JVC 0307MNH-SW-BJ, CU-VD40U User Manual

CU-VD40U

DVD Burner

INSTRUCTIONS

Graveur de DVD

MANUEL D’UTILISATION

Grabador de DVD

MANUAL DE INSTRUCCIONES

ENGLISH

FRANÇAIS

ESPAÑOL

For Customer Use:

Enter the Model No. and Serial No. (located on the bottom of the burner) below. Retain this information for future reference.

Model No.

Serial No.

LYT1752-001A

This burner enables DVDs of videos recorded with the JVC Hard Disk Camera to be created without using a PC.

● If you want to edit videos recorded with the camera and create your original DVDs, use the software provided with the camera for editing and creating DVDs.

● The provided data writing software Power2Go 5.5 Lite can be used for writing data. However, it cannot be used to edit videos or create DVDs.

● The burner does not include support for Macintosh.

Caution on Replaceable lithium battery

The battery used in this device may present a fire or chemical burn hazard if mistreated. Do not recharge, disassemble, heat above 100% or incinerate. Replace battery with Panasonic (Matsushita Electric), Sanyo, Sony or Maxell CR2025. Danger of explosion or Risk of fire if the battery is incorrectly replaced.

● Dispose of used battery promptly.

● Keep away from children.

● Do not disassemble and do not dispose of in fire.

Dear Customer,

Thank you for purchasing this burner. Before use, please read the safety information and precautions contained in pages 2 and 3 to ensure safe use of this product.

Safety Precautions

IMPORTANT:

In the event that any of the following occur, remove the plug and make a request for repair to the dealer.

● Smoke or abnormal odor is emitted

● Damage from being dropped

● Water or an object enters inside

CAUTION:

A UNIT IS A CLASS 1 LASER PRODUCT. HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE UNIT CORRECTLY AS INSTRUCTED. WHEN THIS UNIT IS PLUGGED INTO THE WALL OUTLET, DO NOT PLACE YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY AND OTHER OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL. CLASS 1 LASER PRODUCT REPRODUCTION OF LABELS WARNING LABEL INSIDE OF THE UNIT

This unit applies to the standard “IEC60825-1:2001” for laser products.

The socket-outlet shall be installed near the equipment and shall be easily accessible.

ATTENTION:

This unit contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the unit off and unplug the mains power cord. Then plug it in again and turn the unit on. Take out the disc. After checking the disc, operate the unit as usual.

For USA-California Only

This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material – special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate

WARNING:

Batteries shall not be exposed to excessive heat such as direct sunshine, fire or the like.

Declaration of Conformity (for owners in the U.S.A.)

Model Number : CU-VD40U Trade Name : JVC Responsible party : JVC AMERICAS CORP. Address : 1700 Valley Road Wayne, N. J. 07470 Telephone Number : 973-317–5000 This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

(For owners in the U.S.A.)

Changes or modifications not approved by JVC could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help.

(For owners in Canada)

● FOR USE WITH MODEL NO. AP-V400U (AC ADAPTER).

● POUR UTILISER AVEC MODELE AP-V400U (ADAPTATEUR

CA). This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

The C/B button does not completely shut off mains power from the unit, but switches operating current on and off. ABB shows electrical power standby and ACB shows ON.

CAUTION:

To avoid electric shock or damage to the unit, first firmly insert the small end of the power cord into the AC Adapter until it is no longer wobbly, and then plug the larger end of the power cord into an AC outlet.

If malfunctioning occurs, stop using the unit immediately and consult your local JVC dealer.

Safety Precautions for the Burner

Be sure to observe the following precautions. Failing to do so may result in electric shock, fire, injury, or malfunction.

● Do not disassemble, dismantle, or modify the equipment. Requests for repair and inspection should be made to the dealer.

● Do not insert metal or combustible objects or pour water or other liquids inside the burner.

● Turn off the power when connecting equipment.

● Remove the plug when the burner will not be used for a

prolonged time or prior to cleaning (electricity flows through the equipment even when the power is off).

● Do not block the ventilation holes of the burner.

● Do not use where there is condensation. Suddenly carrying

the burner from a cold location to a hot location may result in the formation of drops, which may cause a malfunction or failure.

● Do not cause the burner to vibrate when discs are in.

Safety Precautions for Accessories

● When using the AC adapter, the power cord, and the USB cable, be sure to observe the following precautions. Failing to do so may result in electric shock, fire, injury, or malfunction.

• Do not insert or remove the plug when your hands are wet.

• Fully insert the plug into the outlet.

• Keep dust and metal objects away from the plug.

• Do not damage the cord.

• Place the cord where it will not trip someone up.

• Do not use when thunder can be heard.

• Do not dismantle.

• Do not use for any product other than this one.

● Do not play the provided CD-ROM with an audio player. Doing so may damage the circuits or speakers.

Safety Precautions for Discs

Do not use the following discs.

● Cracked discs

● Deeply scratched discs

Installation

Do not install in any of the following locations.

