JVC GR-AX761 User Manual

COMPACT
VHS CAMCORDER

GR-AXM231
GR-AX761

INSTRUCTIONS

For Customer Use:

Enter below the Model No. and Serial No. which is located on the
bottom of cabinet. Retain this information for future reference.

Model No.

ENGLISH

CONTENTS

SAFETY PRECAUTIONS
AUTOMATIC DEMONSTRATION
PROVIDED ACCESSORIES

GETTING STARTED
RECORDING

Basic Recording .......................... 14

Basic Features ........................... 16

Zooming, Picture Stabilizer, Quick Review,
Retake, 5-Sec. Recording, Video Light

Advanced Features ...................... 19

Fade/Wipe Effects,
Program AE With Special Effects,
Digital Effects, Using Menus For Detailed
Adjustment, Date/Time Insert, Instant Titles,
Animation, Time-Lapse, Exposure Control,
Focusing, White Balance Adjustment,
Manual White Balance Operation

PLAYBACK

Basic Playback ........................... 30

Features .................................. 31

Connections And Tape Dubbing ........32

Using The Cassette Adapter ........... 34

USING THE REMOTE CONTROL
UNIT (GR-AX761 only)

Animation And Time-Lapse ............. 37

Insert Editing .............................38

Audio Dubbing ........................... 39

TROUBLESHOOTING
DETAILS
INDEX

Terms ...................................... 43

Controls, Connectors And Indicators ... 44

Indications ................................ 46

CAUTIONS
SPECIFICATIONS
ESPAÑOL
FOR SERVICING (Only in U.S.A.)
WARRANTY (Only in U.S.A.)

2 – 3

6 – 13

14 – 29

30 – 34

35 – 39

40 – 41

43 – 47

48 – 50

52 – 53

4

4

42

51

54

55

Serial No.

LYT0690-001B

EN

2 EN

Dear Customer,

Thank you for purchasing the JVC Compact VHS camcorder. Before use, please read the safety information
and precautions contained in the following pages to ensure safe use of this product.

Using This Instruction Manual

•All major sections and subsections are listed in the Table Of Contents on the cover.

•Notes appear after most subsections. Be sure to read these as well.

•Basic and advanced features/operation are separated for easier reference.

It is recommended that you . . .

.... refer to the Index (墌 pgs. 43 – 47) and familiarize yourself with button locations, etc. before use.

.... read thoroughly the Safety Precautions and Safety Instructions that follow. They contain extremely

important information regarding the safe use of this product.

You are recommended to carefully read the cautions on pages 48 – 50 before use.

SAFETY PRECAUTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.

CAUTIONS:

● This camcorder is designed to be used with NTSC-type color television signals. It cannot be used for

playback with a television of a different standard. However, live recording and LCD monitor*/viewfinder
playback are possible anywhere.

● Use the JVC BN-V11U**/V12U/V20U/V400U battery packs and, to recharge them or to supply power to

the camcorder from an AC outlet, use the provided multi-voltage AC Adapter. (An appropriate conversion
adapter may be necessary to accommodate different designs of AC outlets in different countries.)

* GR-AXM231 only.
**GR-AX761 only.

ATTENTION:

The product that you have purchased is powered by a rechargeable battery. The battery is recyclable. At
the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into
the municipal waste stream. Check with your local solid waste officials for details in your area for
recycling options or proper disposal.

WARNING:
TO REDUCE THE RISK OF FIRE

OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS APPARATUS
TO RAIN OR MOISTURE.

NOTES:

●

The rating plate (serial number plate) and safety
caution are on the bottom and/or the back of
the main unit.

●

The rating information and safety caution of the
AC Adapter are on its upper and lower sides.

Cassettes marked can be used with this camcorder.

EN3

The EPA certified RBRC® Battery Recycling Seal on the nickel-cadmium (Ni-Cd) battery indicates JVC is
voluntarily participating in an industry program to collect and recycle these batteries at the end of their
useful life, when taken out of service in the United States. The RBRC® program provides a convenient
alternative to placing used Ni-Cd batteries into the trash or the municipal waste stream, which may be
illegal in your area. Please call 1-800-8-BATTERY™ for information on Ni-Cd battery recycling and
disposal bans/restrictions in your area. JVC’s involvement in this program is part of our commitment to
preserving our environment and conserving our natural resources.

