jurop PNR 104, PNR 124, PNE 104, PNE 124, PNR 142SL Instructions For Installation, Use And Maintenance Manual

I

I

NNSSTTAALLLLAATTIIOON

N

,

,

UUSSEE AANNDD

MMAAIINNTTEENNAANNCCEE MMAANNUUAAL

L

EN

PNR/PNE

104

-

124

-

PNR

142SL

Rev. 0

1

19-07-2016

O

O

RRIIGGIINNAALL

I

I

NNSSTTRRUUCCTTIIOONNS

S

REV. 0

1

19-07-2016

I

NSTALLATION, USE AND MAINTENANCE MANUAL –

PNR/PNR 104-124 – PNR 142

2 / 32

Jurop

SpA

Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)

TEL. +39 0

434 636811

FAX.

+39 0

434 636812

http://www.jurop.it

e-mail: [e-mail]

2016

– Jurop

–

Azzano Decimo (PN)

Reproduction, electronic storage and dissemination, even partial, are prohibited.
Jurop reserves the right to modify the products described in this manual without prior notice.
Any product names mentioned herein are the trademarks of their respective owners.

REV. 01

19-07-2016

I

NSTALLATION, USE AND MAINTENANCE MANUAL –

PNR/PNE 104-124 – PNR 142

3 / 32

Jurop

SpA

Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)

TEL. +39 0

434 636811

FAX.

+39 0

434 636812

http://www.jurop.it

e-mail: [e-mail]

Contents

1. General warnings

pag. 4

1.1 Introduction 4

1.2 Spare part request 4

1.3 Warranty terms and conditions 4

2. Technical data

pag. 5

2.1 Dimensions and arrangements 6

2.2 Performances 8

2.3 Usage limitations 8

2.4 Sound pressure level 9

2.5 Lubrication 9

3. Safety and accident prevention

pag. 10

3.1 General recommendations 10

3.2 Intended use 10

4. Installation

pag. 10

4.1 Checking upon receipt 11

4.2 Storing in the warehouse 11

4.3 Mounting 11

4.4 Vacuum – Pressure Line 11

4.5 Hydraulic actuator adjustment 12

4.6 Pneumatic actuator adjustment 12

4.7 Pump mounting – Drive connection 12

5. Start up

pag. 14

5.1 Pump starting-up 14

5.2 Precautions when starting the system 14

6. Maintenance

pag. 15

6.1 Ordinary maintenance 15

6.2 Extraordinary maintenance 16

7.

Malfunctions:
troubleshooting

pag. 19

8. Scarapping

pag. 19

S

PARE PART DATA SHEET –

PNR/PNE 102-124 D 20

S

PARE PART DATA SHEET –

PNR/PNE 102-124

MULTIPLIER

22

S

PARE PART DATA SHEET –

PNR 142 D 24

S

PARE PART DATA SHEET –

PNR 142

MULTIPLIER

26

S

PARE PART DATA SHEET –

PNR/PNE 102-124

HDR E ACCESS

. 28

S

PARE PART DATA SHEET –

PNR 142

HDR E ACCESSORIES

29

REV. 0

1

19-07-2016

I

NSTALLATION, USE AND MAINTENANCE MANUAL –

PNR/PNR 104-124 – PNR 142

4 / 32

Jurop

SpA

Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)

TEL. +39 0

434 636811

FAX.

+39 0

434 636812

http://www.jurop.it

e-mail: [e-mail]





















1.1. Introduction

• This booklet contains the necessary instructions for a correct
installation, running, use and maintenance of the pump, as well as
some practical suggestions for a safe operating.

• The knowledge of the following pages will grant a long and
trouble-free operation of the pump.

• Following the instructions below contributes to limiting pump repair
expenses by extending its duration, as well as preventing hazardous
situations, thereby increasing its reliability.

• If the pump is driven by an hydraulic motor please refer to
manufacturer's specific manual.

• It is recommended to:

- Read, understand and apply carefully the instructions before
running the pump.

- Keep the booklet at hand and have it known to all operators.

• Below is a brief description of the symbols used in this manual.

If these safety rules are not respected, operators can
be injured and the pump or oilers damaged
remarkably.

If these safety rules are not respected, the pump or
system can be damaged.

Suggestions for an environment friendly use of the
pump.

Useful information for an easy usage and
maintenance of the pump.

• The graphic representations and photographs contained in this
manual are there to illustrate the product in the parts that make it up
and in specific operating phases. Though the model shown in the
manual may differ from the one purchased, the operating principle at
the base of the illustrated operating phase is the same.

• Every PNR/PNE pump has to be fitted with its own tag reporting
the following data: Model, Serial number, Year, Max speed, Max
pressure.

Pic. 1.1

1.2. Spare part request

• Use only genuine spare parts for maintenance and repairs. To

order spare parts, provide the following details:

EXAMPLE:

a) The model of the pump (see pump tag) PNR 104

b) The serial number of the pump (see pump tag) K60001

c) A description of the parts (see parts list)

VANE

d) The quantity (see parts list) n°5 pcs

e) The code number of the part (see parts list)

16016 059 00

1.3. Warranty terms and conditions

• Compliance with the installation, use and maintenance instructions

provided by this manual is crucial for the recognition of warranty
against defective parts.

1.

General warnings

REV. 01

19-07-2016

I

NSTALLATION, USE AND MAINTENANCE MANUAL –

PNR/PNE 104-124 – PNR 142

5 / 32

Jurop

SpA

Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)

TEL. +39 0

434 636811

FAX.

+39 0

434 636812

http://www.jurop.it

e-mail: [e-mail]

• Sliding vanes vacuum pump injection cooled (PNR) or natural air-cooling (PNE). The PNR version is meant for heavy duty; the PNE version for
normal use.

• Forced oil lubrication of both bearings and sealings. Copper oil piping. Rear oil tank (PNE/PNR 104-124). Side oil tank (PNR142).

• Manifold with non-return valve on the pump inlet.

• Built-in vacuum-pressure changeover valve. Pneumatic or hydraulic actuator are available.

• Transmission:

- Direct with smooth or splined shaft.

- Gearbox transmission (ASAE 1” 3/8) 540 or 1000 rpm, counter clockwise rotation.

- Hydraulic motor.

STANDARD EQUIPMENT

• Sliding-vanes, air cooled vacuum pump.

• Asbestos-free tangential vanes.

• Automatic lubrication by means of a volumetric pump and an oil

tank.

• Asymmetrical manifold with check valve installed on the pump

inlet.

• Pivoting suction and exhaust conveyors in aluminum alloy.

• Direct transmission with smooth or splined shaft (ASAE 1 3/8”).

• Gearbox transmission with smooth or splined shaft.

• Counter clockwise rotation.

• Injection cooled (PNR) or natural air-cooling (PNE).

AVAILABLE ON REQUEST

• Clockwise rotation.

• Transmission with hydraulic motor.

• Drive by means of mechanical drive from Power Take Off.

• Pulley for the belt drive.

• Pneumatic actuator for the vacuum/pressure changeover valve.

• Hydraulic actuator for the vacuum/pressure changeover valve.

PPNNR

R

/

/

PPNNEE

2.

Technical data

AIR INJECTION VALVES

(

PNR

)

MANIFOLD WITH NON-RETURN VALVE ON THE PUMP INLET

EUROPEAN PATENT APPL

ICATION

PUMP HOUSING

GEARBOX

OIL TANK

OIL FILLING PORT AND

DIP STICK

VACUUM/PRESSURE

CHANGEOVER VALVE

CONVEYOR

SUCTION/EXHAUST

AUTOMATIC

LUBRICATING PUMP

SIDE OIL TANK

VANES INSPECTION

PORT

DRIP OILERS

VACUUM/PRESSURE

CHANGEOVER VALVE

REV. 0

1

19-07-2016

I

NSTALLATION, USE AND MAINTENANCE MANUAL –

PNR/PNR 104-124 – PNR 142

6 / 32

Jurop

SpA

Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)

TEL. +39 0

434 636811

FAX.

