following points before calling a service
center.

Symptoms

Causes

Remedies

• A cassette tape cannot be
inserted.

• A cassette tape cannot be
ejected.

• Cassette tapes become hot.

• Tape sound is at very low
level and sound quality is
degraded.

• Sound is sometimes
interrupted.

• Sound cannot be heard from
the speakers.

• SSM (Strong-station
Sequential Memory)
automatic preset does not
work.

You have tried to insert a
cassette in the wrong way.

Cassette ejection is prohibited.

This is not a malfunction.
The tape head is dirty.

Connections are not good.

The volume is turned to the
minimum level.

Connections are incorrect.

Signals are too weak.

Insert the cassette with the
exposed tape facing right.

Press and hold TAPE 23 and
0 for more than two seconds.

Clean it with a head cleaning
tape.

Check the cords and
connections.

Adjust it to the optimum level.

Check the cords and
connections.

Store stations manually.

ENGLISH

• Static noise while listening to
the radio.

• “NO DISC” appears on the
display.

• “NO MAG” appears on the
display.

• “RESET 8” appears on the
display.

• “RESET 1” - “RESET 7”

appears on the display.

• This unit does not work at all.

• The CD changer does not

work at all.

The antenna is not connected
firmly.

No CD is in the magazine.
CDs are inserted incorrectly.
No magazine is loaded in the

CD changer.
This unit is not connected to a

CD changer correctly.

The built-in microcomputer may
function incorrectly due to
noise, etc.

Connect the antenna firmly.

Insert CDs into the magazine.
Insert them correctly.
Insert the magazine.

Connect this unit and the CD
changer correctly and press the
reset button of the CD changer.

Press the reset button of the
CD changer.

Press and hold both the SEL
(select) and buttons
at the same time for several
seconds. (The clock setting and
preset stations stored in
memory are erased.)
(See page 2.)

29

MAINTENANCE

This unit requires very little attention, but you will
be able to extend the life of the unit if you follow
the instructions below.

To clean the heads

ENGLISH

• Clean the heads after every 10 hours of use using
a wet-type head cleaning tape (available at an
audio store).
When the head becomes dirty, you may realize
the following symptoms:
– Sound quality is reduced.
– Sound level decreases.
– Sound drops out.

• Do not play dirty or dusty tapes.

• Do not touch the highly-polished head with any
metallic or magnetic tools.

CAUTION:

• Do not play the cassettes with peeling labels;
otherwise, they can damage the unit.

• Tighten tapes to remove slack since loose tape
may become entangled with the mechanism.

• Do not leave a cassette in the cassette
compartment after use, as the tape may become
slack.

The function below is also provided to ensure the
longer life of this unit.

Ignition key-off release/Ignition key-on
play

• Turning off the ignition key with a cassette in the
compartment automatically releases the tape
from the unit’s tapehead.

• Turning on the ignition key with a cassette in the
compartment starts playback automatically if y ou
turned off the ignition during tape play.

To keep the tape clean

• Always store the cassettes to their storage cases
after use.

• Do not store cassettes in the following places:
– Subject to direct sunlight
– With high humidity
– At extremely hot temperatures

30

SPECIFICATIONS

AUDIO AMPLIFIER SECTION

Maximum Power Output:

Front: 40 W per channel
Rear: 40 W per channel

Continuous Power Output (RMS):

Front: 16 W per channel into 4 Ω, 40 Hz

to 20 000 Hz at no more than

0.8% total harmonic distortion.

Rear: 16 W per channel into 4 Ω, 40 Hz

to 20 000 Hz at no more than

0.8% total harmonic distortion.
Load Impedance: 4 Ω (4 Ω to 8 Ω allowance)
Tone Control Range:

Bass: ±10 dB at 100 Hz

Treble: ±10 dB at 10 kHz
Frequency Response: 40 Hz to 20000 Hz
Signal-to-Noise Ratio: 70 dB
Line-Out Level/Impedance:

2.0 V/20 kΩ load (250 nWb/m)

TUNER SECTION

CASSETTE DECK SECTION

Wow & Flutter: 0.11% (WRMS)
Fast-Wind Time: 100 sec. (C-60)
Frequency Response: 30 Hz to 16 000 Hz

(Normal tape)
Signal-to-Noise Ratio: 56 dB
Stereo Separation: 40 dB

GENERAL

Power Requirement:

Operating Voltage: DC 14.4 V

(11 V to16 V allowance)
Grounding System: Negative ground
Allowable Operating Temperature: 0°C to +40°C
Dimensions (W × H × D):

Installation Size: 182 mm × 52 mm × 150 mm
Panel Size: 188 mm × 58 mm × 14 mm
Mass: 1.4 kg (excluding accessories)

ENGLISH

Frequency Range:

FM: 87.5 MHz to 108.0 MHz
AM: (MW)522 kHz to 1 620 kHz

(LW) 144 kHz to 279 kHz

[FM Tuner]

Usable Sensitivity: 11.3 dBf (1.0 µV/75 Ω)
50 dB Quieting Sensitivity:

16.3 dBf (1.8 µV/75 Ω)

Alternate Channel Selectivity (400 kHz):

65 dB
Frequency Response: 40 Hz to 15000 Hz
Stereo Separation: 30 dB
Capture Ratio: 1.5 dB

[MW Tuner]

Sensitivity: 20 µV
Selectivity: 35 dB

[LW Tuner]

Sensitivity: 50 µV

Design and specifications subject to change without
notice.

31

Having TROUBLE with operation?

Please reset your unit

Refer to page of How to reset your unit

Haben Sie PROBLEME mit dem Betrieb?

Bitte setzen Sie Ihr Gerät zurück

Siehe Seite Zurücksetzen des Geräts

Vous avez des PROBLÈMES de fonctionnement?

Réinitialisez votre appareil

Référez-vous à la page intitulée Comment réinitialiser votre appareil

Hebt u PROBLEMEN met de bediening?

Stel het apparaat terug

Zie de pagina met de paragraaf Het apparaat terugstellen

EN, GE, FR, NL

VICTOR COMPANY OF JAPAN, LIMITED

1100MNMMDWJES

JVC

184 mm

53 mm

KS-FX722R

Installation/Connection Manual
Einbau/Anschlußanleitung
Manuel d’installation/raccordement
Handleiding voor installatie/aansluiting

ENGLISH

• This unit is designed to operate on 12 V DC,

NEGATIVE ground electrical systems.

INSTALLATION
(IN-DASH MOUNTING)

• The following illustration shows a typical
installation. However, you should make
adjustments corresponding to your specific car.
If you have any questions or require inf ormation
regarding installation kits, consult your JVC IN­CAR ENTERTAINMENT dealer or a company
supplying kits.

DEUTSCH

• Dieses Gerät ist für einen Betrieb in elektrischen

Anlagen mit 12 V Gleichstrom und (–) Erdung
ausgelegt.

EINBAU
(IM ARMATURENBRETT)

• Die folgende Abbildung zeigt einen typischen

Einbau. Dennoch müssen Sie entsprechend
Ihrem jeweiligen Auto Anpassungen
vornehmen. Bei irgendwelchen Fragen oder
wenn Sie Informationen hinsichtlich des
Einbausatzes brauchen, wenden Sie sich an
ihren JVC Autoradiohändler oder ein
Unternehmen das diese Einbausätze vertreibt.

