1JVC AV-21SX1 EK
General Information
Also Covers
AV-21TS1 EK
Matrix
Item See Model Book
E2prom Replacement .............................................................................. AV-25TS1EK 5
Specifications
Item Content
Dimensions (W x H x D) ............................................................60.5cm x 47.6cm x 47.5cm
Mass ..................................................................................................... 23.7kg AV-21 SX1 EK
............................................................................................................ .21.3 Kg AV-21TS1 EK
TV RF System ............................................................................................................CCIR (I)
Colour System ..................................................................PAL / NTSC (only in EXT mode)
Stereo System....................................................................................................... NICAM 6.0
Teletext system.............FASTEXT (United Kingdom system) / WST (Standard System)
Receiving Channels and Freq.
UHF: E21 ~ E69 .........................................................................................470MHz - 862MHz
Intermediate Frequency
VIF Carrier ............................................................................................................... 39.5MHz
SIF Carrier ................................................................................................ 33.5MHz (6 0MHz)
Colour Sub Carrier Frequency
PAL ............................................................................................................................ 4.43MHz
NTSC ........................................................................................................ 3.58MHz / 4.43MHz
Aerial Input Terminal.................................................................. 75Ω Unbalanced, Coaxial
Power Input .......................................................................................... 220 - 240V AC, 50Hz
Power Consumption ............................................ 80W(Avg.) / 137W (Max.) AV-21SX1 EK
................................................................................74W (Avg.) / 114W (Max.) AV-21TS1 EK
Picture Tube ............................................ 21”( Visible size: 51cm), Diagonally measured
High Voltage........................................................... 26.5kV ± 1.5kV (at zero beam current)
Speaker........................................................ (10cm + 2cm) x 2, Round Type AV-21SX1 EK
.......................................................................... 5cm x 9cm x 2cm Oval Type AV-21TS1 EK
Audio Output........................................................................................................ 10W + 10W
EXT Input I Output...................... EXT-1 I EXT-2: 21-pin Euroconnector (SCART socket)
Audio Output....................................................Variable (0 ~ 1,000 Vrms) Low impedance
..........................................................................................................Centre .... RCA pin jack
............................................................................................. Front L, R .... RCA pin jack x 2
.............................................................................Surround L,R (Rear) .... RCA pin jack X2
Headphone Jack .......................................................................Stereo mini jack (ø 3.5mm)
Remote Control Unit .................... RM C770 [Battery size; AAA (R03) x 2] AV-21SX1 EK
.........................................................RM C760 [Battery size; AAA (R03) x 2] AV-21TS1 EK
can be different from the initial setting values.
Service Adjustments
BEFORE STARTING SERVICE ADJUSTMENT
1.There are 2 ways of adjusting this TV: One is
with the REMOTE CONTROL UNIT and the
other is the conventional method using
adjustment parts and components.
2.The setting (adjustment) using the REMOTE
CONTROL UNIT is made on the basis of the
initial setting values. The setting values which
adjust the screen to the optimum condition
3.Turn on the power of the TV and measuring
instrument for warming up for at least 30
minutes before starting adjustment.
4.Make sure that connection is correctly made to
AC power source.
5.If the receive or input signal is not specified,
use the most appropriate signal for adjustment.
6.Never touch parts (such as variable resistors,
transformers and condensers) not shown in
the adjustment items of this service adjustment.
7. Preparation for adjustment (presetting):
Unless otherwise specified in the adjustment
items, preset the following functions with the
REMOTE CONTROL UNIT:
MEASURING INSTRUMENT AND FIXTURES
1. DC voltmeter (or digital voltmeter)
2. Oscilloscope
3. Signal generator (Pattern genetator) [PAL /
NTSC]
4. Remote control unit
(1) SPATIAL EFFECT OFF
(2) BASS CENTRE
TREBLE CENTRE
BALANCE CENTRE
(3) CINEMA / GAME STANDARD
(4) ECO OFF
(5) 16:9(ASPECT SIZE) 4:3
ADJUSTMENT ITEMS
Adjustment item Adjustment item
B1 VOLTAGE check VSM PRESET setting
VIDEO/CHROMA circuit adjustment
FOCUS adjustment DEFLECTION circuit adjustment
IF circuit adjustment AUDIO circuit (Do not adlust.)
