JVC GZ-R450, GZ-R450B User Guide

Basic User Guide

BC mark means complies with Energy Efficiency Law.

BC

HD MEMORY CAMERA

GZ-R450A

B5A-0799-00

EN

Detailed User Guide

.

For more details on operating this
product, please refer to the “Detailed
User Guide” at the following website.

http://manual3.jvckenwood.com/index.html/

o

Dear Customers

Thank you for purchasing this JVC product.
Before use, please read the Safety
Precautions and Cautions on p. 2 and
p. 19 to ensure safe use of this product.

When you are outside, refer to
the “Mobile User Guide”.
Mobile User Guide can be
viewed with standard browser
for Android tablet and iPhone.

o

For Future Reference:

Enter the Model No. (located on the bottom
of the camera) and Serial No.
(located on the bottom of the camera)
below.

Model No.
Serial No.

Mobile User Guide

.

http://manual3.jvckenwood.com/mobile/us/

Safety Precautions

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.

The lightning flash with arrowhead
symbol, within an equilateral
triangle, is intended to alert the
user to the presence of uninsulated

product's enclosure that may be of sufficient
magnitude to constitute a risk of electric shock
to persons.

instructions in the literature accompanying the
appliance.

0

0

0

0

"dangerous voltage" within the

The exclamation point within an
equilateral triangle is intended to
alert the user to the presence of
important operating and
maintenance (servicing)

For AC adapter only:
WARNING: TO REDUCE THE RISK OF

FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THE AC ADAPTER TO RAIN
OR MOISTURE.

Do not charge camcorder in area
exposed to rain or moisture.

NOTES:

The rating plate and safety caution are on
the bottom and/or the back of the main unit.
The serial number plate is on the bottom of
the main unit.
The rating information and safety caution of
the AC adapter are on its upper and/or lower
sides.

WARNING:

The camcorder with battery installed should
not be exposed to excessive heat such as
direct sunlight, fire or the like.

CAUTION:

A built-in lithium-ion battery is inside the unit.
When discarding the unit, environmental
problems must be considered and the local
rules or laws governing the disposal of these
batteries must be followed strictly.

Do not point the lens directly into the sun. This
can cause eye injuries, as well as lead to the
malfunctioning of internal circuitry. There is
also a risk of fire or electric shock.

CAUTION!

The following notes concern possible
physical damage to this unit and to the user.

Carrying or holding this unit by the LCD
monitor can result in dropping the unit, or in
a malfunction.

Do not use a tripod on unsteady or unlevel
surfaces. It could tip over, causing serious
damage to the unit.

CAUTION!

Connecting cables (Audio/Video, etc.) to this
unit and leaving it on top of the TV is not
recommended, as tripping on the cables will
cause this unit to fall, resulting in damage.

CAUTION:

The mains plug shall remain readily
operable.

Remove the mains plug immediately if the

0

camcorder functions abnormally.

2 EN

Make a backup of important recorded

Plug Adapter

data

JVC will not be responsible for any lost data.
It is recommended to copy your important
recorded data to a disc or other recording
media for storage once every 3 months.

IMPORTANT SAFETY INSTRUCTIONS

1.

Read these instructions.

2.

Keep these instructions.

3.

Heed all warnings.

4.

Follow all instructions.

5.

Clean only with dry cloth.

6.

Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.

7.

Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that
produce heat.

8.

Protect the power cord from being walked
on or pinched particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.

9.

Only use attachments/accessories
specified by the manufacturer.

.

Use only with the cart, stand, tripod, bracket,

10.
or table specified by the manufacturer, or
sold with the apparatus. When a cart is used,
use caution when moving the cart/
apparatus combination to avoid injury from
tip-over.

11.

Unplug this apparatus during lightning
storms or when unused for long periods of
time.

When using the AC adapter in areas
other than the USA

The provided AC adapter features automatic
voltage selection in the AC range from 110 V
to 240 V.

