JVC GR-AX911U User Manual
COMP ACT VHS CAMCORDER
GR-AX911
Compact VHS
INSTRUCTIONS
For Customer Use:
Enter below the Serial Nos. of the
GR-AX911U camcorder and the
AA-V11U AC Power Adapter/Charger.
The serial numbers are located on the
bottom of the GR-AX911U, and the
AA-V11U.
Model No. GR-AX911U
AA-V11U
Serial No.
YU30052-540
2
Dear Customer,
Thank you for purchasing the JVC Compact VHS
camcorder. Before use, please read the safety
information and precautions contained in the following
pages to ensure safe use of your new camcorder.
Using This Instruction Manual
• All major sections and subsections are listed in the Table
Of Contents (
• Notes appear after most subsections. Be sure to read
these as well.
• Basic and advanced features/operation are separated for
easier reference.
It is recommended that you . . .
..... refer to the Index (
familiarize yourself with button locations, etc. before
use.
..... read thoroughly the Safety Precautions and Safety
Instructions that follow. They contain extremely
important information regarding the safe use of your
new camcorder.
You are recommended to carefully read the cautions
on pages 53 and 54 before use.
Z pg. 7).
Z pgs. 49 – 52) and
SAFETY
PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
NO USER-SERVICEABLE PARTS INSIDE.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
The AA-V11U AC Power Adapter/Charger should be
used with:
AC 120 V`, 60 Hz in the USA and Canada,
AC 110 – 240 V`, 50/60 Hz in other countries.
CAUTION (applies to the AA-V11U)
TO PREVENT ELECTRIC SHOCK MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION (s'applique à l'AA-V11U)
POUR ÉVITER LES CHOCS ÉLECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE
DANS LA BORNE CORRESPONDANTE DE LA PRISE
ET POUSSER JUSQU'AU FOND.
WARNING:
TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE
THIS UNIT TO RAIN OR
MOISTURE.
Warning on lithium battery
The battery used in this device may present a fire or
chemical burn hazard if mistreated. Do not recharge,
disassemble, heat above 100°C (212°F) or incinerate.
Replace battery with Panasonic (Matsushita Electric),
Sanyo or Maxell CR2025; use of another battery may
present a risk of fire or explosion.
n Dispose of used battery promptly.
n Keep away from children.
n Do not disassemble and do not dispose of in fire.
NOTES:
●
The rating plate (serial number plate) and safety
caution are on the bottom and/or the back of the
main unit.
●
The rating plate (serial number plate) of the AC
Power Adapter/Charger is on its bottom.
This Class B digital apparatus meets all requirements of
the Canadian Interference – Causing Equipment
Regulations.
“Cet appareil numérique de la classe B respecte toutes
les exigences du Règlement sur le matériel brouilleur
du Canada.”
This camcorder is designed to be used with NTSC-type
color television signals. It cannot be used for playback
with a television of a different standard. However, live
recording and viewfinder playback are possible
anywhere. Use the BN-V11U/V12U/V22U/V25U
battery packs and, to recharge them, the provided
multi-voltage AC Power Adapter/Charger. (An
appropriate conversion adapter may be necessary to
accommodate different designs of AC outlets in
different countries.)
ATTENTION:
The product that you have purchased is powered by a
rechargeable battery. The battery is recyclable. At the
end of its useful life, under various state and local
laws, it may be illegal to dispose of this battery into the
municipal waste stream. Check with your local solid
waste officials for details in your area for recycling
options or proper disposal.
IMPORTANT PRODUCT
SAFETY INSTRUCTIONS
Electrical energy can perform many useful functions. But
improper use can result in potential electrical shock or fire
hazards. This product has been engineered and
manufactured to assure your personal safety. In order not to
defeat the built-in safeguards, observe the following basic
rules for its installation, use and servicing.
ATTENTION:
Follow and obey all warnings and instructions marked on
your product and its operating instructions. For your safety,
please read all the safety and operating instructions before
you operate this product and keep this manual for future
reference.
INSTALLATION
1. Grounding or Polarization
(A) Your product may be equipped with a polarized
alternating-current line plug (a plug having one blade
wider than the other). This plug will fit into the power
outlet only one way. This is a safety feature.
