at NTSC 0.286 V (p-p)/75 Ω
PB/PR output: 0.7 V (p-p)/75 Ω
Ω
Ω at 1 kHz with no more than 10% total har-
monic distortion
Ω to 16 Ω
Ω
200 mV/50 kΩ
750 mV/50 kΩ
Ω Unbalanced type
531 kHz to 1 710 kHz (9 kHz step) (FS-XA3UF)
530 kHz to 1 710 kHz (10 kHz step) (FS-XA3UF)
1-way bass-reflex type
Magnetically shielded type
× 1
Ω
• Manufactured under license from Dolby Laboratories. "Dolby", "Pro Logic", "MLP lossless", and the double-D symbol are trademarks of Dolby
Laboratories.
• "DTS" and "DTS 2.0+ Digital Out" are trademarks of Digital Theater Systems, Inc.
• Official DivX® Certified product" "Plays all versions of DivX® video (including DivX® 6) with standard playback of DivX® media files" "DivX, DivX
certified, and associated logos are trademarks of DivX, Inc. and are used under licence.
• USE OF THIS PRODUCT IN ANY MANNER THAT COMPLIES WITH THE MPEG-4 VISUAL STANDARD IS PROHIBITED, EXCEPT FOR USE
BY A CONSUMER ENGAGING IN PERSONAL AND NON-COMMERCIAL ACTIVITIES.
• This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise
authorized by Macrovision. Reverse engineering or disassembly is prohibited.
• Designs and Specifications are subject to change without notice.
1-2 (No.MB546)
SECTION 1
PRECAUTION
1.1Safety Precautions
(1) This design of this product contains special hardware and
many circuits and components specially for safety purposes. For continued protection, no changes should be made
to the original design unless authorized in writing by the
manufacturer. Replacement parts must be identical to
those used in the original circuits. Services should be performed by qualified personnel only.
(2) Alterations of the design or circuitry of the product should
not be made. Any design alterations of the product should
not be made. Any design alterations or additions will void
the manufacturers warranty and will further relieve the
manufacture of responsibility for personal injury or property
damage resulting therefrom.
(3) Many electrical and mechanical parts in the products have
special safety-related characteristics. These characteristics are often not evident from visual inspection nor can the
protection afforded by them necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special
safety characteristics are identified in the Parts List of Service Manual. Electrical components having such features
are identified by shading on the schematics and by ( ) on
the Parts List in the Service Manual. The use of a substitute
replacement which does not have the same safety characteristics as the recommended replacement parts shown in
the Parts List of Service Manual may create shock, fire, or
other hazards.
(4) The leads in the products are routed and dressed with ties,
clamps, tubings, barriers and the like to be separated from
live parts, high temperature parts, moving parts and/or
sharp edges for the prevention of electric shock and fire
hazard. When service is required, the original lead routing
and dress should be observed, and it should be confirmed
that they have been returned to normal, after reassembling.
(5) Leakage shock hazard testing
After reassembling the product, always perform an isolation check on the exposed metal parts of the product (antenna terminals, knobs, metal cabinet, screw heads,
headphone jack, control shafts, etc.) to be sure the product
is safe to operate without danger of electrical shock.Do not
use a line isolation transformer during this check.
• Plug the AC line cord directly into the AC outlet. Using a
"Leakage Current Tester", measure the leakage current
from each exposed metal parts of the cabinet, particularly any exposed metal part having a return path to the
chassis, to a known good earth ground. Any leakage current must not exceed 0.5mA AC (r.m.s.).
• Alternate check method
Plug the AC line cord directly into the AC outlet. Use an
AC voltmeter having, 1,000Ω per volt or more sensitivity
in the following manner. Connect a 1,500Ω 10W resistor
paralleled by a 0.15µF AC-type capacitor between an ex-
posed metal part and a known good earth ground.
Measure the AC voltage across the resistor with the AC
voltmeter.
Move the resistor connection to each exposed metal
part, particularly any exposed metal part having a return
path to the chassis, and measure the AC voltage across
the resistor. Now, reverse the plug in the AC outlet and
repeat each measurement. Voltage measured any must
not exceed 0.75 V AC (r.m.s.). This corresponds to 0.5
mA AC (r.m.s.).
AC VOLTMETER
(Having 1000
ohms/volts,
or more sensitivity)
0.15 F AC TYPE
Place this
probe on
1500 10W
Good earth ground
1.2Warning
(1) This equipment has been designed and manufactured to
meet international safety standards.
(2) It is the legal responsibility of the repairer to ensure that
these safety standards are maintained.
(3) Repairs must be made in accordance with the relevant
safety standards.
(4) It is essential that safety critical components are replaced
by approved parts.
(5) If mains voltage selector is provided, check setting for local
voltage.
1.3Caution
Burrs formed during molding may be left over on some parts
of the chassis.
Therefore, pay attention to such burrs in the case of preforming repair of this system.
1.4Critical parts for safety
In regard with component parts appearing on the silk-screen
printed side (parts side) of the PWB diagrams, the parts that are
printed over with black such as the resistor ( ), diode ( )
and ICP ( ) or identified by the " " mark nearby are critical
for safety. When replacing them, be sure to use the parts of the
same type and rating as specified by the manufacturer.
(This regulation dose not Except the J and C version)
each exposed
metal part.
(No.MB546)1-3
1.5 Safety Precautions (U.K only)
(1) This design of this product contains special hardware and many circuits and components specially for safety purposes. For con-
tinued protection, no changes should be made to the original design unless authorized in writing by the manufacturer. Replacement parts must be identical to those used in the original circuits.
(2) Any unauthorised design alterations or additions will void the manufacturer's guarantee; furthermore the manufacturer cannot
accept responsibility for personal injury or property damage resulting therefrom.
(3) Essential safety critical components are identified by ( ) on the Parts List and by shading on the schematics, and must never
be replaced by parts other than those listed in the manual. Please note however that many electrical and mechanical parts in
the product have special safety related characteristics. These characteristics are often not evident from visual inspection. Parts
other than specified by the manufacturer may not have the same safety characteristics as the recommended replacement parts
shown in the Parts List of the Service Manual and may create shock, fire, or other hazards.
(4) The leads in the products are routed and dressed with ties, clamps, tubings, barriers and the like to be separated from live parts,
high temperature parts, moving parts and/or sharp edges for the prevention of electric shock and fire hazard. When service is
required, the original lead routing and dress should be observed, and it should be confirmed that they have been returned to
normal, after re-assembling.
1.5.1 Warning
(1) Service should be performed by qualified personnel only.
(2) This equipment has been designed and manufactured to meet international safety standards.
(3) It is the legal responsibility of the repairer to ensure that these safety standards are maintained.
(4) Repairs must be made in accordance with the relevant safety standards.
(5) It is essential that safety critical components are replaced by approved parts.
(6) If mains voltage selector is provided, check setting for local voltage.
Burrs formed during molding may be left over on some parts of the chassis. Therefore,
pay attention to such burrs in the case of preforming repair of this system.
1-4 (No.MB546)
1.6Preventing static electricity
Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser
diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.
1.6.1 Grounding to prevent damage by static electricity
Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as laser products.
Be careful to use proper grounding in the area where repairs are being performed.
(1) Ground the workbench
Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the
traverse unit (optical pickup) on it.
(2) Ground yourself
Use an anti-static wrist strap to release any static electricity built up in your body.
(caption)
Anti-static wrist strap
1M
Conductive material
(conductive sheet) or iron palate
(3) Handling the optical pickup
• In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical
pickup are shorted. After replacement, return the shorted parts to their original condition.
(Refer to the text.)
• Do not use a tester to check the condition of the laser diode in the optical pickup. The tester's internal power source can easily
destroy the laser diode.
1.7Handling the traverse unit (optical pickup)
(1) Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit.
(2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the
replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a
time when attaching it to the connector.
(3) Handle the flexible cable carefully as it may break when subjected to strong force.
(4) I t is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it.
1.8Attention when traverse unit is decomposed
*Please refer to "Disassembly method" in the text for the pickup unit.
• Apply solder to the short land sections before the card wire is disconnected from the connecto on the servo board. (If the card wire
is disconnected without applying solder, the pickup may be destroyed by static electricity.)
• In the assembly, be sure to remove solder from the short land sections after connecting the card wire.
Short land section
pickup
Card wire
Traverse mechanism assembly
(No.MB546)1-5
1.9Important for laser products
1.CLASS 1 LASER PRODUCT
2.CAUTION :
(For U.S.A.) Visible and/or invisible class II laser radiation
when open. Do not stare into beam.
(Others) Visible and/or invisible class 1M laser radiation
when open. Do not view directly with optical instruments.
3.CAUTION : Visible and/or invisible laser radiation when
open and inter lock failed or defeated. Avoid direct
exposure to beam.
4.CAUTION : This laser product uses visible and/or invisible
laser radiation and is equipped with safety switches which
prevent emission of radiation when the drawer is open and
the safety interlocks have failed or are defeated. It is
dangerous to defeat the safety switches.
5.CAUTION : If safety switches malfunction, the laser is able
to function.
6.CAUTION : Use of controls, adjustments or performance of
procedures other than those specified here in may result in
hazardous radiation exposure.
!
Please use enough caution not to
see the beam directly or touch it
in case of an adjustment or operation
check.
REPRODUCTION AND POSITION OF LABELS and PRINT
WARNING LABEL and PRINT
1-6 (No.MB546)
SECTION 2
SPECIFIC SERVICE INSTRUCTIONS
This service manual does not describe SPECIFIC SERVICE INSTRUCTIONS.
(No.MB546)1-7
SECTION 3
DISASSEMBLY
3.1Main body section
3.1.1 Removing the side panel L and side panel R
(See Figs.1 to 4)
(1) From the back side of the main body, remove the four
screws A attaching the side panels L/R. (See Fig.1.)
(2) From the bottom side of the main body, remove the four
screws B attaching the side panels L/R. (See Fig.2.)
(3) From the both sides of the main body, release the joint a in
the direction of the arrow and remove the side panels L/R
toward this side. (See Figs.3 and 4.)
a
Side panel R
A
Side panel R
Side panel R
Fig.1
Side panel L
B
A
a
Side panel L
Fig.3
a
a
Fig.4
Side panel L
1-8 (No.MB546)
B
Fig.2
3.1.2 Removing the top panel assembly
(See Figs.5 and 6)
• Remove the side panels L/R.
(1) From the both sides of the main body, remove the two
screws C. (See Figs.5 and 6)
(2) From the back side of the main body, remove the screw D
attaching the top panel assembly. (See Fig.6.)
(3) From the both sides of the main body, release the joints b
and c. (See Figs.5 and 6.)
(4) Take out the top panel assembly in the direction of the ar-
row. (See Fig.6.)
C
Top panel assembly
c
Fig.5
b
Top panel assembly
b
D
Fig.6
c
C
(No.MB546)1-9
3.1.3 Removing the front panel assembly
(See Figs.7 and 8)
• Remove the side panels L/R and top panel assembly.
(1) From the bottom side of the main body, remove the two
screws E attaching the front panel assembly. (See Fig.7.)
(2) From the forward side of the micom board, disconnect the
card wire from the connector CN426
(3) From the bottom and both sides of the main body, release
the joints (d, e) of the front panel assembly and remove the
front panel assembly in the direction of the arrow. (See
Figs.7 and 8.)