When the equipment is installed in a cabinet or on a shelf, make sure that it has sufficient space on all
sides to allow for ventilation (10 cm (3-15/16") or more on both sides, on top and at the rear).

Do not block the ventilation holes.
(If the ventilation holes are blocked by a newspaper, or cloth etc. the heat may not be able to get out.)

No naked flame sources, such as lighted candles, should be placed on the apparatus.

When discarding batteries, environmental problems must be considered and the local rules or laws
governing the disposal of these batteries must be followed strictly.

The apparatus shall not be exposed to dripping or splashing.

Do not use this equipment in a bathroom or places with water.
Also do not place any containers filled with water or liquids (such as cosmetics or medicines, flower vases,
potted plants, cups etc.) on top of this unit.
(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)

IMPORTANT SAFETY INSTRUCTIONS

(1) Read these instructions.

(2) Keep these instructions.

(3) Heed all warnings.

(4) Follow all instructions.

(5) Do not use this apparatus near water.

(6) Clean only with dry cloth.

(7) Do not block any ventilation openings.

Install in accordance with the
manufacturer’s instructions.

(8) Do not install near any heat sources such

as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that
produce heat.

(9) Only use attachments/accessories specified

by the manufacturer.

(10) Use only with the cart,

stand, tripod, bracket, or
table specified by the
manufacturer, or sold with
the apparatus. When a
cart is used, use caution
when moving the cart/
apparatus combination to avoid injury from
tip-over.

(11) Unplug this apparatus during lightning

storms or when unused for long periods of
time.

(12) Refer all servicing to qualified service

personnel. Servicing is required when the
apparatus has been damaged in any way,
such as power-supply cord or plug is
damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does
not operate normally, or has been dropped.

4 EN

O

O

E

F

N

XFIT

DEMO MODE

AUTOMATIC DEMONSTRATION

Automatic Demonstration takes place when “DEMO MODE” is set to “ON”
(factory-preset).

䡲

Available when the Power Switch is set to “ ” or “ ”.

䡲

Operating the Power Zoom Lever during the demonstration stops the
demonstration temporarily. If the Power Zoom Lever is not moved for
more than 1 minute after that, the demonstration will resume.

䡲

“DEMO MODE” remains “ON” even if the camcorder power is turned
off.

䡲

To cancel Automatic Demonstration, set the Power Switch to “ ” and
press the MENU Wheel in while the demo is in progress. This takes you
directly to the demo mode’s Setting Menu (so you will not have to go
through the main Menu Screen). Rotate the MENU Wheel to select
“OFF” and press it.

NOTES:

●

When a tape whose Erase Protection tab is in the position that allows recording is loaded in the
camcorder, demonstration is not available.

●

If you do not detach the Lens Cap, you cannot see the actual changes of the Automatic Demonstration
activated on the LCD monitor or viewfinder.

PROVIDED ACCESSORIES

Setting Menu

•AC Adapter
AP-V10U

•Battery Pack
BN-V11U
(GR-AX761 only)
BN-V20U
(GR-AXM231 only)

•Shoulder Strap

•Lens Cap

•Cassette Adapter

(VHS Playpak) C-P7U

•Remote Control Unit
RM-V715U
(GR-AX761 only)

•AAA (R03) Battery x 2
(for Remote Control Unit,
GR-AX761 only)

•AA (R6) Battery
(for Cassette Adapter)

How To Attach The Lens Cap

To protect the lens, attach the provided lens cap to the camcorder as shown in the illustration.

132

EN5

6 EN

Hook on.

1

BATTERY RELEASE Switch

REFRESH Button

REFRESH Lamp

CHARGE Lamp

2

Push in.

GETTING STARTED

Power

This camcorder’s 2-way power supply system lets you
choose the most appropriate source of power. Do not use
provided power supply units with other equipment.

CHARGING THE BATTERY PACK

Make sure the battery pack is attached to the

1

camcorder. Hook its end to the camcorder 1 and
push the battery in until it locks in place 2.

•If the battery pack is attached in the wrong position,
a malfunction may occur.

Set the Power Switch to “OFF”. Connect the AC

2

Adapter to the camcorder 3.

Plug the AC Adapter into an AC outlet 4.

3

The CHARGE lamp on the camcorder blinks to
indicate charging has started.

Battery pack

Power Switch

4

To AC outlet

Battery pack

BN-V11U*

BN-V12U (optional)

BN-V20U** (optional)

BN-V400U (optional)

* GR-AX761 only.
** Provided with GR-AXM231 only.