If you are unable to insert the plug fully into the outlet,
try reversing the plug. If the plug should still fail to fit,
contact your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the polarized plug.
(B) Your product may be equipped with a 3-wire
grounding-type plug, a plug having a third (grounding)
pin. This plug will only fit into a grounding-type power
outlet. This is a safety feature.
If you are unable to insert the plug into the outlet,
contact your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the grounding-type
plug.
2. Power Sources
Operate your product only from the type of power source
indicated on the marking label. If you are not sure of the
type of power supply to your home, consult your product
dealer or local power company. If your product is intended
to operate from battery power, or other sources, refer to the
operating instructions.
3. Overloading
Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or
electric shock.
4. Power Cord Protection
Power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs,
convenience receptacles, and the point where they exit
from the product.
5. Ventilation
Slots and openings in the cabinet are provided for
ventilation. To ensure reliable operation of the product and
to protect it from overheating, these openings must not be
blocked or covered.
• Do not block the openings by placing the product on a
bed, sofa, rug or other similar surface.
• Do not place the product in a built-in installation such as
a bookcase or rack unless proper ventilation is provided
or the manufacturer’s instructions have been adhered to.
6. Wall or Ceiling Mounting
The product should be mounted to a wall or ceiling only as
recommended by the manufacturer.
ANTENNA INSTALLATION
INSTRUCTIONS
1. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the
product, be sure the antenna or cable system is grounded
so as to provide some protection against voltage surges and
built-up static charges. Article 810 of the National Electrical
Code, ANSI/NFPA 70, provides information with regard to
proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge unit,
size of grounding conductors, location of antenna
discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode.
2. Lightning
For added protection for this product during a lightning
storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line
surges.
3. Power Lines
An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or
power circuits, or where it can fall into such power lines or
circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such
power lines or circuits as contact with them might be fatal.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
ANTENNA
LEAD IN WIRE
GROUND CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION
ELECTRIC SERVICE
EQUIPMENT
POWER SERVICE GROUNDING ELECTRODE SYSTEM
(NEC ART 250. PART H)
NEC – NATIONAL ELECTRICAL CODE
810-20)
GROUNDING
CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
3
4
USE
1. Accessories
To avoid personal injury:
• Do not place this product on an unstable cart, stand,
tripod, bracket or table. It may fall, causing serious injury
to a child or adult, and serious damage to the product.
• Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer or sold with the
product.
• Use a mounting accessory recommended by the
manufacturer and follow the manufacturer’s instructions
for any mounting of the product.
• Do not try to roll a cart with small casters across
thresholds or deep-pile carpets.
2. Product and Cart Combination
A product and cart combination should be moved with
care. Quick stops, excessive force, and uneven surfaces
may cause the product and cart combination to overturn.
3. Water and Moisture
Do not use this product near
water—for example, near a bath
tub, wash bowl, kitchen sink or
laundry tub, in a wet basement, or
near a swimming pool and the
like.
4. Object and Liquid Entry
Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
5. Attachments
Do not use attachments not recommended by the
manufacturer of this product as they may cause hazards.
6. Cleaning
Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a damp
cloth for cleaning.
7. Heat
The product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.
PORTABLE CART WARNING
(Symbol provided by RETAC)
SERVICING
1. Servicing
If your product is not operating correctly or exhibits a
marked change in performance and you are unable to
restore normal operation by following the detailed
procedure in its operating instructions, do not attempt to
service it yourself as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
2. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing
to qualified service personnel under the following
conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the
product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following
the operating instructions. Adjust only those controls that
are covered by the operating instructions as an improper
adjustment of other controls may result in damage and
will often require extensive work by a qualified
technician to restore the product to its normal operation.
e. If the product has been dropped or damaged in any way.
f. When the product exhibits a distinct change in
performance—this indicates a need for service.
3. Replacement Parts
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer or have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock or other hazards.
4. Safety Check
Upon completion of any service or repairs to this product,
ask the service technician to perform safety checks to
determine that the product is in safe operating condition.
QUICK OPERATION GUIDE
5
SUPPLY POWER
Hook on.
