COLOR TELEVISION EQUALIZER • CINEMA SURROUND • COMPONENT INPUT
Contents
AV-29BA16 AV-21BA16
AV-29MT16 AV-21MT16
AV-29ST16 AV-21VT16
AV-29VT16
AV-25MT16
Knowing your TV’s features .......................................................3
Remote control buttons and basic functions ..............................4
TV buttons and functions ............................................................6
Setting up your TV ......................................................................7
Basic setting for picture ..............................................................9
Advanced setting for picture ..................................................... 11
Basic setting for sound .............................................................12
Advanced setting for sound ......................................................13
DVD Menu ................................................................................15
Customized setting ...................................................................16
TV channel presetting ..............................................................18
Additional preparation ..............................................................19
Troubleshooting ........................................................................20
Specifi cations ...........................................................................21
INSTRUCTIONS
GGT0121-001A-H
Thank you for buying this JVC color television.
To make sure you understand how to use your new TV, please read this manual thoroughly before you begin.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE
CAUTION: TO ENSURE PERSONAL SAFETY, OBSERVE THE
1 Operate only from the power source indicated on the rear of the TV.
2 Avoid damaging the power cord and mains plug. When unplugging the
TV, grasp the mains plug. Do not pull on the power cord.
3 Never block or cover the ventilation openings.
Never install the TV where good ventilation is unattainable.
When installing this TV, leave spaces for ventilation around the TV of
more than the minimum distances as shown.
4 Do not allow objects or liquid into the cabinet openings.
5 In the event of a fault, unplug the unit and call a service technician.
Do not attempt to repair it yourself or remove the rear cover.
6 The surface of the TV screen is easily damaged. Be very careful with it
when handling the TV. Should the TV screen become soiled, wipe it with
a soft dry cloth. Never rub it forcefully. Never use any cleaner or detergent
on it.
THIS APPLIANCE TO RAIN OR MOISTURE.
FOLLOWING RULES REGARDING THE USE OF THIS TV.
15 cm
10 cm 10 cm
15 cm
7 This TV can be turned on/off power by connecting/disconnecting the AC
plug into AC outlet. While this TV is being installed, enough space should
be reserved for connection/disconnecting the AC plug into AC outlet by
hand.
8 The apparatus shall not be exposed to dripping or splashing and that
no objects fi lled with liquids, such as vases, shall be placed on the
apparatus.
WARNING: <AV-21M, AV-25M, AV-29M, AV-21B, AV-29B Series>
YOU CAN DETACH THE PROTECT SHEET ON THE TOP
THE FRONT BUTTON DOOR OF THE TV SHOULD BE
AND BOTTOM OF FRONT FRAME IF YOU NEEDED.
PULLED OUT FROM ITS BOTTOM. DO NOT PRESS THE
UPPER PART, OR YOUR FINGER MAY BE PINCHED.
PULL PULL
✓
2
Knowing your TV’s features
Main features
COLOR
CLOSED
CAPTION
VNR
ECO
RM-C1287
CINEMA
SURROUND
EXIT
100+
BASS
DVD MENU Just connect DVD player to the television. The television will detect DVD signal and display
picture on the screen automatically and you can adjust pictures and sound while you are
watching DVD as your desire. When disconnect DVD player, the television will display the
previous channel.
MaxxBass MaxxBass enhances bass sound that cannot be reproduced by normal speakers to be
heard by our ears.
MTS You can listen the stereo sound or SAP from TV program broadcating by MTS system.
(SAP: Second audio program.)
CLOSED CAPTION You can display dialog on the screen from TV broadcasting with Closed caption system.
You also may be able to display some information in text form if available.
FAVORITE CH (Channel) You can register up to four favorite channels for quick recall with one press.
AI ECO SENSOR TV detects the brightness of your room and automatically adjust the picture brightness to
a suitable level for a better eyecare.
ECO MODE You can adjust TV screen contrast according to the brightness of your room to suitable
level for a better eyecare.
AI VOLUME TV adjusts the volume automatically to the same level for all TV channels to avoid sudden
change of the volume when selecting different TV channels or selecting Video Mode.
VNR You can reduce the picture noise when viewing noisy TV programs or video sources.
TINT You can adjust TINT setting for all color systems, including PAL.
Confi rm your TV’s functions
Some functions written in this instruction manual may not be available for your TV.
Please see the chart below and check the functions that are equipped for your TV’s model number.
The model number is indicated at the rear of your TV. When you press a button concerned to a function that
is not available for your TV, it does not work and the logo “Ø” appears on the screen.
NO.
Function
1
MaxxBass
PICTURE TILT
—
MTS
—
2
AI ECO SENSOR
2
ECO MODE
Model No.