FRANÇAIS

•

Cet appareil est conçu pour fonctionner sur des
sources de courant continu de 12 V à masse
NEGATIVE.

INSTALLATION (MONTAGE
DANS LE TABLEAU DE BORD)

•

L’illustration suivante est un exemple
d’installation typique. Cependant, vous devez
faire les ajustements correspondant à votre
voiture particulière. Si vous a vez des questions
ou avez besoin d’information sur des kits
d’installation, consulter votre revendeur
d’autoradios JVC ou une compagnie
d’approvisionnement.

NEDERLANDS

• Dit apparaat mag worden gebruikt bij elektrische
systemen die werken op 12 V gelijkstroom met
negatieve aarding.

INSTALLATIE (INBOUW IN
HET DASHBOARD)

• Op de volgende afbeelding kunt u zien hoe de
installatie, normaal gesproken, in zijn werk gaat. U
moet echter bij de installatie rekening houden met
de bijzonderheden van uw eigen auto. Neem bij
vragen of voor meer bijzonderheden over
inbouwpakketten contact op met uw JVC car audio
dealer of een dealer of een bedrijf dat
inbouwpakketten levert.

1100MNMMDWJES
EN, GE, FR, NL

1

Before mounting: Press (Control
Panel Release button) to detach the control
panel if already attached.

* When shipped from the factory, the control

panel is packed in the hard case.

2

Remove the trim plate.

3

Remove the sleeve after disengaging the
sleeve locks.

1 Stand the unit.

Note: When you stand the unit, be careful
not to damage the fuse on the rear.

2 Insert the 2 handles between the unit and

the sleeve, as illustrated, to disengage the
sleeve locks.

3 Remove the sleeve.

Note: Be sure to keep the handles for
future use after installing the unit.

4

Install the sleeve into the dashboard.
* After the sleeve is correctly installed into

the dashboard, bend the appropriate tabs
to hold the sleeve firmly in place, as
illustrated.

5

Fix the mounting bolt to the rear of the unit’s
body and place the rubber cushion over the
end of the bolt.

6

Do the required electrical connections.

7

Slide the unit into the sleeve until it is locked.

8

Attach the trim plate so that the projection
on the trim plate is fixed to the left side of
the unit.

9

Attach the control panel.

1

Vor dem Einbau: Drücken Sie (Freigabe
der Bedienungsblende), um die Arretierung
der Bedienungsblende zu lösen, sofern diese
bereits angebracht ist.

* Bei der Auslieferung ab Werk ist die

Bedienungsblende im Etui verpackt.

2

Die Frontrahmen herausnehmen.

3

Die Halterung nach dem Entriegeln der
Halterungensperren abnehmen.

1 Das Gerät aufstellen.

Hinweis: Beim Aufstellen des Geräts
darauf achten, daß die Sicherung auf der
Rückseite nicht beschädigt wird.

2 Die 2 Griffe zwischen dem Gerät und der

Halterung wie abgebildet einstecken und
die Halterungensperren entriegeln.

3 Die Halterung entfernen.

Hinweis: Sicherstellen, daß die Griffe für
künftigen Gebrauch nach dem Einbau des
Geräts aufbewahrt werden.

4

Die Halterung im Armaturenbrett einbauen.
* Nach dem korrekten Einbau der Halterung

im Armaturenbrett, die entsprechenden
Riegel umknicken, um die Halterung an
ihrem Platz zu sichern, siehe Abbildung.

5

Die Befestigungsschraube an der Rückseite
des Gerätekörpers befestigen und das Ende
der Schraube mit einem Gummipuffer
abdecken.

6

Nehmen Sie die erforderlichen elektrischen
Anschlüsse vor.

7

Das Gerät in die Halterung schieben, bis es
einrastet.

8

Befestigen Sie die Frontrahmen in der Form,
daß der Fortsatz der Frontrahmen auf der
linken Seite des Geräts befestigt wird.

9

Die Schalttafel anbringen.

1

Avant le montage:

Appuyer sur
(déblocage du panneau de commande) pour
éventeullement détacher le panneau de
commande.

* Lorsque ce panneau de commande sort

d’usine, il est rangé dans un étui de transport.

2

Retirer la plaque d’assemblage.

3

Libérer les verrous du manchon et retirer le
manchon.

1

Poser l’appareil à la verticale.

Remarque:

Lorsque vous mettez l’appareil
à la verticale, faire attention de ne pas
endommager le fusible situé sur l’arrière.

2

Insérer les 2 poignées entre l’appareil et le
manchon comme indiqué pour désengagé
les verrous de manchon.

3

Retirer le manchon.

Remarque:

S’assurer de garder les
poignées pour une utilisation ultérieur,
après l’installation de l’appareil.

4

Installer le manchon dans le tableau de bord.
* Après installation correcte du manchon dans

le tableau de bord, plier les bonnes pattes
pour maintenir fermement le manchon en
place, comme montré.

5

Monter le boulon de montage sur l’arrière du
corps de l’appareil puis passer l’amortisseur
en caoutchouc sur l’extrémité du boulon.

6

Réalisez les connexions électriques.

7

Faire glisser l’appareil dans le manchon jusqu’à
ce qu’il soit verrouillé.

8

Attachez la plaque d’assemblage de façon que
la projection de la plaque d’assemblage soit
fixée sur le côté gauche de l’appareil.

9

Remonter le panneau de commande.

1

Voordat u aan de montage v an het apparaat
begint: Druk op

(het bedieningspaneel
vrijgeven) als u het bedieningspaneel wilt
loskoppelen indien dit aan de eenheid is
vastgekoppeld.

* Standaard wordt het bedieningspaneel bij het

verlaten van de fabriek los verpakt meegele verd.

2

Verwijder de sierplaat.

3

Verwijder het huis nadat u de klemmen hebt
losgemaakt.

1 Zet het apparaat rechtop.

Opmerking: W anneer u het apparaat rechtop
zet, moet u erop letten dat u de zekering aan
de achterkant niet beschadigt.

2 Plaats de 2 hendels, zoals afgebeeld, tussen het

apparaat en het huis, om de klemmen los te
maken.

3 Verwijder het huis.

Opmerking: Bewaar de hendels nadat u het
apparaat hebt geïnstalleerd, zodat u ze ook in
de toekomst kunt gebruiken.

4

Installeer het huis in het dashboard.
* Nadat het huis op de juiste wijze in het dashboard

is geplaatst, moet u de palletjes, zoals afgebeeld,
stevig op hun plaats duwen.

5

Maak de bevestigingsbout aan de achterkant van
het apparaat vast en plaats de rubberdop over het
uiteinde van de bout.

6

Breng de vereiste elektrische verbindingen tot stand.

7

Schuif het apparaat in het huis totdat het
vergrendeld is.

8

Bevestig de sierplaat zodanig dat het uitstekende
deel van de plaat aan de linkerkant van de eenheid
vast komt te zitten.

9

Bevestig het bedieningspaneel.

GET0010-003A

[E]

Control panel

Schalttefel

Panneau de commande

Bedieningspaneel

9

8

7

Sleeve

Halterung

Manchon

Huis

4

*

See “ELECTRICAL CONNECTIONS.”

