JVC DT-V1900CG/E, DT-V1900CG/U, DT-V1900CG Instructions Manual

MULTI-FORMAT MONITOR

DT-V1900CG

For Customer Use:

Enter below the Serial No. which is located on the rear of
the cabinet. Retain this information for future reference.

Model No. : DT-V1900CG
Serial No. :

INSTRUCTIONS

UNDER

PULSE

COLOR

DEGAUSS

SCAN

CROSS

MUTING

VOLUME

The illustration above shows the DT-V1900CG with provided
wide mask attached.

OFF

SLOT 1

SLOT 2

A

B

C

ASPECT

MENU

SCREENS

AREA

CHECK

MARKER

INPUT SELECT

D

POWER

SLOT 3

E

F

LCT1117-001B

SAFETY PRECAUTIONS

In order to prevent any fatal accidents caused by
misoperation or mishandling the monitor, be fully aware of all
the following precautions.

W ARNINGS

To prevent fire or shock hazard, do not expose this
monitor to rain or moisture. Dangerous high voltages
are present inside the unit. Do not remove the back
cover of the cabinet. When servicing the monitor,
consult qualified service personnel. Never try to service
it yourself.

W ARNING : THIS APPARATUS

MUST BE EARTHED.

Improper operations, in particular alternation of high
voltage or changing the type of tube may result in x-ray
emission of considerable dose. A unit altered in such a
way no longer meets the standards of certification, and
must therefore no longer be operated.

This monitor is equipped with a 3-blade grounding-type
plug to satisfy FCC rule. If you are unable to insert the
plug into the outlet, contact your electrician.

FCC INFORMATION (U.S.A. only)

CAUTION: Changes or modification not approved by

JVC could void the user's authority to operate the
equipment.

NOTE: This equipment has been tested and found to
comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference when the equipment is operated in a
commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a
residential area is likely to cause harmful interference in
which case the user will be required to correct the
interference at his own expense.

Notice (U.S.A. only)

This product utilizes both a Cathode Ray Tube (CRT) and
other components that contain lead. Disposal of these
materials may be regulated in your community due to
environmental considerations. For disposal or recycling
information please contact your local authorities, or the
Electronics Industries Alliance: <http://

www.eiae.org.>

䡵 PRECAUTIONS

● Use only the power source specified on the unit.

(120 V/230 V AC, 50 Hz/60 Hz)

● Keep flammable material, water, and metal objects away
from the unit – especially the interior of the unit.

● This unit incorporates high voltage circuitry.
For your own safety and that of your equipment, do not
attempt to modify or disassemble this monitor.
There are no user-serviceable parts inside.

● Video or audio signals cannot be input to this monitor
without optional input cards.

● In these instructions, all explanations (except where noted)
refer to the DT-V1900CG with input cards installed.

SCREEN BURN

● It is not recommended to keep a certain still image
displayed on screen for a long time as well as displaying
extremely bright images on screen. This may cause a
burning (sticking) phenomenon on the screen of cathode-ray
tube. This problem does not occur as far as displaying
normal video playback motion images.

䡵 HANDLING

● Avoid shocks or vibrations. These may damage the unit and

cause it to malfunction.

● Do not block the ventilation slots.

● Do not expose this unit to high temperatures.

Extended exposure to direct sunlight or a heater could
deform the cabinet or cause the performance of internal
components to deteriorate.

● Do not place the unit near appliances generating strong
electric or magnetic fields. There can generate picture noise
and instability.

● Keep the monitor clean by wiping the cabinet and CRT
screen with a piece of soft cloth. Do not apply thinner or
benzine. These chemicals can damage the finish and erase
printed letters. When the unit is excessively dirty, use a
diluted neutral cleanser, then wipe away the cleanser with a
dry cloth.

DEGAUSS

● Do not use a magnet eraser to degauss the monitor’s
cathode ray tube from the outside. Doing so may distort its
aperture grill and cause a malfunction.

2

POWER CONNECTION

The power supply voltage rating of this product is AC 120 V (For U.S.A. and Canada only) and AC 230 V (For European countries
or United Kingdom), the power cord attached conforms to the following power supply voltage and countries. Use only the power
cord designated to ensure Safety and EMC regulations of each countries.

Power cord

Power supply voltage : AC 120 V AC 230 V AC 230 V
Countries : U.S.A. and Canada European countries United Kingdom

Warning:

● Do not use the same Power Cord for AC 120 V as for AC 230 V. Doing so may cause malfunction, electric shock

or fire.

Note for the United Kingdom power cord only

The plug on the United Kingdom power cord has a built-in fuse. When replacing the fuse, be sure to use only a correctly rated
approved type, re-fit the fuse cover.
(Consult your dealer or qualified service personnel.)

How to replace the fuse

Open the fuse compartment with the blade screw driver, and
replace the fuse.
(* An example is shown in the illustration.)

Fuse

CONTENTS

SAFETY PRECAUTIONS........................................................................2

CONTROLS AND FEATURES ................................................................4

CONTROLS AND FEATURES

(INPUT CARD: OPTIONAL)..................................................................6

PREPARATION .......................................................................................9

BASIC MENU OPERATIONS

(MAIN MENU, SETUP MENU) ............................................................11

HOW TO USE “MAIN MENU”...............................................................12

HOW TO USE “SETUP MENU”............................................................15

HOW TO USE EXTERNAL CONTROL.................................................20

TROUBLESHOOTING...........................................................................22

SELF-CHECK INDICATIONS ..............................................................24

SPECIFICATIONS .................................................................................25

3

CONTROLS AND FEATURES

FRONT VIEW

<Front Panel>

2 3 4 5 87 11 12 13 14

MUTING

VOLUME

T ally lamp

1

1

UNDER

PULSE

COLOR

SCAN

CROSS

OFF

DEGAUSS

MENU

POWER

SLOT 1

SLOT 2

SLOT 3

A

B

C

E

D

F

ASPECT

SCREENS

AREA

INPUT SELECT

CHECK

MARKER

Lights when the tally control signal is ON. Set the MAKE/
TRIGGER terminal’s tally control in the REMOTE
(external control) terminal setup menu. For details, refer
to Page 20. The lamp color can be set to red or green.
To set the color, use TALLY SELECT in the "FUNCTION
SETTING" setup menu or MAKE/TRIGGER in the
REMOTE (external control) terminal setup menu. For
details, refer to Page 16 and 20.

PHASE adjustment knob

2

Adjusts picture hue. Turn the knob to the left to make the
picture redder, and turn it to the right to make the picture
greener.

CHROMA adjustment knob

3

Adjusts picture color density. Turn the knob to the left to
make the picture color lighter, and turn it to the right to
make the picture color deeper.

BRIGHT adjustment knob

4

Adjusts picture brightness. Turn the knob to the left to
make the picture darker, and turn it to the right to make
the picture brighter.

CONTRAST adjustment knob

5

Adjusts picture contrast. Turn the knob to the left to make
the picture contrast lower, and turn it to the right to make
the picture contrast higher.

VOLUME buttons

6

Adjusts the speaker volume. Pressing this button displays
the VOLUME level bar on the screen. Pressing the
button again allows you to adjust speaker volume.

MUTING button

7

Pressing this button mutes the input sound. "MUTING
ON" is displayed on the screen. Pressing the VOLUME
"–/+" button or the MUTING button restores the sound.
"MUTING OFF" is displayed on the screen. On-screen
indications disappear after three seconds.
NOTE: The MUTING button functions even when nothing

is displayed on screen (such as Main, Setup
Menu, or Volume level bar ). In this case,
"MUTING OFF" will not be displayed when the
VOLUME "–/+" button is pressed. Indications will
be shown even when the STATUS DISPLAY
setting is "OFF."

MUTING

VOLUME

18 19 20 21 22 23 24 25

UNDER

PULSE

DEGAUSS

MENU

SCAN

SCREENS

CHECK

CROSS

ASPECT

COLOR

OFF

AREA

MARKER

SLOT 1

A

B

SLOT 2

C

INPUT SELECT

SLOT 3

D

E

F

1096 15 16 17

EMBEDDED AUDIO channel switch button

8

Pressing this button switches the input sound channel.
When the button is pressed, the channel is advanced.
When the button is pressed, channel is reversed.

!

!

NOTE: The channel indication will display the selected

channel when EMBEDDED in the "FUNCTION
SETTING" setup menu is selected. It is valid
when an input card compliant with EMBEDDED
AUDIO is installed.

Menu select buttons

9

Selects menu screen items or set-up menu screen.

MENU button

10

Displays, adjusts or closes a menu screen.

DEGAUSS button/lamp

11

Press the DEGAUSS button. The button lights and
degaussing is performed automatically. When the
degaussing is completed, the light goes off.

UNDER SCAN button/lamp

12

Press the UNDER SCAN button. The button lights and
the screen is reduced (under-scan) and the whole screen
is displayed. When the UNDER SCAN button is pressed
while lit, the light goes off and the screen returns to
normal size (over-scan). Use this function to check the
whole screen.

NOTE: This function is invalid with the RGB-input screen.

PULSE CROSS button/lamp

13

Press the PULSE CROSS button. The picture is
separated into 4 parts. The synchronized signal displayed
in the shape of a cross separating the parts. The screen
automatically brightens to make it easier to confirm
synchronized sections easy. When the PULSE CROSS
button is pressed while lit, the light goes off and the
normal screen is restored.
NOTE: This function is invalid with the RGB-input screen.

POWER

4

REAR/SIDE VIEW

<Rear Panel>

MAKE

RS-232C

26

SLOT1

SLOT2

SLOT3

MAIN POWER

27

28
29

COLOR OFF button/lamp

14

Press the COLOR OFF button. The button lights and the
screen becomes monochrome. When the COLOR OFF
button is pressed while lit, the light goes off and the
normal screen is restored.
Use this function to confirm the noise in the brightness
signal or to confirm the white balance.