AV-29BA16
AV-29MT16
AV-29ST16
AV-29VT16
AV-25MT16
AV-21BA16
AV-21MT16
AV-21VT16
—OOOO—OO
OOOO————
—OOOO—OO
—OOOO—OO
O————O——
3
Remote control buttons and basic functions
CLOSED
CAPTION
No. Press To
POWER Turn on or off the TV from standby mode.
1
MENU/OK Display menu and confi rm selected function.
2
5 / ∞ / 2 / 3 Select and adjust menu function.
3
CHANNEL -/+ Select the desired channel number.
4
VOLUME -/+ Adjust the volume level.
5
TV/VIDEO
6
EXIT
MUTING Turn off the volume.
7
DISPLAY
8
/BACK
0~9, 100+ Select the program number. For three digits program number, press 100+, then press the number
9
RETURN+ a) Return to the frequently view channel with one touch.
!
CLOSED
"
CAPTION
FAVORITE
#
CHANNEL
(color buttons:
red, green,
yellow, blue)
Select TV or video terminal input.
On the other hand, you can use this button to EXIT from the menu.
Press this button again to resume the volume.
Display the program number or video terminal number on the screen.
On the other hand, you can use this button to return to the previous menu.
button.
1 Choose the channel you want to register.
2 Press and hold RETURN+ button until “RETURN PLUS PROGRAMMED!” appears.
To cancel, press and hold RETURN+ button until “RETURN PLUS CANCELED!” appears.
b) Return to the previously viewed channel, if you have not set or have cancelled the Return
channel as above.
Display information in text which are broadcasted by some TV channels.
Register and recall 4 favorite channels.
1. Choose the TV channel you want to register then press and hold a color button until
“PROGRAMMED! ■" appears.
2. To register other favorite channels, repeat step 1.
To recall the favorite channel, press the color button.
When the TV is in menu mode, the favorite channel function is not available.
COLOR
8
2
CLOSED
CAPTION
"
!
4
VNR
RM-C1287
1
#
6
EXIT
3
7
9
100+
5
4
Remote control buttons and basic functions (continued)
How to operate menus and menus locations
To Operation Note
Display the MENU
Choose a Top
menu
Choose a 2nd
menu
Display the 3rd
menu
Return to the
previous menu
Choose the setting
of a function
Adjust the effect
level of a function
Display the sub
menu of a function.
Press the MENU/OK button 2.
PICTURE MENU is displayed on
fi rst press.
Press 2/3 buttons 3 to choose
a menu title when the cursor is
pointing at MENU.
Press 5/∞ buttons 3 to choose a
2nd menu title.
Press 5/∞ buttons 3 to choose a
2nd menu title. Then press MENU/
OK button 2.
Press the DISPLAY/BACK button
8.
Press 5/∞ buttons 3 to choose
a function. Then press the 2/3
buttons 3 to change the setting.
Press 5/∞ buttons 3 to choose
a function. Then press the 2/3
buttons 3 to adjust the effect
level.
Press the 5/ ∞ buttons 3 to
choose a function. Then press
MENU/OK button 2 to display
the sub menu.
The following chart shows locations of functions in menus. In this manual,
location of a function is described as follows:
Top menu 2nd menuMENU
Top menu 2nd menu 3rd menuMENU
Note: Some functions have the 4th menus as the sub-menus.
To exit the MENU,
press the DISPLAY/
BACK button 8 or
choose EXIT menu
or TV/VIDEO/EXIT
button 6.
—
Press ∞ button 3
to display the next
functions.
—
Press the TV/ VIDEO/
EXIT button 6 to exit
from the menu.
—
Top menu 2nd menu Location 3nd menu Location
PICTURE PICTURE MODE P.9 – –
MENU
SOUND MTS P.13 – –
FEATURES DVD MENU P.15
INSTALL AUTO PROGRAM P.18 – –
PICTURE SETTING P.10 PICTURE P.10
WHITE BALANCE P.10 – –
VNR P.16 – –
AI VOLUME P.14 – –
SOUND MODE P.12 – –
EQUALIZER P.14 – –
BALANCE P.12 – –
CINEMA SURROUND
MaxxBass P.13 – –
ON TIMER P.16 CH P.16
OFF TIMER P.17 – –
CHILD LOCK P.16 – –
COMPRESS (16:9)
AI ECO SENSOR/
ECO MODE
CHANNEL SUMMARY
COLOR SYSTEM P.9 – –
VIDEO-2 SETTING P.17 – –
BLUE BACK P.11 – –
CLOSED CAPTION P.16 CAPTION P.16
PICTURE TILT P.11 – –
BEEP P.17 – –
P.13 – –
P.11 – –
P.11 – –
P.18 – –
BRIGHT P.10
DETAIL P.10
COLOR P.10
TINT P.10
AUTO SIGNAL DETECT
DVD PICTURE MODE
DVD THEATER STATUS
DVD SOUND MODE
ON TIMER P.16
TEXT P.16
P.15
P.15
P.15
P.15
5
TV buttons and functions
The illustrations shown below is for AV-21BA16 and AV-29ST16 only, which are used for explanation purpose.