+39 0

434 636812

http://www.jurop.it

e-mail: [e-mail]

2.1 Dimensions and arrangements

WEIGHT PNR/PNE 104 PNR/PNE 124 PNR 142 SL

Direct transmission (smooth or splined shaft) 150 Kg 177 Kg 210 Kg

Gearbox transmission (540 rpm) 173 Kg 190 Kg 225 Kg

Gearbox transmission (1000 rpm) 173 Kg 190 Kg 230 Kg

Hydraulic motor 180 Kg 210 Kg 224 Kg

PNR/PNE 104-124 Direct transmission

Mod. A B B1 C D D1 E E1 F F1 G H I L M N O P Q R S

PNR104 321 329 313 153 253 238 320 320 83 67 67 16,5 368 285 249 534 367 167,5 40 43 12

PNR124 353,5 362 346 153 285 269 352 352 83 67 67 16,5 368 285 249 534 367 167,5 40 43 12

PNR/PNE 104-124 Gearbox transmission

Mod. A A1 B C D E F G H I L M N O P Q

PNR104 727 791 406 153 329 85,5 67 16,5 368 285 249 600 534 367 50 62

PNR124 792 856 437 153 368 85,5 67 16,5 368 285 249 600 534 367 50 62

REV. 01

19-07-2016

I

NSTALLATION, USE AND MAINTENANCE MANUAL –

PNR/PNE 104-124 – PNR 142

7 / 32

Jurop

SpA

Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)

TEL. +39 0

434 636811

FAX.

+39 0

434 636812

http://www.jurop.it

e-mail: [e-mail]

PNR/PNE 104-124 Hydraulic motor

Mod. A B C D E F G H I L M N O P1 P2

PNR104 907 586 153 510 67 16,5 136 258 368 285 249 534 367 1” ½ 1” ¼

PNR124 955 502 153 525 67 16,5 144 258 368 285 249 534 367 - -

PNR 142 Side oil tank

PNR142 M (540-1000

RPM

) PNR142 D PNR142 HDR

REV. 0

1

19-07-2016

I

NSTALLATION, USE AND MAINTENANCE MANUAL –

PNR/PNR 104-124 – PNR 142

8 / 32

Jurop

SpA

Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)

TEL. +39 0

434 636811

FAX.

+39 0

434 636812

http://www.jurop.it

e-mail: [e-mail]

2.2 Performances

Performances PNR/PNE 104 D PNR/PNE 104 M PNR/PNE 104 HDR

Maximum speed 1300 rpm 540 - 1000 rpm 1300 rpm

Air flow at free air condition 10400 l/min - 624 m³/h 10400 l/min - 624 m³/h 10400 l/min - 624 m³/h

Air flow at 60% vacuum rate 9400 l/min - 564 m³/h 9400 l/min - 564 m³/h 9400 l/min - 564 m³/h

Maximum vacuum 95 % 95 % 95 %

Maximum vacuum at continuos duty PNR 70 % 70 % 70 %

Maximum vacuum at continuos duty PNE 60 % 60 % 60 %

Power required at 0,5 bar rel (1,5 bar abs) 14 kW 14 kW 14 kW

Max operating rel. pressure (abs.) at continuos duty 1 bar (2 bar abs) 1 bar (2 bar abs) 1 bar (2 bar abs)

Max operating rel. pressure 2,5 bar abs 2,5 bar abs 2,5 bar abs

Oil consumption 130-150 g/h 130-150 g/h 130-150 g/h

Oil tank capacity 3,2 l 3,2 l 3,2 l

Performances PNR/PNE 124 D PNR/PNE 124 M PNR/PNE 124 HDR

Maximum speed 1300 rpm 540 - 1000 rpm 1300 rpm

Air flow at free air condition 12400 l/min - 744 m³/h 12400 l/min - 744 m³/h 12400 l/min - 744 m³/h

Air flow at 60% vacuum rate 11200 l/min - 672 m³/h 11200 l/min - 672 m³/h 11200 l/min - 672 m³/h

Maximum vacuum 95 % 95 % 95 %

Maximum vacuum at continuos duty PNR 70 % 70 % 70 %

Maximum vacuum at continuos duty PNE 60 % 60 % 60 %

Power required at 0,5 bar rel (1,5 bar abs) 16 kW 16 kW 16 kW

Max operating rel. pressure (abs.) at continuos duty 1 bar (2 bar abs) 1 bar (2 bar abs) 1 bar (2 bar abs)

Max operating rel. pressure 2,5 bar abs 2,5 bar abs 2,5 bar abs

Oil consumption 130-150 g/h 130-150 g/h 130-150 g/h

Oil tank capacity 3,2 l 3,2 l 3,2 l

Performances PNR142 D PNR142 M (540rpm) PNR142 M (1000rpm) PNR142 HDR

Maximum speed 1200 rpm 540 rpm 1000 rpm 1200 rpm

Air flow at free air condition 14200 l/min - 852 m³/h 14200 l/min - 852 m³/h 14200 l/min - 852 m³/h 14200 l/min - 852 m³/h

Air flow at 60% vacuum rate 12800 l/min - 768 m³/h 12800 l/min - 768 m³/h 12800 l/min - 768 m³/h 12800 l/min - 768 m³/h

Maximum vacuum 95 % 95 % 95 % 95 %

Maximum vacuum at continuos duty 70 % 70 % 70 % 70 %

Power required at 0,5 bar rel (1,5 bar abs) 20,5 kW 20,5 kW 20,5 kW 20,5 kW

Max operating rel. pressure (abs.) at continuos duty 1 bar (2 bar abs) 1 bar (2 bar abs) 1 bar (2 bar abs) 1 bar (2 bar abs)

Max operating rel. pressure 1,5 bar (2,5 bar abs) 1,5 bar (2,5 bar abs) 1,5 bar (2,5 bar abs) 1,5 bar (2,5 bar abs)

Oil consumption 160-170 g/h 160-170 g/h 160-170 g/h 160-170 g/h

Oil tank capacity 4 l 4 l 4 l 4 l

REFERENCE CONDITIONS

Conveyed gas: air Vacuum condition: atmospheric discharge

Ambient reference temperature: 20°C (68°F) Pressure condition: atmospheric suction

Absolute reference pressure: 1013mbar (14.7psi) Actual performance may vary of ± 5%

2.3 Usage limitations

Model

Max. Speed (rpm)

P (bar ABS)

T (°C)

Room Temperature

Direct - HDR Mult - 540 Mult - 1000 PNR PNE

PNR / PNE 104 850 - 1300 360 - 540 650 - 1000 2,5 bar abs 180 °C 160 °C -20 / +40°C

PNR / PNE 124 850 - 1300 360 - 540 650 - 1000 2,5 bar abs 180 °C 160 °C -20 / +40°C

PNR 142 850 - 1300 360 - 540 650 - 1000 2,5 bar abs 180 °C 160 °C -20 / +40°C

P: absolute pressure during delivery T: temperature during delivery

REV. 01

19-07-2016

I

NSTALLATION, USE AND MAINTENANCE MANUAL –

PNR/PNE 104-124 – PNR 142

9 / 32

Jurop

SpA

Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)

TEL. +39 0

434 636811

FAX.