NOTE: This function is invalid with the RGB-input screen.

SCREENS CHECK button/lamp

15

Press the SCREENS CHECK button. The button lights
and the screen changes in the following order:

Normal screen[Red screen[Green screen

[

Press the SCREENS CHECK button when the blue
screen is displayed. The light goes off and the normal
screen is restored.
Use this function to confirm or adjust CHROMA or
PHASE.

NOTE: This function is invalid with the RGB-input screen.

ASPECT button/lamp

16

When the ASPECT button is pressed while the screen
ratio is 4:3, the button lights and the screen ratio changes
to 16:9. When the ASPECT button is pressed while lit, the
light goes off and the normal screen is restored.

NOTE: This function is invalid with the RGB-input screen.

AREA MARKER button/lamp

17

When the AREA MARKER button is pressed while the
screen ratio is 16:9, the button lights and the white
marker is displayed. This shows the screen size (area)
set on the menu. When the AREA MARKER button is
pressed while lit, the light goes off and the normal screen
is restored.

NOTE: This function is invalid with the RGB-input screen.

– INPUT SELECT buttons/lamps

23

18

Press the unlit button. The button lights and the input
signal is changed. (any other lit button goes off.)
When the lit button is pressed, the status of the current
input signal is displayed (for approx. 3 seconds). Buttons
A through F correspond to the signals input via the input
cards installed in SLOT 1 through SLOT 3.
A, B : select the picture from the SLOT 1 input card.
C, D : select the picture from the SLOT 2 input card.
E, F : select the picture from the SLOT 3 input card.

Blue screenp

<Side Panel>

30

Refer to pages 6 and 8 for correspondence between the
input terminals and the INPUT SELECT buttons.

Power lamp

24

Unlit : The main power is OFF.
Orange : The main power is ON, but the monitor’s power

is OFF (in stand-by mode).

Green :The main power is ON, and the monitor’s power

is ON (in normal operation mode).

POWER switch

25

Press the power switch to turn the monitor’s power ON or
OFF when the main power is ON.
NOTE:When RUSH DELAY TIME is set to SLOW in the

set-up menu, it takes approx. 3.2 seconds for the
power to actually turn ON after the power switch is
pressed.

REMOTE (external control) terminals

26

Terminals for controlling the monitor from an external unit.
MAKE/TRIGGER terminal (Upper):
Enables the monitor to be controlled by closing the circuit
(point of contact) connected to the terminal.
RS-232C terminal (Lower):
Enables the monitor to be controlled from a personal
computer via serial communication.

Input card slots (SLOT 1 — SLOT 3)

27

Optional input cards can be installed in these slots. Input
cards are not provided when you purchase the monitor.
NOTE:It is not possible to input video or audio signals to

the monitor when no input cards are installed.

Main power switch

28

Press the switch to turn the main power ON or OFF.
When the main power is ON, the power lamp on the front
panel lights in yellow and the monitor enters the stand-by
mode.
I : ON 䡬 : OFF

29

AC inlet

Power input connector. Connect the provided AC power
cord to an AC outlet (120 V/230 V AC, 50 Hz/60 Hz).
* Attach the provided Power Cord Holder to the AC inlet to

prevent accidental disconnection of the AC power cord.
Refer to page 10 for details.

Built-in speaker (monaural)

30

Outputs the input audio.

5

CONTROLS AND FEATURES

(INPUT CARD: OPTIONAL)

䡵 COMPONENT/RGB INPUT CARD (OPTIONAL:

IF-C01COMG)

Video input/output terminals

1

Input (IN) and output (OUT) terminals for component

G/Y

OUTIN

B/PB/B-Y

1

OUTIN

R/PR/B-Y

OUTIN

HD/C

S

OUTIN

VD

OUTIN

OUTIN

AUDIO

OUT

IN

䡵 Compatible signal formats:

480/60i, 576/50i, 576/50p, 480/60p, 720/60p, 1035/60i,
1080/50i, 1080/60i, 1080/24psF

2

3

4

(color difference) or RGB signals.
The IN and OUT terminals are bridge-connected.
(When no cable is connected to the OUT terminal, the
input signal is automatically terminated.)
Select component signal : press INPUT SELECT A/C/E

Select RGB signal :press INPUT SELECT B/D/F

2

Synchronized signal input/output terminals

Input (IN) and output (OUT) terminals for the vertical,
horizontal or complex synchronized signals.
Function differs depends on the SYNC SELECT setting in
the FUNCTION SETTING setup menu. For details, refer to
Page 16.
The IN and OUT terminals are bridge-connected.
(When no cable is connected to the OUT terminal, the
input signal is automatically terminated.)

Audio input/output terminals

3

Input (IN) and output (OUT) terminals for audio signals.
The IN and OUT terminals are bridge-connected.

Connection terminal (to a Multi-Format Monitor)

4

Attach to the connection terminal of your Multi-Format
Monitor.

button
button

䡵 VIDEO INPUT CARD (OPTIONAL: IF-C01PNG)

1

Video input/output terminals

Input (IN) and output (OUT) terminals for video signals.

VIDEO 1

OUT

IN

VIDEO 2

IN

EXT.SYNC

OUT

Y/C IN

1

2
3

OUT

IN

AUDIO 1

OUT

IN

AUDIO 2

䡵 Compatible signal formats:

NTSC (3.58 MHz), PAL (4.43 MHz), black-and-white
(50 Hz/60 Hz)
* You can select “AUTO” (automatic selection), “NTSC” or

“PAL” in SETUP MENU when switching NTSC or PAL.
Normally select AUTO. However, if the input signal is
unstable, select NTSC or PAL.

4

5

The IN and OUT terminals are bridge-connected.
(When no cable is connected to the OUT terminal, the
input signal is automatically terminated.)
Select VIDEO 1 : press INPUT SELECT A/C/E button
Select VIDEO 2 : press INPUT SELECT B/D/F button

S-video input terminal

2

Input terminal for the S-video signal.
When an S-video signal is input to this terminal and a
video signal is input to VIDEO 2, the S-video signal has
priority over the video signal.
When choosing the S-video input, press INPUT SELECT
B/D/F button.

3

Synchronized signal input/output terminals

Input (IN) and output (OUT) terminals for the complex
synchronized signals.
Function differs depends on the SYNC SELECT setting in
the FUNCTION SETTING setup menu. For details, refer to
Page 16.
The IN and OUT terminals are bridge-connected.
(When no cable is connected to the OUT terminal, the
input signal is automatically terminated.)

Audio input/output terminals

4

Input (IN) and output (OUT) terminals for audio signals
corresponding to VIDEO 1 and VIDEO 2. The IN and
OUT terminals are bridge-connected.

Connection terminal (to a Multi-Format Monitor)

5

Attach to the connection terminal of your Multi-Format
Monitor.

6

䡵 SDI INPUT CARD (OPTIONAL: IF-C01SDG)

Output terminal for a selected component

1

SWITCHED

OUT

1

IN

SDI 1

2

IN

SDI 2

AUDIO 1

OUT

IN

AUDIO 2

䡵 Compatible signal formats: 480/60i, 576/50i, 576/50p

3

4

serial digital signal

Output terminal for a selected digital signal (the input
displayed on the screen). The output signal is cable­compensated.
NOTE: When the monitor’s power is OFF, no digital

signal is output.

Input terminals for component serial digital

2

signals

Input terminals for the digital signal.
Select SDI 1 : press INPUT SELECT A/C/E button
Select SDI 2 : press INPUT SELECT B/D/F button

Audio input/output terminals

3

Input (IN) and output (OUT) terminals for the analog
signals corresponding to SDI 1 and SDI 2.
NOTE: This input card cannot decode audio data even if

contained in the input digital signal.

Connection terminal (to a Multi-Format

4

Monitor)

Attach to the connection terminal of your Multi-Format
Monitor.

䡵 HD SDI INPUT CARD (OPTIONAL: IF-C01HSDG)

Output terminal for a selected component

1

SWITCHED

OUT

1

HD SDI 1

IN

2

IN

HD SDI 2

AUDIO

OUT

IN

䡵 Compatible signal formats: 720/60p, 1035/60i, 1080/50i,

1080/60i, 1080/24psF

3

4

serial digital signal

Output terminal for a selected digital signal (the input
displayed on the screen). The output signal is cable­compensated.
NOTE: When the monitor’s power is OFF, no digital

signal is output.

Input terminals for component serial digital

2

signals

Input terminals for the digital signal.
Select HD SDI 1 : press INPUT SELECT A/C/E button
Select HD SDI 2 :press INPUT SELECT B/D/F button

Audio input/output terminals

3

Input (IN) and output (OUT) terminals for the analogue
audio signals.
NOTE: This input card cannot decode audio data even if

contained in the input digital signal.

Connection terminal (to a Multi-Format

4

Monitor)

Attach to the connection terminal of your Multi-Format
Monitor.

7

CONTROLS AND FEATURES

(INPUT CARD: OPTIONAL) (cont'd)

䡵 HD SDI INPUT CARD (OPTIONAL: IF-C12HSDG)

Input and output terminals for HD SDI 1

1

component serial digital signals

Input (IN) and output (OUT) terminals for HD serial digital
signals.
Select HD SDI 1: press INPUT SELECT A/C/E button

Input and output terminals for HD SDI 2

2

component serial digital signals

Input (IN) and output (OUT) terminals for HD serial digital
signals.
Select HD SDI 2: press INPUT SELECT B/D/F button

3

Connection terminal (to a Multi-Format
Monitor)

Attach to the connection terminal of your Multi-Format
Monitor.

