JVC GZ-MG50E, EK, GZ-MG30E, GZ-MG20E service manual
ENGLISH
HARD DISK CAMCORDER
GZ-MG50E/EK
GZ-MG40E/EK
GZ-MG30E/EK
GZ-MG20E/EK
GETTING STARTED
VIDEO RECORDING &
PLAYBACK
STILL IMAGE RECORDING
& PLAYBACK
ADVANCED OPERATIONS
MENU SETTINGS
REFERENCES
7
22
28
31
48
52
INSTRUCTIONS
To deactivate the demonstration,
set “DEMO MODE” to “OFF”.
(
墌 pg. 48)
LYT1472-001C
EN
2 EN
Major Features of this Camera
Built-in Hard Disk
This hard disk camera records images to a
large, built-in hard disk drive (HDD) instead of a
DV tape like conventional video cameras. This
enables extended hours of high-resolution,
MPEG2 video recording.
Various Recording Modes
You can select the most suitable recording mode
for picture quality, image size, recording time,
and computer environment. (墌 pg. 62)
Enjoying Various Playback Features
Unlike tape operation, playback is simple and
easy in this camera since no time is needed for
rewinding or fast forward operations.
Playlist, playback effects,
and other functions are
also available for
enjoying many different
types of playback.
PLAYLIST CONTENTS
ALL SCENES
01 10.11 2005 11:30
02 15.11 2005 23:00
03 25.11 2005 11:00
Editing Files on your PC
USB 2.0 enables the
smooth transfer of video
and still images to a
computer. With the
bundled image editing
software, you can easily
edit video and create your own DVDs. (Refer to
“Read this first!” and the software installation
and USB connection guide.)
Direct Printing
If your printer is
compatible with
PictBridge, still images
can be printed easily by
connecting the camera
with USB cable directly to the printer. (墌 pg. 47)
Contents
GETTING STARTED 7
Provided Accessories ...................................... 7
Index .............................................................. 10
Power ............................................................. 14
Operation Mode ............................................. 17
Language Setting .......................................... 18
Date/Time Settings ........................................ 18
Brightness Adjustment of the Display ............ 19
Grip Adjustment ............................................. 19
Tripod Mounting ............................................. 19
Inserting/Removing an SD Card .................... 20
Formatting a Recording Medium ................... 20
Selecting a Recording Medium ...................... 21
Remaining Space on the Recording Media ... 21
Drop Detection ............................................... 21
VIDEO RECORDING & PLAYBACK 22
Video Recording ............................................ 22
Zooming ..................................................... 23
Video Playback .............................................. 24
How to Use the Scroll Bar ......................... 25
Date Index Screen ..................................... 25
Various Playback Operations .................... 25
Playback Zoom .......................................... 25
Connecting to a TV, VCR or VDR .................. 26
Playback on a TV ...................................... 26
Dubbing to a VCR (or DVD Recorder) ....... 26
Playback Using the Remote Control .............. 27
STILL IMAGE RECORDING & PLAYBACK 28
Still Image Recording ..................................... 28
Zooming ..................................................... 28
Continuous Shooting ................................. 28
Still Image Playback ...................................... 29
Slide Show ................................................. 29
Index Screen of Still Image Files ............... 29
How to Use the Scroll Bar ......................... 30
Date Index Screen ..................................... 30
Image Rotation .......................................... 30
Playback Zoom .......................................... 30
EN 3
ADVANCED OPERATIONS 31
RECORDING FEATURES .....................................31
Backlight Compensation ................................ 31
Spot Exposure Control ................................... 31
LED Light ....................................................... 31
Manual Settings in MSET Menu .................... 32
How to Select a Menu Item ....................... 32
Manual Exposure ....................................... 32
Manual Focus ............................................33
White Balance ........................................... 34
Shutter Speed ............................................ 35
Program AE ............................................... 36
Effect ......................................................... 36
PLAYBACK FEATURES .......................................37
Wipe or Fader Effects .................................... 37
Playback Effects ............................................ 37
MANAGING FILES ............................................. 38
Viewing File Information ................................ 38
Protecting Files .............................................. 38
Deleting Files ................................................. 39
Cleaning Up a Recording Medium ................. 40
Copying/Moving Still Image Files ................... 41
Resetting the File Number ............................. 42
Creating Play List ........................................... 42
Playing Back Play List ................................... 43
DPOF Print Setting ........................................ 46
Direct Printing with a PictBridge Printer ......... 47
MENU SETTINGS 48
Changing the Menu Settings ......................... 48
Common Menus for All Modes ...................... 48
Video Recording Menus ................................ 50
Video Playback Menus .................................. 50
Still Image Recording Menus ......................... 51
Still Image Playback Menus ........................... 51
REFERENCES 52
Troubleshooting ............................................. 52
Warning Indications ....................................... 55
Cleaning the Camera ..................................... 57
Cautions ......................................................... 57
Specifications ................................................. 60
TERMS ............................................... Back cover
4 EN
Dear Customer,
Thank you for purchasing this hard disk camera.
