JVC CA-MXDK3, CA-MXDK1, CA-MXDK15, CA-MXDK5 User Manual

COMPACT COMPONENT SYSTEM

CA-MXDK5

MX-DK3

—Consists of CA-MXDK3,

SP-MXDK3F and SP-MXDK3W

MX-DK1

—Consists of CA-MXDK1 and

SP-MXDK1F

MX-DK15

—Consists of CA-MXDK15 and

SP-MXDK15F

(For CA-MXDK5) (For CA-MXDK5) (For CA-MXDK5)

(For CA-MXDK5)

INSTRUCTIONS

GVT0177-001A

[US,UN,UG,UX,A,UW]

Warnings, Cautions and Others

Caution–– (standby/on) button!

Disconnect the mains plug to shut the power off completely (the STANDBY lamp goes off). When installing the apparatus, ensure that the plug is easily accessible. The (standby/on) button in any position does not disconnect the mains line.

• When the System is on standby, the STANDBY lamp lights red.

• When the System is turned on, the STANDBY lamp goes off. The power can be remote controlled.

CAUTION

To reduce the risk of electrical shocks, fire, etc.:

1. Do not remove screws, covers or cabinet.

2. Do not expose this appliance to rain or moisture.

CAUTION

• Do not block the ventilation openings or holes. (If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.)

• Do not place any naked flame sources, such as lighted candles, on the apparatus.

• When discarding batteries, environmental problems must be considered and local rules or laws governing the disposal of these batteries must be followed strictly.

• Do not expose this apparatus to rain, moisture, dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

CAUTION

serviceable parts inside the Unit; leave all servicing to qualified service personnel.

CAUTION

3. open. Do not view directly with optical instruments.

: Do not open the top cover. There are no user

: Visible and/or invisible class 1M laser radiation when

G-1

Caution: Proper Ventilation

To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows

1. Front: No obstructions and open spacing.

2. Sides/ Top/ Back: No obstructions should be placed in the areas shown by the dimensions below.

3. Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height

The minimal clearance is shown as below:

Front view Side view

of 10 cm or more.

Wall or obstructions Wall or obstructions

15 cm

CA-MXDK5 CA-MXDK3 CA-MXDK1 CA-MXDK15

15 cm1 cm 1 cm

10 cm

24 kg

CAUTION!

To avoid personal injury or accidentally dropping the unit, have two persons unpack, carry, and install the unit.

MX-DK3

15 cm

CA-MXDK5 CA-MXDK3 CA-MXDK1 CA-MXDK15

Front No obstructions

10 cm

[European Union only]

G-2

Introduction

DIGITAL VIDEO

Precautions

Installation

• Install the System in a location with adequate ventilation to prevent internal heat buildup in the System.

DO NOT install the System in a location near heat sources, or in a place subject to direct sunlight, excessive dust or vibration.

• Install in a place which is level, dry and neither too hot nor too cold—between 5°C and 35°C.

• Leave sufficient distance between the System and the TV.

• Keep the speakers away from the TV to avoid interference with the TV.

Power sources

• When unplugging the System from the wall outlet, always pull on the plug, not the AC power cord.

DO NOT handle the AC power cord with wet hands.

Moisture condensation

Moisture may condense on the lenses inside the System in the following cases:

• After starting to heat the room

• In a damp room

• If the System is brought directly from a cold to a warm place.

Should this occur, the System may malfunction. In this case, leave the System turned on for a few hours until the moisture evaporates, unplug the AC power cord, then plug it in again.

Internal heat

• Make sure there is good ventilation around the unit. Poor ventilation could overheat and damage the unit.

•A cooling fan is inside the System (except for CA-MXDK1 and CA-MXDK15) to prevent heat buildup.

DO NOT block the ventilation openings or holes. If they are blocked by a newspaper or cloth, etc., the heat may not be able to get out.

