Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)
This service manual (No.YF365<Rev.001>) describes only the items which differ from those of already issued service manual
(No.YF362
For details other than those described in this manual, please refer to the service manuals which were already issued.
Prior to shipment from the factory, JVC products are strictly
inspected to conform with the recognized product safety and
electrical codes of the countries in which they are to be
sold.However,in order to maintain such compliance, it is equally
important to implement the following precautions when a set is
being serviced.
1.1.1 Precautions during Servicing
(1) Locations requiring special caution are denoted by labels
and inscriptions on the cabinet, chassis and certain parts of
the product.When performing service, be sure to read and
comply with these and other cautionary notices appearing
in the operation and service manuals.
(2) Parts identified by the symbol and shaded ( ) parts
are critical for safety.
Replace only with specified part numbers.
NOTE :
Parts in this category also include those specified to
comply with X-ray emission standards for products
using cathode ray tubes and those specified for
compliance with various regulations regarding
spurious radiation emission.
(3) Fuse replacement caution notice.
Caution for continued protection against fire hazard.
Replace only with same type and rated fuse(s) as
specified.
(4) Use specified internal wiring. Note especially:
• Wires covered with PVC tubing
• Double insulated wires
• High voltage leads
(5) Use specified insulating materials for hazardous live parts.
Note especially:
• Insulation Tape
• PVC tubing
•Spacers
• Insulation sheets for transistors
• Barrier
(6) When replacing AC primary side components (transformers,
power cords, noise blocking capacitors, etc.) wrap ends of
wires securely about the terminals before soldering.
can increase the high voltage value and cause X-ray emission from the cathode ray tube.
(12) Crimp type wire connector
In such cases as when replacing the power transformer in
sets where the connections between the power cord and
power trans former primary lead wires are performed using
crimp type connectors, if replacing the connectors is unavoidable, in order to prevent safety hazards, perform
carefully and precisely according to the following steps.
• Connector part number: E03830-001
• Required tool: Connector crimping tool of the proper
type which will not damage insulated parts.
• Replacement procedure
a) Remove the old connector by cutting the wires at a
point close to the connector.Important: Do not
reuse a connector (discard it).
cut close to connector
Fig.1-1-3
b) Strip about 15 mm of the insulation from the ends
of the wires. If the wires are stranded, twist the
strands to avoid frayed conductors.
15 mm
Fig.1-1-4
c) Align the lengths of the wires to be connected.
Insert the wires fully into the connector.
Metal sleeve
(7) Observe that wires do not contact heat producing parts
Fig.1-1-1
(heatsinks, oxide metal film resistors, fusible resistors, etc.)
(8) Check that replaced wires do not contact sharp edged or
pointed parts.
(9) When a power cord has been replaced, check that 10-15
kg of force in any direction will not loosen it.
Power cord
Fig.1-1-2
(10) Also check areas surrounding repaired locations.
(11) Products using cathode ray tubes (CRTs)
In regard to such products, the cathode ray tubes themselves, the high voltage circuits, and related circuits are
specified for compliance with recognized codes pertaining
to X-ray emission. Consequently, when servicing these
products, replace the cathode ray tubes and other parts
with only the specified parts. Under no circumstances attempt to modify these circuits.Unauthorized modification
1-2 (No.YF365<Rev.001>)
Connector
Fig.1-1-5
d) As shown in Fig.1-1-6, use the crimping tool to crimp
the metal sleeve at the center position. Be sure to
crimp fully to the complete closure of the tool.
1.2
5
2.0
5.5
Crimping tool
Fig.1-1-6
e) Check the four points noted in Fig.1-1-7.
Not easily pulled free
Wire insulation recessed
more than 4 mm
Crimped at approx. cente
of metal sleeve
Conductors extended
Fig.1-1-7
1.1.2 Safety Check after Servicing
Examine the area surrounding the repaired location for damage
or deterioration. Observe that screws, parts and wires have been
returned to original positions, Afterwards, perform the following
tests and confirm the specified values in order to verify
compliance with safety standards.
(1) Insulation resistance test
Confirm the specified insulation resistance or greater
between power cord plug prongs and externally exposed
parts of the set (RF terminals, antenna terminals, video and
audio input and output terminals, microphone jacks,
earphone jacks, etc.).See table 1 below.
(2) Dielectric strength test
Confirm specified dielectric strength or greater between
power cord plug prongs and exposed accessible parts of
the set (RF terminals, antenna terminals, video and audio
input and output terminals, microphone jacks, earphone
jacks, etc.). See Fig.1-1-11 below.
(3) Clearance distance
When replacing primary circuit components, confirm
specified clearance distance (d), (d') between soldered
terminals, and between terminals and surrounding metallic
parts. See Fig.1-1-11 below.
d
Chassis
d'
Power cord
primary wire
Fig.1-1-8
(4) Leakage current test
Confirm specified or lower leakage current between earth
ground/power cord plug prongs and externally exposed
accessible parts (RF terminals, antenna terminals, video
and audio input and output terminals, microphone jacks,
earphone jacks, etc.).
Measuring Method: (Power ON) Insert load Z between
earth ground/power cord plug prongs and externally
exposed accessible parts. Use an AC voltmeter to
measure across both terminals of load Z. See Fig.1-1-9
and following Fig.1-1-12.
ab
Externally
exposed
accessible part
Z
V
c
A
Fig.1-1-9
(5) Grounding (Class 1 model only)
Confirm specified or lower grounding impedance between
earth pin in AC inlet and externally exposed accessible
parts (Video in, Video out, Audio in, Audio out or Fixing
screw etc.).Measuring Method:
Connect milliohm meter between earth pin in AC inlet and
exposed accessible parts. See Fig.1-1-10 and grounding
specifications.
AC inlet
Earth pin
Exposed accessible part
MIlli ohm meter
Grounding Specifications
Region
USA & Canada
Europe & Australia
Grounding Impedance (Z
Z0.1 ohm
Z0.5 ohm
)
Fig.1-1-10
AC Line Voltage
100 V
100 to 240 V
110 to 130 V
110 to 130 V
200 to 240 V
Region
Japan
USA & Canada
Europe & Australia
Insulation Resistance (R
R 1 M /500 V DC
1 M R 12 M /500 V DC
R 10 M /500 V DC
)
Dielectric Strength
AC 1 kV 1 minute
AC 1.5 kV 1 minute
AC 1 kV 1 minute
AC 3 kV 1 minute
AC 1.5 kV 1 minute
(
Class
(
Class
Clearance Distance (d), (d'
d, d' 3 mm
d, d' 4 mm
d, d' 3.2 mm
d 4 m m
)
d' 8 m m (Power cord
d' 6 m m (Primary wire
)
Fig.1-1-11
AC Line Voltage
100 V
110 to 130 V
110 to 130 V
220 to 240 V
Region
Japan
USA & Canada
Europe & Australia
Load Z
1
0.15
1.5
2
50
Leakage Current (i)
i 1 mA rms
i 0.5 mA rms
i 0.7 mA peak
i 2 mA dc
i 0.7 mA peak
i 2 mA dc
a, b, c
Exposed accessible parts
Exposed accessible parts
Antenna earth terminals
Other terminals
Fig.1-1-12
NOTE:
These tables are unofficial and for reference only. Be sure to confirm the precise values for your particular country and locality.
)
)
)
(No.YF365<Rev.001>)1-3
SECTION 2
SPECIFIC SERVICE INSTRUCTIONS
2.1DIFFERENCE LIST
MODELGZ-HM30BKRGZ-HM30BUAGZ-HM30BUB
COMPONENT CONN.NOYESYES
AC CORDKR TYPEIRAM TYPEBRAZIL TYPE
BATTERYBN-VG107KRBN-VG107EUBN-VG107EU
1-4 (No.YF365<Rev.001>)
3.1Disassembly procedure
SECTION 3
DISASSEMBLY
2
(S1b)
3
(S1b)
L1c
step2
Fig.3-1-1
[1]TOP COVER ASSY
L1d
2
(S1b)
(S1b)
L1b
L1a
1
(S1a)
step1
3
L1e
5
(S3a)
6
(S3a)
8
(S3b)
L3
(S3b)
8
(S3b)
6
(S3a)
7
(S3b)
[3]LOWER CASE ASSY
Fig.3-1-3
7
5
(S3a)
9
(S3c)
L2c
[2]WINDOW(WB)
L2a
4
(S2)
L2b
L2c
11
(S4a)
10
(S4a)
12
(S4a)
10
(S4a)
11
(S4a)
L4
13
(S4b)
CN4
12
(S4a)
FPC
[4]FRONT ASSY
(Incl.MICROPHONE UNIT,SHUTTER ASSY)
Fig.3-1-2
Fig.3-1-4
(No.YF365<Rev.001>)1-5
14
(S5)
HOOK
HOOK
L5c
L5b
L5a
step1
CN5
Fig.3-1-5
[5]OPE UNIT
step2
<FPC>
FPC
FPC
<FPC>
REAR B. ASSY
MAIN B. ASSY
FPC
CN6f
CN6e
e
L6a
e
CN6b
L6b
f
b
15
(S6)
CN6g
f
b
g
c
Fig.3-1-6
(S6)
g
a
c
CN6a
CN6c
d
16
d
CN6d
a
[6]MAIN BOARD ASSY
<CONNECTOR>
b
c
a
HOOK
a
MAIN B. ASSY
d
1-6 (No.YF365<Rev.001>)
HOLE
SWITCH
[7]REAR COVER ASSY
(Incl.REAR BOARD ASSY)
L7a
17
(S7a)
18
L7b
(S7b)
*
.
*
23
.
cm)m(1.2kgf:0.118N
<FPC>
FPC(CMOS)
23
(S9)
RIB(UPPER CASE)
(S9)
*
22
UPPER ASSY
(S9)
19
(S7b)
18
(S7b)
17
(S7a)
[8]SHIELD(MAIN)
20
(S8a)
19
(S7b)
Fig.3-1-7
L7c
HOLE
L8a
20
(S8a)
24
(S9)
[9]OP BLOCK ASSY
(Incl.CMOS FRM ASSY)
Fig.3-1-9
L10b
[4]FRONT ASSY
L10a
[11]MICROPHONE UNIT
HOOK
L11
*
LEVER
(open)
21
(S8b)
L8a
L8c
L8b
Fig.3-1-8
PLATE(MIC)
HOOK
[10]SHUTTER ASSY
L11
Fig.3-1-10
27
(S11)
(No.YF365<Rev.001>)1-7
26
(S10)
25
(S10)
L12a
[7]REAR COVER ASSY
[12] REAR BOARD ASSY
L12b
L12b
Fig.3-1-11
MONITOR ASSY
[13]UPPER ASSY
(Incl.TRIPOD BASE ASSY,SPEAKER)
*
30
(S13b)
Fig.3-1-12
(S13b)
L13c
*
31
28
(S13a)
29
(S13a)
*
28
(S13a)
:0.245N m(2.5kgf cm)
29
(S13a)
.
L13b
.
