MICRO COMPONENT SYSTEM
UX-G800D
—Consists of CA-UXG800D and SP-UXG300
INSTRUCTIONS
GVT0250-001A
[B]
Warnings, Cautions and Others
CAUTION
The button in any position does not disconnect the
mains line.
Disconnect the mains plug to shut the power off
completely (the STANDBY lamp goes off).
The MAINS plug or an appliance coupler is used as the
disconnect device, the disconnect device shall remain
readily operable.
• When the System is on standby, the STANDBY lamp
lights red.
• When the System is turned on, the STANDBY lamp
goes off.
The power can be remote controlled.
CAUTION:
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
CAUTION:
• Do not block the ventilation openings or holes. (If
the ventilation openings or holes are blocked by a
newspaper or cloth, etc., the heat may not be able
to get out.)
• Do not place any naked flame sources, such as
lighted candles, on the apparatus.
• When discarding batteries, environmental problems
must be considered and local rules or laws
governing the disposal of these batteries must be
followed strictly.
• Do not expose this apparatus to rain, moisture,
dripping or splashing and that no objects filled
with liquids, such as vases, shall be placed on the
apparatus.
• Excessive sound pressure from earphones or
headphones can cause hearing loss.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover or cabinet.
There are no user serviceable parts inside the unit;
leave all servicing to qualified service personnel.
3. CAUTION: Visible and/or invisible class 1M laser
radiation when open. Do not view directly with
optical instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED
INSIDE THE UNIT.
IMPORTANT for the U.K.
DO NOT cut off the mains plug from this equipment.
If the plug fitted is not suitable for the power points in
your home or the cable is too short to reach a power
point, then obtain an appropriate safety approved
extension lead or consult your dealer.
BE SURE to replace the fuse only with an identical
approved type, as originally fitted.
If nonetheless the mains plug is cut off ensure to
remove the fuse and dispose of the plug immediately,
to avoid a possible shock hazard by inadvertent
connection to the mains supply.
If this product is not supplied fitted with a mains plug
then follow the instructions given below:
IMPORTANT:
DO NOT make any connection to the terminal which
is marked with the letter E or by the safety earth
symbol or coloured green or green-and-yellow.
The wires in the mains lead on this product are
coloured in accordance with the following code:
Blue: Neutral
Brown: Live
As these colours may not correspond with the
coloured markings identifying the terminals in your
plug proceed as follows:
The wire which is coloured blue must be connected
to the terminal which is marked with the letter N or
coloured black.
The wire which is coloured brown must be
connected to the terminal which is marked with the
letter L or coloured red.
IF IN DOUBT - CONSULT A COMPETENT
ELECTRICIAN.
Dear Customer,
This apparatus is in conformance with the valid
European directives and standards regarding
electromagnetic compatibility and electrical safety.
European representative of Victor Company of Japan,
Limited is:
JVC Technical Services Europe GmbH
Postfach 10 05 04
61145 Friedberg
Germany
G-1
CAUTION: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
1. Front: No obstructions and open spacing.
2. Sides/Top/Back: No obstructions should be placed in the areas shown by the dimensions below.
3. Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a
height of 10 cm or more.
Front view Side view
Information for Users on Disposal of Old equipment
[European Union]
This symbol indicates that the electrical and electronic equipment should not be
disposed as general household waste at its end-of-life. Instead, the product should
be handed over to the applicable collection point for the recycling of electrical and
electronic equipment for proper treatment, recovery and recycling in accordance
with your national legislation.
By disposing of this product correctly, you will help to conserve natural resources
and will help prevent potential negative effects on the environment and human
health which could otherwise be caused by inappropriate waste handling of this
product, please contact your local municipal office, your household waste disposal
Attention:
This symbol is only valid in
the European Union.
service or the shop where you purchased the product.
Penalties may be applicable for incorrect disposal of this waste, in accordance with
national legislation.
(Business users)
If you wish to dispose of this product, please visit our web page www.jvc-europe.
com to obtain information about the take-back of the product.
[Other Countries outside the European Union]
If you wish to dispose of this product, please do so in accordance with applicable
national legislation or other rules in your country for the treatment of old electrical
and electronic equipment.
G-2
Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the
Thank you for purchasing a JVC product.
best possible performance from the unit.
Contents
Precautions ...................................................................... 2
Getting Started ................................................................ 2
Supplied Accessories ................................................................................... 2
Prepare the Remote Control ........................................................................ 2
Connections ................................................................................................ 3
Basic and Common Operations ...................................... 5
Playing Back a Disc/USB Mass Storage Class Device .... 7
Loading a Disc ............................................................................................. 7
Connecting a USB Mass Storage Class Device .............................................. 7
Basic Disc/USB Mass Storage Class Device Operations ................................. 7
Playing Repeatedly—Repeat Play ............................................................. 8
Programming the Playing Order—Program Play ....................................... 8
Playing at Random—Random Play ............................................................ 8
Prohibiting Disc Ejection ............................................................................. 8
Listening to the Radio ..................................................... 9
Basic Tuner Operations ................................................................................ 9
Presetting Stations and Services ................................................................. 9
What is DAB System? .................................................................................. 10
Changing the DAB Information ................................................................... 10
Improving the DAB Reception ..................................................................... 10
Scanning Ensembles ................................................................................... 10
Receiving FM Stations with Radio Data System ........................................... 11
Changing the Radio Data System Information ............................................ 11
Searching for Programs by PTY Codes (PTY Search) ..................................... 11
Switching Temporarily to a Program of Your Choice Automatically ............ 11
Listening to Digital Audio Player ................................... 12
Setting the Clock and Using Timers ............................... 13
Setting the Clock ......................................................................................... 13
Setting the Sleep Timer ............................................................................... 13
Turning Off the System Automatically—AUTO STANDBY function ............. 13
Setting the Daily Timer ............................................................................... 14
Troubleshooting .............................................................. 15
Learning More about This System ................................. 16
Maintenance .................................................................... 19
Specifications ................................................................... 19
1
Precautions
Notes on the power cord
• When you are away on travel or otherwise for an
extended period of time, remove the plug from the
wall outlet.