Others

• Should any metallic object or liquid fall into the System, unplug the AC power cord and consult your dealer before operating any further.

DO NOT disassemble the System since there are no user serviceable parts inside.

• If you are not going to operate the System for an extended period of time, unplug the AC power cord from the wall outlet.

If anything goes wrong, unplug the AC power cord and consult your dealer.

Playable Disc Types

* *

COMPACT

DIGITAL AUDIO

DVD Logo is a trademark of DVD Format/Logo Licensing Corporation.

• CD-R/-RW/-ROM: Recorded in the Audio CD, Video CD and SVCD formats. MP3, WMA, JPEG, MPEG-1, MPEG-2, ASF* and DivX* files written in accordance with the “ISO 9660” format can also be played.

• DVD-R/-RW: Recorded in the DVD Video format or the DVD Video Recording (VR) format. MP3, WMA, JPEG, MPEG-1, MPEG-2, ASF* and DivX* files written in the UDF format can also be played.

* CA-MXDK5 only

In addition to the above discs, this System can play back audio data recorded on CD Text, and CD-Extra.

• It is possible to play back finalized +R/+RW (DVD Video Format only) discs. “DVD” lights on the front display panel when a +R/+RW disc is loaded.

• The following discs cannot be played back: DVD-ROM, DVD-RAM, CD-I (CD-I Ready), CD-G (CD Graphics), Photo CD, etc. Playing back these discs will generate noise and damage the speakers.

• For MX-DK3 and MX-DK1/MX-DK15: This unit cannot play back DVD-VR discs with CPRM (Content Protection for Recordable Media).

• In this manual, “file” and “track” are interchangeably used for MP3/WMA/MPEG-1/MPEG-2/ASF/DivX/JPEG operations.

About color system

This System accommodates both NTSC and PAL system and can play back discs recorded with either system. To change the color system, see page 6.

Note on Region Code

DVD players and DVDs have their own Region Code numbers. This System can play back only DVDs with Region Code numbers including “4” for Australia and Central and South America, “3” for Southeast Asia, and “2” for the Middle East. For your available Region code, check the rear panel of your main unit. EX.: For Southeast Asia

If a DVD with the improper Region Code numbers is loaded, “REGION ERR” appears on the display and playback will not start.

INFO

The System can play back the following digital audio formats.

•

LPCM

(Linear PCM),

(Digital Theater Systems),

DTS

Packing)

Caution for DualDisc playback

The Non-DVD side of a “DualDisc” does not comply with the “Compact Disc Digital Audio” standard. Therefore, the use of Non-DVD side of a DualDisc on this product may not be recommended.

IMPORTANT: Before playing a disc, make sure of the following...

• Turn on the TV and select an appropriate input mode on the TV to view the pictures or on-screen displays on the TV screen.

• For disc playback, you can change the initial setting to your preference. See “Setup Menu Operations” on page 34.

If “ ” appears on the TV screen when you press a button,

tried to do, or data required for that operation is not recorded on the disc.

the disc cannot perform the operation you have

DIGITAL

MLP

(Dolby Digital),

(Meridian Lossless

How to Read This Manual

• Button and control operations are explained in the table below.

•

Some related tips and notes are explained later in the sections “Learning More about This System” and “Troubleshooting,” but not in the same section explaining the operations ( indicates that the content has some information).

Indicates that you press the button

and repeatedly

selected.

Indicates that you press one of the buttons.

2 sec.

Remote ONLY

Main Unit

ONLY

Indicates that you for a specified period. The number inside the arrow indicates the time to hold (in the example, 2 seconds).

Indicates that you turn the control toward the specified direction(s).

Indicates that this operation is only possible using the remote control.

Indicates that this operation is only possible using the buttons and controls on the main unit.