L13a
1-8 (No.YF365<Rev.001>)
[14]TRIPOD BASE ASSY
(Incl.JACK BOARD ASSY)
L14a
L14b
HOOK
(S14)
HOOK
32
L14a
L14b
L14c
L14c
HOOK
OK
OK
NG
[16]SPEAKER
35
(S16)
BKT(SPK)
33
(S14)
32
(S14)
33
(S14)
Fig.3-1-13
34
(S15)
[15]JACK BOARD ASSY
L14c
<WIRE>
L16
HOOK
UPPER FRAME ASSY
Fig.3-1-15
[14]TRIPOD BASE ASSY
Fig.3-1-14
L15
(No.YF365<Rev.001>)1-9
MONITOR COVER ASSY
L17a
L17h
L17b
L17g
L17c
ATTACH
(S17a)
*
37
(S17a)
36
L17f
*
L17e
L17d
*
37
(S17a)
*
36
(S17a)
L17j
L17k
FPC
HINGE UNIT
*
.
.
cm)m(2.5kgf:0.245N
CN17a
Fig.3-1-16a
HINGE UNIT
FPC
Roll 2.5 rotations
L17p
L17s
L17n
HINGE COVER (U)
L17m
HINGE COVER (L)
L17q
L17r
Fig.3-1-16b
MAGNET
<OK>
MAGNET
<NG>
S POLE SIDE
N POLE SIDE
1-10 (No.YF365<Rev.001>)
38
(S17b)
39
(S17b)
MONITOR BOARD ASSY
b
CN17b
*
42
(S18)
[18]CMOS FRM ASSY
SHEET
*
41
(S18)
(S18)
*
40
Fig.3-1-16c
SHEET(M.REF)
LIGHT GUIDE
SHEET(M.DIFF)
SHEET BEF(SUB)
L17t
b
IR CUT FILTER
:0.118N m(1.2kgf cm)
*
.
Fig.3-1-17
L18
.
SHEET BEF(MAIN)
SHEET CLEARANCE
LCD MODULE
MONI. CASE ASSY
(Incl. LCD CASE,BKT LCD)
Fig.3-1-16d
(No.YF365<Rev.001>)1-11
3.2Quality point
When you assemble the unit, please check the following points for keeping the quality.
[1] TOP COVER ASSY
Fig.3-1-1
OKNG
When attaching the TOP COVER, properly
set the rear side.
[2] WINDOW (WB)
Fig.3-1-2
[9] OP BLOCK ASSY
Fig.3-1-9
OKNG
Between the CMOS and the MAIN, run the FPC
under the mold.
[10] SHUTTER ASSY
Fig.3-1-10
To attach the WINDOW (WB), slide it under the FRONT COVER.
Be careful not to set the WINDOW (WB) over the FRONT COVER.
[4] FRONT ASSY
Fig.3-1-4
OKNG
Run the MIC FPC inside the FRONT COVER.
[6] MAIN BOARD ASSY
Fig.3-1-6
OKNG
To replace the BARRIER UNIT, open the BARRIER to check the screws.
(The screws cannot be observed with the BARRIER closed.)
[12] REAR BOARD ASSY
Fig.3-1-11
OKNG
Be careful not to insert the FPC in reverse direction
paying attention to the PET affixed position.
[18] CMOS FRM ASSY
Fig.3-1-17
Between the JACK and the MAIN, do not catch the
FFC with the BOTTOM.
1-12 (No.YF365<Rev.001>)
Do not apply excessive shock to the CMOS ASSY.
SECTION 4
ADJUSTMENT
4.1PREPARATION
4.1.1 Precaution
This model is specially adjusted by using PC.
However, if parts such as the following are replaced, an
adjustment is required. The adjustment must be performed in a
Service Center equipped with the concerned facilities.
• OP BLOCK ASSEMBLY
• MONITOR ASSEMBLY
• EEP ROM (IC1003 of MAIN board)
In the event of malfunction with electrical circuits, first find a
defective portion with the aid of proper test instruments as shown
in the following electrical adjustment procedure, and then
commence necessary repair/ replacement/adjustment.
• In observing chip TP, use IC clips, etc. to avoid any stress.
Prior to replacement of chip parts (especially IC), remove the
solder completely to prevent peeling of the pattern.
• Since connectors are fragile, carefully handle them in
disconnecting and connecting the FPC.
4.1.2 Required test equipment
• Personal computer (for Windows)
• Color TV monitor
• Oscilloscope (dual-trace type, observable 100MHz or higher
frequency). The one observable 300 MHz or higher frequency
is recommended.
• Digital voltmeter
• DC power supply or AC adapter
• Frequency counter (with threshold level adjuster)
4.1.3 Tools required for adjustment
Torque Driver
YTU94088
Chip IC Replacement Jig
PTS40844-2
INF Adjustment Lens Holder
YTU94087
Bit
YTU94088-003
Cleaning Cloth
KSMM-01
Mini Stand
YTU93108
Tweezers
P-895
INF Adjustment Lens
YTU92001E
Light Box Assembly
YTU93096B
• Torque Driver
Be sure to use to fastening the mechanism and exterior parts
because those parts must strictly be controlled for tightening
torque.
• Bit
This bit is slightly longer than those set in conventional torque
drivers.
• Tweezers
To be used for removing and installing parts and wires.
• Chip IC Replacement Jig
To be used for adjustment of the camera system.
• Cleaning Cloth
To be used to wipe down the LCD screen and the optical lens
surface.
• INF Adjustment Lens
To be used for adjustment of the camera system. For the
usage of the INF adjustment lens, refer to the Service Bulletin
No. YA-SB-10035 and No. YA-SB-10223.
• INF Adjustment Lens Holder
To be used together with the Camera stand for operating the
Videocamera in the stripped-down condition such as the status without the exterior parts or for using commodities that are
not yet conformable to the interchangeable ring. For the usage
of the INF lens holder, refer to the Service Bulletin No. YA-SB-
10035.
• Mini Stand
To be used together with the INF adjustment lens holder. For
the usage of the Mini stand, refer to the Service Bulletin No.
YA-SB-10035.
• Light Box Assembly
To be used for adjustment of the camera system. For the
usage of the Light box assembly, refer to the Service Bulletin
No. YA-SB-10035 and No. YA-SB-10218.
• Jig Connector Cable
Connected to JIG CONNECTOR of the main board and used
for electrical adjustment, etc.
• PC Cable
To be used to connect the Videocamera and a personal computer
with each other when a personal computer issued for adjustment.
• Service Support System
To be used for adjustment with a personal computer. Software
can be downloaded also from JS-net.
Jig Connector Cable
YTU43192
PC Cable
QAM0099-002
Service Support System
YTU94057-128
(Software)
(No.YF365<Rev.001>)1-13
4.2JIG CONNECTOR CABLE CONNECTION
Connection procedure
Remove the 3 screws (1-3), and then remove the TOP COVER
ASSY.
Prepare the specified screws and use them in place of the removed screws.
Symbol No.
Place to stick screw
Removing order of screw
Screw tightening torque
Reference drawing (Fig.No.)
Symbol No.
Place to stick screw
Removing order of screw
Reference drawing (Fig.No.)
Screw tightening torque
and (This mark shows where to attach the screws) : Do not reuse the screws because the screw lock bond was applied to prevent the screws from loosening.
Tightening torque for the screws
NOTE:
m (0.9kgf cm)0.088Nam (1.2kgf cm)0.118Nbm (2.5kgf cm)0.245Nc
Be careful not to break either the screws or the screw holes.
and tighten the screw manually.
The specified torque value is a recommended value of the initial assembly. Therefore, set the value below the specified torque value in the assembling procedure.
There are setting limits of the torque value for the torque driver. If the value exceeds the setting value, take it as a rough measurement (reference value),
Note : The parts numbers in the schematic diagram are for references only.
When replacing the parts, refer to the PARTS LIST.
9
0
1
MAIN(AUDIO(STEREO))
yf362_y10890001a8/9_1124_ver0.1
To Woflson(IC 2201)
To Woflson(IC 2201)
TO Speaker
From INT_MIC
AUDIO_PD_L
AUDIO_PD_L
AIOLRCK
AOMCLK
AUDIO_CS
AUDIO_OUT
AUDIO_OUT
AUDIO_CS
AUDIO_CLK
AIOBCK
AOBD
AOBD
AIOBCK
AIBD
AUDIO_CLK
AOMCLK
AIOLRCK
SPK-
GND
SPK+
SPK-
AIBD
INT_LM
AU_SIG/R
AVDD
AU_SIG/LM
V_OUT
AUDIO_PD_L
REG_2.8V
SYIN
AUDIO_CLK
AIOLRCK
AUDIO_CS
AUDIO_OUT
INT_R
REG_1.8V
AOBD
INT_L
REG_5.0V
GND
AOMCLK
AIOBCK
M_GND
L_MUTE
18k
*R2463
2.2k
*R2162
820
*R2661
4.7k
*R2462
NRSA6AJ-0R0W
ǡ
*K2103
OPEN
560k
*R2664
OPEN
560k
*R2663
10
*R2464
75
*R3246
2.2k
*R2161
NRSA6AJ-0R0W
ǡ
*K2102
820
*R2662
*Q2662
2SC5383/F/-X
*Q2462
654
321
*Q2661
10u
*L3461
21
10u
*L2461
10u
*L2462
NQR0559-009X
*K2101
1
*C2361
0.01
*C2163
0.1
*C2363
*C2465
0.01
*C2264
1
*C3761
*C3461
10
*C2462
1
*C2166
1
*C2662
1
*C2165
10
*C2463
0.015
*C2162
1
*C2661
OPEN
*C2362
0.015
*C2161
0.01
*C2164
0.01
*C2263
*C2464
5
MUTEOUTL
A5
34
MICINR2
E7
3
SPIN
A3
22
VIN
D2
39
CSB
F5
25
NC
D5
2
SPVSS
A2
20
MICINL1
C7
29
ADOUT
E2
46
SCLK
G5
38
MCLKO
F4
40
DMDAT
F6
7
AVSS
A7
1
SPPOS
A1
BU76312GUW-X
*IC2061
26
MREGL
D6
12
BIAS
B6
35
LRCLK
F1
48
LNFR
G7
32
NC
E5
41
MICINR1
F7
11
LINEOUTR
B5
15
VVDD
C2
14
VOUT
C1
8
SPVDD
B2
16
NC
C3
23
PDB
D3
30
TEST
E3
37
BCLK
F3
18
NC
C5
9
SPNEG
B3
44
IOVDD
G3
28
DAIN
E1
10
LINEOUTL
B4
47
DMCLK
G6
36
MCLK
F2
45
SDATA
G4
4
EVROUT
A4
27
LNFL
D7
33
MREGR
E6
6
MUTEOUTR
A6
13
AVDD
B7
43
DVSS
G2
31
NC
E4
42
DVDD
G1
24
NC
D4
19
MICINL2
C6
17
BEEPIN
C4
21
VVSS
D1
<MAIN(AUDIO(STEREO)) SCHEMATIC DIAGRAM> [STEREO TYPE ONLY]
Note : The parts numbers in the schematic diagram are for references only.
