JVC CA-UXP55 User Manual

Page 1
MICRO COMPONENT SYSTEM
UX-P55—Consists of CA-UXP55 and SP-UXP55
COMPACT
DIGITAL AUDIO
CD-R/RW PLAYBACK
STANDBY/ON
SLEEP
DISPLAYDIMMER
REPEATRANDOMPROG
AUTO
SOUND
FM MODE
PRESET
MODE
CD
CD
CANCEL MULTI KEY SET
PTY
DISPLAY
/EON
MODE
AHB
VOLUME
PRO
RM-SUXP5R REMOTE CONTROL
STANDBY/ON
STANDBY / ON
AHB PRO
MD/AUX
FM/AM
TAPE
SOUND
PHONES
MICRO COMPONENT SYSTEM UX·P55
CD TAPE FM/AM
/
DIRECT OPERATING
REC
AUTO REVERSE
MD/AUX
CLOCK
VOLUMEFUNCTION
TIMER
REV.MODE
REC
REC
SP-UXP55
CA-UXP55 SP-UXP55
INSTRUCTIONS
For Customer Use:
Enter below the Model No. and Serial No. which are located either on the rear, bot­tom or side of the cabinet. Retain this information for future reference.
Model No. Serial No.
GVT0105-008A
[B]
Page 2
Warnings, Cautions and Others
CAUTION: Invisible laser
radiation when open and interlock failed or defeated. AVOID DIRECT EXPOSURE TO BEAM. (e)
ADVARSEL: Usynlig laser­stråling ved åbning, når sikkerhedsafbrydere er ude af funktion. Undgåudsæt­telse for stråling. (d)
VARO: Avattaessa ja suo­jalukitus ohitettaessa olet alttiina näkymättömälle lasersäteilylle. Älä katso säteeseen. (f)
VARNING: Osynlig laser­strålning när denna del är öppnad och spärren är urkopplad. Betrakta ej strålen. (s)
IMPORTANT for the U.K. DO NOT cut off the mains plug from this equipment. If the plug
fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer.
BE SURE to replace the fuse only with an identical approved type, as originally fitted.
If nonetheless the mains plug is cut off ensure to remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply.
If this product is not supplied fitted with a mains plug then follow the instructions given below:
IMPORTANT: DO NOT make any connection to the terminal which is marked
with the letter E or by the safety earth symbol or coloured green or green-and-yellow.
The wires in the mains lead on this product are coloured in accordance with the following code:
Blue : Neutral Brown : Live
As these colours may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
IF IN DOUBT—CONSULT A COMPETENT ELECTRICIAN.
IMPORTANT FOR LASER PRODUCTS
REPRODUCTION OF LABELS
1 CLASSIFICATION LABEL ON EXTERIOR SURFACE
2 WARNING LABEL INSIDE THE UNIT
1. CLASS 1 LASER PRODUCT
2. CAUTION: Invisible laser radiation when open and interlock failed
or defeated. Avoid direct exposure to beam.
3. CAUTION: Do not open the top cover. There are no user
serviceable parts inside the unit; leave all servicing to qualified service personnel.
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
CAUTION
CAUTION— STANDBY/ON button!
Disconnect the mains plug to shut the power off completely (the STANDBY/ON lamp goes off). The STANDBY/ON button in any position does not disconnect the mains line.
• When the unit is on standby, the STANDBY/ON lamp lights red.
• When the unit is turned on, the STANDBY/ON lamp lights green. The power can be remote controlled.
• Do not block the ventilation openings or holes. (If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.)
• Do not place any naked flame sources, such as lighted candles, on the apparatus.
• When discarding batteries, environmental problems must be considered and local rules or laws governing the disposal of these batteries must be followed strictly.
• Do not expose this apparatus to rain, moisture, dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.
CAUTION: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows: 1 Front:
No obstructions and open spacing.
2 Sides/ Top/ Back:
No obstructions should be placed in the areas shown by the dimensions below.
3 Bottom:
Place on a level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of 10 cm or more.
Front View
15 cm
1 cm15 cm 1 cm 15 cm
Side View
15 cm
15 cm
G-1
10 cm
Page 3
SAFETY INSTRUCTIONS
“SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT”
This equipment has been designed and manufactured to meet international safety standards, but like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured.
✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮
Do read the operating instructions before you attempt to use the equipment.
Do ensure that all electrical connections (including the mains plug, extension leads and interconnections between pieces of equipment) are properly made and in accordance with the manufacturer’s instructions. Switch off and withdraw the mains plug when making or changing connections.
Do consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.
Do be careful with glass panels or doors on equipment.
✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮
DONT continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any wayswitch off, withdraw the mains plug and consult your dealer.
DONT remove any fixed cover as this may expose dangerous voltages.
DONT leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation or has a standby mode. Switch off using the switch on the equipment and make sure that your family know how to do this.
Special arrangements may need to be made for infirm or handicapped people.
DONT use equipment such as personal stereos or radios so that you are distracted from the requirements of traffic safety. It is illegal to watch television whilst driving.
DONT listen to headphones at high volume as such use can permanently damage your hearing.
DONT obstruct the ventilation of the equipment, for example with curtains or soft furnishings.
Overheating will cause damage and shorten the life of the equipment.
DONT use makeshift stands and NEVER fix legs with wood screwsto ensure complete safety always fit the manufacturer’s approved stand or legs with the fixings provided according to the instructions.
DONT allow electrical equipment to be exposed to rain or moisture.
ABOVE ALL
NEVER let anyone, especially children, push anything into holes, slots or any other opening in the casethis
could result in a fatal electrical shock.
NEVER guess or take chances with electrical equipment of any kindit is better to be safe than sorry!
G-2
Page 4
Introduction
We would like to thank you for purchasing one of our JVC products.
Before operating this unit, read this manual carefully and thoroughly to
obtain the best possible performance from your unit, and retain this manual
for future reference.
About This Manual
This manual is organized as follows:
• The manual mainly explains operations using the buttons on the remote control. You can use the buttons both on the remote control and on the unit for the same operations if they have the same or similar names (or marks), unless mentioned otherwise.
• Basic and common information that is the same for many functions is grouped in one place, and is not repeated in each procedure. For instance, we do not repeat the information about turning on/off the unit, setting the volume, changing the sound effects, and others, which are explained in the section “Common Operations” on pages 9 and 10.
• The following marks are used in this manual:
Gives you warning and caution to prevent damage or risk of fire/electric shock. Furthermore, it gives you information about what is not good for obtaining the best possible performance from the unit.
Gives you information and hints you should know.
Power sources
• When unplugging from the wall outlet, always pull the plug, not the AC power cord.
DO NOT handle the AC power cord with wet hands.
Moisture condensation
Moisture may condense on the lens inside the unit in the following cases:
• After starting heating in the room
• In a damp room
• If the unit is brought directly from a cold to a warm place
Should this occur, the unit may malfunction. In this case, leave the unit turned on for a few hours until the moisture evaporates, unplug the AC power cord, and then plug it in again.
