JVC AV-29VT11/P, AV-29VT11/T, AV-29VT31/P User Manual

COLOR TELEVISION

INSTRUCTIONS

Thank you for buying this JVC color television. To make sure you understand how to use your new TV, please read this manual thoroughly before you begin.

AV-21VT11 AV-21VT31 AV-21WA11 AV-25VT11 AV-25VT31 AV-29VT11 AV-29VT31

GGT0018-001A-H 0503-NIC-JMT

Safety precautions

WARNING

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION

TO ENSURE PERSONAL SAFETY, OBSERVE THE FOLLOWING RULES REGARDING THE USE OF THIS TV.

• Operate only from the power source specified on the TV.

• Avoid damaging the power cord and mains plug. When you unplug the TV, pull it out by the mains plug. Do not pull on the power cord.

• Never block or cover the cabinet openings for ventilation. Never install the TV where good ventilation is unattainable. When installing this TV, leave spaces for ventilation around the TV more than the minimum distances shown in the diagram.

• Do not allow objects or liquid into the cabinet openings.

• In the event of a fault, unplug the TV and bring to JVC service centre. Do not attempt to repair it by yourself or remove the rear cover.

• The surface of the TV screen is easily damaged. Be very careful with it when handling the TV. Should the TV screen become soiled, wipe it with a soft dry cloth. Never rub it forcefully. Never use any cleaner or detergent on it.

• When you don’t use this TV for a long period of time, be sure to disconnect the power plug from the AC outlet.

• The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

10 cm

15 cm

15 cm10 cm

WARNING

<AV-21WA11 only>

A removable plastic cover is fixed to the television’s front Audio/Video connector. To prevent this cover from being accidentally swallowed by babies or children, remove it from the television and store it in a safe place. If the cover is swallowed seek the advice of a doctor immediately.

<AV-21VT31/AV-25VT31/AV-29VT31 only>

The Twin Port Bass Blaster Unit is packaged together with the TV. Before you use the TV, mount the Twin Port Bass Blaster Unit correctly on the TV.

2

Preparation

1 Confirm which remote control you have

Your TV comes with one of the two remote controls shown below. Functions you can operate differ depending on the type of remote control.

<RM-C1330> <RM-C1331>

For TV model:

AV-21VT31, AV-25VT31,

AV-29VT31

For TV model:

AV-21VT11, AV-21WA11,

AV-25VT11, AV-29VT11

MUTING

COLOR

SYSTEM

DISPLAY

CLOSED

CAPTION

TV/VIDEO

OFF

TIMER

PICTURE

MODE

CHANNEL

SCAN

CHANNEL

POWER

CINEMA

SURROUND

BASS

MENU

ECO

SENSOR

123

456

789

RETURN+

FAVORITE CH

RM-C1330

100+

0

VOLUME

TV

MUTING

COLOR

SYSTEM

DISPLAY

CLOSED

CAPTION

TV/VIDEO

OFF

TIMER

PICTURE

MODE

CHANNEL

SCAN

CHANNEL

RETURN+

POWER

CINEMA

SURROUND

ECO

SENSOR

MENU

123

456

789

100+

0

VOLUME

FAVORITE CH

RM-C1331

TV

2 Insert the batteries into the remote control

Correctly insert two batteries, observing the , and polarities and inserting the . end first.

CAUTION:

Follow the cautions printed on the batteries.

Notes:

• Use AA/R6/UM-3 dry cell batteries.

• If the remote control does not work properly, replace with new batteries. The supplied batteries are for testing, not regular use.

.

3

Preparation

3 Connecting the antenna and VCR

• Read the manuals provided with the devices. Depending on the device, the connection method may be different from the diagrams. Also the device settings may need to change depending on the connection method.

• Turn off all the devices including the TV.

• Connecting cables are not supplied.

• When connecting monaural audio to the TV, use the L/MONO jack.

• You can connect an S-VIDEO compatible device (such as an S-VHS VCR) to the S-connector with an S-VIDEO cable and enjoy the high quality picture of the S-VIDEO signal (Y/C signal). In that case, do not connect it to the TV with a video cable.

Connecting the antenna

COMPONENT

VIDEO-1

(

)

VIDEO-2

INPUT

S

OVER

V

L

/

R

MONO

OUTPUT

INPUT

Y

V

/

V

C

B

L

/

MONO

R

C

R

Connecting the antenna and VCR

3

To video output

To audio output

Matching aerial adapter (supplied)

To RF output

VHF/UHF outdoor antenna

COMPONENT

VIDEO-1

(

)

OUTPUT

VIDEO-2

INPUT

S

OVER

Y

V

L

/

MONO

RRRC

V

/

V

L

C

B

/

MONO

R

(1)

(2)

(3)

VHF/UHF outdoor aerial

2

To S-video output

VCR

To aerial input

1

4

Preparation

4 Connecting other devices

If you are not connecting any other devices, skip step 4 and perform step 5.

• Use the headphones with a stereo mini jack (3.5 mm in diameter). When you connect the headphones, the TV speakers go off.

• The OUTPUT terminal outputs the video and sound signals which you are viewing on the TV. You can dub them onto the VCR connected to the OUTPUT terminal. (The OUTPUT terminal cannot output S-VIDEO signals or component video signals. Also it cannot output any signals when the TV is turned off.)

• Connect components outputting a component signal (Y/C the VIDEO-2 terminal, and set VIDEO-2 SET function to “COMPONENT”. (See page 14.)

• The following illustrations are for the AV-21VT11/AV-21VT31/AV-25VT11/AV-25VT31. Your TV’s front and rear pannels may not look exactly like the illustrations.

B/CR signal), such as a DVD player, to

Front

Headphones

Rear

COMPONENT

VIDEO-1

INPUT

S

OVER

V

Y

/

V

C

B

L

/

MONO

RRR

R

(

VIDEO-2

INPUT

L

)

/

MONO

OUTPUT

V

L

RC

Camcorder or TV game

VCR (for playing) DVD player

(composite signals)

VCR (for recording)

DVD player

(component video signals)

5 Connect the power cord to the AC outlet

Operate only from the power source indicated on the rear of the TV.

5

Preparation

6 SETUP TOUR

When the TV is first turned on it enters the SETUP TOUR mode, and the JVC logo is displayed. Follow the instructions on the on-screen display to perform the SETUP TOUR.

• In case of resetting that the reason for such as removal, you can set the AUTO CH PRESET function on the “MENU 3” menu. For details, see page 14.

1 Press the Main power button

on the TV.

The POWER lamp lights. After the JVC logo has been displayed, the TV automatically switches to the language setting mode.

SETUP TOUR

2 Press the CHANNEL –/+ or the

/

MENU

buttons to select

the on-screen language.

SETUP TOUR

LANGUAGE

ENGLISH

EXIT BY

DISPLAY

3 Press the CHANNEL –/+ or the

/

MENU

buttons to select the tuner mode (AIR or CABLE).

SETUP TOUR

TUNER MODE

AIR

OPERATE BY -+

DISPLAY

4 The AUTO PROGRAMMING

function will start and the indicator blinks.

SETUP TOUR

POWER lamp

SYSTEM

DISPLAY

button

MENU

buttons

CHANNEL –/+ buttons

DISPLAY

CLOSED

/

TV/VIDEO

PICTURE

CHANNEL

•To stop the AUTO PROGRAMMING function, press the CHANNEL m or the MENU / buttons.

When all the TV channels that can be received on your TV have been preset, the display goes out and the AUTO PROGRAMMING function operation is completed.

5 Upon the completion of

AUTO PROGRAMMING function, the message below is displayed.

COLOR

BASS

CAPTION

OFF

TIMER

MODE

RETURN+ 100+

SCAN

CHANNEL

SETUP TOUR

Main power button

CINEMA

SURROUND

ECO

SENSOR

MENU

123

456

789

0

VOLUME

MENU t

buttons

NOW PROGRAMMING

STOP BY

-+

THANK YOU!

SET IS NOW COMPLETE

6

Basic operation

• The illustration below is for the remote control RM-C1330 supplied with VT31 series models. Your remote control may not look exactly like the illustrations.

SURROUND

MENU

CINEMA

0

VOLUME

POWER

ECO

SENSOR

100+

MUTING

COLOR

SYSTEM

DISPLAY

CLOSED CAPTION

TV/VIDEO

OFF

TIMER

PICTURE

MODE

CHANNEL

SCAN

CHANNEL

RETURN+

BASS

123

456

789

FAVORITE CH

RM-C1330

TV

1 Press the POWER button to turn

your TV on.

• If your TV does not turn on, press the Main power button on the TV then press the POWER button again.

• You can also turn on your TV by pressing any of the following buttons;

- the CHANNEL m button

- the Number buttons

- the TV/VIDEO button

2 Select a channel.

■ Press the CHANNEL m button.

• Up/down selection cannot be selected for channels to which the CHANNEL SKIP function has been set to “YES”. See page 15.

■ Press the Number buttons to enter the channel number.

• When you want to select a channel

number over 100, enter the two-digit number after pressing the 100+ button.

3 Press the VOLUME M button to

adjust the sound.

4 To turn your TV off, press the

POWER button.

• We recommend that you press the Main

power button on the TV to turn the main power off if you do not plan to use your TV for a long time or if you wish to save energy.

Viewing Images from an External Device:

Press the TV/VIDEO button to select the VIDEO mode.

• You can also use the INPUT function to select the VIDEO mode. For details, refer to page 12.

If the picture is not clear:

Press the COLOR SYSTEM button to select another color system, see page 8.

• Color system cannot be changed in TV mode.

7

Remote control buttons and functions

MUTING button

You can turn the sound off instantly.

Press this button.

To turn the sound on, press this button again.