USING HOUSEHOLD AC PLUG ADAPTER

In case of connecting the unit’s power cord
to an AC wall outlet other than American
National Standard C73 series type use an AC
plug adapter, called a “Siemens Plug”, as
shown. For this AC plug adapter, consult your
nearest JVC dealer.

.

Remove the AC adapter from the AC wall

0

outlet when not in use.
Do not leave dust or metal objects adhered

0

to the AC wall outlet or AC adapter (power/
DC plug).
Be sure to use the supplied AC adapter.

0

Do not use the supplied AC adapter with

0

other devices.

If this symbol is shown, it is
only valid in the European
Union.

This product is licensed under the AVC
Patent Portfolio License for the personal use
of a consumer or other uses in which it does
not receive remuneration to (i) encode video
in compliance with the AVC standard (“AVC
Video”) and/or (ii) decode AVC Video that
was encoded by a consumer engaged in a
personal activity and/or was obtained from a
video provider licensed to provide AVC
Video. No license is granted or shall be
implied for any other use.

Additional information may be obtained from
MPEG LA, L.L.C.
See http://www.mpegla.com

EN 3

Remember that this unit is intended for
private consumer use only.

Any commercial use without proper
permission is prohibited. (Even if you record
an event such as a show, performance or
exhibition for personal enjoyment, it is
strongly recommended that you obtain
permission beforehand.)

Trademarks

AVCHD progressive and AVCHD

0

progressive logo are trademarks of
Panasonic Corporation and Sony
Corporation.
HDMI (High-

0

Definition Multimedia
Interface) and HDMI
logo are either registered trademarks or
trademarks of HDMI Licensing, LLC in the
United States and/or other countries.
Manufactured under license from Dolby

0

Laboratories. Dolby and the double-D
symbol are trademarks of Dolby
Laboratories.
SDXC logo is a trademark of SD-3C, LLC.

0

Windows® and Windows Vista® are either

0

registered trademarks or trademarks of
Microsoft Corporation in the United States
and/or other countries.
Apple, Mac, Mac OS, OS X, iMovie, iPhoto,

0

iPhone and Safari are trademarks of Apple
Inc., registered in the U.S. and other
countries.
Intel and Intel Core are trademarks or

0

registered trademarks of Intel Corporation
or its subsidiaries in the United States and
other countries.
Google™, Android™, YouTube™,

0

YouTube logo and Chrome™ are
trademarks and/or registered trademarks of
Google Inc.
Other product and company names

0

included in this instruction manual are
trademarks and/or registered trademarks of
their respective holders.
Marks such as ™ and ® have been omitted

0

in this manual.

.

This unit is equipped with Water
proof, Dust proof, Drop proof and
Freeze proof.

Water proof: Equivalent to IEC

Standard publication 529 IPX8
and IPX6 (30 minutes at depths
up to 5 m (16.4 ft))

Dust proof: Equivalent to IEC
Standard publication 529 IP5X

Drop proof: This camera clears
company testing compliant with
"MIL-STD-810F Method; 516.5
Shock: dropping onto plywood
3cm (1-3/16") thick from a
height of 1.5 m (4.9 ft)"

Freeze proof: Allowable
operating temperatures: −10°C
to +40°C (14°F to 104°F)
Note: Temperatures between

−10°C and 0°C (14°F and 32°F)
temporarily lower battery
performance, reducing the time
available for recording.

Precautions for waterproof function

0

Malfunction due to misuse by the
customer is not covered by warranty.

0

Before use in water, be sure to read and
understand the “Detailed User Guide”.

0

Close the terminal cover firmly until it
clicks and confirm that the red sign
completely goes off.

0

Make sure that there is no damage to and
no foreign material adhered to the
packing inside the cover.

0

Use the camcorder in marine water and
fresh water not deeper than 5 m or for not
more than 30 minutes.

0

The waterproof cannot be guaranteed if
the camcorder is subject to impact such
as dropping.

0

Do not jump or dive into water holding the
camcorder.

0

Do not use the camcorder in strong water
flows such as in rapids or under
waterfalls. The strong water pressure
may impair the waterproof performance.