Before use, please read the safety information
and precautions contained in the pages 4 – 6 to
ensure safe use of this product.
SAFETY PRECAUTIONS
IMPORTANT (for owners in the U.K.)
Connection to the mains supply in the United
Kingdom.
DO NOT cut off the mains plug from this
equipment.
If the plug fitted is not suitable for the power points
in your home or the cable is too short to reach a
power point, then obtain an appropriate safety
approved extension lead or consult your dealer.
BE SURE to replace the fuse only with an
identical approved type, as originally fitted,
and to replace the fuse cover.
If nonetheless the mains plug is cut off be sure to
remove the fuse and dispose of the plug
immediately, to avoid possible shock hazard by
inadvertent connection to the mains supply.
If this product is not supplied fitted with a mains
plug then follow the instructions given below:
DO NOT make any connection to the Larger
Terminal coded E or Green.
The wires in the mains lead are coloured in
accordance with the following code:
Blue to N (Neutral)
or Black
Brown to L (Live)
or Red
If these colours do not correspond with the
terminal identifications of your plug, connect as
follows:
Blue wire to terminal coded N (Neutral) or
coloured black.
Brown wire to terminal coded L (Live) or coloured
Red.
If in doubt — consult a competent electrician.
WARNING: TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS UNIT TO
RAIN OR MOISTURE.
CAUTIONS:
● To prevent shock, do not open the cabinet. No
user serviceable parts inside. Refer servicing
to qualified personnel.
● When you are not using the AC adapter for a
long period of time, it is recommended that you
disconnect the power cord from AC outlet.
CAUTION:
To avoid electric
shock or damage
to the unit, first
firmly insert the
small end of the
power cord into
the AC Adapter
until it is no
longer wobbly,
and then plug the larger end of the power cord
into an AC outlet.
CAUTIONS:
● This camera is designed to be used with PALtype colour television signals. It cannot be used
for playback with a television of a different
standard. However, live recording and LCD
monitor playback are possible anywhere.
● Use the JVC BN-VF707U battery pack and, to
recharge it or to supply power to the camera
from an AC outlet, use the provided multivoltage AC adapter. (An appropriate
conversion adapter may be necessary to
accommodate different designs of AC outlets in
different countries.)
NOTES:
● The rating plate and safety caution are on the
bottom and/or the back of the main unit.
● The serial number plate is on the battery pack
mount.
● The rating information and safety caution of the
AC adapter are on its upper and lower sides.
Do not point the lens directly into the sun. This
can cause eye injuries, as well as lead to the
malfunctioning of internal circuitry. There is also a
risk of fire or electric shock.
CAUTION!
The following notes concern possible physical
damage to the camera and to the user.
Carrying or holding the camera by the LCD
monitor can result in dropping the unit, or in a
malfunction.
Do not use a tripod on unsteady or unlevel
surfaces. It could tip over, causing serious
damage to the camera.
CAUTION!
Connecting cables (Audio/Video, S-Video, etc.) to
the camera and leaving it on top of the TV is not
recommended, as tripping on the cables will
cause the camera to fall, resulting in damage.
EN 5
Information for Users on Disposal of
Old Equipment
[European Union]
This symbol indicates
that the electrical and
electronic equipment
should not be disposed
as general household
waste at its end-of-life.
Instead, the product
should be handed over to
the applicable collection
point for the recycling of
electrical and electronic
equipment for proper
treatment, recovery and
recycling in accordance with your national
legislation.
By disposing of this product correctly, you will
help to conserve natural resources and will help
prevent potential negative effects on the
environment and human health which could
otherwise be caused by inappropriate waste
handling of this product. For more information
about collection point and recycling of this
product, please contact your local municipal
office, your household waste disposal service or
the shop where you purchased the product.
Penalties may be applicable for incorrect disposal
of this waste, in accordance with national
legislation.