Your TV may not look exactly the same as illustrated.
Front of the TV
AV-29ST16
POWER
TV/VIDEO
MENU/OK
CHANNEL
VOLUME
RVL/MONO
IN(VIDEO-3)
AV-21BA16
POWER
L / MONO
VR
IN (VIDEO-3)
MENU
OK
CHANNEL
VOLUME
Rear of the TV
AV-29ST16
#/-0/.%.4
6)$%/
6)$%/
/54054
).054
).054
3
/6%2
6
9
6
6
,22,
,
#
"
-/./
-/./
#
2
2
6
No. Button/terminal Description Page
L (main power)
1
POWER lamp Indicate the TV’s status. –
2
Press to turn on or turn off the TV’s main power. –
No color : TV’s main power is being turned off.
Red : TV’s main power is being turned on.
Blink :
While the TV is in turn on mode , OFF TIMER function is in used.
Note: When you turn off the power switch while TV is in standby mode,
While the TV is in standby mode, ON TIMER funciton is in used.
the power lamp will go off in 10 -15 seconds.
When you operate the TV, POWER Lamp will be blink.
ECO sensor –
3
Remote control sensor –
4
TV/VIDEO
5
VOLUME -/+ Press to adjust the volume level. –
6
CHANNEL -/+
7
MENU/OK Press to display the menu. –
8
IN (VIDEO-3) Video and audio input jacks for VIDEO-3 mode. 19
9
!
"
OUTPUT Video and audio output jacks. (The component video
#
COMPONENT
$
(VIDEO-2) INPUT
Press to select TV or Video terminal input or exit from menu.
Press to select the desired channel (Both of RF and Video input.)
Headphone jack. 19
Aerial socket. 7
signal cannot be output.)
Video or component video, and audio input jacks for VIDEO-2
mode. You can select the input signal by setting the “VIDEO-2
SETTING” function (see page 17).
VIDEO-1 INPUT
%
Video or S-VIDEO, and audio input jacks for VIDEO-1 mode. 7
How to operate the menus with the TV button
TV button
Work as same as the button on
the remote control unit
Note
MENU MENU/OK button To display main menu and exit menu after
fi nish setting.
CHANNEL -/+ ∞/5 button To select menu function.
VOLUME -/+ 2/3 button To choose a Top menu and adjust the
desired menu function.
–
–
19
19
Setting up your TV
CAUTION
• Turn off the equipment including the TV before connecting.
1 Connecting the aerial cable.
VHF/UHF outdoor aerial
Matching aerial
adapter (supplied)
)1
(
(
)2
2 Connecting the main plug to the AC outlet.
(
)3
75-ohm coaxial cable (not supplied)
If you connect a VCR, connect the aerial output jack of your VCR and
the aerial jack on the TV with aerial cable. Then connect the output
jacks of your VCR and the VIDEO-1 input jacks of the TV with the
video cable (or S-VIDEO cable if available) and audio cables. For
details, see the manual of your VCR.
Rear of TV
AV-29ST16
VCR
VHF/UHF outdoor aerial
COMPONENT
VIDEO-1
(VIDEO-2)
OUTPUT
INPUT
INPUT
S
OVER
V
Y
V
/
V
L
LRRL
B
C
/
/
MONO
MONO
C
R
R
The illustration shown is just a sample. It may not be same as your TV.
3 Inserting batteries into the remote control.
Insert two batteries by following the + and - polarities
and inserting the - end fi rst.
CAUTION:
Follow the cautions printed on the batteries.
Notes:
• Use AA/R6/UM-3 dry cell batteries.
• If the remote control does not work properly, fi t
new batteries. The supplied batteries are for testing,
not regular use.
4 Turn on the TV by pressing the main power button.
JVC logo appears on the screen.
JVC logo will appear on the screen again at the phase of “SETUP
TOUR RESTART?” function. Then the initial setting can be performed
according to page 8.
Note:
While in the INSTALL menu with the cursor pointing at INSTALL, pressing
the blue button will also display the JVC logo.