Siehe „ELEKTRISCHE ANSCHLÜSSE“.

Référez-vous “RACCORDEMENTS
ELECTRIQUES” .

Zie “ELEKTRISCHE VERBINDINGEN”.

Mounting bolt

Befestigungsschraube

Boulon de montage

Bevestigingsbout

6

3

Lock Plate

Arretierplättchen

Plaque de verrouillage

Ver grendelingsplaat

Sleeve

Halterung

Manchon

Huis

Fuse

Sicherung

Fusible

Zekering

Slot

Schlitz

Fente

Sleuf

Handle

Griffe

Poignée

Hendels

1

2

Trim plate

Frontrahmen

Plaque d’assemblage

Sierplaat

Control panel

Schalttefel

Panneau de commande

Bedieningspaneel

Dashboard

Armaturenbrett

Tableau de bord

Dashboard

JVC

5

Trim plate

Frontrahmen

Plaque d’assemblage

Sierplaat

4

Rubber cushion

Gummipuffer

Amortisseur en caoutchouc

Rubberdop

• When installing the unit without using the sleeve

• Beim Einbau des Geräts ohne Halterung

• Lors de l’installation de l’appareil scans utiliser de manchon

• Wanneer u het apparaat zonder huis installeert

In a Toyota for example, first remove the car radio and install the unit in its place.

Zum Beispiel in einem Toyota zuerst das Autoradio ausbauen und dann das Gerät an seinem Platz einbauen.

Par exemple dans une Toyota, retirer d’abord l’autoradio et installer l’appareil à la place.

Voorbeeld: Bij een Toyota moet u eerst de autoradio verwijderen en daarna het apparaat installeren.

• When using the optional stay

• Beim Verwenden der Anker-Option

• Lors de l’utilisation du hauban en option

• Wanneer u de steun gebruikt (facultatief)

32

Removing the unit

• Before removing the unit, release the rear
section.

1

Remove the control panel.

2

Remove the trim plate.

3

Insert the 2 handles into the slots, as shown.
Then, while gently pulling the handles away
from each other, slide out the unit. (Be sure

to keep the handles after installing it.)

Ausbau des Geräts

• Vor dem Ausbau des Geräts den hinteren Teil
freigeben.

1

Die Schalttafel abnehmen.

2

Den Frontrahmen herausnehmen.

3

Die 2 Griffe in die Schlitze wie gezeigt stecken.
Dann die Griffe behutsam auseinander ziehen
und das Gerät herausziehen. (Die Griffe nach

dem Einbau auf jeden Fall aufbewahren.)

Retrait de l’appareil

•

Avant de retirer l’appareil, libérer la section arrière.

1

Retirer le panneau de commande.

2

Retirer la plaque d’assemblage.

3

Introduire les deux poignées dans les fentes,
comme montré. Puis, tout en tirant doucement
les poignées écartées, faire glisser l’appareil
pour le sortir.

(S’assurer de conserver les

poignées après l’installation de l’appareil.)

Verwijderen van het apparaat

• Voordat u het apparaat verwijdert, moet u het

achtergedeelte losmaken.

1

Verwijder het bedieningspaneel.

2

Verwijder de sierplaat.

3

Plaats de 2 hendels, zoals afgebeeld, in de sleuven. Daarna
duwt u de hendels zachtjes uit elkaar en kunt u het apparaat
naar buiten schuiven. (Bewaar de hendels nadat u

het apparaat hebt geïnstalleerd!)

1

Hard case/Control panel

Etui/Schalttefel

Etui de transport/Panneau de commande

Behuizing/Bedieningspaneel

RACCORDEMENTS ELECTRIQUES

Pour éviter tout court-circuit, nous vous
recommandons de débrancher la borne négative de
la batterie et d’effectuer tous les raccordements
électriques avant d’installer l’appareil. Si l’on n’est pas
sûr de pouvoir installer correctement cet appareil, le
faire installer par un technicien qualifié.

Remarque:

Cet appareil est conçu pour fonctionner sur des
sources de courant continu de

12 V à masse

NEGATIVE

. Si votre véhicule n’offre pas ce type
d’alimentation, il vous faut un convertisseur de tension,
que vous pouvez acheter chez un revendeur
d’autoradios JVC.

•

Remplacer le fusible par un de la valeur précisée.
Si le fusible saute souvent, consulter votre rev endeur
d’autoradios JVC.

•

Si le bruit est un problème...
Cet appareil incorpore un filtre de bruit dans le circuit
d’alimentation. Cependant, avec certains véhicules,
quelques claquements ou autres bruits non désirés
risquent de se produire. Si cela arrive, raccorder la

borne arrière de masse

de l’appareil au châssis
de la voiture (voir le diagramme de raccordement)
en utiliscant des cordons les plus gros et les plus
courts possibles telle qu’une barre de cuivre ou une
tresse. Si le bruit persiste, consulter votre re vendeur
d’autoradios JVC.

•

La puisscance admissible des haut-parleurs devrait
n’être pas plus qu’ c 40 W à l’arrière et 40 W à l’avant,
avec une impédance de

4 Ω à 8 Ω

.

• S’assurer de raccorder la mise à la masse de
cet appareil au châssis de la voiture.

•

Le dissipateur de chaleur devient très chaud après
usage. Faire attention de ne pas le toucher en
retirant cet appareil.

ELEKTRISCHE ANSCHLÜSSE

Zur Vermeidung von Kurzschlüssen empfehlen wir,
daß Sie den negativen Batterieanschluß abtrennen
und alle elektrischen Anschlüsse herstellen, bevor
das Gerät eingebaut wird. Sind Sie sich über den
richtigen Einbau des Geräts nicht sicher, lassen Sie
es von einem qualifizierten Techniker einbauen.

Hinweis:
Dieses Gerät ist für einen Betrieb in elektrischen
Anlagen mit 12 V Gleichstrom und (–) Erdung

ausgelegt. Verfügt Ihr Fahrzeug nicht über diese
Anlage, ist ein Spannungsinverter erforderlich, der
bei JVC Autoradiohändler erworben werden kann.

• Die Sicherung mit einer der entsprechenden
Nennleistung ersetzen. Brennt die Sicherung häufig
durch, wenden Sie sich an ihren JVC
Autoradiohändler.

• Sind Störgeräusche ein Problem...
Dieses Gerät enthält ein Störfilter im Stromkreis. Bei
manchen Fahrzeugen kann jedoch ein Klicken oder
andere unerwünschte Störgeräusche auftreten.
Sollte das der Fall sein, die hintere
Erdungscanschlußklemme (siehe Schaltplan) des
Geräts am Fahrwerk des Fahrzeugs anschließen,
dabei kürzere und dickere Kabel wie beispielsweise
Kupfergeflechtdraht oder Stahldraht verwenden.
Bleibt Störgeräusch bestehen, wenden Sie sich an
Ihren JVC Autoradiohändler.

• Maximale Eingangsleistung der Lautsprecher sollte
nicht mehr als 40 W hinten und 40 W vorne sein,
mit einer Impedanz von 4 Ω bis 8 Ω.

• Sicherstellen, daß das Gerät am Fahrwerk

geerdet wird.

