JVC GR-AX237UM, GR-AX437UM, GR-AX537UM, GR-AX837EG, GR-AX837UM Instructions Manual

ENGLISHPORTUGUÊS ESPAÑOL

LYT0002-079A

GR-AX837/GR-AX537
GR-AX437/GR-AX237

COMP ACT VHS CAMCORDER

VIDEOCAMARA VHS COMPACTO
CÂMERA VHS COMPACTA

INSTRUCTIONS

MANUAL DE INSTRUCCIONES

INSTRUÇÕES

Compact VHS



(GR-AX837/AX537 shown.)

EN 3

ANTENNA INSTALLATION
INSTRUCTIONS

1. Outdoor Antenna Grounding

If an outside antenna or cable system is connected
to the product, be sure the antenna or cable system
is grounded so as to provide some protection
against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/
NFPA 70, provides information with regard to
proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding conduc­tors, location of antenna discharge unit, connection
to grounding electrodes, and
requirements for the grounding electrode.

2. Lightning

For added protection for this product during a
lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the
wall outlet and disconnect the antenna or cable
system. This will prevent damage to the product
due to lightning and power-line surges.

3. Power Lines

An outside antenna system should not be located in
the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall
into such power lines or circuits. When installing an
outside antenna system, extreme care should be
taken to keep from touching such power lines or
circuits as contact with them might be fatal.

IMPORTANT PRODUCT
SAFETY INSTRUCTIONS

Electrical energy can perform many useful functions. But
improper use can result in potential electrical shock or fire
hazards. This product has been engineered and
manufactured to assure your personal safety. In order not to
defeat the built-in safeguards, observe the following basic
rules for its installation, use and servicing.

ATTENTION:

Follow and obey all warnings and instructions marked on
your product and its operating instructions. For your safety,
please read all the safety and operating instructions before
you operate this product and keep this manual for future

reference.

INSTALLATION

1. Power Sources

Operate your product only from the type of power
source indicated on the marking label. If you are
not sure of the type of power supply to your home,
consult your product dealer or local power
company. If your product is intended to operate
from battery power, or other sources, refer to the
operating instructions.

2. Overloading

Do not overload wall outlets, extension cords, or
integral convenience receptacles as this can result
in a risk of fire or electric shock.

3. Power Cord Protection

Power supply cords should be routed so that they
are not likely to be walked on or pinched by items
placed upon or against them, paying particular
attention to cords at plugs, convenience recepta­cles, and the point where they exit from the
product.

4. Ventilation

Slots and openings in the cabinet are provided for
ventilation. To ensure reliable operation of the
product and to protect it from overheating, these
openings must not be blocked or covered.

•Do not block the openings by placing the product
on a bed, sofa, rug or other similar surface.

•Do not place the product in a built-in installation
such as a bookcase or rack unless proper
ventilation is provided or the manufacturer’s
instructions have been adhered to.

5. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling
only as recommended by the manufacturer.

ANTENNA
LEAD IN WIRE

ANTENNA
DISCHARGE UNIT
(NEC SECTION 
810-20)

GROUNDING 
CONDUCTORS
(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM
(NEC ART 250. PART H)

NEC – NATIONAL ELECTRICAL CODE

ELECTRIC SERVICE
EQUIPMENT

EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70

GROUND CLAMP

4 EN

USE

1. Accessories

To avoid personal injury:

• Do not place this product on an unstable cart, stand,
tripod, bracket or table. It may fall, causing serious injury
to a child or adult, and serious damage to the product.

• Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer or sold with the
product.

• Use a mounting accessory recommended by the
manufacturer and follow the manufacturer’s instructions
for any mounting of the product.

• Do not try to roll a cart with small casters across
thresholds or deep-pile carpets.

2. Product and Cart Combination

A product and cart combination should be moved with
care. Quick stops, excessive force, and uneven surfaces
may cause the product and cart combination to overturn.

3. Water and Moisture

Do not use this product near
water—for example, near a bath
tub, wash bowl, kitchen sink or
laundry tub, in a wet basement, or
near a swimming pool and the
like.

4. Object and Liquid Entry

Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock.

Never spill liquid of any kind on the product.