+39 0

434 636812

http://www.jurop.it

e-mail: [e-mail]

2.4 Sound pressure level

Sound pressure level PNR104 PNE104 PNR124 PNE124 PNR142sl

60% vacuum rate, distance of 7 meter dB (A) 78 75 78 75 78

2.5 Lubrication

Recommended oils and greases: OIL TANK

Room T Viscosity Type ENI ESSO SHELL TOTAL MOBIL BP

TEXACO

HAVOLINE

< 10°C ISO VG 46 Mineral Oil Acer 46 Nuto 46 Morlina oil 46 Drosera MS 46 Nuto H 46 Bartran HV 46 Rando HD 46

> 10°C ISO VG 150 Mineral Oil Acer 150 Nuto 150 Morlina oil 150 Drosera MS 150 Nuto H 150 Bartran HV 150 Rando HD 150

Recommended oils and greases: GEARBOX

Viscosity Type ENI ESSO SHELL TOTAL MOBIL BP

TEXACO

HAVOLINE

ISO VG 220 Mineral Oil Blasia 220 Spartan EP 220 Omala oil 220 Carter EP 220 Mobilgear 630 Energol GR XP 220 Meropa 220

REV. 0

1

19-07-2016

I

NSTALLATION, USE AND MAINTENANCE MANUAL –

PNR/PNR 104-124 – PNR 142

10 / 32

Jurop

SpA

Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)

TEL. +39 0

434 636811

FAX.

+39 0

434 636812

http://www.jurop.it

e-mail: [e-mail]

Attention: carefully apply these prescriptions.

3.1 General recommendations

• Installation and maintenance must be carried out with the unit
totally disengaged from its drive system and must be performed by
qualified personnel.

• Use adequate clothing (avoid ties, loose sleeves, necklaces and so
on) and suitable protection equipment (gloves, protection glasses,
boots...).

• To prevent errors and hazardous situations, establish what each
operator is responsible for in the different maintenance operations.

• Durante il trasporto del decompressore utilizzare adeguate
imbracature. Appoggiare il decompressore su punti stabili.

• When transporting the compressor use proper slinging. Store the
compressor in stable places.

• Before each maintenance operation, stop the pump and restore
the atmospheric pressure.

• Make sure that all the parts of the unit are idle and cool, before
performing any maintenance operation.

• When the pump is running, some parts may reach very high
temperatures (above 100°C). Use all necessary precautions to avoid
contact.

• Operators working nearby must avoid prolonged exposure to the
noise emitted by the aspirator, if not equipped with the proper ear­protection devices.

• Avoid accidental suction of solids: solids may be projected at high
speed through the exhaust manifold and cause injures. A filter must be
mounted on the sunction line (Mesh 55).

• Do not start the machine if the protection devices provided for

transmissions are removed. Replace damaged part.

• Pressure relief valve: point the air flux away from the operators.

• Do not use the aspirator over its designed limits: the machine may

be damage and the operator may be injured.

Do not exceed the speed and the power supply
parameters indicated in the technical tables (see
par. 2.2 - 2.3).

3.2 Intended use

• Vacuum pumps of the PNR/PNE series are commonly used on
stationary or mobile equipment for suction and transfer by means of
vacuum or socalled pneumatic-transportation of liquid and solid wastes.

• They are air-cooled and consequentely foreseen for a non­continuous duty. The mod. PNE and the mod. PNR, the latter supplied
with air injection system (fig. 1) and meant for heavy duty works, do not
accept operating temperatures over 150 °C (300 °F), checked at not
more than 150 mm from the discharge connections.

• Evitare l’aspirazione di materiali tossici e di gas infiammabili o
esplosivi poiché i componenti interni possono raggiungere temperature
elevate.

• Avoid suction of liquids or solids, they can seriously damage the
pump.

• Do not run the pump over its designed operating limits (see par.

2.3): it may break and transmission can be damaged.

Main components legend

1. Vacuum/Pressure change-over valve

2. Air injection valves (PNR)

3. Oil tank

4. Vanes inspection port

5. Gear box oil filling plug

6. Gear box oil level plug

7. Drip oilers

8. Oil filling port and dip stick

9. Exhaust conveyor

10. Suction conveyor

11. Pressure relief valve port.

Available only if foreseen with additional conveyor
Code1627102500.

12. Non-returne valve (Intake manifold)

Pic. 4.1

4. Installation

3.

Safety and accident prevention

x

y

PNR/PNE 104-124

PNR 142 SL

REV. 01

19-07-2016

I

NSTALLATION, USE AND MAINTENANCE MANUAL –

PNR/PNE 104-124 – PNR 142

11 / 32

Jurop

SpA

Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)

TEL. +39 0

434 636811

FAX.

+39 0

434 636812

http://www.jurop.it

e-mail: [e-mail]

4.1. Checking upon receipt

• When the goods are delivered, make sure that all parts listed on
the delivery note are in perfect condition and have suffered no damage
during shipping.

• Make sure the vacuum pump has its identification plate. Pumps
without such identification are to be considered anonymous and
potentially dangerous: in such an event, they must not be used,
otherwise the manufacturer will be deemed free from any liability
whatsoever.

• Pump must be kept in a dry storage area. During storage, inlet and
outlet ports must be kept closed.

4.2. Storing in the warehouse

• If the compressor will not be installed inside a short time after
delivery:

- Remove the guards from the ports and spray a film of
protective oil over the inner surfaces of the body, rotors and
sides. Then attach again the guards;

- Store in a closed and dry place. Renew the preserving oil
periodically.

• To temporarily store a used pump, follow the instructions below:

- Thoroughly clean the pump.

- Equip the pump with suitable anti-corrosion protection.

4.3. Mounting

• The pump must be assembled for an easy access for maintenance
operations and secured rigidly to a frame or levelled base (max. 3°
slant to the horizontal plane. See Fig. 4.1). The base must be such as
to avoid vibrations, bending or deformation.

• Leave enough space around the pump to allow the free circulation
of air for cooling; avoid exposure to dirt and debris.

• Provide the necessary space to reach all points of lubrication
control (oil level), and the oil tank filler cap, the lever of the 4-way
switch, vanes inspection ports. See Pic. 4.1.

• For PNR/PNE 104-124 the oil tank is mounted on the rear side of
the pump. Instead for PNR142 the oil tank is mounted on the suction
side of the housing.

• In case of PNR/PNE with hydraulic motor, provide the necessary
space to disassemble the motor itself and proceed with joint lubrication.

4.4. Vacuum / Pressure line

• See picture 4.2.

Pic. 4.2

• The hoses connecting the suction and exhaust ports of the vacuum
pump must be of adeguate diameter (suggested not less than 3”) and of
oil and corrosion resistant materials and before connecting them, make
sure that they are perfectly clean in the inside.

• The weight or dimensions of the pipes must in no way stress the
PNR/PNE body. Use high temperature resistant rubber sleeves.

• Remove the port guards when mounting. The pipes and
components of the whole line must be clean.

• Avoid constrictions and tight curves where they are not essential.

• Connect the pump to the tank through the suction manifold (Fig.

4.1 - pos. 10) which has a threaded port for fitting the over-pressure
valve.

• The exhaust pipes can reach high temperatures. Protect those
adequately from the operator reach.

• A clapet valve on suction pipe avoids rotation in the opposite
direction when the pump stops.

• To avoid that foreign liquids will enter the vacuum pump it is
necessary to mount on the suction line an over-flow valve of “floating­ball” type (Fig. 4.2. - pos. 1). The flow section of this valve must be
equivalent to the suction hose’s one.

• It is also necessary to have on the line a suitable air filter for
preventing solids to be sucked inside the vacuum pump. It is also
recommended to mount a “secondary shutoff” of floating-ball type (Fig.

4.2 - pos. 2) between vacuum pump and over-flow (primary shutoff),
along with the previously mentioned air filter (Fig. 4.2 - pos. 3).

• Called also 4-way valve, normally is manually operated but it can
be at any time transformed in pneumatically or hydraulic operated upon
request of the appropriate kit.

• During normal running of the pump the resulting noise should be
reduced by means of a suitable silencer (Fig. 4.2 - pos. 4) mounted as
close as possible to the pump itself. It has to be dimensioned for the air
flow produced by the pump model. The oil used for the pump’s inside
lubrication has to be separated from the exhausted air by means of an
adequate oil-separator, placed directly inside the silencer.