. (See Fig.8.)
Front panel assembly
E
CN426
d
Fig.7
Micom board
3.1.4 Removing the tuner
(See Fig.9)
• Remove the side panels L/R and top panel assembly.
(1) From the back side of the main body, remove the two
screws F attaching the tuner to the rear panel.
(2) Disconnect the card wire from the connector CN1
tuner.
on the
e
Fig.8
TunerRear panelCN1
F
Fig.9
1-10 (No.MB546)
3.1.5 Removing the rear panel
(See Fig.10)
• Remove the side panels L/R and top panel assembly.
(1) From the back side of the main body, remove the ten
screws G and screw H attaching the rear panel.
(2) From the top side of the main body, disconnect the earth
wire from the rear panel.
(3) From the both sides of the main body, release the joints f
and remove the rear panel.
3.1.6 Removing the switching power supply
(See Figs.10 and 11)
• Remove the side panels L/R and top panel assembly.
(1) From the back side of the main body, remove the screw H
attaching the rear panel. (See Fig.10.)
(2) From the top side of the main body, disconnect the wire
from the connector CN200
Fig.11.)
(3) From the left side of the main body, remove the screw J at-
taching the main body. (See Fig.11.)
(4) Take out the switching power supply. (See Fig.11.)
3.1.7 Removing the digital amplifier board assembly
(See Figs.11 and 12)
• Remove the side panels L/R, top panel assembly, rear panel
and switching power supply.
(1) From the top side of the main body, remove the screw K at-
taching the digital amplifier board assembly. (See Fig.11.)
Reference:
When attaching the screw K, attach the earth wire with it.
(2) From the left side of the main body, disconnect the connec-
tors (CN310
assembly from the regulator board. (See Fig.12.)
(3) Release the joint g of the shield case B in the direction of
the arrow and take out the digital amplifier board assembly
from the regulator board. (See Fig.12.)
, CN311, CN312) on the digital amplifier board
on the regulator board. (See
Earth wire
Rear panel
GG
G
G
Fig.10
Digital amplifier board assembly
H
ff
K
CN200
Switching power supply
Regulator board
CN312CN311CN310
g
Regulator board
J
Fig.11
Digital amplifier board assembly
Fig.12
(No.MB546)1-11
3.1.8 Removing the digital amplifier board
(See Figs.13 to 18)
• Remove the side panels L/R, top panel assembly, rear panel,
switching power supply and digital amplifier board assembly.
(1) From the forward side of the digital amplifier board assem-
bly, remove the screw M. (See Fig.13.)
(2) From the top and bottom sides of the digital amplifier board
assembly, remove the three screws N. (See Figs.14 and
15.)
(3) Release the joints (h, j, k, m) and remove the shield case
B with the heat sink in the direction of the arrow. (See
Figs.14 to 17.)
(4) From the forward side of the digital amplifier board, remove
the screw N attaching the heat sink. (See Fig.18.)
(5) Remove the solders from the soldered sections (n, p) and
bend the sections (q, r) of the shield case A in the direction
of the arrow. (See Fig.18.)
(6) Take out the digital amplifier board from the shield case A.
Shield case B
k
Fig.16
Heat sink
Digital amplifier board
M
Fig.13
h
N
Digital amplifier board
Shield case B
N
Fig.14
N
Shield case B
q
n
Heat sink
m
N
Fig.17
Shield case A
r
p
Shield case B
1-12 (No.MB546)
j
Digital amplifier board
Fig.18
Digital amplifier board
Fig.15
3.1.9 Removing the micom board
(See Fig.19)
• Remove the side panels L/R, top panel assembly, rear panel
and front panel assembly.
(1) From the right side of the main body, remove the screw P
attaching the micom board.
(2) Disconnect the card wire from the connector CN421
forward side of the micom board.
Reference:
Remove the tuner as required. (See Fig.9)
(3) Disconnect the wire from the connector CN501
ward side of the micom board.
(4) Disconnect the connectors (CN423
the micom board from the regulator and video boards toward this side to remove the micom board.
, CN424, CN425) on
on the
on the for-
CN421
Micom board
3.1.10 Removing the regulator board
(See Fig.20)
• Remove the side panels L/R, top panel assembly, tuner, rear
panel, switching power supply, digital amplifier board assembly and micom board.
(1) From the top side of the main body, disconnect the card
wires from the connectors (CN208
regulator board.
Reference:
When connecting the card wire to the connector CN208
pass it through the hole s of the regulator board as before.
(2) Remove the screws Q and Q'.
Reference:
When attaching the screw Q', attach the earth wire with
it.
(3) Remove the screws Q".
Reference:
When attaching the screw Q", attach the earth wire and
the wire holder with it.
(4) Remove the screw R and screw S' attaching the earth wire.
Reference:
When attaching the screw R and S', attach the earth wire
with it.
, CN210, CN212) on the
CN501
Regulator board
CN210
,
CN424CN423CN425
Q
P
Fig.19
CN212
R
S'
Video board
CN703
S
Q''
Wire holder
CN208
s
Q'
Fig.20
3.1.11 Removing the video board
(See Fig.20)
• Remove the side panels L/R, top panel assembly, tuner, rear
panel, switching power supply, digital amplifier board assembly and micom board.
Reference:
Remove the regulator board as required.
(1) From the top side of the main body, remove the two screws
S.
Reference:
When attaching the screw S, attach the earth wire with it.
(2) Take out the video board from the main body.
(3) Disconnect the card wire from the connector CN703
video board.
on the
(No.MB546)1-13
3.1.12 Removing the DVD mechanism assembly
(See Figs.21 to 23)
• Remove the side panels L/R, top panel assembly, front panel
assembly, tuner, rear panel, switching power supply, digital
amplifier board assembly, micom board and regulator board.
(1) From the right side of the main body, remove the screw T
attaching the metal chassis. (See Fig.21.)
(2) From the top side of the main body, remove the screw U
and take out the metal chassis. (See Fig.22.)
Reference:
When attaching the metal chassis, pass the card wire
through the hole t on the metal chassis as before.
(3) Disconnect the card wire from the connector CN703
video board. (See Fig.23.)
(4) Remove the three screws V and take out the DVD mecha-
nism assembly from the bottom chassis. (See Fig.23.)
on the
T
Metal chassis
Fig.21
t
Metal chassis
U
Fig.22
DVD mechanism assembly
V
V
Fig.23
CN703
Video board
1-14 (No.MB546)
3.1.13 Removing the switch board and front FL board
(See Figs.24 to 26)
• Remove the side panels L/R, top panel and front panel assem-
bly.
(1) From the front side of the main body, pull out the volume
knob assembly in the direction of the arrow. (See Fig.24.)
(2) From the inside of the front panel assembly, remove the
five screws W attaching the switch board. (See Fig.25.)
(3) Remove the six screws X attaching the front FL board.
(See Fig.26.)
(4) Take out the switch board and the front FL board.
Volume knob
assembly
Front panel
assembly
Fig.24
Switch board
W
Fig.25
Front FL board
X
Fig.26
(No.MB546)1-15
3.1.14 Removing the headphone board
(See Fig.27)
• Remove the side panels L/R, top panel assembly, front panel
assembly, tuner, rear panel, switching power supply, digital
amplifier board assembly, micom board, regulator board and
DVD mechanism assembly.
(1) Remove the three screws Y and take out the headphone
board.
(2) Take out the headphone board.
Headphone board
Y
Fig.27
1-16 (No.MB546)
3.2DVD mechanism section
• Remove the DVD mechanism assembly from the main body.
3.2.1 Removing the traverse mechanism assembly
(See Fig.1)
From the bottom side of the DVD mechanism assembly, remove
the four screws A attaching the traverse mechanism assembly
and take out the traverse mechanism assembly with the DVD
module board.
DVD mechanism assembly
Traverse mechanism assembly
AA
DVD module board
Fig.1
(No.MB546)1-17
3.2.2 Removing the DVD module board
(See Figs.2 and 3)
• Remove the traverse mechanism assembly.
(1) From the side of the traverse mechanism assembly, solder
the short land sections a on the DVD pickup. (See Fig.2.)
(2) From the bottom side of the traverse mechanism assem-
bly, release the lock of the connector CN101
module board in the direction of the arrow and disconnect
the card wire. (See Fig.3.)
Caution:
• Solder the short land sections a on the DVD pickup before disconnecting the card wire from the connector
on the DVD module board. If the card wire is
CN101
disconnected without attaching solder, the DVD pickup may be destroyed by static electricity. (See Figs.2
and 3.)
• When attaching the DVD module board, be sure to remove solders from the short land sections a after connecting the card wire to the connector CN101
DVD module board. (See Figs.2 and 3.)
(3) Disconnect the card wire from the connector CN201
DVD module board. (See Fig.3.)
(4) Remove the two screws B attaching the DVD module
board. (See Fig.3.)
(5) Remove the DVD module board from the engagement sec-
tion b in an upward and remove the engagement section c
in the direction of the arrow. (See Fig.3.)
on the DVD
on the
on the
a
Traverse mechanism assembly
Card wire
B
DVD pickup
Fig.2
Card wire
CN101CN201
b
c
DVD module board
B
Traverse mechanism assembly
Fig.3
1-18 (No.MB546)
3.2.3 Removing the DVD pickup
(See Figs.2,4 to 6)
• Remove the traverse mechanism assembly.
(1) From the side of the traverse mechanism assembly, solder
the short land sections a on the DVD pickup. (See Fig.2.)
(2) Release the lock of the connector on the DVD pickup in the
direction of the arrow and disconnect the card wire. (See
Fig.4.)
Caution:
• Solder the short land sections a on the DVD pickup before disconnecting the card wire from the connector on
the DVD pickup. If the card wire is disconnected without attaching solder, the DVD pickup may be destroyed by static electricity. (See Figs.2 and 4.)
• When attaching the DVD pickup, be sure to remove
solders from the short land sections a after connecting
the card wire to the connector on the DVD pickup.
(See Figs.2 and 4.)
(3) Remove the screw C and remove the feed bracket from the
sections d. (See Fig.4.)
(4) Release the claw e of the thrust spring in the direction of
the arrow and remove the thrust spring. (See Fig.4.)
(5) Remove the guide shaft of the DVD pickup from the section
f on the traverse mechanism assembly and remove the
guide shaft from the section g while moving it in the direction of the arrow. (See Fig.5.)
(6) Remove the DVD pickup from the section h of the traverse
mechanism assembly and take out the DVD pickup with
the guide shaft. (See fig.5.)
(7) From the bottom side of the DVD pickup, remove the two
screws D attaching the rack arm and rack arm spring. (See
Fig.6.)
(8) Pull the guide shaft out of the DVD pickup. (See Fig.6.)
e
f
Guide shaft
Traverse mechanism assembly
Torsion spring
DVD pickup
Fig.5
DVD pickup
h
Rack arm
g
Feed bracket
C
Card wire
Thrust spring
Thrust spring
Connector
Fig.4
Guide shaft
Rack arm spring
D
Fig.6
DVD pickup
(No.MB546)1-19
3.2.4 Attaching the DVD pickup
(See Figs.2,4 to 7)
• See "3.2.3 Removing the DVD pickup".