• When unplugging the System from the wall outlet,
always pull the plug, not the power cord.
• Do not handle the power cord with wet hands.
• Disconnect the power cord before cleaning the
System or moving the System.
• Do not alter, twist or pull the power cord, or put
anything heavy on it, which may cause fire, electric
shock, or other accidents.
• If the cord is damaged, consult a dealer and have the
power cord replaced with a new one.
Avoid moisture, water, dust, and high
temperatures
• Do not place the System in moist or dusty places.
• If water gets inside the System, turn off the power and
remove the plug from the wall outlet, then consult
your dealer. Using the System in this state may cause
a fire or electrical shock.
Getting Started
Supplied Accessories
After unpacking, check to be sure that you have all the
following items.
• Remote control, RM-SUXG300R (× 1)
• Lithium coin battery CR2025 (× 1)
– The battery has been installed when shipped from
the factory.
• AM loop antenna (× 1)
• FM antenna (× 1)
• DAB antenna (× 1)
• Core filter (× 1), see page 18 for details
If anything is missing, consult your dealer immediately.
Prepare the Remote Control
When you use the remote control for the first time, pull
out the insulation sheet.
• Do not expose the System to direct sunlight or place
it near a heating device.
Notes on installation
• Select a place which is level, dry and neither too hot
nor too cold—between 5˚C and 35˚C.
• Do not install the System in a place subject to
vibrations.
• Do not put heavy objects on the System.
To prevent malfunction or damage of the System
• Do not insert any metallic objects, such as wires,
hairpins, coins, etc. into the System.
• Do not block the vents.
There are no user-serviceable parts inside. If
anything goes wrong, unplug the power cord and
consult your dealer.
NOTES:
• Store the battery in a place where children cannot reach.
If a child accidentally swallows the battery, consult a
doctor immediately.
• To prevent the battery from over-heating, cracking, or
starting a fire:
– Do not recharge, short, disassemble or heat the battery
or dispose of it in a fire.
– Do not leave the battery with other metallic materials.
– Wrap the battery with tape and insulate when
throwing away or saving it.
– Do not poke the battery with tweezers or similar tools.
• Dispose of battery in the proper manner, according to
federal, state, and local regulations.
• The batteries (battery pack or batteries installed) shall not
be exposed to excessive heat source such as sunshine, fire
or the like.
Insulation sheet
To Replace the Battery in the Remote Control
Lithium coin battery
(product number: CR2025)
CAUTION:
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
2
Connections
Do not connect the AC power cord until all other connections have been made.
NOTES:
• Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. Also, keep
the antennas away from metallic parts of the System, connecting cords, and the AC power cord. This could cause poor
reception.
• Make sure both the speakers are connected correctly and firmly.
• When connecting the speaker cords, match the polarity of the speaker terminals: red color to (+) and black color to (–).
• DO NOT connect more than one speaker to each terminal.
• DO NOT allow the conductor of the speaker cords to be in touch with the metallic parts of the System.
To connect the DAB antenna
(supplied)
Extend it so that you can receive your
desired ensembles.
DAB antenna (supplied)
Rear view
For better DAB reception
Disconnect the supplied DAB antenna, and connect an active
antenna.
(See “Improving the DAB Reception” on page 10.)
To a wall outlet
Plug the AC power cord only after all connections are complete.
3
To connect the FM antenna (supplied)
Extend it so that you can obtain the best reception.
FM antenna (supplied)
For better FM reception
Disconnect the supplied FM antenna, and connect
to an outdoor FM antenna using a 75 Ω wire with
coaxial type connector (IEC or DIN45325).
To connect the AM loop antenna (supplied)
AM loop antenna (supplied)
Turn it until the best reception
is obtained.
To connect the speaker cords
Outdoor FM antenna
(not supplied)
To assemble the AM loop antenna
Press and hold
InsertRelease
From right
speaker
Red
Black
From left
speaker
4
Basic and Common Operations
Point at the remote sensor on the front panel.
(The operating range is approx. 7 m.)
STANDBY lamp
PHONES jack
Stereo mini plug cord
How to cancel the demonstration
Press and hold DEMO button while on standby. (Refer to the attached “Information about the demonstration
function.”)
Using Headphones
Be sure to turn down the volume before connecting or putting on the headphones.
• Connecting the headphones will deactivate the speakers.