(Business users)
If you wish to dispose of this product, please visit
our web page www.jvc-europe.com
information about the take-back of the product.
[Other Countries outside the European Union]
If you wish to dispose of this product, please do
so in accordance with applicable national
legislation or other rules in your country for the
treatment of old electrical and electronic
equipment.
Attention:
This symbol is only
valid in the European
Union.
to obtain
When the equipment is installed in a cabinet or
on a shelf, make sure that it has sufficient space
on all sides to allow for ventilation (10 cm or more
on both sides, on top and at the rear).
Do not block the ventilation holes.
(If the ventilation holes are blocked by a
newspaper, or cloth etc. the heat may not be able
to get out.)
No naked flame sources, such as lighted candles,
should be placed on the apparatus.
When discarding batteries, environmental
problems must be considered and the local rules
or laws governing the disposal of these batteries
must be followed strictly.
The apparatus shall not be exposed to dripping or
splashing.
Do not use this equipment in a bathroom or
places with water.
Also do not place any containers filled with water
or liquids (such as cosmetics or medicines, flower
vases, potted plants, cups etc.) on top of this unit.
(If water or liquid is allowed to enter this
equipment, fire or electric shock may be caused.)
SOME DO’S AND DON’TS ON THE SAFE USE
OF EQUIPMENT
This equipment has been designed and
manufactured to meet international safety
standards but, like any electrical equipment,
care must be taken if you are to obtain the best
results and safety is to be assured.
DO read the operating instructions before you
attempt to use the equipment.
DO ensure that all electrical connections (including
the mains plug, extension leads and
interconnections between pieces of equipment) are
properly made and in accordance with the
manufacturer’s instructions. Switch off and withdraw
the mains plug when making or changing
connections.
DO consult your dealer if you are ever in doubt
about the installation, operation or safety of your
equipment.
DO be careful with glass panels or doors on
equipment.
DON’T continue to operate the equipment if you are
in any doubt about it working normally, or if it is
damaged in any way — switch off, withdraw the
mains plug and consult your dealer.
DON’T remove any fixed cover as this may expose
dangerous voltages.
CONTINUED ON NEXT PAGE
6 EN
DON’T leave equipment switched on when it is
unattended unless it is specifically stated that it is
designed for unattended operation or has a standby
mode. Switch off using the switch on the equipment
and make sure that your family knows how to do
this. Special arrangements may need to be made
for infirm or handicapped people.
DON’T use equipment such as personal stereos or
radios so that you are distracted from the
requirements of road safety. It is illegal to watch
television whilst driving.
DON’T listen to headphones at high volume, as
such use can permanently damage your hearing.
DON’T obstruct the ventilation of the equipment, for
example with curtains or soft furnishings.
Overheating will cause damage and shorten the life
of the equipment.
DON’T use makeshift stands and NEVER fix legs
with wood screws — to ensure complete safety
always fit the manufacturer’s approved stand or legs
with the fixings provided according to the
instructions.
DON’T allow electrical equipment to be exposed to
rain or moisture.
ABOVE ALL
● NEVER let anyone especially children push
anything into holes, slots or any other opening in
the case — this could result in a fatal electrical
shock;
● NEVER guess or take chances with electrical
equipment of any kind — it is better to be safe
than sorry!
Before Using this Camera
This camera records video in MPEG2 format
compliant with SD-VIDEO format.
Remember that this camera is not compatible
with other digital video formats.
Remember that this camera is intended for
private consumer use only.
Any commercial use without proper permission is
prohibited. (Even if you record an event such as a
show, performance or exhibition for personal
enjoyment, it is strongly recommended that you
obtain permission beforehand.)
Do not strike or shake the hard disk.
Before recording important video, be sure to
make a trial recording.
Play back your trial recording to make sure the
video and audio have been recorded properly.
Make a backup of important recorded data
Protect your important recorded data by copying the
files to PC. It is recommended to copy it from your
PC to a DVD or other recording media for storage.
Refer to the software installation and USB
connection guide.
Important notes when requesting repair or
inspection
When the camera is repaired or inspected, data
may be erased, and the hard disk may be formatted.
Back up all data before requesting repair or
inspection.
If a problem occurs with the SD Memory Card,
bring the card together with the camera.
When requesting repairs for breakdowns by your
dealer or JVC service centre, be sure to bring your
camera together with the SD Memory Card. If one
of them is not included, the cause cannot be
diagnosed, and the repair cannot be made properly.
