JVC GR-AX710, GR-AX510 User Manual

COMP ACT VHS CAMCORDER
GR-AX710 GR-AX510
(The camcorder illustrations appearing in these instructions are of the GR-AX710.)
INSTRUCTIONS
Compact VHS
For Customer Use:
Enter below the Serial Nos. of the GR-AX710U/GR-AX510U camcorder and the AA-V11U AC Power Adapter/ Charger. The serial numbers are located on the bottom of the GR-AX710U/GR-AX510U, and the AA-V11U.
AA-V11U
Serial No.
YU30052-508-1
2
Dear Customer,
Thank you for purchasing the JVC Compact VHS camcorder. Before use, please read the safety information and precautions contained in the following pages to ensure safe use of your new camcorder.
Using This Instruction Manual
• All major sections and subsections are listed in the Table Of Contents (
• Notes appear after most subsections. Be sure to read these as well.
• Basic and advanced features/operation are separated for easier reference.
It is recommended that you . . .
..... refer to the Index (
familiarize yourself with button locations, etc. before use.
..... read thoroughly the Safety Precautions and Safety
Instructions that follow. They contain extremely important information regarding the safe use of your new camcorder.
You are recommended to carefully read the cautions on pages 43 and 44 before use.
Z pg. 7).
Z pgs. 40 – 42) and
SAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. 
NO USER-SERVICEABLE PARTS INSIDE.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. 
 The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
The AA-V11U AC Power Adapter/Charger should be used with: AC 120 V`, 60 Hz in the USA and Canada, AC 110 – 240 V`, 50/60 Hz in other countries.
CAUTION (applies to the AA-V11U)
TO PREVENT ELECTRIC SHOCK MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION (s'applique à l'AA-V11U)
POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
Warning on lithium battery
The battery used in this device may present a fire or chemical burn hazard if mistreated. Do not recharge, disassemble, heat above 100°C (212°F) or incinerate. Replace the battery with Panasonic (Matsushita Electric), Sanyo or Maxell CR2025; use of another battery may present a risk of fire or explosion.
n Dispose of used battery promptly. n Keep away from children. n Do not disassemble and do not dispose of in fire.
NOTES:
The rating plate (serial number plate) and safety caution are on the bottom and/or the back of the main unit.
The rating plate (serial number plate) of the AC Power Adapter/Charger is on its bottom.
This Class B digital apparatus meets all requirements of the Canadian Interference – Causing Equipment Regulations.
“Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.“
This camcorder is designed to be used with NTSC-type color television signals. It cannot be used for playback with a television of a different standard. However, live recording and viewfinder playback are possible anywhere. Use the BN-V11U/V12U/V22U/V25U battery packs and, to recharge them, the provided multi-voltage AC Power Adapter/Charger. (An appropriate conversion adapter may be necessary to accommodate different designs of AC outlets in different countries.)
ATTENTION:
The product that you have purchased is powered by a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal.
IMPORTANT PRODUCT SAFETY INSTRUCTIONS
Electrical energy can perform many useful functions. But improper use can result in potential electrical shock or fire hazards. This product has been engineered and manufactured to assure your personal safety. In order not to defeat the built-in safeguards, observe the following basic rules for its installation, use and servicing.
ATTENTION:
Follow and obey all warnings and instructions marked on your product and its operating instructions. For your safety, please read all the safety and operating instructions before you operate this product and keep this manual for future
reference.
INSTALLATION
1. Grounding or Polarization
(A) Your product may be equipped with a polarized
alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
(B) Your product may be equipped with a 3-wire
grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.
2. Power Sources
Operate your product only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. If your product is intended to operate from battery power, or other sources, refer to the operating instructions.
3. Overloading
Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.
4. Power Cord Protection
Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.
5. Ventilation
Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered.
• Do not block the openings by placing the product on a bed, sofa, rug or other similar surface.
• Do not place the product in a built-in installation such as a bookcase or rack unless proper ventilation is provided
or the manufacturer’s instructions have been adhered to.