COLOR SYSTEM button

If the picture is not clear or no color appears, change the current color system to another color system.

Press this button to select the color system.

In TV mode:

NTSC 3.58 (Fixed)

In VIDEO mode:

AUTO

PAL

NTSC3.58

NTSC4.43

AUTO:

Automatic color system selection

• If the picture is abnormal in the AUTO mode, change the AUTO mode to another color system.

• Only in VIDEO mode, “COLOR SYSTEM” is displayed in MENU 2 and can be changed.

BASS button

<AV-21VT31/AV-25VT31/AV-29VT31 only>

You can enjoy a powerful bass sound by using the SUPER BASS (Bass Reflex) function.

Press this button to turn the SUPER BASS function on or off.

• To use this function, you must first mount the Twin Port Bass Blaster Unit packaged with the TV on top of the TV. For details, see page 19.

CINEMA SURROUND button

You can enjoy an enhanced sound for a wider audience by using CINEMA SURROUND function.

Press this button to select one of the CINEMA SURROUND mode.

HIGH/LOW:

When you listen to the stereo sound, please select HIGH mode or LOW mode. You can enjoy the sound for a wider audience similar to the experience at the theatre.

• In case that you setting up the CINEMA SURROUND function to HIGH mode, there may be slight volume distortion. In case that occurs, please switch the HIGH mode to LOW mode, the effect of CINEMA SURROUND functions will be less noticeable, however, the volume distortion will be corrected.

MONO SURROUND:

Select the MONO SURROUND mode, when you listen to the mono sound. You can enjoy the sound for a wider audience similar to stereo sound.

OFF:

The CINEMA SURROUND function switches off.

DISPLAY button

You can continuously display the current channel number or VIDEO mode on the screen.

Press this button.

To turn the display off, press this button again.

• When selecting a VIDEO mode with no signal, indication of the VIDEO mode becomes fixed on the screen.

8

Remote control buttons and functions

ECO SENSOR button

You can adjust this TV so that the screen automatically adjusts to the optimum contrast according to the brightness of your room. This function reduces eye strain and the power consumption of this TV.

Press this button to select the desired mode.

AI ECO SENSOR 1:

The AI ECO SENSOR function switches on. Usually, it is recommended to watch the TV in this mode.

AI ECO SENSOR 2:

The AI ECO SENSOR function switches on. If you feel the screen in the “AI ECO SENSOR 1” mode is too dark, select this mode.

AI ECO SENSOR OFF:

The AI ECO SENSOR function switches off.

• You can display on the screen the effect of the AI ECO SENSOR function. For details, see “AI ECO DISPLAY” on page 18.

CLOSED CAPTION button

If they are included in a program, you can view closed captions or text information.

Press this button to select the mode.

OFF CLOSED CAPTION TEXT

• To change caption or text channels see page 13.

OFF TIMER button

You can set the TV to automatically turn off after a set time.

Press this button to select the period of time.

• You can set the period of time to a maximum of 120 minutes in 10 minute increments.

• 1 minute before the OFF TIMER function turns off the TV, “GOOD NIGHT!” appears.

To display the remaining time, press this button once.

To cancel the OFF TIMER function, press this button to set the period of time to 0.

• The OFF TIMER function will not turn off the TV’s main power.

PICTURE MODE button

You can select one of three picture adjustment settings as you like.

Press this button to select a mode.

BRIGHT:

Heightens contrast and sharpness.

STANDARD:

Standardizes picture adjustments.

SOFT:

Softens contrast and sharpness.

• Pressing this button returns all the picture settings in “MENU 4” to their default settings.

9

Remote control buttons and functions

CHANNEL SCAN button

You can quickly view all TV channels programs that you can view on your TV, and search for the program you want to view.

1 Press this button to start scanning

TV channels.

The TV channel programs are each displayed for several seconds.

• The programs of TV channels for which the CHANNEL SKIP function is set to “YES” are not displayed.

2 When you find the program you

want to view, press this button again to stop scanning.

FAVORITE CH button

When tuner mode is AIR, you can correlate 4 channels out of 68 channels (CH02-CH69) with FAVORITE CH buttons RED, GREEN, YELLOW and BLUE.

When tuner mode is CABLE, you can correlate 4 channels out of 125 channels (CH01-CH125) with FAVORITE CH buttons RED, GREEN, YELLOW and BLUE.

Press one of the FAVORITE CH buttons for more than 3 seconds to correlate currently watching channel. After the channel and button are correlated, you can directly select favorite channel by the correlated button.

• When MENU is displayed, FAVORITE CH cannot be correlated.

• Correlation of FAVORITE CH button and the channel cannot be reset eventhough the main power is turned off.

• After tuner mode is changed by AUTO CH PRESET, FAVORITE CHANNELS are reset to default setting.

Default setting:

RED................CH02

GREEN............CH03

YELLOW..........CH04

BLUE...............CH05

Please refer to AUTO CH PRESET on page 14.

RETURN + button

You can set a channel you frequently view to the Return Channel and you can view that channel at any time with one-touch.

To set the channel to the Return Channel:

1 Select the channel you want to set

to the Return Channel.

2 Press this button and hold until the

message “RETURN PLUS PROGRAMMED!” appears.

• When you turn off the TV, the Return Channel setting is cancelled.

To view the Return Channel:

Press this button.

• You can view two channels (current channel and Return Channel) alternately by pressing this button.

To cancel the Return Channel setting:

Press this button and hold until the message“RETURN PLUS CANCELLED!” appears.

If no channel is set to the Return Channel:

You can view the channel selected right before the current channel by pressing this button.

10

Using the TV’s menus

This TV has a number of functions you can operate using the menus. To use all your TV’s functions fully, you need to understand how to use the menus.

DISPLAY

button

MENU

buttons

CHANNEL –/+ buttons

COLOR

SYSTEM

DISPLAY

CLOSED

/

CAPTION

TV/VIDEO

TIMER

PICTURE

MODE

CHANNEL

SCAN

BASS

MENU

123

OFF

456

789

RETURN+ 100+

CHANNEL

CINEMA

SURROUND

0

VOLUME

ECO

SENSOR

MENU t

buttons

■ Basic operation

1 Press the MENU T buttons.

One of the 6 menus is displayed.

MENU number

The icon on the left indicates the currently selected function.

MENU 1 INPUT TV VNR ON COMPRESS(16:9) ON

CLOSED CAPTION PICTURE TILT 00

SELECT BY EXIT BY OPERATE BY -+

DISPLAY

4 Press the CHANNEL –/+ or the

/

MENU

buttons to change

function settings.

Example:

MENU 2 AUTO SHUTOFF OFF CHILD LOCK OFF BLUE BACK ON VIDEO-2 SET COMPONENT

SELECT BY EXIT BY OPERATE BY -+

• With some functions, the operation method may differ.

DISPLAY

Changes the AUTO SHUTOFF setting.

MENU 2 AUTO SHUTOFF ON CHILD LOCK OFF BLUE BACK ON VIDEO-2 SET COMPONENT

⇔

SELECT BY EXIT BY OPERATE BY -+

DISPLAY

5 Press the DISPLAY button to turn

the display off.

•To operate a menu using the buttons on the front panel of the TV, refer to “Operating menus” on page 21.

2 Repeatedly press the MENU T

buttons to display a desired menu.

• If you hold down the y button, the next

menu is displayed.

• If the selected function is on the first line,

pressing the r button displays the preceding menu.

3 Repeatedly press the MENU T

buttons to select a desired function.

11

Using the TV’s menus

INPUT

You can view images from VCRs or other devices connected to your TV.

1 Press MENU T to display the

“MENU 1” menu, then select “INPUT”.

MENU 1 INPUT TV VNR ON COMPRESS(16:9) ON

CLOSED CAPTION PICTURE TILT 00

SELECT BY EXIT BY OPERATE BY -+

2 Press CHANNEL M or MENU

DISPLAY

/

to select the “VIDEO-1”, “VIDEO-2” or “VIDEO-3” mode.

TV mode changes to VIDEO mode. To return to TV mode, repeat step 1 and 2 and set to TV mode.

PICTURE TILT

< AV-29VT11/AV-29VT31 only>

There are cases where the Earth’s magnetic force may make the picture tilt. If this happens, you can correct the picture tilt.

1 Press MENU T to display the

“MENU 1” menu, then select “PICTURE TILT.

MENU 1 INPUT TV VNR ON COMPRESS(16:9) ON

CLOSED CAPTION PICTURE TILT 00

SELECT BY EXIT BY OPERATE BY -+

2 Continue pressing CHANNEL M

or MENU becomes level.

DISPLAY

/

until the picture

VNR

You can reduce picture noise.

1 Press MENU T to display the

“MENU 1” menu, then select “VNR”.

MENU 1 INPUT TV VNR ON COMPRESS(16:9) ON

CLOSED CAPTION PICTURE TILT 00

SELECT BY EXIT BY OPERATE BY -+

2 Press CHANNEL M or MENU

DISPLAY

/

to select “ON”.

To cancel the VNR function, select “OFF”.

COMPRESS (16:9)

This function converts a normal picture (4:3 aspect ratio) into a wide picture (16:9 aspect ratio). Use for pictures with a 16:9 aspect ratio that have been squeezed into a normal picture (4:3 aspect ratio), to restore their original dimensions.

1 Press MENU T to display the

“MENU 1” menu, then select “COMPRESS (16:9)”.

MENU 1 INPUT TV VNR ON COMPRESS(16:9) ON

CLOSED CAPTION PICTURE TILT 00

SELECT BY EXIT BY OPERATE BY -+

2 Press CHANNEL M or MENU

to select “ON”.

DISPLAY

/

12

To cancel the COMPRESS (16:9) function, select “OFF”.