• Sound adjustments also affect the sound through the headphones.
NOTE:
DO NOT turn off (standby) the System with the volume set to an extremely high level; otherwise, the sudden blast of sound
can damage your hearing, speakers and/or headphones when you turn on the System or start playback.
5
To
Turn on or off (standby)
the power
Press
System Remote
Indication/Result
The STANDBY lamp on the System turns off/on.
Select a source
Adjust the volume
Drop the volume in a
moment
Activate the EALA
surround mode —
Emphasize the sound
(Sound Turbo function)
Reinforce the bass
sound (Active Hyper
Bass Pro function) —
Adjust the tone (Bass/
Treble)
—
—
See “Playing Back a Disc/USB Mass Storage Class Device” on
page 7.
See “Listening to the Radio” on page 9.
See “Listening to Digital Audio Player” on page 12.
Adjustable range: Level 0 (“VOL MIN”) to level 40 (“VOL MAX”).
To restore the volume, press again, or adjust the volume level.
The indicator lights up.
To cancel this function, press repeatedly until indicator
lights off.
The S.TURBO indicator lights up.
To cancel this function, press again.
Press and hold until the AHB indicator lights up.
• When Sound Turbo function is activated (see above), this
function cannot be activated.
To cancel this function, press and hold again when Sound
Turbo function is deactivated.
Press once for adjusting the bass level; twice for treble level,
then, press VOLUME +/–.
Adjustable range: –3 to +3.
Change the display
brightness
Change the display
information (Clock and
Source)
Set the ECO (ecology)
Mode
Press when the System is turned on.
—
To cancel this function, press again.
For setting the clock, see “Setting the Clock and Using Timers”
—
on page 13.
• Not applicable for FM.
Press when the System is on standby.
Setting the ECO mode allows you to reduce power consumption
—
by turning the display off while on standby.
To cancel this function, press again when the System is on
standby.
6
Playing Back a Disc/USB Mass Storage Class Device
The following operations are explained using
the remote control, unless mentioned otherwise.
However, if the System has the same or similar button
names, they can also be used for the operations.
This System can play back...
– CD.
– CD-R/CD-RW recorded in audio CD format (CD-DA) or
recorded MP3/WMA files in ISO 9660 format.
– USB mass storage class device containing MP3/WMA
files.
• When playing back an MP3 or WMA track, MP3 or
WMA indicator lights up.
Loading a Disc (on the System only)
1
2
3
Press to open the disc
tray.
• When using an 8 cm
disc, place it on the
inner circle of the disc
tray.
Press to close the disc
tray.
• Do not disconnect the USB mass storage class device
when the System is turned on. It may cause malfunction
of both this System and the device.
• Noise and static electricity may stop the USB mass
storage class device sound. In this case, disconnect and
connect the USB mass storage class device again after
turning off the System.
Basic Disc/USB Mass Storage Class
Device Operations
To play back the disc/USB mass storage class
device
• Current track number and elapsed
playing time appear.
For MP3/WMA files: Before current
track number and elapsed playing time
appear, the tag information appears if it
is recorded.
• During playback, press again to pause.
To stop playback
• While playback is stopped, total track
number and total playing time (for
MP3/WMA files, group number and track
number) appear.
To select a track
Select the next tracks.
Connecting a USB Mass Storage Class
Device
You can connect a USB mass storage class device such
as a USB flash memory device, MP3 player, multimedia
card reader, etc. to the System.
USB cable (not supplied)
NOTES:
• When connecting with a USB cable, use the USB 2.0 cable
whose length is less than 1 m.
• USB mass storage class device is charged through the
USB MEMORY terminal when the System is turned on and
the source is “USB.”
• You cannot connect a computer to the USB MEMORY
terminal of the System.
7
To go back to the beginning of the
current or previous tracks.
To select a group (MP3/WMA only)
Select the next groups.
Select the previous groups.
To forward search/reverse search
Press and hold to fast-forward the track
during playback.
To stop searching, release the button.
Press and hold to fast-reverse the track
during playback.
To stop searching, release the button.
NOTES:
• If no disc is inserted or no USB mass storage class device is
connected, “NO DISC” or “NO USB” appears on the main
display.
• If MP3/WMA files are not recorded on the disc or in the
USB mass storage class device, “NO PLAY” appears on the
main display.
Playing Repeatedly—Repeat Play
1
2
Press repeatedly to specify the repeat
mode as follows:
REP TRK: Repeats the current (or
specified) track. [ ]
REP GRP: Repeats all tracks in the
current group (MP3/WMA
only). [ ]
REP ALL: Repeats all tracks.
[ ALL ]
REP OFF: Normal playback
or
Programming the Playing Order
—Program Play
1
2
3
Repeat steps 2 and 3 to program other tracks
4
you want.
• If you try to program a 51st track, “FULL” will
5
During stops, press until the PRGM
(program) indicator lights up before
playing.
• For MP3/WMA files: Select a group
number, then a track number.
or
• For CD: Select a track number.
Press to program the selected group/
track.
appear.
The tracks are played back in the
programmed order.
Playing at Random—Random Play
1
2
Operations for Random Play
• To skip a track, press ¢.
• To go back to the beginning of the current track,
press 4.