(1) Attach the guide shaft, rack arm and rack arm spring to the
DVD pickup. (See Fig.6.)
(2) Align the DVD pickup to the section h of the traverse mech-
anism assembly first, and set the both ends of the guide
shaft of the DVD pickup in the sections f and g of the
traverse mechanism assembly. (See Fig.5.)
Reference:
When attaching the guide shaft to the section g, attach it
under the rod spring. (See Fig.5.)
(3) Attach the feed bracket and thrust spring. (See Fig.4.)
(4) Remove solders from the short land sections a after con-
necting the card wire to the connector on the DVD pickup.
(See Figs.2 and 4.)
(5) Turn the screw shaft gear in the direction of the arrow 1 to
move the DVD pickup fully in the direction of the arrow 2.
(See Fig.7.)
Screw shaft gear
1
22
DVD pickup
Fig.7
1-20 (No.MB546)
3.2.5 Removing the feed motor
(See Figs.4,8 and 9)
• Remove the traverse mechanism assembly.
(1) From the top side of the traverse mechanism assembly, re-
move the screw C and remove the feed bracket from the
sections d. (See Fig.4.)
(2) Release the claw e of the thrust spring in the direction of
the arrow and remove the thrust spring. (See Fig.4.)
(3) Remove the wires from the soldered section j on the spin-
dle motor board. (See Fig.8.)
Reference:
• When attaching the feed motor, pass the wire through
the section k on the traverse mechanism assembly.
(See Fig.8.)
• Pass the wire through the lower section of the rod
spring. (See Fig.8.)
(4) Remove the screw shaft in the direction of the arrow. (See
Fig.8.)
(5) From the side of the traverse mechanism assembly, re-
move the screw E attaching the feed motor. (See Fig.8.)
(6) Take out the feed motor from the traverse mechanism as-
sembly.
3.2.6 Removing the spindle motor board
(See Figs.8 and 9)
• Remove the traverse mechanism assembly and DVD module
board.
(1) From the top side of the traverse mechanism assembly, re-
move the wires from the soldered section j on the spindle
motor board. (See Fig.8.)
(2) From the bottom side of the traverse mechanism assem-
bly, remove the three screws F attaching the spindle motor
board. (See Fig.9.)
Reference:
• When attaching the spindle motor board, pass the wire
through the section m on the traverse mechanism assembly.
(See Fig.9.)
• After attaching the screws F, apply bond as before.
E
Screw shaft
Traverse mechanism assembly
Traverse mechanism assembly
m
Wires
Spindle motor board
Fig.8
Rod spring
k
j
F
Spindle motor
board
F
Fig.9
(No.MB546)1-21
3.2.7 Removing the DVD loading switch board
(See Fig.10.)
(1) From the bottom side of the DVD mechanism assembly, re-
move the wires from the soldered sections n on the DVD
loading switch board.
(2) Remove the screw G attaching the DVD loading switch
board.
(3) Lift the DVD loading switch board while pressing the claw
p of the DVD mechanism assembly in the direction of the
arrow and remove it from the section q.
Reference:
Pass the wires through the section r after attaching the DVD
loading switch board to the DVD mechanism assembly.
3.2.8 Removing the loading motor
(See Figs.10 to 14)
(1) From the bottom side of the DVD mechanism assembly, re-
move the wires from the soldered section n on the DVD
loading switch board. (See Fig.10.)
(2) Remove the screw H attaching the tray assembly. (See
Fig.10.)
(3) From the right side of the DVD mechanism assembly, push
the slide cam and pull the tray assembly out of the DVD
mechanism assembly in the direction of the arrow. (See
Fig.11.)
(4) From the top side of the DVD mechanism assembly, re-
move the two screws J attaching the clamper base. (See
Fig.12.)
(5) Lift the clamper base in an upward direction to remove it
from the engagement sections s and remove the engagement sections t in the direction of the arrow. (See Fig.12.)
(6) Remove the two screws K attaching the tray assembly and
take out the tray assembly from the DVD mechanism assembly. (See Fig.13.)
(7) Remove the belt from the motor pulley. (See Fig.14.)
Note:
Take care not to attach grease on the belt.
(8) Remove the two screws M attaching the loading motor to
the DVD mechanism assembly and take out the loading
motor from the bottom side of the DVD mechanism assembly. (See Fig.14.)
Reference:
Pass the wires through the section r after attaching the loading
motor to the DVD mechanism assembly. (See Fig.10.)
DVD loading switch board
Wires
n
G
q
r
DVD mechanism assembly
Tray assembly
Slide cam
J
s
DVD mechanism assembly
Tray assembly
p
Fig.10
Fig.11
Clamper base
H
t
1-22 (No.MB546)
s
t
J
DVD mechanism assembly
Fig.12
DVD mechanism assembly
Tray assembly
K
Fig.13
Motor pulley
M
DVD mechanism assembly
Fig.14
Belt
(No.MB546)1-23
SECTION 4
ADJUSTMENT
*ATTENTION IN SERVICE OF DVD SECTION
(1) When pickup, flash rom, DVD module board were changed, initialize EEPROM all means.
(2) When full initialization was executed, execute learning with a DVD test disc by all means.
Test disc : VT-501, VT-502
Learning method : It is adjusted automatically by normal playback of a DVD disc.
4.1Test mode 1
ItemOperationManagement
TUNER AM switch to
9kHz-step
TUNER AM switch to
10kHz-step
Cold startCold start processing.STOP+'0'+AUDIO POWER (REMOCON)
Clock Fast ForwardMake the clock fast forward.STOP+'2'+AUDIO POWER (REMOCON)
Volume changeMake the volume from the min to max.STOP+'3'+AUDIO POWER (REMOCON)
Micon Version checkCheck the micon version.STOP+'9'+AUDIO POWER (REMOCON)
LCD all displayAll of the icons on the FL are lightened.STOP+'10'+AUDIO POWER (REMOCON)
Tray lockLoader-mecha is locked.
DVD test modeIn to the DVD test mode. Test mode contents is refer to
DVD initializeDVD module initialized.
DVD region confirm
mode
compulsion NTSC
mode
DVD region confirm
mode
(Only source TUNER AM)
( Only source TUNER AM)
EJECT is pushed ,
during pushing STOP at STAND-BY
AC input pushing PLAY + PAUSE [key]
3D PHONIC [key] during DVD test mode
AC input pushing B.SKIP I<< +
DVD/CD [key]
AC input pushing STOP + DVD/CD [key]
AC input pushing B.SKIP I<< +
DVD/CD [key]
AM frequency change to 9kHz at U & A-version.|<< [key] + POWER button
AM frequency change to 10kHz at U & A-version.>>| [key] + POWER button
EJECT processing isn't done by pushing EJECT key
at tray lock on state.
Then display to LOCKED / UNLOCKED.
EJECT is pushed , pushing STOP again , tray lock is off.
Back up to tray locked ON/OFF.
module spec.
DVD test mode is canceled by POWER OFF and except
source DVD.
FL segment is light on at initialize completed.
Into the DVD region confirm mode.
Display region code on FL.
Into the compulsive NTSC mode.
Hereafter , only first power-on , start by NTSC unrelated
NTSEL-SW. ( Send command to module )
Mode is clear at POWER OFF.
Into the DVD region confirm mode.
* DVD REGION CHECK CAN ONLY BEEN DISPLAY
DURING SYSTEM POWER ON IN DVD MODE
(WHEN DVD LSI P.ON).
Temporary display region code on FL for 5 seconds.
FL will display "REGION x" where x is the Region
number.
* IF THERE IS NO INFORMATION FEEDBACK,
SYS-CON WILL DISPLAY
"WAIT" BLINKING 0.5SEC ON & OFF.
* FL WILL DISPLAY "AREAxxRy" WHERE "AREAxx" is
the DESTINATION INFO & R is the REGION INFO
After 5 seconds, return to previous display.
4.2Test mode 2
4.2.1 To enter DVD TEST mode
1-24 (No.MB546)
(1) AC POWER OFF.
(2) Press and hold PLAY + PAUSE keys.
(3) AC POWER ON while holding PLAY + PAUSE keys.
(4) DVD Mecha will start in TEST MODE, FL will display:
Tx
xx is the received DESTINATION information. Display as follows:
xx = JC/1U/D/E/2U/3U/UB/UT/4U/UY/EE/UF
y = region number
v = study state information from DVD UNIT
w = initialization state from DVD UNIT
xyvw
4.2.2 To exit DVD TEST mode
(1) During TEST MODE (except for Device Key write & DVD Region Re-write), press POWER KEY .
(2) To exit TEST mode for Device Key Write & DVD Region Re-write, first AC OFF, then AC ON again to return to normal
state.
4.2.3 EEPROM INITIALIZATION
4.2.3.1NORMAL INITIALIZE
(1) During DVD TEST MODE, Press STOP key on remote control to start NORMAL EEPROM INITIALIZATION.
(2) When received status, FL will display:
Tx
xyvw
w = Initialization state from DVD UNIT.
4.2.3.2FULL INITIALIZE
(1) During DVD TEST MODE, Press >>| key on set 2 seconds control to start FULL EEPROM INITIALIZATION.
(2) When received status, FL will display:
Tx
xyvw
w = initialization state from DVD UNIT.
4.2.4 DEVICE KEY CHECKSUM DISPLAY
(1) During DESTINATION INFO display screen (1), press MENU key to enter DEVICE KEY CHECKSUM display.
FL will display (Example):
DK =
4.2.5 DVD CHECK MODES
xxxx
(1) Press MENU key again to enter CHECK MODE.
FL display:
CEHCK
Press '1' key on REMOTE CONTROL to START PLAYBACK.
FL display:
LPYABACK
Press '2' key on REMOTE CONTROL to perform SEARCH TNO+1.
FL display:
WBOBLE
(2 seconds)
Status: AA 00 cc cc jj jj
ccccjj jj
Press '3' key on REMOTE CONTROL to perform SEARCH TNO-1.
FL display:
CEHCK
Press '4' key on REMOTE CONTROL to light up CD_LD and display laser current.
FL display:
DCDLSLR
(2 seconds)
Status: AA 00 cc cc jj jj
ccccjj jj
(Static)
(No.MB546)1-25
Press '5' key on REMOTE CONTROL to light up DVD_LD and display laser current.
FL display:
VDDDLSLR
(2 seconds)
Status: AA 00 cc cc jj jj
ccccjj jj
(Static)
Press '6' key on REMOTE CONTROL to enter DVD x 2 JITTER MEASUREMENT MODE.
FL display:
ITJ1X
(2 seconds)
Status: AA 00 cc cc jj jj
ccccjj jj
(Static)
Press '7' key on REMOTE CONTROL to view EEPROM (MECHA) content in -1 address step.
FL display:
EPEBDW
(2 seconds)
Status: AA 00 cc cc jj jj
ccccjj jj
(Static)
Press '8' key on REMOTE CONTROL to view EEPROM (MECHA) content in +1 address step.
FL display:
EPEFDW
(2 seconds)
Status: AA 00 cc cc jj jj
ccccjj jj
(Static)
Press '9' key on REMOTE CONTROL to perform TEMPERATURE SENSOR VALUE.