• Das Abstrahlblech wird nach dem Gebrauch sehr
heiß. Beim Ausbau des Geräts darauf achten, das
Abstrahlblech nicht zu berühren.

ELEKTRISCHE VERBINDINGEN

Om kortsluiting te voorkomen adviseren wij u om de
minpool van de accu los te maken en alle elektrische
verbindingen tot stand te brengen voordat u het apparaat in
de auto installeert. Als u niet zeker weet hoe u dit apparaat
moet installeren, kunt u dit beter door een daartoe
gekwalificeerde technicus laten doen.

Opmerking:

Dit apparaat mag worden gebruikt bij elektrische systemen
die werken op 12 V gelijkstroom met negatieve
aarding. Als uw auto niet is uitgerust met een dergelijk
systeem, is een spanningsomzetter vereist. Dit instrument
kan worden aangeschaft bij JVC car audio dealers.

• Vervang de zekering door een exemplaar met het
aangegeven vermogen. Als de zekering vaak doorslaat,
moet u uw JVC car audio dealer raadplegen.

• Als u geluidsproblemen hebt…
De krachtschakeling van dit apparaat heeft een ingebouwd
geluidsfilter. In sommige voertuigen zijn tikgeluiden of
andere ongewenste geluiden te horen. Als dit gebeurt,
moet u de massaklem aan de achterkant (zie
aansluitingsschema) aan het chassis van de auto
vastmaken met behulp van een kortere en dikkere kabel,
zoals kopermanteldraad of tellerkabel. Als het geluid niet
verdwijnt, moet u contact opnemen met uw JVC car audio
dealer.

• Het maximum ingangsvermogen van de speakers moet
achterin niet meer dan 40 W zijn en voorin 40 W, met
een impedantie van 4 Ω tot 8 Ω.

• Zorg ervoor dat dit apparaat door middel van

een aardkabel is verbonden met het chassis van
de auto.

• De warmte-opnemer kan na gebruik erg heet worden.
Raak de warmte-opnemer niet aan wanneer u dit apparaat
van zijn plaats haalt.

ELECTRICAL CONNECTIONS

To prevent short circuits, we recommend that you
disconnect the battery’s negative terminal and make
all electrical connections before installing the unit. If
you are not sure how to install this unit correctly , hav e
it installed by a qualified technician.

Note:
This unit is designed to operate on 12 V DC,
NEGATIVE ground electrical systems. If your

vehicle does not have this system, a voltage in verter
is required, which can be purchased at JVC IN-CAR
ENTERTAINMENT dealers.

• Replace the fuse with one of the specified rating. If
the fuse blows frequently , consult your JVC IN-CAR
ENTERTAINMENT dealer.

• If noise is a problem...
This unit incorporates a noise filter in the power
circuit. Howe ver, with some v ehicles, clicking or other
unwanted noise may occur. If this happens, connect
the unit’s rear ground terminal (see connection
diagram) to the car’s chassis using shorter and
thicker cords, such as copper braiding or gauge wire.
If noise still persists, consult your JVC IN-CAR
ENTERTAINMENT dealer.

• Maximum input of the speakers should be no more
than 40 W at the rear and 40 W at the front, with an
impedance of 4 Ω to 8 Ω.

• Be sure to ground this unit to the car’s chassis.

• The heat sink becomes very hot after use. Be careful
not to touch it when removing this unit.

Teileliste für den Einbau und Anschluß

Die folgenden Teile werden zusammen mit diesem
Gerät geliefert.
Nach ihrer Überprüfung, die Teile richtig einsetzen.

Liste des pièces pour l’installation et
raccordement

Les pièces suivantes sont fournies avec cet appareil.
Après vérification, veuillez les placer correctement.

Lijst van onderdelen die u bij
installatie en aansluiting nodig hebt

De volgende onderdelen worden bij het apparaat geleverd.
Installeer ze op de juiste wijze, nadat u ze hebt gecontroleerd.

Parts list for installation and connection

The following parts are provided with this unit.
After checking them, please set them correctly.

Control panel

Schalttefel

Panneau de commande

Bedieningspaneel

Trim plate

Frontrahmen

Plaque d’assemblage

Sierplaat

Note: When installing the unit on the mounting bracket, make sure to use the 6 mm-long screws. If longer screws are
used, they could damage the unit.

Hinweis: Beim Anbringen des Gerät an der Konsole sicherstellen, daß 6 mm lange Schrauben verwendet werden.
Werden längere Schrauben verwendet, können sie das Gerät beschädigen.

Remarque:

Lors de l’installation de l’appareil sur le support de montage, s’assurer d’utiliser des vis d’une longueur de

6 mm. Si des vis plus longues sont utilisées, elles peuvent endommager l’appareil.

Opmerking: W anneer u het apparaat aan de be v estigingsklem v astmaakt, moet u de 6 mm lange schroe v en gebruik en. Als u langere
schroeven gebruikt, kan het apparaat worden beschadigd.

Handle

Griff

Poignée

Hendel

Dashboard

Armaturenbrett

Tableau de bord

Dashboard

Fire wall

Feuerwand

Cloison

Brandscherm

Sleeve

Halterung

Manchon

Huis

Lock nut

Sicherungsmutter

Ecrou d’arrêt

Contra-moer

Stay (option)

Anker (Option)

Hauban (en option)

Steun (facultatief)

Screw (option)

Schraube (Option)

Vis (en option)

Schroef (facultatief)

Bracket*

Konsole*

Support*

Console*

Bracket*

Konsole*

Support*

Console*

Flat type screws (M5 x 6 mm)*

Senkkopfschrauben (M5 x 6 mm)*

Vis à tête plate (M5 x 6 mm)*

Platkopschroeven (M5 x 6 mm)*

Pocket

Taschen

Poche

Zak

* Not included with this unit.

* Nicht Teil dieses Geräts.

*

Non fourni avec cet appareil.

* Niet meegeleverd.

Flat type screws (M5 x 6 mm)*

Senkkopfschrauben (M5 x 6 mm)*

Vis à tête plate (M5 x 6 mm)*

Platkopschroeven (M5 x 6 mm)*

Mounting bolt (M5 x 20 mm)

Befestigungsschraube (M5 x 20 mm)

Boulon de montage (M5 x 20 mm)

Bevestigingsbout (M5 x 20 mm)

Lock nut (M5)

Sicherungsmutter (M5)

Ecrou d’arrêt (M5)

Contra-moer (M5)

Washer (ø5)

Unterlegscheibe(ø5)

Rondelle (ø5)

Sluitring (ø5)

Handles

Griffe

Poignées

Hendels

Power cord

Stromkable

Cordon d’alimentation

Stroomkabel

Heat sink

Abstrahlblech

Dissipateur de chaleur

Warmte-opnemer

Mounting bolt

Befestigungsschraube

Boulon de montage

Bevestigingsbout

Washer

Unterlegscheibe

Rondelle

Sluitring

Rubber cushion

Gummipuffer

Amortisseur en caoutchouc

Rubberdop

Trim plate

Frontrahmen

Plaque d’assemblage

Sierplaat

Sleeve

Halterung

Manchon

Huis

B110B3 B5 B7
B2 B4 B6 B8

A5 A7

A2 A4 A8

2

3

1

4

5

1

2

3

6

A8

A4

A7

A5

A2

B6 B5 B4 B3 B8 B7 B2 B1

B1 B3 B5 B7
B2 B4 B6 B8

A5 A7

A2 A4 A6 A8

A6

FRANÇAIS

DEUTSCH

NEDERLANDS

ENGLISH

A Typical Connections / Typische Anschlüsse / Raccordements typiques / Normale verbindingen

Before connecting: Check the wiring in the vehicle
carefully. Incorrect connection may cause serious
damage to this unit.