Using the TV’s menus

CLOSED CAPTION

You can view closed captions or text information.

1 Press MENU T to display the

“MENU 1” menu, then select “CLOSED CAPTION”.

MENU 1 INPUT TV VNR ON COMPRESS(16:9) ON

CLOSED CAPTION PICTURE TILT 00

SELECT BY EXIT BY OPERATE BY -+

DISPLAY

2 Press CHANNEL M or MENU /.

The sub-menu is displayed.

CAPTION: TEXT :T1 T2 T3 T4

SELECT BY EXIT BY OPERATE BY -+

CC1 CC2 CC3 CC4

DISPLAY

3 Press MENU T to select

“CAPTION” or “TEXT”

4 Press CHANNEL M or MENU

.

/

to select the caption or text channel.

CHILD LOCK

You can disable the front control buttons of the TV. When this function is set to “ON”, the TV can be operated using only the remote control. Use this function to prevent children from operating the TV without parental consent.

1 Press MENU T to display the

“MENU 2” menu, then select “CHILD LOCK”.

MENU 2 AUTO SHUTOFF ON CHILD LOCK ON BLUE BACK ON VIDEO-2 SET COMPONENT

SELECT BY EXIT BY OPERATE BY -+

2 Press CHANNEL M or MENU

to select “ON”.

• To cancel the CHILD LOCK function, select

“OFF”.

• The CHILD LOCK function is canceled when you turn the power off.

DISPLAY

/

BLUE BACK

You can mute the sound and change the picture into a blue screen while no signals are received by the TV, or when the signals are unstable.

1 Press MENU T to display the

“MENU 2” menu, then select “BLUE BACK”.

MENU 2 AUTO SHUTOFF ON CHILD LOCK ON BLUE BACK ON VIDEO-2 SET COMPONENT

SELECT BY EXIT BY OPERATE BY -+

2 Press CHANNEL M or MENU

DISPLAY

/

to select “ON”.

To cancel the BLUE BACK function, select “OFF”.

• To view a broadcast even when the reception signal is poor, set the BLUE BACK function to “OFF”.

• Even when the BLUE BACK function is set to “OFF”, the sound may not be audible.

AUTO SHUTOFF

You can set your TV to turn off if no signals are received for about 15 minutes or longer after the end of a broadcast.

1 Press MENU T to display the

“MENU 2” menu, then select “AUTO SHUTOFF”.

MENU 2 AUTO SHUTOFF ON CHILD LOCK ON BLUE BACK ON VIDEO-2 SET COMPONENT

SELECT BY EXIT BY OPERATE BY -+

2 Press CHANNEL M or MENU

to select “ON”.

To cancel the AUTO SHUTOFF function, select “OFF”.

• The AUTO SHUTOFF function does not turn off the TV’s main power.

• The AUTO SHUTOFF will not work for a VIDEO mode.

DISPLAY

/

13

Using the TV’s menus

VIDEO-2 SET

Set the VIDEO-2 SET correctly according to the video signal input from the external device connected to the VIDEO-2 terminal. If this setting is incorrect, images will not be displayed.

1 Press MENU T to display the

“MENU 2” menu, then select “VIDEO-2 SET”.

MENU 2 AUTO SHUTOFF ON CHILD LOCK ON BLUE BACK ON VIDEO-2 SET COMPONENT

SELECT BY EXIT BY OPERATE BY -+

2 Set the VIDEO-2 SET according to

the video signal input from the VIDEO-2 terminal.

If a normal video signal (composite video signal) is input:

Press the CHANNEL m or the MENU

If a component video signal (Y/C signals) is input:

Press the CHANNEL m or the MENU

“COMPONENT”.

DISPLAY

buttons to select “VIDEO”.

/

buttons to select

/

B/CR

AUTO CH PRESET

You can automatically preset all TV channels that can be received by your TV to channels.

1 Press MENU T to display the

“MENU 3” menu, then select “AUTO CH PRESET”.

MENU 3 AUTO CH PRESET

CHANNEL SKIP SETUP TOUR LANGUAGE ENGLISH

MTS STEREO SAP MONO

ON AIR

SELECT BY EXIT BY OPERATE BY -+

2 Press CHANNEL M or MENU /.

The sub-menu is displayed.

TUNER MODE:CABLE AIR

START

SELECT BY EXIT BY OPERATE BY -+

3 Press CHANNEL M or MENU

to select “CABLE” or “AIR” .

4 Press MENU T to select “START”.

DISPLAY

/

14

5 Press CHANNEL M or MENU

to start the AUTO CH PRESET function.

“>>>ON SEARCH” is displayed on the screen.

When all the TV channels that can be received on your TV have been preset, the display goes out and the AUTO CH PRESET function operation is completed.

To stop the AUTO CH PRESET:

Press the CHANNEL m or the MENU

buttons.

/

Using the TV’s menus

CHANNEL SKIP

You can set undesired channels to be skipped. Channels set to be skipped cannot be selected by the CHANNEL m buttons or the CHANNEL SCAN button.

1 Press MENU T to display the

“MENU 3” menu, then select “CHANNEL SKIP”.

MENU 3 AUTO CH PRESET

CHANNEL SKIP SETUP TOUR LANGUAGE ENGLISH

MTS STEREO SAP MONO

ON AIR

SELECT BY EXIT BY OPERATE BY -+

2 Press CHANNEL M or MENU /.

The sub-menu is displayed.

SKIP NO EXIT CH 002 VL

SELECT BY CH -+ EXIT BY OPERATE BY VOL -+

3 Press CHANNEL M to select the

channel you want to skip.

4 Press VOLUME M to select “YES”.

The channel is set to be skipped. To cancel the CHANNEL SKIP function, select “NO”.

DISPLAY

SETUP TOUR

You can start the SETUP TOUR function.

1 Press MENU T to display the

“MENU 3” menu, then select “SETUP TOUR”.

MENU 3 AUTO CH PRESET

CHANNEL SKIP

SETUP TOUR

LANGUAGE ENGLISH MTS STEREO SAP MONO

ON AIR

SELECT BY EXIT BY OPERATE BY -+

DISPLAY

2 Press CHANNEL M or MENU /.

JVC logo appears and the SETUP TOUR function will start. For details, see page 6.

LANGUAGE

You can select the language for the on-screen display.

1 Press MENU T to display the

“MENU 3” menu, then select “LANGUAGE”.

MENU 3 AUTO CH PRESET

CHANNEL SKIP

SETUP TOUR

LANGUAGE ENGLISH MTS STEREO SAP MONO

ON AIR

SELECT BY EXIT BY OPERATE BY -+

DISPLAY

5 Repeat steps 3 and 4 if you want to

set another channel to skip.

To turn the display off:

1 Press MENU y to select “EXIT”.

SKIP NO EXIT CH 002 VL

SELECT BY CH -+ EXIT BY OPERATE BY VOL -+

DISPLAY

2 Press VOLUME m to turn the

display off.

2 Press CHANNEL M or MENU

to select language.

The on-screen display indications are in the selected language.

/

15

Using the TV’s menus

MTS

< Stereo model only>

You can select a MTS (Multi-Channel Television Sound) setting for stereo, mono and SAP (Second Audio Programs).

1 Press MENU T to display the

“MENU 3” menu, then select “MTS”.

MENU 3 AUTO CH PRESET

CHANNEL SKIP SETUP TOUR LANGUAGE ENGLISH MTS STEREO SAP MONO

ON AIR

SELECT BY EXIT BY OPERATE BY -+

2 Press CHANNEL M or MENU

DISPLAY

/

to select the mode.

• Select “MONO” to reduce excess noise in

a program or channel.

Picture Adjustments

You can adjust the picture as you like.

1 Press MENU T to display the

“MENU 4” menu.

MENU 4 TINT COLOR BRIGHT PICTURE DETAIL

SELECT BY EXIT BY OPERATE BY -+

2 Press MENU T to select an item

and press CHANNEL M or MENU

TINT* - : Reddish + : Greenish COLOR - : Lighter + : Deeper BRIGHT - : Darker + : Brighter PICTURE - : Lower + : Higher DETAIL - : Softer + : Sharper

* TINT (tint) is displayed only when

viewing images from NTSC 3.58 or NTSC

4.43 color systems.

DISPLAY

/

to adjust it.

Sound Adjustments

You can adjust the sound as you like.

1 Press MENU T to display the

“MENU 5” menu.

MENU 5 BASS TREBLE BALANCE AI VOLUME ON

SUPER BASS ON

SELECT BY EXIT BY OPERATE BY -+

DISPLAY

2 Press MENU T to select an item

and press CHANNEL M or MENU

TREBLE - : Weaker + : Stronger BASS - : Weaker + : Stronger BALANCE - : Left + : Right

/

to adjust it.

SUPER BASS

You can enjoy a powerful bass sound by using the SUPER BASS (Bass Reflex) function.

1 Press MENU T to display the

“MENU 5” menu, then select “SUPER BASS”.

MENU 5 BASS TREBLE BALANCE AI VOLUME ON SUPER BASS ON

SELECT BY EXIT BY OPERATE BY -+

2 Press CHANNEL –/+ or MENU

to select “ON”.

To cancel the SUPER BASS function, select “OFF”.

DISPLAY

/

16

Using the TV’s menus

AI VOLUME

You can prevent the sudden increase or decrease of volume that occurs when changing channels or switching VIDEO modes.

1 Press MENU T to display the

“MENU 5” menu, then select “AI VOLUME”.

MENU 5 BASS TREBLE BALANCE AI VOLUME ON

SUPER BASS ON

SELECT BY EXIT BY OPERATE BY -+

2 Press CHANNEL M or MENU

to select “ON”.