OUT

OUT

E.AUDIO
HD SDI 1

IN

1

E.AUDIO
HD SDI 2

IN

3

2

䡵 Compatible signal formats: 720/60p, 1080/50i, 1080/60i,

1035/60i, 1080/24psF, EMBEDDED AUDIO

8

PREPARATION

䡵 INSTALLING THE INPUT

CARD

Optional input cards are necessary to use the functions of this
monitor. Before mounting the monitor or connecting other
equipment to the monitor, be sure to install the input cards.

1. Turn off the Multi-Format Monitor’s main
power and unplug the power cable from
the AC outlet.

2. Unscrew the screws and remove the slot
cover from the slot (on the rear side of the
monitor) in which you are going to install
the card.

Slot cover

Rear side of the DT-V1900CG
Multi-Format Monitor

3. Insert the Input Card’s board (green­colored) into the slot, fitting the board into
the guide rails on the top and bottom of
the slot.

Fit the board to
the guide rails.

䡵 ATT ACHING THE WIDE

MASK

A wide mask is provided with the monitor. This changes the
viewable screen area to the 16:9 aspect ratio.
The wide mask cannot be attached to the monitor after the
monitor is mounted in a rack. Mount the wide mask before
installing the monitor in a rack.

1. Prepare the provided wide mask and 4
screws (for attaching).

2. Attach the wide mask to the monitor.

3. Secure the wide mask with the screws (fix
2 screws each to both right and left side).

Knob

Guide rails

Input card (the illustration shown
is of the IF-C01PNG)

Knob

4. Push the Input Card in so that its front
panel touches the monitor’s rear panel.

5. Secure the Input Card by replacing the
screws removed in Procedure 2.

NOTE :Do not touch the terminal connected to the monitor or

board pattern.
Do not remove slot covers from the monitor’s slots if
they are not in use.

● When detaching the wide mask, follow this procedure in
reverse.

9

PREPARATION (cont'd)

䡵 ATT ACHING THE POWER CORD HOLDER

The provided Power Cord Holder prevents accidental disconnection of the AC power cord from the AC inlet.
The Power Cord Holder consists of two parts; a case and cover.

1. Attach the Power Cord Holder case to the AC inlet on the back of the monitor with 2 screws
(provided).

2 Attach the Power Cord Holder cover to the AC power cord.

Press the cover until it clicks.

3. Connect the AC power cord to the AC inlet, and join the Power Cord Holder cover with the
case.

Hold until it clicks.

Caution:

A different plug shape will result in the case being attached to a different position. Check to make sure the plug doesn't
pull out after the case is attached.

10

BASIC MENU OPERATIONS

<MAIN MENU>

APERTURE CONTROL
SLOT CONDITION
sub menu POSITION :LOWER
AREA MARKER :OFF
AREA MARKER-R :OFF
CENTER MARKER :OFF
COLOR MATRIX

EXIT:

MENU

ENTER:+ SELECT:

<APERTURE CONTROL>

LEVEL :00
CONTROL FREQ. :HIGH
sub menu
reset

EXIT:

MENU

ENTER:+ SELECT:

MENU

(MAIN MENU, SETUP MENU)

䡵 ABOUT MENU SCREENS

This monitor features a MAIN MENU (main menu screen) and
a SETUP MENU (setup menu screen).
The MAIN MENU contains the functions normally used, and
the SETUP MENU contains the settings required for initial
setup.

<MAIN MENU>

APERTURE CONTROL
SLOT CONDITION
sub menu POSITION :LOWER
AREA MARKER :OFF
AREA MARKER-R :OFF
CENTER MARKER :OFF
COLOR MATRIX

EXIT:

MENU

ENTER:+ SELECT:

MAIN MENU (main menu screen)

NOTE :The contents of menus vary depending on the input

signal or combination of the monitor’s settings.

<MAIN MENU>

APERTURE CONTROL
SLOT CONDITION
sub menu POSITION :LOWER
COLOR MATRIX

MENU

ENTER:+ SELECT:

EXIT:

MAIN MENU when the 4:3 video
signal is input

<SETUP MENU>

FUNCTION SETTING
PICTURE SUB ADJ.
COLOR TEMP/BAL.
SIZE/POSI.ADJ.
DISTORTION ADJ.
STATUS DISPLAY
CONTROL LOCK :ON
all reset

EXIT:

MENU

ENTER:+ SELECT:

SETUP MENU

(setup menu screen)

<MAIN MENU>

SLOT CONDITION
sub menu POSITION :LOWER

MENU

ENTER:+ SELECT:

EXIT:

MAIN MENU when the RGB signal
is input

䡵 BASIC MENU OPERATION

● To select an item,

Press the

or buttons to move the cursor (4) on the

Menu Screens and select the desired item.

● To set (select) or adjust an item,

Press the

or buttons to select or adjust the desired

item.

● When the desired item has other menus (hierarchical
menus),

Press the

button to display the lower hierarchical menu.

● To return to the former Menu Screen,

Press the

Press the
select or adjust the item.

Cursor
Move (select) with the or buttons.

button.

MENU

or buttons to

Menu in an item

䡵 HOW TO USE THE SUB

䡵 DISPLAYING THE MENU

● To display MAIN MENU

●To display SETUP MENU

䡵 CLOSING THE MENU

● Using the MENU button

● With no operation

NOTE :When you perform the “reset” or “all reset” function,

SCREENS

Press the

Press the button while pressing the button on the
front panel.

button on the front panel.

MENU

UNDER

PULSE

COLOR

SCAN

CROSS

OFF

DEGAUSS

MUTING

ASPECT

MENU

SCREENS

AREA

VOLUME

CHECK

MARKER

POWER

SLOT 1

SLOT 2

SLOT 3

A

C

B

D

E

F

INPUT SELECT

MUTING

VOLUME

DEGAUSS

MENU

SCREENS

Press the
disappears.

When approx. 30 seconds have passed since the last Menu
operation, both screens will disappear.
* Some items on the Menu Screens disappear automatically

after setting.

button a few times until the Menu Screen

MENU

the Menu Screen does not disappear unless you
press the MENU button.

MENU

The sub menu function applies to Menu Screen items that
should be adjusted or set while watching the picture. This
function simplifies the adjustment or setting while watching
the picture by displaying the single item on the top or bottom
of the screen.

● To use the sub menu function,

Press the
press the

● To adjust or set an item in the sub menu screen,

Press the

● To change the item to be adjusted or set,

Press the

● To change the position of the sub menu screen,

Set “UPPER” (on the top) or “LOWER” (on the bottom) in
“sub menu POSITION” of MAIN MENU.

● To close the sub menu screen,

Press the
displayed.

<PICTURE SUB ADJ.>

CONTRAST : 00
BRIGHT : 00
CHROMA : 00
PHASE : 00
NTSC SETUP : 00
COMPO.LEVEL :SMPTE
sub menu
reset

EXIT:

or buttons to select “ sub menu”. Then,

button to display the sub menu screen.

or buttons.

or buttons.

button. The previous Menu Screen is

MENU

Example of sub menu screen

CONTRAST : 00

- - + +

MENU

ENTER:+ SELECT:

CONTRAST : 00

- - + +

The upper pale screen; when setting
“UPPER” in “sub menu POSITION”
The lower dark screen; when setting
“LOWER” in “sub menu POSITION”

11

HOW TO USE “MAIN MENU”

䡵 “MAIN MENU” ITEMS

The following items appear in MAIN MENU.

Items

1 APERTURE CONTROL Compensates the frequency characteristics of the input video signal. *1
2 SLOT CONDITION Displays the status of the input cards installed in each of the input card slots.
3 sub menu POSITION Selects the display position of the sub menu superimposed on the screen.
4 AREA MARKER Selects the size marker for the other screen ratio used when the screen

5 AREA MARKER-R Selects the size marker for the other screen ratio used when the screen ratio is

6 CENTER MARKER Makes the center marker appear or disappear. *2
7 COLOR MATRIX Selects or adjusts the picture color matrix. *1

Functions Displays

ratio is 16:9.

16:9. (for external control)

*2

*2

About “Displays” *1: Not displayed when an RGB signal is input.

*2: Displayed only when the screen ratio is 16:9. Not displayed when an RGB signal is input.

When some items are not displayed depending on the input signals, subsequent items will move up.

䡵 “MAIN MENU” SCREENS

<MAIN MENU>

APERTURE CONTROL
SLOT CONDITION
sub menu POSITION :LOWER
AREA MARKER :OFF
AREA MARKER-R :OFF
CENTER MARKER :OFF
COLOR MATRIX

MENU

ENTER:+ SELECT:

EXIT:

<APERTURE CONTROL>

LEVEL : 00
CONTROL FREQ. :HIGH
sub menu
reset

MENU

ADJUST:- + SELECT:

EXIT:

<SLOT CONDITION>

INPUT A : VIDEO-1
INPUT B : VIDEO-2
INPUT C : COMPO.
INPUT D : RGB
INPUT E : NO SLOT
INPUT F : NO SLOT

MENU

EXIT:

<COLOR MATRIX>

SELECT :ITU601

MENU

ADJUST:- + SELECT:

EXIT:

LEVEL :+05

- - + +

The menu screen when “sub
menu” is selected.

<COLOR MATRIX>

SELECT :MANUAL
R-Y PHASE : 90
R/B GAIN :0.86
G-Y PHASE : 244
G/B GAIN :0.36
sub menu
reset

MENU

ADJUST:- + SELECT:

EXIT:

LEVEL :+05

- - + +

The sub menu screen when
“sub menu POSITION” is set
to “UPPER”.

R-Y PHASE :+90

- - + +

<MAIN MENU>

APERTURE CONTROL
SLOT CONDITION
sub menu POSITION :LOWER
COLOR MATRIX

MENU

ENTER:+ SELECT:

EXIT:

The menu screen when the
screen ratio is 4:3

<MAIN MENU>

SLOT CONDITION
sub menu POSITION :LOWER

EXIT:

The menu screen when an
RGB signal is input

12

MENU

ENTER:+ SELECT:

The menu screen when
“MANUAL” is selected.