● Humid location

● Location of 60 °C or above

● Location subject to direct sunlight

● Location where overheating is likely

● Dusty or smoky locations

● Locations subject to oily smoke or steam such as a kitchen

counter or beside a humidifier

● Unstable location

● Bathroom

● Dusty places

● Slanted location

ATTENTION:

On placing the unit:

Some TVs or other appliances generate strong magnetic fields. Do not place such appliances on top of the unit as it may cause picture disturbance.

When moving the product:

Press C/B to turn off the power, and wait at least 30 seconds before unplugging the power cord. Then, wait at least 2 minutes before moving the product.

Cleaning Procedure

IMPORTANT:

● Be sure to unplug the burner before beginning cleaning.

● Do not use liquid or aerosol cleaners.

● Ensure that no moisture or liquid comes into contact with the

drive during cleaning.

Exterior of the Burner:

Wipe dirt off with a dr y cloth.

Disc Tray:

Wipe off dirt with a soft dry cloth.

Disc:

Gently wipe from the inner edge to the outer edge with a soft cloth.

Storage:

Make sure that discs are kept in their cases. If discs are piled on top of one another without their protective cases, they can be damaged. Do not put discs in a location where they may be exposed to direct sunlight, or in a place where the humidity or temperature is high. Avoid leaving discs in your car!

Region Codes

Region codes are numbers for restricting DVD video playback. The world is separated into six regions and each region is identified by a number. If the number for a disc does not match the number for the player, the disc cannot be played on the player. (The initial region code is indicated on the label on the bottom of the burner.)

Disclaimer

JVC accepts no liability whatsoever for loss of data resulting from inappropriate connections or handling.

Copyrights

Duplicating copyright protected material, for other than personal use, without the permission of the copyright holder is prohibited by copyright law.

Registered Trademarks and Trademarks

● Windows® is either registered trademark or trademark of Microsoft Corporation in the United States and/or other countries.

● Macintosh and Mac OS are trademarks of Apple Computer, Inc., registered in the United States and other countries.

● Pentium is a registered trademark of Intel Corporation in the United States.

● Manufactured under licence from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

● HDMI, HDMI logo and high definition multimedia interface are trademarks or registered trademarks of HDMI Licensing LCC.

● Other company and product names mentioned herein are registered trademarks and/or trademarks of their respective holders.

Enjoy High Definition Images Copied to DVDs!

Copying to DVD

A Connect.

Audio/Video cable

B Select the desired copy method.

The following 6 methods of copying are available.

Methods of copying Types of copy operation

Copy all (NORMAL BACK-UP)

Copy only favorite scenes (SELECT BACK-UP)

Copy all images shot.

Copy only newly shot images.

Search and copy by date.

Search and copy by scenes.

Search and copy by events.

(provided)

GZ-HD7U

instruction manual

0Page 48

0Page 49

z The date for videos created from playlists will be the same as the date the DVD is created.

C Copy to DVD.

z For details on finalizing, refer to

pages 48 to 50 of the GZ-HD7U instruction manual.

z Time taken for copying will be

long if there are a large number of files.

Select and set on “EXECUTE AND FINALIZE”.

z Additional recordings are not possible after finalizing.

To add new recordings

z Select and set on “EXECUTE” instead of “EXECUTE AND FINALIZE”. z Discs that are not finalized cannot be played back on PC or this burner.

To play back, connect as shown in the diagram above, and refer to pages 48 to 50 of the GZ-HD7U instruction manual.

Copy using playlists.

DVD35 DVD(DL)

EXECUTE

EXECUTE AND FINALIZE

CANCEL

SET TOP

SELECT

0Page 49

Viewing Images Copied to DVD on the TV

A Connect.

Audio/Video cable

(provided)

A Disconnect the USB cable and turn off this burner. B Connect the burner to the TV.

z To view high definition images, connect using an optional HDMI cable or component video cable.

B Play back.

A Turn on the burner.

z Confirm that the power lamp is lighted in orange. If the lamp is not lighted in orange, disconnect the USB cable then turn

off and on the power again.

Approx. 20 seconds later

B Press the open/close (M) button to eject the tray. C Insert a finalized disc. D Press the open/close (M) button to close the tray.

z The following screen appears.

PLAY IMAGEPLAY VIDEO

E Play back.

z For details on playback, refer to page 15 of this instruction manual.

Before erasing data from GZ-HD7U

.................................................................................................................................................................

z Confirm that the data has been copied to DVD before erasing.