Vacuum / Pressure line components

1

Primary shutoff

2

Secondary shutoff

3

Suction filter

4 Silencer

5

Over-pressure safety relief valve

6

Vacuum control valve

45 6

123

REV. 0

1

19-07-2016

I

NSTALLATION, USE AND MAINTENANCE MANUAL –

PNR/PNR 104-124 – PNR 142

12 / 32

Jurop

SpA

Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)

TEL. +39 0

434 636811

FAX.

+39 0

434 636812

http://www.jurop.it

e-mail: [e-mail]

The silencer is fitted also with a draining tap for the collected oil and

condensed liquids.

• Over-pressure safety relief valve (Pic. 4.2 - pos. 5). It must be
dimensioned to discharge the entire air-flow of the pump. The
adjustement of this valve has to be kept inside 10% of tollerance of the
pump's working pressure and in any case it has to stay inside the given
value of the tank's work pressure.

• Vacuum control valve has to be fitted on the suction piping, if the
tank's characteristics or the vacuum line will need this kind of vacuum­limiting device.

Pic. 4.3

• For pumps that reach, during normal operating, discharge air
temperature close to 150 °C (300°F) - (checked at not more than 150
mm from the discharge connection) it is necessary to use a device
(overheating limiter) that will not allow to exceed such temperature.
Contact our Technical Department.

• An adjustable curved pipe is installed on the outlet of the silencer,
in order to prevent rain from entering and to enable positioning (during
installation) of the output airflow.

• Direct the silencer discharge output away from the silencer suction
inlet in order to prevent the input of hot fluids into the injection inlet.

Attention: direct the silencer discharge output
away from the silencer suction inlet.

4.5 Hydraulic actuator adjustment

• Extraordinary maintenance operations can require the upper cover
(and that of the actuator, either manual or pneumatic) to be removed.
We recommend ensuring enough space to carry out such operations.

• If the cock blocks or it moves with friction, screw up the clearance
regulation nut (A). Screw up ¼ of turn each time. Block the nut rotation
with the safety nut.

• The lubrication points (B) and the clearance regulation bolt (A)
must be accessible. See Fig. 4.5.

• Lubricate with grease every 1000 cycles. Grease type NLGI 2.

• It is suggested to install 2 one‐way flow controller between the
hydraulic switch and the hydraulic actuator. Set the flow controllers in
order to prevent hard hitting through the end of stroke. Minimum
commutation time: 1 second.

• Maximum feed pressure: 30 bar.

• To order spare parts see spare parts list at the end of this manual.

Pic. 4.4

4.6 Pneumatic actuator adjustment

• In the event of 4-way valves equipped with pneumatic actuator, we
recommend installing two one-way flow regulators between the
pneumatic “control” and the pneumatic actuator. The following figure
shows a schematic view of a possible pneumatic installation.

Pic. 4.5

• We recommend adjusting the two flow regulators in order for
rotation to occur without knocks and with a switching time of at least
one second.

4.7. Pump mounting - drive connection

A) Cardan shaft drive

• Use telescopic cardan shafts.

• In order to achieve a uniform motion of the driven shaft, the
following requirements must be met (see Pic. 4.6):

- Equal working angle α and α1 of both couplings;

- The internal fork joints must be coplanar;

- Both driven and driving shafts must be coplanar.

• It is also recommended working with limited articulated joint angles
(max 15° at 1000 rpm and max 11° at 1100 rpm) and disengaging the
transmission for those operations requiring great angles (steering or
lifting).

VACUUM CONTROL VALVE

SET UP

REV. 01

19-07-2016

I

NSTALLATION, USE AND MAINTENANCE MANUAL –

PNR/PNE 104-124 – PNR 142

13 / 32

Jurop

SpA

Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)

TEL. +39 0

434 636811

FAX.

+39 0

434 636812

http://www.jurop.it

e-mail: [e-mail]

α

α

1

α

α

1

DRAINING

PORT

Pic. 4.6

Follow the rotation direction as indicated on the
pump front conveyor protection. Follow the
instructions of the cardan shaft’s manufacture.

• Use the protection that comes with the Julia group shaft.

Use the cardan protection supplied with the
pump. The pump installation must fulfill the
current EC injury prevention specifications.

B) Belt drive

Pic. 4.7

• Install a suitable pulley on the smooth shaft as close as possible
to the pump in order to avoid excessive bending stress on the drive
shaft.

• Apply an adequate belt tension (see list below).

• Do not use driven or driving pulleys with a pitch diameter inferior
to values reported in the box below. Small pulleys require a high belt
tension which may cause premature wear to the bearing or
transmission damages.

Model Max. Speed (rpm) T. max (N) L. max (mm) Pitch diameter (mm) Nr. Grooves Belts type

PNR/PNE104 1300 3300 35 200 2 XPB

PNR/PNE124 1300 3300 35 200 2 XPB

PNR 142 (1 bar abs) 1300 3300 35 200 3 XPB

Pitch Diameter. min.: Minimum drive of pulley pitch diameter.

C) Hydraulic drive transmission (PNR/PNE HDR)

Model Displacement

Operating pressure

(max. vac.)

Operating pressure

(1 rel. bar)

Flow

Max pressure

draining line

Max. pressure
motor exhaust

Max pressure

PNR/PNE104 61 cc/rev 130 bar 170 bar 83 l/min (1300rpm) 5 bar 5 bar 180 bar

PNR/PNE124 72 cc/rev 130 bar 170 bar 98 l/min (1300rpm) 5 bar 5 bar 220 bar

PNR 142 86 cc/rev 150 bar 200 bar 110 l/min (1200rpm) 5 bar 5 bar 220 bar

(*) : Oil temperature, used in the main circuit.

• Fluid: mineral oil for hydraulic systems in compliance with ISO/DIN.

Temperature Optimum viscosity ale Max. viscosity allowed

-20 / +80 °C 12 – 100 cSt 750 cSt

• Filtration: class 21/19/16 contamination according to ISO 4406 to

be obtained with a ßx = 75 filter.

• Check circuit connections: they must be applied in the same

rotation direction as that indicated by the arrow on the pump front
flange.

• Draining: connect directly to the tank above the maximum oil

level. Operating without draining line may damage the motor.

Pic. 4.8

DP MIN

KEEP AXELS PARALLEL

ALINGN PULLEY GROVES AND BELTS

CHECK BELT TENSION

T

MAX

REV. 0

1

19-07-2016

I

NSTALLATION, USE AND MAINTENANCE MANUAL –

PNR/PNR 104-124 – PNR 142

14 / 32

Jurop

SpA

Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)

TEL. +39 0

434 636811

FAX.

+39 0

434 636812

http://www.jurop.it

e-mail: [e-mail]

• Distributor: open-centre distributor in central idle position

(vacuum pump off). It must be equipped with an adjustable
overpressure safety valve.

• Motor pipeline: outlet pipe must not be of a smaller diameter than

that of the inlet port. Inlet pipes always have a diameter smaller than
outlet pipes. Choose preferably flexible pipes to avoid vibration
transmission.

• Tank: with suction pipe and return separated by baffles. If

necessary, use a heat exchanger to avoid oil heating above 70-80°C
and protect it from extreme pressure with a pressure relief valve.
Minimum approximate capacity: as twice as the circulation flow.

Pic. 4.9

1 Hdr pump 4 Oil filter

2 Distributor 5 * Heat exchanger

3 Hdr motor 6 * Safety valve

* optional components

• Starting-up: be sure that the system is well cleaned and pour oil
into the tank and into the motor housing (necessary to lubricate the
internal bearings).

• Vent the circuit and adjust the overpressure safety valve to the
lowest possible value.

• Check the oil tank level.

• Increase pressure and rotation speed until operating values are
reached.

• The machine/system manufacturer is responsible for dimensioning
the lines.

The machine/system manufacturer is responsible
for dimensioning the lines.