6. Wall or Ceiling Mounting
The product should be mounted to a wall or ceiling only as recommended by the manufacturer.
ANTENNA INSTALLATION INSTRUCTIONS
1. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
2. Lightning
For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line
surges.
3. Power Lines
An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
ANTENNA LEAD IN WIRE
GROUND CLAMP
ANTENNA DISCHARGE UNIT (NEC SECTION 
ELECTRIC SERVICE EQUIPMENT
POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250. PART H)
NEC – NATIONAL ELECTRICAL CODE
810-20)
GROUNDING  CONDUCTORS (NEC SECTION 810-21)
GROUND CLAMPS
3
4
USE
1. Accessories
To avoid personal injury:
• Do not place this product on an unstable cart, stand, tripod, bracket or table. It may fall, causing serious injury to a child or adult, and serious damage to the product.
• Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with the product.
• Use a mounting accessory recommended by the manufacturer and follow the manufacturer’s instructions for any mounting of the product.
• Do not try to roll a cart with small casters across thresholds or deep-pile carpets.
2. Product and Cart Combination
A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.
3. Water and Moisture
Do not use this product near water—for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool and the like.
4. Object and Liquid Entry
Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
5. Attachments
Do not use attachments not recommended by the manufacturer of this product as they may cause hazards.
6. Cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
7. Heat
The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
PORTABLE CART WARNING (Symbol provided by RETAC)
SERVICING
1. Servicing
If your product is not operating correctly or exhibits a marked change in performance and you are unable to restore normal operation by following the detailed procedure in its operating instructions, do not attempt to service it yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
2. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:
a. When the power supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the
product.
c. If the product has been exposed to rain or water. d. If the product does not operate normally by following
the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation.
e. If the product has been dropped or damaged in any way. f. When the product exhibits a distinct change in
performance—this indicates a need for service.
3. Replacement Parts
When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.
4. Safety Check
Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in safe operating condition.
QUICK OPERATION GUIDE
5
SUPPLY POWER
Hook on.
1
Push in.
2
BATT. RELEASE
Using the battery pack
1
Hook-on the battery pack's top end to the camcorder. (Charging procedure, Z P. 8)
2 Push in the battery pack until it locks into
place.
To remove the battery pack
Slide BATT. RELEASE and pull out the battery pack.
PLAYBACK
PLAY/PAUSE
3
REW
2
STOP
INSERTING A VIDEO CASSETTE
EJECT
1
3
PUSH
1 Slide EJECT. 2 Insert a video cassette. 3 Press PUSH.
(For more details, Z P. 11)
SHOOTING
2
Insert.
LENS COVER open/close knob
2
Set to “CAMERA”
Recording Start/Stop button
3
1
1
Set to “PLAY”
1 Set the power switch to “PLAY”. 2 Press REW.
— The tape will automatically stop at the
beginning of the tape.
3 Press PLAY/PAUSE.
— Playback starts and the playback picture
appears in the viewfinder.
•To stop playback, press STOP.
(For more details, Z P. 30.)
Or simply play back the tape on a VHS
n
VCR using the Cassette Adapter (VHS Playpak). Z P. 28
1 Slide the LENS COVER open/close knob to
open the lens cover.
2 Set the power switch to “CAMERA”.
— The power indicator will light and an
image will appear in the viewfinder.
3 Press the Recording Start/Stop button.
— Recording starts.
•To stop recording temporarily, momentarily press the Recording Start/Stop button once again. (For more details, Z P. 14)
6
SEL
F1
F2
MAJOR FEATURES
REMEMBER
The Logical Choice
The only compact video
cassettes that can be
used with your VHS VCR*
Program AE with Special Effects (
n Auto Mode Lock n Auto Mode Release n Electronic Fog Filter n ND Effect n Sepia n Twilight n Sports n High Speed (1/2000 sec.) Shutter n 15 sec. Self Timer
Z P. 16)
Intelligent Function Control
Z P. 18 – 25)
(
Variable-Speed Hyper Zoom
Z P. 15)
(
Zoom-in
T
W
T
W
T
W
Zoom-out
T
W
Random Assemble Editing
Z P. 32 – 35)
(
882
554411663
7
Integrated Auto Light (GR-AX710 only) (
Z P. 18)
PROVIDED ACCESSORIES
•AC Power Adapter/Charger AA-V11U
•Battery Pack BN-V11U
•Cassette Adapter
3
2
(VHS PlayPak) C-P7U
Cassettes marked can be used with this camcorder.