0

Do not soak the camcorder in hot springs
or water of 40 °C or higher.

4 EN

Fogging inside the Lens

Open the terminal cover.

Lens protective glass

Models with waterproof function are airtight.
When the temperature rises during
recording, condensation can occur inside
the lens due to the internal humidity.

During recording

To prevent the temperature of this unit from
rising, we recommend that you use the unit
in the following ways.

Avoid frequent exposure to direct

A

sunlight.

Record under the shade or use an
umbrella. Best if you could keep a wet
towel cover the unit.

The use of a tripod is recommended.

B

Long hours of recording while holding the
unit in your hands will cause the
temperature of the unit to rise.

It is better to leave the terminal cover open

C

while recording.

However, the waterproof, dust-proof and
shockproof features do not function in this
condition. Do take note of the environment
when using the camera. (Do not use a wet
towel.)

Make sure to turn off the power when you

D

are not recording.

The power turns off when the LCD monitor
is closed.

During charging

It is recommended to charge the unit in a low
humidity environment.

The moist air inside the unit can cause
condensation.

We recommend that you charge the unit in a
room where humidifier is not in use, and in
an air-conditioned room during summer.

When fogging occurs inside the lens

Open the terminal cover to reduce the
temperature, close the LCD monitor and
leave the camera as it is for a while.

.

Protecting the Lens

This unit does not come with a lens cover and
lens cap.

However, there is a protective glass in front
of the lens to protect the lens.

0

It is recommended to put the camera in a
cloth bag when carrying it around.

0

If the protective glass is dirty, wipe clean
using a commercially available cleaning
cloth.

.

EN 5

MEMO

6 EN

Contents

Safety Precautions ................................. 2

Verifying the Accessories ...................... 7

Grip Belt Adjustment .............................. 8

Date and Time Setting
Open the terminal cover (SD card cover)

........................... 8

Getting Started

Charging the Battery ............................ 10

Inserting an SD Card ........................... 11

Recording

Video Recording .................................. 12

Playback

Playing Back/Deleting Files on this Unit

Copying

Install Everio MediaBrowser (Windows 8/Windows

8.1)

...... 9

....................................................... 15

Install Everio MediaBrowser (Windows 7 /
Windows Vista)

File Backup (Windows) ........................ 17

Working with iMovie and iPhoto ........... 18

Simple File Backup with a Mac ............ 18

...................................... 16

Further Information

Troubleshooting/Cautions .................... 19

Recordable Time/Specifications .......... 24

Verifying the Accessories

AC Adapter

AC-V11U

.

AV Cable

E3A-0085-00

.

0

Please

consult your JVC dealer or the nearest JVC service center when purchasing

a new AV cable.

Adapter Cable
QAM1580-001

.

Core Filter (Large)

(for AV Cable)

.

USB Cable

(Type A - Micro Type B)

.

Core Filter (small)

(for AC Adapter)

.

..... 14

Basic User Guide

(this manual)

.

EN 7

Grip Belt Adjustment

Adjust the length of the belt

Attach the padPull back the pad

Pad

SET DATE/TIME!

OK

201524 10 00

DEC

TIME

DATE

SAVE

DATE & TIME

GMT

SAVE

DATE & TIME/AREA

.

Date and Time Setting

Open the LCD monitor.

1

0

The unit turns on. When the LCD
monitor is closed, the unit turns off.

Tap [OK] when [SET DATE/

2

TIME!] is displayed.

.

Set the date and time.

3

0

0

4

5

0

0

When

the month, day, year, hour, or
minute item is tapped, 3 and 2 will
be displayed.
Tap 3 or 2 to adjust the value.

Repeat this step to input the month,
day, year, hour, and minute.

After setting the date and
time, tap [SAVE].

Select the region where you
live and tap [SAVE].

Time difference between the
selected city and the GMT
(Greenwich Mean Time) is
displayed.

Tap 0 or 1 to select the city name.

8 EN

.

.