5.1. Pump starting-up

• Before starting the equipment check the lubricating oil level of the

pump.

• Refill the tank with lubrication oil.

• Check the oil level in the gear box (if the pomp is provided with it).

• In order to choose the most suitable oil, see paragraph. 2.5.

• Check that all protection and safety devices are correctly installed.

• Check that no obstacles obstruct the vacuum and pressure line or

the air injection cooling system.

• Check rotation direction: open all system valves and start running

at slow speed.

Do not rotate in the wrong direction:pump may be
damaged.

• Check which position of the 4-way integrated valve lever allows

vacuum or pressure functioning.

• If the pump has been in storage for a long time: inlet. liter of oil in

the pump for an easy cleaning of internal parts.

• Close the valve and increase vacuum rate (or operating pressure).

• Check loading and operating speed for vibrations or unusual

noises.

This vacuum pump is designed to work at
maximum speed. For longer operating we
recommend the pump be run at working speed.

• Prepare adequately transmission.

5.2. Operating precautions

• Run the vacuum pump at a room temperature of -20°C e +40°C.

• Do not make the vacuum pump overheat. Maximum air
temperature on exhaust (or delivery) side: 150°C.

• Do not operate the pump without lubrication: it may cause quick
wear and possible breakdown of vanes.

• Do not start running the pump under load: that causes stress to the
drive system and the hydraulic motor.

• Check rotation speed. The vacuum pump must never exceed the
maximum speed or run below the minimum speed.

• Do not accidentally operate the pump in the wrong direction: it may
break the vanes.

• Do not convey the exceeding delivery outlet towards the suction
port, otherwise it will sack warm gas.

• Control the air flow by adjusting the rotation speed: do not use the
pressure relief valve to discharge the exceeding flow.

• Once that the wanted vacuum rated has been attained it is
recommendable to decrease the speed. (see par. 2.3): This useful
procedure, that will not increase the time requested to fill up the tank,

5. Start up

5

4

6

1

3

P

A B

OUT IN

DRAINING LINE

4

6

3

5

2

1

REV. 01

19-07-2016

I

NSTALLATION, USE AND MAINTENANCE MANUAL –

PNR/PNE 104-124 – PNR 142

15 / 32

Jurop

SpA

Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)

TEL. +39 0

434 636811

FAX.

+39 0

434 636812

http://www.jurop.it

e-mail: [e-mail]

will however result in a lesser wear of the vanes. It is suggested to
reduce the speed also when operating with pressure.

• When, exhaust temperature is reduced, vane durability is

increased and both oil consumption and power absorption are reduced.

Once the needed vacuum rate has been reached,
we recommend reducing the vacuum pump
speed to its working speed.

• Internal wash-up is necessary after prolonged inactivity, after
working in dusty environments or in case of accidental suction of
liquids. Such operation must be carried out only on cooled pumps.

1. Disconnect the exhaust silencer, if possible;

2. Start running the pump at low speed;

3. Suck some water (about 1-2 litres) through the inlet port;

4. Then suck oil (about 1 litre) to complete the wash-up and lubricate

internal components.

In case the exhaust line cannot be disconnected,
drain the liquids accumulated in the separator of
the exhaust silencer.

• With temperature below 5 °C (40 °F) and long periods of inactivity,
introduce some quantity of oil through the suction connection before
starting off the pump.

• The air injection cooling system grants the use of the vacuum
pump at high vacuum rates. Anyway it has to be remembered that the
pump has been designed for non-continuous work. This cooling system
allows to dissipate part of the accumulated heat still at satisfactory
lubrication conditions. Continuous, heavy-duty work, or prolonged work
periods will cause an over-heating of the pump, consequently reducing
performances and durability.

• With the PNR models it is quite normal that the vacuum rate in the
tank will fall down at about 50%, if and when the pump is stopped for
sufficient time. This because atmosferic air will flow back in the tank
through the injection valves, which are adjusted at approximately 0,5
bar. Vent the tank and take it to atmospheric pressure when stopping
the pump in order to avoid back rotation of the pump.

6.1. Ordinary maintenance

• Installation and maintenance must be operated only by qualified personnel wearing the proper clothes and the necessary tools as well as

protection devices.

• Use suitable protection equipment (gloves, protection glasses, boots...)

• In the following table summarizes the main controls to be performed and the frequency of intervention.

Operating

Condition

Maintenance Area Check 8H 50H 500H 1000H

OPERATING

Vacuum line

Check safety valve (non-return valve)

Operating pressure

Transmission / Pump

Lubrication: dripping into oilers (PNR 142)

Rotation speed

Sound pressure level (also HDR motor)

STANDSTILL

Vacuum line

Suctions filters

4-way changeover valve: check and lubricate

Pump

Clean oilers glasses (PNR 142)

Check oil level

Check vanes wear

Change oil (*)

Pump’s inner washing (**)

Overall

Greasing

Check cardan shaft drive

Chack transmission pulley

(*)The first oil change must be done inside 500 hours operation. Following
changes every 5000 hours or 12 months. In order to choose the most suitable oil, see
paragraph 2.5.

(**) After operation in dusty environments, after accidental sucking of liquids
inside the pump or before a long inoperativity period it is recommended to wash the
pump inside according to the procedure described at paragraph 5.2.

Checking lubrification (PNR 142 only)

• Check dripping into the oilers.

• Be sure it is regular (about 60 drops/min at max. speed, with free

ports) to grant a correct lubrication of the pump. At lower speeds, the
number of drops must be directly proportional.

6. Maintenance

REV. 0

1

19-07-2016

I

NSTALLATION, USE AND MAINTENANCE MANUAL –

PNR/PNR 104-124 – PNR 142

16 / 32

Jurop

SpA

Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)

TEL. +39 0

434 636811

FAX.

+39 0

434 636812

http://www.jurop.it

e-mail: [e-mail]

If the pump is running without lubrication, the
internal components may quickly damaged due to
overheating. Stop the vacuum pump and check the
oil level and the lubricating pump.

Checking the oil tank level

• Check the oil tank level.

• Do not run the pump with oil level under the minimum level: that

may lead to dry functioning and cause serious damages. (Fig. 6.1).

• Check the oil level in the gear box (if the pomp is provided with it).

Pic. 6.1

• Rear mounted tank capacity: 3,2 l.

• Side mounted tank capacity: 4 l.

• Use pure and fresh oil. In order to choose the most suitable oil,

see paragraph 2.5.

Checking the vanes wear

• Unscrew the vanes wear check-plug on the front flange. See Pic.

6.2.

Pic. 6.2

• Turn the shaft by hand until vanes appearance.

• Vanes usually slip on seat bottom due to gravity. Check their right

entry in the seat.

• Insert a Ø 6 mm stick until it touches the rotor and then mark like

in Pic. 6.3.

• Turn the rotor slowly until the stick touches the vane in idle
position in its seat. The vanes slide to the bottom of the seat due to
gravity: check they really do and mark again on the stick.

• Repeat the same procedure for all the vanes. If wear exceeds 10
mm: replace the vanes as soon as possible.

Pic. 6.3

• Replace all the pump vanes at the same time.

Replace the vanes when their wear exceeds 10
mm (L – L min): they may break. Replace all
vanes at the same time.

• Replace the cap after the measurement.

6.2. Extraordinary maintenance

• Before starting any extraordinary maintenance operation, be sure
the pump stands still and follow the safety prescriptions as described in
Cap. “Safety and accident prevention”.

Replacing the vanes (PNR/PNE 104-124)

• Remove the vacuum pump from its bearing frame and wash it
before disassembling.

• It is suggested to remove the oil tank on the rear part because
generally the pump’s drive components are fitted on the front flange.
Use always the specific kit of gaskets for the pump model at hand (see
also spare parts list).

• Material that is subject to wear: replace.

