JVC 5030057088 User Manual

LT-17S2 LT-23S2

WIDE LCD PANEL TV INSTRUCTIONS

5030057088

Thank you for buying this JVC WIDE LCD PANEL TV To make sure you understand how to use your new TV, please read this manual thoroughly before you begin. (“LCD” stands for Liquid Crystal Display.)

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.

WARNING

Always use the provided AC adapter and power cord.

WARNING

• Fingers may be trapped under the TV causing injuries. Hold the TV at the bottom in the middle, and do not allow it to tilt up or down.

• The TV may fall causing injuries. Hold the bottom of the stand with your hand and tilt the TV up and down.

• Do not allow children to hang from the TV, place their elbows on the TV or lean against the TV. Doing so may cause the TV to fall over and lead

to injuires.

CAUTION:

• To avoid electric shock or damage to the unit, first firmly insert the small end of the power cord into the AC Adpater unit it is no longer wobbly, and then plug the larger end of power cord into an AC outlet.

CAUTION:

• Operate only from the power source specified – 240 V, 50/60 Hz) on the AC adapter.

•

• Avoid damaging the AC plug, AC adapter and power cord.

(AC 100 • only

• When you are not using this unit for a long period of time, it is recommended that you disconnect the power cord from the main outlet.

CAUTION ON HEATING OF AC ADAPTER:

In using, the AC adapter get heat on the sunface of case.

• It is normal, not defective. while it is in operation.

• Don't be covered with any material on case of AC adapter

NOTES:

• The rating plate (serial number plate) and safety caution are on the back of the main unit.

• The rating information and safty causion of the AC Adapter are on its upper and lower sides.

Point defects

LCDs use collections of fine pixels to display images. While there is no problem with more than 99.99% of these pixels, please understand that a very small number of pixels may not light or may light all the time.

Distance recommendations

Avoid improper installation and never position the unit where good ventilation is impossible. When installing this TV, distance recommendations must be maintained between the set and the wall, as well as inside a tightly enclosed area or piece of furniture.

150 mm 150 mm

200 mm 200 mm

50 mm

Keep to the minimum distance guidelines shown for safe operation.

Failure to take the following precautions may cause damage to the television or remote control.

DO NOT block the TV’s ventilat ion opening s or holes.

(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.)

DO NOT place anything on top of the TV.

(such as cosmetics or medicines, flower vases, potted plants, cups, etc.)

DO NOT allow objects or liquid into the cabinet openings.

(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)

DO NOT place any naked flame sources, such as lighted candles, on the TV. DO NOT subject the TV to direct sunlight.

The surface of the TV screen is easily damaged. Be very careful with it when handling the TV. Should the TV screen become soiled, wipe it with a soft dry cloth. Never rub it forcefully. Never use any cleaner or detergent on it.

If there is a fault, unplug the unit and call a service technician. Do not attempt to repair it yourself or remove the rear cover and the

AC adapter.

Cleaning the screen

The screen is coated with a special thin film to reduce reflection. If this film is and other problems that can not be repaired may occur. Pay attention to the following when handling the screen.

• Do not use glue or adhesive tape on the screen.

• Do not write on the screen.

• Do not allow the screen to come in contact with any hard objects.

• Do not allow condensation to form on the screen.

• Do not use alcohol, thinner, benzene or other solvents on the screen.

• Do not rub the screen hard.