When replacing the parts, refer to the PARTS LIST.
10
0
1
MAIN(AUDIO(MONO))
yf362_y10890001a9/9_1124_ver0.1
from REG
from ROHM
to IF
from ROHM (IC2061)
from/to Felix
to IF
AU_SIG/LM
AIBD
AU_SIG/R
V_OUT
SPK-
SPK+
GND
AUDIO_CLK
AIOBCK
AUDIO_OUT
GND
SYIN
AOBD
REG_2.8V
INT_LM
AUDIO_CS
AOMCLK
AIOLRCK
AVDD
*TL2301
10
*R2204
0
R2255
ǡ
*R2803
OPEN
*R2253
_0.5%
180
*R2251
470
*R2802
10
R2404
OPEN
*R2405
330k
*R2801
2.2k
*R2131
75
*R2200
10
*R2203
OPEN
L2251
10u
*L2402
EXPOSED PAD29
MICP28
MICN27
VMID26
AUX25
SPKVDD24
SPKROUTN23
SPKGND22
SPKROUTP
21
MONOOUT
20
VBIN
19
VBREF
18
VBOUT17VBVDD
16
SDIN
15
SCLK 14
MODE/GPIO 13
CSB/GPIO 12
MCLK 11
BCLK 10
FRAME 9
DACDAT 8
ADCDAT
7
DGND
6
DBVDD5DCVDD
4
AGND3AVDD
2
MICBIAS
1
WM8941GEFL/V-W
*IC2201
OPEN
*C2401
4.7
*C2602
/6.34.7
*C2251
OPEN
*C2601
OPEN
C2252
1
*C2603
OPEN
*C2404
0.0047
*C2605
1
*C2801
OPEN
*C2402
0.01
*C2604
<MAIN(AUDIO(MONO)) SCHEMATIC DIAGRAM> [MONO TYPE ONLY]
Note : The parts numbers in the schematic diagram are for references only.
When replacing the parts, refer to the PARTS LIST.
11
yf362_y20523001a_1124_ver0.1
0
2
REAR
INFO
OK
INTELLIGENT AUTO
PLAYBACK
CAMERA/VIDEO USER
SONY GYRO
REDGREEN
[-]
[T]
[+]
[D]
[-]
GND
KEY_A
Y_GYRO_IN
P_GYRO_IN
PWR_LED
REG_2.8V
AL_2.8V
ACES_LED
AL_2.8V
PWR_LED
ACES_LED
Y_GYRO_IN
P_GYRO_IN
KEY_A
REG_2.8V
BATT_L
P_DET
V_OUT
AU_SIG/R
AU_SIG/L
G_RESET
D_BATT
T_BATT
D_BATT
BATT_L
T_BATT
V_OUT
G_RESET
AU_SIG/L
P_DET
AU_SIG/R
REG_2.8V
GND
21
NSW0323-001X
S694
21
NSW0323-001X
S691
21
NSW0323-001X
S693
21
NSW0323-001X
S692
OPEN
R914
OPEN
R609
6.8k
R693
15k
R694
47k
R695
2.2k
R906
2.2k
R911
OPEN
R903
100k
R908
470
R610
NRSA6AJ-0R0W
L601
100R601
OPEN
R902
100R602
OPEN
R910
100k
R916
21
L602
NQR0645-001X
21
L603
NQR0645-001X
NQR0599-003X
K901
54321
BATTERY TERMINAL
BT601
QNA0060-001
5
4
3
2
1
DC JACK
J602
QNA0059-001X
5
4
3
2
1
AV JACK
QNS0297-001X
J601
VIN
4
VOUT3VSS
2
CE
1
XC6215B332NG-X
IC601
21
NMFZ028-2R5X-J1
F601
21
NMFZ028-2R5X-J1
F602
21
D611
LNJ326W83-X
21
D612
SML-D12V8W/PQ-X
2
1
D601
DZ2J068/M/-X
2
1
D605
DZ2J068/M/-X
2
1
OPEN
D602
DZ2J068/M/-X
2
1
OPEN
D603
DZ2J068/M/-X
2
1
D604
DZ2J068/M/-X
2
1
OPEN
D610
DZ2J068/M/-X
2
1
DB22320-X
D609
DB2J314-X
D606
ACES_LED1
PWR_LED2
AL_2.83V3
GND4
KEY_A5
BATT_L6
D_BATT7
T_BATT8
LI_CHRG9
BATT+10
BATT+11
BATT+12
BATT+13
BATT+14
BATT+15
BATT+16
BATT+17
ADP_DC18
ADP_DC19
ADP_DC20
ADP_DC21
ADP_DC22
Y_GYRO_IN23
P_GYRO_IN24
REG_2.83V25
G_RESET26
GND27
GND28
GND29
GND30
GND31
GND32
GND33
GND34
LITHIUM35
AU_SIG/R36
AU_SIG/L37
GND38
V_OUT39
P_DET40
TO MAIN PWB
CN601
QGF0528F4-40X
OPEN
C604
0.001
C601
OPEN
C611
1C609
0.1
C908
0.0047
C913
NCBA1AK-104W
C607
OPEN
C608
0.0047
C904
0.001
C602
OPEN
C603
0.1
C911
0.01
C910
OPEN
C606
0.047
C906
0.047
C902
0.01
C901
22
C918
22
C907
1C610
1
C916
1
C915
QAB0041-001
LITHIUM BATTERY
QAB0040-001
BT602
APX
20
NC
25
APY
23
FY
18
ANX
3
AOX9AOY10NC12F2Y
11
ANY
4
NC
26
F2X
8
NC
1
IC901
NAL0094-001X
NC28NC27NC
24
F1Y
5
VREF
22
FOY
17
CRS
16
F1X
2
GND
15
NC
19
NC
6
NC
7
VCC
21
FX13FOX
14
<REAR SCHEMATIC DIAGRAM>
Note : The parts numbers in the schematic diagram are for references only.
When replacing the parts, refer to the PARTS LIST.
12
yf362_y30479001a_1124_ver0.1
0
3
JACK
!
NO USB HOST
USB HOST
TO MAIN PWB
TO MAIN PWB
HDMI
USB
MULTI
TMDS_D0+
TMDS_REG5V
HDMI_SDA
HDMI_SCL
HDMI_CEC
TMDS_CLK-
HDMI_SDA
DTRM_PR
USBDP
TMDS_CLK+
TMDS_REG5V
MENU/PWR_SW
HDMI_SCL
DTRM_Y
TMDS_D0-
TMDS_D0+
DTRM_PB
XUSBHOST
HDMI_CEC
D_DET_L
TMDS_D1-
USBDN
TMDS_D1+
MENU/PWR_SW
TMDS_D2-
TMDS_D2+
GND
VBUS
TMDS_D1+
TMDS_D2-
TMDS_D1-
TMDS_CLK-
TMDS_D0-
TMDS_D2+
TMDS_CLK+
DTRM_PB
USBDP
USBDN
GND
GND
XUSBHOST
D_DET_L
GND
GND
GND
DTRM_Y
HDMI_PDET
VBUS
DTRM_PR
HDMI_PDET
21
PWR_SW
PLAY/REC
NSW0323-001X
S201
23
2221
20
Hot Plug Detect
19
+5V Power
18
NC
17
SDA
16
SCL
15
CEC
14
GND
13
TMDS Clock-
12
TMDS Clock+
11
GND
10
TMDS Data0-
9
TMDS Data0+
8
GND
7
TMDS Data1-
6
TMDS Data1+
5
GND
4
TMDS Data2-
3
TMDS Data2+
2
GND
1
*J201
NNZ0212-001X
16
1514
13
GND
12
D_DET
11
Pb
10
GND_Y
9
NC
8
Pr
7
LINE_3
6
GND_Pb/Pr
5
Y
4
NC
3
LINE_1
2
LINE_2
1
*J202
NNZ0224-001X
9
87
6
54321
NNZ0251-001X
*J203
NNZ0246-001X
21
NMFZ028-2R5X-J1
F201
2
1
OPEN
D201
DZ2J068/M/-X
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
*CN202
QGF0543F3-24X
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
*CN201
QGF0543F3-18X
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
*CN203
QGF0543F3-15X
<JACK SCHEMATIC DIAGRAM>
Note : The parts numbers in the schematic diagram are for references only.
When replacing the parts, refer to the PARTS LIST.
13
yf362_y20524001a_1124_ver0.1
0
4
MONITOR
MR SENSOR
LCD BACKLIGHT
From Main PWB
From Felix
From Felix
To Touch panel unit
To 2.7' LCD
TOUCH PANEL IF
To Felix
TP_X
TP_Y
TP_SEL2
TP_X
VDDE_2.8V
REG_2.8V
GND
TP_SEL1
TP_Y
REG_2.8V
VDDE_2.8V
REG_2.8V
TP_SEL2
GND
TP_SEL1
OPEN
R724
OPEN
R723
OPEN
R725
100k
*R742
OPEN
R703
OPEN
ǡ
*R748
OPEN
ǡ
*R750
OPEN
ǡ
*R749
OPEN
ǡ
*R747
OPEN
ǡ
*R746
OPEN
ǡ
*R745
OPEN
ǡ
*R744
OPEN
ǡ
*R743
OPEN
R704
OPEN
R722
OPEN
*R741
OPEN
R702
OPEN
R726
OPEN
R720
OPEN
R730
220k
R701
ǡ
R729
OPEN
R721
OPEN
R705
ǡ
R728
ǡ
R727
654
321
OPEN
UMX1N-W
Q721
654
321
OPEN
UMX1N-W
Q722
RT1N432U-X
*Q745
RT1N432U-X
*Q744
3
2
1
*Q743
RT1P432U-X
3
2
1
*Q742
RT1P432U-X
3
2
1
*Q741
RT1P432U-X
OPEN
L702
OPEN
*L741
OPEN
L723
OPEN
L701
OUT
4
VDD3GND
2
NC
1
HGDESN031A-X
IC722
VOUT
5
NC4ON/OFF
3
VSS
2
VIN
1
OPEN
IC721
109876
54321
OPEN
D703
109876
54321
OPEN
D704
54
321
OPEN
*D741
NSSW006/T294-X
D721
NSSW006/T294-X
D723
NSSW006/T294-X
D722
OPEN
D724
2
1
OPEN
D701
2
1
OPEN
D705
2
1
OPEN
D702
LCD_DATA39
LCD_CLK38
LCD_CS37
LCD_RST36
LCD_HD035
LCD_VD034
LCD_CLK033
GND32
LCD_GO_731
LCD_GO_630
LCD_GO_529
LCD_GO_428
LCD_GO_327
LCD_GO_226
LCD_GO_125
LCD_GO_024
VDDI_1.8V23
NC22
VDD_2.8V21
VCORE_1.8V20
GND19
VSH18
CP1B17
CP1A16
VOUT15
CP2B14
CP2A13
CP3B12
CP3A11
VGH10
CP4B9
CP4A8
VGL7
GND6
CP5B5
CP5A4
VCOML3
VCL2
VCOMH1
CN702
QGF0319F1-39X
34
33
GND 32
TP_Y 31
TP_X 30
TP_SEL2 29
TP_SEL1 28
TP_VDD 27
GND 26
LCD_GO_0 25
LCD_GO_1 24
LCD_GO_2 23
LCD_GO_3 22
LCD_GO_4 21
LCD_GO_5 20
LCD_GO_6 19
LCD_GO_7 18
GND 17
LCD_CLK0 16
GND 15
GND 14
LCD_VD0 13
LCD_HD0 12
REG_2.8V 11
REG_1.8V 10
LCD_RST 9
LCD_CS 8
LCD_CLK 7
LCD_DATA 6
GND 5
M_RVS 4
BL_CTL1/BL_FBI 3
REG_LED/REG_5.0V 2
REG_LED/REG_5.0V 1
CN701
QGF0528F4-34X
8
7
6
5
4
3
2
1
QGF0528F4-08X
*CN703
2
1
C707
1
2
1
C705
1
1
C704
OPEN
C724
2.2C706
2.2C714
OPEN
1
C701
1
C711
OPEN
1
C702
1
C708
1
C721
0.0047
*C743
1
C710
OPEN
*C741
2.2
C713
OPEN
0.0047
*C744
OPEN
0.0047
*C745
0.0047
*C742
OPEN
1
C703
OPEN
C722
2.2C716
2.2
C715
1
C709
OPEN
C723
1
C712
<MONITOR SCHEMATIC DIAGRAM>
Note : The parts numbers in the schematic diagram are for references only.