Pic. 6.4

VANES

CHECK-PLUG

REAR MOUNTED TANK

SIDE MOUNTED TANK

REV. 01

19-07-2016

I

NSTALLATION, USE AND MAINTENANCE MANUAL –

PNR/PNE 104-124 – PNR 142

17 / 32

Jurop

SpA

Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)

TEL. +39 0

434 636811

FAX.

+39 0

434 636812

http://www.jurop.it

e-mail: [e-mail]

Pos. Code Description

1 1684000000 PLUG 3/8
2 1640101200 TANK’S CAP
3 1680707700 CAP’S GASKET
4 4026706101 PIPE’S FITTING
5 4024251000 OIL PUMP (RIGHT)

4024251500 OIL PUMP (LEFT)
6 4022200111 SEAL 72X48X15
7 16125006E0 OIL TANK
8 4022200309 OR
9 1610508500 PUMP’S FLANGE

10 4026300020 COMPENSATION RING
11 4023100140 BEARING

Disassemble operation

• Drain the oil tank through the proper port (pos. 1).

• Remove the tank’s cap (pos. 2) and change the gasket (pos. 3);
unscrew the lubrication pipe’s fittings (pos .4) connecting the oil pump
to the oilers.

• Remove the oil pump (pos .5).

• Remove the screws fixing the oil tank (pos. 7) and carefully
remove it, eventually using two screws partially winded inside the
threads. Avoid that the rotor falls down inside the housing, supporting it
if necessary with adequate tools.

• Change the OR (pos. 8).

• Remove the oil pump’s flange (pos. 9), the compensation ring
(pos. 10) and the bearing (pos. 11) this will make the reassembly of the
oil tank much easier (pos. 7).

• Lubricate the new vanes before inserting them in the rotor’s slots.

• The new vanes have to be inserted with the rounded corner facing
towards the housing (See Pic. 6.5).

Pic. 6.5

Assemble operation

• Reassemble everything again in the right sequence, absolutely
avoiding to leave foreign parts inside the pump. Always change all the
gaskets and the OR after having them properly lubricated and also the
seal (pos. 6) if necessary. ut some grease in the space between the
bearing (pos. 11) and the flange (pos. 9).

• Reassemble the oil tank (pos. 7) and the OR (pos. 8) carefully
inserting the drive shaft without damaging the seal.

• Insert the bearing (pos. 11), the compensation ring (pos. 10), and
the oil pump’s flange (pos. 9).

• Insert correctly the lubrication pump in the driving slot and refit the
flange.

• Reassemble the lubrication pipes and fittings.

• Reassemble the tank’s cap (pos. 2) and the gasket (pos. 3).

• Replace the plug on the tank (pos. 1) and refill it with lubrication
oil.

Replacing the vanes (PNR 142)

• Remove the vacuum pump from its bearing frame and wash it

before disassembling.

• It is suggested to remove the oil tank on the rear part because
generally the pump’s drive components are fitted on the front flange.
Use always the specific kit of gaskets for the pump model at hand (see
also spare parts list)

• Material that is subject to wear: replace.

Pic. 6.6

Pos. Code Description

1 1610508100 FLANGE
2 1610512900 PUM’S FLANGE
3 1642100200 REAR PROTECTION
4 4022200113 SEAL 70X55X15
5 4022200311 OR
6 4023100150 BEARING
7 4024251000 OIL PUMP (RIGHT)

4024251500 OIL PUMP (LEFT)
8 4026300025 COMPENSATION RING
9 4026706101 PIPE’S FITTING

Disassemble operation

• Remove the rear protection (pos. 3).

• Unscrew the lubrication pipe’s fittings connecting the oil pump

(pos. 9) to the oilers.

• Remove the oil pump (pos. 7).

• Remove the screws fixing the flange (pos. 1) and carefully remove
it, eventually using two screws partially winded inside the threads.
Avoid that the rotor falls down inside the housing, supporting it if
necessary with adequate tools.

• Change the OR (pos. 5).

• Remove the oil pump’s flange (pos. 2), the compensation ring (pos.

8) and the bearing (pos. 6) this will make the reassembly of the oil tank
much easier.

• Lubricate the new vanes before inserting them in the rotor’s slots.

• The new vanes have to be inserted with the rounded corner facing
towards the housing (See Pic. 6.5).

REV. 0

1

19-07-2016

I

NSTALLATION, USE AND MAINTENANCE MANUAL –

PNR/PNR 104-124 – PNR 142

18 / 32

Jurop

SpA

Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)

TEL. +39 0

434 636811

FAX.

+39 0

434 636812

http://www.jurop.it

e-mail: [e-mail]

1/2 giro

40 - 80 g/h

K

½ giro

40 – 80 g/h

Assemble operation

• Reassemble everything again in the right sequence, absolutely
avoiding to leave foreign parts inside the pump. Always change all the
gaskets and the OR (pos. 5) after having them properly lubricated and
also the seal (pos. 4) if necessary. Put some grease in the space
between the bearing (pos. 6) and the flange (pos. 1).

• Reassemble the flange (pos. 1), and the OR (pos. 5) carefully
inserting the drive shaft without damaging the seal (pos. 4).

• Insert the bearing (pos. 6), the compensation ring (pos. 8) and the
oil pump’s flange (pos. 2).

• Insert correctly the lubrication pump (pos. 7) in the driving slot and
refit the flange.

• Reassemble the lubrication pipes and fittings.

• Reassemble the rear protection (pos. 3).

General warnings

• On direct drive models normally it is not necessary to remove the
front small flange. However, if this has to be done do not forget to
grease the underneath bearing.

• The front bearing has been greased during pump’s assembling.
Lubrication of said bearing is necessary after long working periods only
(for example, normal duration of a set of vanes). It is consequentely
suggested to pump carefully new grease through the lubrication nipple
in order to avoid damages to the seals.

• When changing the vanes do not forget to carefully clean all the
components that you have dismantled. Clean the oil filter and the oil
tank from the solid sediments. The models PNR142, are provided with
a side oil tank; be careful to the maximum tight torque of the oil filter
plug. Maximum torque: 10Nm.

Mounting the hydraulic drive

• We recommend the drive coupling be oiled when vanes are being
replaced.

• However lubricate the drive coupling every 1500 hours.

We recommend the drive coupling be oiled every
1500 hours.

• Apply coupling hub to vacuum pump axis respecting the position
marked during disassembly: the grain must go back into the seat on the
rim.

• Mount the coupling and lubricate internally with NLGI 2 Lithium
grease. Provide an adequate quantity of fat, in order to have a medium
filling.

• Reassembly the motor without forcing onto the seals.

Adjusting the self-lubricating pump

• The automatic lubricating pump is adjusted by the manufacturer
before the shipping.

• If consumption noticeably differs from the indicated value, adjust it
as follows:

- Remove the upper protection cover;

- Using a screwdriver and a 10 mm wrench, adjust the adjusting

screw (K). Close the nut and remount the upper protection cover;

- It is advisable to turn the screw of ¼ of turn and verify the actual
consumption.

Pic. 6.7

Do not reduce oil consumption below the value
indicated in par. 2.2 (for functioning at speeds
different from the maximum, flow is proportionate
to rotating speed).

• ½ turn of the adjusting screw causes a variation in the flow of

approximately 40 - 80 g/h, depending on using conditions.

Cleaning of the inside exhaust port of the pump housing and
the 4-way manifolds

• Frequency: at every changing of the vanes.

• How to proceed: dismantle the manifold and remove possible

oilscales or other foreign parts.

• The clogging-up of this manifold and the exhaust port depends
mainly from heavy duty use of the pump and causes an increase of
temperature and a non perfect closing of the check valve. A careful
cleaning of all components, including the insides of the housing and the
non-return check valve and it’s seat, is therefore strongly
recommended.

REV. 01

19-07-2016

I

NSTALLATION, USE AND MAINTENANCE MANUAL –

PNR/PNE 104-124 – PNR 142

19 / 32

Jurop

SpA

Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)

TEL. +39 0

434 636811

FAX.