AC Adapter

approx. 1 hr. 30 min.

approx. 1 hr. 30 min.

approx. 2 hrs. 20 min.

approx. 4 hrs. 30 min.

To DC IN

3

connector

Charging time

When the CHARGE lamp stops blinking but stays lit,

4

charging is finished. Unplug the AC Adapter from the
AC outlet. Disconnect the AC Adapter from the
camcorder.

To Detach The Battery Pack . . .

.... slide BATTERY RELEASE and pull out the battery pack.

NOTES:

●

During charging or discharging, the camcorder cannot
be operated.

●

Charging and discharging is not possible if the wrong
type of battery is used.

●

When charging the battery pack for the first time or after
a long storage period, the CHARGE lamp may not light.
In this case, remove the battery pack from the
camcorder, then try charging again.

●

If the battery operation time remains extremely short
even after having been fully charged, the battery is worn
out and needs to be replaced. Please purchase a new
one.

●

Using the optional AA-V15 AC Power Adapter/Charger,
you can charge the BN-V11U/V12U/V20U/V400U
battery pack without the camcorder. However, it cannot
be used as an AC adapter.

REFRESH:

Charging a battery with some charge remaining reduces that battery’s capacity. Perform the procedure
below to fully discharge the battery pack before recharging.

1. Perform steps 1 through 3 of “CHARGING THE BATTERY PACK”.

2. Press REFRESH on the camcorder for over 2 seconds. The REFRESH lamp on the camcorder blinks to

indicate discharging has started.

3. When discharging is finished, charging automatically starts and the CHARGE lamp blinks.
When you are not using a battery pack for a long period of time, be sure to fully discharge it before storing

because leaving a battery with some charge left over also reduces performance.

For other notes, 墌 pg. 42

ATTENTION:

Before detaching the power source, make
sure that the camcorder’s power is turned
off. Failure to do so can result in a
camcorder malfunction.

Charge marker

A charge marker is provided on
the battery pack to help you
remember whether it has been
charged or not. Two colors are
provided (red and black)—you
choose which one means
charged and which means
discharged.

USING THE BATTERY PACK

Perform step 1 of “CHARGING THE BATTERY PACK”
(墌 pg. 6).

Approximate recording time (unit: min.)

Battery pack

BN-V11U

BN-V12U
(optional)

BN-V20U
(optional)

BN-V400U
(optional)

1 When using GR-AXM231
2 When using GR-AX761

( ) : when the video light is on (GR-AX761 only)

NOTES:

●

Recording time is reduced significantly under the
following conditions:

•

Zoom or Record-Standby mode is engaged repeatedly.

•

The LCD monitor is used repeatedly (GR-AXM231
only).

●

Before extended use, it is recommended that you
prepare enough battery packs to cover 3 times the
planned shooting time.

Viewfinder on

12

95 100

95 100

150 165

360 385

(50)

(50)

(90)

(210)

LCD monitor on

1

80

80

135

315

EN7

To AC outlet

AC Adapter

To DC IN
connector

USING AC POWER

Use the AC Adapter (connect as shown in the illustration).

NOTES:

●

The provided AC Adapter features automatic voltage
selection in the AC range from 110 V to 240 V.

●

For other notes, 墌 pg. 42.

8 EN

PAUSE

Power Zoom
Lever

Recording
Start/Stop
Button

GETTING STARTED

Grip Adjustment

Separate the Velcro strip.

1

Pass your right hand through the loop and grasp the

2

grip.

Adjust so that your thumb and fingers can easily

3

operate the Recording Start/Stop Button and Power
Zoom Lever. Refasten the Velcro strip.

Viewfinder Adjustment

(cont.)

33

22

180°180

Set the Power Switch to “ ” or “ ”.

1

Adjust the viewfinder manually for best viewability.

°

1

M

A

F

F

O

Y

A

L

P

Set to “
“ ”.

” or

2

Turn the Diopter Adjustment Control until the

3

indications in the viewfinder are clearly focused.

Shoulder Strap Attachment

EN9

4

2

3

1

Following the illustration, thread the strap through the

1

eyelet 1, then fold it back and thread it through the
buckle 2. Repeat the procedure to attach the other
end of the strap to the other eyelet 3, making sure
the strap is not twisted.

Adjust as shown in the illustration 4.