5. Attachments

Do not use attachments not recommended by the
manufacturer of this product as they may cause hazards.

6. Cleaning

Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a damp
cloth for cleaning.

7. Heat

The product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.

SERVICING

1. Servicing

If your product is not operating correctly or exhibits a
marked change in performance and you are unable to
restore normal operation by following the detailed
procedure in its operating instructions, do not attempt to
service it yourself as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all

servicing to qualified service personnel.

2. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing
to qualified service personnel under the following
conditions:

a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the

product.

c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following

the operating instructions. Adjust only those controls that
are covered by the operating instructions as an improper
adjustment of other controls may result in damage and
will often require extensive work by a qualified
technician to restore the product to its normal operation.

e. If the product has been dropped or damaged in any way.
f. When the product exhibits a distinct change in

performance—this indicates a need for service.

3. Replacement Parts

When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer or have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock or other hazards.

4. Safety Check

Upon completion of any service or repairs to this product,
ask the service technician to perform safety checks to
determine that the product is in safe operating condition.

PORTABLE CART WARNING
(Symbol provided by RETAC)

EN 5

QUICK OPERATION GUIDE

SUPPLY POWER

Using the battery pack

1

Hook-on the battery pack’s top end to the
camcorder. (Charging procedure, Z pg. 8)

2 Push in the battery pack until it locks into

place.

To remove the battery pack

Slide BATT. RELEASE and pull out the battery
pack.

PLAYBACK

1 Set the power switch to “PLAY”.
2 Press REW.

— The tape will automatically stop at the

beginning of the tape.

3 Press PLAY/PAUSE.

— Playback starts and the playback picture

appears in the viewfinder.

•To stop playback, press STOP.

(For more details, Z pg. 32.)

n

Or simply play back the tape on a VHS
VCR using the Cassette Adapter
(VHS Playpak). Z pg. 30

SHOOTING

1 Slide the LENS COVER open/close knob to

open the lens cover.

2 Set the power switch to “CAMERA”.

— The power indicator will light and an

image will appear in the viewfinder.

3 Press the Recording Start/Stop button.

— Recording starts.

•To stop recording temporarily, momentarily
press the Recording Start/Stop button once
again.
(For more details, Z pg. 14)

INSERTING A VIDEO CASSETTE

1 Slide EJECT.
2 Insert a video cassette.
3 Press PUSH.

(For more details, Z pg. 12)

2

Push in.

Hook on.

1

1

Set to “PLAY”

3

PLAY/PAUSE

2

REW

STOP

BATT. RELEASE

1

LENS COVER
open/close knob

2

Set to “CAMERA”

3

Recording Start/Stop button

1

EJECT

Insert.

2

PUSH

3

6 EN

MAJOR FEATURES

REMEMBER

The Logical Choice

The only compact video

cassettes that can be

used with your VHS VCR*

Program AE with Special
Effects (

Z pg. 18)

n Auto Mode Lock n Auto Mode Release
n Electronic Fog Filter n ND Effect
n Sepia n Twilight n Sports
n 1/1000 sec. High Speed Shutter
n 1/2000 sec. High Speed Shutter

Program Manager
(

Z pg. 18 – 29)

Program AE with Special Effects, Exposure
Control, Focus, Fader, Wide, Instant Title,
Date/Time Character Insert, White
Balance Adjustment, Menu Adjustment

Random Assemble Editing
(

Z pg. 35 – 37)

8

8

2

2

554

4

11663

3

7

7

Variable-Speed Hyper Zoom
(

Z pg. 15)

Zoom-in

Zoom-out

Integrated Auto Light
(GR-AX837/AX537 only)
(

Z pg. 17)

PROVIDED ACCESSORIES

•Remote Control
Unit RM-V705U
(GR-AX837 only)

•DC Cord

•AC Power Adapter/
Charger AA-V11EG

•Battery Pack
BN-V11U

•Cassette Adapter
(VHS PlayPak)
C-P7U

•Shoulder Strap

•Lithium Battery CR2025

•x2 for GR-AX837 (clock operation and remote

control unit)

•x1 for GR-AX537/AX437/AX237 (clock operation)

Cassettes marked can be used with this camcorder.