• To exit from random play, press MODE while
playback is stopped.
RESUME Play (For MP3/WMA only)
When you stop the playback by one of the following
operations, this System stores the beginning of the
stopped track on the disc or USB mass storage class
device.
– Pressing 7 once
– Changing the source
When you start playback again, playback starts from
the stored position.
To clear the stored position, open the disc tray or
disconnect the USB mass storage class device.
• When you clear the stored position and start
playback, playback starts from the beginning of the
first track.
NOTE:
This function does not work in Program Play and
Random Play.
Press until the RND (random) indicator
lights up before you start playback.
or
Playback starts in random
order.
Random Play ends when all
tracks are played back.
Prohibiting Disc Ejection
(on the System only)
You can lock the disc tray so that no one can eject the
loaded disc.
• This is possible while the System is on standby.
To cancel the prohibition,
repeat the same procedure.
Operations for Program Play (while not playing)
• To check the programmed contents, press 4 or
¢.
• To add tracks, repeat steps 2 and 3 above.
• To erase the last programmed track, press CANCEL.
• To erase the entire program, press and hold CANCEL
for about 2 seconds.
• To exit from program play, press MODE.
– The stored program is kept.
8
Listening to the Radio
The following operations are explained using
the remote control, unless mentioned otherwise.
However, if the System has the same or similar button
names, they can also be used for the operations.
Basic Tuner Operations
To select a band
Press repeatedly to select the band:
(On the System)
(On the remote
control)
To change the FM reception mode
(When an FM stereo broadcast is hard to receive)
For FM/AM
To select a frequency
or
To tune in to a preset station
or
* Appears only if DAB/FM/AM (TUNER)
button on the System is pressed.
• The selected frequency band
appear.
• When an FM stereo broadcast or a
DAB service with sufficient signal
strength is tuned in, the S (stereo)
or TUNED indicator lights up
respectively.
When you change the source to
DAB for the first time after plugging
in the AC power cord, the System
automatically scans the DAB bands
for available ensembles. (See page
10.)
Press to improve reception.
The M (mono) indicator lights up.
Stereo effect will be lost.
To restore the stereo effect, press
again.
Press and hold for more than 2
seconds.
The System starts searching for
stations and stops when a station of
sufficient signal strength is tuned in.
• Press during searching to stop.
• Press repeatedly to change the
frequency step by step.
Press to select its preset number.
• For presetting stations, see the right
column.
For DAB
To select an ensemble
Press 4/¢ while “ENSEMBLE” is
displayed.
• You can select from the ensembles
found in the ensemble scanning.
or
To select a service (either primary or secondary)
While tuning in to a service, press to
or
To tune in to a preset service
or
To tune in to all ensembles
1
2
change services.
• When you reach the last/first service
of an ensemble and press ¢/4,
you skip to the next/previous
ensemble respectively. It may take
some time to change ensembles.
• If the System is not tuned in to any
services, pressing ¢/4 will start
selecting an ensemble.
Press to select the preset number of
the pre-selected services.
• For presetting services, see below.
“ENSEMBLE” appears on the display.
Press and hold for more than 2
seconds.
The frequency changes every
or
second through all ensembles
regardless of the signal status.
• Release the button when the
desired ensemble is reached.
Presetting Stations and Services
You can preset 30 FM stations, 15 AM stations, and 30
DAB services manually.
Tune in to a station/service you want to preset.
1
• You can also store the monaural reception
mode for FM stations.
2
3
Press to activate the preset number
entry mode.
• Finish the following steps while
the indication on the display is
flashing.
Press to select a preset number
for the station/service you want to
or
store.
9
4
Press to store the station/service.
NOTES:
• If you store a new station/service into an occupied preset
number, the previously stored one in that number will be
erased.
• When you preset DAB services, you can only preset
primary services. If you select a secondary service to store,
its primary service is stored instead.
What is DAB System?
DAB (Digital Audio Broadcasting) is one of the digital
radio broadcasting systems available today. It can
deliver digital quality sound without any annoying
interference or signal distortion. Furthermore, it
can carry text, pictures and data. In contrast to FM
broadcast, where each program is transmitted on its
own frequency, DAB combines several programs (called
“services”) to form one “ensemble.” “Primary services”
(main radio stations) are sometimes accompanied by
“secondary services” to broadcast additional programs.
CAUTION:
Electrostatic discharge from your body may cause
noise from the speakers and you cannot hear the
broadcast.
If this happens, turn off the System (on standby), then
turn it on again.
Changing the DAB Information
Each time you press the button, the main
display changes as follows:
Improving the DAB Reception
With the supplied DAB antenna, you may not be able
to receive L-Band ensembles. You can improve the
reception of both L-Band and Band III ensembles by
connecting an active antenna (see page 3).
To supply power to the active antenna
After connecting an active antenna,
press and hold for more than 2 seconds
while the System is on standby. Power is
supplied to the active antenna when DAB
is selected as the source and “ANT.P ON”
appears on the display.
To cut the power supply, press and hold
the button again on standby. Then
“ANT.P OFF” appears on the display.
• You cannot change this setting when
the ECO mode is activated (see page 6).
Scanning Ensembles
With the ensemble scanning function, the System scans
the DAB bands to pick out available ensembles under
your receiving condition.