The menu screen when “sub
menu” is selected.

䡵 ITEM CONTENTS AND ADJUSTMENT RANGE/SETTINGS

16:9

4:3

14:9 13:9

1. APERTURE CONTROL

Compensates the frequency
characteristics of the input
video signal. Press the
button to display the setting
menu illustrated on the right.
NOTE :APERTURE

CONTROL is not
displayed when the
RGB signal is input.

Item :LEVEL
Adjustment
range :00 ~ +10
Function :Adjusts the compensate value. The higher the

number is, the larger the compensate value gets.

Item :CONTROL FREQ.
Settings : HIGH/LOW/OFF
Function :Adjusts the frequency compensation.

HIGH:Compensates the high frequencies.
LOW :Compensates the low frequencies.
OFF :Deactivates the aperture compensation.

Item :sub menu
Adjustment range/
Settings : Same as LEVEL or CONTROL FREQ.
Function :Performs the LEVEL or CONTROL FREQ.

settings in a single-line display. The display
position depends on the “sub menu POSITION”
setting.

<APERTURE CONTROL>

LEVEL : 00
CONTROL FREQ. :HIGH
sub menu
reset

EXIT: MENU ADJUST:- + SELECT:

3. sub menu POSITION

Items :Selects the display position of the sub menu

superimposed on the screen.
Settings :UPPER/LOWER
Functions : UPPER :An adjustment item is displayed on the

top of the screen.

LOWER :An adjustment item is displayed on the

bottom of the screen.

4. AREA MARKER

Items :Selects the size marker for the other screen ratio

(aspect) used when the screen ratio is 16:9.
Settings :OFF/16:9/4:3/13:9/14:9/MODE 1/MODE 2
Functions : OFF: The marker is not displayed.

16:9/4:3/13:9/14:9: Displays the marker (a white

quadrangle) showing the screen size of each

aspect ratio.

MODE 1/MODE 2: Displays no markers because

these settings will be used for function expansion

in the future.

● AREA MARKER is displayed when a 16:9 picture such as

1080i/1035i/720p etc. is displayed or the picture is
switched to the 16:9 screen ratio by pressing the ASPECT
button.

● To actually display the marker, the AREA MARKER

button on the monitor needs to be pressed so that it is
illuminated.

Item :reset
Function :Sets the LEVEL and CONTROL FREQ. values to

factory-preset ones.

2. SLOT CONDITION

Displays the status of the input
cards installed in each of the
input card slots. Press the
button to display the setting
menu illustrated on the right.

<SLOT CONDITION>

INPUT A : VIDEO-1
INPUT B : VIDEO-2
INPUT C : COMPO.
INPUT D : RGB
INPUT E : NO SLOT
INPUT F : NO SLOT

EXIT: MENU

Items :INPUT A:/INPUT B:/INPUT C:/INPUT D:/INPUT

E:/INPUT F:

Settings : VIDEO-1/VIDEO-2/COMPO./RGB/SDI 1/SDI 2/

HD SDI 1/HD SDI 2/HD SDI 1*/HD SDI 2*/NO
SLOT

Function :Displays the status of the input cards installed in

each of the input card slots.

● INPUT A/B corresponds to SLOT 1, INPUT C/D to SLOT 2,
and INPUT E/F to SLOT 3.

● VIDEO-1 or VIDEO-2 shows the video input card is in­stalled. COMPO. or RGB shows the component/RGB input
card.
SDI 1 or SDI 2 shows the SDI input card is installed.
HD SDI 1 or HD SDI 2 shows the HD SDI input card is
installed.
HD SDI 1* and HD SDI 2* show the HD SDI input card
(compatible with EMBEDDED AUDIO) is installed.

● NO SLOT shows no input cards are installed.

13

HOW TO USE “MAIN MENU” (cont'd)

5. AREA MARKER-R

Items :Selects the size marker for the other screen ratio

(aspect) used when the screen ratio is 16:9. (for

external control)
Settings :OFF/16:9/4:3/13:9/14:9/MODE 1/MODE 2
Functions : OFF: The marker is not displayed.

16:9/4:3/13:9/14:9: Displays the marker (a white

quadrangle) showing the screen size of each

aspect ratio.

MODE 1/MODE 2: Displays no markers because

these settings will be used for function expansion

in the future.

●AREA MARKER-R is displayed when a 16:9 picture such
as 1080i/1035i/720p etc. is displayed or the picture is
switched to the 16:9 screen ratio by pressing the ASPECT
button.

●The marker is actually displayed when the external control
selects each setting. (No markers are displayed even if
each marker is selected only in the monitor’s AREA
MARKER-R setting.)

6. CENTER MARKER

Items :Makes the center marker appear or disappear.
Settings :ON/OFF
Functions : ON :The center marker (a white cross) is

displayed on the center of the screen.

OFF :The marker disappears.

●To actually display the marker, the AREA MARKER
button on the monitor needs to be pressed so that it is
illuminated.

R-Y PHASE 90

ITU601

R/B GAIN 0.79
G-Y PHASE 244
G/B GAIN 0.45
R-Y PHASE 90

ITU709

R/B GAIN 0.86
G-Y PHASE 244
G/B GAIN 0.30

Item :SELECT
Function :Selects the picture matrix standard.
Settings : ITU601 or ITU709/ MANUAL

ITU601 or ITU709 : Standard setting
MANUAL :Manual setting

NOTE :The following items are displayed when MANUAL is

selected. When ITU601 or ITU709 is selected, they
are not displayed.

Item :R-Y PHASE
Function :Sets the R-Y phase.
Settings : 90/92/94/112

Item :R/B GAIN
Function :Sets the R/B gain.
Settings : 0.86/0.56/0.68/0.79

Item :G-Y PHASE
Function :Sets the G-Y phase.
Settings : 244/253/236/240

Center marker

7. COLOR MATRIX

Selects or adjusts the
standard of the color
demodulation (color
rendering). Press the
button to display the setting
menu illustrated on the right.

● The standard setting is set to “ITU601” or “ITU709”
depending on the input signal format.
The factory preset of MANUAL is ITU709

Input Signal Format Standard Manual

NTSC, PAL, 480/60i,
480/60p, 576/50i, 575/50p

720/60p, 1080/50i, 1080/60i,
1035/60i, 1080/24psF

<COLOR MATRIX>

SELECT :MANUAL
R-Y PHASE : 90
R/B GAIN :0.86
G-Y PHASE : 244
G/B GAIN :0.36
sub menu
reset

EXIT:

MENU

ADJUST:- + SELECT:

The menu screen when

MANUAL is selected.

setting setting

ITU601

ITU709

Item :G/B GAIN
Function :Sets the G-B gain.
Settings : 0.30/0.34/0.40/0.45

Item :sub menu
Function :Performs the R-Y PHASE, R/B GAIN, G-Y

PHASE or G/B GAIN settings in a single-line
display. The display position depends on the
“sub menu POSITION” setting.

Settings : Same as R-Y PHASE, R/B GAIN, G-Y PHASE or

G/B GAIN

Item :reset
Function :Sets the R-Y PHASE, R/B GAIN, G-Y PHASE

and G/B GAIN values to factory-preset ones.

(MANUAL)

ITU709

14

HOW TO USE “SETUP MENU”

䡵 “SETUP MENU” ITEMS

Items Functions

1 FUNCTION SETTING Displays the monitor’s power-up time or the total usage time.
2 PICTURE SUB ADJ. Performs approximate adjustments using the control knobs on the front panel.
3 COLOR TEMP./BAL. Sets or adjusts the color temperature or white balance.
4 SIZE/POSI. ADJ. Adjusts the size or position of the picture.
5 DISTORTION ADJ. Compensates the picture distortion.
6 STATUS DISPLAY Makes the status of the input signal appear or disappear on the screen.
7 CONTROL LOCK Sets the control lock preventing the monitor from misuse.
8 all reset Sets all items in SETUP MENU to factory-preset values.

䡵 “SETUP MENU” SCREENS

<SETUP MENU>

FUNCTION SETTING
PICTURE SUB ADJ.
COLOR TEMP./BAL.
SIZE/POSI.ADJ.
DISTORTION ADJ.
STATUS DISPLAY
CONTROL LOCK :ON
all reset

MENU

ENTER:+ SELECT:

EXIT:

<FUNCTION SETTING>

COLOR SYSTEM :AUTO
SYNC SELECT :AUTO
RUSH DELAY TIME :STD.
TALLY SELECT :GREEN
REMOTE SYSTEM :MAKE
EMBEDDED :1G
HOUR METER X100h :000

MENU

ADJUST:- + SELECT:

EXIT:

<PICTURE SUB ADJ.>

CONTRAST : 00
BRIGHT : 00
CHROMA : 00
PHASE : 00
NTSC SETUP : 00
COMPO.LEVEL :SMPTE
sub menu
reset

MENU

ADJUST:- + SELECT:

EXIT:

<COLOR TEMP./BAL.>

COLOR TEMP. :LOW
BLUE DRIVE : 000
RED DRIVE : 000
GREEN CUTOFF : 000
BLUE CUTOFF : 000
RED CUTOFF : 000
sub menu
reset

MENU

ADJUST:- + SELECT:

EXIT:

<SIZE/POSI. ADJ.>

H.SIZE : 00
H.POSITION : 00
V.SIZE : 00
V.POSITION : 00
sub menu
reset

MENU

ADJUST:- + SELECT:

EXIT:

CONTRAST : 00

- - + +

BLUE DRIVE :000

- - + +

H.SIZE : 00

- - + +

<DISTORTION ADJ.>

PINCUSHION : 00
PIN.BALANCE : 00
PARALLELOGRAM : 00
TRAPEZOID : 00
ROTATION : 00
sub menu
reset

MENU

ADJUST:- + SELECT:

EXIT:

<STATUS DISPLAY>

STATUS DISPLAY :ON
1080/1035 :1080

MENU

ADJUST:- + SELECT:

EXIT:

PINCUSHION : 00

- - + +

Aer you sure ?
"Yes" then + Key.