7
Setting up your TV (continued)
5 Making the initial settings
Set up your TV by pressing MENU/OK button or waiting for 15 seconds, then operate the TV by
following the steps below:
AUTO PROGRAM
AIR
CABLE
MENU : OK
DISPLAY : BACK
TV/VIDEO : EXIT
• Press 5/∞ button or
CH +/- key to select
AIR or CABLE, press
the MENU/OK button.
AUTO PROGRAM
10%
MENU : OK
• TV will start searching
for the channels.
To stop AUTO
PROGRAM, press
MENU/OK button.
CHANNEL SUMMARY
CH/CC SKIP
CH 02
■
CH 03
■
CH 04
■
CH 05
■
CH 06
CH 07
CH 08
MENU : OK
■
SKIP
■
CANCEL
• To complete the initial
setting, press the
MENU/OK button.
To set undesired
channels to be
skipped, see page 18.
When turn on the TV at
the next time
AUTO PROGRAM
SETUP TOUR RESTART?
■
: YES
MENU : NO
• “SETUP TOUR
RESTART?” will be
displayed.
Press the MENU/OK
button to cancel
the SETUP TOUR
RESTART function.
If you want to make
initial settings again
when the next time
you turn on the TV,
press the Red button
to activate the SETUP
TOUR RESTART
function.
8
Basic setting for picture
COLOR SYSTEM
You can select the appropriate color system when the picture is not
clear or no color appears.
Press the COLOR SYSTEM button to select a setting.
In TV mode: NTSC 3.58 MHz (Fixed).
In VIDEO mode:
AUTO PAL SECAM NTSC3.58
NTSC4.43
To operate this function with a menu:
MENU INSTALL menu COLOR SYSTEM
For the color system in each country or region, see the table below:
Area Country or Region System
Bahrain, Kuwait, Oman, Qatar, United Arab Emirates,
Yemen, etc.
Asia, Middle
East
Europe
Oceania Australia, New Zealand, etc. PAL
Africa
Indonesia, Malaysia, Singapore, Thailand, India, etc.
China, Vietnam, etc. PAL
Hong Kong, etc. PAL
Islamic Republic of Iran, Lebanon, Saudi Arabia, etc. SECAM
Philippines, Taiwan, Myanmar, etc. NTSC
Russia, etc. SECAM
Czech Republic, Poland, etc. PAL
Germany, Holland, Belgium, etc. PAL
UK, etc. PAL
Republic of South Africa, etc. PAL
Nigeria, etc. PAL
Egypt, Morocco, etc. SECAM
PAL
PICTURE MODE
You can choose the desired picture setting with one-touch.
Press the PICTURE MODE button to select a setting.
SOFT Softens contrast and sharpness.
BRIGHT Heightens contrast and sharpness.
STANDARD Standard picture setting.
USER You can change this picture setting as you like.
Select USER and adjust following items in the
PICTURE SETTING menu. (PICTURE, BRIGHT,
DETAIL, COLOR, TINT)
When you select VIDEO-2 Mode, you cannot adjust DETAIL.
When you set DVD THEATER STATUS in DVD MENU to ON, you
cannot adjust PICTURE MODE.
To operate this function with a menu:
MENU
PICTURE menu
PICTURE MODE
To return the USER setting to default, press the blue button when
the PICTURE SETTING menu is displayed.
About the basic operations of the menu, please see the “How to
operate menus and menus locations” on page 5.
9
Basic setting for picture (continued)
PICTURE SETTING
You can adjust the desired picture setting when selecting USER in
PICTURE MODE.
1 Select USER in PICTURE MODE under PICTURE menu.
MENU
USER
PICTURE menu PICTURE MODE
2 Select PICTURE SETTING in PICTURE menu, then adjust the
setting.
MENU
PICTURE 2 : Lower contrast 3 : Higher contrast
BRIGHT 2 : Darker 3 : Brighter
DETAIL 2 : Softer 3 : Higher
COLOR 2 : Lighter 3 : Deeper
TINT 2 : Reddish 3 : Greenish
PICTURE menu
When you select VIDEO-2 Mode, you cannot adjust DETAIL.
PICTURE SETTING
WHITE BALANCE
You can change the white balance of the picture to better match
the type of video being viewed.
Select WHITE BALANCE in the PICTURE menu, then choose the
desired setting.
MENU PICTURE menu WHITE BALANCE
NORMAL Normal white balance.
COOL Bluish white.
WARM Reddish white.
When you set DVD THEATER STATUS in DVD MENU to ON, you
cannot adjust WHITE BALANCE.
10
About the basic operations of the menu, please see the “How to
operate menus and menus locations” on page 5.
Advanced setting for picture
AI ECO SENSOR (ECO)/ECO MODE
You can adjust TV screen contrast according to the brightness of
your room.