1
Push in.
2
BATT. RELEASE
Using the battery pack
1
Hook-on the battery pack's top end to the
camcorder. (Charging procedure, Z P. 8)
2 Push in the battery pack until it locks into
place.
To remove the battery pack
Slide BATT. RELEASE and pull out the battery
pack.
PLAYBACK
PLAY/PAUSE
3
REW
2
STOP
INSERTING A VIDEO
CASSETTE
EJECT
1
3
PUSH
1 Slide EJECT.
2 Insert a video cassette.
3 Press PUSH.
(For more details, Z P. 13)
SHOOTING
2
Insert.
LENS COVER
open/close knob
2
Set to “CAMERA”
Recording Start/Stop button
3
1
1
Set to “PLAY”
1 Set the power switch to “PLAY”.
2 Press REW.
— The tape will automatically stop at the
beginning of the tape.
3 Press PLAY/PAUSE.
— Playback starts and the playback picture
appears in the viewfinder.
•To stop playback, press STOP.
(For more details, Z P. 38.)
Or simply play back the tape on a VHS
n
VCR using the Cassette Adapter
(VHS Playpak). Z P. 36
1 Slide the LENS COVER open/close knob to
open the lens cover.
2 Set the power switch to “CAMERA”.
— The power indicator will light and an
image will appear in the viewfinder.
3 Press RECORDING START/STOP.
— Recording starts.
•To stop recording temporarily, momentarily
press the Recording Start/Stop button once
again.
(For more details, Z P. 16)
6
MAJOR FEATURES
REMEMBER
The Logical Choice
The only compact video
cassettes that can be
used with your VHS VCR*
Program AE with Special
Effects (
n Cinema n Sepia n Twilight n Sports
n High Speed (1/2000 sec.) Shutter
n Classic Film n Strobe n Slow Shutter
Z pg. 26)
Digital Wipes and Fades
Z pg. 28)
(
● Black Fader ● Blue Fader
● Mosaic Fader ● Shutter Wipe
● Slide Wipe ● Corner Wipe
● Dissolve ● Auto Select
*
with VHS Playpak
Multi Function Control
Z pg. 22 – 35)
(
Digital Hyper Zoom (
Zoom-in
W
T
W
T
Zoom-out
Z pg. 17)
W
T
Digital Image Stabilizer
Z pg. 22)
(
Random Assemble Editing
Z pg. 40 – 43)
(
882
554411663
7
W
T
Built-In Auto Light (Z pg.19)
PROVIDED ACCESSORIES
•AC Power Adapter/
Charger AA-V11U
•DC Cord
•Remote Control
Unit RM-V705U
Cassettes marked can be used with this camcorder.
•Cassette Adapter
(VHS PlayPak) C-P7U
•Lithium Battery
CR2025
3
2
7
•Battery Pack
BN-V11U
•Shoulder
Strap
CONTENTS
GETTING STARTED
Power ................................................................................................ 8
Clock (Lithium) Battery Removal/Insertion................................................... 10
Viewfinder Adjustment .......................................................................... 10
Date/Time Setting ............................................................................... 11
Tape Length Setting .............................................................................. 12
Recording Mode Setting ......................................................................... 13
Loading/Unloading A Cassette ................................................................. 13
Grip Adjustment .................................................................................. 14
Shoulder Strap Attachment ...................................................................... 14
Tripod Mounting ..................................................................................14
Using The RM-V705U Remote Control Unit .................................................. 15
RECORDING
Basic Recording ...................................................................................16
Basic Features..................................................................................... 17
Video Light ........................................................................................ 19
Advanced Features ............................................................................... 20
PLAYBACK
Using The Cassette Adapter..................................................................... 36
Basic Connections .................................................................................37
Basic Playback .................................................................................... 38
Features ........................................................................................... 39
EDITING
Tape Dubbing ...................................................................................... 40
Random Assemble Editing [R.A.Edit]...........................................................40
Insert Editing ......................................................................................44
Audio Dubbing.....................................................................................45
USER MAINTENANCE
TROUBLESHOOTING
INDEX
Controls ............................................................................................49
Connectors......................................................................................... 50
Indicators .......................................................................................... 50
Other Parts ........................................................................................50
Viewfinder ........................................................................................ 51
Terms ............................................................................................... 52
CAUTIONS
SPECIFICATIONS
ESPAÑOL
FOR SERVICING
WARRANTY
16
Date/Time Insert ................................................................................... 20
Snapshot .............................................................................................. 21
Digital Image Stabilizer (D.I.S.) .............................................................. 22
Exposure Control .................................................................................. 22
White Balance Adjustment..................................................................... 23
Focusing ............................................................................................... 24
Program AE With Special Effects............................................................. 26
Fade/Wipe ............................................................................................ 28
Using Menu For Detailed Adjustment. .................................................... 30
Instant Titles ......................................................................................... 32
Self-Timer............................................................................................. 34
Animation ............................................................................................ 35
Time Lapse ........................................................................................... 35
36
40
46
47
49
53
55
56
58
59
7
8
GETTING STARTED
RECORDING
PLAYBACK
EDITING
8
END
indicator
CHG. (charge) indicator
Marks
POWER
indicator
REFRESH indicatorREFRESH switch
To AC outlet
GETTING STARTED
Power
This camcorder’s 3-way power supply system lets you
choose the most appropriate source of power.
