JVC AV-14F704 Service Manual

SERVICE MANUAL

COLOR TELEVISION

AV-14F704

VOL

CONTENTS

q SPECIFICATIONS.............................................................................................................................................. 2

q OPERATING INSTRUCTIONS (APPENDIX)

q SAFETY PRECAUTIONS .................................................................................................................................. 3

q SPECIFIC SERVICE INSTRUCTIONS .............................................................................................................. 4

q SERVICE ADJUSTMENTS ................................................................................................................................ 8

q GUIDE FOR REPAIRING ................................................................................................................................. 13

q STANDARD CIRCUIT DIAGRAM ................................................................................................................... 2-1

q PARTS LIST ..................................................................................................................................................... 19

No. 52130

2003/05

AV-14F704

SPECIFICATIONS

TELEVISION

Picture Tube: 14” (measured diagonally)

Color System: NTSC

TV RF System: US System M

Tuner Type: 181 Channel, Quartz PLL Frequency Synthesized

Receiving Channels: VHF 2-13

UHF 14-69

CATV 01-97 (5A)-(A-3)

98-99 (A-2)-(A-1)

14-22 (A)-(I)

23-36 (J)-(W)

37-65 (AA)-(FFF)

66-125 (GGG)-(125)

Intermediate Frequency: Picture (FP) : 45.75 MHz

Sound (FS) : 41.25 MHz

FP-FS : 4.50 MHz

Antenna Input: VHF/UHF/CATV In 75 ohms coaxial, F-Type Connector

Speaker: 1-5/8” (4 cm) x 2-13/16” (7 cm), 8 ohms x 2

Audio Output Power: 2.5 W + 2.5 W

GENERAL

Power Source: 120 V AC, 60 Hz

Power Consumption: 80 Watts

Dimensions(W x H x D): 17-1/8” (432 mm) x 13-5/8” (344.5 mm) x 15-1/2” (393.5 mm)

Weight: 26.4 Ibs/12 kg

Video/Audio Inputs: Component input

Y input: 1.0 Vp-p, 75 ohm (RCA pin jack)

Pb, Pr input : 0.7 Vp-p, 75 ohm (RCA pin jack)

S-Video input

Y input: 1.0 Vp-p, 75 ohm

C input: 0.3 Vp-p, 75 ohm

Video input: 1.0 Vp-p, 75 ohm (RCA pin jack)

Audio input: -8dB, 47 kohm (RCA pin jack)

Headphone Jack: 3.5 mm mini-jack

Storage Temperature -20 ºC ~ 60 ºC

Operating Temperature 5 ºC ~ 40 ºC

Accessories:

Remote Control X 1

Batteries (UM-3) X 2

Design & specification are subject to change without notice.

No. 52130

SAFETY PRECAUTIONS

SERVICING NOTICES ON CHECKING

AV-14F704

1. KEEP THE NOTICES

As for the places which need special attentions, they are

indicated with the labels or seals on the cabinet, chassis and

parts. Make sure to keep the indications and notices in the

operation manual.

2. AVOID AN ELECTRIC SHOCK

There is a high voltage part inside. Avoid an electric shock

while the electric current is flowing.

3. USE THE DESIGNATED PARTS

The parts in this equipment have the specific characters of

incombustibility and withstand voltage for safety. Therefore,

the part which is replaced should be used the part which has

the same character.

Especially as to the important parts for safety which is

indicated in the circuit diagram or the table of parts as a

mark, the designated parts must be used.

4. PUT PARTS AND WIRES IN THE ORIGINAL POSITION AFTER ASSEMBLING OR WIRING

There are parts which use the insulation material such as a

tube or tape for safety, or which are assembled in the condition

that these do not contact with the printed board. The inside

wiring is designed not to get closer to the pyrogenic parts and

high voltage parts.

Therefore, put these parts in the original positions.

5. TAKE CARE TO DEAL WITH THE CATHODE-RAY TUBE

In the condition that an explosion-proof cathoderay tube is set

in this equipment, safety is secured against implosion.

However, when removing it or serving from backward, it is

dangerous to give a shock. Take enough care to deal with it.

6. AVOID AN X-RAY

Safety is secured against an X-ray by considering about the

cathode-ray tube and the high voltage peripheral circuit, etc.

Therefore, when repairing the high voltage peripheral circuit,

use the designated parts and make sure not modify the

circuit.

Repairing except indicates causes rising of high voltage, and

it emits an X-ray from the cathoderay tube.

7. PERFORM A SAFETY CHECK AFTER SERVICING

Confirm that the screws, parts and wiring which were

removed in order to service are put in the original positions, or

whether there are the portions which are deteriorated around

the serviced places serviced or not. Check the insulation

between the antenna terminal or external metal and the AC

cord plug blades. And be sure the safety of that.

(INSULATION CHECK PROCEDURE)

1. Unplug the plug from the AC outlet.

2. Remove the antenna terminal on TV and turn on the TV.

3. Insulation resistance between the cord plug terminals and

the eternal exposure metal [Note 2] should be more than

1M ohm by using the 500V insulation resistance meter

[Note 1].

4. If the insulation resistance is less than 1M ohm, the

inspection repair should be required.