Others
• Should any metallic object or liquid fall into the unit, unplug the power cord and consult your dealer before operating any further.
• If you are not going to operate the unit for an extended period of time, unplug the AC power cord from the wall outlet.
Precautions
Installation
• Install in a place which is level, dry and neither too hot nor too cold—between 5˚C and 35˚C.
• Install the unit in a location with adequate ventilation to prevent internal heat buildup in the unit.
• Leave sufficient distance between the unit and the TV.
• Keep the speakers away from the TV to avoid interference with TV.
DO NOT install the unit in a location near heat sources, or in a place subject to direct sunlight, excessive dust or vibration.
DO NOT disassemble the unit since there are no user serviceable parts inside.
If anything goes wrong, unplug the AC power cord and consult your dealer.
– 1 –
Page 5
Contents
Location of the Buttons and Controls....................... 3
Front Panel ................................................................. 3
Remote Control .......................................................... 5
Getting Started............................................................ 6
Supplied Accessories .................................................. 6
Putting the Batteries into the Remote Control ........... 6
Connecting Antennas ................................................. 6
Connecting Speakers .................................................. 7
Connecting Other Equipment..................................... 8
Common Operations .................................................. 9
Turning On the Power ................................................. 9
Setting the Clock ........................................................ 9
Selecting the Sources and Starting Play ....................... 9
Adjusting the Volume ............................................... 10
Selecting the Display Brightness ............................. 10
Reinforcing the Bass Sound ..................................... 10
Selecting the Sound Modes ...................................... 10
Listening to FM and AM (MW/LW) Broadcasts ... 11
Tuning in a Station ................................................... 11
Presetting Stations .................................................... 11
Tuning in a Preset Station ........................................ 11
Playing Back CDs (CD/CD-R/CD-RW).................. 14
Playing Back the Entire CD—Normal Play ............. 14
Basic CD Operations ................................................ 14
Programming the Playing Order of the Tracks
—Program Play .................................................. 15
Playing at Random—Random Play ......................... 16
Repeating Tracks—Repeat Play............................... 16
Prohibiting Disc Ejection—Tray Lock .................... 16
Playing Back Tapes ................................................... 17
Playing Back a Tape ................................................. 17
Recording .................................................................. 18
Recording on a Tape ................................................. 18
CD Direct Recording ................................................. 19
One Track Recording ................................................ 19
Using the Timers ....................................................... 20
Using Daily Timer and Recording Timer................. 20
Using Sleep Timer.................................................... 21
Additional Information ............................................ 22
Troubleshooting ........................................................ 22
Receiving FM Stations with RDS ............................ 12
Changing the RDS Information ............................... 12
Searching for Programs by PTY Codes
(PTY Search) ...................................................... 12
Switching to a Program Type of Your
Choice Temporarily ............................................ 13
Maintenance .............................................................. 23
Specifications............................................................. 24
– 2 –
Page 6
Location of the Buttons and Controls
Become familiar with the buttons and controls on your unit.
Front Panel
Front Panel
1
2
3
4 5
6
7
8
STANDBY/ON
AHB PRO
SOUND
STANDBY/ON
COMPACT
DIGITAL AUDIO
MICRO COMPONENT SYSTEM UX-P55
CD TAPE FM/AM
/
DIRECT OPERATING
FUNCTION
CD-R/RW PLAYBACK
MD/AUX
VOLUME
q
w
e
r
CLOCK
t
y
TIMER
u
i o
;
9
p
PHONES
REC
AUTO REVERSE
– 3 –
REV.MODE
a s
REC
d
f
Page 7
Display Window
Continued
1
[
DAILY REC SLEEP
2
CLOCK PRGM
5
See pages in the parentheses for details.
Front Panel
1 Remote sensor 2 STANDBY/ON lamp (9) 3 (STANDBY/ON) button (9, 16, 21) 4 TAPE 2 3 button (9, 17, 18)
Pressing this button also turns on the unit.
5 CD 3/8 (play/pause) button (9, 14, 19)
Pressing this button also turns on the unit.
6 AHB (Active Hyper Bass) PRO button (10) 7 SOUND button (10) 8 MD/AUX button (9)
Pressing this button also turns on the unit.
9 PHONES jack (10) p Tape operation lamps (17, 18)
2 3 (tape direction) and REC lamps
q 0 (disc tray open/close) button (14)
Pressing this button also turns on the unit.
w Disc tray e FM/AM button (9, 11)
Pressing this button also turns on the unit.
r Display window t CLOCK button (9) y VOLUME + / – control (10) u TIMER button (20, 21) i ¢ (forward search) button (9, 11, 14, 16, 17, 20) o 7 (stop) button (14 – 19) ; 4 (reverse search) button (9, 11, 14, 17, 20) a REV.MODE (reverse mode) button (17 – 19) s Cassette holder d REC button (18, 19) f 0 (eject) button for cassette deck (17 – 19)
RANDOM
6
3
]
REC RDSEON
4
TA NEWS INFO
ALL BASS SOUND MONO ST
7
Display Window
1 Tape operation indicators
2 3 (tape direction) and (reverse mode)
indicators
2 Timer indicators
(timer), DAILY, REC and SLEEP indicators
3 REC indicator 4 RDS operation indicators
• RDS, EON, and TA/NEWS/INFO indicators
5 CLOCK indicator 6 CD play mode indicators
• PRGM (program), RANDOM, and repeat ( / ALL) indicators
7 BASS (Active Hyper Bass) indicator 8 SOUND (sound mode) indicator 9 Tuner operation indicators
• MONO and ST (stereo) indicators
p Main display
• Shows the source name, frequency, etc.
8
STANDBY
MICRO COMPONENT SYSTEM UX-P55
STANDBY / ON
AHB PRO
DIRECT OPERATING
SOUND
PHONES
9p
COMPACT
DIGITAL AUDIO
CD-R/RW PLAYBACK
CLOCK
VOLUMEFUNCTION
TIMER
REV.MODE
REC
– 4 –
When using the remote control, point it at the remote sensor on the front panel.
Page 8
Remote Control
1
2 3 4 5
6 7 8
9
p q
w
e
r
SOUND
CANCEL MULTI KEY SET
DISPLAY
MODE
CD
MODE
AHB PRO
DISPLAYDIMMER
AUTO
PRESET
PTY
/EON
CD
VOLUME
SLEEP
REPEATRANDOMPROG
FM MODE
STANDBY/ON
MD/AUX
FM/AM
TAPE
t
y
u
i
o ;
a
s d
f
1 REPEAT button (16) 2 DIMMER button (10) 3 DISPLAY button (9) 4 PROG (program) button (15) 5 RANDOM button (16) 6 SOUND MODE button (10) 7 AUTO PRESET button (11) 8 CD 0 (disc tray open/close) button (14)
Pressing this button also turns on the unit.