ADJUSTMENT LOCATIONS
BASIC OPERATION OF SERVICE MENU
1. TOOL OF SERVICE MENU OPERATION
Operate the SERVICE MENU with the
REMOTE CONTROL UNIT.
2. SERVICE MENU ITEMS
With the SERVICE MENU, various settings
(adjustment) can be made, and they are
broadly classified in the following items of
settings (adjustments):
1) 1. IF
For entering/adjusting the setting values
(adjustment values) of the IF circuit.
2) 2. V/C
For entering/adjusting the setting values
(adjustment values) of the VIDEO/CHROMA
circuit.
3) 3. AUDIO
For entering/adjusting the setting values
(adjustment values) of the multiplicity SOUND
circuit.
4) 4. DEF
For entering/adjusting the setting values
(adjustment values) of the DEFLECTION
circuit.
5) 5. VSM PRESET
For setting the values of STANDARD, USER,
CINEMA and GAME.
(VSM : video status memory)
3. BASIC OPERATION OF SERVICE MENU
1) How to enter SERVICE MENU
Press the DISPLAY key and the CINEMA/
GAME key of the REMOTE CONTROL UNIT
simultaneously. The SERVICE MENU screen
of Fig.1 will be displayed.
SERVICE MENU
1. IF 2. V/C
3. AUDIO 4. DEF
5. VSM PRESET
1-5: SELECT : EXIT
Fig. 1
2) Selection of SUB MENU SCREEN
1) Press one of the keys 1 ~ 5 of the REMOTE
CONTROL UNIT, and select the SUB MENU
SCREEN (See Fig. 2) from the SERVICE
MENU.
SERVICE MENU ➝ SUB MENU
1. IF
2. V/C
3. AUDIO
4. DEF.
5. VSM PRESET
3) Method of Setting
1) Method of Setting 1. IF
[1. VCO]
(1)1 Key.....Select 1.IF.
(2)1 Key.....Select 1.VCO.
(3)The VCO (OW) screen will be displayed in
yellow when the AFC voltage is at a certain
level and in blue when it is at other levels.
(4)DISPLAY Key. As you press this twice, you
will return to the SERVICE MENU.
[2. DELAY POINT]
(1)1 Key.....Select 1.IF.
(2)2 Key.....Select 2.DELAY POINT.
(3)FUNCTION -1+ Key Set (adjust) the setting
values of the setting items.
(4)VIDEO/SOUND Key..... Memorize the set
value. (Before storing the setting values in
memory, do not press the CH, TV /EXT,
DISPLAY, POWER ON/OFF keys - if you do,
the values will not be stored in memory.)
(5)DISPLAY Key.....When this is pressed twice,
you will return to the SERVICE MENU.
2) Method of setting 2.V/C, 3.AUDIO, 4.DEF
and 5.VSM PRESET
(1)2~5 Keys .....Select one from 2. V/C, 3.
AUDIO, 4. DEF and 5. VSM PRESET.
(2)FUNCTION UP/DOWN Key Select setting
items.
(3)FUNCTION - / + Key......Set (adjust) the
setting values of the setting items. (When 1
CUTOFF of 2.V/C is selected, press its -‘ or
“+“ function key, and the whole screen will
change to a faint horizontal line appearing in
its center. Press the same or +‘ key again,
and the screen will return to the original 1
CUTOFF screen.)
(4)VIDEO/SOUND KeyMemorize the setting
value. (Before storing the setting values in
memory, do not press the CH, TV / EXT,
DISPLAY, POWER ON / OFF keys - if you do,
the values will not be stored in memory.)
(5)DISPLAY Key ..... Return to the SERVICE
MENU screen.
4) Release of SERVICE MENU
1) After completings the setting, return to the
SERVICE MENU, then again press the DISPLAY key.
B1 VOLTAGE CHECK
Item Measuring Test point Adjustment part Description
Check of B1 Signal TP-91 (B1) 1. Receive a whole black signal.