Open the terminal cover (SD card cover)

Not properly closed if the red mark is visible!

(Rear)

Open the LCD monitor.

A

Slide down the terminal cover

B

lock and slide the cover aside
Lift the cover slowly.

C

To close

o

Leave the LCD monitor open first.

A

B

C

(The cover is not properly closed if the red mark at the terminal cover lock is
visible.)

.

down the cover slowly while making sure the gray waterproof seal fits into

Flip
the opening at the terminals.

Press the entire cover against the camcorder with equal force and firmly attach
the cover completely.

Slide the cover until it clicks into place.

CAUTION

0

Do not apply excessive force when opening or closing the terminal cover.

0

not open or close the terminal cover with wet or dirt/sand-covered hands.

Do

0

Do not allow any dirt, lint, hair, sand, and other foreign substances to
accumulate between the waterproof seal and the case.

0

Never damage or scratch the waterproof seal and terminal cover. Doing so
can result in leaks. If the seal is damaged, contact your nearest JVC Service
Center for a replacement. (Charges apply.)

0

Read the “Detailed User Guide” carefully before using the camcorder under
water or in places exposed to water droplet.

EN 9

Charging the Battery

To AC Outlet
(110 V to 240 V)

AC Adapter
(Provided)

Adapter Cable
(Provided)

Charging Lamp

A

B

C

D

A battery is built into the camcorder.

.

Open the terminal cover (p. 9)

1

Connect adapter cable to AC adapter.

2

Plug in the AC adapter to AC outlet (110 V to 240 V).

3

Connect the other side to USB socket on the unit.

4

CAUTION

0

At the time of purchase or in case of the battery is not used for a long period

time, the charging time will be longer than usual. The camera does not turn

of
on if the remaining battery power is low. In this case, charge the battery for
more than 40 minutes before turning on the power.

0

Charging time: Approx. 6 h 10 m (when charging at 25°C (77°F))

0

The battery cannot be charged outside the room temperature range of 10°C
to 35°C (50°F to 95°F). The CHARGE lamp does not light up when the battery
is not being charged. If the temperature increases or decreases during
charging, the CHARGE lamp will blink slowly and charging will stop. In this
case, remove the AC adapter, press the Reset button and wait until the room
temperature is within the above stated range before charging again.

0

You can record or play back videos during charging. (However, the charging
time will be longer than usual. In addition, the remaining battery power may
decrease according to conditions.) If the internal temperature rises when
using the unit, stop the charging temporarily. (The CHARGE lamp goes off.)

0

If malfunctions (such as overvoltage) occur, charging will stop. In this case,
the CHARGE lamp blinks quickly as a notification.

0

When the recording time becomes extremely short even when the battery is
fully charged, the battery needs to be replaced. For details on replacing the
built-in battery (subject to a fee), consult the nearest JVC service center.

0

For details on other charging methods, please refer to the “Detailed User Guide”.

10 EN

Inserting an SD Card

*

Insert an SD card.

Before inserting the SD card,
close the LCD monitor to turn off
this unit.

(Rear)

Label

Open the terminal cover.

The videos and the still images are recorded to the built-in memory at the initial
settings.

Insert a commercially available SD card if you want to record to the SD card.
For details on switching the media, please refer to the “Detailed User Guide”.

.

To remove the SD card

o

Push the SD card inward once, then pull it out straight.

NOTE

Operations are confirmed on the following SD cards.

Manufacturer Panasonic, TOSHIBA, SanDisk
Video A

Still Image B

0

Using SD cards (including SDHC/SDXC cards) other than those specified
above may result in recording failure or data loss.

0

This

unit is not guaranteed to operate with all SD cards, even when using the
ones specified above. Some SD cards may not work due to specification
changes, etc.

0

To protect the data, do not touch the terminals of the SD card.

0

When using an SDXC card, check its compatibility with the OS of your
computer by referring to the Detailed User Guide.

0

Do not use a miniSD card or microSD card (even if the card is inserted in an
adapter). It may cause malfunction to the camcorder.