9 CD 3/8 button (9, 14, 15)
Pressing this button also turns on the unit.
p 4 (reverse search) button (11 – 14, 17) q 7 (stop) button (14 – 19) w CANCEL button (15) e RDS operation buttons (12, 13)
• DISPLAY MODE and PTY/EON buttons
r AHB (Active Hyper Bass) PRO button (10) t (STANDBY/ON) button (9) y SLEEP button (21) u MD/AUX button (9)
Pressing this button also turns on the unit.
i FM/AM button (9, 11)
Pressing this button also turns on the unit.
o TAPE 2 3 button (9, 17)
Pressing this button also turns on the unit.
; FM MODE button (11) a ¢ (forward search) button (11 – 14, 16, 17) s SET button (11, 15) d MULTI KEY > / < buttons (11, 14 – 16) f VOLUME + / – buttons (10)
RM-SUXP5R REMOTE CONTROL
– 5 –
Page 9
Getting Started
Continued
Supplied Accessories
Make sure that you have all the following items. The number in the parentheses indicates the quantity of the pieces supplied.
• AM loop antenna (1)
• FM antenna (1)
• Remote control (1)
• Batteries (2)
If anything is missing, consult your dealer immediately.
Putting the Batteries into the Remote Control
Insert the batteries—R6(SUM-3)/AA(15F)—into the remote control, by matching the polarity (+ and –) on the batteries with the + and – markings on the battery compartment. When the remote control can no longer operate the unit, replace both batteries at the same time.
1
Connecting Antennas
FM antenna
ANTENNA
AM EXT
AM LOOP
FM 75
COAXIAL
FM antenna (supplied)
1 Attach the FM antenna to the FM 75
COAXIAL terminal.
2 Extend the FM antenna. 3 Fasten it up in the position which gives you
the best reception, then fix it on the wall, etc.
R6(SUM-3)/AA(15F)
2
3
• DO NOT use an old battery together with a new one.
• DO NOT use different types of batteries together.
• DO NOT expose batteries to heat or flame.
• DO NOT leave the batteries in the battery compartment when you are not going to use the remote control for an extended period of time. Otherwise, it will be damaged from battery leakage.
About the supplied FM antenna
The FM antenna supplied with this unit can be used as temporary measure. If reception is poor, you can connect an outdoor FM antenna.
To connect an outdoor FM antenna
Before connecting it, disconnect the supplied FM antenna.
Outdoor FM antenna (not supplied)
Coaxial cable
ANTENNA
AM EXT
AM LOOP
FM 75 COAXIAL
A 75 antenna with coaxial type connector (IEC or DIN
45325) should be used.
– 6 –
Page 10
AM (MW/LW) antenna
Connecting Speakers
]
ANTENNA
1
2
AM loop antenna (supplied)
AM EXT
AM LOOP
FM
COAXIAL
]
1
Vinyl-covered wire (not supplied)
RIGHT LEFT
Speaker cord
75
Right
speaker
SPEAKER IMPEDANCE MIN
6
Black
2
Red
MAIN SPEAKERS
speaker
3
Speaker cord
Left
1 Connect the AM loop antenna to the AM
LOOP terminals as illustrated.
2 Turn the AM loop antenna until you have the
best reception.
To connect an outdoor AM (MW/LW) antenna
When reception is poor, connect a single vinyl-covered wire to the AM EXT terminal and extend it horizontally. (The AM loop antenna must remain connected.)
For better reception of both FM and AM (MW/LW)
• Make sure the antenna conductors do not touch any other terminals and connecting cords.
• Keep the antennas away from metallic parts of the unit, connecting cords, and the AC power cord.
1 Press and hold the clamp of the speaker
terminal on the rear of the unit.
2 Insert the end of the speaker cord into the
terminal.
Match the polarity of the speaker terminals: Red (+) to red (+) and black (–) to black (–).
• If the cords are covered with insulation, remove a short section of insulation at the end of each cord by twisting and pulling it off.
3 Release the finger from the clamp.
• DO NOT connect speakers while the power is on.
• DO NOT connect more than one speaker to each speaker teminal.
IMPORTANT: Use only speakers with the same speaker impedance as indicated by the speaker terminals on the rear of the unit.
– 7 –
Page 11
To remove the speaker grilles
The speaker grilles are removed as the illustrations below.
Holes Projections
Speaker grille
To connect audio equipment with an optical digital input terminal
You can record CD sound onto the connected digital equipment.
Protective plug
OPTICAL DIGITAL OUT
Before connecting the other equipment, remove the protective plug from the terminal.
To remove the speaker grille, inserting your fingers at the top of the speaker grille, pull towards you. Then pull the bottom towards you.
To attach the speaker grille, put the projections of the speaker grille into the holes of the speaker.
Connecting Other Equipment
You can connect both of the analog and digital equipment.
DO NOT connect any equipment while the power is on.
DO NOT plug in any equipment until all connections are complete.
To connect audio equipment
Be sure that the plugs of the audio cords are colored: White plugs and jacks are for left audio signals, and red ones for right audio signals.
AUX
RL
OUT
IN
Audio equipment with an optical digital input
To optical digital input
Connect an optical digital cord (not supplied) between the optical digital input terminal on the other equipment and the OPTICAL DIGITAL OUT terminal.
Now, you can plug the AC power cord.
IMPORTANT: Be sure to check all connections to be done before plugging the AC power cord into a wall outlet.
To audio output
To audio input
Audio equipment
By using audio cords (not supplied), connect:
• Between the audio input jacks on the other equipment and AUX OUT jacks: For recording on the other equipment.
• Between the audio output jacks on the other equipment and AUX IN jacks: For playing the other equipment.
8
Page 12
Common Operations
Turning On the Power
When you press the play button—CD 3/8, TAPE 2 3, or the source selecting button—FM/AM and MD/AUX, the unit automatically turns on and starts playback if the source is ready.
To turn on the unit, press (STANDBY/ON). The STANDBY/ON lamp on the unit lights green.
STANDBY/ON
STANDBY/ON
STANDBY/ON
To turn off the unit (on standby), press (STANDBY/ ON) again. The STANDBY/ON lamp lights red.
• The CLOCK indicator flashes on the display until you set the built-in clock. After setting the clock, the clock time will appear on the display while the power is off.
• A little power is always consumed even while the unit is on standby.
To switch off the power supply completely, unplug the AC power cord from the AC outlet.
When you unplug the AC power cord or if a power failure occurs
The clock is reset to “0:00” right away, while the tuner preset stations (see page 11) will be erased in a few days.
Setting the Clock
Before operating the unit any further, first set the clock built in this unit. When you plug the AC power cord into the wall outlet, the CLOCK indicator starts flashing on the display. You can set the clock whether the unit is on or off.
• There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
On the unit ONLY:
1
Press CLOCK for more than 2 seconds.
The hour digits start flashing on the display.
CLOCK
2
Press ¢ or 4 to adjust the hour, then press CLOCK.
The minute digits start flashing on the display.