Voltage generator TP-E
instrument
2. Connect a DC voltmeter to TP-91 and TP-E(4-).
DC Voltmeter X CONNECTOR 3 Make sure that the voltage is DC1 17 ± 2.0V.
(MAIN PWB)
FOCUS ADJUSTMENT
Item Measuring Test point Adjustment part Description
Adjustment Signal - FOCUS VR 1. Receive a cross-hatch signal.
of FOCUS generator - [In HVT] 2. While watching the screen, adjust the FOCUS VR to
instrument
make the vertical and horizontal lines as tine and sharp
as possible.
3. Make sure that when the screen is darkened, the lines
remain in good focus.
IF CIRCUIT ADJUSTMENT
Item Measuring Test point Adjustment part Description
Adjustment Remote T010 TRANSF. Do not make any adiustment unless the adjustment is
of VCO control unit out of way and you cannot get correct PICTURE.
Screen display Step
TOO HIGH Yellow ➝ Blue ➝ Blue
ABOVE REFERENCE Blue ➝ Yellow ➝ Blue
BELOW REFERENCE Blue ➝ Blue ➝ Yellow
TOO LOW Blue ➝ Blue
Adjustment Remote DELAY POINT 1. Receive a black and white signal (colour off).
of control unit (AGC TAKE-OVER) 2. Select 1.IF from the SERVICE MENU.
DELAY 3. Select 2.DELAY POINT by pressing the 2 key on the
POINT remote control.
(AGC) 4. Adjust the FUNCTION -/+ key until video noise
Setting Variable Initial setting
(adjustment) range value
item
DELAY POINT 0~63 4
(AGC TAKE-OVER)
instrument
VCO (CW)
TOO HIGH 2. Press 1 key and select 1 .VCO.
ABOVE REFERENCE 3. Select a receivable broadcast channel with the
BELOW REFERENCE <---------YELLOW CHANNEL key.
TOO LOW 4. Turn the core of T010 TRANSE. until the colour of the
MHZ <--------------fv 1. Select l.IF from the SERVICE MENU.
***.**
: EXIT from blue to yellow. (Step 1)
1 ➝ 2 ➝ 3
characters TOO HIGH displayed on the screen changes
5.Then slowly turn the core of T0l 0 TRANSE. to the left
until the colour of the characters BELOW REFERENCE
changes from blue to yellow. (Step 3)
6. Press the Display key three times to return to normal
screen.
7. Perform CHANNEL PRESET again, and make sure
that each broadcast is being received properly
disappears.
5. Press the VIDEO/SOUND key and memorize the set value.
6. Turn to other channels and make sure that there are
not irregularities.
VSM PRESET SETTING
Item Measuring Test point Adjustment part Description
Setting of Remote 1. BRIGHT 1. Select 5.VSM PRESET from the SERVICE MENU.
VSM control unit 2. CONT. 2. Select STANDARD with the CINEMA/GAME key.