NOTES:
●
No function is available without power supply.
●
Use only specified power supply.
●
Do not use provided power supply units with other equipment.
CHARGING THE BATTERY PACK
SUPPLY POWER
Connect the charger’s AC power cord to a wall
1
outlet. The power indicator lights.
ATTACH BATTERY PACK
Align the marks and slide the battery pack in the
2
direction of the arrow until it locks in place.
The CHG. indicator lights.
DETACH BATTERY PACK
When charging is completed, the END indicator
3
lights. Slide the battery pack opposite the direction
of the arrow.
BATT. PACK CHARGE DISCHARGE
BN-V11U approx. 1 hr. 10 min. approx. 3 hrs. 30 min.
BN-V12U approx. 1 hr. 10 min. approx. 3 hrs. 30 min.
BN-V22U approx. 2 hrs. 10 min. approx. 7 hrs.
BN-V25U approx. 2 hrs. 40 min. approx. 10 hrs.
Hook on.
Push in.
BATT. RELEASE
ATTENTION:
Before detaching the power source,
make sure that the camcorder’s power
is turned off. Failure to do so can result
in a camcorder malfunction.
USING THE BATTERY PACK
ATTACH BATTERY PACK
Hook its top end to the camcorder and push the
1
battery pack in until it locks in place.
DETACH BATTERY PACK
Slide BATT. RELEASE and pull out the battery pack.
2
BATT. PACK RECORDING TIME
BN-V11U approx. 1 hr. 5 min. (35 min.)
BN-V12U approx. 1 hr. 5 min. (35 min.)
BN-V22U approx. 2 hrs. 15 min. (1 hr. 25 min.)
BN-V25U approx. 3 hrs. (1 hr. 50 min.)
( ): When the Video Light is on
**REFRESH
The AC power adapter features a REFRESH function that allows
you to fully discharge the battery pack before recharging.
To discharge the battery . . .
..... attach the battery pack to the adapter as shown in the
illustration to the left. Then push REFRESH. The REFRESH
indicator lights when discharging starts, and goes out when
discharging is complete.
**CHARGE MARKER
Charge marker
A charge marker is provided on the battery pack to
help you remember whether it has been charged or
not. Two colors are provided (red and black)—you
choose which one means charged and which
means discharged.
NOTES:
●
The recording time per charge is affected by such factors as the time spent in Record/Standby mode and
the frequency of zooming. It is safer to have spare battery packs.
●
Charging times noted on page 8 are for fully discharged battey pack, and discharging times are for fully
charged battery pack.
●
Charging and discharging times vary according to the ambient temperature and the status of the battery
pack.
●
Remember to set the charge marker after charging a battery pack or after detaching a discharged one from
your camcorder.
●
Perform the REFRESH function after no less than 5 chargings.
●
High temperatures can damage the battery pack, so use only where good ventilation is available. Don’t
allow it to discharge in container, such as a bag.