Class 4 or higher compatible SD card (2 GB)/
Class 4 or higher compatible SDHC card (4 GB to 32 GB)/
Class 4 or higher compatible SDXC card (64 GB to 128 GB)

0

When recording with video quality [UXP], Class 6 or
higher is recommended.

SD card (256 MB to 2 GB) / SDHC card (4 GB to 32 GB) /
SDXC card (64 GB to 128 GB)

EN 11

Video Recording

H

P

A

C

A

T

W

Check if the recording
mode is A video.

If the mode is B still image,
tap B on the touch screen,
then tap A to switch.

Start recording.

Press again to stop.

Zooming

(Wide angle)

(Telephoto)

Zoom Lever

If the mode is H Manual, tap H on
the touch screen, then tap P to
switch.

Check if the recording mode
is P.

You can record without worrying about the setting details by using the P
Auto) mode. Settings such as exposure and focus will be adjusted automatically to
suit the shooting conditions.

Before recording an important scene, it is recommended to conduct a trial recording.

(Intelligent

.

0

You can also tap 6 on the touch screen to record. To stop recording, tap

7

. In addition, you can also tap D to zoom.

12 EN

Indications during video recording

MENU

≪PLAY

0:00:00 [0:54]

REC

Recording in Progress
Recording-Standby

Battery Indicator

Recording Media

Image Stabilizer

Video Quality

Remaining Recording
Time

Scene Counter

Still Image

Recording Button

Release the
stopper.

To be connected to this unit

3 cm (1-3/16”)

Wind twice (for AC Adapter cable)

Wind once (for AV Cable)

o

.

NOTE

0

The estimated recording time of the supplied battery is approximately 2 hour
50 minutes of actual recording and up to 4 hours 50 minutes of continuous
recording.

0

Do not remove SD card when the POWER/ACCESS lamp is lighted. The
recorded data may become unreadable.

0

With [AUTO POWER OFF] operation, the camera automatically turns off if no
operation is performed for 5 minute, in order to conserve power. (The unit
enters into standby mode when the AC adapter is used.)

0

The angle of view may change when the image stabilizer is turned on or off.

0

When recording underwater, the internal mechanical noise (such as zooming
sound) may be easily picked up and recorded. This is not a malfunction.

Attaching the Core Filter

o

Attach the core filter to the AV Cable and the AC Adapter cable as shown in the
illustration.
devices.

0

Use the small core filter for the AC Adapter cable and the big core filter for the
AV Cable.

0

Do not attach the core filter to the supplied Adapter Cable.

The core filter reduces interference when this unit is connected to other

.

EN 13

Playing Back/Deleting Files on this Unit

T

W

VOL.

＋

Tap on the files to delete.

Ta p R.

To delete unwanted files

Turn up the
volume

Turn down

the volume

Volume adjustment
during playback

Ta p u to return to the video
index screen.

Tap on the file to play back.

Tap "SET".

Ta p E to return to the
recording mode.

Ta p F on the touch screen
to select the playback mode.

Ta p e to pause playback.

Tap "OK".

Tap "EXECUTE" when the
confirmation message appears.

Ta p A or B to select the video
or still image mode.

A I mark appears on the selected file.
To remove the I mark, tap again.

DELETE

SEL ALL REL ALL SET

QUIT

Select and play back the recorded videos or still images from an index screen (thumbnail
display).

.

0

When playing back videos recorded in 60p mode (select [60p] in [SYSTEM
SELECT]), please refer to the “Detailed User Guide”.

To capture a still image during playback

o

A

Pause the playback with e.

B

Press the START/STOP button or tap the A on the LCD.

NOTE

0

While this unit may be used with the LCD monitor reversed and closed, the
temperature rises more easily. Leave the LCD monitor open when using this
unit.

0

power may turn off to protect the circuit if the temperature of this unit rises

The
too much.