MENU

"No" then

Key.

15

HOW TO USE “SETUP MENU” (cont'd)

䡵 ITEM CONTENTS AND ADJUSTMENT RANGE/SETTINGS

1. FUNCTION SETTING

Selects the color system and
displays the monitor’s power­up time or the total usage time.
Press the
the setting menu illustrated on
the right.

button to display

<FUNCTION SETTING>

COLOR SYSTEM :AUTO
SYNC SELECT :AUTO
RUSH DELAY TIME :STD.
TALLY SELECT :GREEN
REMOTE SYSTEM :MAKE
EMBEDDED :1G
HOUR METER X100h :000

MENU

ADJUST:- + SELECT:

EXIT:

Item :COLOR SYSTEM
Settings : AUTO/NTSC/PAL
Function :Selects the color system when using the video

input card.
AUTO : Change NTSC and PAL automatically.
NTSC : Keeps the color system NTSC.
PAL : Keeps the color system PAL.

NOTE :Normally select AUTO. However, if the input signal is

unstable, select NTSC or PAL.

Item :SYNC SELECT
Settings : AUTO/INT.
Function :Select the detection method for synchronized

signals.
AUTO : If a synchronized signal is input from

external synchronized signal terminals,
the input video signal is synchronized
with it. If no synchronized signal is input,
the input video signal is synchronized
with its own built-in sync signal.

INT. :The input video signal is always synchro-

nized with the built-in sync signal.

* The external synchronized signal terminals apply to the HD/

CS terminal and VD terminal (in the RGB/COMPONENT
Input Card), or the EXT. SYNC terminal (in the VIDEO Input
Card).

Item :RUSH DELAY TIME
Settings : STD./SLOW
Function :Sets the time when the power supply to the

monitor’s circuits (excluding the micro computers)
starts after the power switch is pressed.
STD. : The power supply starts approx.

1 second after the power switch is
pressed.

SLOW : The power supply starts approx.

3.2 seconds after the power switch is
pressed.

NOTE :When turning on many Multi-Format Monitors

simultaneously, it is recommended to use SLOW to
control rush current.

Item :TALLY SELECT
Settings : GREEN/RED
Function :Selects the color of the tally lamp (when lit) on

the upper front panel.
GREEN: The tally lamp lights in green.
RED :The tally lamp lights in red.

NOTE :Set the MAKE/TRIGGER terminal’s tally control in the

REMOTE (external control) terminal setup menu. For
details, refer to Page 20. To set the color, use TALLY
SELECT in the "FUNCTION SETTING" setup menu or
MAKE/TRIGGER in the REMOTE (external control)
terminal setup menu. For details, refer to Page 16
and 20.

Item :REMOTE SYSTEM
Settings : MAKE/TRIGGER
Function :Selects the contact system (MAKE (make

contact) or TRG. (trigger contact)) for the MAKE/
TRIGGER terminals.
MAKE (make contact system): Controls the

function by stable disconnection (terminal
open) or short-circuit (short with GND of 15th
terminal) of the controlled terminal.

TRG. (trigger system): Controls the function by

instantaneously (one second) short-circuiting
(short with GND of 15th terminal) the
controlled terminal.

Item :EMBEDDED
Settings : 1G/2G/1-2G
Function : Selects AES/EBU Embedded Audio signal

channels.

NOTE:The auto setting mixes and outputs all 8 signal

channels. Output level is automatically detected and
set at FPGA according to the channel numbers that

are receiving signals.
* About sound output level
Sound output level is set to a standard output level for all
channels when several sound channels are output at the
same time. The more channels are selected, the lower each
channel’s level will be.
(Each channel's level becomes half for 1– 2 channel, 1/4 for
1– 4 channel.)
*About AUTO
When AUTO is selected, the number of sound channels in use
is detected. The level of each channel is automatically
adjusted to ensure that the total sound output level is equiva­lent to the standard output level.

Item :HOUR METER X100h
Number
range : 000 ~ 655
Function :Displays the total usage time of the monitor in

hundred-hour units.

● When the timer passes 655, it returns to 000.

● The timer does not count the usage time under one hour.

2. PICTURE SUB ADJ.

Performs approximate
adjustments using the control
knobs on the front panel. Press

button to display the

the
setting menu illustrated on the
right.

NOTE : When the RGB signal

is input, only
CONTRAST and
BRIGHT are displayed. When the PAL signal is
input, only CONTRAST, BRIGHT and CHROMA are
displayed.

<PICTURE SUB ADJ.>

CONTRAST : 00
BRIGHT : 00
CHROMA : 00
PHASE : 00
NTSC SETUP : 00
COMPO.LEVEL :SMPTE
sub menu
reset

MENU

ADJUST:- + SELECT:

EXIT:

16

Item :CONTRAST
Adjustment
range :–20 ~ 00 ~ +20
Function :For approximate adjustment of the picture

contrast. Before adjustment, set the CON­TRAST knob on the front panel to 0.

Item :BRIGHT
Adjustment
range :–20 ~ 00 ~ +20
Function :For approximate adjustment of the picture

brightness. Before adjustment, set the BRIGHT
knob on the front panel to 0.

Item :CHROMA
Adjustment
range :–20 ~ 00 ~ +20
Function :For approximate adjustment of the color

density. Before adjustment, set the CHROMA
knob on the front panel to 0.

Item :PHASE
Adjustment
range :–20 ~ 00 ~ +20
Function :For approximate adjustment of the picture hue.

Before adjustment, set the PHASE knob on the
front panel to 0.

Item :NTSC SETUP
Settings : 00/7.5
Function :Sets the level of the input NTSC signal.

00 : Compliant with 0% set-up signal.
75 : Compliant with 7.5% set-up signal.

NOTE :NTSC SETUP is displayed only when the video input

card is installed and an NTSC signal is input.

Item :COMPO. LEVEL
Settings : SMPTE/B75/B00
Function :Sets the level of the input component signal.

SMPTE:Compliant with M2VTR signals.
B75 :Compliant with Betacam 7.5% set-up

signal.

B00 :Compliant with Betacam 0% set-up

signal.

NOTE :COMPO. LEVEL is displayed only when a 480/60i,

480/60p, 576/50i or 576/50p signal is input.

Item :sub menu
Adjustment range/
Settings : Same as CONTRAST, BRIGHT, CHROMA,

PHASE and COMPO LEVEL/NTSC SETUP.

Function :Performs CONTRAST, BRIGHT, CHROMA,

PHASE or COMPO LEVEL/NTSC SETUP
settings in a single-line display. The sub menu
display varies depending on the selected item.

3. COLOR TEMP./BAL.

Sets or adjusts the color
temperature or white balance.
Press the button to display
the setting menu illustrated on
the right.

Item :COLOR TEMP.
Settings : HIGH/LOW
Function :Selects the color temperature.

HIGH:Sets the color temperature to D93.
LOW : Sets the color temperature to D65.

Item :BLUE DRIVE
Adjustment
range : MIN ~ 000 ~ MAX (in 127 grades)
Function :Adjusts the blue drive level.

Item :RED DRIVE
Adjustment
range : MIN ~ 000 ~ MAX (in 127 grades)
Function :Adjusts the red drive level.

Item :GREEN CUTOFF
Adjustment
range : MIN ~ 000 ~ MAX (in 255 grades)
Function :Sets the green cut-off point.

Item : BLUE CUTOFF
Adjustment
range : MIN ~ 000 ~ MAX (in 255 grades)
Function :Sets the blue cut-off point.

Item :RED CUTOFF
Adjustment
range : MIN ~ 000 ~ MAX (in 255 grades)
Function :Sets the red cut-off point.

Item :sub menu
Adjustment range/
Settings : Same as BLUE DRIVE, RED DRIVE, GREEN

CUTOFF, BLUE CUTOFF and RED CUTOFF.

Function :Performs BLUE DRIVE, RED DRIVE, GREEN

CUTOFF, BLUE CUTOFF or RED CUTOFF
settings in a single-line display. The sub menu
display varies depending on the selected item.

Item :reset
Function :Sets the BLUE DRIVE, RED DRIVE, GREEN

CUTOFF, BLUE CUTOFF and RED CUTOFF
values to factory-preset ones.

<COLOR TEMP./BAL.>

COLOR TEMP. :LOW
BLUE DRIVE : 000
RED DRIVE : 000
GREEN CUTOFF : 000
BLUE CUTOFF : 000
RED CUTOFF : 000
sub menu
reset

MENU

ADJUST:- + SELECT:

EXIT:

Item :reset
Function :Sets the CONTRAST, BRIGHT, CHROMA,

PHASE and COMPO LEVEL/NTSC SETUP
values to factory-preset ones.

17

HOW TO USE “SETUP MENU” (cont'd)

4. SIZE/POSI. ADJ.

Adjusts the size or position of
the picture. Press the
button to display the setting
menu illustrated on the right.

Item :H.SIZE
Adjustment
range :–20 ~ 00 ~ +20 (*)
Function :Adjusts the horizontal screen size.

– : Reduces the screen size horizontally.
+ :Enlarges the screen size horizontally.

*Reduced to 00 ~ +20 during the under-scanmode.
Item :H.POSITION

Adjustment
range :–20 ~ 00 ~ +20
Function :Adjusts the horizontal screen position.

– : Move the screen to the left.
+ :Move the screen to the right.