INFO

briefly

until an option you want is

press and hold

the button

Contents

Connections .............................................................3

Preparing the Remote Control ............................................ 6

Changing the Color System and Scanning Mode .............. 6

Canceling the Demonstration ............................................. 6

Display Indication ...................................................7

Daily Operations—Playback .................................8

Daily Operations—Sound & Other Adjustments ... 12

Reinforcing the Bass Sound ............................................. 12

Presetting Automatic DVD Video Sound

Increase Level .............................................................. 12

Creating 3-dimensional Sound Field—3D Phonic ........... 13

Selecting the Sound Modes .............................................. 13

Creating Your Own Sound Modes—User Mode ............. 13

Changing the Picture Tone ............................................... 14

Changing the Display Brightness ..................................... 14

Setting the Clock .............................................................. 14

Unique DVD/VCD Operations ............................15

Selecting the Sound Track ................................................ 15

Selecting the Subtitle Language........................................ 16

Selecting the View Angle ................................................. 16

Selecting Browsable Still Pictures (CA-MXDK5 only) ... 16

Playing Back a Bonus Group (CA-MXDK5 only) ........... 17

Special Picture Playback................................................... 17

Advanced Disc Operations ...................................18

Programming the Playing Order—Program Play ............ 18

Playing at Random—Random Play ................................. 19

Playing Repeatedly .......................................................... 20

Prohibiting Disc Ejection—Child Lock ........................... 20

On-Screen Disc Operations .................................. 21

Recording Operations ..........................................26

Enjoying Karaoke .................................................28

Singing Along (Karaoke) .................................................. 28

Singing Along Using Stereo Discs—Vocal Masking ....... 29

Microphone Mixing .......................................................... 30

Reserving Karaoke Songs—Karaoke Program Play......... 31

Timer Operations ..................................................32

Setup Menu Operations .......................................34

Operating the TV ..................................................36

Additional Information ........................................37

Learning More about This System ................................... 37

Troubleshooting ............................................................... 40

Maintenance ..................................................................... 41

Specifications ................................................................... 42

Parts Index ............................................................44

Connections

Do not connect the AC power cord until all other connections have been made.

• Connect VIDEO OUT directly to the video input of your TV. Connecting VIDEO OUT to a TV via a VCR may cause a monitor problem when playing back a copy-protected disc. You may also have a monitor problem when connecting the player to an integrated TV/Video system.

~ From AM/FM antenna

See page 4.

Ÿ From the video input of TV/monitor

See page 4.

! From the digital input of digital audio

component such as CD recorder, etc.

See page 4.

Supplied Accessories

• FM antenna (1)

• AM loop antenna (1)

• Composite video cord (1)

• Remote control (1)

• Batteries (2)

• AC plug adaptor (1) (not supplied for the Middle East and Australia)

If any item is missing, consult your dealer immediately.

⁄ From auxiliary equipment

See page 4.

@ From subwoofers (CA-MXDK5 and

MX-DK3)

See page 5.

¤ From surround speakers

See page 5.

# From main speakers

See page 5.

‹ Voltage Selector

Before plugging in, confirm the position the voltage selector points to. See page 6 and the back cover.

$ To a wall outlet

Plug in the AC power cord only after all connections are complete.

• Before plugging in, confirm the position the voltage selector points to. See page 6 and the back cover.

• If the wall outlet does not match the AC plug, use the supplied AC plug adaptor (not supplied for the Middle East and Australia).

* The illustration above is for CA-MXDK5.

AM/FM antenna

To assemble the AM loop antenna

TV/monitor

Green

Blue

Red

To connect AM/FM antenna

FM antenna (supplied)

Extend it so that you can obtain the best reception.

AM loop antenna (supplied)

Turn it until the best reception is obtained.

For better AM/FM reception

FM outdoor antenna (not supplied)

AM loop antenna (supplied)

Keep it connected.

Vinyl-covered wire (not supplied)

Extend it horizontally.

• Disconnect the supplied FM antenna, and connect to an outdoor FM antenna using a 75 connector (IEC or DIN45325).