PRESET 3. COLOUR 3. Adjust the FUNCTION UP/DOWN and FUNCTION -/+
instrument
4. SHARP key to bring the set values of 1. BRIGHT ~10 TREBLE to
5. TINT the values shown in the table.
6. R DRIVE 4. Press the VIDEO/SOUND key and memorize the set
7. G DRIVE value.
8. B DRIVE 5. Respectively select the VSM PRESET mode for USER,
9. BASS CINEMA and GAME, and make similar adjustment as in 3
10. TREBLE and 4 above.
Specifications / Service Adjustments / Adjustments Cont’d (1) / Adjustments Cont’d (2) / AV Selector PCB / Safety Parts
Front Control Diagram / CRT Diagram / Main Diagram 1 / Main Diagram 2
2JVC AV-21SX1 EK
Service Adjustments Cont’d
VSM preset mode STANDARD USER CINEMA GAME
Setting item
1. BRIGHT SETTING VALUE 0 0 +1 + 2
2. CONT. SETTING VALUE +10 +10 +3 + 2
3. COLOUR SETTING VALUE 0 0 -2 0
4. SHARP SETTING VALUE 0 0 -2 -2
5. TINT SETTING VALUE 0 0 0 0
6. R. DRIVE SETTING VALUE 0 0 0 0
7. G. DRIVE SETTING VALUE 0 0 -2 0
8. B. DRIVE SETTING VALUE 0 0 -5 0
9. BASS SETTING VALUE +4 (TS1) +4 (TS1) +8 (TS1) +6 (TS1)
0 (SX1) 0 (SX1) +6 (SX1) +4 (SX1)
10. TREBLE SETTING VALUE +4 (TS1) +4 (TS1) +6 (TS1) +2 (TS1)
0 (SX4) 0 (SX1) +2 (SX1) 0 (SX1)
SETTING VALUES OF VSM PRESET
VIDEO/CHROMA CIRCUIT ADJUSTMENT
The setting (adjustment) using the REMOTE CONTROL UNIT is made on the basis of the initial
setting values. The setting values which adjust the screen to the optimum condition can be different
from the initial setting values.
* Items in parentheses ( ) are automatically set to below table.
Setting Variable Initial
(adjustment) range setting
item value
1. CUTOFF ON / OFF OFF
2. R DRIVE -31~ +32 +12
3. G DRIVE -31~ +32 +2
4. B DRIVE -31~ +32 0
(Do not adjust) (Fixed)
5. BRIGHT -31~ +32 +6
6. CONT. -41~ +22 -10
Setting Colour system Variable PAL NTSC NTSC
(adjustment) range 3.58 4.43
item
7. COLOUR TV +3 - -
initial -31~ +32
setting
value Comp. VIDEO +3 +12 (+12)(SX1)
(0) (TS1)
8.TINT
initial Comp. VIDEO -31~ +32 - -2 (-2)(SX1)
setting (0) (TS1)
value
9.SHARP TV -31~ +32 0 0 (0)
(21TS 1 EK)
-8 ~ +7
Comp. VIDEO (21SX1 EK) 0 0 (0)
Item Measuring Adjustment part Description
instrument
Adjustment Remote 5. BRIGHT 1. Receive any broadcast.
of control unit 2. Select 2.V/C from the SERVICE MENU.
SUB BRIGHT 3. Select 5.BRIGHT with the FUNCTION UP/DOWN key.
4. Set the initial setting value with the FUNCTION -/+ key.
5. If the brightness is not the best with the initial set value, make fine
adjustment until you get the best brightness.
6. Press the VIDEO/SOUND key and memorize the set value.
Adjustment Remote 6. CONT. 1. Receive any broadcast.
of control unit 2. Select 2.V/C with the SERVICE MENU.
SUB CONT. 3. Select 6.CONT. with the FUNCTION UP/DOWN key.
4. Set the initial setting value with the FUNCTION -/+ key.
5. If the contrast is not the best with the initial set value, make fine
adjustment until you get the best contrast.
6. Press the VIDEO/SOUND key and memorize the set value.
Adlustment Remote 7. COLOUR [Method of adjustment without using measuring instrument]
of SUB control unit
COLOUR I PAL COLOUR (PAL COLOUR)
1. Receive a PAL broadcast.
2. Select 2.V/C from the SERVICE MENU.
3. Select 7.COLOUR with the FUNCTION UP/DOWN key.
4. Set the initial selling value for PAL COLOUR with the FUNCTION -/+ key.
5. If the colour is not the best with the initial set value, make fine
adjustment until you get the best colour.
6. Press the VIDEO/SOUND key and memorize the set value.
NTSC COLOUR (NTSC 3.58 COLOUR)
7. Input NTSC 3.58MHz COMPOSITE VIDEO signal from the EXT terminal.
8. Make similar fine adjustment of NTSC3.58 COLOUR as previously.
(NTSC 4.43 COLOUR)
When NTSC 3.58 is set, NTSC 4.43 will be automatically
set at the same value as NTSC 3.58.
Adjustment Signal TP-47B 7. COLOUR [Method of adjustment using measuring instrument]
of generator TP-E
SUB (CRT PAL COLOUR (PAL COLOUR)
COLOUR II Osciiioscope SOCKET 1. Receive a PAL full field colour bar signal (75% white).
PWB) 2. Select 2.V/C from SERVICE MENU.