Item :V.SIZE
Adjustment
range :–20 ~ 00 ~ +20
Function :Adjusts the vertical screen size.

– : Reduces the screen size vertically.
+ :Enlarges the screen size vertically.

Item :V.POSITION
Adjustment
range :–20 ~ 00 ~ +20
Function :Adjusts the vertical screen position.

– : Move the screen up.
+ :Move the screen down.

Item :sub menu
Adjustment range/
Settings : Same as H.SIZE, H.POSITION, V.SIZE and

V.POSITION.

Function :Performs H.SIZE, H.POSITION, V.SIZE or

V.POSITION settings in a single-line display. The
sub menu display varies depending on the
selected item.

Item :reset
Function :Sets the H.SIZE, H.POSITION, V.SIZE and

V.POSITION values to factory-preset ones.

<SIZE/POSI. ADJ.>

H.SIZE : 00
H.POSITION : 00
V.SIZE : 00
V.POSITION : 00
sub menu
reset

MENU

ADJUST:- + SELECT:

EXIT:

5. DISTORTION ADJ.

Compensates the picture
distortion. Press the

button
to display the setting menu
illustrated on the right.

Item :PINCUSHION
Adjustment
range : –20 ~ 00 ~ +20
Function :Compensates pincushion picture distortion.

– : Expands both left and right sides of the

picture.

+ :Squeezes both left and right sides of the

picture.

Item :PIN.BALANCE
Adjustment
range : –20 ~ 00 ~ +20
Function :Adjusts the compensation balance of the

pincushion picture distortion.
– : The picture is expanded on the left side, and

squeezed on the right side.

+ :The picture is squeezed on the left side, and

expanded on the right side.

Item :PARALLELOGRAM
Adjustment
range : –20 ~ 00 ~ +20
Function :Compensates parallelogram picture

distortion.
– : Moves the upper side of the picture to the

right, and the lower side to the left.

+ :Moves the upper side of the picture to the left,

and the lower side to the right.

Item :TRAPEZOID
Adjustment
range : –20 ~ 00 ~ +20
Function :Compensates trapezoid picture distortion.

– : Enlarges the upper side of the picture.
+ : Reduces the upper side of the picture.

Item :ROTATION
Adjustment
range : –31 ~ 00 ~ +31
Function :Compensates for picture tilt.

– : Turns the picture clockwise.
+ : Turns the picture counterclockwise.

<DISTORTION ADJ.>

PINCUSHION : 00
PIN.BALANCE : 00
PARALLELOGRAM : 00
TRAPEZOID : 00
ROTATION : 00
sub menu
reset

EXIT:

MENU

ADJUST:- + SELECT:

18

Item :sub menu
Adjustment range/
Settings : Same as PINCUSHION, PIN.BALANCE, PARAL-

LELOGRAM, TRAPEZOID and ROTATION.

Function :Performs PINCUSHION, PIN.BALANCE,

PARALLELOGRAM, TRAPEZOID or ROTATION
settings in a single-line display. The sub menu
display varies depending on the selected item.

Item :reset
Function :Sets the PINCUSHION, PIN.BALANCE,

PARALLELOGRAM, TRAPEZOID and ROTATION
values to factory-preset ones.

6. ST ATUS DISPLA Y

Makes the status of the input
signal appear or disappear on
the screen. Press the
button to display the setting
menu illustrated on the right.

Item :STATUS DISPLAY
Settings : ON/OFF
Function :Makes the format name appear or disappear

when signals are input and the signal status
appear or disappear when the input signal is
changed.
ON : The information is displayed.
OFF: The information is not displayed.

Item :1080/1035
Settings : 1080/1035
Function :Makes the number of effective scanning lines

appear or disappear when the HDTV signal is
input.
1080 :Sets the number to 1080. (Select when

the digital HDTV signal is input.)

1035 :Sets the number to 1035. (Select when

the analog HDTV signal is input.)

<STATUS DISPLAY>

STATUS DISPLAY :ON
1080/1035 :1080

MENU

ADJUST:- + SELECT:

EXIT:

7. CONTROL LOCK

Item :CONTROL LOCK
Settings :OFF/ON
Function : Invalidates most of operations on the front panel

(including menu screen operations).
OFF: Enables normal operations.
ON : Invalidates all operations except the power

switch and CONTROL LOCK.

NOTE: While CONTROL LOCK is set to ON, attempting to

perform any operation except power switch and
CONTROL LOCK causes the “

Control lock on!”
warning to appear on the screen for approx. 3
seconds. (It is possible to operate the power switch
and display SETUP MENU.)
When SETUP MENU is displayed while CONTROL

4

LOCK is set to ON, the cursor (

) is located next to
CONTROL LOCK and cannot be moved.

8. all reset

Function : Sets all items in SETUP MENU to factory-preset

values.

19

HOW TO USE EXTERNAL
CONTROL

䡵 ABOUT EXTERNAL CONTROL

The Multi-Format Monitor has two external control terminals.
One is the MAKE/TRIGGER terminal, which allows the monitor to be controlled by the MAKE(make contact) or TRG. (trigger
contact) method selected in the function setting.
MAKE (make contact system): Controls the function by stable disconnection (terminal open) or short-circuiting (short with GND of

15th terminal) of the controlled terminal.

TRG. (trigger system) : Controls the function by instantaneously (one second) short-circuiting (short with GND of 15th

terminal) the controlled terminal.
* MAKE or TRIGGER are selected from REMOTE SELECT in the setup menu.
* The 14th terminal (REMOTE ENABLE) is always controlled by the make contact system regardless of the REMOTE SELECT

setting.
The other terminal used for remote control is the RS-232C terminal. This allows the monitor to be controlled by a PC via serial
communication.

NOTE: Control priority is in the following order; 1 MAKE/TRIGGER terminal > 2 RS-232C terminal > 3 front panel buttons.

When trigger contact is on, the front panel buttons can be operated.

䡵 HOW TO USE THE MAKE/TRIGGER TERMINAL

Connections

Connect (short-circuit) the 15th terminal (GND) to each of the 1st through 14th terminals in the 3-line

15-pin D-sub connector. The functions of each terminal are listed below.

The Names and Functions of T erminals

No. Names Functions Operations (OFF p[ ON) *1

1 TALLY Puts on the tally lamp. Put off Put on
2 INPUT A Changes the input to INPUT A Not change Change
3 INPUT B Changes the input to INPUT B Not change Change
4 INPUT C Changes the input to INPUT C Not change Change
5 INPUT D Changes the input to INPUT D Not change Change
6 INPUT E Changes the input to INPUT E Not change Change
7 INPUT F Changes the input to INPUT F Not change Change
8 COLOR OFF Changes the picture black-and-white. Not change Change
9 AREA MARKER Displays the area marker. Not display Display
10 ASPECT Changes the screen ratio to 16:9 4:3 16:9
11 TALLY SELECT Switch the tally lamp color. GREEN RED
12 MARKER Selects the type of the area marker Selection in the main unit Selection in the remote *2

13 STATUS Displays the monitor’s status Display *3
14 REMOTE ENABLE Makes the external control form the Invalid Valid *4

15 GND Used as a ground terminal – –

*1 : OFF stands for disconnection, and ON stands for short-circuit.

When trigger contact is on, the setting switches between ON and OFF every time the terminal is short-circuited.
(Only TALLY is controlled by being OFF(disconnection) and ON(short-circuit).)

*2 : Selects the area marker size from AREA MARKER (setting on the main unit) or AREA MARKER-R (setting on the remote control) setting.
*3 : The STATUS function is activated when the connection to the STATUS terminal is changed (ON to OFF, or OFF to ON). The monitor’s status is displayed for 3

seconds.

*4 : Setting REMOTE ENABLE to ON enables remote control. (same for both MAKE/TRIGGER methods.)

MAKE terminal valid or invalid

control

10 9 8

54321

1415 13 12 11

7

6

Operation

1. Set REMOTE ENABLE to ON.

2. Short-circuit or disconnect the desired terminal. (When trigger contact is on, duration of short-circuit is approx. 1 second.)

Changing the Signal Input

1. Set REMOTE ENABLE to ON.

2. Short-circuit the desired INPUT terminal. (When trigger contact is on, duration of short-circuit is approx. 1 second.)

3. Disconnect the INPUT terminal selected above. The signal input is actually changed after the disconnection has been
completed.

NOTES: • When more than two terminals are selected (short-circuited) from INPUT A through INPUT F, the signal input is not changed.

To control INPUT A through INPUT F, we recommend using the interlock switch, which turns off a switch when another switch is turned on.

•When trigger contact is on, and if several terminals are short-circuited simultaneously, proper control cannot be done. It is always
necessary to short-circuit one terminal for one operation. Also, use of the Tact Switch is recommended.

20

䡵 HOW TO USE THE RS-232C TERMINAL

You can control the monitor from your PC via the RS-232C terminal.
For details on operating the monitor from the PC, consult your dealer or service center for details.

1. Cable

Prepare a straight cable with a D-sub connector (9-pin, female) and a D-sub
connector (9-pin, male)

2. Communications Specifications

Baud Rate : 4800/9600/19200 (factory pre-set; 4800)
Data Bits : 8 bits
Parity : No parity
Stop Bits : 1
Flow Control : Hardware (RTS/CTS)

3. Commands

Format

Header ID Command Data CR

Header

! Control from the PC to the monitor

? Reference from the PC to the monitor

@ Answer from the monitor to the PC

ID + Command + Data

B Basic command Characters 00, 01 or No data

D Command for adjusting the picture size 00 ~ 08 –20 ~ +20 or –31 ~ +31

S Command for adjusting the picture quality 00 ~ 05 –20 ~ +20

M Command for selecting the menu item 00 ~ 0E 00, 01, 10, 11

F Command for selecting the menu item 00 ~ 0A 00, 01

W Command for adjusting the white balance 00 ~ 05 –256 ~ +255

C Command for inquiring for the monitor’s status 00 0 ~ 655

Pin No. Signal

1 DCD (Data Carrier Detect)
2 RD (Receive Data)
3 TD (Transmit Data)
4 DTR (Data Terminal Ready)
5 GND (Ground)
6 DSR (Data Set Ready)
7 RTS (Request To Send)
8 CTS (Clear To Send)
9 RI (Ring Indication)

9
8

7
6

5

4
3
2
1

During Communication from the PC to the Monitor

The monitor receives the data when DSR remains ON (high) and CTS is set to ON.
During Communication from the Monitor to the PC
The monitor sends the data when both DSR and DCD are set to ON and RTS is set to ON.