•Remote Control Unit RM-V705U (GR-AX710 only)
7
•Shoulder Strap
•Lithium Battery
x2 for GR-AX710 (clock operation and
remote control unit) x1 for GR-AX510 (clock operation)
CONTENTS
GETTING STARTED
Power..................................................................................... 8
Clock (Lithium) Battery Removal/Insertion........................................ 10
Date/Time Settings ................................................................... 10
Viewfinder Adjustment ............................................................... 11
Tape Length/Recording Mode Setting .............................................. 11
Loading/Unloading A Cassette ...................................................... 11
Grip Adjustment ....................................................................... 12
Shoulder Strap Attachment........................................................... 12
Tripod Mounting ....................................................................... 12
Remote Control Unit .................................................................. 13
RECORDING
Basic Recording ........................................................................ 14
Basic Features ......................................................................... 15
Advanced Features .................................................................... 16
PLAYBACK
Using The Cassette Adapter.......................................................... 28
Basic Connections...................................................................... 29
Basic Playback ......................................................................... 30
Features ................................................................................ 31
EDITING
Tape Dubbing........................................................................... 32
Random Assemble Editing (R.A.Edit)................................................ 32
Insert Editing........................................................................... 36
Audio Dubbing ......................................................................... 37
USER MAINTENANCE TROUBLESHOOTING INDEX
Controls................................................................................. 40
Connectors.............................................................................. 40
Indicators ............................................................................... 40
Other Parts............................................................................. 40
Viewfinder ............................................................................. 41
Terms .................................................................................... 42
CAUTIONS SPECIFICATIONS OPTIONAL ACCESSORIES ESPAÑOL FOR SERVICING WARRANTY
7
8
GETTING STARTED
14
RECORDING
28
PLAYBACKEDITING
32
38 39 40
43 45 45 46 48 49
8
END indicator
CHG. (charge) indicator
Marks
POWER indicator
REFRESH indicatorREFRESH switch
To AC outlet
GETTING STARTED
Power
This camcorder’s 3-way power supply system lets you choose the most appropriate source of power.
NOTES:
No function is available without power supply.
Use only specified power supply.
Do not use provided power supply units with other equipment.
CHARGING THE BATTERY PACK
SUPPLY POWER
Connect the charger’s AC power cord to a wall
1
outlet. The power indicator lights.
ATTACH BATTERY PACK
Align the marks and slide the battery pack in the
2
direction of the arrow until it locks in place. The CHG. indicator lights.
DETACH BATTERY PACK
When charging is completed, the END indicator
3
lights. Slide the battery pack opposite the direction of the arrow.
BATT. PACK CHARGE DISCHARGE
BN-V11U approx. 1 hr. 10 min.
BN-V12U approx. 1 hr. 10 min.
BN-V22U approx. 2 hrs. 10 min. approx. 7 hrs. BN-V25U approx. 2 hrs. 40 min. approx. 10 hrs.
approx. 3 hrs. 30 min.
approx. 3 hrs. 30 min.
Hook on.
Push in.
BATT. RELEASE
USING THE BATTERY PACK
ATTACH BATTERY PACK
Hook its top end to the camcorder and push the
1
battery pack in until it locks in place.
DETACH BATTERY PACK
Slide BATT. RELEASE and pull out the battery pack.
2
RECORDING TIME
BATT. PACK GR-AX710/AX510
BN-V11U approx. 1 hr. (40 min.) BN-V12U approx. 1 hr. (40 min.) BN-V22U approx. 2 hrs. 10 min. (1hr. 20 min.) BN-V25U approx. 2 hrs. 50 min. (1hr. 50 min.)