To cancel the AI VOLUME function, select “OFF”.

• The AI VOLUME function may not operate as expected if the sound input level from a broadcast station (or video software) is extremely low.

• The AI VOLUME function for TV mode and VIDEO mode can be set separately. For example, you can set it to be off in TV mode and on in VIDEO mode. If you set the AI VOLUME function while viewing a TV channel, the setting is registered as the setting for TV mode. If you set the AI VOLUME function while viewing images from a VIDEO terminal, the setting is registered as the setting for VIDEO mode.

DISPLAY

FAVORITE CH SETTING

You can set PICTURE MODE, VNR and PICTURE EFFECT functions for the favorite channels using FAVORITE CH SETTING menu.

1 Press MENU T to display the

“MENU 6” menu, then select “FAVORITE CH SETTING”.

MENU 6 FAVORITE CH SETTING VIDEO SETTING AI ECO SENSOR 1 AI ECO DISPLAY ON

SELECT BY EXIT BY OPERATE BY -+

DISPLAY

/

2 Press CHANNEL –/+ or MENU /.

The sub-menu is displayed.

FAVORITE CHANNEL : CH xxx PICTURE MODE : STANDARD VNR : ON PICTURE EFFECT : ON

SELECT BY EXIT BY OPERATE BY -+

DISPLAY

3 Press CHANNEL –/+ to select one of

the colours of “RED”, “GREEN”, “YELLOW” or “BLUE” assigned to FAVORITE CH button.

4 Press MENU T to select

“PICTURE MODE”, then press CHANNEL –/+ to select the picture mode of “BRIGHT”, “STANDARD” or “SOFT”.

5 Press MENU T to select “VNR”,

then press CHANNEL –/+ to select VNR “ON” or “OFF”.

6 Press MENU T to select

“PICTURE EFFECT”, then press CHANNEL –/+ to select PICTURE EFFECT “ON” or “OFF”.

• PICTURE MODE and VNR settings are

changed only when you press the FAVORITE CH button while PICTURE EFFECT is ON. Otherwise, PICTURE MODE and VNR are not changed.

17

Using the TV’s menus

VIDEO SETTING

You can set PICTURE MODE, VNR and PICTURE EFFECT functions for VIDEO mode using VIDEO SETTING menu.

1 Press MENU T to display the

“MENU 6” menu, then select “VIDEO SETTING”.

MENU 6 FAVORITE CH SETTING VIDEO SETTING AI ECO SENSOR 1 AI ECO DISPLAY ON

SELECT BY EXIT BY OPERATE BY -+

2 Press CHANNEL –/+ or MENU

The sub-menu is displayed.

VIDEO : VIDEO-1 PICTURE MODE : STANDARD VNR : ON PICTURE EFFECT : ON

RESET BY 0 SELECT BY EXIT BY OPERATE BY -+

3 Press CHANNEL –/+ to select

“VIDEO-1”, “VIDEO-2” or “VIDEO-3”.

4 Press MENU T to select

“PICTURE MODE”, then press CHANNEL –/+ to select the picture mode of “BRIGHT”, “STANDARD” or “SOFT”.

5 Press MENU T to select “VNR”,

then press CHANNEL –/+ to select VNR “ON” or “OFF”.

6 Press MENU T to select

“PICTURE EFFECT”, then press CHANNEL –/+ to select PICTURE EFFECT “ON” or “OFF”.

• PICTURE MODE and VNR settings are changed only when VIDEO input mode is selected while PICTURE EFFECT is ON. Otherwise, PICTURE MODE and VNR are not changed.

• Press 0 button to reset the setting.

DISPLAY

/

AI ECO SENSOR

You can enable this function so that the brightness of TV screen is automatically adjusted according to the brightness of your room.

1 Press MENU T to display the

“MENU 6” menu, then select “AI ECO SENSOR”.

MENU 6 FAVORITE CH SETTING VIDEO SETTING AI ECO SENSOR 1 AI ECO DISPLAY ON

SELECT BY EXIT BY OPERATE BY -+

DISPLAY

.

2 Press CHANNEL –/+ or MENU

/

to select “OFF”, “1” or “2”.

• For detailed description, see the “ECO SENSOR button” on page 9.

AI ECO DISPLAY

You can display on the screen the effect of the AI ECO SENSOR function.

1 Press MENU T to display the

“MENU 6” menu, then select “AI ECO DISPLAY”.

MENU 6 FAVORITE CH SETTING VIDEO SETTING AI ECO SENSOR 1 AI ECO DISPLAY ON

SELECT BY EXIT BY OPERATE BY -+

2 Press CHANNEL –/+ or MENU

to select “ON”.

The clover mark indicating the brightness of your room is displayed for several seconds each time the brightness changes. The number of clover marks displayed on screen increases as your room becomes darker. To cancel the AI ECO DISPLAY function, select “OFF”.

• To switch the AI ECO SENSOR’S mode, see the “ECO SENSOR button” on page 9.

DISPLAY

/

18

Attaching the Twin Port Bass Blaster Unit

<AV-21VT31/AV-25VT31/AV-29VT31 only>

The Twin Port Bass Blaster Unit is packaged together with the TV. Before you use the TV, mount the unit correctly on the TV.

Note:

• The SUPER BASS functions do not work unless the Twin Port Bass Blaster Unit is connected correctly to the TV. For details on the SUPER BASS functions, see page 8.

CAUTION:

• The Twin Port Bass Blaster Unit is just placed on top of the TV and is not held in place by a screw. When you use the unit, pay attention to the following cautions. Otherwise, the unit or TV may fall over and be damaged, or cause unexpected injury.

- Do not rest your hands or elbows on the unit.

- Do not move the TV with the Twin Port Bass Blaster Unit mounted on top of the TV. Before you

move the TV, be sure to remove the unit.

- Do not move the TV by holding the Twin Port Bass Blaster Unit.

1 Place the unit on top of the TV

making sure that the mounting pin on the bottom of the Twin Port Bass Blaster Unit fits into the mounting hole on the top of the TV.

• When you mount the unit, make sure that the mounting pin fits properly into the mounting hole. Otherwise, it may slide off the top of the TV. This may cause damage or cause unexpected injury.

2 Firmly insert the Twin Port Bass

Blaster Unit connector into the BASS SPEAKER OUT terminal.

Twin Port Bass Blaster Unit

COMPONENT

VIDEO-1

(

)

VIDEO-2

INPUT

S

OVER

V

Y

/

L

/

MONO

RRRC

V

L

C

B

/

MONO

R

BASS

SPEAKER

OUT

OUTPUT

V

L

19

TV buttons and parts

Front

<AV-29VT11/AV-29VT31>

2

1

3 64

<AV-21VT11/AV-21VT31/AV-25VT11/AV-25VT31>

5

4 531 2 7 8 9 0

8 7

9 0

<AV-21WA11>

Rear

R

V L /MONO

IN (

)

VIDEO-3

MENU

1 2

MENU

1 Headphone jack 2 VIDEO-3 terminal 3 MENU button 4 CHANNEL m buttons 5 VOLUME m buttons

COMPONENT

VIDEO-1

(

)

OUTPUT

VIDEO-2

INPUT

S

OVER

Y

V

L

/

MONO

RRRC

V

/

V

L

C

B

/

MONO

R

POWER

–

+

–

VOLUME

EXIT

+

CHANNEL

4 53 78 9 0

POWER

–

+

–

VOLUME

EXIT

+

CHANNEL

6 TV/VIDEO button 7 ECO sensor 8 Remote control sensor 9 POWER lamp 0 Main power button

1 VIDEO-1 INPUT terminal 2 COMPONENT (VIDEO-2)

INPUT terminal

3 OUTPUT terminal 4 Antenna socket

20

4321

Using the buttons on the TV

Basic operation

Check to make sure the CHILD LOCK function is set to “OFF”. When the CHILD LOCK function is set to “ON”, the TV cannot be operated using the front control buttons. For details, see “CHILD LOCK” on page 13.

1 Press CHANNEL M to turn the TV

on from standby mode.

2 Press CHANNEL M to select a

channel.

3 Press VOLUME M to adjust the

volume.

4 To turn your TV off, press the Main

power button to turn off the TV’s main power.

To change the TV mode to the VIDEO mode:

• Press the TV/VIDEO button if the TV has one. See page 7.

• If the TV has no TV/VIDEO button, select the VIDEO mode with the INPUT function in “MENU 1”.

Operating menus

You can operate functions in menus using the front control buttons on the TV.

1 Press MENU y to display a menu.

2 Press MENU y repeatedly to display

the menu you want to use.

3 Press MENU y to select the desired

function or item.

4 Press CHANNEL –/+ or VOLUME M

to carry out the desired operation.

For details, see the description for each function.

5 Press VOLUME M to turn the menu

display off.

21

Troubleshooting

If there is no picture or the TV does not operate normally, make sure the problem isn’t due to the reasons indicated below.

If the problem persists even after taking the measures indicated, please contact a service technician.

Cannot turn the TV on

• Press the Main power button on the TV.

• Connect the power cord to the AC outlet.

The screen turns blue

• Is the BLUE BACK function on? (see page 13.)

Remote control inoperable

• Replace the batteries. (see page 3.)

Buttons on front of the TV do not work

• Switch the CHILD LOCK function off. (see page 13.)

TV does not respond immediately

• Press the main power button on the TV to turn off the main power. Press the main power button again to turn on the TV. If the TV returns to a normal state, operation is normal.

The TV turns off suddenly

• Is the OFF TIMER function set to operate? (see page 9.)

• Is the AUTO SHUTOFF function on? (see page 13.)

Poor sound

• Adjust the sound settings. (see page 16.)