• Make sure the antenna conductors do not touch any other terminals, connecting cords or the power cord. Also, keep the antennas away from metallic parts of the System, connecting cords, and the AC power cord. This could cause poor reception.

Ω

wire with coaxial type

Component video cord (not supplied)

S-video cord (not supplied)

• Connect the VIDEO jack, S-VIDEO jack, or COMPONENT jacks (CA-MXDK5 only) whichever you want to use.

• To select progressive scanning mode (see page 6), use COMPONENT jacks (CA-MXDK5 only).

• To select the video output to match the color system of your TV (PAL or NTSC), see page 6.

Digital audio component

Protective cap

• Set “DIGITAL AUDIO OUTPUT” in the “AUDIO” preference display correctly according to the connected digital audio equipment (see page 35). If setting is incorrect, loud noise may be generated causing damage to the speakers.

Digital audio signals are output from this System only when “DVD/CD” is selected as the source.

⁄

Auxiliary equipment

Red

Stereo audio cord

(not supplied)

Composite video cord (supplied)

White

Continued on the next page...

For the Australian model

Stereo mini plug

(not supplied)

Subwoofers (for CA-MXDK5 and MX-DK3)

• MX-DK3 has only one subwoofer.

• When connecting the speaker cords, match the polarity of the speaker terminals: (+) to (+) and (–) to (–).

CA-MXDK5

Surround speakers (for CA-MXDK5 and

MX-DK3)

From right surround speaker (not supplied)

From left surround speaker (not supplied)

• The surround speakers connected can reproduce the bass sounds recorded in front left and right channels, but cannot reproduce the surround signals recorded in DVD multichannel discs.

Main speakers

• When connecting the speaker cords, match the polarity of the speaker terminals: (+) to (+) and (–) to (–).

From right

subwoofer

MX-DK3

From the subwoofer

• Use only speakers with the same speaker impedance as indicated by the speaker terminals on the rear of the unit.

From left subwoofer

From right

main speaker

•

Use only speakers with the same speaker impedance as indicated by the speaker terminals on the rear of the unit

• The speakers are magnetically shielded to avoid color distortions on TVs. However, if not installed properly, it may cause color distortions. So, pay attention to the following when installing the speakers. – When placing the speakers near a TV set, turn off the TV’s

main power switch or unplug it before installing the speakers. Then wait at least 30 minutes before turning on the TV’s

main power switch again. Some TVs may still be affected even though you have followed the above. If this happens, move the speakers away from the TV.

• DO NOT connect more than one speaker to each terminal.

• DO NOT push or pull the speakers as this will damage the foot spacers at the bottom of the speakers.

From left main speaker

‹

Voltage Selector

Use a screwdriver to rotate the voltage selector so that the voltage mark is pointing to the same voltage as where you are plugging in the unit. (See also the back cover page.)

When your mains lead (AC) line voltage is 230-240V

When your mains lead (AC) line voltage is 220 V

• Dispose of batteries in the proper manner, according to federal, state, and local regulations.

When using the remote control

Point the top of the remote control toward the remote sensor as directly as possible. If you operate it from a diagonal position, the operating range (approx. 5 m) may be shorter.

Changing the Color System and

Remote

Scanning Mode

You can select the video output to match the color system of your TV (PAL or NTSC). Also, CA-MXDK5 supports progressive scanning. If you connect a progressive TV through the COMPONENT jacks, you can enjoy a high quality picture from the built-in DVD player by selecting “PAL/NTSC PRG.”

Enter the color system setting mode.

ONLY

INFO

Voltage mark

When your mains lead (AC) line voltage is 110V

Voltage mark

DO NOT plug in before setting the voltage selector on the rear of the unit and all connection procedures are complete.

Voltage mark

When your mains lead (AC) line voltage is 127 V

Preparing the Remote Control

Voltage mark

(While holding...)

Select the color system and scanning mode.

