JVC CS-VS601UF2 Instructions Manual

CAR STEREO SPEAKER

For Proper Installation and Use

If a kit is necessary for your car, consult your telephone
directory for the nearest car audio speciality shop ("IN-CAR
ENTERTAINMENT" dealer)

Thank you for purchasing the JVC Car Stereo Speakers. These
speakers can be mounted either in the doors or in the rear tray of
your vehicle. For the secure installation and perfect operation of your
speakers, please read the following carefully.

Specifications

Type : 16 cm (6-1/2") 2-Way Component Speaker, Door/

rear mounting
Power Handling Capacity : 150 watts (MAX. MUSIC POWER)
Impedance : 4 ohms
Magnet Mass : 256 g (9 oz)
Mass : 0.87 kg (2.00 lbs)

(Design and specifications are subject to change without notice.)

INSTRUCTIONS

CS-VS601

CS-VS601

CAR STEREO SPEAKER

1. Before connecting the speakers to the amplifier, confirm that the
power has been turned off. The click noise generated by the
connection if the power is on may damage the speakers.

2. The amplifier and speakers should be connected between
corresponding terminals, i.e. "left" to "left", and "right" to "right", as
well as "+" to "+", and "-" to "-". Connection with reversed polarity
will degrade the quality of stereo reproduction.

3. Do not subject the speakers to excessive input. The power handling
capacity of the CS-VS601 is 150 watts (Max. music power). Any
excessive input may damage the speakers.

4. The CS-VS601 has an impedance of the amplifier's speaker terminal
is rated at 4 ohms.

5. When cleaning the speakers, use a soft cloth and wipe the surface
gently. Do not apply thinner or solvent.

-

UNIT : mm

Dimensions

O1

42

4

-O4

.9

HO

L

ES

O179.3

43.8 21.9

O124

O80

LVT1238-002A

48.8

42.4

O50.5

18.5 9

O49.8

27.3

O58.8

Q/YXFJ105

JVC

(Victor Company of Japan, Limited)

JVC

68

Connection

How to Install

1. To install the speaker in the rear tray, first
determine the appropriate area in which to place
it. The speakers must be installed in a place
where there are spaces of at least 32 mm over
the tray and at least 49 mm under the tray. ln
determining the location, make sure that the
bottom part of each speaker fits into the large
hole in the steel plate on which the rear tray is
fixed.

2. Remove the rear tray.

3. The paper pattern printed on the bottom of the
packing box shows the exact shape of the area
on the rear tray through which the speaker will
be installed. Apply the paper pattern onto the
area determined in 1. above, and trace out the
shape of the area on the tray.

4. Then, cut out the marked area.

5. The next step is to wire the speakers. Be sure to
connect to connect corresponding terminals, i.e.
"left" to "left", "-" to" -", etc.

6. Use the tapping screw and speed nuts provided
to fix the speaker and grille to the rear tray. Match
the 4 screw holes in the speaker frame and the grille
to the holes in the rear tray, insert the 4 screws
in into the holes and secure them with 4 nut.

7. The process for installing the speakers in the
door is much the same as for installing the
speakers in the rear tray. ln this case, however,
extra care must be taken to install the speaker
out of the way of the door handle. lnstall the
speakers with the terminals down.

Amplifier

Woofer

Tweeter

Speed nut

(O4 mm)

x16

Black lined

Black lined

Network cord

x2

Speaker cord

x2

Speaker cord

x2

Amplifier

Midwoofer

Tweeter

2-WAY CROSSOVER NETWORK

12dB/Oct.

WOOFERINPUT TWEETER

2m 2m4m

Screw

x8

(O4x25mm)

Screw

x4

(O4x20mm)

Screw

x4

(O3.5x20mm)

Screw

x2

(O4x25mm)

Screw nut

x4

(O4mm)

1 2

3

4

5

6

7

8 9

7

11

8

9

Parts

10

1

6

x4

x4

Woofer Mounting

Network

x2

Grille Ass'y

10 11

2-WAY CROSSOVER N

ETW

ORK

12

dB/Oct.

WOOFE

R

INPU

T

TWEETER

Mounting bracket

x2

12

Angle adaptor

13

Fix frame

x2 x2

14

2-WAY

CRO

SSOVER NE

TWORK

12dB/

Oct.

WOOFER

INPUT

TWE

ETER

-3dB
0dB

Tweeter level adjust

-3dB
0dB

(-3dB)

-3dB
0dB

(-0dB)

Swivel Mounting

Flush Mounting

13

3

6

14

x2

x2

Tweeter Mounting

Angle Mounting

2-W

AY

C

RO

SS

OVER NETW

ORK

12

dB

/Oct.

W

OOFER

INPUT

TWEETER

11

Network Mounting

2-WAY CR

OSSOVE

R NET

WO

RK

12

dB

/Oct.

WOO

FE

R

INPUT

TWEETER

Surface Mounting

5

4

3

x2

6

x2

14

12

4

5

2

x2

6

x2