Remote 3. Select 7.COLOUR with the FUNCTION UP/DOWN key.
control unit 4. Set the initial setting value of PAL COLOUR with the FUNCTION -/ + key.
5. Connect the oscilloscope to TP-47B.
6. Adjust PAL COLOUR and bring the value of (A) in the illustration to
- 4V (W~B).
7. Press the VIDEO/SOUND key and memorize the seting value.
NTSC COLOUR (NTSC 3.58 COLOUR)
1. Input NTSC 3.58MHz COMPOSITE VIDEO signal (full field colour bar 75%
white) from the EXT terminal.
2. Set the initial setting value of NTSC3.58 COLOUR with the FUNCTION
-/+ key.
3. Adjust NTSC3.58 COLOUR and bring the value of (A)of the illustration
to 0V (W~B).
4. Press the VIDEO/SOUND key and memorize the set value.
(NTSC 4.43 COLOUR)
When NTSC 3.58 is set, NTSC 4.43 will be automatically
set at the same value as NTSC 3.58.
Item Measuring Test point Adjustment Description
instrument part
Adjustment Signal TP-47B 8. TINT [Method of adjustment using measuring instrument]
of generator TP-E
SUB TINT II (CRT NTSC TINT (NTSC 3.58 TINT)
Oscilloscope SOCKET 1. Input COMPOSITE VIDEO signal (full field colour bar
PWB) 75% white) of NTSC3.S8MHz from the EXT terminal.
Remote 2. Select 2.V/C from the SERVICE MENU.
control unit 3. Select 8.TINT with the FUNCTION UP/DOWN key.
4. Set the initial setting value of NTSC 3.58 TINT with the
FUNCTION -/ + key.
5. Connect the oscilloscope to TP-47B.
6. Adjust NTSC3.58 TINT to bring the value of (A) of the
illustration to OV(W~Mg).
7. Press the VIDEO/SOUND key and memorize the setting value.
(NTSC 4.43 TINT)
When NTSC 3.58 is set, NTSC 4.43 will be automatically set at the
same value as NTSC 3.58.
Adjustment Remote 9. SHARP 1. Receive any broadcast.
of SHARP control unit 2. Select 2. V/C from the SERVICE MENU.
3. Select 9. SHARP with the FUNCTION UP DOWN key.
4. Set the initial setting value with the function -/ + key.
5. Press the VIDEO / SOUND key and memorize the
setting value.
DEFLECTION CIRCUIT ADJUSTMENT
There are 2 modes of adjustment - (1) 50Hz 4: 3 and (2) 60Hz 4:3 depending upon the kind of
signals (VERTICAL FREQUENCY 50Hz / 60Hz).
When adjusted in the (1) 50Hz 4:3 mode, the mode (2) will be linked to the mode (1) and will be
automatically adjusted for the same value.
When adjusted in the mode (2), only this mode will be adjusted singly.
Setting
(adlustment) Adjustment name Variable Initial setting value
item range 50Hz 60Hz
4:3 4:3
1. V-SLOPE Vertical hight -31~ + 32 -2 0
(Size of bottom side of screen)
2. V-SHIFT Vertical center -31~ + 32 +3 0
3. V-SIZE Vertical hight -31~ + 32 + 1 -1
4. H-CENT Horizontal center -31~ + 32 -5 + 10
-5 -1
8. V-S.CR Vertical hight correction -31~ +32
(Fixed) (Fixed)
Item Measuring Adjustment part Description
instrument
1. Signal 1. V-SLOPE [(1) 50Hz 4:3]
Adjustment generator 1. Receive a circle pattern signal of vertical frequency 50Hz. of
2. Select 4.DEF from the SERVICE MENU.
VERTICAL Remote 3. Select 1 V-SLOPE with the FUNCTION UP/DOWN key.
SLOPE control unit 4. Set the initial setting value of V-SLOPE (50Hz 4:3) with the FUNCTION -/+ key.
5. Adjust V-SLOPE and make the screen’s center line and the blanking line
coincide.
Item Measuring Adjustment part Description
instrument
Adjustment Signal R. CUT OFF VR 1. Receive a black and white signal (colour off).
of WHITE generator 2. Select 2.V/C trom the SERVICE MENU.