EN 7

CONTENTS

GETTING STARTED

8

Power............................................................................................... 8

Clock (Lithium) Battery Insertion/Removal................................................. 10

Viewfinder Adjustment ........................................................................ 10

Date/Time Setting ............................................................................. 11

Tape Length Setting ............................................................................ 12

Recording Mode Setting ....................................................................... 12

Loading/Unloading A Cassette ............................................................... 12

Grip Adjustment ................................................................................ 13

Shoulder Strap Attachment.................................................................... 13

Tripod Mounting ................................................................................ 13

RECORDING

14

Basic Recording ................................................................................. 14

Basic Features................................................................................... 15

Advanced Features ............................................................................. 18

PLAYBACK

30

Using The Cassette Adapter................................................................... 30

Basic Connections............................................................................... 31

Basic Playback .................................................................................. 32

Features ......................................................................................... 33

EDITING

34

Tape Dubbing.................................................................................... 34

Random Assemble Editing (R.A.Edit)......................................................... 35

USING REMOTE CONTROL UNIT (GR-AX837 only)

38

Insert Editing.................................................................................... 40

Audio Dubbing .................................................................................. 41

USER MAINTENANCE

42

TROUBLESHOOTING

43

INDEX

45

Viewfinder ...................................................................................... 45

Controls.......................................................................................... 46

Connectors....................................................................................... 47

Indicators ........................................................................................ 47

Other Parts...................................................................................... 47

Terms ............................................................................................. 48

CAUTIONS

49

SPECIFICATIONS

51

OPTIONAL ACCESSORIES

51

8 EN

GETTING STARTED

Power

This camcorder’s 3-way power supply system lets you
choose the most appropriate source of power.

NOTES:

●

No function is available without power supply.

●

Use only specified power supply.

●

Do not use provided power supply units with other equipment.

CHARGING THE BATTERY PACK

SUPPLY POWER

1

Connect the charger’s AC power cord to a wall
outlet. The power indicator lights.

ATTACH BATTERY PACK

2

Align the marks and slide the battery pack in the
direction of the arrow until it locks in place.
The CHG. indicator lights.

DETACH BATTERY PACK

3

When charging is completed, the END indicator
lights. Slide the battery pack opposite the direction
of the arrow.

BATT. PACK CHARGE DISCHARGE

BN-V11U approx. 1 hr. 10 min. approx. 3 hrs. 30 min.
BN-V12U approx. 1 hr. 10 min. approx. 3 hrs. 30 min.
BN-V22U approx. 2 hrs. 10 min. approx. 7 hrs.
BN-V25U approx. 2 hrs. 40 min. approx. 10 hrs.

REFRESH indicatorREFRESH switch

CHG. (charge) indicator

To AC outlet

Marks

END
indicator

POWER
indicator

Hook on.

Push in.

BATT. RELEASE

** CHARGE MARKER

A charge marker is provided on
the battery pack to help you
remember whether it has been
charged or not. Two colors are
provided (red and black)—you
choose which one means
charged and which means
discharged.

APPROXIMATE RECORDING TIME

BATT. PACK GR-AX837/AX537/AX437 GR-AX237

BN-V11U 1 hr. 10 min. (40 min.) 1 hr. 10 min.
BN-V12U 1 hr. 10 min. (40 min.) 1 hr. 10 min.
BN-V22U 2 hrs. 20 min. (1hr. 25 min.) 2 hrs. 25 min.
BN-V25U 3 hrs. 5 min. (1hr. 55 min.) 3 hrs. 10 min.

USING THE BATTERY PACK

ATTACH BATTERY PACK

1

Hook its top end to the camcorder and push the
battery pack in until it locks in place.

DETACH BATTERY PACK

2

Slide BATT. RELEASE and pull out the battery pack.

( ): when the video light is on (GR-AX837/AX537 only).

**REFRESH

The AC power adapter features a REFRESH function that allows
you to fully discharge the battery pack before recharging.

To discharge the battery . . .

...... attach the battery pack to the adapter as shown in the

illustration to the left. Then push REFRESH. The REFRESH
indicator lights when discharging starts, and goes out when
discharging is complete.

