Enter below the Model No. and Serial
No. which are located either on the rear,
bottom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
GVT0052-005A
[A]
Warnings, Cautions and Others
Caution — STANDBY/ON button!
Disconnect the mains plug to shut the power off completely.
The STANDBY/ON button in any position does not
disconnect the mains line. The power can be remote controlled.
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
CAUTION
• Do not block the ventilation openings or holes.
(If the ventilation openings or holes are blocked by
a newspaper or cloth, etc., the heat may not be able
to get out.)
• Do not place any naked flame sources, such as
lighted candles, on the apparatus.
• When discarding batteries, environmental problems
must be considered and local rules or laws
governing the disposal of these batteries must be
followed strictly.
• Do not use this apparatus in a bathroom or places
with water. Also do not place any containers filled
with water or liquids (such as cosmetics or
medicines, flower vases, potted plants, cups, etc.)
on top of this apparatus.
– G-1 –
IMPORTANT FOR LASER PRODUCTS
REPRODUCTION OF LABELS
1 CLASSIFICATION LABEL, PLACED ON REAR
ENCLOSURE
CLASS 1
LASER PRODUCT
2 WARNING LABEL, PLACED INSIDE THE UNIT
DANGER: Invisible laser
radiation when open and
interlock failed or defeated.
AVOID DIRECT EXPOSURE
TO BEAM. (e)
VARNING: Osynlig laserstrålning när denna del är
öppnad och spärren är
urkopplad. Betrakta ej
strålen. (s)
ADVARSEL: Usynlig laserstråling ved åbning, når
sikkerhedsafbrydere er ude
af funktion. Undgå udsættelse for stråling (d)
1. CLASS 1 LASER PRODUCT
2. DANGER: Invisible laser radiation when open and inter-
lock failed or defeated. Avoid direct exposure to beam.
3. CAUTION: Do not open the top cover. There are no user
serviceable parts inside the Unit; leave all servicing to
qualified service personnel.
VARO: Avattaessa ja suojalukitus ohitettaessa olet
alttiina näkymättömälle
lasersäteilylle. Älä katso
säteeseen. (f)
Caution: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
1 Front:No obstructions and open spacing.
2 Sides/ Top/ Back: No obstructions should be placed in the areas shown by the dimensions below.
3 Bottom:Place on the level surf ace. Maintain an adequate air path for ventilation by placing on a
stand with a height of 10 cm or more.
Front viewSide view
1 cm
15 cm
(5 15/16 in.)
7
(
/16 in.)
CA-MXGT90
CA-MXGT80
CA-MXG70
15 cm
(5
15
/16 in.)
1 cm
(7/16 in.)
15 cm
(5
15
/16 in.)
10 cm
(3
15
/16 in.)
15 cm
(5
15
/16 in.)
15 cm
15
(5
CA-MXGT90
CA-MXGT80
CA-MXG70
/16 in.)
– G-2 –
Introduction
We would like to thank you for purchasing one of our JVC products.
Before operating this unit, read this manual carefully and thoroughly to
obtain the best possible performance from your unit, and retain this manual
for future reference.
About This Manual
This manual is organized as follows:
• The manual mainly explains operations using the
buttons and controls on the unit. You can also use the
buttons on the remote control if they have the same or
similar names (or marks) as those on the unit.
If operation using the remote control is different from
that using the unit, it is then explained.
• Basic and common information that is the same for many
functions is grouped in one place, and is not repeated in
each procedure. For instance, we do not repeat the
information about turning on/off the unit, setting the
volume, changing the sound effects, and others, which are
explained in the section “Common Operations” on pages 9
to 11.
• The following marks are used in this manual:
Gives you warnings and cautions to prevent
from damage or risk of fire/electric shock.
Also gives you information which is not good
for obtaining the best possible performance
from the unit.
Gives you information and hints you had better
know.
Power sources
• When unplugging from the wall outlet, always pull the
plug, not the AC power cord.
DO NOT handle the AC power cord with wet
hands.
Moisture condensation
Moisture may condense on the lens inside the unit in the
following cases:
• After starting heating in the room
• In a damp room
• If the unit is brought directly from a cold to a warm place
Should this occur, the unit may malfunction. In this case,
leave the unit turned on for a few hours until the moisture
evaporates, unplug the AC power cord, and then plug it in
again.