●
If you stop recharging or discharging part way through, make sure to remove the battery pack before
unplugging the adapter’s AC cord.
●
Remove the battery pack from the adapter immediately after discharging.
●
To avoid interference with reception, do not use the AC Power Adapter/Charger near a radio.
●
Make sure you unplug the DC cord before charging or discharging the battery pack.
●
A blinking CHG. indicator means that the battery pack has become hot. Wait until it cools down to
continue.
●
The CHG. indicator may not light properly with a brand new battery pack, or with one that’s been stored
for an extended period. In this case, remove and reattach the battery pack and recharge it. The CHG.
indicator should light during recharging. If not, contact your nearest JVC dealer.
9
To
DC OUT
To
terminal
DC IN
Jack
DC cord
Car Battery Cord
AP-V7U (optional)
Car Battery Charger/Adapter
BH-V3U (optional)
To AC outlet
AC Power
Adapter/Charger
AA-V11U (provided)
To car's
cigarette
lighter
socket
USING A CAR BATTERY
Use the optional Car Battery Cord or Car Battery
Charger/Adapter (connect as shown in the
illustration to the left).
NOTES:
●
When using the car battery, leave the engine
idling.
●
The optional Car Battery Charger (BH-V3U) can
also be used to charge the battery pack.
●
When using the optional Car Battery Charger or
Car Battery Cord (AP-V7U), refer to the respective
instruction booklet.
USING AC POWER
Use the AC Power Adapter (connect as shown in
the illustration to the left).
NOTE:
The supplied AC Power Adapter/Charger features
automatic voltage selection in the AC range from
110 V to 240 V.
10
GETTING STARTED (cont.)
A
Clock (Lithium) Battery Insertion/Removal
This battery is necessary for clock operation and to
perform date/time settings.
SWITCH OFF POWER
Switch off the unit’s power and remove the power
1
supply unit.
OPEN COVER
Open the clock battery compartment cover while
2
pressing the release tab.
REMOVE BATTERY (when replacing)
Insert a pointed, non-metallic object between the
3
battery and the compartment (
battery out.
INSERT BATTERY
Ensuring the plus (+) side is up, insert a CR2025
4
lithium battery and push it in.
CLOSE COVER
Close the compartment cover until it clicks in place.
A
) and pull the
5
NOTE:
See “SAFETY PRECAUTIONS”(Z pg. 2) for information
on safe handling of lithium batteries.
3
1
Set POWER to “CAMERA”.
2
Viewfinder Adjustment
POSITION VIEWFINDER
Adjust the viewfinder manually for best viewability
1
(see illustration at left).
SELECT MODE
Set the power switch to CAMERA.
2
ADJUST DIOPTER
Turn the diopter adjustment control until the
3
indications in the viewfinder are clearly focused.
Shooting mode selector
FAR
+ MENU
NEAR
–
Main Menu
Screen
Set Time and
Date Screen
Shift Zoom OFF
Tele Macro OFF
Gain Up AGC
Color Filter NOR.
Tape Length T30
Title
Date/Time
Sub Menu
JAN 1.00 AM 12:00
Set
Cancel
11
Date/Time Setting
SELECT MODE
Set the Power switch to “CAMERA”, and the
1
Shooting Mode selector to “PRESET”.
ACCESS MAIN MENU SCREEN
Press MENU.
2
SELECT FUNCTION
Press – to move the highlight bar down to “Date/
3
Time”, then press NEAR. The Set Date And Time
screen appears.
SET DATE/TIME
Press FAR or NEAR until the item you want to set
4
begins blinking, then press + or – to until the correct
setting appears.
•If you decide you want to return the date and time
to the previous settings, press FAR or NEAR to
move the highlight bar to “Cancel”, then press
MENU.
•If you’re satisfied with the settings, go on to step 5.
START CLOCK OPERATION
Once you’ve set the month, day, year and time,
5
press FAR or NEAR until “Set” begins to blink, then
press MENU. The Main Menu screen reappears.
CLOSE MAIN MENU
Press MENU.
6
NOTES:
●
To display the date and time in the viewfinder and on a
connected TV, see “Date/Time Insert” (Z pg. 20).