maged, uneven colors, discoloration, scratches,

CONTENTS

Setting up your TV..................................4

Installation..........................................................4

Using the stand ..................................................4

Putting the batteries into the Remote control .....5

Remove the terminal cover ................................5

Connecting the aerial and video cassette

recorder (VCR)...................................................6

Connecting the power cord to the AC outlet ......6

Initial settings .........................................7

TV buttons and functions ......................9

Turn the TV on from standby mode ...................9

Choose a TV channel ........................................9

Watch images from external devices .................9

Adjust the volume ..............................................9

Using the Menu..................................................9

Remote control buttons and

functions............................................10

Turn the TV on or off from standby mode........10

Choose a TV channel ......................................10

Adjust the volume ............................................11

Watch images from external equipment ..........11

Displaying the source information .....................11

ZOOM function.................................................12

Sleep timer funtion...........................................13

Picture mode....................................................13

Using the PCPIP

Operating a JVC brand VCR or DVD player ....14

function

...............................13

SOUND .................................................19

Sound Adjustment........................................... 19

HYPER SOUND

.............................................. 19

FEATURES............................................20

BLUE BACK.................................................... 20

CHILD LOCK................................................... 20

INSTALL................................................21

MANUAL.......................................................... 21

AUTO PROGRAM........................................... 21

To edit the PR LIST menu............................... 22

PC MENU...............................................25

PC PICTURE POSITION................................. 25

PC PICTURE................................................... 25

SOUND............................................................ 25

PC support mode list........................................ 26

Additional preparation.........................27

Connecting external equipment ...................... 27

Troubleshooting...................................29

Specifications.......................................31

Teletext function...................................15

Basic operation ................................................15

Hold..................................................................15

Sub-page .........................................................16

Reveal..............................................................16

Size ..................................................................16

Index ................................................................16

Cancel..............................................................16

Using the TV’s menu............................17

Basic operation ................................................17

Picture setting.......................................18

PICTURE MODE .............................................18

Picture Adjustment...........................................18

WHITE BALANCE..........................................18

RESET..............................................................18

Setting up your TV

Installation

Cautions for installation

• Install the TV in a corner on a wall or on the floor so as to keep cords out of the way.

• The TV will generate a slight amount of heat during operation. Ensure that sufficient space is available around the TV to allow satisfactory cooling. See “Distance recommendations” on page 2.

Using the stand

This TV comes with a Table Top Stand already attached.

This stand can be used to adjust the direction of the TV screen 5° up, 10° down, and 20° to the left or right.

Tilt the TV up and down:

While holding the bottom of the stand with one hand, use your other hand to hold the middle of the top of the TV and slowly tilt the TV up and down.

• As a safety measure, the stand is constructed so that it requires a certain amount of force to tilt the TV.

Rotate the TV to the left and right:

While holding the bottom of the stand with one hand, use your other hand to hold the edge of the panel and slowly adjust the direction of the TV screen.

Cable holder

A cable holder which is used to keep the connection cables tidy is attached to the back of the stand.

cable holder

Setting up your TV

Putting the batteries into the Remote control

Use two AA/R6 dry cell batteries. Insert the batteries from the - end, making sure the + and - polarities are correct.

• Follow the warnings printed on the batteries.

• Battery life is about six months to one year, depending on your frequency of use.

• The batteries we supply are only for setting up and testing your TV, please replace them as soon as you need to.

• If the remote control does not work properly, replace the batteries.

Remove the terminal cover

There are connection terminals behind the covers of the rear of the TV. Remove the cover before connecting a DVD or VCR. The covers can be removed by removing the hook at the top and then pulling out while lifting slightly. To replace the covers, first connect the hook at the bottom of the cover to the TV and then insert the hook at the top.

• Leave the covers off if they do not fit properly. Do not force to replace the covers. Doing so may cause damages of the connection cables and the covers.

• Leave these covers off when mounting the TV on a wall.

• 100mm mount based on VESA regulation is equipped.

• The handle and the stand can be left by loosing the screws with a screwdriver when mounting the TV on a wall.

• Spread a soft cloth on a flat table and then place the TV on the cloth with the screen facing downwards when you leave the

handle and the stand.

Setting up your TV

Connecting the aerial and video cassette recorder (VCR)

• Aerial cable is not supplied. Use a good quality 75-ohm coaxial cable.

• Read the manual that came with the VCR before connecting.

If not connecting a VCR (follow 11): Connect an aerial cable to the aerial socket on this TV.

If connecting a VCR: 1 Connect the aerial cable to the aerial input

socket on the VCR, and connect the VCR and TV with another aerial cable

2 Connect the VCR’s VIDEO OUT (video output)

terminal and the TV’s VIDEO terminal with a video cable

To connect a VCR to the TV with an S-VIDEO cable: Connect the VCR’s S-VIDEO OUT (S-VIDEO output) terminal and TV’s S-VIDEO terminal with an S-VIDEO cable A, instead of connecting with a video cable. Note that the connection with a video cable will be ignored in case you connect a VCR to the TV with both video cable and S-VIDEO cable.

3 Connect the VCR’s VIDEO OUT (audio L/R

output) terminals and the TV’s AUDIO input terminals with an audio cable

•

To connect additional external devices, please see “Connecting the external equipment” on page 27.

• If the VCR's audio output is in mono, connect the VCR's AUDIO OUT(audio output)terminal and the TV's audio L/MONO input terminal with an audio cable.

Connecting the power cord to the AC outlet

If you are connecting a AC adapter,

in the diagram below.

• Connect to the TV and to the AC outlet.