FL display:
TE MP
(2 seconds)
Status: AA 00 cc cc jj jj
ccccjj jj
(Static)
Press '10' key on REMOTE CONTROL to perform SEARCH DVD_DL PARALLEL DISC DESIGNATED POSITION
and JITTER MEASUREMENT.
FL display:
VDD-DL
(2 seconds)
Status: AA 00 cc cc jj jj
ccccjj jj
(Static)
Press '0' key on REMOTE CONTROL to perform monitor output.
FL display:
OMNI RTO
(2 seconds)
Status: AA 00 cc cc jj jj
ccccjj jj
(Static)
Press '+10' key to INITIALIZE EEPROM (MECHA)
FL display:
NIIT
1-26 (No.MB546)
Press PLAY key on REMOTE CONTROL to start PLAYING and obtain LASER CURRENT and JITTER value.
FL display:
SRLJTI
Status: AA 00 cc cc jj jj
ccccjj jj
Press STOP key on REMOTE CONTROL to stop JITTER measurement.
Status: AA 00 cc cc jj jj
ccccjj jj
(2) During CHECK mode, at any time press MENU key to exit CHECK mode and return to starting screen of
DVD TEST MODE.
(2 seconds)
(Static)
(Static)
SECTION 5
TROUBLESHOOTING
This service manual does not describe TROUBLESHOOTING.
(No.MB546)1-27
Victor Company of Japan, Limited
Audio/Video Systems Category 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan
(No.MB546)
Printed in Japan
VPT
SCHEMATIC DIAGRAMS
COMPACT COMPONENT SYSTEM
FS-XA3UF,FS-XA1B,FS-XA1E
FS-XA1EN,FS-XA1EV
CD-ROM No.SML200607
CA-FSXA3
Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)
Contents
Block diagrams
Standard schematic diagrams
Printed circuit boards
COPYRIGHT 2006 Victor Company of Japan, Limited.
SP-FSXA3SP-FSXA3
CA-FSXA1SP-FSXA1SP-FSXA1
2-1
2-2
2-10 to 12
No.MB546SCH
2006/7
In regard with component parts appearing on the silk-screen printed side (parts side) of the PWB diagrams, the
parts that are printed over with black such as the resistor ( ), diode ( ) and ICP ( ) or identified by the " "
mark nearby are critical for safety.
Block diagram
Headphone and AUX input section
HPL/R
J620
J621
HPIN
AUXL1/R1
AUXIN
PHONES
AUX
Used for Area suffix B/E/EN/EV
FL display, Remocon and LED section
JS612
ENCODER
D6113,Q6111
BACK LED
FL+/-, 35V
FLBK, FLCLK
FL615
FL TUBE
FLDATA, FLLATCH
User control keys section
S6000 to S6003
S6005 to S6009
S6012
KEY MATRIX
VOL+/-
BKLED
D6110,Q6110
STANDBY LED
IC617
REMOCON
FW615
FW615
KEY1
KEY2
DVD servo and DVD system control section
A, B, C, D, E1+F1, E2+F2
PICKUP
UNIT
T+/F+/-
FM+/-, UOUT, VOUT
WOUT, COM
CN201CN101
E3+F3, E4+F4, RF+/-, LPC1, LPC2
LD(CD)
LD(DVD)
Q101 to Q104
LASER DRIVER
IC201
DRIVER
TRAVERSE
MECHANISM
MA0 to 11, MDQ0 to 15
BA0, BA1, DQM0, DQM1, MCK
IC505
NWE, NCSM, NRAS, NCAS
SDRAM
TO
TUNER PACK
STBLED
REMOCON
LPCO1, LPCO2
CDLDCUR, DVDLDCUR
SPDRV, TRSDRV
TRDRV, FODRV
FG, /DRVMUTE
/SPMUTE
TRVSW
X301
27MHz
SDA
SCL
WP
IC510
EEPROM
FW621
CN610
System control, volume, AHB circuit, HP. circuit
and subwoofer section
Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)
(Micon board)
D2037
L2000
C2004
C5371
D2036
CN200
C4500
C5172
C5374
R4500
R5371
CN421
C5173
R4502
C4502
R5817
R5277
C5275
W202
D5372
C5802
D2006
C2043
R5830
W204
Q2043
C5819
D2043
R5814
R5810
W201
R5811
C4602
C5810
C5818
R5821
Q5811
C2006
R5822
Q5371
C2002
D2045
D4600
R5826
R5824
C5811
Q5372
R5815
Q5373
Q2040
R5825
D4602
C5813
D2042
Q5814
R5374
R5376
C2003
C5804
C4600
R5829
C2042
C5820
R5832
C5372
D2012
R5372
R5392
R5398
CN422
C5812
D2072
C5814
D5371
C5373
D2011
CN300
R2045
L4001
CN424
(Regulator board)
HS200
C2010
L2050
D2010
D2071
R4057
R4065
C2011
C5912
R5660
C5660
C5622
J5001
R5653
C5500
C5502
C5401
C5404
R5661
C5402
CN425
C5916
B5660
R5916
R5668
R5663
R5662
C5604
C5400
R5652
C5504
C5666
B5650
R5650
IC550
C5506
C5508
R5670
C5403
C5405
D5670
C5650
D5650
C5602
C5409
D4058
C5406
C5654
C5507
D5501
C5407
C5408
C5505
R5601
C5274
R5610
C5509
C5410
C5174
Q5511
C5272
CN423
C5520
IC235
C5175
D2035
CN203
C5510
C5273
C2035
D2038
CN210
CN200
C2000
R4058
K4001
C2050
R4063
IC200
(Video board)
R4038
R4034
R4036
R4037
R4045
R4041
R4039
R4040
R4046
R4148
R4053
R4150
R4155
R4059
R4070
R4071
CP250
R4050
R4051
R4156
R4061
R4062
R4165
R4069
R4068
R4172
R4074
R4072
R4073
R4090
R4075
R4175
R4176
HS250
IC250
D2051
D2050
D2052
C2052
IC400
R4077
R4078
R4079
IC410
D2060
R4006
C4109
R4109
R4005
R4001
R4009
R4105
R4104
R4004
C4110
CN501
CN301
HS202
D2064
D2066
D2061
D2076
R4035
R4020
D2078
R4024
R4019
C2020
C4207
R4021
X4100
CN426
D4201
Q4202
R4023
R4203
D4202
R4122
C4208
C5750
EP700
CN705
(Digital amp board)
CN302
CN212
C2022
D2025
D2026
D2020
D2022
R2025
C2026
IC202
C2025
C2612
C2015
K2085
CN208
C2614
L2095
K2084
C2095
K2086
K2089
K2088
C2062
C2065
PP1
C7020
J702
C7024
C7022
R7009
R7011
R7010
C7025
CN310
CN311
R3041
C7023
C1106
Q3041
CN312
C7014
C1206
C3034
C3015
Q3002
R3036
R3042
Q3004
C1238
R1238
R1237
Q3007
C3025
L1102
R3037
R1138
R1137
C3012
C1111
R3023
R3031
C7015
C1138
C1109
R1129
R1102
R1113
IC111
R1112
C3019
C1101
Q3042
C3016
L1101
R1134
R3022
R3032
R1107
R3020
R3010
R3025
IC303
C1144
C1143
L7006
R1108
D3001
Q1103
R1101
C1104
C1132
R1136
C1125
IC113
C1141
R1106
R1111
C1108
R1122
C1105
R1143
C1142
C7016
C7021
R1110
R1117
R1142
C3020
C7006
C1123
R1131
C3013
R1133
Q1104
R1123
R1308
C1307
Q1102
Q1101
C1137
R1103
IC112
D1203
R1309
R1118
R1104
C1102
C1103
C1107
R1124
R1233
R1132
D1104
Q1201
R1231
L1281
R1310
Q1204
C3031
C3011
R1223
R1303
R1304
R1216
C1309
IC131
C1308
C1237
CN703
R1228
R1218
R1243
R1234
C1222
R1215
R1224
R1242
C1244
Q1202
R1232
R1202
R1213
R1212
C1208
IC123
C1305
J3001
C7005
R1210
IC121
C1242
C1243
C3021
Q1203
R1207
R1211
R1236
R1217
R1222
C1211
IC132
C1232
C1207
IC122
IC701
R1208
IC301
R1227
C1241
R1201
C1201
R3009
C1209
R3027
D3003
C1204
R3005
C1225
R1229
R1206
C1205
L1181
C7007
R1204
C1202
C1203
R1127
X3002
L1202
C1223
R1203
C3018
C3017
R3033
J701
IC302
R3008
R3003
X3001
L1201
C3026
C3022
R3034
B1182
EP701
CN702
R4084
R4080
R4026
R4022
R4018
R4106
R4000
Q2020
CN202
IC295
CN201
2-10
Main board
reverse side
Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)
EP701
CN702
C7032
C7018
R7007
R7027
R7028
R7021
R7022
(Digital amp board)
(Video board)
R7029
C7012
R7030
C7013
C7007
C7011
R7025
R7026
C7010
R7023
R7024
CN703
C3027
CN312
C3015
R3035
Q3005
CN311
C3025
K3005
R3019
R3016
R3015
K3003
Q3003
R3014
R3011
CN310
C1206
C1238
R1125
R1126
C1106
C7019
C7031
C1117
R3012
C1138
C1110
K3001
Q3002
C3019
C1130
R1120
K3004
R1116
C3016
Q3006
R3018
R3017
K3002
C1118
L1102
R1119
C3012
R3013
R3022
R1235
R1135
R3010
R3020
C1140
C7008
C1129
R1115
R7008
C3020
IC701
C1128
C1101
C7028
C1381
C1125
IC303
L1101
C1124
J701
C7006
C1286
C1145
C1302
C1105
R1105
R7006
C1284
C1134
C1115
C1113
L1281
C1234
C1114
C1123
C1282
C1116
C1126
C1127
R1301
C1301
C1303
C1222
C3013
C7017
L7006
C1285
C1233
C1304
R1311
C1184
C1229
C1217
C1228
C1308
C1310
C1307
B3001
C3031
C7016
R1302
C1281
C1215
J3001
C1133
C1214
C1306
L1181
C1245
C1213
C1205
C1201
C1283
C1210
C1225
L1202
C1218
R1220
C1224
C7015
C1181
C1186
R3029
C1230
C1226
R1219
C3021
R3006
X3002