( ): when the video light is on (GR-AX710 only).
**REFRESH
The AC power adapter features a REFRESH function that allows you to fully discharge the battery pack before recharging.
To discharge the battery . . .
..... attach the battery pack to the adapter as shown in the
illustration to the left. Then push REFRESH. The REFRESH indicator lights when discharging starts, and goes out when discharging is complete.
**CHARGE MARKER
Charge marker
A charge marker is provided on the battery pack to help you remember whether it has been charged or not. Two colors are provided (red and black)—you choose which one means charged and which means discharged.
NOTES:
The recording time per charge is affected by such factors as the time spent in Record/Standby mode and the frequency of zooming. It is safer to have spare battery packs.
Charging times noted on page 8 are for fully discharged battey pack, and discharging times are for fully charged battery pack.
Charging and discharging times vary according to the ambient temperature and the status of the battery pack.
Remember to set the charge marker after charging a battery pack or after detaching a discharged one from your camcorder.
Perform the REFRESH function after no less than 5 chargings.
High temperatures can damage the battery pack, so use only where good ventilation is available. Don’t allow it to discharge in container, such as a bag.
If you stop recharging or discharging part way through, make sure to remove the battery pack before unplugging the adapter’s AC cord.
Remove the battery pack from the adapter immediately after discharging.
To avoid interference with reception, do not use the AC Power Adapter/Charger near a radio.
Make sure you unplug the DC cord before charging or discharging the battery pack.
A blinking CHG. indicator means that the battery pack has become hot. Wait until it cools down to continue.
The CHG. indicator may not light properly with a brand new battery pack, or with one that’s been stored for an extended period. In this case, remove and reattach the battery pack and recharge it. The CHG. indicator should light during recharging. If not, contact your nearest JVC dealer.
9
To AC outlet
DC OUT terminal
AC Power
DC cord
Car Battery Cord AP-V7U (optional)
Car Battery Charger/Adapter BH-V3U (optional)
Adapter/Charger AA-V11U
To car's cigarette lighter socket
USING A CAR BATTERY
Use the optional Car Battery Cord or Car Battery Charger/Adapter (connect as shown in the illustration to the left).
NOTES:
When using the car battery, leave the engine idling.
The optional Car Battery Charger (BH-V3U) can also be used to charge the battery pack.
When using the optional Car Battery Charger or Car Battery Cord (AP-V7U), refer to the respective instruction booklet.
USING AC POWER
Use the AC Power Adapter (connect as shown in the illustration to the left).
NOTE:
The supplied AC Power Adapter/Charger features automatic voltage selection in the AC range from 110 V to 240 V.
10
A
–/+ SET
GETTING STARTED (cont.)
Clock (Lithium) Battery Removal/Insertion
This battery is necessary for clock operation and to perform date/time settings.
SWITCH OFF POWER
Switch off the unit’s power and remove the power
1
supply unit.
OPEN COVER
Open the clock battery compartment cover while
2
pressing the release tab.
REMOVE BATTERY (when replacing)
Insert a pointed, non-metallic object between the
3
battery and the compartment ( battery out.
INSERT BATTERY
Ensuring the plus (+) side is up, insert the supplied
4
lithium battery and push it in.
CLOSE COVER
Close the compartment cover until it clicks in place.
A
) and pull the
5
NOTE:
See “SAFETY PRECAUTIONS”(Z pg. 2) for information on safe handling of lithium batteries.
Date
Month/Day/Year DATE ... Date setting is performed
DATE JAN 1.00
TIME AM12:00
Time
12-hour indication with AM or PM
TIME .... Time setting is performed
POWER
Date/Time Settings
SELECT MODE
Set the power switch to CAMERA.
1
SET DATE/TIME
Press SET and the month blinks. Press + or to set
2
the month. Repeat to set day, year, hour and minute.
START CLOCK
Press SET. The blinking stops. The date and time are
3
both displayed for confirmation, then the time display disappears.