2

Tripod Mounting

Align the screw and camera direction stud on the

1

tripod with the camera’s mounting socket and stud
hole. Then tighten the screw.

CAUTION:

When using a tripod, be sure to open and extend
its legs fully to Stabilize the camcorder. To
prevent damage to the unit caused by falling
over, do not use a small-sized tripod.

10 EN

䊳

F
E

M

T

O
X
.

O

C

P

W

U
O
.

S

S
S
B

C

Y

U

.

A

S

R

M

T

E

EERMAMMEE

N

A
A
A

N

U

U
U
U

U

T
T
T

O
O
O

䊳

R
D

N

E
.

ECXZT

M
O

S

O
O

Y
D

M

SETEM ME

S
5

N
P

0

U

x

S

䊳

T

O

C

A

E

R

C

T

I

N

I

T

.

T

E

T

L

E

M

I

T

T

L

E

A

D

T

E

/

T

D

E

M

O

M

䊳

R

E

T

U

R

Display

Y

S

M

E

M

E

I

M

A

C

L

A

I

M

O

D

N

T
R

E
R
N

E

E

MENU Wheel

Power Switch

N

E

U

A

MMEEN

F

O

F

O

F

O

O

N

E

GM.

F

O

U
F

F
F
GFLISH

Menu Screen

GETTING STARTED

(cont.)

Date/Time Settings

Set the Power Switch to “ ”. The power lamp

1

comes on.

Press the MENU Wheel in. The Menu Screen

2

appears.

Rotate the MENU Wheel to select “ TO SYSTEM

3

MENU” and press it to display SYSTEM MENU.
Rotate the MENU Wheel to select “ NEXT” and
press it to display the next page.

Rotate the MENU Wheel to select “DATE/TIME” and

4

press it. The DATE/TIME Menu appears.

To set “YEAR”, “MONTH”, “DAY” or “TIME” (hour/

5

minute), rotate the MENU Wheel to select the desired
item, and press it. When the setting begins blinking,
rotate the MENU Wheel until the correct setting
appears and then press it. The setting stops blinking.

When none of these settings (“YEAR”, “MONTH”,

6

“DAY”, “TIME”) blinks, rotate the MENU Wheel to
select “EXIT”, and press it. The Menu Screen
reappears with the highlight bar on “ RETURN”.

Press the MENU Wheel in to close the Menu Screen.

7

NOTE:

To display the date and time in the camcorder’s display and
on a connected TV, see “Date/Time Insert” (墌 pg. 25).

DATE/ T IPMME

Y

E

A

R

M

O

N

T

H

D

A

Y

T

I

M

E

E

X

I

T

280

J

:

1

0

U

N

2

8

2

0

DATE/TIME Menu

12-hour
indication with
AM or PM

For other notes, 墌 pg. 42

S

SP

E

E

P

P

XIT

Display

REC MODE

MENU Wheel

Power Switch

REC MODE Menu

Recording mode
indicator

EN11

Recording Mode Setting

Set the tape recording mode depending on your preference.

Set the Power Switch to “ ”. The power lamp

1

comes on.

Press the MENU Wheel in. The Menu Screen

2

appears.

Rotate the MENU Wheel to select “ TO SYSTEM

3

MENU” and press it to display SYSTEM MENU.

Rotate the MENU Wheel to select “REC MODE” and

4

press it. The REC MODE Menu appears. Select “SP”
or “EP” by rotating the MENU Wheel and press it.
The Menu Screen reappears with the highlight bar on
“ RETURN”. Press the MENU Wheel in to close the
Menu Screen.

•“EP” (Extended Play) is more economical, providing
three times the recording time.

NOTE:

If the recording mode is switched during recording, the
playback picture will be blurred at the switching point.

12 EN

T

30

T

2

0

T

3

0

T

3

5

T

4

0

X

IT

E

MENU Wheel

Power Switch

Display

TAPE LENGTH

TAPE LENGTH
Menu

GETTING STARTED

(cont.)

Tape Length Setting

Set the tape length according to the length of the tape
used.

Set the Power Switch to “ ”. The power lamp

1

comes on.

Press the MENU Wheel in. The Menu Screen

2

appears.

Rotate the MENU Wheel to select “ TO SYSTEM

3

MENU” and press it to display SYSTEM MENU.

Rotate the MENU Wheel to select “TAPE LENGTH”,

4

then press it. The TAPE LENGTH Menu appears.