R3007
C1240
C3022
C1227
C3005
R1205
C1183
C1182
R3004
C3010
C3006
C1223
C7014
C1185
C3017
L1201
C3003
C3009
C1216
J702
C3018
C3004
C3002
R1225
R1226
C7020
C3007
C3008
X3001
EP700
C7024
CN705
(Micon board)
Q4201
C4208
R4202
D4201
C5750
R5750
R4201
C4207
D4202
R4127
R4121
CN426
R4123
R4032
X4100
R4136
Q5750
C5918
C4113
R4033
C4112
R4138
R4102
C4110
C4210
C4111
CN501
R4137
R4002
C4000
R4042
R4152
R4066
R4003
R4043
R4052
R4103
R4054
R4166
R4171
R4169
R4064
R4067
K4001
CN424
R4044
CN422
C5814
R5820
C5820
L4001
R5831
C5812
C5373
C5813
Q5812
R5819
C4600
D5371
D4602
C5372
Q4601
C5830
C5804
C5815
C4707
R4601
C4602
R4600
D4600
R4604
R5823
C5817
R5813
R5375
R5373
R5275
Q4600
IC520
Q5810
C5811
R4602
C5810
C5816
Q5813
R5812
C5802
R5378
C4708
CN421
K4500
C5172
C5819
R5827
R5173
R5828
C5173
R5371
R5171
R5817
D5372
R5274
R5276
C5275
C5374
C5380
R5279
R5181
C5371
R5178
R5176
R5271
R5278
C5273
C5510
R5177
R5175
C5521
C5520
IC510
Q5511
R5610
R5377
R5179
CN210
R5507
C5175
R5273
R5281
CN423
R5172
R5272
C5509
R5174
C5505
R5601
C5174
C5531
C5272
C5532
C5410
C5530
C5274
C5602
C5408
D5501
R5407
C5603
C5409
C5407
C5507
R5406
IC500
C4058
R5405
D5670
C5405
D4058
IC560
Q5670
R5506
C5508
C5406
C5654
R5401
D5650
C5506
C5400
R5666
R5505
C5403
C5650
CN425
C5504
C5404
C5914
C5911
R5915
R5402
Q5912
C5604
R5901
C5402
C5912
R5664
C5500
C5401
C5916
C5666
R5721
C5913
R4400
C5711
C5710
R5404
R5902
J5000
R5711
C5662
C5652
R5654
R5504
R5661
R5720
C5917
R5710
R5403
C5622
C5502
C5660
R5502
R5912
R5913
R5911
R5503
C5720
Q5620
D5620
J5001
C5501
C5503
R5501
C5721
C5730
C5620
R5620
Q5913
R5914
C5915
R4402
CN428
(Regulator board)
D2006
L2000
C2004
R2047
Q2006
C2000
R2009
D2038
D2037
CN200
C2035
D2036
C2001
D2035
IC235
R2037
R2036
C2036
C2037
D2007
R2010
CN203
CN302
K2083
C2062
C2015
C2065
K2085
K2084
K2086
K2089
K2088
C2614
C2095
R2614
K2095
PP1
L2095
IC295
C2615
R2095
R2615
Q2613
Q2614
CN208
C2616
R2618
Q2612
R2613
C2613
CN201
C2612
C2027
R2617
R2074
R2616
R2612
IC202
Q2071
Q2070
C2025
R2070
D2025
R2025
C2026
D2026
R2071
R2073
R2075
R2072
D2022
Q2020
C2021
R2021
D2020
C2022
HS202
C2020
R2022
D2078
D2061
D2066
CN301
D2076
D2064
D2060
R2050
C2055
IC250
C2051
Q2050
HS250
R2052
C2052
D2052
CP250
IC200
D2050
C2012
R2051
C2050
L2050
CN202
HS200
D2010
D2072
C2011
D2012
C2010
D2071
CN300
R2045
D2011
R2041
R2040
Q2042
R2043
R2044
D2042
C2041
C2042
Q2041
D2045
C2040
R2042
C2003
R2008
Q2040
C2002
C2006
Q2043
Q2007
W201
W204
R2006
R2007
W202
D2043
R2046
C2043
2-11
FL board
Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)
(Switch board)
R6012
R6010
S6012
S6009
S6008
S6003
R6009
R6004
S6007
S6002
R6003
S6006
R6008
S6001
R6002
R6007
(Front FL board)
R6150
D6150
C6152
CN610
C6170
C6159
C6160
C6172
R6170
IC617
D6140
C6156
C6155
R6151
C6171
R6181
C6157
C6140
R6142
Q6140
C6158
C6150
C6151
C6121
D6113
C6113
R6113
FL615
Q6111
R6116
C6120
R6111
JS612
R6112
C6153
C6154
R6115
(Headphone board)
EP603
R6243
C6241
R6241
C6245
J621
C6243
R6242
C6242
R6244
C6244
EP602
C6230
C6228
C6229
K6216
R6221
R6220
C6226
C6231
R6222
K6214
K6213
C6225
K6215
J623
C6224
B6102
K6212
IC621
R6219
X6200
C6227
C6223
C6222
R6223
C6216
C6220
J620
C6221
K6200
C6204
R6216
R6217
C6218
C6219
R6218
C6201
R6215
R6214
C6214
K6205
Q6110
C6116
D6110
K6202
K6211
R6213
FW615
C6215
S6005
R6006
C6203
R6110
K6201
S6000
R6200
EP601
FW621
FW615
AUXIN
C6200
3.3V
USBR
DGND
USBL
HPR
AGND
HPL
HPIN
AUXL1
AGND
R6001
B6104
C6202
DVD board
Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)
forward side
C352
R373
C351
R372
R309
TP291
R346
R347
R342
R290
R341
C341
C318
C290
TP292
C354
C353
R319
R375
R308
R535
R371
TP391
R542
R541
IC510
C564
C559
C563
C551
C339
IC453
IC454
C455
R462
R458
TP334
TP330
TP329
TP328
C555
C456
R460
K501
C558
IC505
C556
R530
C554
C560
C557
C562
reverse side
C730
R734
K733
C777
K731
IC708
R733
R722
K726
K722
C728
R701
C206
C731
K732
D701
K751
C711
K723
C703
K756
K753
R220
R726
C729
C704
C259
C709
C713
C258
IC705
K755
DVD loader board
TP745
C261
C262
C203
C251
C350
R377
TP744
TP746
C260
R208
R204
C202
C204
R725
CN712
C310
TP742
TP743
C257
R207
R350
C334
TP731
TP738
TP741
TP227
R723
R721
R310
R383
R324
R325
C308
TP733
TP735
R254
R205
TP734
IC701
CN702
R384
R385
IC201
TP761
TP231
C740
R740
C739
CN703
TP737
TP736
TP732
R353
R316
R326
IC509
TP324
TP323
C331
C333
K709 K710
K708
K707
TP309
TP314
K711
R201
TP326
C332
C338
TP724
TP723
TP722
TP721
TP720
C263C264
TP307
TP308
R732
TP315
TP306
TP337
C323
C348
C347
TP338
R117
Q104
R118
R362
D301
R115
C321
C320
C322
C356
R352
R351
TP325
TP320
R112
R114
TP300
TP301
R340
R338
R339
R393
R337
R335
R116
C108
Q103
X301
TP305
TP725
R394
R336
R334
R392
C312
R113
R348
R349
TP303
C104
R111
C101
TP335
TP333
TP332
TP331
CN301
R102
C107
TP124
TP123
TP381
C328
C326
C325
C110
C303
R730
R731
C771
C103
TP112
TP109
TP110
TP111
TP718
TP719
R126
C102
C109
C359
C336
TP716
TP717
CN701
Q105
CN101
TP321
CN704
IC302
C304
TP713
TP714
R103
TP108
TP105
TP106
R101
TP107
TP711
Q101
K706
TP709
TP710
R105
R104
C324
C340
R202
K704
K705
TP707
TP708
C106
C217
R252
K703
TP703
TP705
R109
Q102
R108
TP226
K701
K702
TP701
R107
R106
TP201
C715
C714
R110
TP202
IC704
C741
C319
C349
TP203
R718
TP380
TP204
R255
TP220
R719
R715
R714
R720
TP702
C314
TP205
TP206
R251
TP221
R215
C337
C330
TP207
TP208
R214
IC703
R727
C335
TP101
C256
IC702
TP755
TP102
TP103
CN201
R213
R728
TP753
R322 R323
TP104
C210
TP751
TP752
R320 R321
TP748
TP749
R724
TP750
R374
R376
C309
TP747
C201
C774
R359
R360
K762
IC305
K713
K763
C770
K765
K712
R366
R365
R358
TH301
R713
R743
C380
C721
R306
R388
IC707
IC706
R367
C772
C778
C393
R712
R307
R318
C773
K720
R332
C316
R711
R327
R330
R345
C376
R331
C311
C313
C756
C755
C754
C752
C753
C305
R364
R357
C377
C378 C379
C386
R303
C306
IC301
C383
C300
R221
C701C702
C712
K721
C302
C708
R741
C211
R742
C745
K351
R259
C707
K352
R257
C742
C105
C706
C301
R127
R716
C744
K754
C382
R128
C743
C775
C381
R125
C776
K759
R729
K761
Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)
S1
C205
R206
R354
R355
C329
C374
C315
C372
C371
R219
C375
R356
C307
C373
R363
R361
2-12
CN1
< MEMO >
Victor Company of Japan, Limited
Audio/Video Systems Category 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan
(No.MB546SCH)
Printed in Japan
VPT
PARTS LIST
FS-XA3UF
FS-XA1B,FS-XA1E,FS-XA1EN,FS-XA1EV
* All printed circuit boards and its assemblies are not available as service parts.
MB546
- Contents -
Exploded view of general assembly and parts list (Block No.M1)
Speaker assembly and parts list(Front speaker) (Block No.M2)
DVD mechanism assembly and parts list (Block No.MJ)
DVD loading base assembly and parts list (Block No.MN)
Electrical parts list (Block No.01~04)
Packing materials and accessories parts list (Block No.M3)
3-2
3-6
3-7
3-9
3-11
3-20
3-1
Exploded view of general assembly and parts list
A
7
8
Block No.