NOTE:
The clock does not keep time while the date and time are blinking.
SP-EP recording mode and T20•30•40 tape length select button
Viewfinder Adjustment
POSITION VIEWFINDER
Adjust the viewfinder manually for best viewability
1
(see illustration at left).
SELECT MODE
Set the power switch to CAMERA.
2
ADJUST DIOPTER
Turn the diopter adjustment control until the
3
indications in the viewfinder are clearly focused.
Tape Length/Recording Mode Setting
SET TAPE LENGTH
Set the tape length button according to the length of
1
the tape used. T20 = 20 minutes of recording time, T30 = 30 minutes, and T40 = 40 minutes (in SP).
11
Set POWER to "CAMERA".
Tape length and recording mode indicator
T30 SP
T20 SP T40 EP T40 SP T30 EP
Turn to take up slack.
GearErase Protection
T20 EP T30 SP
SET RECORDING MODE
Set depending on your preference. “SP” (Standard
2
Play) provides higher picture and sound quality and is better for dubbing, while “EP” (Extended Play) is more economical, recording at 1/3 the speed of SP.
Loading/Unloading A Cassette
OPEN CASSETTE HOLDER
Slide EJECT until the holder opens. Do not use force
1
to open.
INSERT/REMOVE CASSETTE
Make sure the label is facing outward.
2
CLOSE CASSETTE HOLDER
Press PUSH and make sure the holder is closed and
3
locked.
NOTES:
A cassette holder can’t be opened unless a power supply is attached.
Make sure that the tape is not slack when loading the cassette. If there is any slack, turn the gear on the cassette in the direction of the arrow to take up the slack.
Make sure the Erase Protection tab is present. If not, cover the hole with adhesive tape. (Some cassettes have sliding tabs – in this case, check the tab's position.)
12
3
Recording Start/Stop button
1
2
1
2
GETTING STARTED (cont.)
Grip Adjustment
EXPAND LOOP
Separate the Velcro strip.
1
INSERT HAND
Pass your right hand through the loop and grasp the
2
grip.
ADJUST STRAP LENGTH
Adjust so your thumb and fingers can easily operate
3
the Recording Start/Stop button and Power Zoom switch. Refasten the Velcro strip.
Shoulder Strap Attachment
ATTACH STRAP
Following the illustration at left, thread the strap
1
through the top of the eyelet (1), then fold it back and thread it through the keeper (2), and then through the buckle (3). Repeat the procedure to attach the other end of the strap to the other eyelet, making sure the strap isn’t twisted.
ADJUST LENGTH
Adjust as shown in the illustration at left (1), then
2
slide both keepers snug against the eyelets to prevent slipping (2).
Tripod Mounting
ALIGN AND TIGHTEN
Align the screw and camera direction stud on the
1
tripod with the camera’s mounting socket and stud hole. Then tighten the screw.
Infrared beam effective area
10°
5m(16.4ft)
30°
30°
10°
The transmitted beam may not be effective or may cause incorrect operation when the infrared beam sensor window is directly exposed to sunlight or powerful lighting.
Infrared beam sensor window
13
Remote Control Unit (provided with GR-AX710 only)
The Full-Function Remote Control Unit can operate this camcorder from a distance as well as the basic operations (PLAY, STOP, PAUSE, FF, and REW) of your VCR. This remote control unit makes additional recording functions possible.
PULL OUT BATTERY HOLDER
Pull out the battery holder by inserting a pointed
1
instrument into slot A.
INSERT BATTERY
Insert the lithium battery *(CR2025), with its plus (+)
2
side up, into the battery holder.
