JVC AV21BF5EES, AV21BF5ENS Service Manual

A
A
SERVICE MANUAL
COLOUR TELEVISION
AV21BF5ENS
AV21BF5EES
V21BF5ENS V21BF5EES
CONTENTS
SPECIFICATIONS
SAFETY PRECAUTIONS
FEATURES
MAIN DIFFERENCE LIST
SPECIFIC SERVICE INSTRUCTIONS
SERVICE ADJUSTMENTS
PARTS LIST
OPERATING INSTRUCTIONS
STANDARD CIRCUIT DIAGRAM
1
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
COPYRIGHT © 2002 VICTOR COMPANY OF JAPAN, LTD.
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・
・・・・・・
2 4 5 5 6 9
17
2-1
No.51879 Jan. 2002
A
V21BF5ENS
A
V21BF5EES

SPECIFICATIONS

ITEM
Content
AV21BF5ENS AV21BF5EES
Dimensions (WxHxD)
Weight
TV RF System
Colour System
Teletext System
Stereo System
Tuning System
Number Of C H memory position
Receiving Frequency
Intermediate Frequency
Colour Sub Carrier Frequency
Aerial Input Terminal
Power Input
Power Consumption
Picture Tube
High Voltage
Speaker
Audio Output
Input
Output
Input Terminal
Output Terminal
Remote Control Unit
TV Mode
Video Mode
VHF (VL)
VHF (VH)
UHF
CATV
VIF Carrier
SIF Carrier
Video
S/Video
Audio (L/R)
Video
Audio (L/R)
Rear Side
Front Side
Front Side
Rear Side
60 x 45 x 48 cm
22.2 kg
B/G B/G, D/K, K1
PAL PAL / SECAM
PAL / SECAM / NTSC 3.58 / NTSC 4.43
Fastext / Topt ext
A2 / NICAM
Frequenc y Synthesizer T uning System
100 ch
46.25MHZ ~ 168.25MHz
175.25MHz ~ 463. 25MHz
471.25MHz ~ 863. 25MHz
Super (S11-S20) & Hyper (S21-S41) bands receivable
38.9MHz
32.4MHz (6.5MHz)
32.9MHz (6.0MHz)
33.4MHz (5.5MHz)
PAL (4.43MHz), SECAM (4.43MHz), NTSC (3.58MHz/4.43MHz)
75 Ohm Unbalanc ed
AC 220 ~ 240V, 50Hz
95W(Max.)/73W (Avg.) Stand-by<5W
21 inch measured diagonally
27kV (in cut-off service mode)
57x160 mm oval type x2
8W +8W
1Vp-p, 75 Ohm
Y: 1Vp-p Positive C: 0.286Vp-p
500 mVrms, High Impedance
1 Vp-p, 75 Ohm
500 mVrms, Low Impedance
AV1 (Video/Audio/RGB)
AV2 (Video/Audio/S-VHS)
AV3 (Video/Audio)
Headphone jack (Stereo mini jack 3.5)
AV1 (Video/Audio)
AV2 (Video/Audio) (Selected TV, AV1 or AV3)
RM-C85, Battery size:AAA/R03 x 2
Design & specifications are subject to change without notice.
2
No.51879
A
A
■■■■
21-pin Euro connector (SCART socket) : AV-1 / AV-2
(P-P= Peak to Peak, S-W= Sync tip to white peak, B-W= Blanking to white peak)
Pin No.
Signal Designation Matching Value AV-1 AV-2
1 AUDIO R output 500mVrms(Nominal),Low impedance
2 AUDIO R input 500mVrms(Nominal),High impedance
3 AUDIO L output 500mVrms(Nominal),Low impedance
4 AUDIO GND
V21BF5ENS
V21BF5EES
(TV OUT)
○○
(TV OUT)
○○
(TV/LINE OUT)
(TV/LINE OUT)
5 GND (B)
6 AUDIO L input 500mVrms(Nominal), High impedance
7B input
FUNCTON SW
8
(SLOW SW)
9 GND (G)
10 - NC -
11 G input
12
- NC -
13 GND (R)
14 GND (YS)
15 R / C input
16 Ys input
17 GND(VIDEO output)
18 GND(VIDEO input)
19 VIDEO output
20 VIDEO / Y input
700mV
Low : 0-3V, High : 8-12V, High impedance
700mV
R : 700mV C : 300mV
Low : 0 – 0.4, High : 1 - 3V, 75
1V
1V
, 75
B-W
Ω○
, 75
B-W
Ω○
, 75
B-W
Ω
, 75
P-P
Ω
(Negative going sync), 75
S-W
(Negative going sync), 75
S-W
Ω○
Ω
Ω○
○○
○○
○○
○○
(R/C)
○○
○○
(TV)
(TV/LINE OUT)
NC
NC
NC
NC
(only C)
NC
21 COMMON GND
[
Pin assignment
]
No.51879
○○
3
A
V21BF5ENS
A
V21BF5EES