+39 0

434 636812

http://www.jurop.it

e-mail: [e-mail]

PROBLEMS

Cause Solution

•

Faulty lubrication

• Check the oil pump

•

Missing oil

• Fill up the oil tank

•

Revolutions to high

• Reduce the

speed

•

Operatin

g time too long at too high vacuum rate

• Decrease the vacuum rate

•

Clogged filters on the air injection system

• Clean the filters

•

Insufficient diameter of vacuum and discharge line

• Check the correct dimensions of the line (minimum suggested 3”)

Cause Solution

•

Brocken vanes

: •

Dismantle the pump and change the vanes

- due to foreign parts

• Check/clean the filters and elements on the vacuum line

- due to faulty lubrication

• Check the lubrication pump

•

Damaged

drive system

• Change the damaged parts

•

Frozen up pump

• Warm-up the pump

Cause Solution

• 4-

way valve handle in neutral position

• Move the handle against the resting pin

•

Worn vanes

• Change the vanes

• Leaking chec

k valve

•

Clean the check valve

•

Worn O

-

rings •

Change the seals

•

Leaking gaskets and/or valves on the vacuum tank

•

Change that damaged parts

• Clogged connecting pipeline

• Change the damaged hoses

- pipes

•

Floating ball or air filter obstructed

•

Dismantle and clean

•

Crusted up exhaust manifold

• Dismantle and clean

•

Vacuum line components under

-

dimensioned

• Check the dimensioning for the pump model at hand

•

Rubber connection obstructed or damaged

•

Change the connections

Cause Solution

•

Insufficient lubrication

• Adjust the oil pump flow

• Excessive oil consumption

•

Loss of adjustment of the oil pump

• Probable wear or breakage of the seal rings of the vacuum pump shaft.
Replace them

• Check the fittings built on the automatic oil pump and screw tight

• Before scrapping the machine, the following materials need to be

separated and suitably disposed of:

• Hydraulic oil.

• Rubber and plastic parts, such as hoses.

• Steel and aluminium parts.

• Recycling materials allow reducing the environmental impact and

respecting the environment.

Do not dispose of in the environment. Dispose of
in compliance with the standards in force.

Abnormal oil consumption

Reduced performa

nces

The pump is blocked

Overheating

8.

Scrapping

7. Malfunctions: troubleshooting

REV. 0

1

19-07-2016

S

PARE PART DATA SHEET –

PNR/PNE 104-124 D

20 / 32

Jurop

SpA

Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)

TEL. +39 0

434 636811

FAX.

+39 0

434 636812

http://www.jurop.it

e-mail: [e-mail]

PNR/PNE

104-124 D

PICTURE SHOWS

PNR

104

D

WITH SMOOTH SHAFT

COD

.

A690809440

REV. 01

19-07-2016

S

PARE PART DATA SHEET –

PNR/PNE 104-124 D

21 / 32

Jurop

SpA

Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)

TEL. +39 0

434 636811

FAX.

+39 0

434 636812

http://www.jurop.it

e-mail: [e-mail]

PNR/PNE 104-124 D

Pos. Codice Descrizione Q.tà Pos. Codice Descrizione Q.tà

1 1493300200 AIR INJECTION VALVE 1/2'' 2 35 16807009E0 GASKET 1
2 1601605900 VANE PNR 104 5 36 16807010E0 GASKET 1

1601606000 VANE PNR 124 5 37 16807011E0 GASKET 1
1601605500 VANE PNE 104 5 38 1680707300 GASKET 1

1601605600 VANE PNE 124 5 39 1680707700 GASKET 1
3 1605500100 HANDLE 1 40 1680707800 GASKET 1
4 16081001E0 DISTRIBUTOR 1 41 1683600300 OIL STICK 1
5 1608502500 CONVEYOR 1 42 1684000000 PLUG 3/8 4
6 16105005E0 FLANGE 1 43 1685002800 WASHER 30X8,5 SP.4 GALV. 1
7 1610508200 FLANGE 1 44 1685100200 WASHER 17X22X1,5 4
8 1610508500 OIL PUMP FLANGE 1 45 1685100800 WASHER 8X14X1,5 2
9 16120820E0 PLATE 2 46 16875020E0 HOUSING PNR-PNE 104 1

10 16120854E0 PLATE 1 16875019E0 HOUSINGPNR-PNE 124 1
11 16125006E0 OIL TANK 1 47 1691000000 CONVEYOR SPRING 1
12 1621503500 ROTOR PNR/PNE 104 1 48 18930008E0 CLAPET-VALVE 1

1621503600 ROTOR PNR/PNE 124 1 49 4022200030 SEAL 41X27X10 1

13 1622002600 SHAFT M10 1 50 4022200044 SEAL 65X45X8 1
14 1623100500 CAPPELLOTTO 1 51 4022200111 SEAL 72X48X15 1
15 1624007500 BUSHING 40X48X22 1 52 4022200113 SEAL 70X55X15 1
16 162409YKB0 SPACER 1 53 4022200309 OR 4875 VITON 2
17 1624202300 SPACER 1 54 4022300001 FILTER 1
18 1626001100 BUSHING 1 55 4022301001 OIL BLOCK FILTER ¼ 1
19 16275006E0 MANIFOLD 1 56 4022301004 OIL BLOCK FILTER ¾ 2
20 16401008E0 CLAPET CAP 1 57 4023100140 BEARING 6308 1
21 1640101200 OIL TANK CAP 1 58 4023100150 BEARING 6309 1
22 1642600000 PROTECTION 2 59 4023130035 BUSHING 55X45X22 1
23 1650014700 FRONT SMOOTH SHAFT 1 60 4024251000 OIL PUMP (RIGHT) 1

1650014600 FRONT SPLINED SHAFT 1 4024251500 OIL PUMP (LEFT) 1

24 1650014800 REAR SHAFT 1 61 4026102702 SCREW TE M 6X12 GALV. 5
25 1663014000 PIPE 2 62 4026102704 SCREW TE M 6 X 16 GALV. 4
26 1663041100 PIPE 1 63 4026102807 SCREW TE M 8 X 25 GALV. 27
27 16631022E0 PIPELINE 1 PNR-PNE 104 P.LUBR DX 1 64 4026121305 SCREW TCEI M 6 X 16 GALV. 2