2
1
7
REPLACE BATTERY HOLDER
Insert the battery holder into the remote control unit,
3
and push the holder until it clicks in place. *Read warning on lithium battery. (Z P. 2)
8
3
4
5
6
Buttons
1 Infrared beam Transmits the beam signal.
transmitting window
2 ZOOM (T/W) buttons Zoom (invariable speed, Z pg. 15) 3 PLAY button Playback start (Z pg. 30) 4 STOP button Stop (Z pg. 30) 5 REW button Retake (Rewind) (Z pg. 15) Rew/Rew Shuttle Search (Z pg. 30) 6 INSERT button Insert Editing (Z pg. 36) 7 START/STOP button Functions same as the Recording Start/Stop button of the camcorder. 8 INT. TIME button Self-Timer(Z pg. 26)/Time Lapse (Z pg. 27) 9 REC TIME button Animation/Time lapse (Z pg. 27) 0 PAUSE button Pause (Z pg. 31) ! FF button Retake (Forward) (Z pg. 15) FF/FF Shuttle Search (Z pg. 30) @ A. DUB button Audio dubbing (Z pg. 37)
With the camcorder’s power switch With the camcorder’s power switch set set to “CAMERA”. to “PLAY”.
9
0
!
@
A
2
Functions
3
1
14
LENS COVER SWITCH
RECORDING
Basic Recording
NOTE:
You should already have performed the procedures listed below. If not, do so before continuing.
Power (Z pg. 8)
Tape Length/Recording Mode Setting (Z pg. 11)
Grip Adjustment (Z pg. 12)
LOAD A CASSETTE
Slide EJECT to open the cassette holder, then insert
1
the cassette with the label facing out. Press PUSH to ensure the holder is closed and locked.
POWER
Start/Stop
The power indicator
Tape remaining time indicator
120MIN 119MIN
1MIN (Blinking)
0MIN (Blinking)
* MIN.....(Now calculating)
Tally lamp
2MIN (Blinking)
3MIN
ENTER RECORD–STANDBY MODE
Slide the LENS COVER open/close switch to open
2
the lens cover, then set the power switch to CAMERA.
•The power indicator lights and the camcorder enters the Record–Standby Mode.
•The scene you’re aimed at appears on the viewfinder screen, with the word “PAUSE” superimposed upon it.
START SHOOTING
Press the Recording Start/Stop button.
3
•The tally lamp lights while recording is in progress,
REC
and “
STOP RECORDING
Press the Recording Start/Stop button again to stop
4
recording.
•The camcorder re-enters the Record-Standby mode.
NOTES:
A cassette holder can’t be opened unless a power supply is attached.
There may be a delay after you slide EJECT until the holder opens. Do not use force.
The tape’s remaining time is displayed in the viewfinder as shown.
“TAPE END” appears when the tape reaches its end, and the power goes off automatically if left in this condition for 5 minutes. “TAPE END” also appears when a cassette whose tape is already at its end is loaded.
If the Record–Standby mode continues for 5 minutes, the camcorder’s power shuts off automatically. Set the power switch to POWER OFF, and then back to CAMERA to turn the camcorder on again.
If you’re recording on a cassette from the middle, use the RETAKE function (Z pg. 15) to find the end of the last recording so you don’t erase any of it.
The LENS COVER warning blinks for about 5 seconds when the camcorder is turned on, whether the cover is open or closed.
” appears in the viewfinder.
RECORDING
Basic Features
15
Zoom indicator
T
W
T
W
RETAKE
Power zoom switch
RM-V700U (optional)
Zoom-in
Zoom-out
START/STOP VISS
FEATURE: Zooming PURPOSE: Varies the focal length of the lens and
T
W
T
W
OPERATION:
NOTES:
produces the zoom in/out effect.
Zoom In
1) Pull the power zoom switch down
toward “T”.
Zoom Out
2) Push the switch up toward “W”.
The further the power zoom switch is pushed, the faster the zoom speed becomes.
Focusing may become unstable during zooming. In this case, set the zoom while in Record–Standby, set manual focus or Focus Lock ( 20, 21), then zoom in or out in Record mode.
FEATURE: Quick Review PURPOSE: To check the end of the last recording. OPERATION: 1) Press “
NOTE:
FEATURE: Retake PURPOSE: To re-record certain segments. OPERATION: 1) Make sure the camcorder is in the
NOTE:
FEATURE: Index Code Marking PURPOSE: To give you automatic access to any
OPERATION:
NOTES:
during the Record–Standby mode.