• When you change the source to DAB for the first
time after plugging in the AC power cord, the System
automatically performs the scanning.
• When you moved your System or adjusted the
antenna position, perform the scanning manually.
To start the scanning
Press and hold for more than 2 seconds
while DAB is selected as the source.
To cancel the scanning, press CANCEL.
If you change to other source during ensemble
scanning, the System will restart the scanning when
DAB is selected as the source again.
• To cancel the scanning and stop restarting the scan,
press CANCEL.
PTY: Program Type (See page 11.)
DLS: Dynamic Label Segment (text
messages the station sends)
* The preset number is displayed only when
the service has been selected using the
PRESET UP/DOWN keys.
NOTES:
• If no signals are sent, “NOSIGNAL” (instead of Service
Label), “NO PTY” (instead of PTY) or “NO TEXT” (instead of
DLS) appears on the display.
• If a preset channel which has no signal is selected,
“EMPTY” (instead of Service Label) appears on the display.
When the scanning is complete, the System starts
playing the first service of the ensemble found first.
10
Receiving FM Stations with Radio
Data System
Radio Data System allows FM stations to send an
additional signal along with their regular program
signals.
With the System, you can receive the following types of
Radio Data System signals.
PS (Program Service):
Shows commonly known station names.
PTY (Program Type):
Shows types of broadcast programs.
RT (Radio Text):
Shows text messages the station sends.
Enhanced Other Networks:
Provides the information about the types of
programs broadcast by the Radio Data System
stations on different networks.
NOTE:
If you want to know more about Radio Data System, visit
<http://www.rds.org.uk>.
• For details about PTY codes, see page 17.
1
2
3
• To stop searching any time during search, press
PTY SEARCH.
• To continue searching after it stops on an
unwanted program, press PTY SEARCH again while
the PTY code is flashing on the display.
Press to enter the PTY code setting
mode.
“PTY” and “SELECT” appear
alternately.
Select a PTY code.
or
The System searches for 30 preset
FM stations, stops when it finds the
one you have selected, and tunes in
to that station.
NOTE:
If no program is found, “NOTFOUND” appears.
Changing the Radio Data System
Information
Each time you press the button, the
information changes as follows:
NOTES:
• “PS,” “PTY,” or “RT” is displayed while the System is
searching for the corresponding Radio Data System
information.
• If no Radio Data System signals are sent by a station,
“NO PS,” “NO PTY,” or “NO RT” appears.
Searching for Programs by PTY Codes
(PTY Search)
While listening to an FM station:
You can locate a particular kind of program from the 30
preset stations (see page 9) by specifying a PTY code.
While listening to a DAB service:
You can locate a particular kind of program from
among all the services you can receive by specifying
the PTY codes.
Switching Temporarily to a Program
of Your Choice Automatically
The Enhanced Other Networks function allows the
System to switch temporarily to a station/service
broadcasting a program of your choice (TA, NEWS, or
INFO).
• While you are listening to an FM station, the System
can switch to one of the preset FM stations.
• While you are listening to a DAB service, the System
can switch to another DAB service.
• This function works while listening to a station/service
providing the required signals.
Press repeatedly to select the program
type as follows:
TA: Traffic announcement in your
area.
NEWS: News
INFO: Program the purpose of which
is impart advice in the widest
sense.
11
How the Enhanced Other Networks function actually works:
Case 1
If no station/service is broadcasting the program of your choice
The System continues tuning in to the current station/service.
\ When a station/service starts broadcasting the program of your choice, the System automatically switches to
that station/service. The PTY code indicator starts flashing.
\ When the program is over, the System goes back to the previously tuned station/service, but the function still
remains active (the indicator stops flashing and remains lit).
Case 2
If a station/service is broadcasting the program of your choice
The System automatically switches to the station/service. The PTY code indicator starts flashing.
\ When the program is over, the System goes back to the previously tuned station/service, but the function still
remains active (the indicator stops flashing and remains lit).
Case 3
If the station/service currently tuned in is broadcasting the program of your choice
The PTY code indicator starts flashing.
\ When the program is over, the indicator stops flashing (the function still remains active).
Listening to Digital Audio Player
The following operations are explained using
the remote control, unless mentioned otherwise.
However, if the System has the same or similar button
names, they can also be used for the operations.
Front view
Digital Audio Player
Stereo mini plug cord
(not supplied)
1
2
3
4
Turn the volume to minimum.
Press repeatedly to select “AUDIO IN.”
Start playing the Digital Audio Player connected.
Adjust the volume.
To audio output (or
headphone out, etc.)
To Adjust the Audio Input Level
If the sound from the Digital Audio Player connected
to the AUDIO IN jack is too loud or too quiet, you can
change the audio input level through the AUDIO IN jack
(without changing the volume level).
Press and hold for more than 2 seconds
while “AUDIO IN” is selected as the source.
You can select one of three levels as
follows:
As the number increases, the sound
becomes louder.
12
Setting the Clock and Using Timers
The following operations are explained using
the remote control, unless mentioned otherwise.
However, if the System has the same or similar button
names, they can also be used for the operations.
Setting the Clock
Without setting the built-in clock, you cannot use Daily
Timer and Sleep Timer.