Poor picture

• Press the COLOR SYSTEM button to select another color system. (see page 8.). However, color system cannot be changed in TV mode.

• Adjust the picture settings. (see page 16.)

• Is a component signal output device, such as a DVD player, connected correctly? (see page 5.)

• Is the “VIDEO-2 SET” function setting correct? (see page 14.)

• If noise (snow) totally blocks out the picture, check the following.

- Have the TV and antenna been connected

properly?

- Has the antenna cable been damaged?

- Is the antenna pointing in the right direction?

- Is the antenna itself faulty?

• If the TV or antenna suffer interference from other equipment, stripes or noise may appear in the picture. Move any equipment which can cause interference away from the TV.

• If the TV or antenna suffer interference from signals reflecting from mountains or buildings, double-pictures (ghosting) will occur. Change the antenna’s direction or replace it with an antenna with better directionality.

• When a white and bright still image (such as a white dress) is displayed on the screen, the white part may look as if it is colored. When the image disappears from the screen, the unnatural colors will also disappear.

22

The picture is tilted

< AV-29VT11/AV-29VT31 only>

• A picture may be tilted due to the influence of the earth’s magnetism. In this case, use the PICTURE TILT function to adjust the tilt. (see page 12.)

Screen is 80% black

• Press the CLOSED CAPTION button to select “OFF”. (see page 9.)

Specifications

TV RF systems

M

Color systems

NTSC 3.58 (in TV mode only) NTSC 3.58, NTSC 4.43, PAL (in VIDEO mode only)

Channels

VHF low channel (VL), VHF high channel (VH), UHF channel (U) Receives cable channels in mid band, super band and hyper band.

External input / output

VIDEO-1: S-video input, VIDEO input, AUDIO L/R input VIDEO-2/COMPONENT: VIDEO input, AUDIO L/R input,

VIDEO-3: VIDEO input, AUDIO L/R input OUTPUT: VIDEO output , AUDIO L/R output Headphone jack: stereo mini jack (3.5 mm diameter)

Sound-multiplex systems <Stereo models only>

MTS (Multi-Channel Television Sound)

Design and specifications subject to change without notice.

COMPONENT VIDEO (Y/C

B/CR) input

23

COLOR TELEVISION

INSTRUCTIONS

Thank you for buying this JVC color television. To make sure you understand how to use your new TV, please read this manual thoroughly before you begin.

AV-21VT11 AV-29VT11

Safety precautions

WARNING

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION

TO ENSURE PERSONAL SAFETY, OBSERVE THE FOLLOWING RULES REGARDING THE USE OF THIS TV.

• Operate only from the power source specified on the TV.

• Avoid damaging the power cord and main plug. When you unplug the TV, pull it out by the main plug. Do not pull on the power cord.

• Never block or cover the cabinet opening for ventilation. Never install the TV where good ventilation is unattainable. When installing this TV, leave spaces for ventilation around the TV more than the minimum distances shown in the diagram.

• Do not allow objects or liquid into the cabinet openings.

• In the event of a fault, unplug the TV and bring to JVC service centre. Do not attempt to repair it by yourself or remove the rear cover.

• The surface of the TV screen is easily damaged. Be very careful with it when handling the TV. Should the TV screen become soiled, wipe it with a soft dry cloth. Never rub it forcefully. Never use any cleaner or detergent on it.

• When you don’t use this TV for a long period of time, be sure to disconnect the power plug from the AC outlet.

• The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

10 cm

15 cm

15 cm10 cm

Preparation

1 Insert the batteries into the remote

control

Correctly insert two batteries, observing the , and polarities and inserting the . end first.

CAUTION:

Follow the cautions printed on the batteries.

Notes:

• Use AA/R6/UM-3 dry cell batteries.

• If the remote control does not work properly, fit new batteries. The supplied batteries are for testing, not regular use.

2

.

Preparation

2 Connecting the aerial and VCR

• Read the manuals provided with the devices. Depending on the device, the connection method may be different from the diagrams. Also the device settings may need to change depending on the connection method.

• Turn off all the devices including the TV.

• Connecting cables are not supplied.

• When connecting monaural audio to the TV, use the L/MONO jack.

• You can connect an S-VIDEO compatible device (such as an S-VHS VCR) to the S-connector with an S-VIDEO cable and enjoy the high quality picture of the S-VIDEO signal (Y/C signal). In that case, do not connect it to the TV with a video cable.

Connecting the aerial

VIDEO-1

INPUT

S

OVER

V

L

/

MONO

RRRC

COMPONENT

(

VIDEO-2

INPUT

Y

/

V

C

B

L

R

/

MONO

)

OUTPUT

V

L

VHF/UHF outdoor aerial

Connecting the aerial and VCR

3

VCR

To audio output

To aerial input

To video output

To S-video output

To RF output

1

VIDEO-1

INPUT

S

OVER

V

L

/

MONO

RRRC

COMPONENT

(

VIDEO-2

INPUT

Y

/

V

C

B

L

/

R

MONO

)

VHF/UHF outdoor aerial

OUTPUT

V

L

2

3

Preparation

3 Connecting other devices

If you are not connecting any other devices, skip step 3 and perform step 4.

• Use the headphones with a stereo mini jack (3.5 mm in diameter). When you connect the headphones, the TV speakers go off.

• The OUTPUT terminal outputs the video and sound signals which you are viewing on the TV. You can dub them onto the VCR connected to the OUTPUT terminal. (The OUTPUT terminal cannot output S-VIDEO signals or component video signals. Also it cannot output any signals when the TV is turned off.)

• Connect components outputting a component signal (Y/C to the VIDEO-2 terminal, and set VIDEO-2 SET function to “COMPONENT”. (See page 13.)

• The following illustrations are for the AV-21VT11. Your TV’s front and rear panels may not look exactly like the illustrations.

Front

Headphones

Rear

COMPONENT

VIDEO-1

(

)

OUTPUT

VIDEO-2

INPUT

S

OVER

B/CR signal), such as a DVD player,

Camcorder or TV game

VCR (for playing) DVD player

(composite signals)

V

Y

/

V

L

C

B

/

MONO

RRR

R

L

/

MONO

V

L

VCR (for recording)

RC

DVD player

(component video signals)

4 Connect the power cord to the AC outlet

Operate only from the power source indicated on the rear of the TV.

4

Preparation

5 SETUP TOUR

When the TV is first turned on, it enters the SETUP TOUR mode, and the JVC logo is displayed. Follow the instructions on the on-screen display to perform the SETUP TOUR.

• In case of resetting that the reason for such as removal, you can set the AUTO CH PRESET function on the “MENU 3” menu. For details, see page 13.

1 Press the Main power button

on the TV.

The POWER lamp lights. After the JVC logo has been displayed, the TV automatically switches to the language setting mode.

SETUP TOUR

2 Press the MENU y button.

SETUP TOUR

LANGUAGE

ENGLISH

EXIT BY

DISPLAY

3 Press the CHANNEL –/+ or

/

the MENU

buttons to select the tuner mode (AIR or CABLE).

SETUP TOUR

TUNER MODE

AIR

EXIT BY

DISPLAY

4 The AUTO PROGRAMMING

function will start and the indicator blinks.

SETUP TOUR

NOW PROGRAMMING

STOP BY

-+

DISPLAY

button

MENU

buttons

CHANNEL –/+

buttons

• To stop the AUTO PROGRAMMING function, press the CHANNEL m or the MENU

When all the TV channels that can be received on your TV have been preset, the display goes out and the AUTO PROGRAMMING function operation is completed.

5 Upon the completion of AUTO

PROGRAMMING function, the message below is displayed.

SETUP TOUR

THANK YOU!

SET IS NOW COMPLETE

POWER lamp

COLOR SYSTEM

DISPLAY

/

CLOSED CAPTION

TV/VIDEO

PICTURE

CHANNEL

SCAN

buttons.

/

POWER

123

OFF

TIMER

456

MODE

789

RETURN+ 100+

CHANNEL

Main power button

CINEMA

SURROUND

ECO

SENSOR

MENU

0

VOLUME

MENU t

buttons

5

Basic Operation

<RM-C1331>

MUTING

COLOR

SYSTEM

DISPLAY

CLOSED CAPTION

TV/VIDEO

123

OFF

TIMER

456

PICTURE

MODE

789

CHANNEL

RETURN

SCAN

CHANNEL

CINEMA

SURROUND

MENU

+

FAVORITE CH

RM-C1331

TV

0

VOLUME

POWER

ECO

SENSOR

+

100

1 Press the POWER button to

turn your TV on.

• If your TV does not turn on, press the Main power button on the TV then press the POWER button again.

• You can also turn on your TV by pressing any of the following buttons;

- the CHANNEL m button

- the Number buttons

- the TV/VIDEO button

2 Select a channel.

■ Press the CHANNEL m button.

• Up/down selection cannot be selected for channels to which the CHANNEL SKIP has been set to “YES”. See page 14.

■ Press the Number buttons to enter the channel number.

• When you want to select a

channel number over 100, enter the two-digit number after pressing the 100+ button.

3 Press the VOLUME M

button to adjust the sound.

4 To turn your TV off, press

the POWER button.

• We recommend that you press the

Main power button on the TV to turn the main power off if you do not plan to use your TV for a long time or if you wish to save energy.

If the picture is not clear:

Press the COLOR SYSTEM button to select another color system, see page 7.

Viewing Images from an External Device:

Press the TV/VIDEO button to select the VIDEO mode.

• You can also use the INPUT function to select the VIDEO mode. For details, refer to page 11.

6

Remote control buttons and functions

MUTING button

You can turn the sound off instantly.

Press this button.

To turn the sound on, press this button again.

COLOR SYSTEM button

If the picture is not clear or no color appears, change the current color system to another color system.