SAFETY PRECAUTIONS

1. The design of this product contains special hardware, many circuits and components specially for safety purposes. For continued protection, no changes should be made to the original design unless authorized in writing by the manufacturer. Replacement parts must be identical t o those us ed in the original circuits. Service should be performed by qualified personnel only.
2. Alterations of the design or circuitry of the products should not be made. Any design alterations or additions will void the manufacturer's warranty and will further relieve the manufacturer of responsibility for personal injury or property damage resulting theref rom.
3. Many electric al and mechanical parts in the products have special safety-related characteristics. These characteristics are often not evident from visual inspection nor can t he protection afforded by them necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in the parts list of Service manual.
components having such features are identified by shading on the schematics and by ( manual.
have the s ame safety characteristics as the recommended replacement part shown in the parts list of S ervice manual may cause shock, fire, or other hazards.
The us e of a substitute replacement which does not
) on the parts list in Service

Electrical
4.
Don't short between the LIVE side ground and ISOLATED (NEUTRAL) side ground or EARTH side ground when repairing.
Some model's power circuit is partly different in the GND. The differenc e of the GND is shown by the LIVE side GND, the ISOLATED(NEUTRAL) side GND and EARTH side GND. Don't short between the LIVE side GND and ISOLATED(NEUTRAL) side GND or EARTH side GND and never measure with a measuring apparatus (oscilloscope etc.) the LIVE side GND and ISOLATED(NEUTRAL) side GND or EARTH side GND at the same time. If above note will not be kept, a fuse or any parts will be broken.
5. If any repair has been made to the chassis, it is recommended that the B1 setting should be checked or adjusted (See ADJUSTMENT OF B1 POWER SUPPLY).
6. The high voltage applied to the picture tube must conform with that specified in Servic e manual. E xcessive high voltage can cause an incr ease in X-Ray emission, arcing and possible component damage, therefore operation under excessive high voltage conditions should be kept to a minimum, or should be prevented. If s evere arcing occurs, remove the AC power immediately and determine the cause by visual inspection (incorrect installation, cracked or melted high voltage harness, poor soldering, etc.). To maintain the proper minimum level of soft X-Ray emission, components in the high voltage circuitr y including the picture tube must be the exact replacements or alternatives approved by the manufacturer of the c omplete product.
7. Do not check high voltage by drawing an arc. Use a high voltage meter or a high voltage probe with a VT VM. Discharge the picture tube before attempting meter connection, by connecting a clip lead to the ground frame and connecting the other end of the lead through a 10k: 2W resistor to the anode button.
8. W hen service is required, observe the original lead dress. Extra precaution should be given to assure c orrect lead dress in the high voltage circuit area. Where a short circuit has occ urred, those components that indicate evidence of overheating should be replaced. Always use the manufacturer's replacement components.
9.
Isolation Check (Safety for Electrical Shock Hazard)