Press the ECO button to select the desired mode.
OFF Cancel the function.
MODE-1/ECO-1 Mild contrast (recommended.)
MODE-2/ECO-2 Even contrast.
DISPLAY (for AI ECO SENSOR only)
Display the graphic of the function.
To operate this function with a menu:
MENU
FEATURES menu
AI ECO SENSOR / ECO MODE
When you set DVD THEATER STATUS in DVD MENU to ON, you
cannot adjust AI ECO SENSOR / ECO MODE.
Note : AI ECO SENSOR for M and S series.
ECO MODE for B series.
Correcting the Slanting Picture (PICTURE TILT)
You can correct the picture tilt caused by the earth’s magnetic force.
1 Select PICTURE TILT in the INSTALL menu, then press MENU/
OK button.
MENU INSTALL menu
The following display appears.
PICTURE TILT
PICTURE TILT
2 Press the 5/∞ buttons until the picture becomes level. Then
press the MENU/OK button.
COMPRESS (16:9)
You can convert a normal picture (4:3 aspect ratio) into a wide
picture (16:9 aspect ratio).
Select COMPRESS (16:9) in the FEATURES menu, then choose
ON or OFF.
MENU
BLUE BACK
You can set the TV to automatically change to a blue screen and
mute the sound if the signal is weak or absent, or when there is no
input from an antenna.
Select BLUE BACK in the INSTALL menu, then choose ON or OFF.
MENU INSTALL menu BLUE BACK
If you wish to continue viewing the poor picture, off the BLUE BACK
function.
FEATURES menu
COMPRESS (16:9)
MENU : OK
DISPLAY : BACK
TV/VIDEO : EXIT
About the basic operations of the menu, please see the “How to
operate menus and menus locations” on page 5.
11
Basic setting for sound
SOUND MODE
You can choose the desired sound setting.
Select the SOUND MODE in SOUND menu, then choose the setting.
MENU SOUND menu SOUND MODE
USER You can change this sound setting as you like.
SOUND TURBO
THEATER
MUSIC Emphasize on music effect.
NEWS Emphasize on vocal sound.
When you select VIDEO-2, you cannot adjust SOUND MODE
function. You can adjust it in DVD Menu.
When SOUND MODE is set to SOUND TURBO, EQUALIZER,
CINEMA SURROUND and MaxxBass functions are not available.
BALANCE
You can adjust the volume balance between the left and right
speakers.
Select BALANCE in SOUND menu, then adjust the setting.
MENU SOUND menu BALANCE
Select USER and adjust the frequencies in EQUALIZER
(100, 300, 1K, 3K, 8K Hz).
For details, see “EQUALIZER” on page 14.
Emphasize on low and high frequency levels.
Emphasize on movie sound.
12
About the basic operations of the menu, please see the “How to
operate menus and menus locations” on page 5.
Advanced setting for sound
CINEMA SURROUND
You can enjoy an enhanced sound for wider audience.
Press the CINEMA SURROUND button to select a setting.
OFF Cancel the function.
ON Listen to sound with wider audience effect.
This function is not available when SOUND MODE is set to SOUND
TURBO.
To operate this function with a menu:
MENU SOUND menu CINEMA SURROUND
MaxxBass
You can enjoy an enhanced bass sound which cannot be reproduced
by normal speakers.
Select MaxxBass in SOUND menu, then choose the desired setting.
MENU SOUND menu MaxxBass
OFF MaxxBass is turned off.
HIGH MaxxBass effect is high.
LOW MaxxBass effect is low.
This function is not available when SOUND MODE is set to SOUND
TURBO.
“MaxxBass” is a registered trademark of Waves Audio Ltd. in the
USA, Japan and other countries.
MTS
You can enjoy the stereo and SAP broadcasted programs.
Select the MTS in SOUND menu, then choose the desired mode.
MENU SOUND menu
STEREO Select stereo sound.
SAP Select second audio programs.
MONO Select monaural sound.
This function is not available in video mode.
MTS
About the basic operations of the menu, please see the “How to
operate menus and menus locations” on page 5.
13
Advanced setting for sound (continued)
EQUALIZER
You can adjust the sound level of each frequencies when selecting
USER mode in SOUND MODE.
1 Select USER in SOUND MODE under SOUND menu.
MENU
SOUND menu
SOUND MODE
USER
2 Select EQUALIZER in SOUND menu.
MENU
SOUND menu
EQUALIZER
The following display appears.