When replacing the parts, refer to the PARTS LIST.
14
yf362_y10900001a_1124_ver0.1
0
5
CMOS
1
CMOS SENSOR IMX102
To CONNECTOR
Digital Output
Digital Power & GND
Analog Output
Analog Power & GND
INCK
XCLR
DOBM
DOBP
DOAM
DOAP
DCKM
DCKP
DOBM
DOBP
DOAM
DOAP
SCK
XHS
XVS
XCE
SDI
XCLR
SCK
XCE
SDI
XVS
XHS
INCK
DCKP
DCKM
VDD4OUTPUT
3
CASE GND
2
ENABLE/DISABLE
1
X451
NAX1018-001X
OPEN
R452
OPEN
R458
ǡ
R457
OPEN
R451
OPEN
R453
47k
R454
10u
NQL382M-100X
L451
21
L452
NQR0286-006X
21
OPEN
L453
NQR0286-006X
VCC
5
OUT Y
4
GND3IN A2NC
1
OPEN
TC7SG34FU-X
IC452
GND24
CAM_1.8V
23
CAM_1.8V
22
CAM_2.7V
21
CAM_2.7V
20
GND
19
CMOS_RST
18
CMOS_CLK
17
CMOS_CS
16
CMOS_OUT
15
VD_CMOS
14
HD_CMOS
13
GND
12
CLK_IN11
GND10
DCKP_A9
DCKM_A8
GND7
DOP3_A6
DOM3_A5
GND4
DOP2_A3
DOM2_A2
GND1
CN451
QGF0534F5-24X
2
1
OPEN
C457
2
1
OPEN
C458
OPEN
C460
OPEN
C461
2.2C471
OPEN
C459
0.1
C456
10
C451
OPEN
C466
10
C452
OPEN
C453
OPEN
C465
0.1C472
OPEN
C468
OPEN
C467
OPEN
C469
OPEN
C462
OPEN
C464
2.2
C473
OPEN
C470
OPEN
C463
OPEN
C455
0.1C454
67
NC
J7
54
NC
H3
74
VDDLIO
K5
61
NC
J1
13
NC
B5
35
VSSLCN1
E2
72
NC
K3
11
NC
B2
10
NC
B1
9
NC
A9
28
VDDHCP
D1
7
VDDHVS
A7
76
VDDSUB2
K7
3
VDDSUB1
A3
5
VDDHPX
A5
27
VDDHDA
C9
46
VDDHCM1
G1
39
VDDHCM2
E9
34
VSSHCP
E1
6
VSSHVS
A6
45
NC
F9
40
NC
F1
33
VSSHDA
D9
4
VSSHPX
A4
2
NC
A2
1
NC
A1
IC451
IMX102CQK-C
71
NC
K2
70
NC
K1
18
NC
B9
69
TEST4
J9
44
XHS
F8
51
XVS
G9
37
SDI
E7
16
XCE
B7
38
SCK
E8
24
XCLR
C6
52
INCK
H1
60
TEST3
H9
12
VRL
B3
17
NC
B8
78
NC
K9
48
VDDHPL
G3
56
DCKP
H5
68
NC
J8
59
NC
H8
49
VDDLSC2
G7
58
NC
H7
66
DOBM
J6
57
DOBP
H6
64
DOAM
J4
55
DOAP
H4
63
NC
J3
75
VSSLIO
K6
62
NC
J2
53
NC
H2
77
TEST5
K8
65
DCKM
J5
43
SDO
F7
22
TEST2
C4
8
TEST1
A8
23
NC
C5
19
NC
C1
20
VCP
C2
21
VBGR
C3
15
VEXRES
B6
13
VLOADLM
B4
26
VDDLCN2
C8
42
VDDLSC1
F3
25
NC
C7
32
VSSLCN2
D8
31
NC
D7
36
VDDLCN1
E3
47
VSSHPL
G2
73
NC
K4
41
VSSLSC1
F2
30
NC
D3
50
VSSLSC2
G8
29
NC
D2
<CMOS SCHEMATIC DIAGRAM>
Notes : 1. The parts number in the schematic diagram are for references only.
When replacing the parts, refer to the PARTS LIST.
2.
The schematic diagram is only for reference. Avoid replacing individual parts.
Replace the entire unit only.
When CMOS BOARD ASSEMBLY needs replacement, replace the CMOS FRAME ASSEMBLY in whole because it cannot be replaced alone.
15
TL3213
TL3035
TL2301
TL1030
TL1029
RA9006 RA9005
RA9002
RA9001
RA8004RA8003
RA8002RA8001
RA3010
RA3008
RA3007
RA3006
RA3005
RA3004
R9045
R9042
R9041
R9040
R9039
R9038
R9037
R9036
R9035
R9034
R9033
R9032
R9031
R9030
R9029
R9028
R9027
R9026
R9025
R9024
R9023
R9022
R9021
R9020
R9019
R9018
R9017
R9016
R9015
R9014
R9013
R9012
R9011
R9010
R9007
R9006
R9005
R9004 R9003
R9002
R9001
R8012
R8010
R8001
R4680
R3246
R3205R3203R3202
R3137
R3103
R3101
R3098
R3096
R3095
R3094
R3077
R3068
R3067
R3058
R2803R2802
R2801
R2664
R2663
R2662
R2661
R2464
R2405
R2404
R2255
R2253
R2251
R2204
R2203
R2200
R2131
Q9001
Q4602
Q2662
Q2661
LC3005
L9002
L8055
L2402
L2251
K3007
K3004
K3002
K3001
IC8002
IC8001
IC3201
IC2201
IC2061
DA9003
DA9002
DA9001
D9006
D9005
D9003
D9002
D9001
CN9012
CN9010
CN9009
CN9007
CN9006
CN9003
CN9002
CN9001
CN8001
C9016
C9015
C9014
C9013
C9012
C9011
C9010
C9009
C9008
C9007
C9006
C9005
C9004
C9003
C9002
C9001
C8014
C8011
C8008
C8007
C8004
C8003
C3761
C3461
C3202
C3071
C3070
C3069
C3068
C3067
C3066
C3065
C3064
C3063
C3062
C3056
C3055
C3049
C3046
C3045
C3030
C3029
C3025
C3022
C3021
C3020
C3019
C3018
C3017
C3016
C2801
C2662
C2661
C2605
C2604
C2603
C2602
C2601
C2465
C2464
C2404
C2402
C2401
C2363
C2362
C2361
C2264
C2263
C2252
C2251
C2166
C2165
C2164
C2163
(Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade))
LYB10258-001B
FOIL SIDE(B)
<01>MAIN
<MAIN CIRCUIT BOARD>
16
PbF
X3001
X1001
TP9002
TP9001
TH9001
RA3011
RA3009
RA3003RA3002
RA1004
RA1003
RA1002
RA1001
R9044
R9043
R6924
R6922
R6921
R6916
R6913
R6912
R6911
R6908
R6907
R6905
R6903
R6902
R6901
R6604
R6603
R6602
R6601
R6504
R6503
R6502
R6501
R6403
R6402
R6303
R6302
R6301
R6203
R6202
R6201
R6109
R6108
R6104
R6103
R6102
R6101
R6005
R6004
R6003
R6002
R6001
R4609
R4608
R4607
R4606
R3704
R3703
R3702
R3701
R3509R3508
R3507 R3506
R3505
R3504R3503
R3502
R3501
R3303
R3302
R3301
R3138
R3136
R3135
R3134
R3133
R3132
R3131
R3130
R3129
R3128
R3127
R3100
R3097
R3093
R3092
R3091
R3090
R3089
R3088
R3087
R3086
R3085
R3084
R3083
R3082
R3081
R3080
R3079
R3078
R3076
R3075
R3074
R3073
R3072
R3071
R3070
R3069
R3065
R3064
R3063
R3062
R3061
R3060
R3059
R3057
R3056
R3055
R3054
R3053
R3052
R3048
R3042
R3040
R3039
R3038
R3037
R3036
R3035
R3034
R3033
R3032
R3031
R3030
R3029
R3028
R3027
R3025
R3024
R3023
R3022
R3021
R3020 R3019
R3018
R3017
R3015
R3014
R3013
R3012
R3011
R3010
R3008
R3007
R3006
R3005
R3004
R3003
R3002
R3001
R2463 R2462
R2162
R2161
R1093
R1092
R1091
R1090
R1069
R1068
R1064
R1063
R1062
R1061
R1053
R1048
R1047
R1046
R1045
R1036
R1035
R1034
R1032
R1031
R1030
R1029
R1028
R1027
R1026
R1025
R1024
R1023
R1022
R1018
R1017
R1014
R1013
R1012
R1011
R1006
R1005
R1002
Q6908
Q6907
Q6906
Q6904
Q6903
Q6901
Q6401
Q6301
Q6105
Q6102
Q6101
Q4502
Q3005
Q3004
Q3003
Q3002
Q3001
Q2462
LC3001
L9001
L6601
L6501
L6401
L6301
L6201
L6101
L4601
L3701
L3461
L3002
L3001
L2462
L2461
K3009
K3008
K3006
K3005
K2103
K2102
K2101
IC6004
IC6003
IC6002
IC6001
IC4601
IC3701
IC3202
IC3101
IC3011
IC3010
IC3004
IC3003
IC3002
IC3001
IC1006
IC1004
IC1003
IC1001
D6901
D6601
D6101
CN9014
CN9013
CN9011
CN9008
CN9005CN9004
CN4602
C9017
C6910
C6909
C6908
C6907
C6906
C6905
C6904
C6903
C6901
C6604
C6603
C6602
C6601
C6504
C6503
C6502
C6501
C6403
C6402
C6401
C6306
C6305
C6304
C6303
C6302
C6301
C6204
C6203
C6202
C6201
C6108
C6107
C6106
C6105
C6104
C6103
C6102
C6101
C6009
C6001
C4604
C4601
C3708
C3707
C3706
C3705
C3704
C3703
C3702
C3701
C3201
C3104
C3103
C3102
C3101
C3076
C3075
C3074
C3073
C3072
C3061
C3060
C3059
C3058
C3054
C3053
C3052
C3051
C3050
C3048
C3047
C3043
C3042
C3041
C3038
C3037
C3036
C3035
C3034
C3033
C3032
C3031
C3028
C3026
C3024
C3023
C3015
C3014
C3013
C3012
C3011
C3009 C3008
C3007
C3006
C3005
C3004
C3003
C3002
C3001
C2463
C2462
C2162
C2161
C1021
C1020
C1019
C1012
C1011
C1010
C1009
C1006
C1005
C1004
C1003
C1002
C1001
10258
LYA
AY
MAIN
PWB
(Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade))
LYB10258-001B
COMPONENT SIDE(A)
<01>MAIN
<MAIN CIRCUIT BOARD>
<REAR CIRCUIT BOARD>
(Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade))
CAUTION :
<02>REAR
LYB20080-001B
FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH SAME TYPE AND RATED FUSE(S).