M
M
1
M
66
72
F
B
D
43
only
FS-XA3UF
28
40
59
only
FS-X
35
26
F
62
39
71
G
43
Switch board
73
12
k
60
61
57
k
Front LF board
13
9
79
2
3
73
7
11
k
74
63
10
3
1
21
64
1
5
4
8
18
Headphone board
19
i
3-2
65
6
28
39
43
35
board
40
26
13
84
only
FS-XA3UF
m
85
14
35
30
31
87
76
56
F
54
70
55
54
53
55
e
Digital amp. board
86
32
37
58
34
47
D
B
n
29
36
A
49
52
51
48
50
24
23
25
27
C
14
45
g
34
41
j
d
c
g
a
b
41
h
43
81
i
43
38
82
b
m
Regulator board
Micom board
f
e
n
83
board
19
c
9
74
79
77
14
a
k
69
20
22
f
h
44
j
42
35
80
SW power supply board
78
k
33
46
75
D
71
15
16
G
C
A
Video board
d
17
E
E
67
i
68
72
3-3
General Assembly
Block No. [M][1][M][M]
Symbol No.Part No.Part NameDescriptionLocal
1GN10089-009AFRONT PANEL
2GN10088-004AFRONT COVERXA3UF
2GN10088-003AFRONT COVERXA1B,XA1E,XA1EN,XA1EV
3QYSSST3008ZATAP SCREWM3 x 8mm(x4)
4GN20191-001AJACK DOOR
5GN30172-003ADOOR COVERXA3UF
5GN30172-002ADOOR COVERXA1B,XA1E,XA1EN,XA1EV
6GN30006-012ASPACER
7E69897-002CUSHION(x2)
8GN40129-001AFOOT(x2)
9QYSDSF2606ZATAP SCREWM2.6 x 6mm(x6)
10GN40098-002ADOOR SPRING
11QYSDSF2606ZATAP SCREWM2.6 x 6mm
12GN30177-002ATOP BUTTON
13GN30006-032ASPACER
14QYSBSG3008EATAP SCREWM3 x 8mm(x3)
15GV10248-003ABOTTOM CHASSIS
16GN30006-033ASPACER
17QYSBSGY3006EATAP SCREWM3 x 6mm(x2)
18QYSBSG3006EATAP SCREWM3 x 6mm(x2)
19GN30173-001AHP BRACKET
20GV40573-001AMECHA HOLDER
21QYSBSGY3006EATAP SCREWM3 x 6mm(x3)
22QYSBSGY3006EATAP SCREWM3 x 6mm
23GV40575-001AHEAT SINK
24GV40509-001ATHERMAL SHEET
25QYSDST2606EATAP SCREWM2.6 x 6mm
26GV10249-002AMETAL CHASSIS
27GN30006-033ASPACER
28GV30682-003ASHIELD CASE A
29GV30683-002ASHIELD CASE B
30QYSBSGY3006EATAP SCREWM3 x 6mm(x2)
31QYSSST3008EATAP SCREWM3 x 8mm
32QYSBSGY3008EATAP SCREWM3 x 8mm
33QYSBSTG3006EATAP SCREWM3 x 6mm
34QYSDST2606EATAP SCREWM2.6 x 6mm(x3)
35GN30006-032ASPACER(x3)
36GV40616-001AHEAT SINK
37QYSDSG3008EATAP SCREWM3 x 8mm(x2)
38QYSDSG3008EATAP SCREWM3 x 8mm
39GV40624-002ABRACKET
40QYSBSGY3006EATAP SCREWM3 x 6mm(x2)
41QYSBSG3008EATAP SCREWM3 x 8mm(x3)
42QYSBSG3008EATAP SCREWM3 x 8mm(x2)
43GN30006-034ASPACER(x6)XA3UF
43GN30006-034ASPACER(x4)XA1B,XA1E,XA1EN,XA1EV
44QYSBSGY3008EATAP SCREWM3 x 8mm
45GN30006-035ASPACER
46GV40632-201ASPACER
47GN10093-010AREAR PANELXA3UF
47GN10093-008AREAR PANELXA1B,XA1E,XA1EN,XA1EV
48QYSBSGY3008EATAP SCREWM3 x 8mm
49QYSBSGY3008EATAP SCREWM3 x 8mm
50QYSBSGY3008EATAP SCREWM3 x 8mm
51QYSBSGY3008EATAP SCREWM3 x 8mm
52QYSBSGY3008EATAP SCREWM3 x 8mm
53QYSBSGY3008EATAP SCREWM3 x 8mm
54QYSBSGY3008EATAP SCREWM3 x 8mm(x2)
55QYSBSGY3008EATAP SCREWM3 x 8mm(x2)
56QYSBSGY3008EATAP SCREWM3 x 8mm
57GN30006-036ASPACER(x2)
58QAU0412-001TUNERXA3UF
58QAU0413-001TUNERXA1B,XA1E,XA1EN,XA1EV
59GN10090-002ATOP PANEL
60QYSDSF2606ZATAP SCREWM2.6 x 6mm(x5)
61QYSSST3006ZATAP SCREWM3 x 6mm(x2)
62GN30178-002ABUTTON PLATEXA3UF
62GN30178-003ABUTTON PLATEXA1B,XA1E,XA1EN,XA1EV
63GN20190-001AFRONT LENS
64GN40097-001AVOLUME CAP
65GN30175-001AVOLUME KNOB
66GN10091-002ASIDE PANEL L
67GN10092-002ASIDE PANEL R
68GV40623-201ADOLBY LABEL
3-4
Symbol No.Part No.Part NameDescriptionLocal
69GN30176-002ATRAY FITTINGXA3UF
69GN30176-001ATRAY FITTINGXA1B,XA1E,XA1EN,XA1EV
70QYSBSG3008EATAP SCREWM3 x 8mm
71QYSBSG3008EATAP SCREWM3 x 8mm(x4)
72QYSBSG3008EATAP SCREWM3 x 8mm(x4)
73QYSSSF3008ZATAP SCREWM3 x 8mm(x2)
74QUQ412-1807CJ-EFFC WIRE18pin 7cm
75QUQ210-1208DJ-EFFC WIRE12pin 8cm
76QUQ412-1109CJ-EFFC WIRE11pin 9cmXA3UF
76QUQ412-1509CJ-EFFC WIRE15pin 9cmXA1B,XA1E,XA1EN,XA1EV
77QUQ210-2508CJ-EFFC WIRE25pin 8cm
78QUQ210-0514CJ-EFFC WIRE5pin 14cm
79QUQ210-0511DJ-EFFC WIRE5pin 11cm
80QAL0813-002SW P.SUPPLY MOD
81QYSBSG3008ZATAP SCREWM3 x 8mm
82QYSBSG3008ZATAP SCREWM3 x 8mm
83QYSBSG3008ZATAP SCREWM3 x 8mm
84GN40117-001ACOPPER PLATEXA3UF
85QYSDST2604EATAP SCREWM2.6 x 4mm(x2)XA3UF
86GN40118-001APROTECT SHEETXA3UF
87LV43268-001ACCC LABELXA3UF
C1101QTE1J60-106ZE CAPACITOR10uF 63V
C1102NCB31HK-222XC CAPACITOR2200pF 50V K
C1103NCB31HK-222XC CAPACITOR2200pF 50V K
C1104NDC31HJ-471XC CAPACITOR470pF 50V J
C1105QTE1H46-475ZE CAPACITOR4.7uF 50V
C1106QTE1H53-106ZE CAPACITOR10uF 50V
C1107NCB31HK-122XC CAPACITOR1200pF 50V K
C1108NDC31HJ-331XC CAPACITOR330pF 50V J
C1109NDC31HJ-220XC CAPACITOR22pF 50V J
C1110NDC31HJ-220XC CAPACITOR22pF 50V J
C1111NDC 31HJ- 220XC CAPACITOR22pF 50V J
C1113NCB30JK-105XC CAPACITOR1uF 6.3V K
C1114NCB31EK-104XC CAPACITOR0.1uF 25V K
C1115NCB31EK-104XC CAPACITOR0.1uF 25V K
C1118NCB21HK-104XC CAPACITOR0.1uF 50V K
C1123QTE1H53-106ZE CAPACITOR10uF 50V
C1124NDC31HJ-101XC CAPACITOR100pF 50V J
C1125QFVF1HJ-684ZMF CAPACITOR0.68uF 50V J
C1126NCB21HK-104XC CAPACITOR0.1uF 50V K
C1127NCB21HK-104XC CAPACITOR0.1uF 50V K
C1128NCB21HK-104XC CAPACITOR0.1uF 50V K
C1129NCB21HK-104XC CAPACITOR0.1uF 50V K
C1130NCB21HK-104XC CAPACITOR0.1uF 50V K
Part No.Part NameDescriptionLocal
3-11
Symbol No.
Part No.Part NameDescriptionLocal
Symbol No.
Part No.Part NameDescriptionLocal
C1132NDC31HJ-181XC CAPACITOR180pF 50V J
C1133NDC31HJ-471XC CAPACITOR470pF 50V J
C1134NDC31HJ-471XC CAPACITOR470pF 50V J
C1137NCB21CK-105XC CAPACITOR1uF 16V K
C1138QTE1J60-106ZE CAPACITOR10uF 63V
C1140NCB31CK-104XC CAPACITOR0.1uF 16V K
C1141NCB31HK-102XC CAPACITOR1000pF 50V K
C1142NCB31HK-102XC CAPACITOR1000pF 50V K
C1143NCB31HK-102XC CAPACITOR1000pF 50V K
C1144NCB31HK-102XC CAPACITOR1000pF 50V K
C1181NDC31HJ-221XC CAPACITOR220pF 50V J
C1182NCB31HK-332XC CAPACITOR3300pF 50V K
C1184NDC31HJ-221XC CAPACITOR220pF 50V J
C1201QTE1H53-106ZE CAPACITOR10uF 50V
C1201QTE1J60-106ZE CAPACITOR10uF 63V
C1202NCB31HK-222XC CAPACITOR2200pF 50V K
C1203NCB31HK-222XC CAPACITOR2200pF 50V K
C1204NDC31HJ-471XC CAPACITOR470pF 50V J
C1205QTE1H46-475ZE CAPACITOR4.7uF 50V
C1206QTE1H53-106ZE CAPACITOR10uF 50V
C1207NCB31HK-122XC CAPACITOR1200pF 50V K
C1208NDC31HJ-331XC CAPACITOR330pF 50V J
C1209NDC31HJ-220XC CAPACITOR22pF 50V J
C1210NDC31HJ-220XC CAPACITOR22pF 50V J
C1211NDC31HJ-220XC CAPACITOR22pF 50V J
C1213NCB30JK-105XC CAPACITOR1uF 6.3V K
C1214NCB31EK-104XC CAPACITOR0.1uF 25V K
C1215NCB31EK-104XC CAPACITOR0.1uF 25V K
C1218NCB21HK-104XC CAPACITOR0.1uF 50V K
C1222QTE1V46-336ZE CAPACITOR33uF 35V
C1223QTE1H53-106ZE CAPACITOR10uF 50V
C1224NDC31HJ-101XC CAPACITOR100pF 50V J
C1225QFVF1HJ-684ZMF CAPACITOR0.68uF 50V J
C1226NCB21HK-104XC CAPACITOR0.1uF 50V K
C1227NCB21HK-104XC CAPACITOR0.1uF 50V K
C1228NCB21HK-104XC CAPACITOR0.1uF 50V K
C1229NCB21HK-104XC CAPACITOR0.1uF 50V K
C1230NCB21HK-104XC CAPACITOR0.1uF 50V K
C1232NDC31HJ-181XC CAPACITOR180pF 50V J
C1233NDC31HJ-471XC CAPACITOR470pF 50V J
C1234NDC31HJ-471XC CAPACITOR470pF 50V J
C1237NCB21CK-105XC CAPACITOR1uF 16V K
C1238QTE1H53-106ZE CAPACITOR10uF 50V
C1238QTE1J60-106ZE CAPACITOR10uF 63V
C1240NCB31CK-104XC CAPACITOR0.1uF 16V K
C1241NCB31HK-102XC CAPACITOR1000pF 50V K
C1242NCB31HK-102XC CAPACITOR1000pF 50V K
C1243NCB31HK-102XC CAPACITOR1000pF 50V K
C1244NCB31HK-102XC CAPACITOR1000pF 50V K
C1281NDC31HJ-221XC CAPACITOR220pF 50V J
C1282NCB31HK-332XC CAPACITOR3300pF 50V K
C1284NDC31HJ-221XC CAPACITOR220pF 50V J
C1301NCB30JK-105XC CAPACITOR1uF 6.3V K
C1302NCB31CK-104XC CAPACITOR0.1uF 16V K
C1303NCB31CK-104XC CAPACITOR0.1uF 16V K
C1304NCB31CK-104XC CAPACITOR0.1uF 16V K
C1305NCB31EK-104XC CAPACITOR0.1uF 25V K
C1306NCB31EK-104XC CAPACITOR0.1uF 25V K
C1307QTMN1EM-477ZE CAPACITOR470uF 25V M
C1308QTE1H60-226ZE CAPACITOR22uF 50V
C1309NFV41HJ-333XMPPS CAPACITOR0.033uF 50V J