Important notes for destroying and disposing of
camera
When formatting or erasing data using the camera
or PC functions, only the file administration
information is changed. The data is not completely
erased from the hard disk. If you want to completely
erase all of the data, we recommend either using
commercially available software that is specially
designed for that purpose, or by physically
destroying the camera with a hammer etc.
Also read “Cautions” on pages 57 to 59.
● Manufactured under license from Dolby
Laboratories. “Dolby” and double-D symbol are
trademarks of Dolby Laboratories.
●
MascotCapsule is registered trademark of HI
CORPORATION in Japan.
Copyright © 2001 HI CORPORATION. All rights
reserved.
● Other product and company names included in
this instruction manual are trademarks and/or
registered trademarks of their respective holders.
Provided Accessories
OR
GETTING STARTED
EN 7
a AC Adapter AP-V14E or AP-V17E
b Power Cord (AP-V14E only)
c Battery Pack BN-VF707U
d Audio/Video Cable
e USB Cable (Refer to the software installation
and USB connection guide.)
f Shoulder Strap (See page 8 for attachment)
g Lens Cap (See page 8 for attachment)
h CD-ROM
i Remote Control Unit RM-V730UE
j Lithium Battery CR 2025* (for remote control
unit)
k Core Filter for Cables (See page 9 for
attachment)
Large-A (x 1): Audio/Video Cable
Large-B (x 2): USB/S-Video Cable
Small (x 1): DC Cord
* A lithium battery is pre-installed in the remote
control unit at time of shipment (with insulation
sheet). To use the remote control unit, remove the
insulation sheet.
NOTES:
● In order to maintain optimum performance of the
camera, provided cables may be equipped with
one or more core filter. If a cable has only one
core filter, the end that is closest to the filter
should be connected to the camera.
● Make sure to use the provided cables for
connections. Do not use any other cables.
GETTING STARTED
8 EN
GETTING STARTED
Attaching the Shoulder Strap
Follow the illustration.
1 Open the velcro strip.
2 Thread the strap through the eyelet.
3 Fold it back and thread it through the strap
guide and the buckle.
● To adjust the length of the strap, loosen and then
tighten the strap in the buckle.
4 Slide the strap guide fully towards the eyelet.
5 Close the velcro strip.
Attaching the Lens Cap
To protect the lens,
attach the provided lens
cap to the camera as
shown in the illustration.
NOTE:
To confirm the lens cap is
on correctly, make sure the
cap is flush to the camera.
2
Eyelet
3
Strap Guide
1
4
Buckle
5
Place here during
recording.
Attaching the Core Filter
Attach the core filters to the cables. The core
filter reduces interference.
1 Release the stoppers on both ends of the
core filter.
GETTING STARTED
EN 9
LCD Monitor
Pull on the end of the LCD monitor and open
the LCD monitor fully. It can rotate 270°.
Stopper
2 Run the cable through the core filter, leaving
approx. 3 cm of cable between the cable plug
and the core filter.
S-Video/Audio/Video/USB cable
Wind the cable once around the outside of the
core filter as shown in the illustration.
Core Filter (Large)
3 cm
Wind once.
DC cord
Wind the cord twice around the outside of the
core filter as shown in the illustration.
Core Filter (Small)
3 cm
Wind twice.
● Wind the cable so that it is not slack.
3 Close the core filter until it clicks shut.
S-Video/Audio/Video/
USB Cable
DC Cord
GETTING STARTED
NOTES:
● Take care not to damage the cable.
● When connecting a cable, attach the end with the
core filter to the camera.
10 EN
A
Index
GETTING STARTED
TTENTION:
● Be careful not to cover b, c, d, and e during
shooting.
● Be careful not to cover
Y during playback.
Controls
a Mode Switch [MODE] (墌 pg. 17)
b Light Button [LIGHT] (墌 pg. 31)
c Information Button [INFO/ ] (墌 pg. 38)
d Play/Pause Button [49] (墌 pg. 24, 29)
e Forward Search Button [ (
Right Button [ ]/Auto/Manual Mode Switch
[/] (墌 pg. 17)
f Forward Skip Button [ ] (墌 pg. 25)/Down
Button [ ]/Manual Set Button [ SET]
(墌 pg. 32)
g Reverse Search Button [ (
Left Button [ ]
h Menu Button [MENU] (墌 pg. 48)
i Delete Button [ ] (墌 pg. 39)
j Reverse Skip Button [ ] (墌 pg. 25)/Up
Button [ ]/Backlight Compensation Button
[] (墌 pg. 31)/Spot Exposure Control
Button (墌 pg. 31)
k Power Switch [OFF, , ] (墌 pg. 17)
l Lock Button (墌 pg. 17)
m LCD Lock Button
n Zoom Lever [T/W] (墌 pg. 23)
Speaker Volume Control (墌 pg. 24)
o Recording Start/Stop Button (墌 pg. 22, 28)
p Battery Release Button [BATT.] (墌 pg. 14)
5
)] (墌 pg. 25)/
3
)] (墌 pg. 25)/
Connectors
The connectors are located beneath the covers.