After re-assembling the product, always perform an isolation check on the exposed metal parts of the cabinet (antenna terminals, video/audio input and output terminals, Control knobs, metal c abinet, screwheads, earphone jack, control shafts, etc.) to be sure the product is safe to operate without danger of electr ic al shock.
(1)
Dielectric Strength Test
The isolation between the AC primary circuit and all metal parts exposed to the user, particularly any exposed metal part having a return path to the chassis should withstand a voltage of 3000V AC (r.m.s.) for a period of one second.
(. . . . Withstand a voltage of 1100V AC (r.m.s.) to an appliance
rated up to 120V, and 3000V AC (r.m.s.) to an appliance rated 200V or more, for a period of one second.) This method of test requires a test equipment not generally found in the s ervice trade.
(2)
Leakage Current Check
Plug the AC line cord directly into the AC outlet (do not use a line isolation transformer during this check.). Using a "Leakage Current T ester", measure the leakage current from each exposed metal part of the cabinet, particularly any exposed metal part having a return path to the chassis, to a known good earth ground (water pipe, etc.). Any leakage curr ent must not exceed
0.5mA AC (r.m.s.). However, in tropical area, this must not exceed 0.2mA AC (r.m.s.).
Alternate Check M ethod
zzzz
Plug the AC line cord directly into the AC outlet (do not use a line isolation transf ormer during this check.). Use an AC voltmeter having 1000 ohms per volt or more sensitivity in the following manner. Connect a 1500: 10W resistor paralleled by a 0.15PF AC-type capacitor between an exposed metal part and a known good earth ground (water pipe, etc.). Measure the AC voltage across the resistor with the AC voltmeter. Move the resistor connection to each exposed metal part, particularly any exposed metal part having a retur n path to the chassis, and measure the AC voltage across the resistor. Now, reverse the plug in the AC outlet and repeat each measurement. Any voltage measured must not exceed 0.75V AC (r.m.s.). This corresponds to 0.5mA AC (r.m.s.). However, in tropical ar ea, this must not exceed 0.3V AC ( r.m.s.). This corresponds to 0.2mA AC (r.m.s.).
AC VOLTMETER
0.15μF AC-T YPE
1500
GOOD EARTH GROUND
:
(HAVING 1000 OR MORE SENSITIVITY)
10W
/V,
:
PLACE THIS PROBE ON EACH EXPOSED METAL PART
4
No.51879
A
A

FEATURES

V21BF5ENS
V21BF5EES
1. It is a remote controlled c olor television.
2. 100 programs from VHF, UHF bands or cable channels can be preset.
3. It can tune cable channels.
4. Controlling the TV is very easy by its menu driven s ystem.
5. It has two Euroconnector s ockets f or external device (such as video recorder, video games, audio set, etc.)
6. Front AV Input available.
7. Stereo sound syst ems (German + Nicam) ar e available.
8. Full function Teletext (F astext, Toptext).
9. It is possible to connect headphone.
10. Direct channel access.
11. APS (Automatic Programming System).
12. All programs can be named.
13. Forward or backward automatic tuning.
14. Automatic sound mute when no transmission.
15. 5 minutes after the broadcasting (closedown), the TV switches itself automatic ally to stand-by mode.

MAIN DIFFERENCE LIST

MODEL No.
Parts Name
MAIN PWB VE-20073855 VE-20073865
AV21BF5ENS AV21BF5EES
F CARTON BOX VE-20074340 VE-20074390
INST BOOK VE-50021021 VE-50021020
RATING LABEL VE-20074339 VE-20074389
TV RF system B/G B/G, D/K, K1
Colour system (TV MODE)
PAL PAL / SECAM
No.51879
5
A
V21BF5ENS
A
V21BF5EES