EQUALIZER
IIIIIII
IIIIIIII
IIIIIIIIIIIIIIII
IIIIIIIIIIIIIIII
100 300 1K 3K 8K Hz
MENU : OK
DISPLAY : BACK
TV/VIDEO : EXIT
3 Select and adjust the desired frequencies.
4 Press the MENU/OK button to exit the menu.
Adjust high frequency will affect higher pitch sound and vice versa.
When you select VIDEO-2, you cannot adjust EQUALIZER.
When you set DVD SOUND MODE in DVD MENU to USER,
you can adjust EQUALIZER under SOUND menu.
AI VOLUME
You can adjust the volume of all the channels and video inputs to
the same level automatically depends on the strength of signal of
the sources.
Select AI VOLUME in SOUND menu, then choose ON or OFF.
MENU SOUND menu AI VOLUME
14
About the basic operations of the menu, please see the “How to
operate menus and menus locations” on page 5.
DVD Menu
AUTO SIGNAL DETECT
When the DVD input signal is detected, the input mode will be changed
to VIDEO-2 automatically. And when the DVD input signal is not
detected, the input mode will be changed to RF previous input mode.
Select AUTO SIGNAL DETECT in DVD MENU under FEATURES
menu then choose ON or OFF (Factory setting is ON).
MENU
AUTO SIGNAL DETECT
FEATURES menu
DVD MENU
Press the “POWER ON” button on the DVD players or VCRs (follow
by the “PLAY” button for VCRs) so that the signal can be detected.
DVD PICTURE MODE
You can enhance the picture quality of the DVD or VIDEO-2.
Select DVD PICTURE MODE in DVD MENU under FEATURES
menu, then choose the desired setting.
MENU FEATURES menu
DVD PICTURE MODE
OFF Cancel the function.
CLEAR-1
CLEAR-2
Select when the disc is with lots of noise (To soften the picture).
Select when the disc is with less noise (To sharpen the picture).
DVD MENU
DVD THEATER STATUS
You can enjoy an enhanced picture quality for movie playback in a
dark room, like watching a movie in the theater.
Select DVD THEATER STATUS in DVD MENU under FEATURES
menu, then choose ON or OFF.
MENU
FEATURES menu
DVD THEATER STATUS
DVD MENU
ON Enjoy movie playback with suitable color temperature, sharp
subtitles and improved gradation for black, like in a theater.
OFF
Cancel the function.
When you set DVD THEATER STATUS to ON, PICTURE MODE,
WHITE BALANCE and AI ECO SENSOR / ECO MODE functions
are not available.
DVD SOUND MODE
You can choose different sound setting for viewing different types
of DVD content.
Select DVD SOUND MODE in DVD MENU under FEATURES menu,
then choose the desired setting.
MENU
MUSIC Select when watching a music concert.
USER
DRAMA Select when watching a drama movie.
THEATER Select when watching an action movie.
FEATURES menu
DVD SOUND MODE
Select if you want to adjust the sound setting to your preference.
DVD MENU
When you set DVD SOUND MODE in DVD MENU to USER,
you can adjust EQUALIZER under SOUND menu.
About the basic operations of the menu, please see the “How to
operate menus and menus locations” on page 5.
15
Customized setting
VNR
You can reduce the picture noise.
Select VNR in PICTURE menu, then choose a setting of VNR function.
MENU PICTURE menu
OFF VNR is turned off.
AUTO Effect of VNR is automatically controlled.
MIN Effect of VNR becomes minimum level.
MAX Effect of VNR becomes maximum level.
VNR
If you select MAX, the picture becomes softer even if the original
picture is sharp.
When you select VIDEO-2, you cannot adjust VNR function.
CLOSED CAPTION
If they are included in a program, you can view closed captions or
text information.
Press the CLOSED CAPTION button to select a setting.
OFF CLOSED CAPTION TEXT
To operate this function with a menu:
1
Select the CLOSED CAPTION in INSTALL menu, then choose
“CAPTION” or “TEXT”.
MENU INSTALL menu
2
Press the 2/3 button to select the desired caption or text channel.
CLOSED CAPTION
CHILD LOCK
You can disable the front control buttons of the TV.
Select CHILD LOCK in the FEATURES menu, then choose ON or
OFF.
MENU
FEATURES menu
CHILD LOCK
ON TIMER
You can set the TV to turn on automatically from standby mode at
a set channel and time.
1
Select ON TIMER in the FEATURE menu.
MENU FEATURES menu
ON TIMER
ON TIMER
CH 02
ON TIMER
00:15
The following display appears.
DISPLAY : BACK
TV/VIDEO : EXIT
2 Choose the CH (channel) by pressing the 2/3 button.
External input, AV position and any un-preset channel cannot be
chosen for CH.
3 Set the ON TIMER to your desired period of time by pressing the
2/3 button. ON TIMER starts. You can set the period of time to
a maximum of 12 hours in 15-minute intervals.