• “0:00” flashes on the main display until you set the
clock.
1
2
• To exit from the clock setting, press CLOCK/TIMER as
required.
• To go back to the previous step, press CANCEL.
or
Press to activate the clock setting
mode.
• If you have already adjusted
the clock before, press the
button repeatedly until the
clock setting mode is selected.
Adjust the hour, then the
minute.
Setting the Sleep Timer
When the System is on, press repeatedly to
specify the time (in minutes) as follows:
The SLEEP indicator lights up.
• To check the remaining time until the System shuts
off, press once.
Turning Off the System
Automatically—AUTO STANDBY
function
To cancel this function, press and hold again.
(only for Disc/USB)
Press and hold until the A.STBY indicator
lights on the display.
• The A.STBY indicator starts flashing after
playback stops.
If no operation is done for about 3
minutes, the System turns off.
• Not applicable for DAB/FM/AM/AUDIO
IN.
13
Setting the Daily Timer
Using Daily Timer, you can wake up with your favorite music.
• You can store three Daily Timer settings; however, you can activate only one of the Daily Timers.
1
Press repeatedly to select one of the timer setting modes you want to set—DAILY 1 ON
time, DAILY 2 ON time, or DAILY 3 ON time—as follows:
2
or
3
• To exit from the timer setting, press CLOCK/TIMER as required.
• To correct a misentry during the process, press CANCEL. You can return to the previous step.
1 Adjust the hour then the minute for on-time.
2 Adjust the hour then the minute for off-time.
3 Select the playback source—“DAB,” “TUNER-FM,” “TUNER-AM,” “DISC,” “AUDIO IN,” or
“USB.”
4 For “DAB/FM/AM”: Select a preset channel.
For “DISC” or “USB”: Select a track. (For MP3/WMA: Select the group, then the track
number.)
For “AUDIO IN”: Make the connected device ready for playback.
5 Select the volume.
• You can select the volume level (“VOLUME 0” (VOL MIN) to “VOLUME 40” (VOL MAX)
and “VOLUME – –”). If you select “VOLUME – –,” the volume is set to the last level when
the System is turned off.
Turn off the System (on standby).
• When the on-time comes, the System sets the volume gradually to the preset level.
To Turn Off the Daily Timer
1 Press repeatedly to select “DAILY 1,” “DAILY 2,” or “DAILY 3.”
2
To turn on the Daily Timer again, select one of the timer settings by pressing CLOCK/TIMER, then press SET.
14
Troubleshooting
If you are having a problem with your System, check
this list for a possible solution before calling for service.
General
Power does not come on.
\ Power plug is not inserted securely. Plug in securely.
Adjustments or settings are suddenly canceled
before you finish.
\ There is a time limit. Repeat the procedure again.
Operations are disabled.
\ The built-in microprocessor may malfunction due
to external electrical interference. Unplug the AC
power cord and then plug it back in.
Unable to operate the System from the remote
control.
\ The path between the remote control and the
remote sensor on the System is blocked.
\ The battery is exhausted.
No sound is heard.
\ Speaker connections are incorrect or loose.
\ Headphones are connected.
The System does not work properly.
\ Many functions of this System are implemented
by microcomputers. If the System does not work
correctly, disconnect the AC power cord from the
wall outlet, wait for a while, and connect the cord
again.
Disc/USB Mass Storage Class Device Operations
The disc/USB mass storage class device does not play.
\ The disc is placed upside down. Place the disc with
the label side up.
\ The disc is recorded with the “packet writing (UDF
file system).” It cannot be played. Check the files you
want to play back.
\ The USB mass storage class device is not connected
properly.
MP3/WMA groups and tracks are not played back as
you expect.
\ Playing order is determined when the groups and
tracks were recorded. It depends on the writing
application.
The disc/USB mass storage class device sound is
discontinuous.
\ The disc is scratched or dirty.
\ MP3/WMA files have not been properly copied into
the USB mass storage class device.
Sounds from USB mass storage class device are
interrupted.
\ Noise and static electricity may stop the sound. In
this case, disconnect and connect the USB mass
storage class device again after turning off the
System.
The disc tray does not open or close.
\ The AC power cord is not plugged in.
\ Disc ejection is prohibited (see page 8).
Radio Operations
Hard to listen to broadcasts because of noise.
\ Antennas connections are incorrect or loose.
\ The AM loop antenna is too close to the System.
\ The FM antenna is not properly extended and
positioned.
\ Electrostatic discharge from your body may cause
noise. If this happens, turn off and on the System
again.
Cannot receive an ensemble.
\ Your area is not covered by the ensemble.
\ The DAB antenna is not properly extended
or positioned. Adjust the antenna and try the
ensemble scanning again.
\ Connect an active antenna (not supplied).
Timer Operations
Daily Timer does not work.
\ The System has been turned on when the on-time
comes. Timer starts working only when the System
is turned off.
15
Learning More about This System
Basic and Common Operations (see pages 5 and 6)
• Pressing one of the source buttons also turns on the
System and starts playing back if the source is ready
or connected.
Playing Back a Disc/USB Mass Storage Class Device
(see pages 7 and 8)
• This System cannot play “packet write” discs.
• For MP3/WMA playback...