ATTENTION :
POUR UNE PROTECTION PERMANENTE CONTRE LES RISQUE D'INCENDE,
!
REMPLACER LES FUSIBLES PAR UNAAUTRE DE MEME TYPE ET DE MEME TENSION.
J602
CN601
FOIL SIDE(B)
+
R916
R903
C913
R910
C911
C901
C902
R902
C918
BT602
LYA
20080
-01B
D601
1
COMPONENT SIDE(A)
D611
C611
S691
R693
D605
REAR PWB
R911
R908
C904
C910
C908
IC901
C907
R914
R906
C915
K901
C916
L601
J601
C906
ASS'Y
S693
S692
S694
C607
D603
D604
F602
F602
D602
C601
R602
C603
L603
C608
PbFPbF
C602
D612
F601
F601
R609
D609
D610
C606
ULMARK
PCB
C604
L602
R601
AOI
0
C609
IC601
R610
C610
D606
2
<JACK CIRCUIT BOARD>
(Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade))
CAUTION :
<03>JACK
LYB20080-001B
FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH SAME TYPE AND RATED FUSE(S).
ATTENTION :
POUR UNE PROTECTION PERMANENTE CONTRE LES RISQUE D'INCENDE,
!
REMPLACER LES FUSIBLES PAR UNAAUTRE DE MEME TYPE ET DE MEME TENSION.
FOIL SIDE(B)
PbFPbF
0
AOI
3
PCB
ULMARK
COMPONENT SIDE(A)
S201
J201
CN201
JACK PWB ASS'Y
J203
3
CN203
LYA20080-01B
J202
D201
F201
F201
CN202
17
<MONITOR CIRCUIT BOARD>
(Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade))
<04>MONITOR
LYB20080-001B
D721
D722
D723
IC722
R705
R704
R703
CN701
R741
Q742
MONI PWB ASS'Y
FOIL SIDE(B)
COMPONENT SIDE(A)
R750
R749
R748
R747
R746
R745
R744
R743
C721
L701
R730
C722
L723
C724
D724
D705
L702
IC721
C723
D702
C702
C701
D701
PbFPbF
UL MARK
D704 D703
C744
Q744
C743
Q741
D741
Q745
C745
R742
C742
R723
Q721
L741
Q743
C741
LYA20080-01B
R721
R720
R724
CN703
R725
C703
4
0
Q722
R729
R722
R727
R728
R702
C716
C714
C711
C710
C713
C708
R701
R726
CN702
C715
C712
C709
C706
C704
C707
C705
PCB
AOI
2
<CMOS CIRCUIT BOARD>
(Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade))
<05>CMOS
LYB20082-001A
PbF
The Circuit board is only for reference. Avoid replacing individual parts.
Replace the entire unit only. When CMOS BOARD ASSEMBLY needs replacement,
replace the CMOS FRAME ASSEMBLY in whole because it cannot be replaced alone.
FOIL SIDE(B)COMPONENT SIDE(A)
IC451
CN451
R451
R453
X451
C454
C455
C473
C467
C469
L453
L452
R457
L451
R452
IC452
C470
C463
C472
C471
R454
C453
C452
C451
C462
C458
C460
C457
C461
C466
C465
C459
C464
C456
C468
18
Victor Company of Japan, Limited
Imaging Products Business Division 12, 3-chome, Moriya-cho, Kanagawa-ku, Yokohama-city, Kanagawa-prefecture, 221-8528, Japan
(No.YF365<Rev.001>)
Printed in Japan
VSE
PARTS LIST
12
CAMCORDER
GZ-HM30BKRGZ-HM30BUAGZ-HM30BUB
(No.YF365<Rev.001>)1/
■ PRECAUTIONS ON SCHEMATIC DIAGRAMS
z Due to the improvement in performance, some part numbers shown in the circuit diagrams
may not agree with those indicated in the Parts List.
z The parts numbers, values and rated voltage etc. in the Schematic Diagrams are for
reference only.
z Since the circuit diagrams are standard ones, the circuits and circuit constants may be
subject to change for improvement without any notice.
■ PRECAUTIONS ON PARTS LIST
z
The parts identified by the symbol are critical for safety. Whenever replacing these parts, be sure to
use specified ones to secure the safety.
z
The parts not indicated in this Parts List and those which are filled with lines --- in the Parts No.
columns will not be supplied.
z
P.W. BOARD Ass'y will not be supplied, but those which are filled with the Parts No. in the Parts No.
columns will be supplied.
z
When ordering chips, screws etc., place bulk orders (unit of tens) whenever possible to improve
shipping efficiency.
z
There are cases where the actual implemented parts in the sets and the service parts are different.
When ordering parts, make sure to refer to the Parts List.
■
PRECAUTIONS ON SERVICE
Certain parts of the power circuits and the GNDs differ according to the models. Care must be
taken for the following points as the differences are indicated separately in the LIVE GND () and
the ISOLATED (NEUTRAL) GND ().
1.Do not touch the LIVE GND, or do not touch the LIVE GND and the ISOLATED (NEUTRAL)
GND at the same time. It may cause an electric shock.
Before pulling out the chassis or other parts, make sure to pull out the power cord from the
wall outlet first.
2.Do not short circuit between the LIVE GND and ISOLATED (NEUTRAL) GND, or never
measure the LIVE GND and ISOLATED (NEUTRAL) GND at the same time using measuring
instruments (oscilloscope, etc.). It may blow fuses or damage other parts.
■ DEVIATION TOLERANCE RANGE
DEVIATION TOLERANCE RANGE
F G J K M N R H Z P
± 1% ± 2% ± 5% ±10% ±20% ±30%
+30%
-10%
+50%
-10%
+80%
-20%
+100%
-0%
12
(No.YF365<Rev.001>)2/
229
227
226
226
225
223
216
215
214
211
DC
210B
210A
210
107
105
105
104
103
102
101
C
B
A
FINAL ASSEMBLY<M1>
The instruction manual to be provided with this product will differ according to the destination.
MODEL
MARK
GZ-HM30BUB
GZ-HM30BKR
GZ-HM30BUA
created date:2011-02-10No.YF365
12
(No.YF365<Rev.001>)3/
507
507
507
506
506
506
503
502
501
499
403
228
224
224
222
220
220
219
218
217
217
213
212
208
207
206
205
204
203
202
201
GZ-HM30BUA
GZ-HM30BKR
GZ-HM30BUB
MARK
MODEL
A
B
C
The instruction manual to be provided with this product will differ according to the destination.
FINAL ASSEMBLY<M1>
BASE
FRONT ASSEMBLY
<02>
ASSEMBLY
REAR BOARD
CMOS BOARD
ASSEMBLY
<05>
<01>
ASSEMBLY
MAIN BOARD
UPPER ASSEMBLY
OP BLOCK
created date:2011-02-10No.YF365
12
(No.YF365<Rev.001>)4/
329
328
328
327
327
326
326
325
324
323
323
322
322
321
320
319
318
317
316
315
314
313
312
311
310
309
308
307
305
304
303
302
301
GZ-HM30BUA
GZ-HM30BKR
GZ-HM30BUB
MARK
MODEL
A
B
C
The instruction manual to be provided with this product will differ according to the destination.