SPECIFIC SERVICE INSTRUCTIONS

DISASSEMBLY PROCEDURE
REMOVING THE REAR COVER
1. Remove the 6 screws marked A.
2. Withdraw the rear cover toward you.
A
REMOVING THE SPEAKER
After removing the rear cover.
z
1. Remove the 4 screws marked B as shown in the figure.
2. Remove the speaker.
3. Remove the other hand speaker same step.
REAR COVER
MAIN PWB
PICTURE TUBE
B
SPEAKER ( LEFT & RIGHT )
FRONT CABINET
6
No.51879
A
A
SETTING OF THE LAST MEMORY FOR SHIPMENT
■■■■
USER SETTING VALUES
Setting Item Setting Value Setting Item Setting Value
SOUND MENU FEATURE MENU
BASS CENTER SLEEP TIMER OFF
V21BF5ENS
V21BF5EES
TREBLE
BALANCE
EFFECT OFF
PICTURE MENU INSTALL TV CONFIG. MENU
BRIGHTNESS LANGUAGE ENGLISH
COLOUR COUNTRY ?
CONTRAST AV-2 OUTPUT TV
SHARPNESS
HUE (only NTSC)
PICTURE MODE AUTO
SETTING APS BIT IN SERVICE MENU
1) Enter s ervice menu in TV mode by pressing “INFO ” and “MUTING” keys simultaneously. Service Menu will appear.
2) Select OPTIONS by pressing Up/Down keys on remote control unit.
3) Enter OPTIONS by pressing Left/Right keys on remote control unit.
4) Select OPTION 8 by pressing Up/D own keys on remote control unit.
5) Selected bit in one OPTION is shown by blinking character. Select B2 by pressing Left/Right keys on remote contr ol unit. DO NOT CHANGE ANY OTHER BIT.
6) Press digit key “1” to s et APS bit.
7) Press “STANDARD” key on remote contr ol unit to exit s ervice mode.
These adjust are automatically
restored when APS bit in Service
menu is s et.
The proc edure f or setting APS
bit is described bellow.
CHILD LOCK OFF
No.51879
7
A
V21BF5ENS
A
V21BF5EES
REPLACEMENT OF CHIP COMPONENT
CAUTIONS
1. Avoid heating for more than 3 seconds.
2. Do not rub the electr odes and the resist parts of the pattern.
3. W hen removing a chip part, melt the solder adequately.
4. Do not reuse a chip part after removing it.
SOLDERING IRON
1. Use a high insulation soldering iron with a thin pointed end of it.
2. A 30w soldering iron is recommended for easily removing parts.
REPLACEMENT STEPS
How to remove Chip parts
1.
Resistors, capacit ors, etc.
(1) As shown in the figure, pus h the part with tweezers and
alternately melt the solder at each end.
2. How to install Chip parts
Resistors, capacit ors, etc.
(1) Apply solder to the pattern as indicated in the figure.
(2) Shift with tweezers and remove the chip part.
Transistors, diodes, variable resistors, etc.
(1) Apply extra s older to each lead.
SOLDER
(2) As shown in the figure, pus h the part with tweezers and
alternately melt the solder at each lead. Shift and remove the chip part.
SOLDER
(2) Grasp the chip part with tweezers and place it on the
solder. Then heat and melt the solder at both ends of the chip part.
Transistors, diodes, variable resistors, etc.
(1) Apply solder to the pattern as indicated in the figure. (2) Grasp the chip part with tweezers and place it on the
solder.
(3) First solder lead
(4) Then solder leads
as indicated in the figur e.
A
A
B
C
and C.
B
A
B
Note : After remov ing the part, remove remaining solder from
the pattern.
8
No. 51879
C
A
A