Rotate the MENU Wheel to select the correct tape

5

length setting.

•T20=20 minutes

•T30=30 minutes

•T35=35 minutes

•T40=40 minutes

(in SP)

Tape length
indicator

Press the MENU Wheel in. The Menu Screen

6

reappears with the highlight bar on “ RETURN”.
Press the MENU Wheel in to close the Menu Screen.

NOTE:

The tape remaining time (墌 pg. 14) is correct only if the
correct tape length has been selected.

Cassette holder

Close Button

EJECT Switch

Loading/Unloading A Cassette

Open the LCD monitor fully (GR-AXM231 only).

1

Slide EJECT until the cassette holder opens. Do not

2

use force to open.

Insert or remove a cassette. When inserting, make

3

sure the label is facing outward.

Press the Close button to close the cassette holder

4

until it locks into place.

Close the LCD monitor (GR-AXM231 only).

5

EN13

EJECT Switch

Cassette holder

Close Button

Erase Protection tab Gear

Turn to take
up slack.

NOTES:

●

Closing the LCD monitor while the cassette holder is still
open may cause damage to the LCD monitor
(GR-AXM231 only).

●

The cassette holder can’t be opened unless a power
supply is attached.

●

Make sure that the tape is not slack when loading the
cassette. If there is any slack, turn the gear on the
cassette in the direction of the arrow to take up the
slack.

●

Make sure the Erase Protection tab is in the position that
allows recording. If not, slide the tab. Some cassettes
have removable tabs. If the tab has been removed, cover
the hole with adhesive tape.

●

The cassette holder cannot be opened while the
camcorder is in the record mode.

14 EN

BR I GHT

–

–––––––6–––

+

25

MIN

RECORDING

NOTE:

You should already have performed the procedures listed
below. If not, do so before continuing.

●

Power (墌 pg. 6)

●

Load A Cassette (墌 pg. 13)

●

Recording Mode Setting (墌 pg. 11)

●

Tape Length Setting (墌 pg. 12)

●

Grip Adjustment (墌 pg. 8)

●

Viewfinder Adjustment (墌 pg. 8)

Basic Recording

During shooting

Power Switch

Recording Start/Stop Button

Tape remaining
time indicator
(Approximate)

90°

120MIN

1MIN0MIN

BRIGHT Wheel
(GR-AXM231 only)

2MIN

3MIN

MIN 119MIN

(Now calculating)

(Blinking) (Blinking) (Blinking)

180°

To Adjust The Brightness Of The LCD Monitor

.... rotate the BRIGHT Wheel until the bright

level indicator on the display moves and
the appropriate brightness is reached.

Shooting While Watching The Viewfinder

Make sure the LCD monitor is closed and locked

1

(GR-AXM231 only). Press in the tabs on the lens cap
to remove it. Set the Power Switch to “ ” or “ ”.
The power lamp lights and the camcorder enters the
Record-Standby mode. “PAUSE” is displayed in the
viewfinder.

Press the Recording Start/Stop Button. “ ” appears

2

in the viewfinder while recording is in progress.

To Stop Recording . . .

.... press the Recording Start/Stop Button. The camcorder

re-enters the Record-Standby mode.

Shooting While Watching The
LCD Monitor (GR-AXM231 only)

Make sure the LCD monitor is fully open. Press in the

1

tabs on the lens cap to remove it. Set the Power
Switch to “ ” or “ ”. The power lamp lights and
the camcorder enters the Record-Standby mode.
“PAUSE” is displayed in the LCD monitor.

Tilt the LCD monitor upward/downward for best

2

viewability and press the Recording Start/Stop Button.
“ ” appears in the LCD monitor while recording is
in progress.

NOTE:

When you use the LCD monitor outdoors in direct
sunlight, the LCD monitor may be difficult to see. If this
happens, use the viewfinder instead.

To Stop Recording . . .

.... press the Recording Start/Stop Button. The camcorder

re-enters the Record-Standby mode.

: Suitable for standard recording using NO special effects or manual adjustments.
: Allows you to set recording functions using the menus for more creative capabilities.

OFF : Switches off the camcorder.

: Allows you to play back your recordings.

Power Switch Position

EN15

NOTES:

●

If the Record-Standby mode continues for 5 minutes without performing Zoom or any other operations, the
camcorder’s power shuts off automatically. Set the Power Switch to “OFF”, and then back to “ ” or “ ” to
turn the camcorder on again.