Communication Procedures

The following is the communication procedures.

1. Starting the communication
Receives the connection command (!BCN1Cr) from the PC [ Sends the monitor’s status (@BOKCr) to the PC

2. Performing the external control
Receives the control command (!XXXXCr) from the PC [ Sends the monitor’s status (@BOKCr) to the PC
* The monitor repeats these receiving and sending if necessary.

3. Terminating the communication
Receives the termination command (!BCN0Cr) [ Sends the monitor’s status (@BOKCr) to the PC

* After sending the data to the monitor, the PC must first receive the data from the monitor and then send the next command

because the communication is performed in a hand-shake system. If the PC does not receive the status from the monitor after
sending the command, re-send the command.

21

TROUBLESHOOTING

Solutions to common problems related to your monitor are described here. If none of the solutions presented here solve
the problem, unplug the monitor and consult a JVC-authorized dealer or service center for assistance.

Problems

No power supply

No picture with
the power on

No sound

Wrong color

Unnatural picture

Shaking picture

Points to be checked

Is the power plug loosened or
disconnected?

Is the main power turned OFF?
Is the signal cable disconnected?
Is the power of the connected

component ON?
Is the signal output from the connected
component?

Is the input signal selected correctly?

Is the input signal adapted to the
monitor’s specification?

Are any of the self-check indicators
(INPUT SELECT A through F buttons)
blinking?

Is the audio cable disconnected?
Is the audio signal output from the

connected component?
Is the volume output set to minimum?

Has the picture adjustment been
changed?

Has the WHITE BALANCE setting
been changed?

Are any cables connected to the
component/RGB input card?

Has the correct signal been input to the
component/RGB input card and the
correct INPUT been selected on the
monitor?

Has [CONTRAST] or [BRIGHT] been
changed?

Is the monitor close to a motor,
transformer or any other device
generating a strong magnetic field?
(a fan, fluorescent light, laser printer,
another monitor, etc.)

Measures (Remedy)

Firmly insert the power plug.

Turn the main power ON.
Connect the signal cable firmly.
Turn on the power of the connected component

and set it correctly.

Select the correct input with the INPUT SELECT
buttons.

Check that the input signal format corresponds to
the installed input card format.

Follow the procedures in “SELF-CHECK
INDICATIONS”.

Connect the audio cable firmly.
Set the connected component correctly.

Adjust the speaker volume with the VOLUME
+/– buttons.

Set each picture adjustment knob to the standard
(centered) position. Or, set each picture
adjustment item in [ PICTURE SUB ADJ.] in the
<SET UP MENU> screen to Standard (00) (or
use the [reset] function).

Set each [COLOR TEMP./BAL.] item in the
<SET-UP MENU> screen to Standard (000) (or
use the [reset] function).

Connect each signal cable firmly.

Select INPUT A/C when the component signal is
input, or select INPUT B/D/F when the RGB
signal is input.

Adjust the CONTRAST or BRIGHT picture
adjustment knobs.
Or, adjust the [CONTRAST] or [BRIGHT] item in
[PICTURE SUB ADJ.] in the <SET-UP MENU>
screen.

Move the monitor away from the device until the
picture stops shaking.

Connect the power plug to another AC outlet
away from the former one.

Reference
pages

5
5

6, 8

—

5

6, 8

24

6, 8

—

4

4, 16

17

6

6

17

—

22

Problems

Irregular color

Wrong picture
position, wrong
picture size

Front panel
buttons and
knobs do not
function

Points to be checked

Is the monitor placed or moved close to
a speaker or any other device

incorporating a magnet?
Has the position of the monitor been

changed with the power on?
Has the picture position, size or

distortion been changed?

Have the UNDER SCAN or ASPECT
button been pressed?

Has the CONTROL LOCK function
been set to ON?

Has the monitor’s setting been
changed to enable control from an
external unit via the REMOTE
terminals?

Measures (Remedy)

Move the device away from the monitor.
Press the DEGAUSS button on the front panel to
degauss the screen.
When degaussing, wait more than 30 minutes for
maximum effect.

Adjust the picture size (H SIZE, V SIZE) or
position (H. POSITION, V. POSITION) in the
[SIZE/POSI. ADJ.] item in the <SETUP MENU>
screen.
Adjust the picture distortion (PINCUSHION, PIN.
BALANCE, TRAPEZOID and P ARALLELOGRAM)
in the [DISTORTION ADJ.] item in the <SETUP
MENU> screen.

It may not be possible to expand the picture due
to the selected input mode. In this case,

adjustment is impossible.
When the UNDER SCAN or ASPECT button is

lit, press each button to invalidate each setting.
Set the CONTROL LOCK function to OFF.

Change the setting of the external control to
control the monitor locally.

Reference

pages

4

18

4, 5

19

20, 21

The following are not malfunctions:

● You may see two horizontal lines on the monitor. They are
the shadows of the “damper lines” that are necessary for
composing the monitor. These lines are not a malfunction.

● When a bright still image (such as a white cloth) is
displayed for a long period, it may appear to be colored.
This is due to the structure of the cathode ray tube and
will disappear when another image is displayed.

● You may sometimes experience a mild electric shock
when you touch the picture tube. This phenomenon is due
to a normal buildup of static electricity on the CRT and is
not harmful.

● The monitor emits a strange sound when the room
temperature changes suddenly. This is only a problem if

Damper line

an abnormality appears on the screen as well.

● If two or more monitors are operated next to each other,
their images may shake or be distorted. This phenomenon
is due to mutual interference; it is not a malfunction. Move

UNDER

PULSE

COLOR

DEGAUSS

SCAN

CROSS

OFF

MUTING

VOLUME

SLOT 1

A

ASPECT

MENU

SCREENS

AREA

CHECK

MARKER

POWER

SLOT 2

SLOT 3

C

B

E

D

F

INPUT SELECT

the monitors away from each other until the interference
disappears or turn the power off on any monitor that is not
being used.

When black vertical lines appear on the screen

Black vertical lines may appear on the screen if the aperture grill is tilted as a result of being shaken or jolted during shipment.

In this case, try tapping the monitor on the side. If this does get rid of the lines, follow the procedure below.

1. Display a white screen, so that the problem area can be seen clearly.

2. Maximize contrast and brightness, then place a bright white rectangle on the area.

3. After a while, the lines should disappear.

23

TROUBLESHOOTING (cont'd)

䡵 SELF-CHECK INDICATIONS

When the screen goes blank, and one or more of the INPUT SELECT A through F buttons on the front control panel start
blinking...

This monitor has a self-check function, which allows it to detect malfunctions and alert you. This makes trouble-shooting easier.
Whenever a problem occurs, a combination of “self-check indicators” (INPUT SELECT A through F buttons) will blink and the
monitor’s power automatically turns off. If this happens, follow the steps below and contact your dealer to resolve the problem.

A

SLOT 1

B

SLOT 2

C

SLOT 3

D

E

F

INPUT SELECT

UNDER

PULSE

COLOR

DEGAUSS

SCAN

CROSS

OFF

MUTING

VOLUME

SLOT 1

A

ASPECT

MENU

SCREENS

AREA

CHECK

MARKER

POWER

SLOT 2

SLOT 3

C

B

D

E

F

INPUT SELECT

1. Check which indicators are blinking.

2. Turn off the main power switch on the back of the monitor.

3. Disconnect the Power Cord from the AC outlet.

4. Contact your dealer with the information about which indicators are blinking.

NOTE:

● If you turn on the monitor’s power immediately after turning it off (or after a short-term power failure), the self-check indicators
may blink, and no image may be displayed.
When this happens, turn off the power, and wait at least 10 seconds before turning it on again. If the self-check indicators have
stopped blinking, you can use the monitor as usual.