To off the ON TIMER, set the ON TIMER to OFF.
Note : If TV is not in standby mode when ON TIMER is reach the
setting time, this case is not available.
16
About the basic operations of the menu, please see the “How to
operate menus and menus locations” on page 5.
Customized setting (continued)
OFF TIMER
You can set the TV to turn off automatically to standby mode after
a set time.
Press the OFF TIMER button to select a desired period of time.
You can set the period of time to a maximum of 120 minutes in 10
minute intervals.
To operate this function with a menu:
MENU FEATURES menu OFF TIMER
When the remaining elapse time is one minute, “GOOD NIGHT!”
appears on the screen.
You can display the OFF TIMER menu again to confi rm or change
the remaining time.
VIDEO-2 SETTING
You can set the VIDEO-2 SETTING according to the video signal
output from external devices connected to the VIDEO-2 terminal.
Select VIDEO-2 SETTING in INSTALL menu, then choose a setting
(Factory setting is COMPONENT).
MENU INSTALL menu VIDEO-2 SETTING
VIDEO
COMPONENT If a component video signal (Y/CB/CR) is input.
You must choose a setting according to the signal that you input to
VIDEO-2. (If you input the VIDEO Signal or VCR Signal to VIDEO-2,
you must set VIDEO-2 SETTING to VIDEO.)
For connecting methods, see “Additional Preparation” on page 19.
If a normal video signal (composite video signal) is input.
BEEP
You can use the BEEP function to alert you during AUTO SIGNAL
DETECT, AI ECO SENSOR Detect, Stereo Detect, ON TIMER/OFF
TIMER operations and when some buttons on the remote control
are pressed.
Select BEEP in the INSTALL menu, then choose ON or OFF.
MENU
INSTALL menu
BEEP
When the volume is level 0, then BEEP function is not available.
DISPLAY
You can display the program number and video terminal number
on the screen.
Press the DISPLAY button to display the indication on the screen.
About the basic operations of the menu, please see the “How to
operate menus and menus locations” on page 5.
17
TV channel presetting
To register the TV channels automatically
(AUTO PROGRAM)
You can register the TV channels into the TV’s channel list
automatically.
1 Display the INSTALL menu.
MENU INSTALL menu
2 Choose AUTO PROGRAM, then press the MENU/OK button.
3 Press the 5/∞ button to select AIR or CABLE, then press the
MENU/OK button.
AUTO PROGRAM function starts, and the channels received are
registered automatically.
4 The CHANNEL SUMMARY menu appears.
CHANNEL SUMMARY
You can set undesired channels to be skipped.
Channels are to be skipped cannot be selected by the
CHANNEL -/+ button.
1 Display the INSTALL menu.
MENU INSTALL menu
2 Choose CHANNEL SUMMARY, then press the MENU/OK
button.
CHANNEL SUMMARY menu appears.
CHANNEL SUMMARY
CH/CC SKIP
■
CH 02
■
CH 03
■
CH 04
■
CH 05
CH 06
CH 07
CH 08
MENU : OK
✔
✔
■
SKIP
■
CANCEL
3 Choose the channel which you want to skip.
The skip can be set to all channels of AIR (CH02-CH69) and
CABLE (CC01-CC125).
4 Press the yellow button to skip the channel.
To cancel the skip, press the blue button.
5 Press the MENU/OK button to exit the menu.
18
About the basic operations of the menu, please see the “How to
operate menus and menus locations” on page 5.
Additional preparation
C
The illustrations shown in this section are for AV-21BA16 and AV29ST16 only, which are used for explanation purpose. Your TV may
not look exactly the same as illustrated.
Before connecting
• Read the manuals provided with the devices for the proper
connection.
• Turn off all the devices including the TV.
• Note that connecting cables are not supplied.
Connecting to front video input terminals
Front of TV
Headphones
AV-29ST16
RVL/MONO
IN(VIDEO-3)
AV-21BA16
VR
L / MONO
IN (VIDEO-3)
MENU
Camcorder or TV game
OK
Connecting to rear component/video input
terminals and output terminals
Rear of TV
AV-29ST16
COMPONENT
VIDEO-1
(VIDEO-2)
INPUT
S
OVER
V
L
/
R
MONO
Y
C
C
OUTPUT
INPUT
/
B
R
V
V
L
L
/
MONO
RR
When connecting to COMPONENT (VIDEO-2) input, depending on
the connection, choose the appropriate video input using the menu
(see “VIDEO-2 SETTING” on page 17)
VCR (for playing)
DVD player
(composite signals)
VCR (for recording)
DVD player
(component video
signals)
19
Troubleshooting
If a problem occurs when you are using the TV, check the below
troubleshooting guide before calling for repair.