●

If you are recording on a cassette from the middle (such as when a tape is removed and re-inserted during
recording), use the Retake function (墌 pg. 17) to find the end of the last recording so you do not erase any
of it.

●

To remove the indications from the camcorder’s display during recording, 墌 pg. 22, 24.

Self-Recording

JOURNALISTIC SHOOTING

(GR-AXM231 only)

In some situations, different shooting angles may
provide more dramatic results. Hold the camcorder in
the desired position and tilt the LCD monitor in the
most convenient direction. It can rotate 270° (90°
downward, 180° upward).

SELF-RECORDING (GR-AXM231 only)

You can shoot yourself while viewing your own
image in the LCD monitor. Open the LCD monitor
and tilt it upward 180° so that it faces forward, then
point the lens toward yourself and start recording.

For other notes, 墌 pg. 42

16 EN

Zoom in (T: Telephoto)

Display

Zoom out (W: Wide angle)

Power Zoom Lever

Zoom indicator
bar

1

x

Zoom level
indicator

Approximate
zoom ratio

RECORDING

Basic Features

Zooming: To produce the zoom in/out effect, or an

instantaneous change in image magnification.
Digital circuitry extends the maximum magnification offered
by optical zoom. This system is called Digital Zoom.

Zoom In
Slide the Power Zoom Lever towards “T”.

Zoom Out
Slide the Power Zoom Lever towards “W”.

●

The further you slide the Power Zoom Lever, the quicker
the zoom action.

●

Focusing may become unstable during Zooming. In
this case, set the zoom while in Record–Standby, lock
the focus by using the manual focus (墌 pg. 28), then
zoom in or out in Record mode.

●

The zoom level indicator
Once the zoom level indicator reaches the top of the
zoom indicator bar, all magnification from that point is
through digital processing.

●

When using Digital Zoom, the quality of image may
suffer. To deactivate Digital Zoom, set “D.ZOOM” to
“OFF” in SYSTEM MENU (墌 pg. 23).

(5)

moves during zoom.

Display

P. STABILIZER
Button

Picture Stabilizer
indicator

Picture Stabilizer:

images caused by camera-shake, particularly at high
magnification.

1) Press P. STABILIZER. “ ” appears.

2) To switch off the Picture Stabilizer, press
P. STABILIZER. The indicator disappears.

●

Accurate stabilization may not be possible if hand shake
is excessive, or under the following conditions:

•

When shooting subjects with vertical or horizontal
stripes.

•

When shooting dark or dim subjects.

•

When shooting subjects with excessive backlighting.

•

When shooting scenes with movement in various
directions.

•

When shooting scenes with low-contrast backgrounds.

●

Switch off the Picture Stabilizer when recording with
the camcorder on a tripod.

●

The “ ” indicator appears blinking if the Stabilizer
cannot be used.

To compensate for unstable

Quick Review (2) Button

EN17

Quick Review:

recording.

1) Make sure the camcorder is in the Record–Standby
mode.

2) Press 2 and release quickly.
Tape is rewound for approx. 2 seconds and played
back automatically, then pauses in Record–Standby
mode for the next shot.

●

Distortion may occur at the start of playback. This is
normal.

To check the end of the last

Set to “

RETAKE (2/3) Button

Set to “

5 SEC. REC
Button

Set to “ ” or “ ”.

” or “ ”.

” or “ ”.

Retake:

1) Make sure the camcorder is in the Record–Standby
mode.

2) Press and hold either RETAKE to reach the start point for
new recording. Pressing 3 forwards the tape and
pressing 2 reverses it.

3) Press the Recording Start/Stop Button to start recording.

●

Noise bars appear and pictures may become mono-

To re-record certain segments.

chrome or darken during Retake. This is normal.

5Sec. Rec (5-Sec. Recording):

To record a scene for 5 seconds, providing quick scene
transitions like those seen in TV programs.

1) Make sure the recording mode is set to “SP”.

2) During Record–Standby, press 5 SEC. REC. “ 5S”

appears and 5Sec. Rec is reserved.

3) Press the Recording Start/Stop Button. Recording starts,
and after 5-second recording is finished, the camcorder
reenters the Record–Standby mode automatically.

4) To cancel the 5Sec. Rec. function, press 5 SEC. REC
again so that “ 5S” disappears.

●

Fade/Wipe (墌 pg. 19) cannot be activated by pressing
5 SEC. REC.