Press this button to select the color system.

In TV mode:

NTSC 3.58 (Fixed)

In Video mode:

AUTO

PAL

NTSC3.58

NTSC4.43

AUTO:

Automatic color system selection.

• If the picture is not normal in the AUTO mode, change the AUTO mode to another color system.

DISPLAY button

You can continuously display the current channel number or VIDEO mode on the screen.

Press this button.

To turn the display off, press this button again.

• When selecting a VIDEO mode with no signal, indication of the VIDEO mode becomes fixed on the screen.

CINEMA SURROUND button

You can enjoy an enhanced sound for a wider audience by using CINEMA SURROUND function.

Press this button to select one of the CINEMA SURROUND mode.

HIGH/LOW:

When you listen to the stereo sound, please select HIGH mode or LOW mode. You can enjoy the sound for a wider audience similar to the experience at the theatre.

• In case that you setting up the CINEMA SURROUND function to HIGH mode, there may be slight volume distortion. In case that occurs, please switch the HIGH mode to LOW mode, the effect of CINEMA SURROUND functions will be less noticeable, however, the volume distortion will be corrected.

MONO SURROUND:

Select the MONO SURROUND mode, when you listen to the mono sound. You can enjoy the sound for a wider audience similar to stereo sound.

OFF:

The CINEMA SURROUND function switches off.

7

Remote control buttons and functions

ECO SENSOR button

You can adjust this TV so that the screen automatically adjusts to the optimum contrast according to the brightness of your room. This function reduces eye strain and the power consumption of this TV.

Press this button to select the desired mode.

AI ECO SENSOR 1:

The AI ECO SENSOR function switches on.

Usually, it is recommended to watch the TV in this mode.

AI ECO SENSOR 2:

The AI ECO SENSOR function switches on.

If you feel the screen in the “AI ECO SENSOR 1” mode is too dark, select this mode.

AI ECO SENSOR OFF:

The AI ECO SENSOR function switches off.

• You can display on the screen the effect of the AI ECO SENSOR function. For details, see “AI ECO DISPLAY” on page 17.

OFF TIMER button

You can set the TV to automatically turn off after a set time.

Press this button to select the period of time.

• You can set the period of time to a maximum of 120 minutes in 10 miniute increments.

• 1 minute before the OFF TIMER function turns off the TV, “GOOD NIGHT!” appears.

To display the remaining time, press this button once.

To cancel the OFF TIMER function, press this button to set the period of time to “0”.

• The OFF TIMER function will not turn off the TV’s main power.

CLOSED CAPTION button

If they are included in a program, you can view closed captions or text information.

Press this button to select the mode.

CLOSED CAPTION

OFF

• To change caption or text channels see page 11.

TEXT

CHANNEL SCAN button

You can quickly view all TV channels programmes that you can view on your TV, and search for the programme you want to view.

1 Press this button to start scanning

TV channels.

The TV channel programmes are each displayed for several seconds.

• The programmes of TV channels for

which the SKIP function is set to “YES” are not displayed.

2 When you find the programme you

want to view, press this button again to stop scanning.

8

PICTURE MODE button

You can select one of three picture adjustment settings as you like.

Press this button to select a mode.

BRIGHT:

Heightens contrast and sharpness.

STANDARD:

Standardizes picture adjustments.

SOFT:

Softens contrast and sharpness.

• Pressing this button returns all the picture settings in “MENU 4” to their default settings.

Remote control buttons and functions

FAVORITE CH button

When tuner mode is AIR, you can correlate 4 channels out of 68 channels (CH02-CH69) with FAVORITE CH buttons RED, GREEN, YELLOW and BLUE.

When tuner mode is CABLE, you can correlate 4 channels out of 125 channels (CH01-CH125) with FAVORITE CH buttons RED, GREEN, YELLOW and BLUE.

Press one of the FAVORITE CH buttons for more than 3 seconds to correlate currently watching channel. After the channel and button are correlated, you can directly select favorite channel by the correlated button.

• When MENU is displayed, FAVORITE CH cannot be correlated.

• Correlation of FAVORITE CH button and the channel cannot be reset eventhough the main power is turned off.

• After tuner mode is changed by AUTO CH PRESET, FAVORITE CHANNELS are reset to default setting.

Default setting:

RED .............. CH02

GREEN .......... CH03

YELLOW ....... CH04

BLUE ............ CH05

Please refer to AUTO CH PRESET on page 13.

RETURN + button

You can set a channel you frequently view to the Return Channel and you can view that channel at any time with one-touch.

To set the channel to the Return Channel:

1 Select the channel you want to set

to the Return Channel.

2 Press this button and hold until the

message “RETURN PLUS PROGRAMMED!” appears.

• When you turn off the TV, the Return Channel setting is canceled.

To view the Return Channel:

Press this button.

• You can view two channels (current channel and Return Channel) alternately by pressing this button.

To cancel the Return Channel setting:

Press this button and hold until the message “RETURN PLUS CANCELED!” appears.

If no channel is set to the Return Channel:

You can view the channel selected right before the current channel by pressing this button.

9

Using the TV’s menus

This TV has a number of functions you can operate using the menus. To use all your TV’s functions fully, you need to understand how to use the menus.

COLOR

123

OFF

TIMER

456

MODE

789

RETURN+ 100+

CHANNEL

SURROUND

MENU

CINEMA

0

VOLUME

ECO

SENSOR

MENU t

buttons

DISPLAY

button

MENU

buttons

CHANNEL –/+ buttons

SYSTEM

DISPLAY

/

CLOSED CAPTION

TV/VIDEO

PICTURE

CHANNEL

SCAN

■ Basic operation

1 Press the MENU T buttons.

One of the 6 menus is displayed.

MENU number

The icon

on the left indicates the currently selected function.

MENU 1 INPUT TV VNR ON COMPRESS(16:9) ON CLOSED CAPTION

PICTURE TILT 00

SELECT BY EXIT BY OPERATE BY -+

DISPLAY

3 Repeatedly press the

MENU T buttons to select a desired function.

4 Press the CHANNEL –/+ or the

/

MENU

buttons to change

function settings.

Example:

MENU 2 AUTO SHUTOFF OFF CHILD LOCK OFF BLUE BACK ON VIDEO-2 SET COMPONENT

SELECT BY EXIT BY OPERATE BY -+

• With some functions, the operation method may differ.

DISPLAY

Changes the AUTO SHUTOFF setting

MENU 2 AUTO SHUTOFF ON CHILD LOCK OFF BLUE BACK ON VIDEO-2 SET COMPONENT

⇔

SELECT BY EXIT BY OPERATE BY -+

DISPLAY

5 Press the DISPLAY button to

turn the display off.

• To operate a menu using the buttons on the front panel of the TV, refer to “Operating menus” on page 19.

2 Repeatedly press the

MENU T buttons to display a desired menu.

• If you hold down the y button, the next

menu is displayed.

• If the selected function is on the first

line, pressing the r button displays the preceding menu.

10

Using the TV’s menus

INPUT

You can view images from VCRs or other devices connected to your TV.

1 Press MENU T to display the

“MENU 1” menu, then select “INPUT”.

MENU 1 INPUT TV VNR ON COMPRESS(16:9) ON CLOSED CAPTION

PICTURE TILT 00

SELECT BY EXIT BY OPERATE BY -+

2 Press CHANNEL –/+ or MENU

DISPLAY

/

to select “VIDEO-1”, “VIDEO-2” or “VIDEO-3”.

TV mode changes to VIDEO mode.

CLOSED CAPTION

You can view closed captions or text information.

1 Press MENU T to display the

“MENU 1” menu, then select “CLOSED CAPTION”.

MENU 1 INPUT TV VNR ON COMPRESS(16:9) ON

CLOSED CAPTION

PICTURE TILT 00

SELECT BY EXIT BY OPERATE BY -+

2 Press CHANNEL M or MENU /.

The sub-menu is displayed.

CAPTION: TEXT :T1 T2 T3 T4

SELECT BY EXIT BY OPERATE BY -+

DISPLAY

CC1 CC2 CC3 CC4

DISPLAY

VNR

You can reduce picture noise.

1 Press MENU T to display the

“MENU 1” menu, then select “VNR”.

MENU 1 INPUT TV VNR ON COMPRESS(16:9) ON

CLOSED CAPTION

PICTURE TILT 00

SELECT BY EXIT BY OPERATE BY -+

2 Press CHANNEL –/+ or MENU

DISPLAY

/

to select “ON”.

To cancel the VNR function, select “OFF”.

COMPRESS (16:9)

This function converts a normal picture (4:3 aspect ratio) into a wide picture (16:9 aspect ratio).

Use for pictures with a 16:9 aspect ratio that have been squeezed into a normal picture (4:3 aspect ratio), to restore their original dimensions.

1 Press MENU T to display the

“MENU 1” menu, then select “COMPRESS (16:9)”.

MENU 1 INPUT TV VNR ON COMPRESS(16:9) ON

CLOSED CAPTION

PICTURE TILT 00

SELECT BY EXIT BY OPERATE BY -+

2 Press CHANNEL –/+ or MENU

to select “ON”.

DISPLAY

/

3 Press MENU T to select

“CAPTION” or “TEXT”.

4 Press CHANNEL M or MENU

to select the caption or text channel.

/

To cancel the COMPRESS (16:9) function, select “OFF”.

11

Using the TV’s menus

PICTURE TILT

<AV-29VT11 only>

There are cases where the Earth’s magnetic force may make the picture tilt.

If this happens, you can correct the picture tilt.

1 Press MENU T to display the

“MENU 1” menu, then select “PICTURE TILT”.