14 EN

Install Everio MediaBrowser

To USB
Connector

USB Cable
(Provided)

To USB
Connector

PLAYBACK ON PC

CONNECT TO PC

(Windows 8/Windows 8.1)

Everio MediaBrowser is included with
your camera. It lets you archive and
organize your videos. It also lets you
create discs and upload video to
YouTube, and other popular web sites.

Open the terminal cover.

1

Connect the USB cable.

2

0

Before connecting the USB cable,
close the LCD monitor to turn the
camera off.

.

Open the LCD monitor to

3

turn on this unit.

Operation on the camera's touch

o

screen:

Tap [CONNECT TO PC].

4

Operation on the computer:

o

Perform the following steps.

6

Display “Apps”.

A

(Windows 8)
Click “Search” charm.
(Windows 8.1)
Click F.

Click “Computer” in the

B

“Windows System Tool” menu.

0

If

a “Computer” icon is shown on
desktop, double-click the icon
to open the “Computer” menu.

Double-click the

C

“JVCCAM_APP” icon in the
“Devices with Removable
Storage” menu.

Double-click “install”.

D

Click "Yes" on the User Account

E

Control screen.

0

“Software Setup” appears after
a while.

Click “Everio MediaBrowser

7

4”.

Tap [PLAYBACK ON PC].

5

.

.

0

Follow the on-screen instructions.

Click “Finish”.

8

Click “Quit”.

9

0

Installation ends and icons are
created on the desktop.

EN 15

Install Everio MediaBrowser

To USB
Connector

USB Cable
(Provided)

To USB
Connector

PLAYBACK ON PC

CONNECT TO PC

(Windows 7 / Windows Vista)

Everio MediaBrowser is included with
your camera. It lets you archive and
organize your videos. It also lets you
create discs and upload video to
YouTube, and other popular web sites.

Open the terminal cover.

1

Connect the USB cable.

2

0

Before connecting the USB cable,
close the LCD monitor to turn the
camera off.

.

Open the LCD monitor to

3

turn on this unit.

Operation on the camera's touch

o

screen:

Tap [CONNECT TO PC].

4

Tap [PLAYBACK ON PC].

5

Operation on the computer:

o

Perform the following steps.

6

For Windows Vista, click

A

“Allow”.
Click

“Run INSTALL.EXE” in the

B

auto play dialog box.
Click “Continue” on the user

C

account control screen.

0

“Software Setup” appears after
a while.

0

If it doesn’t appear, double-click
“JVCCAM_APP” in “My
Computer” (or “Computer”),
then double-click the
“install.exe”.

Click “Everio MediaBrowser

7

4”.

.

0

Follow the on-screen instructions.

Click “Finish”.

8

Click “Quit”.

9

16 EN

.

.

0

Installation ends and icons are
created on the desktop.

File Backup (Windows)

To USB
Connector

USB Cable
(Provided)

To USB
Connector

CONNECT TO PC

BACK UP

2

1

Click

Click

Click

Saving destination (PC)

Preparation:

0

Install the Everio MediaBrowser
software onto the computer.

0

Make

sure that enough space is left in

the HDD of computer.

Open the terminal cover.

1

Connect the USB cable.

2

0

Before connecting the USB cable,
close the LCD monitor to turn the
camera off.

.

Open the LCD monitor to

3

turn on this unit.

Operation on the camera's touch

o

screen:

Tap [CONNECT TO PC].

4

Tap [BACK UP].

5

Operation on the computer:

o

6

0

Select “All volume in camcorder”,
then click “Next”.

.

7

0

Make
of files, then click “Start”.

.

0

File backup is only supported by
the provided software.

Select files.

Start backup.

sure of the saving destination

NOTE

.

0

Everio MediaBrowser starts on the
computer.

EN 17

Working with iMovie and iPhoto

USB cable
(Provided)

To USB
port

To USB
Connector

USB cable
(Provided)

To USB
port

To USB
Connector

PLAYBACK ON PC

CONNECT TO PC

0

You may use the software supplied
with the Mac Computer to view and
edit files from the camera.

0

Connect the camera to the Mac
Computer using a USB Cable.