●
If, in step 4, you input an invalid date (FEB 30, JUN 31,
etc.) and perform step 5, “Input Error” appears blinking
at the bottom of the screen. Press +, –, FAR or NEAR to
make the day blink, and input the correct number.
Date
Month/Day/Year
Time
12-hour indication with
AM or PM
12
Shooting mode selector
FAR
+
MENU
GETTING STARTED (cont.)
Tape Length Setting
SELECT MODE
Set the Power switch to “CAMERA”, and the
1
Shooting Mode selector to “PRESET”.
ACCESS MAIN MENU SCREEN
Press MENU.
2
–
Main Menu
Screen
NEAR
Shift Zoom OFF
Tele Macro OFF
Gain Up AGC
Color Filter NOR.
Tape Length T40
Title
Date/Time
Sub Menu
T20
SELECT FUNCTION
Press + or – to move the highlight bar to “Tape
3
Length”.
SET TAPE LENGTH
Press FAR or NEAR to cycle through until the correct
4
setting appears (depending on the tape used). T20 =
20 minutes of recording time, T30 = 30 min., and
T40 = 40 min. (when recording in SP mode).
CLOSE MAIN MENU
Press MENU.
5
NOTE:
The tape remaining time (Z pg. 16) displayed in the
viewfinder is correct only if the correct tape length has
been selected.
T40
T30
SP/EP
13
Recording Mode Setting
Pressing SP/EP alternates the setting between SP
1
(standard play-provides higher picture and sound
quality, better for dubbing) and EP (Extended Playmore economical, recording at 1/3 the speed of SP).
NOTE:
If the recording mode is switched during recording, the
playback picture will be blurred at the switching point.
Loading/Unloading A Cassette
OPEN CASSETTE HOLDER
Slide EJECT until the holder opens. Do not use force
1
to open.
INSERT/REMOVE CASSETTE
Make sure the label is facing outward.
2
CLOSE CASSETTE HOLDER
Press PUSH and make sure the holder is closed and
3
locked.
NOTES:
●
A cassette holder can’t be opened unless a power
supply is attached.
●
Make sure that the tape is not slack when loading the
cassette. If there is any slack, turn the gear on the
cassette in the direction of the arrow to take up the
slack.
●
Make sure the Erase Protection tab is present. If not,
cover the hole with adhesive tape. (Some cassettes
have sliding tabs – in this case, check the tab's
position.)
Turn to take up
slack.
GearErase Protection
14
3
Recording Start/Stop button
1
2
1
2
GETTING STARTED (cont.)
Grip Adjustment
EXPAND LOOP
Separate the Velcro strip.
1
INSERT HAND
Pass your right hand through the loop and grasp the
2
grip.
ADJUST STRAP LENGTH
Adjust so your thumb and fingers can easily operate
3
the Recording Start/Stop button and Power Zoom
lever. Refasten the Velcro strip.
Shoulder Strap Attachment
ATTACH STRAP
Following the illustration at left, thread the strap
1
through the top of the eyelet 1, then fold it back
and thread it through the keeper 2, and then
through the buckle 3. Repeat the procedure to
attach the other end of the strap to the other eyelet,
making sure the strap isn’t twisted.
ADJUST LENGTH
Adjust as shown in the illustration at left 1, then
2
slide both keepers snug against the eyelets to
prevent slipping 2.
Tripod Mounting
ALIGN AND TIGHTEN
Align the screw and camera direction stud on the
1
tripod with the camera’s mounting socket and stud
hole. Then tighten the screw.
Using The RM-V705U Remote Control Unit
The Full-Function Remote Control Unit can operate this camcorder from a distance as well as the basic
operations (PLAY, STOP, PAUSE, FF, and REW) of your VCR. This remote control unit makes additional
recording functions possible.
PULL OUT BATTERY HOLDER
Infrared beam
effective area
10°
5m(16.4ft)
30°
30°
10°
The transmitted beam may not be effective or may
cause incorrect operation when the infrared beam
sensor window is directly exposed to sunlight or
powerful lighting.
Infrared beam
sensor window
1
Pull out the battery holder by inserting a pointed instrument
into slot .