MENU 1 INPUT TV VNR ON COMPRESS(16:9) ON

CLOSED CAPTION PICTURE TILT 00

SELECT BY EXIT BY OPERATE BY -+

DISPLAY

2 Continue pressing CHANNEL –/+ or

MENU

/

until the picture

becomes level.

CHILD LOCK

You can disable the front control buttons of the TV.

When this function is set to “ON”, the TV can be operated using only the remote control.

Use this function to prevent children from operating the TV without parental consent.

1 Press MENU T to display the

“MENU 2” menu, then select “CHILD LOCK”.

MENU 2 AUTO SHUTOFF ON CHILD LOCK ON BLUE BACK ON VIDEO-2 SET COMPONENT

SELECT BY EXIT BY OPERATE BY -+

2 Press CHANNEL –/+ or MENU

to select “ON”.

To cancel the CHILD LOCK function, select “OFF”.

• The CHILD LOCK function is canceled when you turn the power off.

DISPLAY

/

AUTO SHUTOFF

You can set your TV to turn off if no signals are received for about 15 minutes or longer after the end of a broadcast.

1 Press MENU T to display the

“MENU 2” menu, then select “AUTO SHUTOFF”.

MENU 2 AUTO SHUTOFF ON CHILD LOCK ON BLUE BACK ON VIDEO-2 SET COMPONENT

SELECT BY EXIT BY OPERATE BY -+

2 Press CHANNEL –/+ or MENU

DISPLAY

/

to select “ON”.

To cancel the AUTO SHUTOFF function, select “OFF”.

• The AUTO SHUTOFF function does not turn off the TV’s main power.

• The AUTO SHUTOFF will not work for a VIDEO mode.

BLUE BACK

If no signal is being received or the signal is very weak, a blue screen automatically becomes the picture background.

If you wish to continue viewing the poor picture, you must set the BLUE BACK function to “OFF”.

1 Press MENU T to display the

“MENU 2” menu, then select “BLUE BACK”.

MENU 2 AUTO SHUTOFF ON CHILD LOCK ON BLUE BACK ON VIDEO-2 SET COMPONENT

SELECT BY EXIT BY OPERATE BY -+

2 Press CHANNEL –/+ or MENU

to select “ON”.

To cancel the BLUE BACK function, select “OFF”.

DISPLAY

/

12

Using the TV’s menus

VIDEO-2 SET

Set the VIDEO-2 SET correctly according to the video signal input from the external device connected to the VIDEO-2 terminal. If this setting is incorrect, images will not be displayed.

1 Press MENU T to display the

“MENU 2” menu, then select “VIDEO-2 SET”.

MENU 2 AUTO SHUTOFF ON CHILD LOCK ON BLUE BACK ON VIDEO-2 SET COMPONENT

SELECT BY EXIT BY OPERATE BY -+

2 Set the VIDEO-2 SET according to

the video signal input from the VIDEO-2 terminal.

If a normal video signal (composite video signal) is input:

Press the CHANNEL m or the MENU “VIDEO”.

If a component video signal (Y/C

B/CR signals) is input:

Press the CHANNEL m or the MENU “COMPONENT”.

DISPLAY

/

buttons to select

/

buttons to select

AUTO CH PRESET

You can automatically preset all TV channels that can be received by your TV to channels.

1 Press MENU T to display the

“MENU 3” menu, then select “AUTO CH PRESET”.

MENU 3 AUTO CH PRESET CHANNEL SKIP

SETUP TOUR LANGUAGE ENGLISH

MTS STEREO SAP MONO

ON AIR C SELECT BY EXIT BY OPERATE BY -+

2 Press CHANNEL M or MENU /.

The sub-menu is displayed.

TUNER MODE:CABLE AIR

START

SELECT BY EXIT BY OPERATE BY -+

3 Press CHANNEL M or MENU

to select “CABLE” or “AIR” .

4 Press MENU T to select

“START”.

5 Press CHANNEL M or MENU

to start the AUTO CH PRESET function.

“>>>ON SEARCH” is displayed on the screen.

When all the TV channels that can be received on your TV have been preset, the display goes out and the AUTO CH PRESET function operation is completed.

To stop the AUTO CH PRESET:

Press the CHANNEL m or the MENU

button.

/

DISPLAY

/

13

Using the TV’s menus

CHANNEL SKIP

You can set undesired channels to be skipped. Channels set to be skipped cannot be selected by the CHANNEL m buttons or the CHANNEL SCAN button.

1 Press MENU T to display the

“MENU 3” menu, then select “CHANNEL SKIP”.

MENU 3 AUTO CH PRESET CHANNEL SKIP

SETUP TOUR

LANGUAGE ENGLISH MTS STEREO SAP MONO

ON AIR C SELECT BY EXIT BY OPERATE BY -+

2 Press CHANNEL –/+ or MENU /.

The sub-menu is displayed.

SKIP NO EXIT CH 002 VL

SELECT BY CH -+ EXIT BY OPERATE BY VOL -+

3 Press CHANNEL M to select the

channel you want to skip.

4 Press VOLUME M to select “YES”.

The channel is set to be skipped. To cancel the CHANNEL SKIP function, select “NO”.

5 Repeat steps 3 and 4 if you want to

set another channel to skip.

To turn the display off:

1 Press MENU y to select “EXIT”.

SKIP NO EXIT CH 002 VL

SELECT BY CH -+ EXIT BY OPERATE BY VOL -+

DISPLAY

SETUP TOUR

You can start the SETUP TOUR function.

1 Press MENU T to display the

“MENU 3” menu, then select “SETUP TOUR”.

MENU 3 AUTO CH PRESET CHANNEL SKIP

SETUP TOUR

LANGUAGE ENGLISH

MTS STEREO SAP MONO

ON AIR C SELECT BY EXIT BY OPERATE BY -+

DISPLAY

2 Press CHANNEL M or MENU /.

JVC logo appears and the SETUP TOUR function will start. For details, see page 5.

MTS

You can select a MTS (Multi-Channel Television Sound) setting for stereo, mono and SAP (Second Audio Programs).

1 Press MENU T to display the

“MENU 3” menu, then select “MTS”.

MENU 3 AUTO CH PRESET CHANNEL SKIP

SETUP TOUR LANGUAGE ENGLISH MTS STEREO SAP MONO

ON AIR C SELECT BY EXIT BY OPERATE BY -+

2 Press CHANNEL –/+ or MENU

to select the mode.

• Select “MONO” to reduce excess noise in

a program or channel.

• This function is not available in VIDEO mode.

DISPLAY

/

2 Press VOLUME m to turn the

display off.

14

Using the TV’s menus

Picture Adjustments

You can adjust the picture as you like.

1 Press MENU T to display the

“MENU 4” menu.

MENU 4 TINT COLOR BRIGHT PICTURE DETAIL

SELECT BY EXIT BY OPERATE BY -+

DISPLAY

2 Press MENU T to select an item

and press CHANNEL –/+ or MENU

TINT* - : Reddish + : Greenish

COLOR - : Lighter + : Deeper

BRIGHT - : Darker + : Brighter

PICTURE - : Lower + : Higher

DETAIL - : Softer + : Sharper

* TINT (tint) is displayed only when

viewing images from NTSC3.58 or NTSC4.43 color systems.

to adjust it.

/

Sound Adjustments

You can adjust the sound as you like.

1 Press MENU T to display the

“MENU 5” menu.

MENU 5 BASS TREBLE BALANCE AI VOLUME ON

SELECT BY EXIT BY OPERATE BY -+

DISPLAY

AI VOLUME

You can prevent the sudden increase or decrease of volume that occurs when changing channels or switching VIDEO modes.

1 Press MENU T to display the

“MENU 5” menu, then select “AI VOLUME”.

MENU 5 BASS TREBLE BALANCE AI VOLUME ON

SELECT BY EXIT BY OPERATE BY -+

2 Press CHANNEL –/+ or MENU

to select “ON”.

To cancel the AI VOLUME function, select “OFF”.

• The AI VOLUME function may not operate as expected if the sound input level from a broadcast station (or video software) is extremely low.

• The AI VOLUME function for TV mode and VIDEO mode can be set separately. For example, you can set it to be off in TV mode and on in VIDEO mode. If you set the AI VOLUME function while viewing a TV channel, the setting is registered as the setting for TV mode. If you set the AI VOLUME function while viewing images from a VIDEO terminal, the setting is registered as the setting for VIDEO mode.

DISPLAY

/

2 Press MENU T to select an item

and press CHANNEL –/+ or MENU

BASS - : Weaker + : Stronger

TREBLE - : Weaker + : Stronger

BALANCE - : Left + : Right

/

to adjust it.

15

Using the TV’s menus

FAVORITE CH SETTING

You can set PICTURE MODE, VNR and PICTURE EFFECT functions for the favorite channels using FAVORITE CH SETTING menu.

1 Press MENU T to display the

“MENU 6” menu, then select “FAVORITE CH SETTING”.

MENU 6 FAVORITE CH SETTING VIDEO SETTING AI ECO SENSOR 1 AI ECO DISPLAY ON

SELECT BY EXIT BY OPERATE BY -+

2 Press CHANNEL –/+ or MENU /.

The sub-menu is displayed.

FAVORITE CHANNEL : CH xxx PICTURE MODE : STANDARD VNR : ON PICTURE EFFECT : ON

SELECT BY EXIT BY OPERATE BY -+

3 Press CHANNEL –/+ to select one

of the colors of “RED”, “GREEN”, “YELLOW” or “BLUE” assigned to FAVORITE CH button.

4 Press MENU T to select

“PICTURE MODE”, then press CHANNEL –/+ to select the picture mode of “BRIGHT”, “STANDARD” or “SOFT”.

5 Press MENU T to select “VNR”,

then press CHANNEL –/+ to select VNR “ON” or “OFF”.