.

iMovie and iPhoto

o

You can import files from this unit to a
computer using Apple’s iMovie '11,
Version 10 or iPhoto.
To verify the system requirements of
iMovie and iPhoto, refer to the Apple's
user guides.

NOTE

0

For the latest information on iMovie or
iPhoto, refer to the Apple website.

0

For details on how to use iMovie or
iPhoto, refer to the help file of the
software.

0

NOTE

0

Files must be transferred to the
Mac Computer for editing.

There is no guarantee that the
operations will work with all computer
environments.

Simple File Backup with a Mac

Preparation:

0

sure that enough space is left in

Make
the Mac’s HDD.

0

Before connecting the USB cable to
camcorder, close the LCD monitor to
turn it off.

Connect the USB cable.

1

.

0

Then open the LCD monitor to turn
on the camera.

18 EN

Tap [CONNECT TO PC] on

2

the camera’s touch screen.

Tap [PLAYBACK ON PC]
on the camera’s touch

3

screen.

.

Import the files.

4

0

Import the files after iPhoto
automatically runs.

0

Import the video using iMovie if you
want to edit it.

Troubleshooting/Cautions

ATTENTION:

0

To avoid hazards

…

Troubleshooting

If you encounter problems with this unit,
check the following before requesting
service.

1. Refer to the “Troubleshooting” section
in the “Detailed User Guide”.

If you have difficulties operating the
unit,

refer to the detailed descriptions

in the “Detailed User Guide”.
http://manual3.jvckenwood.com/

index.html/

2. This unit is a microcomputer-controlled
device. Electrostatic discharge,
external noise and interference (from a
TV, a radio, etc.) might prevent it from
functioning properly.

In such a case, reset the unit.

Remove all the cables from this

A

unit.
Press the "Reset button" located

B

inside

of the terminal cover. (Before
pressing the reset button, close the
LCD monitor to turn off this unit.)

Reattach the AC adapter, open the

C

LCD monitor and this unit powers
on automatically.

3. If the above do not solve the problem,
consult your nearest JVC dealer or
JVC service center.

Built-in Battery

This unit is equipped with a built-in
lithium-ion battery. Before using this
Unit, be sure to read the following
cautions:

do not burn.

…

do not modify or disassemble.

…

do not expose this Unit to temperatures
exceeding 60°C (140°F), as this may
cause the built-in battery to overheat,
explode or catch fire.

0

To prevent damage and prolong
service life

…

do not subject to unnecessary shock.

…

charge within the temperature range of
10°C to 35°C (50°F to 95°F). Cooler
temperatures require longer charging
time, or in some cases stop charging at
all.

Warmer temperatures prevent complete
charging,

or in some cases stop charging

at all.

…

store in a cool, dry place. Extended
exposure to high temperatures will
increase natural discharge and shorten
service life.

…

keep a 30% battery level (i) if the
battery is not to be used for a long period
of time.
In addition, fully charge and then fully
discharge the battery every 6 months,
then continue to store it at a 30% battery
level (i).

…

remove the AC adapter from the unit
when not in use, as some machines use
current even when switched off.

…

do not drop intentionally or subject to
strong impact.

The product you have
purchased is powered by a
rechargeable battery that is
recyclable.

Please call 1-800-8-BATTERY for
information on how to recycle this
battery.

(USA and Canada only)

EN 19

Recording Medium

0

Be sure to follow the guidelines
below to prevent corruption or
damage to your recorded data.

Do not bend or drop the recording

0

medium, or subject it to strong
pressure, jolts or vibrations.
Do not splash the recording medium

0

with water.
Do not use, replace, or store the

0

0

0

0

0

0

When erasing data using the
camcorder, the data won’t be erased
completely. When handing over your
camcorder and/or SD card, you are
recommended to erase all of the data
by either performing “FORMAT” or
“FACTORY PRESET” operation on
this unit, using commercially available
software, or by physically destroying
the camcorder.

medium in locations that are

recording
exposed to strong static electricity or
electrical noise.
Do not turn off the camcorder power
during shooting, playback, or when
otherwise accessing the recording
medium.
Do not bring the recording medium
near objects that have a strong
magnetic field or that emit strong
electromagnetic waves.
Do not store the recording medium in
locations with high temperature or high
humidity.
Do not touch the metal parts.