– In this manual, “file” and “track” are interchangeably
used for MP3/WMA operations.
– This System can show the Tag data (Version 1).
– MP3/WMA discs are required a longer readout time
than regular CDs. (It depends on the complexity of
the group/file configuration.)
– Some MP3/WMA files cannot be played back and
will be skipped. This result from their recording
processes and conditions.
– When making MP3/WMA discs, use ISO 9660 Level 1
or Level 2 for the disc format.
– This System can play back MP3/WMA files with the
extension code <.mp3> or <.wma> (regardless of
the letter case—upper/lower).
– It is recommended that you make each MP3/WMA
file at a sampling rate of 44.1 kHz and at bit rate of
128 kbps. This System cannot play back files made
at bit rate of less than 64 kbps.
– Playback order of MP3/WMA tracks may be different
from the one you have intended while recording. If
a folder does not include MP3/WMA tracks, they are
ignored.
• Do not use the following USB devices...
– Whose rating is other than 5 V and exceeds 500 mA.
– Equipped with special functions such as data
security functions.
– Divided by 2 or more partitions.
• For the USB mass storage class device playback...
– When connecting a USB mass storage class device,
also refer to its manual.
– Connect one USB mass storage class device to the
System at a time. Do not use a USB hub.
– This System is compatible with USB 2.0 Full Speed.
– You can play back MP3/WMA files in a USB mass
storage class device (maximum data transfer rate:
2 Mbps).
– You cannot play back a file larger than 2 Gigabyte.
– This System may not play back some USB mass
storage class devices and does not support DRM
(Digital Rights Management).
• This System can recognize up to 99 groups in a disc.
The total number of groups and tracks (in a disc) that
can be recognized by the System is 512 (for MP3/
WMA).
• This System can recognize up to 99 groups and 9 999
tracks (with a maximum number of 255 tracks in a
group) in a USB mass storage class device.
Listening to the Radio (see pages 9 to 11)
• The time shown on the display is based on the builtin clock of the System, not on the information sent
through DAB or Radio Data System.
• The Enhanced Other Networks function is available
only when tuning in to FM.
Setting the Clock and Using Timers (see pages 13
and 14)
• You can set the clock and Daily Timer while the Save
Mode is turned on. While setting the clock or Daily
Timer, the display is turning on.
• The clock may gain or lose 1 to 2 minutes per month.
If this happens, readjust the clock.
• When you unplug the AC power cord or if a power
failure occurs, the clock and the timer will be
canceled. You need to set the clock first, then the
timer again.
Timer Priority:
• If you set the Sleep Timer after Daily Timer starts
playing the selected source, Daily Timer is canceled.
16
Description of the PTY codes for Radio Data System and DAB
NEWS: News.
AFFAIRS: Topical program expanding or enlarging
upon the news—debate, or analysis.
INFO: Programs the purpose of which is to
impart advice in the widest sense.
SPORT: Programs concerned with any aspect of
sports.
EDUCATE: Educational programs.
DRAMA: All radio plays and serials.
CULTURE: Programs concerning any aspect of
national or regional culture, including
language, theater, etc.
SCIENCE: Programs about natural sciences and
technology.
VARIED: Used for mainly speech-based programs
such as quizzes, panel games and
personality interviews.
POP M: Commercial music of current popular
appeal.
ROCK M: Rock music.
EASY M: Current contemporary music considered
to be “easy-listening”.
LIGHT M: Instrumental music, and vocal or choral
works.
CLASSICS: Performances of major orchestral works,
symphonies, chamber music, etc.
OTHER M: Music not fitting into any of the other
categories.
WEATHER: Weather reports and forecasts.
* Only Radio Data System has this PTY code.
FINANCE: Stock Market reports, commerce, trading
CHILDREN: Programs targeted at a young audience.
SOCIAL: Programs about sociology, history,
RELIGION: Religious programs.
PHONE IN: Involving members of the public
TRAVEL: Travel information.
LEISURE: Programs about recreational activities.
JAZZ: Jazz music.
COUNTRY: Songs which originate from, or continue
NATION M: Current popular music of the nation or
OLDIES: Music from the so-called “golden age” of
FOLK M: Music which has its roots in the musical
DOCUMENT: Programs concerning factual matters,
TEST *: Broadcasts for testing emergency
ALARM *: Emergency announcement.
NONE *: No program type, undefined program,
etc.
geography, psychology and society.
expressing their views either by phone or
at a public forum.
the musical tradition of the American
Southern States.
region in that country’s language.
popular music.
culture of a particular nation.
presented in an investigative style.
broadcast equipment or unit.
or difficult to categorize into particular
types.
NOTE:
Classification of the PTY codes for some FM stations may be different from the above list.
17
Display Information
1 Source indicators (See page 6.)
2 File type indicators (See page 7.)
3 Play mode indicators (See page 8.)
4 Surround mode indicator (See page 6.)
5 S.TURBO (Sound Turbo) indicator (See page 6.)
6 TUNED indicator (See page 9.)
7 AHB indicator (See page 6.)
8 Source indicators (See page 6.)
9 FM reception indicators (See page 9.)
p DAB ensembles (L-Band and Band III) indicators (See
page 10.)
q Main display
w Radio Data System indicators (See page 11.)
e A.STBY (Auto Standby) indicator (See page 13.)
r SLEEP indicator (See page 13.)
t Timer mode indicators (See page 14.)