1
INSERT BATTERY
Insert the lithium battery *(CR2025), with its plus (+) side
up, into the battery holder.
2
REPLACE BATTERY HOLDER
Insert the battery holder into the remote control unit, and
push the holder until it clicks in place.
3
*Read warning on lithium battery. (
Z P. 2)
15
2
7
8
3
4
5
6
Buttons
1 Infrared beam Transmits the beam signal.
transmitting window
2 ZOOM (T/W) buttons Zoom in and out (Z pg. 17) —
3 PLAY button — Playback start (Z pg. 38)
4 STOP button — Stop (Z pg. 38)
5 REW button Retake (Rewind) (Z pg. 18)/ Rew/Rew Shuttle Search (Z pg. 38)
6 INSERT button — Insert Editing (Z pg. 44)
7 START/STOP button Functions same as the Recording Start/Stop button of the camcorder.
8 INT. TIME button Self-Timer(Z pg. 34)/Time Lapse (Z pg. 35) —
9 REC TIME button Animation/Time lapse (Z pg. 35) —
0 PAUSE button — Pause/Play (during Pause mode) (Z pg. 38)
! FF button Retake (Forward) (Z pg. 18) FF/FF Shuttle Search (Z pg. 38)
@ A. DUB button — Audio dubbing (Z pg. 45)
9
0
A
!
@
Functions
With the camcorder’s power switch With the camcorder’s power switch set
set to “CAMERA”. to “PLAY”.
Quick Review (Z pg. 17)
16
POWER
Start/Stop
The power indicator
LENS COVER
SWITCH
RECORDING
Basic Recording
NOTE:
You should already have performed the procedures listed
below. If not, do so before continuing.
●
Power (Z pg. 8)
●
Tape Length (Z pg. 12)
●
Recording Mode Setting (Z pg. 13)
●
Grip Adjustment (Z pg. 14)
LOAD A CASSETTE
Slide EJECT to open the cassette holder, then insert
1
the cassette with the label facing out. Press PUSH to
ensure the holder is closed and locked.
ENTER RECORD–STANDBY MODE
Slide the LENS COVER open/close switch to open
2
the lens cover, then set the power switch to
“CAMERA”.
•The power indicator lights and the camcorder
enters the Record–Standby Mode.
•The scene you’re aimed at appears on the
viewfinder screen, with the word “PAUSE”
superimposed upon it.
25min
Tape remaining time indicator
120min 119min
1min (Blinking)
0min (Blinking)
* min.....(Now calculating)
2min (Blinking)
Tally lamp
3min
START SHOOTING
Press the RECORDING START/STOP button.
3
•The tally lamp lights while recording is in progress,
REC
and “
•If you want to turn the tally lamp off, see page 31.
STOP RECORDING
Press the RECORDING START/STOP button again to
4
stop recording.
•The camcorder re-enters the Record-Standby
mode.
” appears in the viewfinder.
NOTES:
●
A cassette holder can’t be opened unless a power supply is attached.
●
There may be a delay after you slide EJECT until the holder opens. Do not use force.
●
The tape’s remaining time is displayed in the viewfinder as shown.
●
The indicated remaining time is approximate.
●
The time required to calculate the remaining tape length, and the accuracy of the calculation, may vary
according to the type of tape used.
●
The tape remaining time displayed in the viewfinder is correct only if the correct tape length has been
selected (Z pg. 12).
●
“TAPE END” appears when the tape reaches its end, and the power goes off automatically if left in this
condition for 5 minutes. “TAPE END” also appears when a cassette whose tape is already at its end is
loaded.
●
If the Record–Standby mode continues for 5 minutes without performing Zoom or any other operations,
the camcorder’s power shuts off automatically. Set the Power switch to “POWER OFF”, and then back to
“CAMERA” to turn the camcorder on again.
●
If you’re recording on a cassette from the middle, use the RETAKE function (Z pg. 18) to find the end of
the last recording so you don’t erase any of it.
●
The LENS COVER warning blinks for about 8 seconds when the camcorder is turned on, when the cover is
closed.