Others
• Should any metallic object or liquid fall into the unit,
unplug the unit and consult your dealer before operating
any further.
• If you are not going to operate the unit for an extended
period of time, unplug the AC power cord from the wall
outlet.
Precautions
Installation
• Install in a place which is level, dry and neither too hot nor
too cold — between 5˚C (41˚F) and 35˚C (95˚F).
• Install the unit in a location with adequate ventilation to
prevent internal heat buildup in the unit.
• Leave sufficient distance between the unit and the TV.
• Keep the speakers away from the TV to avoid interference
with TV.
DO NOT install the unit in a location near heat
sources, or in a place subject to direct sunlight,
excessive dust or vibration.
DO NOT disassemble the unit since there are no
user serviceable parts inside.
If anything goes wrong, unplug the AC power cord and
consult your dealer.
– 1 –
Contents
Location of the Buttons and Controls....................... 3
Front Panel ................................................................. 3
Remote Control .......................................................... 5
8 CD 3¥8 (play/pause) button and lamp (9, 14 – 16, 20)
Pressing this button also turns on the unit.
9 FM/AM button and lamp (9, 12)
Pressing this button also turns on the unit.
p AUX button and lamp (9)
Pressing this button also turns on the unit.
q CD play mode buttons
• REPEAT button (16)
• PROGRAM button (15)
• RANDOM button (16)
w CLOCK/TIMER button (9, 21 – 24)
e PHONES jack (10)
r CD REC START button (19, 20)
t EDIT button (20)
y Deck A cassette holder (17)
u 0 EJECT button for deck A (17)
i Disc number buttons and lamps (CD1, CD2, and CD3)
(14, 15, 19, 20)
Pressing one of these buttons also turns on the unit.
o SET/DISPLAY button (9, 11, 12, 15, 20 – 24)
; 0 (Disc tray open/close) (CD1, CD2, and CD3) buttons
(13, 14, 16)
Pressing one of these buttons also turns on the unit.
a CANCEL/DEMO button (8, 9, 15, 20 – 24)
3
9
s SOUND MODE control (10)
d SUBWOOFER LEVEL + / – control (10)
f TUNING + / – buttons (12)
1 / ¡ (fast left/fast right) buttons (11, 14, 17)
g VOLUME + / – control (10)
h 7 (stop) button (14 – 20, 23)
j Tape operation buttons
• TAPE A/B button (17)
• REVERSE MODE button (17, 19, 20)
• REC START/STOP button (18 – 20, 23)
k DUBBING button (19)
l Deck B cassette holder (17 – 20, 23)
/ EJECT 0 button for deck B (17, 18)
w FM MODE button (12)
e CD 3¥8 button (9, 14 – 16)
Pressing this button also turns on the unit.
r ¢ (forward search) button (12, 14 – 17)
t TAPE 23 button (9, 17, 18)
Pressing this button also turns on the unit.
y TAPE A/B button (17)
u SUBWOOFER LEVEL + / – buttons (10)
i VOLUME + / – buttons (10)
6
7
STANDBY/ON
CD-R/RW PLAYBACK
u
i
STANDBY
PLAY & EXCHANGE
When using the remote control, point it at
the remote sensor on the front panel.
– 5 –
Getting Started
Continued
Supplied Accessories
Make sure that you have all the following items.
The number in the parentheses indicates the quantity of the
pieces supplied.
• AM loop antenna (1)
• FM antenna (1)
• Remote control (1)
• Batteries (2)
If anything is missing, consult your dealer immediately.
Putting the Batteries into the Remote Control
Insert the batteries — R6(SUM-3)/AA(15F) — into the
remote control, by matching the polarity (+ and –) on the
batteries with the + and – markings on the battery
compartment.
When the remote control can no longer operate the unit,
replace both batteries at the same time.
1
Connecting Antennas
FM antenna
ANTENNA
AM EXT
LOOP
FM 75
COAXIAL
FM antenna (supplied)
1 Attach the FM antenna to the FM 75 Ω
COAXIAL terminal.