• No picture, no sound • Deactivate the BLUE BACK function if it is turned
• Snowy picture
• Stripes appear on the
picture
• Double-pictures
(ghosting) occur
• Poor picture • Choose the appropriate color system. Refer to
• White and bright still
image look as if it
were colored
• Top of the image from
software products or
video tape is distorted
• Poor sound • Adjust the sound frequency properly. Refer to
• Stereo or SAP sound
is unclear
• Cannot operate the
remote control
• Cannot operate the
menus
• Cannot operate the
front control buttons
on.
•
Check the aerial cable and its connection with the TV.
• Interference occurs caused by other devices such as
an amplifi er, personal computer, or a hair drier. Move
such devices away from your TV.
• Interference occurs caused by signal reflecting
from mountains or building. Try to adjust the aerial’s
direction or use a better directionality antenna.
“COLOR SYSTEM” on page 9.
• Adjust the COLOR or BRIGHT setting. Refer to
“PICTURE SETTING” on page 10.
• Inevitable phenomenon due to the nature of the picture
tube. This is not a malfunction.
• This is due to the condition of the video signal whereby
the image was not recorded properly. This is not a
malfunction.
“EQUALIZER” on page 14.
• TV channel reception is poor. Change the stereo/ SAP
mode to mono sound (see page 13).
• The batteries may be exhausted. Replace with new
batteries (see page 7).
• Ensure that you are operating the remote control at
less than seven meters from the front of your TV.
• Press TV/VIDEO button to return to TV mode and try
operating the menus.
• Deactivate the CHILD LOCK function if it is turned on
(see page 16).
• Color patches appear
at the corner of the
screen
• Picture is tilted
• Image takes a short
period to be displayed
• TV may emit crackling
sound
• Feel a slight electric
shock when touching
the TV screen
• The Auto Signal
Detect function does
not work
• Suddenly, a channel
or input was
changed to VIDEO-2
inputs.
• “PLEASE
DISCONNECT
VIDEO-1 CABLE!”
appears on the
screen.
• This may due to the magnetized device such as a
speaker near to your TV. Keep the device apart from
your TV. Alternately, you can also use the magneticshielded speaker.
• This may due to the earth magnetism. Refer to
“PICTURE TILT” on page 11 to correct the tilt.
• Image required time to stabilize before display. This
is not a malfunction.
• This is due to a sudden change in temperature
and it is not a malfunction. If the crackling sound
is too frequent, request your service technician for
inspection.
• This is due to the static electricity of the picture tube
and it will not harm the human body. This is not a
malfunction.
• Please check that the AUTO SIGNAL DETECT
function is on or off.
• Turn the VCR or DVD player off, wait a while, then
turn it on again.
• Inspect the video cable connection on VIDEO-2 that
they are connected properly.
• Some VCRs and DVD players can trigger Auto Signal
Detect even after you choose a different input.
• Please turn off the AUTO SIGNAL DETECT
function.
• Please disconnect either S-VIDEO cable or video input
cable from Video-1 input.
20
Specifi cations
TV RF systems
M
Color systems
TV mode: NTSC 3.58 MHz
VIDEO mode: PAL, SECAM, NTSC 3.58 MHz, NTSC 4.43 MHz
Receiving channels
VHF low channel (VL), VHF high channel (VH), UHF channel (U)
Receives cable channels in mid band, super band and hyper band.
Power requirements
AC 110 to 240 V, 50 Hz / 60 Hz
External input / output
VIDEO-1: S-video input, VIDEO input, AUDIO L/R input
VIDEO-2/COMPONENT: VIDEO input, AUDIO L/R input, COMPONENT VIDEO (Y/C
VIDEO-3: VIDEO input, AUDIO L/R input
OUTPUT: VIDEO output, AUDIO L/R output
Headphone jack: Stereo mini jack (3.5 mm diameter)
Sound-multiplex systems
MTS (Multi-channel Television Sound) (Except AV-29BA16, AV-21BA16)
AV STEREO (For AV-29BA16, AV-21BA16 only)
Viewing Screen Size (Visible area)
AV-21BA16 508 mm
AV-21MT16 508 mm
AV-21VT16 508 mm
AV-25MT16 600 mm
AV-29BA16 676 mm
AV-29MT16 676 mm
AV-29VT16 676 mm
AV-29ST16 676 mm
B/CR
) input
Design and specifi cations subject to change without notice.
21
MEMO
22
MEMO
23
© 2006 Victor Company of Japan, Limited
0606-FLE-JMT
Loading...