BALANCE G. CUT OFF VR 3. Select iCUT OFF with the FUNCTION UP/DOWN key.
(Low light) Remote 4. Show one horizontal line with the FUNCTION -/+ key. With
control unit B. CUT OFF VR the SCREEN VR, adjust so that the horizontal line will not be too bright.
SCREEN VR 5.Turn the CUT OFF VR respectively for R, 0 and B fully to the
[ In HVT] left (to the left direction when seen trom the rear).
6.Gradually turn the SCREEN VR from the left end to the right
direction to bring one of the red, green and blue colours faintly visible.
7. By adjusting the CUT OFF VR, bring out the other 2 colours and make
one horizontal line visible in white
8.Turn the SCREEN VR and bring one white horizontal line faintly visible.
9. With the -/ + key, turn off 1 CUTOFF screen.
Adjustment Signal 2. R. DRIVE 1. Receive a black and white signal (colour off).
of WHITE generator 3.G. DRIVE 2. Select 2.V/C with the SERVICE MENU.
BALANCE 3. Select 2.R DRIVE and 3.G DRIVE with the FUNCTION UP/DOWN key.
(High light) Remote 4.B. DRIVE 4. Change the screen colour to white with the FUNCTION -/+ key.
control unit (Do not adjust) 5. Press the VIDEO/SOUND key, and memorize the respectively set values
Specifications / Service Adjustments / Adjustments Cont’d (1) / Adjustments Cont’d (2) / AV Selector PCB / Safety Parts
Front Control Diagram / CRT Diagram / Main Diagram 1 / Main Diagram 2
Adjustment Remote 8. TINT [Method of adjustment without using measuring instrument]
of control unit
SUB TINT I NTSC TINT (NTSC 3.58 TINT)
1. Input COMPOSITE VIDEO signal of NTSC 3.58MHz from the EXT
terminal.
2. Select 2.V/C from the SERVICE MENU.
3. Select 8.TINT with the FUNCTION UP/DOWN key.
4. Set the initial setting value of NTSC 3.58 TINT with the
FUNCTION -/+ key.
5. If you cannot get the best tint with the initial setting value, make fine
adjustment until you get the best tint.
6. Press the VIDEO/SOUND key and memorize the set value.
(NTSC 4.43 TINT)
When NTSC 3.58 is set, NTSC 4.43 will be automatically
set at the same value as NTSC 3.58.
2. 2 V-SHIFT 6. Select 2.V-SHIFT and set the initial setting value.
Adjustment 7. Adjust V-SHIFT to make A =8.
of 8. Press the VIDEO/SOUND key and memorize the set value.
VERTICAL
SHIFT
3. 3. V-SIZE 9. Receive a cross-hatch signal.
Adjustment 10. Adjust 3.V-SIZE and set the initial setting value.
of 11. Adjust V-SIZE and make the vertical screen size 92% of the picture size.
VERTICAL 12. Press the VIDEO / SOUND key and memorize the set SIZE screen size
92V value.
Service Adjustments Cont’d
Item Measuring Adjustment part Description
instrument
4. 4. H-CENT 13.Receive a circle pattern signal.
Adjustment 14. Select 4.H-CENT and set the initial setting value.
of 15. Adjust H-CENT to make C=D.
HORI. 16.Press the VIDEO/SOUND key and memorize the set value.
CENTRE
8. 8. V-S. CR No alignment, but adjust this mode if result of no alignment is too bad.
Adjustment 17. Receive a cross-hatch signal.
of V-S. CR 18. Select 8.V-S. CR and set the initial setting values.
19. Adjust V-S. CR and make the gaps between the horizontal lines same.
20.Press the VIDEO/SOUND key and memorize the set values.
21. Make sure that the adjustment is properly done on the screen of (2) 60Hz 4:3.
3JVC AV-21SX1 EK
AUDIO CIRCUIT
Do not touch 3.AUDIO (1. CONC LIMIT, 2. A2 ID THR) of the SERVICE MENU as it requires no adjustment.