Q S-Video Output Connector [S] (墌 pg. 26)
R Audio/Video Output Connector [AV]
S USB (Universal Serial Bus) Connector (Refer
to the software installation and USB
connection guide.)
T DC Input Connector [DC] (墌 pg. 14)
GETTING STARTED
EN 11
Indicators
U Power/Charge Lamp [POWER/CHARGE]
(墌 pg. 14, 17)
V Access Lamp [ACCESS] (Lights up or blinks
when you access to any files. Do not turn off
the power or remove the battery pack/AC
adapter while accessing to files during
recording or playback.)
Other Parts
W Reset Hole [RESET] (墌 pg. 52)
X LCD Monitor
Y Speaker (墌 pg. 24)
a Battery Pack Mount (墌 pg. 14)
b Remote Sensor (墌 pg. 27)
Camera Sensor
c Lens
d LED Light (墌 pg. 31)
e Stereo Microphone
f Shoulder Strap Eyelet (墌 pg. 8)
g Grip Strap (墌 pg. 19)
h SD Card Cover (墌 pg. 20)
i Stud Hole (墌 pg. 19)
j Tripod Mounting Socket (墌 pg. 19)
GETTING STARTED
12 EN
GETTING STARTED
Indications on LCD Monitor
During both Video and Still Image Recording
11:30
10.11. 2005
a Manual Mode Indicator (墌 pg. 17)
: Auto Mode
: Manual Mode
b Tele Macro Mode Indicator (墌 pg. 50)
c Approximate Zoom Ratio (墌 pg. 23, 50)
d Zoom Indicator (墌 pg. 23, 50)
e Iris Lock Indicator (墌 pg. 31, 32)
f White Balance Indicator (墌 pg. 34)
g Brightness Control Indicator (墌 pg. 19, 49)
h Battery Indicator (墌 pg. 55)
i Date/Time (墌 pg. 49)
j Selected Medium Indicator (墌 pg. 21, 49)
k Drop Detection Indicator (墌 pg. 21)
l Manual Focus Adjustment Indicator
(墌 pg. 33)
m Effect Mode Indicator (墌 pg. 36)
n Program AE Mode Indicator (墌 pg. 36)
o Shutter Speed (墌 pg. 35)
: Nightscope Indicator
p Light Indicator (墌 pg. 31)
q ±: Exposure Adjustment Indicator (墌 pg. 32)
: Backlight Compensation Indicator
(墌 pg. 31)
: Spot Exposure Control Indicator
(墌 pg. 31)
During Video Recording only
[0h56m]
a Mode Indicator (墌 pg. 17)
b Wide Mode Indicator (墌 pg. 50)
c Wind Cut Indicator (墌 pg. 50)
d Picture Quality: [U] (ultra fine), [F] (fine), [N]
(normal), [E] (economy) (墌 pg. 50)
e Remaining Time (墌 pg. 22, 62)
f Counter (墌 pg. 49)
g 7REC: (Appears during recording.)
(墌 pg. 22)
79: (Appears during record-standby mode.)
(墌 pg. 22)
h Digital Image Stabiliser (DIS) Indicator
(墌 pg. 50)
During Still Image Recording only
FINE
PHOTO
a Mode Indicator (墌 pg. 17)
b Focus Icon (墌 pg. 28)
c Image Size: 1152 (1152 x 864)*, 1024 (1024 x
768)*, 640 (640 x 480) (墌 pg. 51)
* Not available for GZ-MG30E/EK/GZ-MG20E/EK.