Caution

• Operate only from the power source spec – 240 V, 50/60 Hz) on the unit.

• Remove the AC plug from the outlet to completely disconnect the TV from the power supply.

DC IN (12V)

SUBWOOFER

AUDIO

PC IN

OUT

AUDIO

D-SUB

R L

15 PIN

ified (AC 100

VIDEO-1

S-VIDEO

VIDEO

L/MONO

AUDIO

COMPONENT

(VIDEO-2)

Pb/Cb

Pr/Cr

L/MONO

AUDIO

VIDEO-1

S-VIDOE VIDEO

VIDEO

L/MONO AUDIO

Pb/Cb

PR/CR

L/MONO AUDIO

DC IN

(12V)

SUBWOOFER

AUDIO

PC IN

OUT

AUDIO

D-SUB

R L

15 PIN

S-VIDEO

VIDEO

L/MONO

AUDIO

COMPONENT (VIDEO-2)

Pb/Cb

Pr/Cr

L/MONO

AUDIO

Initial settings

When the TV is first turned on, it enters the initial setting mode. Follow the

make the initial

instructions on the on-screen display to

settings.

VCR/TV/DVD Switch

Yellow button

Blue butOKton

BACK

___ ___

1 Make sure to set the VCR/TV/DVD switch to the

TV position.

• You cannot turn the TV on when the VCR/TV/DVD switch is set to the VCR or DVD position.

2 Press the button on the remote control

After a short interval the power lamp changes from red to green.

• Check that the AC plug on the power cord from the TV is connected to AC outlet.

Power lamp

3 AUTO PROGRAM menu appears.

INSTALL

LANGUAGE ENGLISH

AUTO PROGRAM

ress

SELECT

he buttons to choose the

:MOVE

LANGUAGE.

he buttons to choose the ENGLISH.

ress

The on-screen display will then be in English.

he buttons to choose the

ress

AUTO PROGRAM.

he buttons to enter the

ress

AUTO PROGRAM.

AUTO PROGRAM

START

OK : START

Press the OK button to start AUTO PROGRAM.

AUTO PROGRAM

NOW PROGRAMMING CH-01

MENU : EXIT

The AUTO PROGRAM menu appears and received TV channels are automatically stored in the programme numbers.

• To cancel the AUTO PROGRAM function: Press the MENU button.

After the TV channels have been registered in the programme numbers, the PR LIST menu appears

Remote control

sensor

PR LIST

01 ----02 ----03 ----04 ----05 ----06 ----07 ----08 ----09 ----10 -----

11 ----12 ----13 ----14 ----15 ----16 ----17 ----18 ----19 ----20 -----

21 ----22 ----23 ----24 ----25 ----26 ----27 ----28 ----29 ----30 -----

NIANME DELETE

• If you want, you can now edit the programme numbers using the AUTO PROGRAM function. For details, see “To edit the PR LIST menu” on page 22.

Initial settings

Now, the initial settings are complete, and you can watch the TV

•

If your TV can detect the TV channel name from the TV channel broadcast signal, the TV channel name is assigned to the programme number to which the TV channel has been set. However, which TV channels are set to which programme numbers will depend on the area in which you live.

• If a TV channel you want to view is not set to a programme number, you can set it using the MANUAL function. For details, see “To edit the

PR LIST menu" on page 22.

• The AUTO PROGRAM function does not set the programme number PR 0 for your video cassette recorder. You will need to set this using the MANUAL function.

• In some areas you may get TV reception from more than one transmitter, for example different ITV regions. In this case each TV channel could be set twice. If this happens, the first set of channels will have the stronger signal. If you want to delete the second set of channels, you will have to do it manually (see page 21).

TV buttons and functions

Press the button or P buttons to turn the TV on from standby mode

• Check that the AC plug on the power cord from the TV is connected to correctly AC outlet.

Choose a TV channel

Turn the TV on from standby mode

Press the P buttons to choose a programme number or an EXT terminal

Watch images from external devices

Press the TV/AV button to choose a TV/AV terminal

TV mode

Last program number

VIDEO-1

EXT modes

VIDEO-2

Adjust the volume

Power lamp

2 Remote control sensor 3

MENU button

TV/AV OK button

(Volume) button

P buttons

(Standby) botton

Headphone jack (mini jack)

Press the buttons

The volume level indicator appears.

Using the Menu

Use the MENU button.

Refer to "Using the TV's menu"(see page 17) for details of

using the menu.

+ 23 hidden pages