[Note 1]

If you have not the 500V insulation resistance meter, use a

Tester.

[Note 2]

External exposure metal:Antenna terminal

Earphone jack

HOW TO ORDER PARTS

Please include the following informations when you order parts. (Particularly the VERSION LETTER.)

1. MODEL NUMBER and VERSION LETTER The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be found at the end of the SERIAL NUMBER.

2. PART NO. and DESCRIPTION You can find it in your SERVICE MANUAL.

IMPORTANT

Inferior silicon grease can damage IC's and transistors. When replacing an IC's or transistors, use only specified silicon grease (YG6260M). Remove all old silicon before applying new silicon.

No. 52130

AV-14F704

SPECIFIC SERVICE INSTRUCTIONS

DISASSEMBLY INSTRUCTIONS

1. REMOVAL OF ANODE CAP

Read the following NOTED items before starting work.

* After turning the power off there might still be a potential voltage

that is very dangerous. When removing the Anode Cap, make sure to discharge the Anode Cap's potential voltage.

* Do not use pliers to loosen or tighten the Anode Cap terminal,

this may cause the spring to be damaged.

REMOVAL

1. Follow the steps as follows to discharge the Anode Cap.

(Refer to Fig. 1-1.)

Connect one end of an Alligator Clip to the metal part of a flatblade screwdriver and the other end to ground. While holding the plastic part of the insulated Screwdriver, touch the support of the Anode with the tip of the Screwdriver. A cracking noise will be heard as the voltage is discharged.

GND on the CRT

3. After one side is removed, pull in the opposite direction to remove the other.

NOTE

Take care not to damage the Rubber Cap.

INSTALLATION

1. Clean the spot where the cap was located with a small amount of alcohol. (Refer to Fig. 1-3.)

NOTE

Confirm that there is no dirt, dust, etc. at the spot where the cap was located.

Location of Anode Cap

Fig. 1-3

2. Arrange the wire of the Anode Cap and make sure the wire is not twisted.

3. Turn over the Rubber Cap. (Refer to Fig. 1-4.)

Screwdriver

Support

CRT

Alligator Clip

GND on the CRT

2. Flip up the sides of the Rubber Cap in the direction of the arrow and remove one side of the support.

(Refer to Fig. 1-2.)

Fig. 1-1

Rubber Cap

CRT

Support

Fig. 1-2

Fig. 1-4

4. Insert one end of the Anode Support into the anode button, then the other as shown in Fig. 1-5.

Support

CRT

5. Confirm that the Support is securely connected.

6. Put on the Rubber Cap without moving any parts.

Fig. 1-5

No. 52130

AV-14F704

2. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC

REMOVAL

1. Put the Masking Tape (cotton tape) around the Flat Package IC

to protect other parts from any damage.

(Refer to Fig. 2-1.)

NOTE

Masking is carried out on all the parts located within 10 mm distance from IC leads.

Masking Tape (Cotton Tape)

2. Heat the IC leads using a blower type IC desoldering machine.

(Refer to Fig. 2-2.)

NOTE

Do not add the rotating and the back and forth directions force on the IC, until IC can move back and forth easily after desoldering the IC leads completely.

Fig. 2-1

Blower type IC desoldering machine

3. When IC starts moving back and forth easily after desoldering completely, pickup the corner of the IC using a tweezers and remove the IC by moving with the IC desoldering machine.

(Refer to Fig. 2-3.)

NOTE

Some ICs on the PCB are affixed with glue, so be careful not to break or damage the foil of each IC leads or solder lands under the IC when removing it.

Blower type IC desoldering machine

Tweezers

Fig. 2-3

4. Peel off the Masking Tape.

5. Absorb the solder left on the pattern using the Braided Shield Wire. (Refer to Fig. 2-4.)

NOTE

Do not move the Braided Shield Wire in the vertical direction towards the IC pattern.

Braided Shield Wire

Soldering Iron

Fig. 2-2

No. 52130

IC pattern

Fig. 2-4

AV-14F704

INSTALLATION

1. Take care of the polarity of new IC and then install the new IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily.

(Refer to Fig. 2-5.)

Soldering Iron

Solder temporarily

Fig. 2-5

2. Supply the solder from the upper position of IC leads sliding to the lower position of the IC leads.

(Refer to Fig. 2-6.)

4. When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thintip Soldering Iron.

(Refer to Fig. 2-8.)

Thin-tip Soldering Iron

Fig. 2-8

5. Finally, confirm the soldering status on four sides of the IC using a magnifying glass. Confirm that no abnormality is found on the soldering position and installation position of the parts around the IC. If some abnormality is found, correct by resoldering.

NOTE

When the IC leads are bent during soldering and/or repairing, do not repair the bending of leads. If the bending of leads are repaired, the pattern may be damaged. So, be always sure to replace the IC in this case.

Solder

Supply soldering from upper position to lower position

Soldering Iron

Fig. 2-6

3. Absorb the solder left on the lead using the Braided Shield Wire.

(Refer to Fig. 2-7.)

NOTE

Do not absorb the solder to excess.

Soldering Iron

Braided Shield Wire

Fig. 2-7

No. 52130

+ 13 hidden pages