CLOCK
CLOCK
3
Press ¢ or 4 to adjust the minute, then press CLOCK.
The CLOCK indicator remains lit on the display.
CLOCK
CLOCK
To check the clock time
Press DISPLAY on the remote control (or CLOCK on the unit) while playing any source.
• Each time you press the button, the source indication and the clock time alternate on the display.
• When you unplug the AC power cord or if a power failure occurs, the clock loses the setting and is reset to “0:00.” You need to set the clock again.
• The clock may gain or lose 1 to 2 minutes per month.
DISPLAY
CLOCK
Selecting the Sources and Starting Play
To play back CDs, press CD 3/8. (See pages 14 – 16.) To play back tapes, press TAPE 2 3. (See page 17.) To listen to the FM/AM (MW/LW) broadcasts,
press FM/AM. (See pages 11 – 13.)
To select the external equipment as the source,
press MD/AUX.
CD
TAP E
FM/AM
MD/AUX
CLOCK
9
Page 13
Adjusting the Volume
Reinforcing the Bass Sound
You can adjust the volume level only while the unit is turned on. The volume level can be adjusted between “VOLUME 0” and “VOLUME 40.”
VOLUME
When using the remote control, press
+
VOLUME + to increase the volume or press VOLUME – to decrease it.
When using the unit, turn VOLUME + / – clockwise (+) to increase the volume or counterclockwise (–) to decrease it.
VOLUME
For private listening
Connect a pair of headphones to the PHONES jack. No sound comes out of the speakers. Be sure to turn down the volume before connecting or putting on headphones.
DO NOT turn off (on standby) the unit with the volume set to an extremely high level; otherwise, a sudden blast of sound can damage your hearing, speakers and/or headphones when you turn on the unit or start playing any source next time. REMEMBER you cannot adjust the volume level while the unit is on standby.
You can reinforce the bass sound to maintain rich (“AHB 1” and “AHB 2”), full bass at low volume. This function only affects the playback sound, but does not affect your recording.
To get the effect, press AHB (Active Hyper
AHB PRO
Bass) PRO until “AHB 1” or “AHB 2” appears on the display. The BASS indicator also lights up on the display.
BASS
• Each time you press the button, the bass sound change as follows:
AHB 1
AHB OFF
(Canceled)
AHB 2
“AHB 2” has much more bass reinforcement effect than “AHB 1.”
To cancel the effect, press AHB PRO until “AHB OFF” appears on the display. The BASS indicator goes off.
Selecting the Sound Modes
You can select one of the 4 preset sound modes. This function only affects the playback sound, but does not affect your recording.
Selecting the Display Brightness
You can change the display brightness only while the unit is turned on.
To change the display brightness, press DIMMER on the remote control.
• Each time you press the button, the display dims and brightens alternately.
DIMMER
To select the sound modes, press
SOUND
MODE
SOUND MODE on the remote control (or SOUND on the unit) until the sound mode you want appears on the display. The SOUND indicator also lights up on the display.
SOUND
SOUND
• Each time you press the button, the sound modes change as follows:
ROCK POP
FLAT
(Canceled)
CLASSICJAZZ
ROCK: Gives a heavy sound. Boosts low and high
frequency.
POP: Good for vocal music. CLASSIC: Good for classical music. JAZZ: Gives a feeling of live atmosphere. Good for
acoustic music.
FLAT: The sound mode is canceled. The SOUND
indicator goes off.
10
Page 14
Listening to FM and AM (MW/LW) Broadcasts
Tuning in a Station
1
Press FM/AM.
The unit automatically turns on and tunes in the previously tuned station (either FM or AM—MW/LW).
• Each time you press the button, the band alternates between FM and AM (MW/LW).
2
Press and hold ¢ or 4 for more than 1 second.
The unit starts searching for stations and stops when a station of sufficient signal strength is tuned in. If a program is broadcasted in stereo, the ST (stereo) indicator lights up.
To stop searching, press ¢ or 4.
When you press ¢ or 4 briefly and repeatedly
The frequency changes step by step.
To change the FM reception mode
When an FM stereo broadcast is hard to receive or noisy, press FM MODE on the remote control so that the MONO indicator lights up on the display. Reception improves.
To restore the stereo effect, press FM MODE again so that the MONO indicator goes off. In this stereo mode, you can hear stereo sounds when a program is broadcasted.
FM/AM
FM MODE
3
Repeat steps 1 and 2 to store stations for the other band.
When you cannot automatically store stations you want
Stations with weak signals cannot be detected with this automatic presetting. To store such a station, use the manual presetting.
To preset stations manually—Manual Presetting
• There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 2 again.
On the remote control ONLY:
1
Tune in the station you want to preset.
• See “Tuning in a Station.”
2
Press SET.
3
Press MULTI KEY > or
SET
MULTI KEY
MULTI KEY < to select a preset number.
4
Press SET again.
SET
Presetting Stations
You can preset 30 FM and 15 AM (MW/LW) stations— using either automatic presetting or manual presetting. In some cases, test frequencies have been already memorized for the tuner since the factory examined the tuner preset function before shipment. This is not a malfunction. You can preset the stations you want into memory by following the presetting method.
To preset stations automatically—Automatic Presetting
You need to preset stations separately for the FM and AM (MW/LW) bands.
On the remote control ONLY:
1
Press FM/AM to select the band.
• Each time you press the button, the band alternates between FM and AM (MW/LW).
2
Press and hold AUTO PRESET for more than 2 seconds.
Local stations with strong signals are searched and stored in memory automatically. When automatic presetting is over, the station stored in preset number 1 is received.
FM/AM
AUTO
PRESET
The tuned station in step 1 is stored in the preset number selected in step 3.
• Storing a new station on a used number erases the previously stored one.
When you unplug the AC power cord or if a power failure occurs
The preset stations will be erased in a few days. If this happens, preset the stations again.
Tuning in a Preset Station
On the remote control ONLY:
1
Press FM/AM.
The unit automatically turns on and tunes in the previously tuned station (either FM or AM—MW/LW).
• Each time you press the button, the band alternates between FM and AM (MW/LW).
2
Press MULTI KEY > or MULTI KEY < to select a preset number.
FM/AM
MULTI KEY
11
Page 15
Receiving FM Stations with RDS
Continued
RDS (Radio Data System) allows FM stations to send an additional signal along with their regular program signals. For example, the stations send their station names, as well as information about what type of program they broadcast, such as sports or music, etc. When tuned to an FM station which provides the RDS service, the RDS indicator lights up on the display. With the unit, you can receive the following types of RDS signals.
PS (Program Service):
Shows commonly known station names.
PTY (Program Type):
Shows types of broadcast programs.
RT (Radio Text):
Shows text messages the station sends.
Enhanced Other Networks:
Provides the information about the types of the programs sent by other RDS stations.
More about RDS
• Some FM stations do not provide RDS signals.
• RDS services vary among FM RDS stations. For details on RDS services in your area, check with local radio stations.