d Picture Quality: FINE (fine) or STD (standard)
(墌 pg. 51)
e Remaining Number of Shots (墌 pg. 63)
f : Continuous Shooting Mode Indicator
(墌 pg. 28)
g Shooting Icon (墌 pg. 28)
h Self-Timer Recording Indicator (墌 pg. 51)
During Video Playback
10. 11. 2005
a Mode Indicator (墌 pg. 17)
b Play List Playback Indicator (Appears when
play list is played back. 墌 pg. 43)
c Picture Quality: [U] (ultra fine), [F] (fine), [N]
(normal), [E] (economy) (墌 pg. 50)
d Playback Mode (墌 pg. 24)
U : Playback
9 : Pause
5
: Forward High-Speed Search
3
: Reverse High-Speed Search
9U : Forward Slow-Motion
Y9 : Reverse Slow-Motion
(The number on the left shows speed.)
e Counter (墌 pg. 49)
f Volume Level Indicator
g Battery Indicator (墌 pg. 55)
h Date (墌 pg. 49)
i Selected Medium Indicator (墌 pg. 21, 49)
j Effect Mode Indicator (墌 pg. 36)
k Wipe/Fader Effect Indicator (墌 pg. 37, 50)
GETTING STARTED
EN 13
During Still Image Playback
11:30
10. 11. 2005
a Mode Indicator (墌 pg. 17)
b Folder/File Number
c Slide Show Playback Indicator (墌 pg. 29)
d Battery Indicator (墌 pg. 55)
e Date/Time (墌 pg. 49)
f Selected Medium Indicator (墌 pg. 21, 49)
NOTE:
When the mode indicators disappear or blink, the
functions of those modes are not available. Such a
phenomenon also occurs when the LCD monitor is
turned 180°. (墌 pg. 9)
GETTING STARTED
14 EN
GETTING STARTED
Power
This camera’s 2-way power supply system lets
you choose the most appropriate source of
power. Do not use provided power supply units
with other equipment.
Charging the Battery Pack
Power/Charge Lamp
Power Switch
Lock Button
To DC connector
Open the cover.
To AC outlet
AC Adapter
BATT.
Battery Pack
(ex. AP-V17E)
1 Set the power switch to OFF.
2 With the arrow on the battery pack pointing
downward, push the battery pack slightly against
the battery pack mount.
● If the battery mount cover is attached, remove it
by sliding BATT.
3 Slide down the battery pack until it locks in
place.
4 Connect the AC adapter to the camera.
5 Connect the power cord to the AC adapter.
(AP-V14E only)
6 Plug the power cord into an AC outlet. The
power/charge lamp on the camera blinks to
indicate charging has started.
7 When the power/charge lamp goes out,
charging is finished. Unplug the power cord from
the AC outlet. Disconnect the AC adapter from
the camera.
To detach the battery pack
While sliding BATT., remove the battery pack.
Required charging time
Battery pack Charging time
BN-VF707U* Approx. 1 hr. 30 min.
BN-VF714U Approx. 2 hr. 40 min.
BN-VF733U Approx. 5 hr. 40 min.
* Provided
Arrow
Battery Pack Mount
NOTES:
A
● This product includes patented and other
proprietary technology and will operate only
with JVC Data Battery. Use the JVC BNVF707U/VF714U/VF733U battery packs. Using
generic non-JVC batteries can cause damage
to the internal charging circuitry.
● If the protective cap is attached to the battery
pack, remove it first.
● During charging, the camera cannot be operated.
● Charging is not possible if the wrong type of
battery is used.
● Make sure to use the battery pack with the arrow
( ) mark. The camera does not turn on with the
battery mount cover without the arrow ( ) mark.
● When charging the battery pack for the first time
or after a long storage period, the power/charge
lamp may not light. In this case, remove the
battery pack from the camera, then try charging
again.
● If the battery operation time remains extremely
short even after having been fully charged, the
battery is worn out and needs to be replaced.
Please purchase a new one.
● Since the AC adapter processes electricity
internally, it becomes warm during use. Be sure to
use it only in well-ventilated areas.
● Using the optional AA-VF7 battery charger, you
can charge the BN-VF707U/VF714U/VF733U
battery pack without the camera.
● After 5 minutes has elapsed in record-standby
mode, the camera will automatically turn off its
power supplied from the AC adapter. In this case,
the battery charge starts if the battery is attached
to the camera.
GETTING STARTED
EN 15
Using the Battery Pack
Perform steps 2 – 3 in “Charging the Battery
Pack”.
Maximum continuous recording time
Battery pack Recording time
BN-VF707U* Approx. 1 hr. 00 min.
BN-VF714U Approx. 2 hr. 10 min.
BN-VF733U Approx. 5 hr. 00 min.
* Provided
( ): When the LED light is on.