DVD Burner

CU-VD40U

ENGLISH

Safety Precautions ..................................................................... 2

Enjoy High Definition Images Copied to DVDs! .........................4

Copying to DVD............................................................................................ 4

Viewing Images Copied to DVD on the TV ................................................... 5

Contents.....................................................................................6

Getting Started ........................................................................... 7

Accessories .................................................................................................. 7

Placing the Burner ........................................................................................ 7

Inserting a Disc............................................................................................. 7

Preparing the Remote Control ...................................................................... 7

Guide to Parts and Controls .......................................................8

Connecting to TV .......................................................................9

Connecting to a TV with HDMI Input Terminal ............................................. 9

Connecting to a TV with Component Video Input Connectors ..................... 9

Connecting to a TV with Video/Audio Input Connectors ............................ 10

Connecting to a TV with DVI Input Terminal............................................... 10

Saving Everio Camera Images to DVD....................................11

To Connect ................................................................................................. 11

Creating Data/DVD Video Discs................................................................. 11

Saving PC Images to DVD .......................................................12

To Connect ................................................................................................. 12

Saving to a DVD ......................................................................................... 12

Computers That Can Be Used ................................................................... 12

Installing CyberLink Power2Go 5.5 Lite ..................................................... 13

CyberLink Power2Go 5.5 Lite Contact Information .................................... 13

Folder Configuration................................................................. 14

Viewing Images Saved in DVD ................................................15

Viewing Videos Saved from High Definition Everio Camera ...................... 15

Viewing Still Images Saved from High Definition Everio Camera ............... 17

Viewing DVD Videos Saved from Everio Camera....................................... 18

Viewing High Quality Images ................................................... 19

Changing the Settings ..............................................................20

Menu Operation Procedures ...................................................................... 20

Setting Items And Contents........................................................................ 21

Screen Display ......................................................................... 22

Troubleshooting .......................................................................23

Error Messages ........................................................................24

Specifications ........................................................................... 25

Getting Started

Accessories

Power cord AC adapter

Remote control

(RM-V41U)

CAUTION:

z Do not use the provided AC adapter and power cord with other devices. In addition, do not use AC adapter, power cord and

USB cable other than those provided with this burner. Doing so may result in electric shock or fire.

USB cable

DVD-ROM Lithium Battery (CR2025)

Audio/Video

cable

Recording disc (DVD-R DL)

(For use with high definition Everio Camera.

Cannot be used with an Everio Camera.)

(AP-V400U)

Stand

Pre-installed in the remote

control unit.

Placing the Burner

 Horizontal orientation

z Take note of the top and bottom of the burner and

place it in the horizontal orientation.

 Vertical orientation

z When using in the vertical orientation, align the vent of

the burner with that of the provided stand, then place and fix the burner securely on the stand.

Bottom surface

Stand (provided)

Vent

Inserting a Disc

When handling a disc, be sure not to touch the playback/recording side of the disc. Use only the [M] button on the burner or the remote control to eject the disc tray. If you open the tray manually,

there is a risk of the disc dropping out or getting caught.

 Vertical orientation Horizontal orientation

Preparing the Remote Control

A battery is included inside the remote control at the time of purchase. Remove the insulation sheet before use.

 To Reinsert the Battery

z Pull out the battery holder by pressing the lock tab.

Lock Tab

Lithium Battery (CR2025)

Guide to Parts and Controls

Front

.................................................................................................................................................................

Rear

.................................................................................................................................................................

CD E F G

COMPONENTVIDEO OUT

R PB Y

LVIDEO

AUDIO

A Open/Close Button (M) B Power Button (C/B) C Power Lamp

Green light:

When connected to Everio camera or PC.

Orange light:

During playback.

D Play/Pause Button (I/W) E Stop Button (o) F Previous Button (S) G Next Button (T) H Disc Tray

A DC Connector B USB Connector C Cooling Fan D HDMI Terminal E COMPONENT VIDEO OUT Connectors F AUDIO output Connectors G VIDEO output Connector

Remote control

.................................................................................................................................................................

A B C

E F

G H

J K

O P

Q R

A OPEN/CLOSE Button (M) B SET UP Button C TOP MENU Button D Selection keys ( / / / ) E STOP Button (o) F PREVIOUS Button (S) G REV Button (O) H FWD Button (N) I PLAY/PAUSE Button (I/W) J TOOL Button K RESOLUTION Button L ON SCREEN Button M MENU Button N ENTER Button O RETURN Button P Skip Button (v) Q Replay Button ( R NEXT Button (T)

Connecting to TV

To view high definition images, connect using an optional HDMI cable or component video cable.

Connecting to a TV with HDMI Input Terminal

 TV

 This burner

COMPONENTVIDEO OUT

R PB Y

NOTES:

z Images can only be displayed on a High-bandwidth Digital Content Protection (HPCP) monitor. (0P24) z When images do not appear normally, set the “HDMI COLOR SETTING” in the setting menu to “RGB”. (0P21)

L VIDEO

AUDIO

HDMI

HDMI cable (not provided)

Connecting to a TV with Component Video Input Connectors

 TV

Component video cable

(not provided)

 This burner

COMPONENTVIDEO OUT

R PB Y

Component video cable

Y=Green / P

R=Red

B=Blue

Audio cable

L=White / R=Red

L VIDEO

AUDIO

Audio cable (not provided)

AUDIO IN

LYCB/PBCR/PR R

+ 19 hidden pages