• RDS may not work correctly if the received station is not transmitting the signals properly or if the signal strength is weak.
Changing the RDS Information
Searching for Programs by PTY Codes (PTY Search)
One of the advantages of RDS is that you can locate a particular kind of program by specifying the PTY codes.
• For details on the PTY codes, see “Additional Information” on page 22.
To search for a program using the PTY codes
REMEMBER you must preset FM RDS stations to use the PTY codes. If not yet done, see page 11.
• There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
On the remote control ONLY:
PTY
1
Press PTY/EON until “PTY” and “SELECT” alternately appear on the display.
• Each time you press the button, RDS operation mode changes as follows:
PTY SELECT EON SELECT
2
Press ¢ or 4 until the
(See page 13.)
Canceled
PTY code you want appears on the display.
• Each time you press the button, the PTY codes change as follows:
/EON
You can see RDS information on the display while listening to an FM station.
On the remote control ONLY:
DISPLAY
Press DISPLAY MODE.
• Each time you press the button, the display changes to show the following information:
PS
(Program Service)
(or preset channel no.)
• If no PS, PTY, or RT signals are sent by a station
“NO PS,” “NO PTY,” or “NO RT” appears on the display.
• On the characters displayed
When the display shows PS, PTY or RT signals: —The display shows upper case letters only. —The display cannot show accented letters; For example, “A”
may represent accented “A’s” like “Á, Â, Ã, À, Ä and Å.”
PTY
(Program Type)RT(Radio Text)
Station frequency
MODE
NEWS AFFAIRS INFO SPORT EDUCATE DRAMA CULTURE SCIENCE VARIED POP M ROCK M EASY M LIGHT M CLASSICS OTHER M WEATHER FINANCE CHILDREN SOCIAL RELIGION PHONE IN TRAVEL “ LEISURE “ JAZZ “ COUNTRY NATION M OLDIES FOLK M DOCUMENT TRAFFIC (back to the beginning)
3
Press PTY/EON once again.
While searching, “SEARCH” and the selected PTY code alternately appear on the display. The unit searches 30 preset FM stations, stops when it finds the one you have selected (“FOUND” appears), and tunes in that station.
• If no program is found, “NOTFOUND” appears on the display and the unit returns to the last received station.
To stop searching any time during the process
Press PTY/EON while searching.
PTY
/EON
12
Page 16
Switching Temporarily to a Program Type of Your Choice
How the Enhanced Other Networks function actually works:
The Enhanced Other Networks function allows the unit to switch temporarily to a broadcast program of your choice (TA, NEWS, and INFO) from a different station.
• The function only works when you are listening to a preset FM RDS stations providing the data.
To activate the Enhanced Other Networks function
REMEMBER you must preset FM RDS stations to use the function. If not yet done, see page 11.
• There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
On the remote control ONLY:
PTY
1
Press PTY/EON until “EON” and
/EON
“SELECT” alternately appear on the display.
• Each time you press the button, RDS operation mode changes as follows:
PTY SELECT
(See page 12.)
2
Press ¢ or 4 until the
EON SELECT
Canceled
data type you want appears on the display.
The selected data type indicator (TA, NEWS, and INFO) also flashes.
TA
RDSEON
• Each time you press the button, the data type indication changes as follows:
TA NEWS INFO
OFF
(Canceled)
TA: Traffic announcement NEWS: News INFO: Program the purpose of which is to impart
advice in the widest sense.
OFF: The function is canceled. The data type
indicator (TA, NEWS, and INFO) goes off.
3
Press PTY/EON once again.
The data type indicator stops flashing and remains lit. Now, the function is activated. See “How the Enhanced Other Networks function actually works.”
PTY
/EON
CASE 1 If there is no station broadcasting the program you
have selected
The unit continues tuning in the current station.
«
When a station starts broadcasting the program you have selected, the unit automatically switches to the station. The indicator of received PTY code starts flashing.
«
When the program is over, the unit goes back to the previously tuned station, but the function still remains activated.
CASE 2 If there is a station broadcasting the program you have
selected
The unit tunes in the program. The indicator of received PTY code starts flashing.
«
When the program is over, the unit goes back to the previously tuned station, but the function still remains activated.
CASE 3 If the FM station you are listening to is broadcasting
the program you have selected
The unit continues to receive the station but the indicator of received PTY code starts flashing.
«
When the program is over, the indicator of received PTY code stops flashing and remains lit, but the function still remains activated.
More about the Enhanced Other Networks function
• The data sent from some stations may not be compatible with this unit and also some stations may not include Enhanced Other Networks data. In this case, the function may not work correctly.
• While listening to a program tuned into by the function, the station does not change even if another network station starts broadcasting a program of the same data.
• The function is canceled when you change the source to CD, TAPE or AUX, while it is temporarily canceled when you change the source to AM (MW).
• This function is also canceled when you turn off the unit.
13
Page 17
Playing Back CDs (CD/CD-R/CD-RW)
Continued
This unit has been designed to playback the following CDs:
•CD
• CD-R
• CD-RW
Continued use of irregular shape CDs (heart-shape, octagonal, etc.) can damage the unit.
General Notes
In general, you will have the best performance by keeping your CDs and the mechanism clean.
• Store CDs in their cases, and keep them in cabinets or on shelves.
• Keep the unit’s disc tray closed when not in use.
When playing a CD-R or CD-RW
User-edited CD-Rs (CD-Recordable) and CD-RWs (CD-ReWritable) can be played back only if they are already “finalized”.
• You can play back your original CD-Rs or CD-RWs recorded in music CD format. (However, they may not be played back depending on their characteristics or recording conditions.)
• Before playing back CD-Rs or CD-RWs, read their instructions or cautions carefully.
• Some CD-Rs or CD-RWs may not be played back on this unit because of their disc characteristics, damage or stain on them, or if the player’s lens is dirty.
• CD-RWs may require a longer readout time. (This is caused by the fact that the reflectance of CD-RWs is lower than for regular CDs.)
3
Press CD 3/8.
The disc tray automatically closes and the first track of the CD starts playing.
Track number
• The CD automatically stops when the last track of the CD has finished playing.
To stop playing, press 7.
Total track number
To remove the disc, press CD 0 on the remote control (or 0 on the CD player section).
• If the CD cannot be read correctly (because it is scratched, for example)
“00 0000” appears on the display.
• If no CD is inserted
“NO DISC” appears on the display.
• If a unreadable CD-R or CD-RW is inserted
“BLANK CD” appears on the display.
DO NOT try to open or close the CD tray by hand as it will be damaged.
Elapsed playing time
Total playing time
CD
Playing Back the Entire CD—Normal Play
1
Press CD 0 on the remote control (or 0 on the CD player section).
The unit automatically turns on and the disc tray comes out.
2
Place a disc correctly on the circle of the disc tray, with its label side up.
CORRECT INCORRECT
• When using a CD single (8 cm), place it on the inner circle of the disc tray.
Basic CD Operations
While playing a CD, you can do the following operations.