SERVICE ADJUSTMENTS

ADJUSTMENT PREPARATION
1. You can make the necessary adjustments for this un it with
either the Remote Control Unit or With the adjustment tools and parts as given below.
2. Adjustment with the Remote Control Unit is made on the
basis of the initial setting values, however, the new setting values which set the scr een to its optimum condition may differ from the initial settings.
3. Make sure that AC power is turned on correctly.
4. Turn on the power for set and test equipment before use, and
start the adjustment procedures after waiting at least 30 minutes.
5. Unless otherwise specified, prepare the most suitable reception
or input signal f or adjustment.
6. Never touch any adjustment parts which are not specified in the list for this adjust ment - var iable resistors, transformers, condensers, etc.
7. Presetting before adjustment. Unless otherwise specified in the adjustment instructions, preset the following functions with the r emote c ontrol unit:
VIDEO STATUS STANDARD
TINT/COLOR
PICTURE/BRIGHT
DETAIL
V21BF5ENS
V21BF5EES
CENTER
ADJUSTMENT EQUIPMENT
1. DC voltmeter (or digital voltmeter)
2. Signal generator (Pattern generator)[PAL/SECAM/NTSC
3. Remote c ontrol unit
MAIN PARTS LOCATIONS
REMOCON RECEIVER
LED
IC502
MEMOR Y IC
MENU
IC501
MICOM
(+)
(+) (-)
(+)(+)
(-)
(-)(-)
PROG
/Ch.
(+)
(+) (-)
(+)(+)
VOL
(-)
(-)(-)
MAIN POWER SW
FBT
MULTI SOUND PWB
SCART
jack
TUNER
AV-1 AV-2
SCART
jack
No. 51879
(Indicated [150/115V]
B1
on the bottom side)
UPPER : FOCUS VR LOWER : SCREEN VR
9
A
V21BF5ENS
A
A
A
V21BF5EES
BASIC OPERATION SERVICE MENU:
■■■■
HOW TO ENTER THE SERVICE MODE
1) Press the CONTROL UNIT, simultaneously.
■■■■
SELECTION OF ADJUSTMENT ITEMS
1) Press the UP ( ) or
ADJUSTMENT ITEM.
2) Press the
ADJUSTMENT SCREEN.
3) To change the selected P arameter, use
LEFT
HOW TO EXIT SERVICE MODE
1) Press the
INFORMATION
RIGHT
( ) key.
STANDARD
key and
( ) or
Key on REMOTE CONTROL UNIT.
MUTING
( ) key and select the
DOWN
LEFT
key of REMOTE
( ) key and enter
( ) and
RIGHT
SERVICE MENU ITEM
PARAMETER VALUE
SERVICE
DJUST…..
OPTIONS…..
SERVICE MENU SCREEN
ADJUST
***
OUT UP
*** ******
ADJUSTMENT SCREEN
DJUST No.
PARAMETER
■■■■
ADJUSTMENT SERVICE MENU
ADJUSTMENT ITEM
AGC 03 AGC
IF-PLL NEGATIVE 04 IF-PLL Negative
IF-PLL POSITIVE 05 IF-PLL Positive
4 : 3 HORIZONTAL SHIFT
VERTICAL SLOPE
VERTICAL AMPLITUDE
ADJUST
No.
00 White Point RED
01 White Point GREENWHITE BALANCE
02 White Point BLUE
06 Y-Delay PAL
07 Y-Delay SECAMLUMINANCE DELAY
08 Y-Delay NTSC
12 4 : 3 PICTURE MODE
23 16 : 9 PICTURE MODE
13 4 : 3 PICTURE MODE
24 16 : 9 PICTURE MODE
14 4 : 3 PICTURE MODE
25 16 : 9 PICTURE MODE
DISCRIPTION
MUTING key
UP / DOWN (
) key
/
REMOTE CONTROL UNIT key NAME
STANDARD key
RIGHT / LEFT (
/
) key
INFORMATION key
10
No. 51879
A
A
ADJUSTMENTS
Item
SCREEN VOLTAGE Adju stment
Measurin g instrument
Signal Generator
Remote Control unit
SERVICE
ADJUST…..
OPTIONS…..
Test point Adjustment part Description
SERVICE MENU
SCREEN VR
[FBT]
OPTION 02
V21BF5ENS
V21BF5EES
1. Receive a
2. Enter the option settings in the SERVICE MENU.
3. Press the UP / DOW N (
4. To change bit 6, come on to it by using L / R ( make it “1” by pressing “1” white bit 2 is blinking.
5. Observe the thin horizontal blue-white line in the middle of the
screen, and adjust the lower VR of the FBT, until the line is in its thinnest visible thickness.