LCD Monitor

0

To prevent damage to the LCD
monitor, DO NOT

…

push it strongly or apply any shocks.

…

the camcorder with LCD monitor

place
on the bottom.

0

To prolong service life

…

avoid rubbing it with coarse cloth.

While the LCD monitor screen has
more than 99.99% effective pixels,

0.01% of the pixels may be bright
spots

(red, blue, green) or dark spots.
This is not a malfunction. The spots
will not be recorded.

Main Unit

0

For safety, DO NOT

…

open the camcorder’s chassis.

…

disassemble or modify the unit.

…

allow inflammables, water or metallic
objects to enter the unit.

…

place naked flame sources, such as
lighted candles, on the apparatus.

…

dust or metal objects adhered to

leave
the power plug or an AC wall outlet.

…

insert any objects in the camcorder.

0

Avoid using the unit

…

in places subject to soot or steam such
as near a cooking stove.

…

in places subject to excessive shock
or vibration.

…

near a television set.

…

near appliances generating strong
magnetic or electric fields (speakers,
broadcasting antennas, etc.).

…

in places subject to extremely high
(over 40°C or 104°F) or extremely low
(under -10°C or 14°F) temperatures.

0

DO NOT leave the unit

…

in places of over 50°C (122°F).

…

in places where humidity is extremely
low (below 35 %) or extremely high
(above 80 %) with the terminal cover
open.

…

in direct sunlight.

…

in a closed car in summer.

…

near a heater.

…

in high places such as on a TV.
Leaving the unit in high places while a
cable is connected may result in a
malfunction if the cable is caught and
the unit falls onto the floor.

20 EN

0

To protect the unit, DO NOT

…

drop the unit or strike it against hard
objects.

…

subject it to shock or excessive
vibration during transportation.

…

keep the lens directed at extremely
bright objects for long periods.

…

expose the lens to direct sunlight.

…

swing it excessively when using the
hand strap.

…

swing the soft camcorder case
excessively when the camcorder is
inside it.

…

cover camcorder with a towel, cloth
and so on.

0

To prevent the unit from dropping

0

Fasten the grip belt securely.

0

When using the camcorder with a
tripod, attach the camcorder to the
tripod securely.

If the camcorder drops, you may be
injured and the camcorder may be
damaged.

When a child uses the unit, there must
be parental guidance.

Declaration of Conformity

Model Number : GZ-R450U
Trade Name : JVC
Responsible party :

JVCKENWOOD USA Corporation
Address : 1700 Valley Road Wayne,

N. J. 07470
Telephone Number : 973-317-5000
This device complies with Part 15 of

FCC Rules. Operation is subject to
the following two conditions: (1) This
device may not cause harmful
interference, and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.

Changes or modifications not
approved by JVC could void the
user’s authority to operate the
equipment.
tested and found to comply with the
limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against
harmful interference in a residential
installation. This equipment
generates, uses, and can radiate
radio frequency energy and, if not
installed and used in accordance with
the instructions, may cause harmful
interference to radio
communications. However, there is
no guarantee that interference will not
occur in a particular installation. If this
equipment does cause harmful
interference to radio or television
reception, which can be determined
by turning the equipment off and on,
the user is encouraged to try to
correct the interference by one or
more of the following measures:
Reorient or relocate the receiving
antenna. Increase the separation
between the equipment and receiver.
Connect the equipment into an outlet
on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced
radio/TV technician for help.

Refer all servicing to qualified service
personnel. Servicing is required
when the apparatus has been
damaged
supply cord or plug is damaged,
objects have fallen into the
apparatus, ingress of water into the
unit, does not operate normally.

This equipment has been

in any way, such as power-

EN 21

MEMO

22 EN