PAL PRG*PAL

NTSC PRG* NTSC

PAL/NTSC

PAL/NTSC PRG

* Only for CA-MXDK5. PROGRESSIVE indicator lights on

when progressive mode is selected.

Store the setting.

Canceling the Demonstration

Interlaced scanning. For a conventional TV.

* Progressive scanning.

For a progressive TV.

Main Unit

ONLY

R6(SUM-3)/AA(15F)

DO NOT recharge, short, disassemble, heat the battery or dispose of it in a fire.

When you plug in the AC power cord to a wall outlet, the System automatically starts the display demonstration.

2 sec.

DEMO OFF

DEMO START

To start the demonstration

, select DEMO START.

Display Indication

The indications on the display tell you a lot of things while you are operating the System.

Before operating the System, be familiar with when and how the indicator illuminates on the display.

PROGRESSIVE indicator (CA-MXDK5 only)

• Lights when the progressive scanning mode is selected (see page 6).

BONUS indicator (CA-MXDK5 only)

• Lights when DVD Audio with bonus group is detected (see page 17).

DVD LEV. 1/2/3 indicators

• Lights to indicate the DVD increase level

MIC indicator

• Lights when the Karaoke mode is activated (see page 28).

3D PHONIC indicator

• Lights when 3D Phonic is activated (see page 13).

V.MASK indicator

• Lights when the Vocal Masking mode is activated (see page 29).

RESUME indicator

• Lights when the Resume function is activated (see page 10).

SOUND TURBO indicator

• Lights when SOUND TURBO is activated (see page 12).

SURROUND indicator

• Lights when Surround mode is activated (see page 13).

Timer indicators (see pages 32 and 33)

• SLEEP: flashes when the Sleep Timer is activated.

• DAILY: lights when the Daily Timer is on standby; flashes while working or being set.

• REC: lights when the Recording Timer is on standby; flashes while working or being set.

•: lights when Sleep Timer is working or when Daily Timer or Recording Timer is on standby, working or being set.

(see page 12)

Source signal indicators

• D: lights when a source signal is Dolby Digital.

• DTS: lights when a source signal is DTS.

Tape operation indicators

• REC: lights while recording (see pages 26 and 27).

• TAPE: lights when a tape is loaded in either deck A or deck B.

• A: lights when a tape is loaded in the deck A.

• B: lights when a tape is loaded in the deck B.

•

2 3

(tape direction): – Lights to indicate the current tape running direction. – Flashes slowly during playback and recording. – Flashes quickly while rewinding a tape.

Main display

MP3 indicator

• Lights while playing back an MP3 track.

WMA indicator

• Lights while playing back a WMA track.

Disc operation indicators

• REP: lights when Repeat Play mode is activated.

• 1: lights when One Track/Chapter/Step Repeat is activated.

PRGM indicator

• Lights when Program Play mode is activated.

RND indicator

• Lights when Random Play is activated.

B.S.P. indicator (CA-MXDK5 only)

• Lights when browsable still picture on DVD Audio is available (see page 16).

;

ST (stereo) indicator

• Lights while an FM stereo station with sufficient signal strength is tuned in (see page 9).

MONO indicator

• Lights while receiving an FM stereo station in monaural (see page 9).

Daily Operations

In this manual, the operations using the remote control are mainly explained; however, you can use the buttons and controls on the main unit if they have the same (or similar) name and marks.

Number

buttons

RETURN

TOP MENU

, , ,

ENTER/SET

PREV.,NEXT

4,¢

TITLE/GROUP

SHIFT

FM MODE

7,8

1,¡

FADE MUTING

—Playback

Turn on the power.

The STANDBY lamp on the main unit goes off.

• Without pressing AUDIO, the System also turns on by pressing one of the source select buttons in the next step.

Select the source.

Playback automatically starts if the selected source is ready to start playback.

• If you press AUX, start playback on the external component.