NOTES:
● Recording time is reduced significantly under the
following conditions:
• Zoom or record-standby mode is engaged
repeatedly.
• Playback mode is engaged repeatedly.
● Before extended use, it is recommended that you
prepare enough battery packs to cover 3 times the
planned recording time.
TTENTION:
● Before detaching the power source, make sure
that the camera’s power is turned off. Failure to do
so can result in a camera malfunction.
● If the camera is a subject to electrostatic
discharge, turn the power off before using it again.
(55 min.)
(2 hr. 00 min.)
(4 hr. 45 min.)
GETTING STARTED
16 EN
GETTING STARTED
Data Battery System
You can check the remaining battery power and
the recordable time.
1 Make sure the battery is attached.
2 Open the LCD monitor fully.
3 Press INFO/ repeatedly, and the battery
status screen appears.
● It is displayed for approx. 3 seconds if the
button is pressed and released quickly, and for
approx. 15 seconds if the button is pressed
and held for several seconds.
● If “COMMUNICATING ERROR” appears
instead of the battery status even though you
tried to press INFO/ several times, there
may be a problem with your battery. In such a
case, consult your nearest JVC dealer.
● The recordable time display should only be
used as a guide. It is displayed in 10 minute
units.
Using AC Power
Perform step 4 in “Charging the Battery Pack”.
NOTE:
The provided AC adapter features automatic voltage
selection in the AC range from 110 V to 240 V.
About Batteries
DANGER! Do not attempt to take the batteries
apart, or expose them to flame or excessive
heat, as it may cause a fire or explosion.
WARNING! Do not allow the battery or its
terminals to come in contact with metals, as this
can result in a short circuit and possibly start a
fire.
To resume the original function of the
accurate battery power indication
If the battery power indication differs from the
actual operating time, fully charge the battery,
and then run it down. However this function may
not turn back if the battery was used for a long
period of time under extremely high/low
temperature condition or charged too many
times.
Operation Mode
To turn on the camera, set the power switch to
or while pressing down the lock button
located on the switch.
● The power/charge lamp turns on.
To turn off the camera, set the power switch to
OFF.
1
Power Switch
Power/Charge Lamp
2
MODE
LCD Monitor
Set the appropriate operation mode according to
your preference using the power and MODE
switches and ( / ) button.
3
1 Power Switch Position
Set the power switch for recording ( ) or
playback ( ) while pressing down the lock
button.
Power Switch
Power Off
Playback
Recording
Lock Button
GETTING STARTED
EN 17
2 Recording/Playback Mode
Select the recording/playback mode using the
MODE switch.
: Video mode (墌 pg. 22, 24)
: Still image mode (墌 pg. 28, 29)
3 Auto/Manual Mode
Press and hold ( / ) to switch the auto/
manual recording mode. When manual mode is
selected, the indicator appears on the LCD
monitor.
Auto mode:
You can record using no special
effects or manual adjustments.
Manual mode:
Manual recording is possible by
setting various functions.
(墌 pg. 31 – 37)
To return to the auto recording mode
Press ( / ) again so that the indicator
appears.
4 Power-Linked Operation
When the power switch is set to , you can
also turn on/off the camera by opening/closing
the LCD monitor.
GETTING STARTED
18 EN
GETTING STARTED
Language Setting
The language on the display can be changed.
(墌 pg. 48, 49)
1 Set the power switch to or .
2 Press MENU. The menu screen appears.
3 Press / to
select [DISPLAY], then
press 49.
4 Press / to
select [LANGUAGE],
then press 49.
5 Press / to
select the desired
language, then press
49.
6 Press MENU to return to the normal screen.
CAMERA SETTING
BASIC SETTING
REC MEDIA SETTING
DISPLAY
QUALITY
WIDE MODE
WIND CUT
DATE/TIME
SCENE COUNTER
LANGUAGE
CLOCK ADJUST
BRIGHT
Date/Time Settings
The recording start date/time is recorded on the
video/still image file and it can be checked by
pressing INFO during playback. (墌 pg. 24, 29)
In addition, you can find the desired file by the
date index screen. (墌 pg. 30)
1 Set the power switch to or .
2 Press MENU. The menu screen appears.
3 Press / to
select [DISPLAY], then
press 49.
4 Press / to
select [CLOCK
ADJUST], then press
49. The day is
highlighted.
5 Press / to input
the day, then press 49.
Repeat to input the
month, year, hour and
minute.
6 Press MENU to
return to the normal screen.