1

Connect the colored leads of the power cord to the
car battery, speakers and power aerial (if any) in the
following sequence.

1 Black: ground
2 Yellow: to car battery (constant 12 V)
3 Red: to an accessory terminal
4 Blue with white stripe: to power aerial

(200 mA max.)

5 Brown: to cellular phone system (For details,

refer to the instructions of the cellular phone.)

6 Others: to speakers

2

Connect the aerial cord.

3

Finally connect the wiring harness to the unit.

Note: If your vehicle does not have any accessory
terminal, move the fuse from the fuse position 1 (initial
position) to fuse position 2, and connect the red lead
(A7) to the positive (+) battery terminal.

• The yellow lead (A4) is not used in this case.

Vor dem Anschließen: Die Verdrahtung im Fahrzeug
sorgfältig überprüfen. Falsche Anschlüsse können
ernsthafte Schäden am Gerät hervorrufen.

1

Die farbigen Leitungen des
Spannunsgversorgungskabels an der
Autobatterie, den Lautsprechern und dem
Motorantenne (sofern vorhanden) in folgender
Reihenfolge anschließen.

1 Schwarz: Erdung
2 Gelb: an Autobatterie (konstant 12 V)
3 Rot: an Zubehöranschlußklemme
4 Blau mit weißem Streifen: an Motorantenne

(max. 200 mA)

5 Braun: an Mobiltelefon (Weitere informationen

entnehmen Sie bitte der Bedienungscanleitung
des Mobiltelefons.)

6 Andere: an Lautsprecher

2

Das Antennenkabel anschließen.

3

Die Kabelbäume am Gerät anschließen.

Hinweis: Verfügt Ihr Fahrzeug nicht über eine
Zubehöranschlußklemme, die Sicherung von der 1.
Sicherungsposition (Erstposition) in die 2.
Sicherungsposition versetzen, die rote Leitung (A7)
an der (+) Batterieanschlußklemme anschließen.

• Die gelbe Leitung (A4) wird in diesem Fall nicht
verwendet.

Avant de commencer la connexion:

vérifiez
attentivement le câblage du véhicule. Une connexion
incorrecte peut endommager sérieusement l’appareil.

1

Connectez les fils de couleur du cordon d’alimentation
à la batterie de la voiture, aux enceintes et à l’antenne
automatique (s’il y en a une) dans l’ordre suivant.

1

Noir: a la masse

2

Jaune: a la batterie de la voiture (12 V constant)

3

Rouge: à la prise accessoire

4

Bleu avec bande blanche: à l’antenne automatique
(200 mA max.)

5

Marron: à un système de téléphone cellulaire
(Pour les détails, se référer aux instructions du
téléphone cellulaire.)

6

Autres: aux enceintes

2

Connectez le cordon d’antenne.

3

Finalement, connectez le faisceau de fils à l’appareil.

Remarque:

Si votre véhicule ne possède pas de borne
accessoire, déplacez le fusible de la position de fusible
1 (position originale) à la position de fusible 2 et
connectez le fil rouge (A7) à la borne positive (+) de la
batterie.

• Le fil jaune (A4) n’est pas utilisé dans ce cas.

Alvorens de verbindingen tot stand te brengen:

moet u de bedrading in de auto zorgvuldig. Het apparaat kan
door verkeerde verbindingen ernstige schade oplopen.

1

Sluit de gekleurde snoerdraden van de stroomkable in
de hierna genoemde volgorde aan op de accu van de
auto, de luidsprekers en de antenne (indien aanwezig).

1 Zwart: aarde
2 Geel: naar de accu van de auto (constant 12 V)
3 Rood: naar de aansluitklem van de accessoire
4 Blauw met witte streep: naar de antenne

(Max. 200 mA)

5 Bruin: Naar het mobiele-telefoonsysteem (Lees

voor meer informatie de instructies die bij de
mobiele telefoon worden geleverd.)

6 Andere: naar de speakers

2

Sluit de antenne aan.

3

Verbind de draadbundel daarna met het apparaat.

Opmerking: Als uw voertuig niet beschikt over een
aansluitklem, moet u de zekering verplaatsen van stand 1
(beginstand) naar stand 2 en moet u de rode draad (A7) met
de pluspool (+) van de accu verbinden.

• In dit geval wordt de gele draad (A4) niet gebruikt.

Fig. 3Fig. 2Fig. 1

PRECAUTIONS on power supply and
speaker connections:

• DO NOT connect the speaker leads of the power

cord to the car battery; otherwise, the unit will be
seriously damaged.

• Connect the black lead (ground), yellow lead (to car
battery, constant 12 V), and red lead (to an accessory
terminal) correctly.

• BEFORE connecting the speaker leads of the power cord
to the speakers, check the speaker wiring in your car .
– If the speaker wiring in your car is as illustrated

in Fig. 1 and Fig. 2 below , DO NO T connect the unit
using that original speaker wiring. If you do, the unit
will be seriously damaged.
Redo the speaker wiring so that you can connect the
unit to the speakers as illustrated in Fig. 3.

– If the speaker wiring in your car is as illustrated

in Fig. 3, you can connect the unit using the original
speaker wiring in your car.

– If you are not sure of the speaker wiring of your car,

consult your car dealer.

VORSICHTSMASSREGELN beim
Anschließen der Stromversorgung
und Lautsprecher:

• Die Lautsprecherleitungen des Netzkabels NICHT
an der Autobatterie anschließen, da sonst das
Gerät schwer beschädigt wird.

• Die schwarze Leitung (Erdung), die gelbe Leitung (zur
Autobatterie, konstant 12 V) und die rote Leitung (zur
Zubehöranschlußklemme) richtig anschließen.

• VOR dem Anschließen der Lautsprecherleitungen des
Spannunsgversorgungskabels an die Lautsprecher, die
Lautsprecherverdrahtung in Ihrem Auto überprüfen.
– Ist die Lautsprecherverdrahtung wie unten in

“Fig. 1” und “Fig. 2” abgebildet, das Gerät
NICHT mit der Originalverdrahtung der
Lautsprecher anschließen, da sonst das Gerät
schwer beschädigt wird.
Die Lautsprecherverdrahtung erneuern, so daß Sie
das Gerät an den Lautsprechern wie in “Fig. 3”
abgebildet anschließen können.

– Ist die Lautsprecherverdrahtung in Ihrem Auto

wie in “Fig. 3” abgebildet, können Sie das Gerät
mit der Originalverdrahtung der Lautsprecher in
Ihrem Auto anschließen.

– Sind Sie sich über die Lautsprecherverdrahtung in

Ihrem Auto nicht sicher, wenden Sie sich an Ihren
Autohändler.