RECORDING
Zoom-in
W
T
Main Menu
screen
W
T
Zoom-out
Zoom indicator bar
W
Shooting mode selector
FAR
+
NEAR
–
Power zoom lever
Shift Zoom l50x
Tele Macro OFF
Gain Up AGC
Color Filter NOR.
Tape Length T30
Title
Date/Time
Sub Menu
Basic Features
W
Zoom level
indicator
T
W
T
FEATURE: Zooming
PURPOSE: To produce the zoom in/out effect, or
an instantaneous change in image
magnification.
OPERATION: 28X Hyper zoom
T
Digital circuitry doubles the
maximum 14x magnification offered
by optical zoom.
1) To zoom in, slide the Zoom Lever
toward “T”.
2) To zoom out, slide toward “W”.
Shift Zoom
By digitally processing and magnifying images, zooming is possible from
5 – 14 times the optical zoom limit,
to a maximum of 140x magnification.
1) Set the Shooting Mode Selector to
“PRESET” and press MENU to
access the Main Menu screen.
2) Press + or – to move the highlight
bar to “Shift Zoom.”
3) Press FAR or NEAR to set the
magnification. “50x” magnifies
wide-angle images to
approximately 3.6 times the
original size, and enables zooming
in the 18x – 50x range. “140x”
magnifies wide-angle images to
approximately 10 times the
original size, and allows zooming
from 50x to 140x. To disable Shift
Zoom, set it to “OFF”. “140x” is
useful when you want to confirm
letters or numbers from a distance.
4) Press MENU to close the Main
Menu screen.
NOTES:
●
During Hyper Zoom, the speed
increases the further you slide the
Zoom Lever.
●
Focusing may be come unstable
during Hyper Zoom. In this case,
set the zoom while in Record –
Standby, set manual focus or Focus
Lock (Z pg. 24, 25), then zoom in
or out in Record mode.
●
The Zoom Level Indicator (5) only
moves during optical zoom. Once
the indicator reaches “T”, all
magnification from that point is
through digital processing.
●
During digital image processing,
the quality of the image may suffer.
FEATURE: Quick Review
PURPOSE: To check the end of the last
recording.
OPERATION: 1) Press “
” and release quickly
during the Record–Standby mode.
• Tape is rewound for about 2 seconds
and played back automati-cally, then
pauses in Record–Standby mode for
NOTE:
the next shot.
Distortion may occur at start of
playback.
This is normal.
17
18
START/STOP
VISS
RM-V700U (optional)
RETAKE
Record-Standby
Normal Upside down
Record
AUTO PAUSE
Up
Record-Standby
RECORDING
FEATURE: Index Code Marking
PURPOSE: To give you automatic access to any
OPERATION:
NOTE: ●
FEATURE: Retake
PURPOSE: To re-record certain segments.
OPERATION: 1) Make sure the camcorder is in the
NOTE: ●
FEATURE: Auto Pause System
PURPOSE: To automatically stop recording
OPERATION: 1) Set AUTO PAUSE to “ON”. When
NOTE: ●
Basic Features (cont.)
selected point on a recording. Auto
Marking and Manual Marking are
available.
Auto Marking
An index code is marked to start the
first recording after a cassette is
inserted, as long as the Power switch
is set to “CAMERA”.
Manual Marking
1) Press VISS once to place the index
code. INDEX blinks in the
viewfinder during marking.
If VISS is pressed during
Record–Standby mode, the mark is
placed where RECORDING
START/STOP is pressed.
Record–Standby mode.
2) Press either RETAKE button to
reach the start point for new
recording.
3) Press RECORDING START/STOP
to start recording.
Noise may appear during Retake.
This is normal.
when the camcorder is pointed
down, preventing accidental
recordings of the ground, your feet,
etc.
the camcorder is tilted down by a
large degree from its horizontal
position during recording, the
Record-Standby mode is
automatically engaged. “AUTO
PAUSE” appears in the viewfinder.
The Auto Pause System is also
effective when the camcorder is
pointed up, or is positioned upside
down.
●
Auto Pause also works when the
camcorder is twisted by a large
degree to the left or right.
●
When you want to shoot in any of
the aforementioned positions,
make sure you set AUTO PAUSE to
“OFF”.
Record-Standby
Down
Loading...