CD
To stop play for a moment
Press CD 3/8. While pausing, the elapsed playing time flashes on the display.
To resume playing, press CD 3/8 again.
To go to another track
Press MULTI KEY > / MULTI KEY < or ¢ / 4 repeatedly before or during playback.
• MULTI KEY > or ¢ :
Skips to the beginning of the next or succeeding tracks.
• MULTI KEY < or 4 :
Goes back to the beginning of the current or previous tracks.
To locate a particular point in a track
During play, press and hold ¢ or 4.
¢ : Fast-forwards the tracks.
4 : Fast-reverses the tracks.
CD
MULTI KEY
– 14 –
Page 18
Programming the Playing Order of the Tracks Program Play
You can arrange the order in which tracks play before you start playing. You can program up to 20 tracks.
To check the program contents
You can check the program contents by pressing PROG on the remote control. The programed tracks are shown in the programed order.
PROG
On the remote control ONLY:
1
Load a CD.
If the current playing source is not the CD player, press CD 3/8, then 7 before going to the next step.
2
Press PROG (program).
The PRGM (program) indicator lights up on the display.
PRGM
If a program has been stored in memory, the program is called up.
3
Press MULTI KEY > or MULTI KEY < to select the track number, then press SET.
MULTI KEY
SET
PROG
To modify the program
Before or after playing, you can erase the last programed track by pressing CANCEL on the remote control.
Each time you press the button, the last programed track is erased from the program.
To add tracks in the program before playing, simply select the track numbers you want to add by following step 3 of the programming procedure.
If you try to program the 21st track
FULL will appear on the display.
If the total playing time is 100 minutes or more
The total playing time will not be shown. “– –:– –” will appear.
CANCEL
PRGM
Program step numberTrack number
4
Repeat step 3 to program other tracks you want.
5
Press CD 3/8.
The tracks are played in the order you have programed.
To stop playing, press 7.
To exit from Program play mode, press 7 before or after
playing. The PRGM (program) indicator goes off. All the programed tracks will be cleared.
Disc ejection also erases the program.
CD
15
Page 19
Playing at RandomRandom Play
Prohibiting Disc Ejection—Tray Lock
The tracks will play in no particular order when you use this mode.
On the remote control ONLY:
To use Random play mode, press RANDOM
before or during playing. The RANDOM indicator lights up on the display.
RANDOM
The tracks are played at random. Random play ends when all the tracks are played once.
To skip the current track, press ¢ or MULTI KEY >.
You cannot go back to the previous track by pressing 4
or MULTI KEY <.
To stop playing, press 7.
Random play mode is also canceled. To exit from Random play mode, press RANDOM again
before or during playing. Random play mode is canceled and Normal play resumes.
RANDOM
You can lock the disc tray and prohibit to eject the CD.
This is possible only while the unit is turned on.
On the unit ONLY:
To prohibit disc ejection, press
(STANDBY/ON) while holding 7. (If the disc tray is opened, close it first.) LOCKED appears for a while, and the disc tray is locked.
To cancel the prohibition and unlock the CD, press (STANDBY/ON) while
holding 7. UNLOCKED appears for a while, and the disc tray is unlocked.
If you try to eject the CD,
LOCKED appears to inform you that the disc tray is locked.
STANDBY/ON
STANDBY/ON
Repeating TracksRepeat Play
You can have all the tracks, the program or individual track currently playing to repeat as many times as you like.
On the remote control ONLY:
To repeat playing, press REPEAT before or
during playing.
Each time you press the button, Repeat play mode changes as follows, and the following indicator lights up on the display:
ALL
Canceled
: Repeats one track. : In Normal play mode, repeat all the tracks.
ALL
In Program play mode, repeat all the tracks in the program. In Random play mode, repeats all the tracks in random order.
To stop playing, press 7. To cancel Repeat play, press REPEAT repeatedly until the
repeat indicator goes off from the display.
In Random play cannot be selected. If is selected when you press RANDOM, it is canceled (goes off.)
Repeat mode remains in effect even when you change the play mode.
REPEAT
16
Page 20
Playing Back Tapes
You can play back type I, type II, and type IV tapes without changing any settings.
Playing Back a Tape
1
Press 0 for cassette deck.
2
Put a cassette in with the exposed part of the tape down.
To stop playing, press 7. To fast-wind to the left or to the right, press ¢ or 4
while the tape is not running. The tape direction indicator (2 or 3) starts flashing quickly on the display.
To remove the cassette, press 0 for cassette deck.
To play both sidesReverse Mode
You can set the deck to play just one side of a tape, both sides once, or both sides continuously.
Press REV.MODE on the unit.
Each time you press the button, reverse mode changes as follows:
: The deck automatically stops after playing both
sides of the tape. (Stops when playback in the 2 direction is finished.)
: The deck continues to play both sides of the
tape until 7 is pressed.
: The deck automatically stops after playing one
side of the tape.
REV.MODE
3
Close the cassette holder gently.
4
Press TAPE 2 3.
The unit automatically turns on and the tape play starts. The tape direction indicator (3 or 2) flashes slowly on the display.
Each time you press the button, the tape direction changes.
3 : plays the front side. 2 : plays the reverse side.
The tape direction lamp on the unit starts flashing to indicate the tape running direction.
REC
The use of the C-120 or thinner tape is not recommended, since characteristic deterioration may occur and this tape easily jams in the pinch­rollers and the capstans.
TAPE
When the tape plays to the end, the deck automatically stops if the reverse mode is set to or . (See To play both sidesReverse Mode.”)
17
Page 21
Recording
Continued
IMPORTANT:
• It should be noted that it may be unlawful to re-record pre-recorded tapes, records, or discs without the consent of the owner of copyright in the sound or video recording, broadcast or cable programme and in any literary, dramatic, musical, or artistic embodied therein.
• The recording level is automatically set correctly, so it is not affected by the VOLUME, AHB (Active Hyper Bass) PRO, and SOUND MODE settings. Thus, during recording you can adjust the sound you are actually listening to without affecting the recording level.
• If recordings you have made have excessive noise or static, the unit may be too close to a TV. Increase the distance between the TV and the unit.
• You can use type I tape for recording.
To protect your recording
Cassettes have two small tabs on the back to protect from unexpected erasure or re-recording. To protect your recording, remove these tabs. To re-record on a protected tape, cover the holes with adhesive tape.
To keep the best recording and playback sound quality
If the heads, capstans, and pinch rollers of the cassette decks become dirty, the following will occur:
• Impaired sound quality
• Discontinuous sound
• Fading
• Incomplete erasure
• Difficulty in recording
Recording on a Tape
On the unit ONLY:
1
Put a recordable cassette in with the exposed part of the tape down.
2
Close the cassette holder gently.
• If you want to record on both sides of a tape, see “To record on both sides—Reverse Mode.”
3
Check the recording direction for the tape.
• If the tape direction is not correct, press TAPE 2 3 twice then 7 to change the tape direction.