PRECAUTIONS sur l’alimentation et
la connexion des enceintes:

• NE CONNECTEZ PAS les fils d’enceintes du

cordon d’alimentation à la batterie; sinon,
l’appareil serait sérieusement endommagé.

•

Connectez correctement le fil noir (a la masse), le fil
jaune (a la batterie de la voiture,12 V constant) et le
fil rouge (à la prise accessoire).

•

AVANT de connecter les fils d’enceintes du cordon
d’alimentation aux enceintes, vérifiez le câblage des
enceintes de votre voiture.
–

Si le câblage des enceintes de votre voiture est
réalisé comme montré sur la Fig. 1 ou Fig. 2 ci­dessous,

NE CONNECTEZ PAS l’appareil en
utiliscant ce câblage original d’enceintes. Si vous
le faites, l’appareil sera sérieusement endommagé.
Recommencez le câblage des enceintes de façon
que vous puissiez connecter l’appareil aux
enceintes comme montré sur la Fig. 3.

–

Si le câblage des enceintes de votre voiture est
comme montré sur la Fig. 3,

vous pouvez
connecter l’appareil en utiliscant ce câblage original
d’enceintes pour votre voiture.

– Si vous n’êtes pas sûrs du câblage d’enceintes de

votre voiture, consulter le concessionnaire de votre
voiture.

VOORZORGSMAATREGELEN bij het
verbinden van de
stroomkabeldraad met de speakers:

• Verbind de speakerdraden van de stroomkabel

NIET met de accu van de auto; als u dit wel doet,
zal het apparaat ernstige schade oplopen.

• Sluit de zwarte draad (aarde), de gele draad (naar de accu

van de auto, constant 12 V) en de rode draad (naar de

aansluitklem van de accessoire

) op de juiste wijze aan.

• VOORDAT u de speakerdraden van de stroomkabel met
de speakers verbindt, moet u de bedrading van de speakers
in uw auto controleren.
– Als de bedrading van de speakers eruitziet zoals

hieronder staat afgebeeld in Fig. 1 en Fig. 2, mag
het apparaat NIET worden aangesloten met behulp van
deze oorspronkelijke speakerbedrading. Als u dat wel
doet, zal het apparaat ernstige schade oplopen.
Pas de bedrading van de speakers aan, zodat u het
apparaat met de speakers kunt verbinden, zoals staat
afgebeeld in Fig. 3.

– Als de bedrading van de speakers eruitziet zoals

staat afgebeeld in Fig. 3, kunt u het apparaat
aansluiten met behulp van de oorspronkelijke
speakerbedrading in uw auto.

– Als u twijfels hebt over de speakerbedrading in uw auto,

moet u contact opnemen met uw autodealer.

To power aerial if any

Zur Motorantenne, sofern vorhanden

Vers l’antenne automatique s’il y en a une

Naar de antenne (indien aanwezig)

Fuse position 2

2. Sicherungsposition

Position de fusible 2

Zekering, stand 2

Fuse position 1

1. Sicherungsposition

Position de fusible 1

Zekering, stand 1

To a liv e terminal in the fuse bloc k connecting to the car battery (bypassing
the ignition swich)

Zur einer stromführenden Anschlußklemme im Sicherungsblock zum
Anschließen an die Autobatterie (Umgehen des Zündschalters)

A une borne sous tension du porte-fusible connectée à la batterie de la
voiture (en dérivant l’interrupteur d’allumage)

Naar een onder spanning staande aansluitklem in het zekeringblok die is aangesloten
op de accu van de auto (u passeert de ontstekingsschakelaar)

Not included with this unit.

Wird nicht mit Gerät mitgeliefert.

Non fourni avec cet appareil.

Niet bij het apparaat inbegrepen.

*

*

*

Gray with black stripe

Grau mit schwarzem Streifen

Gris avec bande noire

Grijs met zwarte streep

White with black stripe

Weiß mit schwarzem
Streifen

Blanc avec bande noire

Wit met zwarte streep

White

Weiß

Blanc

Wit

Gray

Grau

Gris

Grijs

Green with black stripe

Grün mit schwarzem Streifen

Vert avec bande noire

Groen met zwarte streep

Green

Grün

Vert

Groen

Purple with black stripe

Lila mit schwarzem Streifen

Violet avec bande noire

Paars met zwarte streep

Purple

Lila

Violet

Paars

Left speaker (rear)

Linker Lautsprecher (hinten)

Enceinte gauche (arrière)

Linkerspeaker (achterin)

Right speaker (front)

Rechter Lautsprecher (vorne)

Enceinte droit (avant)

Rechterspeaker (voorin)

*1: Before checking the operation of this unit prior to

installation, this lead must be connected, otherwise
power cannot be turned on.

*1: Vor der Überprüfung der Funktionsfähigkeit des Geräts

vor dem Einbau, muß diese Leitung angeschlossen
werden, da sonst die Stromversorgung nicht
eingeschaltet werden kann.

*1:Pour vérifier le fonctionnement de cet appareil avant

installation, ce fil doit être raccordé, sinon l’appareil
ne peut pas être mis sous tension.

*1: Voordat u controleert of het apparaat werkt (alvorens het te

installeren), moet deze draad aangesloten zijn. Als dit niet
het geval is, kan de stroom niet worden ingeschakeld.

When connecting a CD changer, we recommend to use one of the CH-X series CD changers.

• If your CD changer is one of the KD-MK series, you need an optional cord (KS-U15K).
You can also use an external component such as a portable MD player by connecting the Line Input Adaptor KS-U57 (not supplied).
(See diagram B .)

Wenn Sie einen CD-Wechsler anschließen möchten, empfiehlt es sich, einen CD-Wechsler der Modellreihe CH-X zu verwenden.

• Wenn Ihr CD-Wechsler zur Modellreihe KD-MK gehören, benötigen Sie ein anderes Kabel (KS-U15K).
Sie können auch eine externe Komponente, z.B. einen tragbaren MD-Spieler, verwenden, wenn Sie den (nicht zum Lieferumfang
gehörenden) Line-Eingangsadapter KS-U57 anschließen (siehe Schaltplan B ).

Lors de la connexion d’un changeur CD, nous vous recommandons d’utiliser un des changeurs CD de la série CH-X.

• Si votre changeur appartient à la série KD-MK, vous avez besoin d’un cordon optionnel (KS-U15K).
Vous pouvez aussi utiliser un appareil extérieur tel qu’un lecteur de MD en connectant l’adaptateur d’entrée de ligne KS-U57 (non
fourni) (voir le diagramme B ).

Voor het aansluiten van een CD-wisselaar raden we een wisselaar uit de CH-X-serie aan.

• Als de CD-wisselaar die u wilt aansluiten uit de KD-MK-serie komt, hebt u een extra kabel nodig (KS-U15K).
Het is ook mogelijk een extern apparaat zoals een draagbare MD-speler aan te sluiten met behulp van de Line Input Adapter KS-U57 (niet meegele verd).
(Zie schema B .)