6. Then make Option 02 bit 6 “0” , by pressing “ 0” on the r emote
control unit, although you do not see any picture.
PAL
colour bar.
/
) key, and Enter
Option 02
) key and
/
.
FOCUS Adju stment
SELECT OPTION menu
FBT
FOCOUS
SCREEN
Signal generator
FOCUS VR
[FBT]
1. Receive a
2. Adjust the upper VR of the FBT, until you get the Optinum
focus, the sharpest picture.
circle pattern.
PAL
B1 VOLTAGE check
DC Voltmeter
Marked
[150/115V] on the MAIN PWB
No. 51879
1. Check whether the voltage at the point named and silk
screened as “150 / 115V” on the MAIN PW B is 150V DC.
11
A
V21BF5ENS
A
V21BF5EES
Item
WHITE BALANCE
AGC Adju stmentDCvoltmeter
Measurin g
instruments
Signal generator
Test point Adjustment part Description
ADJUST 00 (White point
- RED)
ADJUST 01
(White point
- GREEN)
ADJUST 02 (White point
- BLUE)
ADJUST 03
[LOW LIGHT]
1. Receive a whole black signal.
2. Adjust the <Adjust 00>, <Adjust 01>, <Adjust 02>, in the SERVICE MENU s o that the entire screen do not shine black.
[HIGH LIGHT]
1. Receive a white and black signal (colour off).
2. Adjust the <Adjust 00>, <Adjust 01>, <Adjust 02>, in the SERVICE MENU so that the whiteness in the screen become sharp.
1. Receive a any broadcast.
2. Select
3. Connect a DC voltmeter to pin 1 of the tuner. Change the
<ADJUST 03>
AGC parameter until you see 3.70V DC on voltmeter display.
from SERVICE MENU
IF-PLL NEGATIVE Adju stment
IF-PLL POSITIVE Adju stment
ADJUST 04
ADJUST 05
1. Select
2. Adjustment value is set to 80 as a default value.
<ADJUST 04>
from SERVICE MENU.
1. Select
2. Adjustment value is set to 80 as a default value.
<ADJUST 05>
from SERVICE MENU.
12
No. 51879
A
V21BF5ENS
A
V21BF5EES
Item
LUMINANCE DELAY Adju stment
Measurin g
instruments
Signal generator
Test point Adjustment part Description
Adjust 06 [ Y-Delay PAL ]
1. Receive a
2. Select
3. Adjust bar of the pattern become as sharper and colours between transients do not mix with each other as possible.
Note: If the SAW filter is one of the G1965M, J1951M, K2958M,
K2962M, G3957M, K6256K, K6259K or M1963M, there is constant group delay distortion, so for an equal delay of the luminance and chrominance signal the delay must be set at a value of 160nS. This means the adjustment must be set to the maximum value.
Adju st 07 [ Y-Delay SECAM ]
1. Receive a
2. Select
3. Adjust colour bar of the pattern become as sharper and colours between transients do not mix with each other as possible.
Note: If the SAW filter is one of the G1965M, K2958M,
K2962M, G3957M, K6256K or K6259K, there is constant group delay distortion, so for an equal delay of the luminance and chrominance signal the delay must be set at a value of 160nS. This means the adjustment must be set to the maximum value.
colour bar signal.
PAL <Adjust 06> Y-Delay PAL
SECAM <Adjust 07>
Y-Delay SECAM
from SERVICE MENU.
till the colour transients on the colour
colour bar signal.
from SERVICE MENU.
till the colour transients on the
Adju st 08 [ Y-Delay NTSC ]
1. Receive a
2. Select
3. Adjust bar of the pattern become as sharper and colours between transients do not mix with each other as possible.
Note: If the SAW filter is M1963M, there is constant group delay
NTSC <Adjust 08> Y-Delay NTSC
distortion, so for an equal delay of the luminanc e and chrominance signal the delay must be set at a value of 160nS. This means the adjustment must be set to the maximum value.