FINAL ASSEMBLY<M1>
JACK BOARD
ASSEMBLY
<03>
MONI. BOARD ASSEMBLY
UPPER ASSEMBLY
<04>
created date:2011-02-10No.YF365
12
(No.YF365<Rev.001>)5/
MODELMARKMODELMARKMODELMARK
12
GZ-HM30BKRAGZ-HM30BUABGZ-HM30BUBC
Safe Symbol No. Parts No.Parts NameDescriptionQTYLocal
FINAL ASSEMBLY <M1MM>
101LY37600-001CTOP COVER ASSY 1
102------------STICKER 1 A
102------------STICKER 1 B,C
!103LY37969-032ARATING LABEL A 1 A
!103LY37776-003ARATING LABELA-LP 1 B
!103LY37778-003ARATING LABELA-LP 1 C
104LY30031-0R3ASPECIAL SCREWTOP-REAR 1
105LY30031-0R2ASPECIAL SCREWLOWER-BKT LOWER 2
107------------REAR LABEL A 1 A
107------------REAR LABELA-LP 1 B
107------------REAR LABELA-LP 1 C
201LY37584-001DREAR COVER ASSY 1 A
201LY37584-001CREAR COVER ASSY 1 B,C
202WJT0267-001A-EE-CARD WIREREAR P-MAIN 1
203------------SHIELD(MAIN) 1
204LY22199-001AOPE UNIT 1
205LY22208-009CF.COVER ASY C1A 1
206QAN0112-001MICROPHONE UNIT 1
207------------PLATE (MIC) 1
208LY22191-001ASHUTTER ASSY 1
210LY37597-001DL.CASE ASY CIAInc.210A-B 1
210ALY37593-001BGRIP BELT 1
210BLY37639-001BDC CVR JACK C1A 1
211LY37627-001BWINDOW (WB) 1
212LY30031-0R2ASPECIAL SCREWSHLD-BKT HINGE 1
213LY30031-0R3ASPECIAL SCREWSHLD-T.HOL 1
214LY30031-0R3ASPECIAL SCREWREAR-UPPER 1
215LY30031-0R2ASPECIAL SCREWREAR-SHLD 1
216LY30031-0R3ASPECIAL SCREWUPPER-T.HOLDER R 1
217LY30031-0R2ASPECIAL SCREWM.PWB - SHLD MAIN 2
218LY30031-0R1ASPECIAL SCREWOPE-UPPER 1
219LY30031-0R1ASPECIAL SCREWP.MIC-FRONT 1
220LY30031-0R1ASPECIAL SCREWSHUTTER-FRONT 2
222LY30031-0R2ASPECIAL SCREWFRONT-BKT HINGE 1
223LY30031-0R3ASPECIAL SCREWUPPER-T.HOLDER F 1
224LY30031-0R3ASPECIAL SCREWUPPER-FRONT 2
225LY30031-0R2ASPECIAL SCREWBKT LOWER-SHLD 1
226LY30031-0R3ASPECIAL SCREWLOWER-T.HOLDER 2
227LY30031-0R1ASPECIAL SCREWREAR-LOWER 1
228LY30031-0R1ASPECIAL SCREWLOWER-REAR 1
229LY30031-0R2ASPECIAL SCREWWIN WB-SHLD 1
301LY21558-005AHINGE UNIT 1
302QAL1321-002FPCMONI-MAIN 1
303LY37617-001AH COVER (L) 1
304------------P.C.MAGNET 1
305LY37616-001BH COVER (U) CIA 1 A
305LY37616-001AH COVER (U) CIA 1 B,C
307LY37605-001BM.CASE ASY CIA 1
308QLD0670-001LCD MODULE 1
309LY37606-001ASHEET CLEARANCE 1
310LY37607-001ASHEET BEF(MAIN) 1
311LY37620-001ASHEET BEF(SUB) 1
312LY37608-001ASHEET (M.DIFF) 1
313LY37609-001ALIGHT GUIDE 1
314LY37610-001ASHEET (M.REF) 1
315LY37614-005BM COVER ASY CIA 1 A
315LY37614-005AM COVER ASY CIA 1 B,C
316LY37621-001DU.FRAME ASSY 1 A
316LY37621-002DU.FRAME ASSY 1 B,C
317QAS0619-001SPEAKER 1
318------------BKT(SPK) 1
319WJT0266-001A-EE-CARD WIRE24P JACKS 1 A
319WJT0265-001A-EE-CARD WIRE24P JACKS 1 B,C
320WJT0264-001A-EE-CARD WIRE18P HDMI F 1
321LY37611-001BT.BASE ASSY 1
322LY30031-0R1ASPECIAL SCREWM.PWB-M.CASE 2
323LY30031-0N5ASPECIAL SCREWM.COVER-HI 2
324LY30031-0H5ASPECIAL SCREWBKT SPK-BKT HINGE 1
325LY30031-0H5ASPECIAL SCREWJ.PWB-J.PLATE 1
326LY30031-0Q7ASPECIAL SCREWUPPER-T.HOLDER 2
327LY30031-0Q5ASPECIAL SCREWHINGE-BKT 2
328LY30031-0H5ASPECIAL SCREWMONI FPC-BKT HINGE 2
329------------SPACER(A) 1
403QAL1322-001FPC 1
499LYA20082-01ACMOS FRAME ASSYCMOS BOARD
501LY37655-001AOP BLOCK 1
502------------IR CUT FILTER 1
503------------SHEET 1
506------------TAP SCREWM1.7 x 5mm 3
507LY30032-037ASPECIAL SCREWUPPER-OP 3
ASSY(INCL.BASE/FPC)
1
(No.YF365<Rev.001>)6/
822
803
802
710
709
708
707
706
705
704
703
702
701
GZ-HM30BUA
GZ-HM30BKR
GZ-HM30BUB
MARKMODEL
A
B
C
PACKING AND ACCESSORY ASSEMBLY <M5>
FINAL ASSEMBLY
<M1>
created date:2011-02-10No.YF365
12
(No.YF365<Rev.001>)7/
MODELMARKMODELMARKMODELMARK
12
GZ-HM30BKRAGZ-HM30BUABGZ-HM30BUBC
Safe Symbol No. Parts No.Parts NameDescriptionQTYLocal
PACKING AND ACCESSORY ASSEMBLY <M5MM>
701------------POLY BAGFOR JMM 1 A,B
701------------POLY BAG 1 C
702------------PACKING CASEPRODUCTION 1 A
702------------PACKING CASEA-LP 1 B
702------------PACKING CASEPRODUCTION 1 C
703------------CUSHION 1 A,C
703------------CUSHION 1 B
704------------LABEL 1 A,B
705------------LABEL(COLOR)FOR P.CASE 1 A
706QAM1293-001A/V CABLE 1
707QAM1313-001USB CABLE(TYPE A-MINI TYPE B) 1
!708QAL1318-001AC P ADAPTORAC-V10M 1
!709LY37166-006ABATTERY PACKBN-VG107KR 1 A
!709LY37166-003CBATTERY PACKBN-VG107E 1 B,C
!710QMPS560-100-JRPOWER CORD1m BLACK 1 A
!710QMPS580-100-JRPOWER CORD1m BLACK 1 B
!710QMPS590-100-JRPOWER CORD1m BLACK 1 C
802LY37342-025A-S1CD ROM ASSY 1
!803LYT2309-001A-MINST BOOK(KOREAN) 1 A
!803LYT2285-001AINST BOOK(SPANISH) 1 B
!803LYT2286-001AINST BOOK(PORTUGUESE) 1 C
822------------SHEET ACC. GUIDLY37669-003A 1 A
822------------SHEET ACC. GUIDLY37669-004A 1 B
MAIN BOARD ASSEMBLY <01>
PW1001LYA10258-11CMAIN BOARD ASSY 1 A
PW1001LYA10258-10BMAIN BOARD ASSY 1 B,C
IC1001M395FWAXG7GG1-XIC(MICRO C ROM)AP/MP FLASH 1
IC1003R1EX25004ATA-XIC 1
IC1004R5G05001N311N-XIC(MCU) 1
IC2201WM8941GEFL/V-WIC 1
IC3001JCY0246IC 1
IC3002XC6213B312NG-XIC 1
IC3003XC8101AA01NG-XIC 1
IC3003 orXC8101AA01N-XIC 1
IC3101K4X1G323PF-8GD8IC 1
IC3201M29W64T70A6E233IC(MICRO C ROM)MP 1
IC3201 orM29W64T70A6E232IC(MICRO C ROM)AP 1
IC3701BH76061GU-XIC 1 B,C
IC4601R2A30451BM-XIC 1
IC6001MAX8934EETI-XIC 1
IC6002BD9639MWV-XIC 1
IC6003XC6215B282NG-XIC 1
IC6004XC6220B271MG-XIC 1
Q24622SC5383/EF/-XTRANSISTOR 1
Q2462 or2SC4617/RS/-XTRANSISTOR 1
Q2462 orDSC9001/R/-XTRANSISTOR 1
Q3001RT3T22M-XDIGI TRANSISTOR 1
Q3002RT3T22M-XDIGI TRANSISTOR 1
Q3003FK330601-XMOS FET 1
Q3004FC694601-WMOS FET 1
Q4502RT3AMMAM1/EF/-XPAIR TRANSISTOR 1
Q4502 orXP4401-WTRANSISTOR 1
Q4502 orBC856S-XPAIR TRANSISTOR 1
Q4502 orPUMT1-WPAIR TRANSISTOR 1
Q4602CPT-290S-C-XPHOTO TRANSISTOR 1
Q6101MTM13124-XMOS FET 1
Q6102RT1N432U-XDIGI TRANSISTOR 1
Q6102 orDRC9143X-XDIGI TRANSISTOR 1
Q6105RT3T22M-XDIGI TRANSISTOR 1
Q6903RT1N432U-XDIGI TRANSISTOR 1
Q6904FK330601-XMOS FET 1
Q6907RT1P44HU-XDIGI TRANSISTOR 1
Q6908FK330601-XMOS FET 1
D6101DB22320-XSB DIODE 1
D6901DA3S103E-XSI DIODE 1
C1004NCBA1AK-104WC CAPACITOR0.1uF 10V K 1
C1009NCBA1AK-104WC CAPACITOR0.1uF 10V K 1
C1010NCBA1AK-104WC CAPACITOR0.1uF 10V K 1
C1012NCBA1AK-104WC CAPACITOR0.1uF 10V K 1
C1020NCB31CK-104XC CAPACITOR0.1uF 16V 1
C1021NCBA1AK-104WC CAPACITOR0.1uF 10V K 1
C2251NCB20JK-475XC CAPACITOR4.7uF 6.3V K 1
C2462NCB20JK-106XC CAPACITOR10uF 6.3V K 1
C2602NCB20JK-475XC CAPACITOR4.7uF 6.3V K 1
C2603NCB31CK-105XC CAPACITOR1uF 16V K 1
C2604NCBA1CK-103WC CAPACITOR0.01uF 16V K 1
C2605NCBA1EK-472WC CAPACITOR4700pF 25V K 1