To an accessory terminal in the fuse block

Zur einer Zubehöranschlußklemme im Sicherungsblock

Vers borne accessoire du porte-fusible

Naar een aansluitklem in het zekeringblok

To metallic body or chassis of the car

Zur metallenen Karosserie oder zum Fahrwerk des Autos

Vers corps métallique ou châssis de la voiture

Naar metalen ondergrond of chassis van de auto

Ignition switch

Zündschalter

Interrupteur d’allumage

Contactschakelaar

Fuse block

Sicherungsblock

Porte-fusible

Zekeringblok

L

R

+

-

+

-

+

-

+

-

L

R

+

-

+

-

+

-

+

-

Rear ground terminal

Hintere
Erdungscanschlußklemme

Borne arrière de masse

Massaklem aan de achterkant

To aerial

Zur Antenne

A l’antenne

Naar de antenne

Line out
(see diagram B )

Schutz kappen
Signalausgang
(siehe Schaltplan B )

Sortie de ligne
(voir le diagramme B )

Uitgang
(zie schema B )

Left speaker (front)

Linker Lautsprecher (vorne)

Enceinte gauche (avant)

Linkerspeaker (voorin)

Right speaker (rear)

Rechter Lautsprecher
(hinten)

Enceinte droit (arrière)

Rechterspeaker (achterin)

Aerial terminal

Antennenanschlußklemme

Borne de l’antenne

Aansluitpunt antenne

10 A fuse

10 A Sicherung

Fusible 10 A

Zekering 10 A

Black

Schwarz

Noir

Zwart

Yellow*

1

Gelb*

1

Jaune*

1

Geel *

1

Red

Rot

Rouge

Rood

Blue with white stripe

Blau mit weißem Streifen

Bleu avec bande blanche

Blauw met witte streep

Brown / Braun /

Marron /

Bruin

To cellular phone system

Zur Moblitelephon

À un système de téléphone cellulaire

Naar het mobiele-telefoonsysteem

JVC CD changer / DAB tuner or
another external component

CD-Wechsler von JVC / DAB-Tuner
oder eine andere externe
Komponente

Changeur CD JVC /
Tuner DAB ou autre
appareil extérieur

JVC CD-wisselaar /
DAB-tuner of een ander
extern apparaat

INPUT

R

L

R

L

LINE OUT

REAR

L
R

L
R

L
R

FRONT

R

L

R

L

INPUT

Connecting the leads / Anschließen der Leitungen / Raccordement des fils / Aansluiting van de gekleurde draden

Twist the core wires when connecting.

Die Kerndrähte beim Anschließen
verdrehen.

Torsader les âmes des fils en les
raccordant.

Draai de kerndraden om elkaar heen wanneer
u ze wilt aansluiten.

Solder the core wires to connect them securely.

Die Kerndrähte anlöten, um sie fest
anzuschließen.

Souder les âmes des fils pour les raccorder
entre eux de façon sûre.

Soldeer de kerndraden zodat ze stevig vast zitten.

CAUTION / VORSICHT / PRECAUTION / LET OP!:

• To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape.

• Zur Vermeidung eines Kurzschlusses die Anschlußklemmen der NICHT
VERWENDETEN Leitungen mit Isolierklebeband umwickeln.

• Pour éviter les court-circuits, couvrir les bornes des fils qui ne sont PAS utilisés
avec de la bande isolante.

• Om kortsluiting te voorkomen, moet u de aansluitklemmen van ONGEBRUIKTE
gekleurde draden met isolatieband bedekken.

B Connections Adding Other Equipment / Anschlüsse zum Hinzufügen von anderer Ausrüstung / Raccordement pour ajouter d’autres appareils /

Aansluitingen voor het toevoegen van andere apparatuur

Amplifier / Verstärker / Amplificateur / Versterker

You can connect an amplifier and other
equipment to upgrade your car stereo system.

• Connect the remote lead (blue with white
stripe) to the remote lead of the other
equipment so that it can be controlled through
this unit.

• For amplifier only:
– Connect this unit’s line-out terminals to the

amplifier’s line-in terminals.

– Disconnect the speakers from this unit,

connect them to the amplifier. Lea ve the
speaker leads of this unit unused. (Cover
the terminals of these unused leads with
insulating tape, as illustrated above.)

Sie können einen Verstärker oder ein anderes Gerät
anschließen, um Ihre Autostereoanlage zu erweitern.

• Schließen Sie das Fernbedienungskabel (blau mit

weißem Streifen) an das Fernbedienungskabel
des anderen Geräts an, so daß es über dieses
Gerät gesteuert werden kann.

• Nur für den Verstärker:

– Die Anschlußklemmen am Ausgang dieses

Gerät an den Anschlußklemmen des
Eingangs des Verstärkers anschließen.

– Die Lautsprecher von diesem Gerät

abtrennen und am V erstärker anschließen.
Die Lautsprecherleitungen dieses Geräts
unbenutzt lassen. (Die Anschlußklemmen
dieser nicht verwendeten Leitungen mit
Isolierklebeband umwickeln, siehe
Abbidung oben.)

Vous pouvez connecter un amplificateur ou autre
appareil pour améliorer votre système autoradio.

•

Connectez le fil de commande à distance (bleu
avec bande blanche) au fil de commande à
distance de l’autre appareil de façon qu’il puisse
être commandé via cet appareil.

•

Pour l’amplificateur seulement:
– Raccorder les bornes de sortie ligne de cet

appareil aux bornes d’entrée ligne de
l’amplificateur.

– Déconnectez les enceintes de cet appareil

et connectez-les à l’amplificateur. Laissez
les fils d’enceintes de cet appareil
inutilisés. (Recouvrir les extrémités de ces
fils inutilisés avec de la bande isolante
comme montré ci-dessus.)

Het is mogelijk om uw autostereosysteem uit te
breiden met een versterker of andere apparatuur.

• Verbind de externe kabel (blauw met witte streep)
met de externe kabel van het andere apparatuur
zodat deze op afstand vanaf deze apparaat kan
worden bediend.

• Alleen voor een versterker:
– Verbind de uitgang van het apparaat met de

ingang van de versterker.

– Koppel de speakers van dit apparaat los

en verbind ze aan de versterker. Gebruik
de speakerdraden van dit apparaat niet.
(Plak de aansluitklemmen van deze
speakerdraden met isolatieband af zoals
hierboven is afgebeeld.)

To power aerial if any

Zur Motorantenne, sofern vorhanden

Vers l’antenne automatique, s’il y en a une

Naar de antenne (indien aanwezig)

Rear speakers

Hintere Lautsprecher

Enceintes arrière

Achterspeakers

Signal cord (not supplied with this unit)

Einzelleitung (nicht mit diesem Gerät mitgeliefert)

Cordon de signal (non fourni avec cet appareil)

Signaalkabel (niet meegeleverd)

Front speakers

Vordere Lautsprecher

Enceintes av a n t

V oorspeakers

Sie können einen anderen
Leistungsverstärker für die vorderen
Lautsprecher anschließen.

You can connect another
power amplifier for front
speakers.

Vous pouvez connecter un autre
amplificateur de puissance pour
les enceintes avant.

U kunt nog een
eindversterker voor de
voorspeakers aansluiten.

CD changer and DAB tuner / CD-Wechsler und DAB-Tuner / Changeur CD et tuner DAB / CD-wisselaar en DAB-tuner

You can connect a JVC CD changer and/or a
JVC DAB (Digital Audio Broadcasting) tuner.