C1310NCB31CK-104XC CAPACITOR0.1uF 16V K
C1381NDC31HJ-101XC CAPACITOR100pF 50V J
C2000QTE1E46-476ZE CAPACITOR47uF 25V
C2002QFG32AJ-223ZPP CAPACITOR0.022uF 100V J
C2003QTE1E61-828E CAPACITOR8200uF 25V
C2004QTE1E46-476ZE CAPACITOR47uF 25V
C2004QTE1E60-476ZE CAPACITOR47uF 25V
C2006QETN1HM-226ZE CAPACITOR22uF 50V M
C2010QETN1EM-476ZE CAPACITOR47uF 25V M
C2011QTE1E60-476ZE CAPACITOR47uF 25V
C2012NCB31CK-104XC CAPACITOR0.1uF 16V K
XA1B,
XA1E,
XA1E
N,XA1
EV
XA3UF
XA3UF
XA1B,
XA1E,
XA1E
N,XA1
EV
XA3UF
C2015QETN1CM-107ZE CAPACITOR100uF 16V M
C2020QETN1EM-107ZE CAPACITOR100uF 25V M
C2021NCB31CK-104XC CAPACITOR0.1uF 16V K
C2022QETN1CM-107ZE CAPACITOR100uF 16V M
C2025QETN1CM-107ZE CAPACITOR100uF 16V M
C2026QETN1CM-476ZE CAPACITOR47uF 16V M
C2027NCB31HK-103XC CAPACITOR0.01uF 50V K
C2035QETN1CM-107ZE CAPACITOR100uF 16V M
C2036NCB31HK-103XC CAPACITOR0.01uF 50V K
C2037NCB31CK-104XC CAPACITOR0.1uF 16V K
C2040NCB31HK-103XC CAPACITOR0.01uF 50V K
C2041NCB31HK-103XC CAPACITOR0.01uF 50V K
C2042QETN1EM-476ZE CAPACITOR47uF 25V M
C2043QETN1EM-476ZE CAPACITOR47uF 25V M
C2050QETN1EM-107ZE CAPACITOR100uF 25V M
C2051NCB31CK-104XC CAPACITOR0.1uF 16V K
C2052QETN1CM-477ZE CAPACITOR470uF 16V M
C2055NCB31CK-104XC CAPACITOR0.1uF 16V K
C2062QETN1CM-476ZE CAPACITOR47uF 16V M
C2065QETN1CM-476ZE CAPACITOR47uF 16V M
C2095QETN1CM-476ZE CAPACITOR47uF 16V M
C2612QTE1J60-106ZE CAPACITOR10uF 63V
C2614QTE1J60-106ZE CAPACITOR10uF 63V
C2616NCB31CK-104XC CAPACITOR0.1uF 16V K
C3002NDC31HJ-471XC CAPACITOR470pF 50V J
C3003NDC31HJ-471XC CAPACITOR470pF 50V J
C3004NDC31HJ-471XC CAPACITOR470pF 50V J
C3005NDC31HJ-471XC CAPACITOR470pF 50V J
C3006NCB30JK-105XC CAPACITOR1uF 6.3V K
C3007NCB30JK-105XC CAPACITOR1uF 6.3V K
C3008NDC31HJ-331XC CAPACITOR330pF 50V J
C3009NDC31HJ-331XC CAPACITOR330pF 50V J
C3010NDC31HJ-470XC CAPACITOR47pF 50V J
C3011NCB31CK-104XC CAPACITOR0.1uF 16V K
C3012QFVF1HJ-334ZMF CAPACITOR0.33uF 50V J
C3013QETN1EM-107ZE CAPACITOR100uF 25V M
C3015QER61HM-106ZE CAPACITOR10uF 50V M
C3016QER61HM-106ZE CAPACITOR10uF 50V M
C3017QER61HM-106ZE CAPACITOR10uF 50V M
C3018QER61HM-106ZE CAPACITOR10uF 50V M
C3019QFVF1HJ-474ZMF CAPACITOR0.47uF 50V J
C3020QFVF1HJ-474ZMF CAPACITOR0.47uF 50V J
C3021QFVF1HJ-474ZMF CAPACITOR0.47uF 50V J
C3022QFVF1HJ-474ZMF CAPACITOR0.47uF 50V J
C3025QER61HM-106ZE CAPACITOR10uF 50V M
C3026NCB31CK-104XC CAPACITOR0.1uF 16V K
C3027NCB31CK-104XC CAPACITOR0.1uF 16V K
C3031QTE1H53-106ZE CAPACITOR10uF 50V
C3034NCB30JK-105XC CAPACITOR1uF 6.3V K
C4000NCB31CK-104XC CAPACITOR0.1uF 16V K
C4058QEKC1HM-475ZE CAPACITOR4.7uF 50V M
C4109NCB31HK-103XC CAPACITOR0.01uF 50V K
C4110QETN1CM-107ZE CAPACITOR100uF 16V M
C4111NCB31CK-104XC CAPACITOR0.1uF 16V K
C4112NDC31HJ-220XC CAPACITOR22pF 50V J
C4113NDC31HJ-220XC CAPACITOR22pF 50V J
C4207QETN0JM-107ZE CAPACITOR100uF 6.3V M
C4208QETN1HM-475ZE CAPACITOR4.7uF 50V M
C4210NCB30JK-105XC CAPACITOR1uF 6.3V K
C4500NDC31HJ-181XC CAPACITOR180pF 50V J
C4502NDC31HJ-181XC CAPACITOR180pF 50V J
C4600QETN1EM-476ZE CAPACITOR47uF 25V M
C4602QETN1EM-476ZE CAPACITOR47uF 25V M
C4707NCB31CK-104XC CAPACITOR0.1uF 16V K
C4708NCB31CK-104XC CAPACITOR0.1uF 16V K
C5172QFVF1HJ-474ZMF CAPACITOR0.47uF 50V J
C5173QFZ0225-473ZMYLAR CAPA0.047uF
C5174QFZ0225-473ZMYLAR CAPA0.047uF
C5175QTE1H53-106ZE CAPACITOR10uF 50V
C5272QFVF1HJ-474ZMF CAPACITOR0.47uF 50V J
C5273QFZ0225-473ZMYLAR CAPA0.047uF
C5274QFZ0225-473ZMYLAR CAPA0.047uF
C5275QTE1H53-106ZE CAPACITOR10uF 50V
C5371QETN1CM-107ZE CAPACITOR100uF 16V M
C5372QETN1HM-106ZE CAPACITOR10uF 50V M
C5373QETN1HM-105ZE CAPACITOR1uF 50V M
C5374QTE1E46-476ZE CAPACITOR47uF 25V
C5374QTE1E60-476ZE CAPACITOR47uF 25V
XA3UF
3-12
Symbol No.
Part No.Part NameDescriptionLocal
Symbol No.
Part No.Part NameDescriptionLocal
C5400QETN1HM-475ZE CAPACITOR4.7uF 50V M
C5401QETN1HM-475ZE CAPACITOR4.7uF 50V M
C5403QTE1J60-106ZE CAPACITOR10uF 63V
C5404QETN1HM-475ZE CAPACITOR4.7uF 50V M
C5405QFZ0225-473ZMYLAR CAPA0.047uF
C5406QTE1H53-106ZE CAPACITOR10uF 50V
C5407QTE1H53-106ZE CAPACITOR10uF 50V
C5408QFG32AJ-272ZPP CAPACITOR2700pF 100V J
C5409QFLC1HJ-104ZM CAPACITOR0.1uF 50V J
C5410QFLC1HJ-104ZM CAPACITOR0.1uF 50V J
C5500QETN1HM-475ZE CAPACITOR4.7uF 50V M
C5501QETN1HM-475ZE CAPACITOR4.7uF 50V M
C5503QTE1J60-106ZE CAPACITOR10uF 63V
C5504QETN1HM-475ZE CAPACITOR4.7uF 50V M
C5505QFZ0225-473ZMYLAR CAPA0.047uF
C5506QTE1H53-106ZE CAPACITOR10uF 50V
C5507QTE1H53-106ZE CAPACITOR10uF 50V
C5508QFG32AJ-272ZPP CAPACITOR2700pF 100V J
C5509QFLC1HJ-104ZM CAPACITOR0.1uF 50V J
C5510QFLC1HJ-104ZM CAPACITOR0.1uF 50V J
C5520QTE1E46-476ZE CAPACITOR47uF 25V
C5521NCB31CK-104XC CAPACITOR0.1uF 16V K
C5530NDC31HJ-101XC CAPACITOR100pF 50V J
C5531NDC31HJ-101XC CAPACITOR100pF 50V J
C5532NDC31HJ-101XC CAPACITOR100pF 50V J
C5602QTE1C46-107ZE CAPACITOR100uF 16V
C5603NCB31HK-103XC CAPACITOR0.01uF 50V K
C5604QTE1H60-226ZE CAPACITOR22uF 50V
C5620QETN1CM-107ZE CAPACITOR100uF 16V M
C5622QETN1CM-107ZE CAPACITOR100uF 16V M
C5650QETN1HM-225ZE CAPACITOR2.2uF 50V M
C5652QETN1CM-476ZE CAPACITOR47uF 16V M
C5654QETN1CM-476ZE CAPACITOR47uF 16V M
C5660QETN1HM-225ZE CAPACITOR2.2uF 50V M
C5662QETN1CM-476ZE CAPACITOR47uF 16V M
C5666QETN1HM-106ZE CAPACITOR10uF 50V M
C5667NDC31HJ-101XC CAPACITOR100pF 50V J
C5668NDC31HJ-101XC CAPACITOR100pF 50V J
C5669NCB31CK-224XC CAPACITOR0.22uF 16V K
C5710NDC31HJ-221XC CAPACITOR220pF 50V J
C5711NDC31HJ-221XC CAPACITOR220pF 50V J
C5720NDC31HJ-221XC CAPACITOR220pF 50V J
C5721NDC31HJ-221XC CAPACITOR220pF 50V J
C5730NCB31HK-103XC CAPACITOR0.01uF 50V K
C5802QETN1HM-106ZE CAPACITOR10uF 50V M
C5804QETN1HM-106ZE CAPACITOR10uF 50V M
C5810QETN1HM-475ZE CAPACITOR4.7uF 50V M
C5811QETN1HM-475ZE CAPACITOR4.7uF 50V M
C5812QETN1HM-475ZE CAPACITOR4.7uF 50V M
C5813QETN1CM-107ZE CAPACITOR100uF 16V M
C5814QETN1EM-476ZE CAPACITOR47uF 25V M
C5815NCB31HK-222XC CAPACITOR2200pF 50V K
C5816NDC31HJ-151XC CAPACITOR150pF 50V J
C5817NCB31HK-222XC CAPACITOR2200pF 50V K
C5818NDC31HJ-151XC CAPACITOR150pF 50V J
C5819QETN1AM-227ZE CAPACITOR220uF 10V M
C5820QETN1AM-227ZE CAPACITOR220uF 10V M
C5830NCB31HK-103XC CAPACITOR0.01uF 50V K
C5912QETN1HM-106ZE CAPACITOR10uF 50V M
C5913NCB31CK-104XC CAPACITOR0.1uF 16V K
C5914NCB31CK-104XC CAPACITOR0.1uF 16V K
C5915NCF21CZ-105XC CAPACITOR1uF 16V Z
C5916QETN1HM-106ZE CAPACITOR10uF 50V M
C7005NCB31CK-104XC CAPACITOR0.1uF 16V K
C7006QETN0JM-477ZE CAPACITOR470uF 6.3V M
C7007QETN1EM-226ZE CAPACITOR22uF 25V M
C7008NCB31CK-104XC CAPACITOR0.1uF 16V K
C7010NCB30JK-105XC CAPACITOR1uF 6.3V K
C7011NCB30JK-105XC CAPACITOR1uF 6.3V K
C7012NCB30JK-105XC CAPACITOR1uF 6.3V K
C7013NCB30JK-105XC CAPACITOR1uF 6.3V K
C7014QETN0JM-477ZE CAPACITOR470uF 6.3V M
C7015QETN0JM-477ZE CAPACITOR470uF 6.3V M
C7016QETN0JM-477ZE CAPACITOR470uF 6.3V M
C7017NDC31HJ-181XC CAPACITOR180pF 50V J
C7018NDC31HJ-181XC CAPACITOR180pF 50V J
C7019NDC31HJ-181XC CAPACITOR180pF 50V J
C7020QETN0JM-477ZE CAPACITOR470uF 6.3V M
C7021NCB31CK-104XC CAPACITOR0.1uF 16V K
C7022NDC31HJ-181XC CAPACITOR180pF 50V J
C7023NDC31HJ-181XC CAPACITOR180pF 50V J
C7024QETN0JM-477ZE CAPACITOR470uF 6.3V M
C7025NDC31HJ-181XC CAPACITOR180pF 50V J
C7028NDC31HJ-181XC CAPACITOR180pF 50V J
C7031NCB31HK-103XC CAPACITOR0.01uF 50V K
L1101QQLZ037-220COIL22uH
L1102QQLZ037-220COIL22uH
L1181QQR0797-002COIL
L1201QQLZ037-220COIL22uH
L1202QQLZ037-220COIL22uH
L1281QQR0797-002COIL
L2000QQLZ003-1R0COIL1uH
L2050QQL50AK-221ZCOIL220uH K