4
Start playing the source—FM, AM or auxiliary equipment connected to AUX jacks.
• When the source is CD, see “CD Direct Recording” on page 19.
5
Press REC.
The REC indicator lights up on the display and recording starts.
• The REC lamp on the unit also lights red.
REC
REC
To clean the heads, capstans, and pinch rollers
Use a cotton swab moistened with alcohol.
Capstans
Heads
Pinch rollers
To demagnetize the heads
Turn off the unit, and use a head demagnetizer (available at electronics and audio shops).
At the start and end of cassette tapes
There is leader tape which cannot be recorded onto. Thus, when recording CDs or radio broadcasts, wind the leader tape first to ensure that the recording will be made without any music part lost.
To stop recording, press 7. To remove the cassette, press 0 for cassette deck.
To record on both sides—Reverse Mode
Press REV.MODE on the unit until the indicator is lit.
• When using the reverse mode for recording,
start recording in the forward (3) direction first. Otherwise, recording will stop when recording is done only on one side (reverse) of the tape.
REV.MODE
– 18 –
Page 22
CD Direct Recording
One Track Recording
Everything on the CD goes onto the tape in the same order as it is on the CD, or according to the order you have made for Program play.
On the unit ONLY:
1
Put a recordable cassette in with the exposed part of the tape down.
2
Place a disc correctly on the circle of the disc tray, with its label side up.
If the current playing source is not the CD player, press
CD 3/8, then 7 before going to the next step.
If you want to record on both sides of a tape, see To record on both sidesReverse Mode.
If you do not want pauses of about 4 seconds recorded between selections, press CD 3/8 twice. If nothing is done, non-recorded pause will be automatically recorded between selections.
This recording method is convenient when you record tracks while playing a CD. You can only record your favorite songs on the tape.
On the unit ONLY:
1
Put a recordable cassette in with the exposed part of the tape down.
2
Play the track on the CD you wish to record.
3
Press REC.
The CD player returns to the beginning of that track and the track is recorded on the tape. After recording, the CD player and cassette deck automatically stop.
4
Repeat steps 2 and 3 to record other tracks
REC
you want.
3
Press REC.
The REC indicator lights up on the display and recording starts. After recording, the CD player and cassette deck automatically stop.
To stop CD Direct Recording, press 7. The tape stops after 4 seconds.
To remove the cassette, press 0 for the cassette deck.
To record on both sides—Reverse Mode
Press REV.MODE on the unit until the indicator is lit.
When using the reverse mode for CD Direct
Recording, start recording in the forward (3) direction first. When the tape reaches its end while recording a song in the forward direction (3), the last song will be re-recorded at the beginning of the reverse side (2). If you start recording on the reverse side (2), recording will stop when recording is done only on one side (reverse) of the tape.
When making SLEEP timer settings while doing CD Direct recording
Set enough time to allow for the CD to finish playing; otherwise the power will go off before recording is completed.
REC
REV.MODE
19
Page 23
Using the Timers
Continued
There are three timers availableDaily Timer, Recording Timer, and Sleep Timer.
Before using the timers, you need to set the clock built in the unit (see page 9). When you press TIMER on the unit for more than 3 seconds, the display alternates between ADJUST and CLOCK for about 5 seconds.
Using Daily Timer and Recording Timer
You can set the timer whether the unit is on or off.
When the on-time comes, the unit automatically turns on (the
indicator flashes just before the on-time, and continues flashing while the timer is operating). Then, when the off­time comes, the unit automatically turns off (on standby). The timer setting remains in memory until you change it.
When the DAILY indicator is lit on the display, the timer
acts as the Daily Timer. Once the Daily Timer has been set, it will be activated at the same time everyday until the timer is turned off.
When the REC indicator is lit on the display, the timer acts
as the Recording Timer. After the Recording Timer has been performed, the details of the setting remain stored but the timer is turned off.
Before you start...
When using TUNER as the source to play, make sure to select the desired station before turning off the power.
There is a time limit in doing the following steps. If the
setting is canceled before you finish, start from step 1 again.
On the unit ONLY:
1
Press and hold TIMER for more than 3 seconds.
The timer ( ) indicator lights up, and the timer mode indicator (DAILY or REC) and the current on-time flash on the display. The unit enters on-time setting mode.
TIMER
2
Set the on-time you want the unit to turn on at.
1) Press ¢ or 4 to set the hour, then
press TIMER.
2) Press ¢ or 4 to set the minute,
then press TIMER. The unit enters off-time setting mode.
[
DAILY
3
Set the off-time you want
]
the unit to turn off (on standby) at.
1) Press ¢ or 4 to set the hour, then
press TIMER.
2) Press ¢ or 4 to set the minute,
then press TIMER. The unit enters source selecting mode.
4
Press ¢ or 4 to select the timer mode (Daily Timer or Recording Timer) and the source to play, then press TIMER.
Each time you press ¢ or 4, the
timer mode and the source change as follows:
DAILY
TUNER
DAILY
TAPE
DAILY
TUNER: tunes into the last station you were
listening to. (Daily Timer)
REC
TUNER: records the last station you were listening
to. (Recording Timer)
Put a recordable cassette into the deck.
DAILY
CD: plays a CD. (Daily Timer)
DAILY
TAPE: plays a tape. (Daily Timer)
Make sure that the tape direction is correct.
REC
TUNER
DAILY
CD
TIMER
TIMER
TIMER
[
DAILY
5
]
Press ¢ or 4 to set the volume level.
You can select the volume level (VOLUME 0 to VOLUME 40 and VOLUME –”). If you select VOLUME –,” the volume is set to the last level when the unit has been turned off.
To turn off the volume while the Recording Timer
REC
(
TUNER) is working, set the volume level
VOLUME 0.”
20
Page 24
6
Press TIMER to complete the timer
TIMER
setting.
7
Press (STANDBY/ON) to turn
STANDBY/ON
off the unit (on standby) if you have set the timer with the unit
STANDBY/ON
turned on.
When the timer turns on the unit, the timer ( ) indicator and the selected timer mode indicator (DAILY or REC) start flashing.
To cancel the setting, press and hold TIMER until the timer ( ) indicator goes off from the display.
If the unit is turned on when the timer-on time comes
Timer does not work.
When you unplug the AC power cord or if a power failure occurs
The timer will be canceled. You need to set the clock first, then the timer again.
Using Sleep Timer
With Sleep Timer, you can fall asleep to music. You can set Sleep Timer when the unit is turned on.
How Sleep Timer actually works
The unit automatically turns off after the specified time length passes.
On the remote control ONLY:
1
Press SLEEP.
The time length until the shut-off time appears and the SLEEP indicator lights up on the display.
Each time you press the button, the time length changes as follows:
10
2
Wait for about 5 seconds after specifying the
30 60 90 120
20
Canceled
time length.
To check the remaining time until the shut-off time, press
SLEEP once so that the remaining time until the shut-off time appears for about 5 seconds.
SLEEP
To change the shut-off time, press SLEEP repeatedly until the desired time length appears on the display.