ATTENTION:

Before detaching the power source,
make sure that the camcorder’s power
is turned off. Failure to do so can result
in a camcorder malfunction.

Charge marker

EN 9

NOTES:

●

The recording time per charge is affected by such factors as the time spent in Record/Standby mode and
the frequency of zooming. It is safer to have spare battery packs.

●

Charging times noted on page 8 are for fully discharged battey pack, and discharging times are for fully
charged battery pack.

●

Charging and discharging times vary according to the ambient temperature and the status of the battery pack.

●

Remember to set the charge marker after charging a battery pack or after detaching a discharged one from
your camcorder.

●

Perform the REFRESH function after no less than 5 chargings.

●

High temperatures can damage the battery pack, so use only where good ventilation is available. Don’t
allow it to discharge in container, such as a bag.

●

If you stop recharging or discharging part way through, make sure to remove the battery pack before
unplugging the adapter’s AC cord.

●

Remove the battery pack from the adapter immediately after discharging.

●

To avoid interference with reception, do not use the AC Power Adapter/Charger near a radio.

●

Make sure you unplug the DC cord before charging or discharging the battery pack.

●

A blinking CHG. indicator means that the battery pack has become hot. Wait until it cools down to continue.

●

The CHG. indicator may not light properly with a brand new battery pack, or with one that’s been stored
for an extended period. In this case, remove and reattach the battery pack and recharge it. The CHG.
indicator should light during recharging. If not, contact your nearest JVC dealer.

USING A CAR BATTERY

Use the optional Car Battery Cord or Car Battery
Charger/Adapter (connect as shown in the
illustration to the left).

NOTES:

●

When using the car battery, leave the engine
idling.

●

The optional Car Battery Charger (BH-V3U) can
also be used to charge the battery pack.

●

When using the optional Car Battery Charger or
Car Battery Cord (AP-V7U), refer to the respective
instruction booklet.

USING AC POWER

Use the AC Power Adapter (connect as shown in
the illustration to the left).

NOTE:

The supplied AC Power Adapter/Charger features
automatic voltage selection in the AC range from
110 V to 240 V.

To AC outlet

To D C
in jack

AC Power
Adapter/Charger
AA-V11EG (provided)

To car’s
cigarette
lighter
socket

Car Battery Cord
AP-V7U (optional)

Car Battery Charger/Adapter
BH-V3U (optional)

DC OUT
terminal

DC cord

10 EN

GETTING STARTED

(cont.)

Clock (Lithium) Battery Insertion/Removal

This battery is necessary for clock operation and to
perform date/time settings.

SWITCH OFF POWER

1

Switch off the unit’s power and remove the power
supply unit.

OPEN COVER

2

Open the clock battery compartment cover while
pressing the release tab.

REMOVE BATTERY (when replacing)

3

Insert a pointed, non-metallic object between the
battery and the compartment (A) and pull the
battery out.

INSERT BATTERY

4

Ensuring the plus (+) side is up, insert a CR2025
lithium battery and push it in.

CLOSE COVER

5

Close the compartment cover until it clicks in place.

NOTE:

See “SAFETY PRECAUTIONS” (Z pg. 2) for information
on safe handling of lithium batteries.

Viewfinder Adjustment

POSITION VIEWFINDER

1

Adjust the viewfinder manually for best viewability
(see illustration at left).

SELECT MODE

2

Set the power switch to CAMERA.

ADJUST DIOPTER

3

Turn the diopter adjustment control until the
indications in the viewfinder are clearly focused.

A

1

2

3

Set POWER to “CAMERA”.

EN 11

SET
CANCEL



JAN 1.00 AM 12:00

GAIN UP S.LX
TELE MACRO OFF
INTERVAL TIMER OFF
REC TIME OFF
JLIP ID NO. 07
SET CHARACTER 

DATE/TIME 

END :MENU KEY

+

–

Date/Time Setting

SELECT MODE

1

First set the power switch to “CAMERA”. Turn the
PROGRAM AE select dial to any position except
AUTO LOCK.

ACCESS MENU SCREEN

2

Press MENU.