Attaching the Core Filter
Attach the provided core filter to the USB cable to reduce interference.
1
2
To the System
3
Stopper
USB cable
2 cm
Release the stopper of the core filter.
Run the USB cable through the core filter, leaving approx. 2 cm
between the unit-side end of the USB cable and the core filter.
Firmly wind the USB cable once inside the cutout of the core
filter.
Close the core filter until you hear a clicking sound.
NOTE:
Do not damage the USB cable by applying excessive power when winding.
18
Maintenance
To get the best performance of the System, keep your
discs and mechanism clean.
Handling discs
• Remove the disc from its case by holding it at the
edge while pressing the center hole lightly.
• Do not touch the shiny surface of the disc, or bend
the disc.
• Put the disc back in its case after use.
• Be careful not to scratch the surface of the disc when
placing it back in its case.
• Avoid exposure to direct sunlight, temperature
extremes, and moisture.
To clean the disc:
• Wipe the disc with a soft cloth in a straight line from
center to edge.
Specifications
Amplifier section
OUTPUT POWER:
60 W (30 W + 30 W) at 4 Ω (10% THD)
Speakers/Impedance: 4 Ω – 16 Ω
Audio input AUDIO IN: 500 mV/47 kΩ (at “IN LVL1”)
250 mV/47 kΩ (at “IN LVL2”)
125 mV/47 kΩ (at “IN LVL3”)
Digital input: USB MEMORY
Tuner section
FM tuning range: 87.50 MHz – 108.00 MHz
AM tuning range: 522 kHz – 1 629 kHz
DAB tuning range: BAND III: 174.928 MHz
– 239.200 MHz
L-BAND: 1 452.960 MHz
– 1 490.624 MHz
CD player section
Dynamic range: 88 dB
Signal-to-noise ratio: 85 dB
Wow and flutter: Immeasurable
Cleaning the System
• Stains should be wiped off with a soft cloth. If the
System is heavily stained, wipe it with a cloth soaked
in water-diluted neutral detergent and wrung well,
then wipe clean with a dry cloth.
• Since the System may deteriorate in quality, become
damaged or get its paint peeled off, be careful about
the following:
– DO NOT wipe it hard.
– DO NOT wipe it with thinner or benzine.
– DO NOT apply any volatile substance such as
insecticides to it.
– DO NOT allow any rubber or plastic to remain in
contact for a long time.
Speakers
Speaker units: 10 cm cone x 1
Impedance: 4 Ω
Dimensions (approx.): 160 mm x 250 mm x 150 mm
(W/H/D)
Mass (approx.): 1.6 kg each
General
Power requirements: AC 230 V , 50 Hz
Power supply to USB mass storage class device:
DC 5 V 500 mA
Power consumption: 25 W (power on)
6.5 W (standby mode)
1 W or less (ECO Mode)
Dimensions (approx.): 165 mm x 251 mm x 269 mm
(W/H/D)
Mass (approx.): 2.6 kg
Specifications and appearance are subject to change
without prior notice.
USB storage
USB specification: Compatible with USB 2.0 Full
Speed
Compatible device: Mass storage class
Compatible file system: FAT16, FAT32
Bus power supply: Max. 500 mA
19
JVC bears no responsibility for any loss of data in USB
mass storage class device while using this System.
Microsoft and Windows Media are either registered
trademarks or trademarks of Microsoft Corporation in
the United States and/or other countries.
“SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT”
This equipment has been designed and manufactured to meet international safety standards but, like any
electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured.
Do read the operating instructions before you attempt to use the equipment.
Do ensure that all electrical connections (including the mains plug, extension leads and interconnections
between pieces of equipment) are properly made and in accordance with the manufacturer’s instructions.
Switch off and withdraw the mains plug when making or changing connections.
Do consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.
Do be careful with glass panels or doors on equipment.
DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is
damaged in any way—switch off, withdraw the mains plug and consult your dealer.
DON’T remove any fixed cover as this may expose dangerous voltages.
DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed
for unattended operation or has a standby mode.
Switch off using the switch on the equipment and make sure that your family know how to do this.
Special arrangements may need to be made for infirm or handicapped people.
DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements of
traffic safety. It is illegal to watch television whilst driving.
DON’T listen to headphones at high volume as such use can permanently damage your hearing.
DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings.
Overheating will cause damage and shorten the life of the equipment.
DON’T use makeshift stands and NEVER fix legs with wood screws—to ensure complete safety always fit the
manufacturer’s approved stand or legs with the fixings provided according to the instructions.
DON’T allow electrical equipment to be exposed to rain or moisture.
ABOVE ALL
– NEVER let anyone, especially children, push anything into holes, slots or any other opening in the case
—this could result in a fatal electrical shock.;
– NEVER guess or take chances with electrical equipment of any kind—it is better to be safe than sorry!
SAFETY INSTRUCTIONS
20
MICRO COMPONENT SYSTEMUX-G800D
EN
© 2008 Victor Company of Japan, Limited
0408WMKMDWJMM
Loading...