C2801NCB31CK-105XC CAPACITOR1uF 16V K 1
C3001NCBA1AK-104WC CAPACITOR0.1uF 10V K 1
C3002NCBA1AK-104WC CAPACITOR0.1uF 10V K 1
C3003NCBA1AK-104WC CAPACITOR0.1uF 10V K 1
C3007NCBA1AK-104WC CAPACITOR0.1uF 10V K 1
C3008NCBA1AK-104WC CAPACITOR0.1uF 10V K 1
C3009NCBA1AK-104WC CAPACITOR0.1uF 10V K 1
C3011NCBA1AK-104WC CAPACITOR0.1uF 10V K 1
C3012NCBA1AK-104WC CAPACITOR0.1uF 10V K 1
C3013NCBA1AK-104WC CAPACITOR0.1uF 10V K 1
C3014NCBA1AK-104WC CAPACITOR0.1uF 10V K 1
C3015NCB31CK-104XC CAPACITOR0.1uF 16V 1
C3016NCBA1AK-104WC CAPACITOR0.1uF 10V K 1
(No.YF365<Rev.001>)8/
MODELMARKMODELMARKMODELMARK
12
GZ-HM30BKRAGZ-HM30BUABGZ-HM30BUBC
Safe Symbol No. Parts No.Parts NameDescriptionQTYLocal
C3024NCBA1AK-104WC CAPACITOR0.1uF 10V K 1
C3026NCBA1AK-104WC CAPACITOR0.1uF 10V K 1
C3028NCB20JK-106XC CAPACITOR10uF 6.3V K 1
C3032NCB31CK-105XC CAPACITOR1uF 16V K 1
C3041NCBA1AK-104WC CAPACITOR0.1uF 10V K 1
C3042NCBA1AK-104WC CAPACITOR0.1uF 10V K 1
C3045NCBA1AK-104WC CAPACITOR0.1uF 10V K 1
C3047NRSA6AJ-0R0WMG RESISTOR0Ω 1/16W J 1
C3048NRSA6AJ-0R0WMG RESISTOR0Ω 1/16W J 1
C3050NCBA1AK-104WC CAPACITOR0.1uF 10V K 1
C3054NCB20JK-106XC CAPACITOR10uF 6.3V K 1
C3059NCB31CK-105XC CAPACITOR1uF 16V K 1
C3060NCBA0JK-224WC CAPACITOR0.22uF 6.3V K 1
C3072NCB20JK-106XC CAPACITOR10uF 6.3V K 1
C3075NCB20JK-106XC CAPACITOR10uF 6.3V K 1
C3076NCBA1AK-104WC CAPACITOR0.1uF 10V K 1
C3101NCBA1AK-104WC CAPACITOR0.1uF 10V K 1
C3102NCBA1AK-104WC CAPACITOR0.1uF 10V K 1
C3103NCBA1AK-104WC CAPACITOR0.1uF 10V K 1
C3104NCBA1AK-104WC CAPACITOR0.1uF 10V K 1
C3701NCJ30JK-475X-AC CAPACITOR4.7uF 6.3V K 1 B,C
C3702NCJ30JK-475X-AC CAPACITOR4.7uF 6.3V K 1 B,C
C3704NCB31CK-105XC CAPACITOR1uF 16V K 1 B,C
C3705NCB31CK-105XC CAPACITOR1uF 16V K 1 B,C
C3706NCB31CK-105XC CAPACITOR1uF 16V K 1 B,C
C3707NCB31CK-105XC CAPACITOR1uF 16V K 1 B,C
C3708NCJ30JK-475X-AC CAPACITOR4.7uF 6.3V K 1 B,C
C4604NCB20JK-106XC CAPACITOR10uF 6.3V K 1
C6001NCBA1CK-103WC CAPACITOR0.01uF 16V K 1
C6009NCBA1CK-103WC CAPACITOR0.01uF 16V K 1
C6101NCB20JK-106XC CAPACITOR10uF 6.3V K 1
C6102NCB31CK-105XC CAPACITOR1uF 16V K 1
C6105NCB20JK-106XC CAPACITOR10uF 6.3V K 1
C6106NCB20JK-106XC CAPACITOR10uF 6.3V K 1
C6108NDCA1HJ-101WC CAPACITOR100pF 50V J 1
C6201NCB20JK-106XC CAPACITOR10uF 6.3V K 1
C6202NCJ30JM-106X-AC CAPACITOR10uF 6.3V M 1
C6203NCJ30JM-106X-AC CAPACITOR10uF 6.3V M 1
C6204NDCA1HJ-330WC CAPACITOR33pF 50V J 1
C6301NCB20JK-106XC CAPACITOR10uF 6.3V K 1
C6303NCB20JK-106XC CAPACITOR10uF 6.3V K 1
C6304NDCA1HJ-101WC CAPACITOR100pF 50V J 1
C6305NCB31CK-105XC CAPACITOR1uF 16V K 1
C6306NCB31CK-105XC CAPACITOR1uF 16V K 1
C6401NCB20JK-106XC CAPACITOR10uF 6.3V K 1
C6402NCB20JK-106XC CAPACITOR10uF 6.3V K 1
C6403NCB20JK-106XC CAPACITOR10uF 6.3V K 1
C6501NCB31CK-105XC CAPACITOR1uF 16V K 1
C6502NCB20JK-106XC CAPACITOR10uF 6.3V K 1
C6503NDCA1HJ-101WC CAPACITOR100pF 50V J 1
C6601NRSA02J-0R0XMG RESISTOR0Ω 1/10W J 1
C6901NCB20JK-106XC CAPACITOR10uF 6.3V K 1
C6903NCB20JK-475XC CAPACITOR4.7uF 6.3V K 1
C6904NCB20JK-475XC CAPACITOR4.7uF 6.3V K 1
C6905NCB31CK-105XC CAPACITOR1uF 16V K 1
C6906NCBA1AK-104WC CAPACITOR0.1uF 10V K 1
C6907NCB31CK-105XC CAPACITOR1uF 16V K 1
C6909NCB31CK-105XC CAPACITOR1uF 16V K 1
C6910NCB20JK-475XC CAPACITOR4.7uF 6.3V K 1
C9001NCBA1AK-104WC CAPACITOR0.1uF 10V K 1
C9005NCBA1AK-104WC CAPACITOR0.1uF 10V K 1
C9007NCB21EK-105XC CAPACITOR1uF 25V K 1
C9010NCB20JK-475XC CAPACITOR4.7uF 6.3V K 1
C9016NCBA1AK-104WC CAPACITOR0.1uF 10V K 1
C9017NCBA1AK-104WC CAPACITOR0.1uF 10V K 1
R1002NRSA6AJ-105WMG RESISTOR1MΩ 1/16W J 1
R1005NRSA6AJ-473WMG RESISTOR47kΩ 1/16W J 1
R1006NRSA6AJ-102WMG RESISTOR1kΩ 1/16W J 1
R1011NRSA6AJ-102WMG RESISTOR1kΩ 1/16W J 1
R1012NRSA6AJ-104WMG RESISTOR100kΩ 1/16W J 1
R1013NRSA6AJ-102WMG RESISTOR1kΩ 1/16W J 1
R1014NRSA6AJ-103WMG RESISTOR10kΩ 1/16W J 1
R1017NRSA6AJ-331WMG RESISTOR330Ω 1/16W J 1
R1018NRSA6AJ-331WMG RESISTOR330Ω 1/16W J 1
R1022NRSA6AJ-103WMG RESISTOR10kΩ 1/16W J 1
R1024NRSA6AJ-101WMG RESISTOR100Ω 1/16W J 1
R1025NRSA6AJ-101WMG RESISTOR100Ω 1/16W J 1
R1026NRSA6AJ-101WMG RESISTOR100Ω 1/16W J 1
R1027NRSA6AJ-471WMG RESISTOR470Ω 1/16W J 1
R1028NRSA6AJ-101WMG RESISTOR100Ω 1/16W J 1
R1030NRSA6AJ-102WMG RESISTOR1kΩ 1/16W J 1
R1032NRSA6AJ-103WMG RESISTOR10kΩ 1/16W J 1
R1034NRSA6AJ-105WMG RESISTOR1MΩ 1/16W J 1
R1035NRSA6AJ-104WMG RESISTOR100kΩ 1/16W J 1
R1053NRSA6AJ-474WMG RESISTOR470kΩ 1/16W J 1
R1061NRSA6AJ-474WMG RESISTOR470kΩ 1/16W J 1
R1090NRSA6AJ-102WMG RESISTOR1kΩ 1/16W J 1
R2131NRSA6AJ-222WMG RESISTOR2.2kΩ 1/16W J 1
R2200NRSA6AD-750WMG RESISTOR75Ω 1/16W D 1
R2203NRSA6AJ-100WMG RESISTOR10Ω 1/16W J 1
R2204NRSA6AJ-100WMG RESISTOR10Ω 1/16W J 1
R2251NRSA6AD-181WMG RESISTOR180Ω 1/16W D 1
R2255NRSA6AJ-0R0WMG RESISTOR0Ω 1/16W J 1
(No.YF365<Rev.001>)9/
MODELMARKMODELMARKMODELMARK
12
GZ-HM30BKRAGZ-HM30BUABGZ-HM30BUBC
Safe Symbol No. Parts No.Parts NameDescriptionQTYLocal
R2404NRSA6AJ-100WMG RESISTOR10Ω 1/16W J 1
R2462NRSA6AJ-472WMG RESISTOR4.7kΩ 1/16W J 1
R2463NRSA6AJ-183WMG RESISTOR18kΩ 1/16W J 1
R2801NRSA6AJ-334WMG RESISTOR330kΩ 1/16W J 1
R2802NRSA6AJ-471WMG RESISTOR470Ω 1/16W J 1
R2803NRSA6AJ-0R0WMG RESISTOR0Ω 1/16W J 1
R3002NRSA6AJ-102WMG RESISTOR1kΩ 1/16W J 1
R3004NRSA6AJ-223WMG RESISTOR22kΩ 1/16W J 1
R3005NRSA6AJ-223WMG RESISTOR22kΩ 1/16W J 1
R3017NRSA6AJ-102WMG RESISTOR1kΩ 1/16W J 1
R3020NRSA6AD-512WMG RESISTOR5.1kΩ 1/16W D 1
R3021NRSA6AD-123WMG RESISTOR12kΩ 1/16W D 1
R3022NRSA6AD-151WMG RESISTOR150Ω 1/16W D 1
R3023NRSA6AD-153WMG RESISTOR15kΩ 1/16W D 1
R3024NRSA6AD-113WMG RESISTOR11kΩ 1/16W D 1
R3025NRSA6AD-332WMG RESISTOR3.3kΩ 1/16W D 1
R3028NRSA6AJ-101WMG RESISTOR100Ω 1/16W J 1
R3031NRSA6AJ-101WMG RESISTOR100Ω 1/16W J 1
R3032NRSA6AJ-101WMG RESISTOR100Ω 1/16W J 1
R3033NRSA6AJ-101WMG RESISTOR100Ω 1/16W J 1
R3034NRSA6AJ-101WMG RESISTOR100Ω 1/16W J 1
R3035NRSA6AJ-101WMG RESISTOR100Ω 1/16W J 1
R3036NRSA6AJ-101WMG RESISTOR100Ω 1/16W J 1
R3039NRSA6AJ-0R0WMG RESISTOR0Ω 1/16W J 1
R3048NRSA6AJ-273WMG RESISTOR27kΩ 1/16W J 1
R3052NRSA6AJ-222WMG RESISTOR2.2kΩ 1/16W J 1
R3053NRSA6AJ-222WMG RESISTOR2.2kΩ 1/16W J 1
R3054NRSA6AJ-222WMG RESISTOR2.2kΩ 1/16W J 1
R3057NRSA6AJ-222WMG RESISTOR2.2kΩ 1/16W J 1
R3058NRSA6AJ-473WMG RESISTOR47kΩ 1/16W J 1
R3061NRSA6AJ-0R0WMG RESISTOR0Ω 1/16W J 1
R3065NRSA6AJ-100WMG RESISTOR10Ω 1/16W J 1
R3069NRSA6AJ-102WMG RESISTOR1kΩ 1/16W J 1
R3070NRSA6AJ-102WMG RESISTOR1kΩ 1/16W J 1