SELECT FUNCTION

3

Press – to move the highlight bar down to “DATE/
TIME”, then press NEAR. The Set Date And Time
screen appears.

SET DATE/TIME

4

Press FAR or NEAR until the item you want to set
begins blinking, then press + or – to until the correct
setting appears.

•If you decide you want to return the date and time

to the previous settings, press FAR or NEAR to
move the highlight bar to “CANCEL”, then press
MENU.

•If you’re satisfied with the settings, go on to step 5.

START CLOCK OPERATION

5

Once you’ve set the month, day, year and time,
press FAR or NEAR until “SET” begins to blink, then
press MENU. The Menu screen reappears.

CLOSE MENU

6

Press MENU.

NOTES:

●

To display the date and time in the viewfinder and on a
connected TV, see “Date/Time Insert” (Z pg. 24).

●

If, in step 4, you input an invalid date (FEB 30, JUN 31,
etc.) and perform step 5, “INPUT ERROR” appears
blinking at the bottom of the screen. Press +, –, FAR or

NEAR to input the correct number.

PROGRAM AE
select dial

NEAR

Set Time and
Date Screen

Time

12-hour indication with
AM or PM

Date

Month/Day/Year

Menu Screen

FAR

MENU

12 EN

SP

EP

SP

T30

T20

T30 T40

GETTING STARTED

(cont.)

Tape Length Setting

Set the tape length according to the length of the tape
used.

SET TAPE LENGTH

1

Press T20•30•40 until the required indication
appears in the veiwfinder. T20 = 20 minutes of
recording time, T30 = 30 minutes, and T40 = 40
minutes (in SP).

NOTE:

The tape remaining time (Z pg. 14) displayed in the
viewfinder is correct only if the correct tape length has
been selected.

Recording Mode Setting

Set depending on your preference.

SET RECORDING MODE

1

Press SP-EP button. “SP” (Standard Play) provides
higher picture and sound quality and is better for
dubbing, while “EP” (Extended Play) is more
economical, recording at 1/3 the speed of SP.

NOTE:

If the recording mode is switched during recording, the
playback picture will be blurred at the switching point.

Loading/Unloading A Cassette

OPEN CASSETTE HOLDER

1

Slide EJECT until the holder opens. Do not use force
to open.

INSERT/REMOVE CASSETTE

2

Make sure the label is facing outward.

CLOSE CASSETTE HOLDER

3

Press PUSH and make sure the holder is closed and
locked.

NOTES:

●

A cassette holder can’t be opened unless a power
supply is attached.

●

Make sure that the tape is not slack when loading the
cassette. If there is any slack, turn the gear on the
cassette in the direction of the arrow to take up the
slack.

●

Make sure the Erase Protection tab is in the position
that allows recording. If not, slide the tab. Some
cassettes have removable tabs. If the tab has been
removed, cover the hole with adhesive tape.

●

The cassette holder can’t be opened while the
camcorder is in the record mode.

Set POWER to “CAMERA”.

SP-EP recording mode button

Tape length indicator

Recording mode indicator

Turn to take
up slack.

GearErase Protection

T20•30•40 tape
length select button

EN 13

Grip Adjustment

EXPAND LOOP

1

Separate the Velcro strip.

INSERT HAND

2

Pass your right hand through the loop and grasp the
grip.

ADJUST STRAP LENGTH

3

Adjust so your thumb and fingers can easily operate
the Recording Start/Stop button and Power Zoom
lever. Refasten the Velcro strip.

Shoulder Strap Attachment

ATTACH STRAP

1

Following the illustration at left, thread the strap
through the top of the eyelet 1, then fold it back
and thread it through the keeper 2, and then
through the buckle 3. Repeat the procedure to
attach the other end of the strap to the other eyelet,
making sure the strap isn’t twisted.

ADJUST LENGTH

2

Adjust as shown in the illustration at left 1, then
slide both keepers snug against the eyelets to
prevent slipping 2.

Tripod Mounting

ALIGN AND TIGHTEN

1

Align the screw and camera direction stud on the
tripod with the camera’s mounting socket and stud
hole. Then tighten the screw.