3. AUDIO
Setting (adjustment) item Variable Initial setting
range value (fixed)
1. CONG LIMIT (Do not adjust) 00H ~ FFH 0AH
2. A2 ID THR (Do not adjust) 00H ~ FFH 19H
Fig. 2 Service Menu Screen
CRT Diagram
Recommended Safety Parts
Item Part No. Description
1 A51EAL155X01 PICTURE TUBE(ITC) V01 (Inc.DY.&Wed)
2 CELD018-005J7 DEGAUSSING COIL L01
3 CM12774-A01-E REAR COVER
5 AEEMP003-185 POWER CORD
11 CM22875-007-E RATING LABEL (AV-21TS1 EK)
11 CM22875-008-E RATING LABEL (AV-21SX1 EK)
12 CE42545-001J1 H.V. TRANSF. T1551
100 CM12772-00B-E F.CABI ASSY (AV-21SX1 EK)
100 CM12772-A0C-E F.CABI ASSY (AV-21TS1 EK)
R1585 QRV141F-2201AY MF R 2.2k Ω 1/4W
R1586 QRV141F-1402AY MF R 14k Ω 1/4W
R1991 QRZ0057-825 C R 8.2M Ω 1W
C1522 QFZ0125-952N MPP CAP. 9500 p F 2000V ± 2.5%
C1524 QFZ0126-404N MPP CAP. 0.4µF 250V ± 2.5%
C1905 QCZ9034-472A C CAP. 4700 p FAC400V
C1906 QCZ9034-472A C CAP. 4700 P FAC400V
C1907 QCZ9034-472A C CAP. 4700 p FAC400V
C1992 QCZ9041-471A C CAP. 470 p FAC400V
C1993 QCZ9041-332A C CAP. 3300 p FAC400V
T1551 CE42545-001J1 H.V.TRANSF.
T1901 CET5043-002J4 SW REACTOR (AV-21TS1 EK)
T1901 CETS057-002J4 SW REACTOR (AV-21SX1 EK)
L1551 CELC901-064J6 HEATER CHOKE
D1901 D3SBA60 DIODE BRIDGE
Q1521 BU2506DX POWER TRANSISTOR H.OUT
Item Part No. Description
IC1902 TLP621(D4)-LF2 I.C.(PH.COUPLER)
CP1901 ICP-N38-Y I.C.PROTECT
CP1902 ICP-N75-Y I.C.PROTECT
CP1903 ICP-N75-Y I.C.PROTECT
FR1406 QRH127J-1R5M F R 1.5 Ω 1/2W
FR1552 QRH027K-R82M F R 0.82 Ω 2W
FR1553 QRH127J-6R8M F R 6.8 Ω 1/2W
FR1554 QRZ0054-4R7M F R 4.7 Ω 1/4W
FR1555 QRH027J-lR8M F R 1.8 Ω 2W
FR1556 QRH027J-2R2M F R 2 2 Ω 2W
FR1958 QRH017K-R56M F R (AV-21SX1 EK) 0.56 Ω 1W
FR1958 QRH027J-IR5M F R (AV-21TS1 EK)
FR1961 QRZ0054-331M F R 330 Ω 1/4W
SK3001 CE42535-001J1 C.R.T. SOCKET
C8901 QFZ9040-474N M F CAP. 0.47µ FAC275V
C8904 QFZ9040-473N MM CAP. 0.047µ FAC275V
F8901 QMF51D2-3R15J1 FUSE 3.15A
LF8901 AEELF002-001 LINE FILTER
S8901 QSP4K21-C01 PUSH SWITCH MAIN POWER
TH8901 CEKP010-001J2 W.P. THERMISTOR
CP0601 ICP-N10-Y I.C.PROTECT
R0403 QRZ0054-470M F R 47 Ω 1/4W
R0504 QRZ0054-330M F R 33 Ω 1/4W
R0509 QRZ0054-470M F R 47 Ω 1/4W
Recommended Safety Parts Cont’d
Specifications / Service Adjustments / Adjustments Cont’d (1) / Adjustments Cont’d (2) / AV Selector PCB / Safety Parts
Front Control Diagram / CRT Diagram / Main Diagram 1 / Main Diagram 2