2 Extend the FM antenna.
3 Fasten it up in the position which gives you
the best reception, then fix it on the wall, etc.
2
R6(SUM-3)/AA(15F)
3
• DO NOT use an old battery together with a
new one.
• DO NOT use different types of batteries
together.
• DO NOT expose batteries to heat or flame.
• DO NOT leave the batteries in the battery
compartment when you are not going to use
the remote control for an extended period of
time. Otherwise, it will be damaged from
battery leakage.
About the supplied FM antenna
The FM antenna supplied with this unit can be used as temporary
measure. If reception is poor, you can connect an outdoor FM
antenna.
To connect an outdoor FM antenna
Before connecting it, disconnect the supplied FM antenna.
Outdoor FM antenna
(not supplied)
ANTENNA
AM EXT
LOOP
FM 75
COAXIAL
A 75 Ω antenna with coaxial type connector should be
used.
– 6 –
AM antenna
SUBWOOFERS
MAIN
SPEAKERS
CAUTION: SPEAKER
IMPEDANCE
616
LEFT
LEFT
RIGHT
RIGHT
Connecting Speakers
ANTENNA
1
AM EXT
AM LOOP
FM 75
COAXIAL
Vinyl-covered wire
(not supplied)
2
AM loop antenna
(supplied)
1
Connect the AM loop antenna to the AM
LOOP terminals as illustrated.
• If the AM loop antenna wire is covered
with vinyl, remove the vinyl by twisting
it as shown in the diagram.
Speaker cords
(red/black)
Black
1
Red
Blue
Speaker cords
(blue/black)
3
2
Speaker cords
(red/black)
Black
2 Turn the AM loop antenna until you have the
best reception.
To connect an outdoor AM antenna
When reception is poor, connect a single vinyl-covered wire
to the AM EXT terminal and extend it horizontally. The AM
loop antenna must remain connected.
For better reception of both FM and AM
• Make sure the antenna conductors do not touch any other
terminals and connecting cords.
• Keep the antennas away from metallic parts of the unit,
connecting cords, and the AC power cord.
Right speakerLeft speaker
1 Open the speaker terminals on the rear of the
unit.
2 Insert the end of the speaker cord into the
terminal.
Match the polarity (colors) of the speaker terminals: Red
(+) to red (+) and black (–) to black (–); Blue (+) to blue
(+) and black (–) to black (–).
3 Close the speaker terminals.
IMPORTANT: Use only speakers with the same speaker
impedance as indicated by the speaker terminals on the
rear of the unit.
– 7 –
Connecting Other Equipment
Now, you can plug the AC power cord.
You can connect both analog and digital equipment.
• DO NOT connect any equipment while the power
is on.
• DO NOT plug in any equipment until all
connections are complete.
To connect an analog component
Be sure that the plugs of the audio cords are colored: White
plugs and jacks are for left audio signals, and red ones for
right audio signals.
Audio equipment
To audio output
For playing the other equipment through this unit,
connect between the audio output jacks on the other
equipment and AUX jacks by using audio cords (not
supplied).
When connecting the AC power cord into a wall outlet, the
unit automatically starts display demonstration.
IMPORTANT: Be sure to chec k all connections to be done
before plugging the AC power cord into a wall outlet.
Canceling the Display Demonstration
On the unit ONLY:
To cancel the display demonstration, press
CANCEL/DEMO until “DEMO OFF” appears
on the display.
When you press other buttons
The display demonstration stops temporarily. It will start
automatically again (if no operation is done for 2 minutes) unless
you cancel it by pressing CANCEL/DEMO.
To start the display demonstration manually
Press and hold CANCEL/DEMO again for more than 1
second (while Ecology Mode is deactivated).
To connect audio equipment with an optical digital
input terminal
You can record CD sound onto the connected digital
equipment.
CD OPTICAL
DIGITAL OUTPUT
Before connecting the
other equipment,
remove the protective
plug from the terminal.
Audio equipment with
an optical digital input
To optical digital input
Connect an optical digital cord (not supplied) between the
optical digital input terminal on the other equipment and the
CD OPTICAL DIGITAL OUTPUT terminal.
Protective
plug
– 8 –
Loading...
+ 25 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.