• For their connections, refer to the instructions
supplied with them.

Sie können einen CD-Wechsler und/oder einen
DAB-Tuner (Tuner für digitalen Rundfunk) von
JVC anschließen.

• Weitere Informationen über den Anschluß

können Sie der Bedienungscanleitung
entnehmen, die dem jeweiligen Gerät beiliegt.

Vous pouvez connecter un changeur CD JVC et/
ou un tuner DAB (Digital Audio Broadcast) JVC.

•

Pour leurs connexions , référez-vous aux modes
d’emploi qui les accompagnent.

Het is mogelijk een JVC CD-wisselaar en/of JVC DAB­tuner (Digital Audio Broadcasting) aan te sluiten.

• Zie de instructies van deze apparaten voor meer
informatie over het tot stand brengen van deze
aansluiting.

Connecting cord supplied with your CD changer

Verbindungskabel, das zum Lieferumfang des CD­Wechsler gehört

Cordon de connexion fourni avec votre changeur CD

Verbindingskabel die met de CD-wisselaar w ordt meegeleverd

Connecting cord supplied with your DAB tuner

Verbindungskabel, das zum Lieferumfang des DAB­Tuners gehört

Cordon de connexion fourni avec votre tuner DAB

Verbindingskabel die met de D AB-tuner wordt meegele verd

• You can connect both components in series as illustrated above.

• Es ist möglich, beide Komponenten in einer Serienschaltung entsprechend der obigen

Darstellung anzuschließen.

•

Vous pouvez connecter les deux appareils en série comme montré ci-dessus.

• Beide apparaten zijn volgens bovenstaande illustratie in serie aan te sluiten.

External component / Externe Komponente / Appareil extérieur / Extern apparaat

Signal cord (not supplied with this unit)

Einzelleitung (nicht mit diesem Gerät mitgeliefert)

Cordon de signal (non fourni avec cet appareil)

Signaalkabel (niet meegeleverd)

Line Input Adaptor KS-U57 (not supplied with this unit)

Line-Eingangsadapter KS-U57 (nicht mit diesem Gerät mitgeliefert)

Adaptateur d’entrée de ligne KS-U57 (non fourni avec cet appareil)

Line Input Adapter KS-U57 (niet meegeleverd)

CD changer jack

Buchse für CD-Wechsler

Prise du changeur CD

Aansluiting voor CD-wisselaar

External component

Externe Komponente

Appareil extérieur

Extern apparaat

JVC DAB tuner

DAB-Tuner von JVC

Tuner DAB JVC

JVC DAB-tuner

CAUTION / VORSICHT / PRECAUTION / LET OP!:

• Before connecting the CD changer and/or the DAB tuner, make sure that the unit is
turned off.

• Bevor Sie den CD-Wechsler und/oder den DAB-Tuner anschließen, vergewissern Sie
sich, daß das Gerät ausgeschaltet ist.

• Avant de connecter le changeur CD et/ou le tuner DAB, s’assurer que l’unité est éteinte.

• Zorg ervoor dat de apparat is uitgeschakeld alvorens u de en/of DAB-tuner CD­wisselaar aansluit.

Remote lead (Blue with white stripe)

Fernbedienungsleitung (Blau mit weißem Streifen)

Fil d’alimentation à distance (Bleu avec bande blanche)

Antennedraad (Blauw met witte streep)

Remote lead

Fernbedienungsleitung

Fil d’alimentation à distance

Antennedraad

JVC Amplifier

JVC Verstärker

JVC Amplificateur

JVC Versterker

JVC Amplifier

JVC Verstärker

JVC Amplificateur

JVC Versterker

Front speakers

Vordere Lautsprecher

Enceintes av a n t

Voorspeak ers

Y-connector (not supplied with this unit)

Y-Anschluß (nicht mit diesem Gerät mitgeliefert)

Connecteur Y (non fourni avec cet appareil)

Y-connector (niet meegeleverd)

KS-FX722R

KS-FX722R

JVC DAB tuner

DAB-Tuner von JVC

Tuner DAB JVC

JVC DAB-tuner

JVC CD changer

CD-Wechsler von JVC

Changeur CD JVC

JVC CD-wisselaar

KS-FX722R

Connecting cord supplied with your DAB tuner or CD changer

Verbindungskabel, das zum Lieferumfang des DAB-Tuners oder CD-Wechslers gehört

Cordon de connexion fourni avec votre tuner DAB ou changeur CD

Verbindingskabel die met de DAB-tuner of CD-wisselaar wordt meegeleverd

JVC CD changer

CD-Wechsler von JVC

Changeur CD JVC

JVC CD-wisselaar

or

oder

ou

of

KS-FX722R

RLR

L

LINE OUT

REAR

L
R

L

R

L

R

L

R

FRONT

TROUBLESHOOTING

• The fuse blows.
* Are the red and black leads connected correctly?

• Power cannot be turned on.
* Is the yellow lead connected?

• No sound from the speakers.
* Is the speaker output lead short-circuited?

• Sound is distorted.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded

in common?

• Unit becomes hot.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded

in common?

FEHLERSUCHE

• Die Sicherung brennt durch.

* Sind die roten und schwarzen Leitungen richtig

angeschlossen?

• Stromversorgung kann nicht eingeschaltet werden.

* Ist die gelbe Leitung angeschlossen?

• Kein Ton aus den Lautsprechern.

* Ist die Lautsprecherausgangsleitung kurzgeschlossen?

• Ton verzerrt.

* Ist die Lautsprecherausgangsleitung geerdet?
* Sind die (–) Anschlußklemmen der linken und rechten

Lautsprecher zusammen geerdet?

• Gerät wird heiß.

* Ist die Lautsprecherausgangsleitung geerdet?
* Sind die (–) Anschlußklemmen der linken und rechten

Lautsprecher zusammen geerdet?

EN CAS DE DIFFICULTÉS

• Le fusible saute.

*

Les fils rouge et noir sont-ils racordés correctement?

• L’appareil ne peut pas être mise sous tension.

*

Le fil jaune est-elle raccordée?

• Pas de son des enceintes.

*

Le fil de sortie d’enceinte est-il court-circuité?

• Le son est déformé.

*

Le fil de sortie d’enceinte est-il à la masse?

*

Les bornes “–” des enceintes gauche et droit sont­elles mises ensemble à la masse?

• L’appareil devient chaud.

*

Le fil de sortie d’enceinte est-il à la masse?

*

Les bornes “–” des enceintes gauche et droit sont­elles mises ensemble à la masse?

PROBLEMEN OPLOSSEN

• De zekering slaat door.
* Zijn de rode en de zwarte draden op de juiste manier

aangesloten?

• De stroom kan niet worden ingeschakeld.
* Is de gele draad aangesloten?

• Er komt geen geluid uit de speakers.
* Is de uitgaande speakerdraad kortgesloten?

• Het geluid wordt vervormd.
* Is de uitgaande speakerdraad geaard?
* Zijn de minpolen van de linker- en de rechterspeakers

gemeenschappelijk geaard?

• Het apparaat raakt verhit.
* Is de uitgaande speakerdraad geaard?
* Zijn de minpolen van de linker- en de rechterspeakers

gemeenschappelijk geaard?