24

SPECIFICATIONS

䡲 Type : Multi-Format Monitor
䡲 Picture Tube : 19" measured diagonally
䡲 Effective

Screen Size : Width :14-5/8" (370 mm)

Height :10-5/8" (270 mm)
Diagonal :18-1/8" (460 mm)

䡲 Scanning

Frequency : H : 15 kHz/15 kHz – 45 kHz

V : 50 Hz – 100 Hz

䡲 Video Band : Component :25 MHz (–3 dB)

Video (Y/C) :8 MHz (–3 dB)

䡲 Horizontal

Resolution : Video (Y/C) : 600 TV lines

1080/60i :900 TV lines

䡲 Input

Terminals : Installing an optional input card in SLOT 1,

2, or 3 is required.
INPUT A/INPUT B: Terminals on the input

card in SLOT 1

INPUT C/INPUT D: Terminals on the input

card in SLOT 2

INPUT E/INPUT F: Terminals on the input

card in SLOT 3

䡲 Compliant

Video Signal : NTSC (3.58 MHz)/PAL (4.43 MHz)

(using the IF-C01PNG)
480i/576i/480p/576p/1080i (50 HZ/60 HZ/
24psF)/720p (using the IF-C01COMG)
D1 serial digital (using the IF-C01SDG)
HD serial digital (using the IF-C01HSDG/
IF-C12HSDG))

䡲

Remote Inputs

: • Point-of-contact connection, 1 line,

D-sub connector (15-pin 3-line)

• Serial connection, 1 line, D-sub connector
(9-pin), compliant to RS-232C

䡲 Audio Output : 1 W (monaural)
䡲 Built-in

Speaker : 3-1/8" (8 cm) round x 1

䡲 Environmental

Conditions : Operating temperature :5°C – 35°C

(41°F – 95° F)

Operating humidity : 20% – 80%

(non-condensing)

䡲 Power

Requirements

: 120 V/230 V AC, 50 Hz/60 Hz

䡲 Power

Consumption: 1.8A /1.0 A (when input card is inserted)

Max. 2.1 A/1.2 A (when input card is
inserted)

䡲 Dimensions : Width : 17-3/8" (440 mm)

Height : 14-7/8" (375 mm)
Depth : 19-5/8" (496 mm)
(not including wide mask and input card)

䡲 Weight : 64.7 lbs (29.4 kg)

(not including wide mask and input card)

䡲 Accessory : AC power cord

: Power cord holder x 1 (case and cover)
: Screws x 2 (Power cord holder)
: Wide Mask x 1
: Screws x 4 (Wide Mask)

[Dimensions]

Unit : inch (mm)

<Front View with the wide mask attached>

14-3/4" (372)

<Front View>

14-7/8" (377)

8-1/8" (206)

UNDER

PULSE

COLOR

DEGAUSS

SCAN

CROSS

OFF

MUTING

VOLUME

17-3/8" (440) 19-5/8" (496)

MUTING

VOLUME

15" (380.4)

ASPECT

MENU

SCREENS
CHECK

MARKER

11-1/4" (285)

UNDER

PULSE

COLOR

DEGAUSS

SCAN

CROSS

ASPECT

MENU

SCREENS
CHECK

MARKER

SLOT 1

A

B

AREA

OFF

SLOT 1

A

B

AREA

INPUT SELECT

INPUT SELECT

POWER

SLOT 2

SLOT 3

C

E

D

F

POWER

SLOT 2

SLOT 3

C

E

D

F

<Side View>

14-7/8" (375)

3-7/8"
(95.7)

* Illustrations and pictures used in this manual have been

exaggerated, abbreviated or compounded for explanatory purposes

only. The appearance of the actual product may differ slightly.
* Dimensions and weight are approximate.
* E. & O.E. Design and specifications subject to change without

notice.

13-1/4" (336)

25

SPECIFICATIONS (cont'd)

䡵 Compliant Signal Formats of Each Input Card

Input Signals IF-C01PNG IF-C01COMG IF-C01SDG IF-C01HSDG IF-C12HSDG

NTSC (3.58 MHz) R ————
PAL (4.43 MHz) R ————
Black-and-White (50 Hz/60 Hz) R ————
480/60i (525i) — RR——
480/60p (525p) — R ———
576/50i — RR——
576/50p — R ———
720/60p (720p) — R — RR
1080/50i — R — RR
1080/60i (1125i) — R — RR
1035/60i (1125i) (*1) — 䡬 — 䡬䡬
1080/24psF — R — RR
EMBEDDED AUDIO ————R

R : Input possible. Pre-set.

䡬 : Input possible. Not pre-set.

– : Input impossible

*1: 1035/60i (1125i) is not pre-set. To input signals of these types, some setup adjustments are required.

APPENDIX: CONNECTION EXAMPLES FOR THE

SDI/HD SDI INPUT CARD (IF-C01SDG/
IF-C01HSDG only)

This section explains the usage precautions and connection examples when using the SWITCHED OUT terminal of the SDI/HD
SDI input card.

Usage Precautions

● The selected signal is output from the SWITCHED OUT terminal only when the monitor’s power is turned on.

● The output signal from the SWITCHED OUT terminal is the one that is selected from the signals input to SDI 1/HD SDI 1 or

SDI 2/HD SDI 2.
The table below shows the connection between the INPUT SELECT buttons (input signal selection) and the input/output of

the SDI/HD SDI input card.

Selected INPUT SELECT Buttons Signal Output from the SWITCHED OUT Terminal

A, C, E Signal from SDI 1/HD SDI 1
B, D, F Signal from SDI 2/HD SDI 2

26

SPECIFICATIONS

(INPUT CARD: OPTIONAL)

䡵 IF-C01COMG: COMPONENT/RGB INPUT CARD

Type : Component/RGB input card for Multi-Format Monitor
Inputs/Outputs : Component (Y, PB/B-Y, PR/R-Y) or RGB: 1 line, BNC connector x 6

(Y: 1 V (p-p), 75 Ω/PB, B-Y, PR, R-Y, R, G, B: 0.7 V (p-p), 75 Ω)
Synchronized signal (HD/CS, VD) : 1 line, BNC connector x 4 (1.0 V – 4.0 V (p-p), 75 Ω)
* The input (IN) and output (OUT) terminals are bridge-connected. Auto termination.
Audio signal: 1 line (monaural), RCA pin x 2 (0.5 V (rms), high impedance)
* The input (IN) and output (OUT) terminals are bridge-connected.

Required slots :1
Power consumption : 14 V DC, 0.02 A
Weight : 0.5 kg (1.1 lbs.)
Dimensions

(W x H x D) : 43 mm x 154.5 mm x 191.9 mm

(1-3/4" x 6-1/8" x 7-5/8")

䡵 IF-C01PNG: VIDEO INPUT CARD

Type : Video input card for Multi-Format Monitor
Inputs/Outputs : VIDEO 1/VIDEO 2: 2 lines, BNC connector x 4 (1 V (p-p), 75 Ω)

Synchronized signal (EXT.SYNC): 1 line, BNC connector x 2 (1.0 V – 4.0 V (p-p), 75 Ω)
* The input (IN) and output (OUT) terminals are bridge-connected. Auto termination.
Y/C signal :1 line, input only, mini-DIN 4-pin connector x 1 (Y/C input has a priority to a

VIDEO 2 input) (Y: 1 V (p-p), 75 Ω/C: 0.286 V (NTSC)/0.3 V (PAL), 75 Ω)
Audio signal : 2 lines (monaural), RCA pin x 4 (0.5 V (rms), high impedance)
* The input (IN) and output (OUT) terminals are bridge-connected.

Required slots :1
Power consumption : 14 V DC, 0.25 A

7 V DC, 0.15 A

Weight : 0.5 kg (1.1 lbs.)
Dimensions
(W x H x D) :43 mm x 154.5 mm x 191.9 mm

(1-3/4" x 6-1/8" x 7-5/8")

䡵 IF-C01SDG: SDI INPUT CARD

Type : SDI input card for Multi-Format Monitor
Inputs/Outputs : Digital input (SDI 1/SDI 2): 2 lines, BNC connector x 2 (0.8 V (p-p), 75 Ω)

Digital output (SWITCHED OUT): 1 line, BNC connector x 1 (0.8 V (p-p), 75 Ω)
Audio signal: 2 lines (monaural), RCA pin x 4 (0.5 V (rms), high impedance)
* The input (IN) and output (OUT) terminals are bridge-connected.

Format :D1 serial component digital, 525/625 auto switching (compliant to SMPTE259M)
Required slots :1
Power consumption : 7 V DC, 0.65 A
Weight : 0.5 kg (1.1 lbs.)
Dimensions

(W x H x D) :43 mm x 154.5 mm x 191.9 mm

(1-3/4" x 6-1/8" x 7-5/8")

27

SPECIFICATIONS

(INPUT CARD: OPTIONAL) (cont'd)

䡵 IF-C01HSDG: HD SDI INPUT CARD

Type : HD SDI input card for Multi-Format Monitor
Inputs/Outputs : Digital input (HD SDI 1/HD SDI 2): 2 lines, BNC connector x 2 (0.8 V (p-p), 75 Ω)

Digital output (SWITCHED OUT): 1 line, BNC connector x 1 (0.8 V (p-p), 75 Ω)
Audio signal: 1 line (monaural), RCA pin x 2 (0.5 V (rms), high impedance)
* The input (IN) and output (OUT) terminals are bridge-connected.

Format : HD serial component digital, BTAS-004B, SMPTE292M (Digital Interface Standard)
Required slots :1
Power consumption : 14 V DC, 0.72 A
Weight : 0.7 kg (1.54 lbs.)
Dimensions

(W x H x D) :43 mm x 154.5 mm x 200.2 mm

(1-3/4" x 6-1/8" x 7-7/8")

䡵 IF-C12HSDG: HD SDI INPUT CARD

Type : HD SDI input card for Multi-Format Monitor
Inputs/Outputs : Digital input (HD SDI 1/HD SDI 2): 2 lines, BNC connector x 2 (0.8V (p-p), 75 Ω)

(compliant with AES/EBU EMBEDDED AUDIO)
Digital output (HD SDI 1/HD SDI 2): 2 lines, BNC connector X 2 (0.8V (p-p), 75 Ω)

Format : HD serial component digital, BTAS-004B, SMPTE292M (Digital Interface Standard),

SMPTE299M (AES/EBU EMBEDDED AUDIO)

Required slots : 1
Power consumption : 14 V DC, 0.6A

7 V DC, 0.6A

Weight : 0.7 kg (1.54 lbs.)
Dimensions

(W x H x D) : 43 mm x 154.5 mm x 191.9 mm

(1-3/4" x 6-1/8" x 7-5/8")

DT-V1900CG MULTI-FORMAT MONITOR

2002 VICTOR COMPANY OF JAPAN, LIMITED

©

28

JVC PROFESSIONAL PRODUCTS COMPANY

DIVISION OF US JVC CORP.

1700 Valley Road Wayne, N.J. 07470

JVC CANADA INC.

21 Finchdene Square, Scarborough Ontario M1X 1A7

Printed in Japan
0202-Y-U-VP