Adjust the volume.

[

Operate the target source as explained later.

To turn off (standby) the System

The STANDBY lamp on the main unit lights in red.

•A small amount of power is always consumed even while on standby.

For private listening

Connect a pair of headphones to the PHONES jack on the main unit. The sound will no longer come out of the speakers.

connecting or putting on the headphones.

• Disconnecting the headphones will activate the

Be sure to turn down the volume before

speakers again.

DO NOT turn off (standby) the System with the volume set to an extremely high level; otherwise, the sudden blast of sound can damage your hearing, speakers and/or headphones when you turn on the System or start playback.

Adjusting the Volume

The volume level can be adjusted in 32 steps (VOLUME MIN, VOLUME 1 – VOLUME 30, and VOLUME MAX).

Remote control:

Main unit:

Continued on the next page...

Remote

To drop the volume in a moment

To restore the volume,

ONLY

press again, or

adjust the volume level.

Listening to the Radio

To select the AM tuner interval spacing

Main Unit

ONLY

INFO

Some countries space AM stations 9 kHz apart, and other countries use 10 kHz spacing.

Select AM.

Select the appropriate AM space interval for your

area.

(10 kHz interval)

If the FM station has poor reception

The MONO indicator lights on the display. Reception will improve though stereo effect is lost—monaural reception mode.

To restore the stereo effect,

button again (the MONO indicator goes off).

Remote

To preset stations

ONLY

You can preset 30 FM and 15 AM stations.

Tune in to a station you want to preset.

Select a preset number.

press the

(While holding...)

(9 kHz interval)

To select the band (FM/AM)

FM AM

Remote

To tune in to a station

While FM or AM is selected...

1 sec.

Frequency starts changing on the display. When a station (frequency) with sufficient signal strength is tuned in, the frequency search stops.

• When you repeatedly press the button, the frequency changes step by step.

To stop searching manually,

ONLY

Increases the frequencies.

Decreases the frequencies.

press either button.

Store the station.

To tune in to a preset station

Select the band (FM or AM).

FM AM

Select the preset number for the preset station.

Examples:

To select number 5, press 5. To select number 10, press 10. To select number 15, press h 1, then 5. To select number 30, press h 3, then 0.

• You can also use 1

or ¡

buttons.

10,

Playing Back a Disc

INFO

Before operating a disc, be familiar how a disc is recorded.

• DVD Video/DVD-VR consist of “ “

Chapters

ASF*/DivX* consist of “ “

Tracks Files

“

,” DVD Audio/MP3/WMA/MPEG-1/MPEG-2/

Groups

,” JPEG consist of “

,” and CD/SVCD/VCD consist of only “

Titles

” which include

Groups

” which include

Tracks

.”

• For DVD-VR/MP3/WMA/MPEG-1/MPEG-2/ASF*/ DivX*/JPEG playback, see also “Operations on the Control Screen” on page 24.

* Only for CA-MXDK5.

To insert discs

• When using an 8 cm disc, place it on the inner circle of the disc tray.

While playing a disc except CDs:

This System can store the

stop point, and when you start playback again by pressing DVD/CD 3

(even while on standby), it starts from the position where you have stopped—Resume Play. (RESUME appears on the display when you stop playback.)

press 7

To stop completely while Resume is activated,

twice. (To cancel Resume, see “RESUME” on page 35.)

Remote

To select a title/group

ONLY

While playing a disc...

Examples:

To select number 5, press 5. To select number 10, press 10. To select number 15, press h

10, 1, then 5.

To select number 30, press h

10, 3, then 0.

To select a chapter/track

While playing a disc...

To close the disc tray,

If you press DVD/CD 3

press OPEN/CLOSE 0

again.

, disc tray closes automatically and

playback starts.

To start:

To pause: To stop:

To release it, press DVD/CD 3

On-screen guide icons

• During disc playback, the following icons may appear for a while on the TV screen:

Appears at the beginning of a scene containing multi-angle views.