2

3

1

2

1

Recording Start/Stop button

14 EN

25MIN

120MIN
119MIN

3MIN
2MIN (Blinking)
1MIN (Blinking)
0MIN (Blinking)

*-

-

-MIN

(Now calculating)

RECORDING

Basic Recording

NOTE:

You should already have performed the procedures listed
below. If not, do so before continuing.

●

Power (Z pg. 8)

●

Tape Length setting (Z pg. 12)

●

Recording Mode Setting (Z pg. 12)

●

Grip Adjustment (Z pg. 13)

LOAD A CASSETTE

1

Slide EJECT to open the cassette holder, then insert
the cassette with the label facing out. Press PUSH to
ensure the holder is closed and locked.

ENTER RECORD–STANDBY MODE

2

Slide the LENS COVER open/close switch to open
the lens cover, then set the power switch to
“CAMERA”.

•The power indicator lights and the camcorder
enters the Record–Standby Mode.

•The scene you’re aimed at appears on the
viewfinder screen, with the word “PAUSE”
superimposed upon it.

START SHOOTING

3

Press the RECORDING START/STOP button.

•The tally lamp lights while recording is in progress,
and “

REC

” appears in the viewfinder.

STOP RECORDING

4

Press the RECORDING START/STOP button again to
stop recording.

•The camcorder re-enters the Record-Standby
mode.

NOTES:

●

A cassette holder can’t be opened unless a power supply is attached.

●

There may be a delay after you slide EJECT until the holder opens. Do not use force.

●

The tape’s remaining time is displayed in the viewfinder as shown.

●

The indicated remaining time is approximate.

●

The time required to calculate the remaining tape length, and the accuracy of the calculation, may vary
according to the type of tape used.

●

The tape remaining time displayed in the viewfinder is correct only if the correct tape length has been
selected (Z pg. 12).

●

“TAPE END” appears when the tape reaches its end, and the power goes off automatically if left in this
condition for 5 minutes. “TAPE END” also appears when a cassette whose tape is already at its end is
loaded.

●

If the Record–Standby mode continues for 5 minutes without performing Zoom or any other operations,
the camcorder’s power shuts off automatically. Set the Power switch to “POWER OFF”, and then back to
“CAMERA” to turn the camcorder on again.

●

If the Recording Start/Stop button is pressed after the Record-Standby mode has continued for over 5
minutes, recording may not start immediately.

●

If you’re recording on a cassette from the middle, use the RETAKE function (Z pg. 16) to find the end of
the last recording so you don’t erase any of it.

●

The LENS COVER warning blinks for about 10 seconds when the camcorder is turned on, when the cover
is closed.

Tape remaining time indicator

POWER

Power indicator

Start/Stop button

LENS COVER
switch

Tally lamp

EN 15

FEATURE: Zooming
PURPOSE: Varies the focal length of the lens

and produces the zoom in/out effect.

OPERATION:

Zoom In

1) Push the power zoom switch

down toward “T”.

Zoom Out

1) Push the switch up toward “W”.

NOTES: ●

The further the power zoom switch
is pushed, the faster the zoom
speed becomes.

●

Focusing may become unstable
during zooming. In this case, set
the zoom while in Record–
Standby, set manual focus or Focus
Lock (Z pgs. 20, 21), then zoom

in or out in Record mode.

RECORDING

Basic Features

Zoom indicator

Power zoom switch

Zoom-in

Zoom-out

16 EN

RECORDING

Basic Features (cont.)

FEATURE: Quick Review
PURPOSE: To check the end of the last record-

ing.

OPERATION: 1) Press “ ” and release quickly

during the Record–Standby mode.

•Tape is rewound for about 2
seconds and played back
automatically, then pauses in
Record–Standby mode for the
next shot.

NOTE:

Distortion may occur at start of
playback. This is normal.

FEATURE: Retake
PURPOSE: To re-record certain segments.
OPERATION: 1) Make sure the camcorder is in the

Record–Standby mode.

2) Press either RETAKE button to

reach the start point for new
recording.
Pressing “F” fast-forwards the tape
and pressing “R” reverses it.

3) Press Recording Start/Stop to start

recording.

NOTE:

Noise may appear during Retake.
This is normal.

RETAKE (R/F)