L2095QQL231K-4R7YINDUCTOR4.7uH K
L4001QQL244K-100ZCOIL10uH K
L7006QQL25CK-221ZCOIL220uH K
C101NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C102NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C103NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C104NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C105NEAF0JM-476XE CAPACITOR47uF 6.3V M
C106NBE20JM-226XTA E CAPACITOR22uF 6.3V M
C107NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C108NBE20JM-226XTA E CAPACITOR22uF 6.3V M
C201NDC31HJ-221XC CAPACITOR220pF 50V J
C202NDC31HJ-221XC CAPACITOR220pF 50V J
C203NCB31HK-103XC CAPACITOR0.01uF 50V K
C204NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C205NCB31HK-271XC CAPACITOR270pF 50V K
C206NDC31HJ-151XC CAPACITOR150pF 50V J
C210NCF31AZ-105XC CAPACITOR1uF 10V Z
C211NCB31HK-223XC CAPACITOR0.022uF 50V K
C217NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C251NCB31AK-474XC CAPACITOR0.47uF 10V K
C256NCB31CK-104XC CAPACITOR0.1uF 16V K
Part No.Part NameDescriptionLocal
3-16
Symbol No.
Part No.Part NameDescriptionLocal
Symbol No.
Part No.Part NameDescriptionLocal
C257NCB31HK-822XC CAPACITOR8200pF 50V K
C258NCB31CK-153XC CAPACITOR0.015uF 16V K
C259NCB31CK-153XC CAPACITOR0.015uF 16V K
C260NCB31HK-223XC CAPACITOR0.022uF 50V K
C261NCB31HK-223XC CAPACITOR0.022uF 50V K
C262NCB31HK-223XC CAPACITOR0.022uF 50V K
C263NEAF1CM-107XE CAPACITOR100uF 16V M
C300NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C301NEAF0GM-227XE CAPACITOR220uF 4V M
C302NEAF0GM-476XE CAPACITOR47uF 4V M
C303NBE20JM-476XTA E CAPACITOR47uF 6.3V M
C304NCB30JK-105XC CAPACITOR1uF 6.3V K
C305NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C306NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C307NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C308NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C309NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C310NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C312NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C313NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C314NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C315NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C316NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C318NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C319NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C320NCB31CK-104XC CAPACITOR0.1uF 16V K
C321NCB31CK-104XC CAPACITOR0.1uF 16V K
C322NCB31CK-104XC CAPACITOR0.1uF 16V K
C323NCB31CK-104XC CAPACITOR0.1uF 16V K
C324NCB30JK-105XC CAPACITOR1uF 6.3V K
C325NDC31HJ-120XC CAPACITOR12pF 50V J
C326NDC31HJ-100XC CAPACITOR10pF 50V J
C328NCB31HK-103XC CAPACITOR0.01uF 50V K
C329NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C330NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C331NCB31CK-333XC CAPACITOR0.033uF 16V K
C332NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C333NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C334NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C335NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C337NCB31CK-183XC CAPACITOR0.018uF 16V K
C338NCB31HK-562XC CAPACITOR5600pF 50V K
C339NBE20JM-106XTA E CAPACITOR10uF 6.3V M
C340NCB30JK-105XC CAPACITOR1uF 6.3V K
C341NCB30JK-105XC CAPACITOR1uF 6.3V K
C347NCB31CK-104XC CAPACITOR0.1uF 16V K
C348NCB31CK-104XC CAPACITOR0.1uF 16V K
C349NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C350NCB31HK-103XC CAPACITOR0.01uF 50V K
C351NCB31HK-103XC CAPACITOR0.01uF 50V K
C352NCB31CK-153XC CAPACITOR0.015uF 16V K
C353NCB31HK-561XC CAPACITOR560pF 50V K
C354NCB31HK-561XC CAPACITOR560pF 50V K
C356NCB30JK-105XC CAPACITOR1uF 6.3V K
C359NCB30JK-105XC CAPACITOR1uF 6.3V K
C371NCF31AZ-105XC CAPACITOR1uF 10V Z
C372NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C375NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C376NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C377NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C379NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C380NCB21CK-105XC CAPACITOR1uF 16V K
C381NCB21AK-225XC CAPACITOR2.2uF 10V K
C382NCB31HK-471XC CAPACITOR470pF 50V K
C383NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C386NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C393NCB31HK-103XC CAPACITOR0.01uF 50V K
C455NCB31HK-103XC CAPACITOR0.01uF 50V K
C551NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C554NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C555NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C557NCB31HK-102XC CAPACITOR1000pF 50V K
C558NBE20JM-226XTA E CAPACITOR22uF 6.3V M
C559NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C560NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C562NCF31AZ-105XC CAPACITOR1uF 10V Z
C563NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C564NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C701NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C704NEAF0JM-476XE CAPACITOR47uF 6.3V M
C706NEAF1CM-106XE CAPACITOR10uF 16V M
C707NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C711NCB21CK-105XC CAPACITOR1uF 16V K
C712NCB31HK-103XC CAPACITOR0.01uF 50V K
C713NCB21CK-105XC CAPACITOR1uF 16V K
C740NCB31CK-104XC CAPACITOR0.1uF 16V K
No additional / supplemental order of WARRANTY CARDs are available.
Block No.
M
3
M
M
P6
P13
P2
A2
A5
FS-XA1E,FS-XA1EN,
FS-XA1EV
P5
A1, A3, A4,
A6, A7, A8, A9
P4
P9
P8
P7
FS-XA1B
P5
A1, A3, A4,
A6, A7, A8,
A9, A11
FS-XA3UF
P5
A1, A3, A4,
A6, A7, A8,
A9, A12, A13,
A14, A15
P9
P8
P9
P8
P12
A10
P11
P3
P10
P14
P1
3-20
Packing and Accessories
Block No. [M][3][M][M]
Symbol No.Part No.Part NameDescriptionLocal
A 1GNT0067-006AINST BOOKCHI(PEKIN)XA3UF
A 1GNT0067-001AINST BOOKENGXA1B
A 1GNT0067-002AINST BOOKGER FRE DUT ITAXA1E
A 1GNT0067-003AINST BOOKSPA POR SWE FIN DANXA1EN
A 1GNT0067-004AINST BOOKPOL HUN CZEXA1EV
A 2QAL0014-003AM LOOP ANT
A 3QAL0457-001ANT.WIRE
A 4------------WARRANTY CARDBT-59019-1XA3UF
A 4------------WARRANTY CARDBT-54028-1XA1B,XA1E,XA1EN,XA1EV
A 5RM-SFSXA1AREMOCONXA3UF
A 5RM-SFSXA1RREMOCONXA1B,XA1E,XA1EN,XA1EV
A 6------------BATTERY1.5V(x2)
A 7QMPS230-183-JCPOWER CORD(EU)1.83m BLACKXA3UF
A 7QMPP060-183-JDPOWER CORD(EU)1.83m BLACKXA1B
A 7QMPL060-183-JDPOWER CORD(EU)1.83m BLACKXA1E,XA1EN,XA1EV
A 8QAM0530-001SPEAKER CORD
A 9QAM0216-001SIGNAL CORD
A 10SPFSXA3U-SPBOXSPEAKER BOX(x2)XA3UF
A 10SPFSXA1E-SPBOXSPEAKER BOX(x2)XA1B,XA1E,XA1EN,XA1EV
A 11VNA3000-204REGIST CARDXA1B
A 12BT-59020-1HOLOGRAM SEALXA3UF
A 13BT-59021-6CSVC CENTER LISTXA3UF
A 14E310162-001CERTIFICATE TAGXA3UF
A 15GN30020-004ASURVEY CARDXA3UF
P 1GN10108-002APACKING CASEXA3UF
P 1GN10094-014APACKING CASEXA1B,XA1E,XA1EN,XA1EV
P 2GN10095-001ACUSHION TOP
P 3GN10096-001ACUSHION BOTTOM
P 4QPC04504515PPOLY BAG45cm x 45cm
P 5QPC02503515PPOLY BAG25cm x 35cm
P 6QPA01702503PPOLY BAG17cm x 25cm
P 7GV40437-004ACLOTH
P 8QPC01401830POLY BAG14cm x 18cm
P 9GV40237-209ACARTON SPACER
P 10GN40122-001AUF CARTON SPACEXA3UF
P 118500061681POLY BAG(x2)XA3UF
P 118500051931POLY BAG(x2)XA1B,XA1E,XA1EN,XA1EV
P 128500060051NONWOVENS SHEET(x2)XA3UF
P 128500048041MIRROR MAT(x2)XA1B,XA1E,XA1EN,XA1EV
P 13LV22391-001ATOP CUSHIONXA3UF
P 13LV21976-001ATOP CUSHIONXA1B,XA1E,XA1EN,XA1EV
P 14LV22391-002ABOTTOM CUSHIONXA3UF
P 14LV21976-002ABOTTOM CUSHIONXA1B,XA1E,XA1EN,XA1EV
3-21
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.