Appears at the beginning of a scene containing multi-audio languages.

Appears at the beginning of a scene containing multi-subtitle languages.

• The following icons will be also shown on the TV screen to indicate your current operation.

, , , , ,

• To deactivate the on-screen guide icons, see “ON SCREEN GUIDE” on page 35.

Remote

To locate a particular portion

ONLY

While playing a disc except for MP3/WMA/DivX...

While playing a DivX disc (CA-MXDK5 only)...

• For MP3/WMA/DivX (CA-MXDK5 only) discs, search speed and the indications on the TV are different.

• No sound comes out while searching on DVD Video/ SVCD/VCD.

To return to normal playback,

press DVD/CD 3

• CA-MXDK5 only: For DivX discs, each time you press the

or button, you can skip to a scene 30 seconds or

5 minutes before or after depending on the DivX file.

Remote

(While holding...)

o select

You can select a title/chapter/track directly and start playback. For DVD Video, you can select

playback playback

an item directly

, while you can select .

Examples:

To select number 5, press 5. To select number 10, press 10. To select number 15, press h 1, then 5. To select number 30, press h 3, then 0.

To play back using the disc menu

You can operate the disc play—DVD and SVCD/VCD with Playback Control (PBC)—using the disc menu shown on the TV screen.

For DVD Video/DVD Audio (CA-MXDK5 only):

Show the disc menu.

Select an item on the disc menu.

ONLY

a title before starting

a chapter after starting

10,

Remote

ONLY

To move to the next or previous page of the current menu:

To cancel PBC

Before playback...

You can also cancel PBC function by pressing the number button to select a track.

To reactivate PBC,

press 4

To return to the previous menu:

Playing Back a Tape

To insert a tape

You can play back type I tapes.

• The use of C-120 or longer tapes is not recommended.

• With some discs, you can also select items by entering the number using the number buttons.

For SVCD/VCD with PBC:

While playing a disc with PBC, “PBC” appears on the display instead of the playing time. When disc menu appears on the TV screen, select an item on the menu. Playback of the selected item starts.

Examples:

To select number 5, press 5. To select number 10, press 10. To select number 15, press h 1, then 5. To select number 30, press h 3, then 0.

Push Insert and close

To start: To stop: To fast-forward or

rewind:

10,

Daily Operations

—Sound & Other Adjustments

Remote Control

VFP

, , ,

ENTER/SET

DVD LEVEL

SHIFT

AHB LEVEL

*MX-DK1/

DVD LEVEL+,

–

MX-DK15

AHB

–

Reinforcing the Bass Sound

To change the bass level

For CA-MXDK5 and MX-DK3

ACTIVBASS 0 1 2

DIMMER CLOCK/

DISPLAY

• You can also use ACTIVE BASS EXTENSION +/– on the main unit.

For MX-DK1 and MX-DK15

SOUND MODE 3D PHONIC

SOUND TURBO

• You can also use ACTIVE BASS EXTENSION on the main unit.

To reinforce the heavy sound—SOUND TURBO

You can boost the low and high frequency sound.

A.BASS ON

A.BASS OFF

Main unit

*MX-DK1/

MX-DK15

SOUND TURBO

ACTIVE BASS EXTENSION –,

DVD LEVEL

3D PHONIC SOUND MODE

DVD LEVEL –,

ACTIVE BASS EXTENSION

Presetting Automatic DVD Video Sound Increase Level

The DVD Video sound is sometimes recorded at a lower level than other discs and sources. You can set the increase level for the currently loaded DVD Video, so you do not have to adjust the volume when you change the source.

For CA-MXDK5 and MX-DK3

DVD LEVEL2DVD LEVEL1

DVD LEVEL3

For MX-DK1 and MX-DK15

32DVD LEVEL1

As the number increases, sound level also increases.

+ 33 hidden pages