VIDEO INPUT CARD
BEDIENUNGSANLEITUNG: VIDEO-EINGANGSKARTE
MANUEL D’INSTRUCTIONS:
ISTRUZIONI: SCHEDA DI INGRESSO VIDEO
MANUAL DE INSTRUCCIONES:TARJETA DE ENTRADA VIDEO COMPUESTO
CARTE D’ENTRÉE VIDÉO
ENGLISH
DEUTSCH
FRANÇAIS
IF-CF01PNG
МОДУЛЬ VIDEO ВХОДОВ
ITALIANO
INSTRUCTIONS
ESPAÑOL
LCT2108-001A
VIDEO INPUT CARD
ENGLISH
IF-CF01PNG
INSTRUCTIONS
1
Thank you for purchasing this JVC Input Card. In order to take full advantage of the
card’s capabilities, please read and follow all instructions carefully before installing
and using the card. Retain this booklet for future reference.
Precautions
Before installing this Input Card in your monitor, please read the Safety
Precautions included in your monitor’s user manual.
FCC NOTICE (U.S.A. only)
CAUTION: Changes or modifications not approved by JVC could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
EUROPE EMC STANDARD NOTICE (Europe only)
Warning: This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measure.
EMC Supplement (Europe only)
This equipment is in conformity with the provisions and protection requirements of the
corresponding European Directives. This equipment is designed for professional video appliances
and can be used in the following environments:
• Controlled EMC environment (for example purpose built broadcasting or recording studio), and
the rural outdoors environment (far away from railways, transmitters, overhead power lines, etc.)
These input cards are only for use with specific monitors.
Consult your dealer for the compatible monitors.
2
Information for Users on Disposal of Old Equipment
[European Union]
This symbol indicates that the electrical and electronic equipment should not be
disposed as general household waste at its end-of-life. Instead, the product should
be handed over to the applicable collection point for the recycling of electrical and
electronic equipment for proper treatment, recovery and recycling in accordance
Attention:
This symbol is
only valid in the
European
Union.
with your national legislation.
By disposing of this product correctly, you will help to conserve natural resources
and will help prevent potential negative effects on the environment and human
health which could otherwise be caused by inappropriate waste handling of this
product. For more information about collection point and recycling of this product,
please contact your local municipal office, your household waste disposal service
or the shop where you purchased the product.
Penalties may be applicable for incorrect disposal of this waste, in accordance with
national legislation.
(Business users)
If you wish to dispose of this product, please visit our web page
www.jvc-europe.com to obtain information about the take-back of the product.
[Other Countries outside the European Union]
If you wish to dispose of this product, please do so in accordance with applicable
national legislation or other rules in your country for the treatment of old electrical
and electronic equipment.
ENGLISH
3
Before Installation
7 Accessaries
• Label (x 1): For placing to the rear panel and the remote control of the monitor after installing
• Slot cover (x 1): For covering the blank slot.
the Input Card.
7 Preparation
•Wear gloves to protect your hands from metal parts on the Input Card’s board.
•You will need a 6 mm Phillips screwdriver.
•Turn off the monitor’s main power and unplug the power cable from the AC outlet.
• Place the monitor with its LCD panel side down on a soft cloth so as not to damage the LCD panel.
7 Cautions
• Do not touch the terminals or board pattern of the Input Card to keep it from being damaged by
static electricity.
• Do not damage the Input Card’s connection terminal.
• Do not put anything into the Input Card’s holes or intakes.
• Do not force the Input Card into the monitor’s slot.
• Attach the slot cover on the monitor’s slot in which no Input Card is installed.
• Attach the Input Card before mounting the monitor on the stand or wall mounting unit.
Installation
7 Installation procedure
1.
Remove the slot cover from the
slot on the bottom side of the
monitor.
4
Slot cover
The monitor in the illustration is GM-H40L2.
Installation (continued)
2.
Insert the Input Card into the slot,
fitting into the guides inside the
slot, so that its panel touches the
bottom of the monitor.