R3074NRSA6AJ-0R0WMG RESISTOR0Ω 1/16W J 1
R3075NRSA6AD-820WMG RESISTOR82Ω 1/16W D 1 B,C
R3076NRSA6AD-820WMG RESISTOR82Ω 1/16W D 1 B,C
R3079NRSA6AJ-100WMG RESISTOR10Ω 1/16W J 1
R3081NRSA6AJ-100WMG RESISTOR10Ω 1/16W J 1
R3088NRSA6AJ-103WMG RESISTOR10kΩ 1/16W J 1
R3096NRSA6AJ-0R0WMG RESISTOR0Ω 1/16W J 1
R3097NRSA6AJ-102WMG RESISTOR1kΩ 1/16W J 1
R3098NRSA6AJ-100WMG RESISTOR10Ω 1/16W J 1
R3127NRSA6AJ-152WMG RESISTOR1.5kΩ 1/16W J 1 B,C
R3128NRSA6AJ-152WMG RESISTOR1.5kΩ 1/16W J 1
R3129NRSA6AJ-153WMG RESISTOR15kΩ 1/16W J 1
R3130NRSA6AJ-153WMG RESISTOR15kΩ 1/16W J 1
R3131NRSA6AJ-393WMG RESISTOR39kΩ 1/16W J 1
R3132NRSA6AJ-393WMG RESISTOR39kΩ 1/16W J 1
R3133NRSA6AJ-473WMG RESISTOR47kΩ 1/16W J 1
R3134NRSA6AJ-222WMG RESISTOR2.2kΩ 1/16W J 1
R3135NRSA6AJ-222WMG RESISTOR2.2kΩ 1/16W J 1
R3507NRSA6AJ-101WMG RESISTOR100Ω 1/16W J 1
R3701NRSA6AJ-0R0WMG RESISTOR0Ω 1/16W J 1 B,C
R3702NRSA6AD-750WMG RESISTOR75Ω 1/16W D 1 B,C
R3703NRSA6AD-750WMG RESISTOR75Ω 1/16W D 1 B,C
R3704NRSA6AD-750WMG RESISTOR75Ω 1/16W D 1 B,C
R4606NRSA6AJ-331WMG RESISTOR330Ω 1/16W J 1
R4607NRSA6AJ-331WMG RESISTOR330Ω 1/16W J 1
R4608NRSA6AJ-121WMG RESISTOR120Ω 1/16W J 1
R4609NRSA6AJ-121WMG RESISTOR120Ω 1/16W J 1
R4680NRSA6AJ-103WMG RESISTOR10kΩ 1/16W J 1
R6001NRSA6AD-103WMG RESISTOR10kΩ 1/16W D 1
R6002NRSA6AD-624WMG RESISTOR620kΩ 1/16W D 1
R6003NRSA6AD-434WMG RESISTOR430kΩ 1/16W D 1
R6004NRSA6AD-684WMG RESISTOR680kΩ 1/16W D 1
R6005NRSA6AD-564WMG RESISTOR560kΩ 1/16W D 1
R6101NRSA6AJ-100WMG RESISTOR10Ω 1/16W J 1
R6102NRSA6AD-624WMG RESISTOR620kΩ 1/16W D 1
R6103NRSA6AD-243WMG RESISTOR24kΩ 1/16W D 1
R6104NRSA6AD-563WMG RESISTOR56kΩ 1/16W D 1
R6108NRSA6AJ-104WMG RESISTOR100kΩ 1/16W J 1
R6109NRSA6AJ-185WMG RESISTOR1.8MΩ 1/16W J 1
R6201NRSA6AD-513WMG RESISTOR51kΩ 1/16W D 1
R6202NRSA6AD-104WMG RESISTOR100kΩ 1/16W D 1
R6203NRSA6AD-432WMG RESISTOR4.3kΩ 1/16W D 1
R6301NRSA6AD-104WMG RESISTOR100kΩ 1/16W D 1
R6302NRSA6AD-153WMG RESISTOR15kΩ 1/16W D 1
R6303NRSA6AD-152WMG RESISTOR1.5kΩ 1/16W D 1
R6402NRSA6AJ-333WMG RESISTOR33kΩ 1/16W J 1
R6403NRSA6AJ-153WMG RESISTOR15kΩ 1/16W J 1
R6501NRSA6AD-162WMG RESISTOR1.6kΩ 1/16W D 1
R6502NRSA6AD-273WMG RESISTOR27kΩ 1/16W D 1
R6503NRSA6AD-104WMG RESISTOR100kΩ 1/16W D 1
R6601NRSA6AJ-0R0WMG RESISTOR0Ω 1/16W J 1
R6602NRSA6AJ-0R0WMG RESISTOR0Ω 1/16W J 1
R6901NRSA6AD-103WMG RESISTOR10kΩ 1/16W D 1
R6902NRSA6AD-152WMG RESISTOR1.5kΩ 1/16W D 1
R6903NRSA6AD-133WMG RESISTOR13kΩ 1/16W D 1
R6907NRSA6AD-564WMG RESISTOR560kΩ 1/16W D 1
R6908NRSA6AD-224WMG RESISTOR220kΩ 1/16W D 1
R6913NRSA6AD-622WMG RESISTOR6.2kΩ 1/16W D 1
(No.YF365<Rev.001>)10/
MODELMARKMODELMARKMODELMARK
12
GZ-HM30BKRAGZ-HM30BUABGZ-HM30BUBC
Safe Symbol No. Parts No.Parts NameDescriptionQTYLocal
R6922NRSA6AJ-105WMG RESISTOR1MΩ 1/16W J 1
R9001NRSA6AJ-682WMG RESISTOR6.8kΩ 1/16W J 1
R9002NRSA6AJ-223WMG RESISTOR22kΩ 1/16W J 1
R9003NRSA6AJ-104WMG RESISTOR100kΩ 1/16W J 1
R9004NRSA6AJ-104WMG RESISTOR100kΩ 1/16W J 1
R9011NRSA6AJ-101WMG RESISTOR100Ω 1/16W J 1
R9012NRSA6AJ-101WMG RESISTOR100Ω 1/16W J 1
R9013NRSA6AJ-101WMG RESISTOR100Ω 1/16W J 1
R9014NRSA6AJ-0R0WMG RESISTOR0Ω 1/16W J 1
R9015NRSA6AJ-101WMG RESISTOR100Ω 1/16W J 1
R9016NRSA6AJ-101WMG RESISTOR100Ω 1/16W J 1
R9017NRSA6AJ-0R0WMG RESISTOR0Ω 1/16W J 1
R9018NRSA6AJ-103WMG RESISTOR10kΩ 1/16W J 1
R9019NRSA6AJ-0R0WMG RESISTOR0Ω 1/16W J 1
R9029NRSA6AJ-0R0WMG RESISTOR0Ω 1/16W J 1
R9031NRSA6AJ-0R0WMG RESISTOR0Ω 1/16W J 1
R9032NRSA6AJ-0R0WMG RESISTOR0Ω 1/16W J 1
R9034NRSA6AJ-0R0WMG RESISTOR0Ω 1/16W J 1
R9035NRSA6AJ-0R0WMG RESISTOR0Ω 1/16W J 1
R9036NRSA6AJ-0R0WMG RESISTOR0Ω 1/16W J 1
R9037NRSA63J-0R0XMG RESISTOR0Ω 1/10W J 1
R9038NRSA63J-0R0XMG RESISTOR0Ω 1/10W J 1
R9043NRSA6AJ-0R0WMG RESISTOR0Ω 1/16W J 1
RA1001NRB04CJ-103WNET RESISTOR10kΩ J 1
RA1002NRB04CJ-102WNET RESISTOR1kΩ J 1
RA1003NRB04CJ-474WNET RESISTOR470kΩ J 1
RA1004NRB04CJ-474WNET RESISTOR470kΩ J 1
RA3002NRB04CJ-100WNET RESISTOR10Ω J 1
RA3003NRB04CJ-100WNET RESISTOR10Ω J 1
RA3004NRB04CJ-0R0WNET RESISTOR0Ω J 1
RA3008NRB04CJ-0R0WNET RESISTOR0Ω J 1
RA3009NRB04CJ-102WNET RESISTOR1kΩ J 1
RA3010NRB04CJ-0R0WNET RESISTOR0Ω J 1
RA3011NRB04CJ-472WNET RESISTOR4.7kΩ J 1
RA9001NRB04CJ-473WNET RESISTOR47kΩ J 1
L2402NQLC32M-100XCOIL10uH M 1
L3001NQR0679-003XCHOKE COIL 1
L3002NQR0679-003XCHOKE COIL 1
L3701NRSA63J-0R0XMG RESISTOR0Ω 1/10W J 1 B,C
L4601NQR0573-005XFERRITE BEADS 1
L6101NQLG4EN-2R3XCOIL2.3uH N 1
L6201NQLG4EN-2R3XCOIL2.3uH N 1
L6301NQLK25N-4R7XCOIL4.7uH N 1
L6401NQLK25N-3R3XCOIL3.3uH N 1
L6501NQLK25N-6R8XCOIL6.8uH N 1
L9001NQR0654-001XEMI FILTER 1
L9002NQR0022-004XFERRITE BEADS 1
CN4602QGF0543F3-14XCONNECTOR FFC/FPC (1-14) 1
CN9001QGF0528F4-40XCONNECTOR FFC/FPC (1-40) 1
CN9002QGF0534F5-06XCONNECTOR FFC/FPC (1-6) 1
CN9003QGB0519J1-30XCONNECTOR B-B (1-30) 1
CN9004QGF0543F3-18XCONNECTOR FFC/FPC (1-18) 1
CN9005QGF0543F3-24XCONNECTOR FFC/FPC (1-24) 1 B,C
CN9007QGA1001F1-02XCONNECTOR W-B (1-2) 1
CN9008QGF0543F3-06XCONNECTOR FFC/FPC (1-6) 1
CN9009NNZ0255-001XSD CARD CONNE 1
CN9012QGF0528F4-34XCONNECTOR FFC/FPC (1-34) 1
CN9013QGF0543F3-24XCONNECTOR FFC/FPC (1-24) 1
CN9014QGF0543F3-15XCONNECTOR FFC/FPC (1-15) 1 A
K2102NQR0286-009XFERRITE BEADS 1
K2103NRSA6AJ-0R0WMG RESISTOR0Ω 1/16W J 1
K3001NQR0499-001XFERRITE BEADS 1
K3002NQR0499-001XFERRITE BEADS 1
K3004NQR0154-004XFERRITE CORE 1
K3006NQR0286-009XFERRITE BEADS 1
LC3001NQR0652-001XEMI FILTER 1
TH9001NAD0048-473XN THERMISTOR47kΩ 1
TP9001NNZ0163-001XEARTH TERMINAL 1
X1001NAX0491-001XCRYSTAL32.768kHz 1
X3001NAX1118-001XC RESONATOR 1
REAR BOARD ASSEMBLY <02>
PW601LYA20080-08B1REAR BOARD ASSY 1 A
PW601LYA20080-07B1REAR BOARD ASSY 1 B,C
IC601XC6215B332NG-XIC 1
IC901NAL0094-001XGYRO SENSOR 1
D601DZ2J068/M/-XZ DIODE 1
D601 orUDZW6.8B-XZ DIODE 1 B,C
D604DZ2J068/M/-XZ DIODE 1
D604 orUDZW6.8B-XZ DIODE 1 B,C
D605DZ2J068/M/-XZ DIODE 1
D606DB2J314-XSB DIODE 1
D609DB22320-XSB DIODE 1
D611LNJ326W83-XLED 1
D612SML-D12V8W/PQ-XLED 1
C601NCBA1HK-102WC CAPACITOR1000pF 50V K 1
C602NCBA1HK-102WC CAPACITOR1000pF 50V K 1
C607NCBA1AK-104WC CAPACITOR0.1uF 10V K 1
C609NCB31CK-105XC CAPACITOR1uF 16V K 1
C610NCB31CK-105XC CAPACITOR1uF 16V K 1
C901NCBA1CK-103WC CAPACITOR0.01uF 16V K 1
C902NCB31EK-473XC CAPACITOR0.047uF 25V K 1
(No.YF365<Rev.001>)11/
MODELMARKMODELMARKMODELMARK
12
GZ-HM30BKRAGZ-HM30BUABGZ-HM30BUBC
Safe Symbol No. Parts No.Parts NameDescriptionQTYLocal