• Tape is rewound for about 2
Distortion may occur at start of playback. This is normal.
Record–Standby mode.
2) Press either RETAKE button to reach
the start point for new recording.
3) Press Recording Start/Stop to start
recording.
Noise may appear during Retake. This is normal.
selected point on a recording. Auto Marking and Manual Marking are available.
Auto Marking
An index code is always marked to start the first recording on a new date after a cassette is inserted.
Manual Marking (Using the optional RM-V700U Remote Control Unit)
1) Press VISS once to place the index
code. INDEX blinks in the viewfinder during marking.
If VISS is pressed during Record–Standby mode, the mark is
” for less than 2 seconds
seconds and played back automatically, then pauses in Record–Standby mode for thenext shot.
Z
pg.
placed where START/STOP is pressed.
If the date changes during a recording, it becomes the first recording of the new date and an index mark is placed at that point.
16
Program AE With Special Effects
All you have to do to access any of the variety of shooting effects is to turn the PROGRAM AE select dial until the desired indication appears in the viewfinder. The mode is activated about 1 second later.
RECORDING
Advanced Features
PROGRAM AE select dial
DIAL VIEWFINDER
SYMBOL INDICATION
LOCK
Auto Mode Lock
Locks the camcorder in Full Auto mode, preventing incorrect operation due to accidental button pressing during shooting.
•CINEMA, FADER, FOCUS, EXPOSURE, DISPLAY, TITLES and MWB (Manual White Balance) controls are disabled in this mode.
RELEASE
Auto Mode Release
Re-enables the controls that were disabled by Auto Mode Lock.
Electronic Fog Filter
Makes the picture look misty white, as when an external fog filter is attached to the lens. Softens the image and gives it a “fancy“ look.
ND EFFECT
A black mist darkens the picture, as when an ND filter is used. Helps to counter the effects of glare on the subject.
Sepia
The scene being shot is recorded in sepia-tinted (reddish-brown) monochrome, giving the effect of an older movie. Use together with Cinema (
Z pg. 19) for the authentic look of a classic
Hollywood movie.
Twilight
Disengages the auto gain control and auto focus, locks focus to infinity and white balance to “ ” (outdoor) mode. Dusk, twilight scenery, fireworks, etc., look more natural and dramatic.
AUTO LOCK
A
AUTO RELEASE
M
FG:FOGFG
SEPIA
TWILIGHT
MODE
Auto Mode Lock
Auto Mode  Release
Electronic Fog Filter
ND EffectND:ND EFFECTND
Sepia
Twilight
Tally lamp
DIAL VIEWFINDER
SYMBOL INDICATION
SPORTS
Sports
High shutter speed clearly captures fast-moving action.
1/2000
High-Speed Shutter (1/2000s.)
Captures faster action than Sports mode.
15sec. Self-Timer
Lets you delay recording start after Recording Start/ Stop is pressed. If camcorder is secured, operator can enter scene before recording starts.
1) Set PROGRAM AE dial to “
in viewfinder.
2) Press Recording Start/Stop.
•Recording starts after 15 seconds.
•Tally lamp begins blinking; blinking speed increases about 5 seconds before recording starts. Blinking stops when recording begins but light stays on.
S 1/2000
SELF TIMER
MODE
Sports
High Speed Shutter
15 sec. Self-Timer
”. “ 15S” appears
NOTES:
Only one effect can be engaged at a time.
When the PROGRAM AE select dial is switched from one mode to another, the newly selected mode's name and its indication is displayed in the viewfinder for approx. 3 seconds. Then the name disappears, and only the indication remains.
The screen becomes slightly reddish when the fader (Z pg. 19) is used in the Sepia mode.
The screen becomes slightly dark in the High Speed Shutter mode. Use in well-lighted situations.
In the High Speed Shutter or Sports modes, picture color may be adversely affected if subject is lit by alternating discharge-type light sources such as flourescent or mercury-vapor lights.
Loading...
+ 36 hidden pages