You can install the Input Card(s) into
either left or right slot. When installing,
follow the procedure below.
When installing two Input Cards:
•
Install either of Input Cards into the left
slot first.
•
When installing only one Input Card:
You need to attach the supplied slot
cover to the blank slot.
Install either Input Card or the supplied
slot cover into the left slot first as
illustrated on the right.
3.
Secure the Input Card by using the
screws removed in Step 1 on the
previous page.
Ex.: When installing only one Input Card
Panel
1, then 2.
Insert
Slot cover (supplied)
Slot cover (supplied)
Panel
Guide
or
Guide
ENGLISH
After installation
• Place the supplied labels on the rear panel and the
remote control of the monitor as illustrated on the right.
– On the rear panel: Place the label on the name of the
slot into which you have installed the Input Card.
– On the remote control: Place the label on the printing
of the corresponding input select buttons.
• Make sure the Input Card is correctly recognized by
“INPUT CONFIGURATION” (“INPUT C” – “INPUT F”) on
the main menu of the monitor.
On the rear panel
On the remote control
5
Controls and Features
Front view
Label
Rear view
6
1 Audio signal input terminals
Accepts analog audio signals.
Connect only the L/MONO terminal for monaural sound.
2 Composite signal input/output terminals
Accepts composite signals.
See page 8 for the signal formats compatible with this input card.
Select input by using the button on the monitor.
Input select: INPUT C (SLOT-1)/E (SLOT-2)
NTSC and PAL are switched by setting “COLOR SYSTEM” on the monitor. Refer to
your monitor instruction manual for more information.
NOTE:
• The IN and OUT terminals are bridge-connected (auto termination).
3 Synchronized signal input/output terminals
Accepts the synchronized signals (Black burst signals).
When using these terminals, set “SYNC SELECT” to “EXT.” on the monitor. Refer to
your monitor instruction manual for more information.
NOTE:
• The IN and OUT terminals are bridge-connected (auto termination).
4 Label (see page 5)
1 On the rear panel: Place the label on the name of the slot into which you have
installed the Input Card.
2 On the remote control: When the input signal type for input B is fixed (RGB,
COMPO., or DVI), place the corresponding label on the printing of the input select
buttons A and B.
3 On the remote control: Place the label on the printing of the input select buttons
(C/D or E/F) for the slot into which you have installed the Input Card. (“NO CARD” is
for a blank slot.)
ENGLISH
5 Connection terminal (on the rear side)
Attach to the connection terminal in the slot of your monitor.
7
Specifications
Model name: IF-CF01PNG
Type: Video Input Card
Target monitors: Consult your dealer.
Inputs/Outputs: Composite signal input/output:
VIDEO: 1 line, BNC x 2, 1.0 V(p-p), 75 Ω
• The IN and OUT terminals are bridge-connected (auto
termination).
Synchronized signal (Black burst signal) input/output:
EXT. SYNC: 1 line, BNC x 2, 0.3 V(p-p), 75 Ω
• The IN and OUT terminals are bridge-connected (auto
termination).
Audio signal input:
AUDIO (L/MONO, R): 1 line, RCA x 2, 0.5 V(rms)
Compliant signal format: NTSC, PAL, SECAM, PAL60, NTSC4.43, PAL M, PAL N,
BW (50 Hz/60 Hz)
Required slots: 1
Weight: 0.4 kg (0.9 lbs)
Dimensions (W x H x D): 133 mm x 34.5 mm x 185 mm
(5 1/4 inch x 1 3/8 inch x 7 3/8 inch)
7 Dimensions
Unit: mm (inch)
Front View (Terminal Side)
133 (5 1/4)
8
Top View
113 (4 1/2)
34.5
(1 3/8)
185
(7 3/8)
22 (7/8)
IF-CF01PNG VIDEO INPUT CARD
© 2006 Victor Company of Japan, Limited 0306MKH-MW-VP
Loading...