colour bar signal.
from SERVICE MENU.
till the c olour transients on the colour
No. 51879
13
A
V21BF5ENS
A
V21BF5EES
Item
4 : 3
HORIZONTAL SHIFT Adju stment
VERTICAL SLOPE Adju stment
Measurin g
instruments
Signal generator
Signal generator
Test point Adjustment part Description
Adjust 12 ( 4 : 3 )
Adjust 23 ( 16 : 9 )
Adjust 13 ( 4 : 3 )
Adjust 24 ( 16 : 9 )
1. Receive a
2. Set
< 4 : 3 aspect mode >
3. Select
4. Change horizontal shift till the picture is horizontally
5. Set
6. Adjusts with the step which is the s ame above from 3 to 4
1. Receive a cross-hatch signal.
2. Set
3. Select
4. Change vertic al slope till the size of squares on both the
5. Set
6. Adjusts with the step which is the s ame above from 3 to 4
< ADJUST 12 >
centered. Check whether this adjustment is c orrect after completing Servic e Mode Adjustment.
< 16 : 9 aspect mode >
about the 16 : 9 aspect mode, too.
< 4 : 3 aspect mode >
< ADJUST 13 >
upper and lower part of test pattern become equal to the squares laying on the vertical centre of the test pattern. Check and readjust VERTICAL SLOPE item if the adjustment becomes improper after some other geometric adjustments are done.
< 16 : 9 aspect mode >
about the 16 : 9 aspect mode, too.
RED
test pattern.
.
from SERVICE MENU.
.
.
from SERVICE MENU.
.
VERTICAL
AM PLITU DE Adju stment
Signal generator
Adjust 14 ( 4 : 3 )
Adjust 25 ( 16 : 9 )
1. Receive a
2. Set
< 4 : 3 aspect mode >
3. Select
4. Change vertical slope till horizontal black lines on both the
5. Set
6. Adjusts with the step which is the s ame above from 3 to 4
< ADJUST 14 >
upper and lower part of the test pattern become very close to the upper and lower horizontal sides of picture tube and nearly about to disappear. Check and readjust VERTICAL AMPLITUDE item if the adjustment becomes improper after some other geometric adjustments are done.
< 16 : 9 aspect mode >
about the 16 : 9 aspect mode, too.
test pattern signal.
PAL
.
from SERVICE MENU.
.
14
No. 51879
A
V21BF5ENS
A
V21BF5EES
Item
S-CORRECTION Adju stment
VERTICAL
SHIFT
Adju stment
Measurin g
instrument
Signal generator
Signal generator
Test point Adjustment part Description
Adjust 15 ( 4 : 3 )
Adjust 26 ( 16 : 9 )
Adjust 16 ( 4 : 3 )
Adjust 27 ( 16 : 9 )
7. Receive a
8. Set
< 4 : 3 aspect mode >
9. Select
10. Change S-correction till the middle part of the circle is round
11. Set
12. Adjusts with the step which is the same above from 3 to 4
1. Receive a
2. Set
3. Select
4. Change Vertic al Shift till the t est pattern is vertically c entred,
5. Set
6. Adjusts with the step which is the same above from 3 to 4
< ADJUST 15 >
as possible.
< 16 : 9 aspect mode >
about the 16 : 9 aspect mode, too.
in the top and the bottom and on either side to find ).
< 4 : 3 aspect mode >
< ADJUST 16 >
i.e. horizontal line at the centre pattern is in equal distanc e both to upper and lower side of the picture tube. Check and readjust Vertical Shift item if the adjustment becomes improper after some other geometric adjustments are done.
< 16 : 9 aspect mode >
about the 16 : 9 aspect mode, too.
circle pattern signal.
PAL
.
from SERVICE MENU.
.
test pattern signal ( or the symmetrical signal
PAL
.
from SERVICE MENU.
.
No. 51879
15
A
V21BF5ENS
A
V21BF5EES
[MEMO]
16
No. 51879
Loading...