To cancel the setting, press SLEEP repeatedly until the SLEEP indicator goes off.
Sleep Timer is also canceled when you turn off the unit.
If you set the Sleep Timer after Daily Timer starts playing the selected source
Daily Timer is canceled.
If you set the Sleep Timer after Recording Timer starts recording
Recording Timer is canceled, but recording continues until Sleep Timer shuts off the power.
21
Page 25
Additional Information
Description of the PTY codes:
NEWS:News. AFFAIRS: Topical program expanding or enlarging upon the
news debate, or analysis.
INFO: Program the purpose of which is to impart advice in
the widest sense.
SPORT: Program concerned with any aspect of sports. EDUCATE: Educational programs. DRAMA: All radio plays and serials. CULTURE: Programs concerning any aspect of national or
regional culture, including language, theater, etc.
SCIENCE: Programs about natural sciences and technology. VARIED: Used for mainly speech-based programs such as
quizzes, panel games and personality interviews.
POP M: Commercial music of current popular appeal. ROCK M: Rock music. EASY M: Current contemporary music considered to be “easy-
listening.
LIGHT M: Instrumental music, and vocal or choral works. CLASSICS: Performances of major orchestral works,
symphonies, chamber music, etc.
OTHER M: Music not fitting into any of the other categories. WEATHER: Weather reports and forecasts. FINANCE: Stock Market reports, commerce, trading etc.
CHILDREN: Programs targeted at a young audience. SOCIAL: Programs about sociology, history, geography,
psychology and society.
RELIGION: Religious programs. PHONE IN: Involving members of the public expressing their
views either by phone or at a public forum.
TRAVEL: Travel information. LEISURE: Programs about recreational activities. JAZZ: Jazz music. COUNTRY: Songs which originate from, or continue the musical
tradition of the American Southern States.
NATION M: Current popular music of the nation or region in that
countrys language.
OLDIES: Music from the so-called golden age of popular
music.
FOLK M: Music which has its roots in the musical culture of a
particular nation.
DOCUMENT:Program concerning factual matters, presented in an
investigative style.
TRAFFIC: Traffic announcement.
Classification of the PTY codes for some FM stations may be different from the above list.
Troubleshooting
If you are having a problem with your unit, check this list for a possible solution before calling for service. If you cannot solve the problem from the hints given here, or the unit has been physically damaged, call a qualified person, such as your dealer, for service.
Symptom
No sound is heard.
Hard to listen to broadcasts because of noise.
The disc tray does not open or close. The disc does not play. The disc sound is discontinuous. The cassette holder cannot be opened.
Impossible to record.
Operations are disabled.
Unable to operate the unit from the remote control.
Connections are incorrect or loose.
Headphones are connected.
Antennas are disconnected.
The AM loop antenna is too close to the
unit.
The FM antenna is not properly extended and positioned.
The AC power cord is not plugged in. The disc is placed upside down. The disc is scratched or dirty. Power supply from the AC power cord has
been cut off while the tape was running. Small tabs on the back of the cassette are
removed. The built-in microprocessor may
malfunction due to external electrical interference.
The path between the remote control and the remote sensor on the unit is blocked.
The batteries are exhausted.
Cause
Action
Check all connections and make corrections. (See pages 6 to 8.)
Disconnect the headphones.
Reconnect the antennas correctly and
securely.
Change the position and direction of the AM loop antenna.
Extend the FM antenna at the best position.
Plug the AC power cord. Place the disc with the label side up. Clean or replace the disc. (See page 23.) Turn on the unit.
Cover the holes with adhesive tape.
Unplug the AC power cord and then plug it back in.
Remove the obstruction.
Replace the batteries.
22
Page 26
Maintenance
To get the best performance of the unit, keep your discs, tapes, and mechanism clean.
Handling discs
DO NOT use any solvent—such as conventional record cleaner, spray, thinner, or benzine—to clean the disc.
Remove the disc from its case by holding it at the edge while pressing the center hole lightly.
Do not touch the shiny surface of the disc, or bend the disc.
Put the disc back in its case after use to prevent warping.
Be careful not to scratch the surface of the disc when placing it back in its case.
Avoid exposure to direct sunlight, temperature extremes, and moisture.
To clean the disc
Wipe the disc with a soft cloth in a straight line from center to edge.
Cleaning the unit
Stains on the unit
Should be wiped off with a soft cloth. If the unit is heavily stained, wipe it with a cloth soaked in water-diluted neutral detergent and wrung well, then wipe clean with a dry cloth.
Since the unit may deteriorate in quality, become damaged or get its paint peeled off, be careful about the followings.
DO NOT wipe it with a hard cloth.DO NOT wipe it strong.DO NOT wipe it with thinner or benzine.DO NOT apply any volatile substance such as
insecticides to it.
DO NOT allow any rubber or plastic to remain in contact
with it for a long time.
Handling cassette tapes
If the tape is loose in its cassette, take up the slack by inserting a pencil in one of the reels and rotating.
If the tape is loose, it may get stretched, cut, or caught in the cassette.
Be careful not to touch the tape surface.
Avoid the following places to store the
tape:
In dusty placesIn direct sunlight or heatIn moist areasOn a TV or speakerNear a magnet
23
Page 27
Specifications
Amplifier
Output Power:
120 W (60 W + 60 W) at 6 (MAX.) 100 W (50 W + 50 W) at 6 (10 % THD)
Audio input sensitivity/Impedance (at 1 kHz)
AUX: 400 mV/48 k
Audio output level
AUX: 260 mV/5.8 k
Digital outputOPTICAL DIGITAL OUT
Signal wave length: 660 nm Output level: –21 dBm to –15 dBm
Speakers/Impedance: 6 Ω – 16 Ω
Tuner
FM tuning range: 87.50 MHz – 108.00 MHz AM tuning range:
MW: 522 kHz – 1 629 kHz LW: 144 kHz – 288 kHz
CD player
Dynamic range: 85 dB Signal-to-noise ratio: 90 dB Wow and flutter: Immeasurable
Speaker
Speaker units
Woofer: 12 cm cone x 1 Tweeter: 4 cm cone x 1
Impedance: 6 Dimensions (approx.): 160 mm x 256 mm x 211 mm (W/H/D) Mass (approx.): 2.3 kg each
Supplied Accessories
See page 6.
General
Power requirement: AC 230 V , 50 Hz Power consumption: 90 W (at operation)
1.2 W (on standby) Dimensions (approx.): 505 mm x 256 mm x 295 mm (W/H/D) Mass (approx.): 10.0 kg
Design and specifications are subject to change without notice.
Cassette deck
Frequency response
Normal (type I): 50 Hz – 14 000 Hz
Wow and flutter: 0.15 % (WRMS)
24
Page 28
VICTOR COMPANY OF JAPAN, LIMITED
EN
© 2003 VICTOR COMPANY OF JAPAN, LIMITED
0203MWMMDWJEM
Loading...