Built-in Clock’s Rechargeable Lithium
Battery
If the camera is not used for approx. 3 months,
the clock’s lithium battery will become
discharged and the date/time stored in memory
will be lost. When this occurs, first connect the
camera to an AC outlet using the AC adapter for
over 24 hours to charge the clock’s rechargeable
lithium battery. Then perform the date/time
setting before using the camera.
Note that the camera can be used without
setting the date/time.
CAMERA SETTING
BASIC SETTING
REC MEDIA SETTING
DISPLAY
QUALITY
WIDE MODE
WIND CUT
SCENE COUNTER
LANGUAGE
CLOCK ADJUST
BRIGHT
DATE/TIME
CLOCK ADJUST
DATE TIME
11 0 7:
200531 01
GETTING STARTED
EN 19
Brightness Adjustment of the Display
The brightness of the display can be adjusted.
1 Set the power switch to or while
pressing down the lock button located on the
switch.
2 Open the LCD monitor fully. (墌 pg. 9)
3 Press MENU. The menu screen appears.
4 Press / to select [DISPLAY], then press
49.
5 Press / to select
[BRIGHT], and press 49.
The brightness control
indicator appears.
6 Press / until the appropriate brightness
is reached.
7 Press 49 to clear the brightness control
indicator from the display.
Grip Adjustment
1 Adjust the velcro strip.
2 Pass your right hand
through the loop and grasp
the grip.
3 Adjust your thumb and
fingers through the grip to
easily operate the
recording start/stop button,
power switch and zoom
lever. Be sure to fasten the
velcro strip to your
preference.
Tripod Mounting
To attach the camera to a
tripod, align the direction
stud and screw to the
mounting socket and
stud hole on the camera.
Then tighten the screw
clockwise.
● Some tripods are not
equipped with studs.
GETTING STARTED
20 EN
A
GETTING STARTED
Inserting/Removing an SD Card
You can use an SD card as a recording medium
in the SD slot. See page 62 for the guaranteed
media to work with this camera.
Clipped Edge
SD Slot
SD Card Cover
1 Make sure the camera’s power is off.
2 Open the SD card cover.
3 To insert an SD card, firmly insert it with its
clipped edge first.
To remove an SD card, push it once. After the
SD card comes out of the camera, pull it out.
● Do not touch the terminal on the reverse side of
the label.
4 Close the SD card cover.
To protect valuable files
Slide the write/erase protection tab on the side
of the SD card in the direction of “LOCK”. This
prevents the SD card from being recorded over.
To record on this SD card, slide the tab back to
the position opposite to “LOCK” before inserting
it.
NOTE:
Before using a new SD card, it is necessary to
format the card. (墌 pg. 20)
TTENTION:
Do not insert or remove the SD card while the
camera is turned on, as this may cause the SD card
to be corrupted or cause the camera to become
unable to recognise whether or not the SD card is
installed.
SD Card (optional)
Label
Protection Tab
Write/Erase
Formatting a Recording Medium
You can format (initialise) the built-in hard disk
(HDD) or SD cards. You have to format the
newly-purchased SD cards with this camera
before using them. This enables stable speeds
and operation when accessing the recording
medium. Be aware that all files and data
including protected files will be erased.
(墌 pg. 38)
1 Set the power switch to or .
2 Press MENU. The menu screen appears.
3 Press / to select
[REC MEDIA SETTING],
then press 49.
4 Press / to select
[FORMAT], then press
49.
5 Press / to select
[HDD] or [SD], then
press 49.
6 Press / to select [EXECUTE], then
press 49.
● By pressing the 49 button while selecting [HDD]
and holding down the button in step
erase the data on the hard disk in a format that is
difficult to recover. Moreover, by repeating this
procedure, you can make the data even more
difficult to recover. When formatting in this way, a
formatting progress bar is displayed.
● To cancel the formatting, select [CANCEL], then
press 49.
CAUTION:
Do not remove the SD card or perform any other
operation (such as turning off the power) during
format. Also, be sure to use the provided AC
adapter, as the recording medium may be corrupted
if the battery becomes exhausted during format. If
the recording medium becomes corrupted, format it
again.
NOTE:
Do not format the recording medium on the PC.
Make sure to format the recording medium on the
camera.
DIS
CAMERA SETTING
BASIC SETTING
REC MEDIA SETTING
DISPLAY
QUALITY
WIDE MODE
VIDEO MODE
IMAGE MODE
FORMAT
CLEAN UP
COPY/MOVE
5, you can
Loading...