6 Press MENU T to select

“PICTURE EFFECT”, then press CHANNEL –/+ to select PICTURE EFFECT “ON” or “OFF”.

• PICTURE MODE and VNR settings are

changed only when you press the FAVORITE CH button while PICTURE EFFECT is ON. Otherwise, PICTURE MODE and VNR are not changed.

DISPLAY

VIDEO SETTING

You can set PICTURE MODE, VNR and PICTURE EFFECT functions for VIDEO mode using VIDEO SETTING menu.

1 Press MENU T to display the

“MENU 6” menu, then select “VIDEO SETTING”.

MENU 6 FAVORITE CH SETTING VIDEO SETTING AI ECO SENSOR 1 AI ECO DISPLAY ON

SELECT BY EXIT BY OPERATE BY -+

2 Press CHANNEL –/+ or MENU /.

The sub-menu is displayed.

VIDEO : VIDEO-1 PICTURE MODE : STANDARD VNR : ON PICTURE EFFECT : ON

RESET BY 0 SELECT BY EXIT BY OPERATE BY -+

3 Press CHANNEL –/+ to select

“VIDEO-1”, “VIDEO-2” or “VIDEO-3”.

4 Press MENU T to select

“PICTURE MODE”, then press CHANNEL –/+ to select the picture mode of “BRIGHT”, “STANDARD” or “SOFT”.

5 Press MENU T to select “VNR”,

then press CHANNEL –/+ to select VNR “ON” or “OFF”.

6 Press MENU T to select

“PICTURE EFFECT”, then press CHANNEL –/+ to select PICTURE EFFECT “ON” or “OFF”.

• PICTURE MODE and VNR settings are changed only when VIDEO input mode is selected while PICTURE EFFECT is ON. Otherwise, PICTURE MODE and VNR are not changed.

• Press 0 button to reset the setting.

DISPLAY

16

Using the TV’s menus

AI ECO SENSOR

You can enable this function so that the brightness of TV screen is automatically adjusted according to the brightness of your room.

1 Press MENU T to display the

“MENU 6” menu, then select “AI ECO SENSOR”.

MENU 6 FAVORITE CH SETTING VIDEO SETTING AI ECO SENSOR 1 AI ECO DISPLAY ON

SELECT BY EXIT BY OPERATE BY -+

DISPLAY

2 Press CHANNEL –/+ or MENU

to select “OFF”, “1” or “2”.

• For detailed description, see the “ECO SENSOR button” on page 8.

AI ECO DISPLAY

You can display on the screen the effect of the AI ECO SENSOR function.

1 Press MENU T to display the

“MENU 6” menu, then select “AI ECO DISPLAY”.

MENU 6 FAVORITE CH SETTING VIDEO SETTING AI ECO SENSOR 1 AI ECO DISPLAY ON

SELECT BY EXIT BY OPERATE BY -+

2 Press CHANNEL –/+ or MENU

to select “ON”.

The clover mark indicating the brightness of your room is displayed for several seconds each time the brightness changes. The number of clover marks displayed on screen increases as your room becomes darker. To cancel the AI ECO DISPLAY function, select “OFF”.

DISPLAY

/

17

TV buttons and parts

<AV-29VT11>

2

1

<AV-21VT11>

3 645

4 531 27890

9087

18

1 Headphone jack 2 VIDEO-3 terminal 3 MENU button 4 CHANNEL m buttons 5 VOLUME m buttons

6 TV/VIDEO button 7 ECO sensor 8 Remote control sensor 9 POWER lamp 0 Main power button

Using the buttons on the TV

Basic operation

Check to make sure the CHILD LOCK function is set to “OFF”. When the CHILD LOCK function is set to “ON”, the TV cannot be operated using the front control buttons. For details, see “CHILD LOCK” on page 12.

1 Press CHANNEL –/+ to turn the TV

on from standby mode.

2 Press CHANNEL –/+ to select a

channel.

3 Press VOLUME –/+ to adjust the

volume.

4 To turn your TV off, press the Main

power button to turn off the TV’s main power.

To change the TV mode to the VIDEO mode:

• Press the TV/VIDEO button if the TV has one. See page 6.

• If the TV has no TV/VIDEO button, select the VIDEO mode with the INPUT function in “MENU 1”.

Operating menus

You can operate function in menus using the front control buttons on the TV.

1 Press MENU y to display a menu.

2 Press MENU y repeatedly to

display the menu you want to use.

3 Press MENU y to select the desired

function or item.

4 Press CHANNEL –/+ or

VOLUME –/+ to carry out the desired operation.

For details, see the description for each function.

5 Press VOLUME –/+ to turn the

menu display off.

19

Troubleshooting

If there is no picture or the TV does not operate normally, make sure the problem isn’t due to the reasons indicated below.

If the problem persists even after taking the measures indicated, please contact a service technician.

Cannot turn the TV on

• Press the Main power button on the TV.

• Connect the power cord to the AC outlet.

The screen turns blue

• Is the BLUE BACK function on? (see page 12.)

Remote control inoperable

• Replace the batteries. (see page 2.)

Buttons on front of the TV do not work

• Switch the CHILD LOCK function off. (see page 12.)

TV does not respond immediately

• Press the main power button on the TV to turn off the main power. Press the main power button again to turn on the TV. If the TV returns to a normal state, operation is normal.

The TV turns off suddenly

• Is the OFF TIMER function set to operate? (see page 8.)

• Is the AUTO SHUTOFF function on? (see page 12.)

Poor picture

• Press the COLOR SYSTEM button to select another color system. (see page 7.)

• Adjust the picture settings. (see page 15.)

• Is a component signal output device, such

as a DVD player, connected correctly? (see page 4.)

• Is the VIDEO-2 SET function setting correct? (see page 13.)

• If noise (snow) totally blocks out the picture, check the following.

- Have the TV and aerial been connected

properly?

- Has the aerial cable been damaged?

- Is the aerial pointing in the right direction?

- Is the aerial itself faulty?

• If the TV or aerial suffer interference from other equipment, stripes or noise may appear in the picture. Move any equipment which can cause interference away from the TV.

• If the TV or aerial suffer interference from signals reflecting from mountains or buildings, double-pictures (ghosting) will occur. Change the aerial’s direction or replace it with an aerial with better directionality.

• When a white and bright still image (such as a white dress) is displayed on the screen, the white part may look as if it is color red. When the image disappears from the screen, the unnatural color will also disappear.

Poor sound

• Adjust the sound settings. (see page 15.)

20

The picture is tilted

<AV-29VT11 only>

• A picture may be tilted due to the influence of the earth’s magnetism. In this case, use the PICTURE TILT function to adjust the tilt. (see page 12.)

Screen is 80% black

• Press the CLOSED CAPTION button to select “OFF”. (see page 11.)

Specifications

TV RF systems

M

Color systems

NTSC 3.58 (in TV mode only) NTSC 3.58, NTSC 4.43, PAL (in VIDEO mode only)

Receiving channels

VHF low channel (VL), VHF high channel (VH), UHF channel (U) Receives cable channels in mid band, super band and hyper band.

External input / output

VIDEO-1: S-VIDEO input, VIDEO input, AUDIO L/R input VIDEO-2/COMPONENT: VIDEO input, AUDIO L/R input,

COMPONENT VIDEO (Y/C VIDEO-3: VIDEO input, AUDIO L/R input OUTPUT: VIDEO output , AUDIO L/R output Headphone jack: stereo mini jack (3.5 mm diameter)

Sound-multiplex systems

MTS (Multi-Channel Television Sound)

Power consumption

AV-21VT11: 126W AV-29VT11: 190W

Screen size (Visible area)

AV-21VT11: 508mm AV-29VT11: 676mm

B/CR) input

Design and specifications subject to change without notice.

21

JVC AV-29VT11/P, AV-29VT11/T, AV-29VT31/P User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Contents

Safety precautions

Preparation

1 Confirm which remote control you have

2 Insert the batteries into the remote control

3 Connecting the antenna and VCR

4 Connecting other devices

5 Connect the power cord to the AC outlet

6 SETUP TOUR

Basic operation

Remote control buttons and functions

MUTING button

COLOR SYSTEM button

BASS button

CINEMA SURROUND button

DISPLAY button

ECO SENSOR button

CLOSED CAPTION button

OFF TIMER button

PICTURE MODE button

CHANNEL SCAN button

FAVORITE CH button

RETURN + button

Using the TV’s menus

■ Basic operation

INPUT

PICTURE TILT

COMPRESS (16:9)

CLOSED CAPTION

CHILD LOCK

BLUE BACK

AUTO SHUTOFF

VIDEO-2 SET

AUTO CH PRESET

CHANNEL SKIP

SETUP TOUR

LANGUAGE

Picture Adjustments

Sound Adjustments

SUPER BASS

AI VOLUME

FAVORITE CH SETTING

VIDEO SETTING

AI ECO SENSOR

AI ECO DISPLAY

Attaching the Twin Port Bass Blaster Unit

TV buttons and parts

Using the buttons on the TV

Troubleshooting

Specifications

Contents

Safety precautions

Preparation

2 Connecting the aerial and VCR

3 Connecting other devices

4 Connect the power cord to the AC outlet

5 SETUP TOUR

Basic Operation

Remote control buttons and functions

MUTING button

COLOR SYSTEM button

DISPLAY button

CINEMA SURROUND button

ECO SENSOR button

OFF TIMER button

CLOSED CAPTION button

CHANNEL SCAN button

PICTURE MODE button

FAVORITE CH button

RETURN + button

Using the TV’s menus

■ Basic operation

INPUT

CLOSED CAPTION

COMPRESS (16:9)

PICTURE TILT