16631028E0 PIPELINE 1 PNR-PNE 104 P.LUBR SX 1 65 4026121401 SCREW TCEI M 8 X 12 GALV. 2

16631018E0 PIPELINE 1 PNR-PNE 124 P.LUBR DX 1 66 4026121407 SCREW TCEI M 8 X 25 GALV. 16

16631026E0 PIPELINE 1 PNR-PNE 124 P.LUBR SX 1 67 4026135414 SCREW S.TESTA M 8X45 GALV. 1

28 16631023E0 PIPELINE 2 PNR-PNE 104 P.LUBR DX 1 68 4026135504 SCREW S.TESTA M 10 X 10 GALV. 1

16631029E0 PIPELINE 2 PNR-PNE 104 P.LUBR SX 1 69 4026300020 COMPENSATION RING 1

16631019E0 PIPELINE 2 PNR-PNE 124 P.LUBR DX 1 70 4026300025 COMPENSATION RING 1

16631027E0 PIPELINE 2 PNR-PNE 124 P.LUBR SX 71 4026308005 NUT M 8 ESAG. GALV. 2

29 16631025E0 PIPELINE PNR-PNE 104 DIST-CORPO DX 1 72 4026350505 WASHER GROWER 8 GALV. 16

16631024E0 PIPELINE PNR-PNE 104 DIST-CORPO SX 1 73 4026351504 WASHER M 6 GALV. 2

16631021E0 PIPELINE PNR-PNE 124 DIST-CORPO DX 1 74 4026351505 WASHER M 8 GALV. 27

16631020E0 PIPELINE PNR-PNE 124 DIST-CORPO SX 1 75 4026356001 WASHER 6X18 GALV. 3

30 16631032E0 PIPELINE PNR-PNE 104 DIST-FLANG DX 1 76 4026357003 WASHER M6 GALV. 4

16631031E0 PIPELINE PNR-PNE 104 DIST-FLANG SX 1 77 4026501006 TAB 12X8X56 1

16631034E0 PIPELINE PNR-PNE 124 DIST-FLANG DX 1 78 4026701301 FITTING 2

16631036E0 PIPELINE PNR-PNE 124 DIST-FLANG SX 1 79 4026702004 FITTING 4

31 16631033E0 PIPELINE PNR-PNE 104 FLANG-CORPO DX 1 80 4026702708 WASHER 1"½ 1

16631030E0 PIPELINE PNR-PNE 104 FLANG-CORPO SX 1 81 4026706000 FITTING 90°4X1/8 2

16631035E0 PIPELINE PNR-PNE 124 FLANG-CORPO DX 1 82 4026706003 FITTING 90° 6X1/8 2

16631037E0 PIPELINE PNR-PNE 124 FLANG-CORPO SX 1 83 4026706101 FITTING 2

32 1672001600 SCREW TCEI M10X1,5 10 84 4026706104 FITTING 1
33 1680609700 GASKET 1 85 4026904005 PLUG 1"½ 1
34 1680609800 GASKET 1 86 4029602806 PROTECTION 1

REV. 0

1

19-07-2016

S

PARE PART DATA SHEET –

PNR/PNE 104-124 M

22 / 32

Jurop

SpA

Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)

TEL. +39 0

434 636811

FAX.

+39 0

434 636812

http://www.jurop.it

e-mail: [e-mail]

PNR/PNE

104-124

CON MOLTIPLICATORE

PICTURE SHOWS

PNR

104

WITH MULTIPLIER

COD

.

A693209440

REV. 01

19-07-2016

S

PARE PART DATA SHEET –

PNR/PNE 104-124 M

23 / 32

Jurop

SpA

Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)

TEL. +39 0

434 636811

FAX.

+39 0

434 636812

http://www.jurop.it

e-mail: [e-mail]

PNR/PNE 104-124 with multiplier

Pos.

Code Description Q.ty Pos.

Code Description Q.ty

1 1493300200 AIR INJECTION VALVE 1/2'' 2 39 1680707700 GASKET 1
2 1601605900 VANE PNR 104 5 40 1680707800 GASKET 1

1601606000 VANE PNR 124 5 41 1683600300 OIL STICK 1

1601605500 VANE PNE 104 5 42 1684000000 PLUG 3/8 4

1601605600 VANE PNE 124 5 43 1685002800 WASHER 30X8,5 SP.4 GALV. 1
3 1605500100 HANDLE 1 44 1685100200 WASHER 17X22X1,5 4
4 16081001E0 DISTRIBUTOR 1 45 1685100800 WASHER RA 8X14X1,5 2
5 1608502500 CONVEYOR 1 46 16875020E0 HOUSING PNR-PNE 104 1
6 1610508500 FLANGE 1 16875019E0 HOUSING PNR-PNE 124 1
7 1610508700 FLANGE 1 47 1691000000 CONVEYOR SPRING 1
8 16120820E0 PLATE 2 48 18930008E0 CLAPET 1
9 16120854E0 PLATE 1 49 4022200030 SEAL 41X27X10 1

10 16125006E0 OILT TANK 1 50 4022200040 SEAL 72X40X10 1
11 1612503500 GEARBOX 1 51 4022200111 SEAL 72X48X15 1
12 1621503500 ROTOR PNR/PNE 104 1 52 4022200113 SEAL 70X55X15 1

1621503600 ROTOR PNR/PNE 124 1 53 4022200309 OR 4875 VITON 2

13 1622002600 SHAFT M10 1 54 4022300001 FILTER 1
14 1623100500 CONVEYOR CAP 1 55 4022301001 OIL BLOCK FILTER ¼ 1
15 1624007500 BUSHING 40X48X22 1 56 4022301004 OIL BLOCK FILTER ¾ 2
16 162409YKB0 SPACER 1 57 4023100110 BEARING 6206 1
17 1624202300 SPACER 1 58 4023100140 BEARING 6308 2
18 16275006E0 MANIFOLD 1 59 4023100150 BEARING 6309 1
19 16401008E0 CLAPET CAP 1 60 4023130035 BUSHING 55X45X22 1
20 1640101200 REAR COVER 1 61 4024251000 OIL PUMP (RIGHT) 1
21 1642600000 PIPELINE PROTECTION 2 4024251500 OIL PUMP (LEFT) 1
22 1650014500 FRONT SHAFT 1 62 4026102702 SCREW TE M 6X12 GALV. 5
23 1650014800 REAR SHAFT 1 63 4026102704 SCREW TE M 6 X 16 GALV. 4
24 1651005500 PINION 1 64 4026102802 SCREW TE M 8X12 GALV. 3
25 1651005700 GEAR 1 65 4026102807 SCREW TE M 8 X 25 GALV. 24
26 1663014000 PIPELINE 2 66 4026102808 SCREW TE M 8 X 30 GALV. 7
27 1663041100 PIPELINE 1 67 4026121305 SCREW TCEI M 6 X 16 GALV. 2
28 16631022E0 PIPELINE 1 PNR-PNE 104 P.LUBR. DX 1 68 4026121401 SCREW TCEI M 8 X 12 GALV. 2

16631028E0 PIPELINE 1 PNR-PNE 104 P.LUBR SX 1 69 4026121407 SCREW TCEI M 8 X 25 GALV. 16

16631018E0 PIPELINE 1 PNR-PNE 124 P.LUBR DX 1 70 4026135414 SCREW M 8X45 GALV. 1

16631026E0 PIPELINE 1 PNR-PNE 124 P.LUBR SX 1 71 4026135504 SCREW M 10 X 10 GALV. 1

29 16631023E0 PIPELINE 2 PNR-PNE 104 P.LUBR DX 1 72 4026300020 COMPENSATION RING 1

16631029E0 PIPELINE 2 PNR-PNE 104 P.LUBR SX 1 73 4026300025 COMPENSATION RING 1

16631019E0 PIPELINE 2 PNR-PNE 124 P.LUBR DX 1 74 4026306115 NUT M 36X3 ESAG. AUTOBL. 1

16631027E0 PIPELINE 2 PNR-PNE 124 P.LUBR SX 1 75 4026308005 NUT M 8 ESAG. GALV. 2

30 16631024E0 PIPELINE PNR-PNE 104 DIST.-CORPO SX 1 76 4026350505 WASHER GROWER 8 GALV. 16

16631025E0 PIPELINE PNR-PNE 104 DIST.-CORPO DX 1 77 4026351504 WASHER DENT.INT.M 6 GALV. 2

16631020E0 PIPELINE PNR-PNE 124 DIST.-CORPO SX 1 78 4026351505 WASHER DENT.INT.M 8 GALV. 29

16631021E0 PIPELINE PNR-PNE 124 DIST.-CORPO DX 1 79 4026356002 WASHER 8X24 GALV. 3

31 16631025E0 PIPELINE PNR-PNE 104 DIST.-CORPO DX 1 80 4026357003 WASHER M6 GALV. 4

16631024E0 PIPELINE PNR-PNE 104 DIST.-CORPO SX 1 81 4026501003 TAB 12X8X40 1

16631021E0 PIPELINE PNR-PNE 124 DIST.-CORPO DX 1 82 4026701301 FITTING 2

16631020E0 PIPELINE PNR-PNE 124 DIST.-CORPO SX 1 83 4026702004 FITTING 2

32 1672001600 SCEW TCEI M10X1,5 10 84 4026702708 WASHER 1"½ 1
33 1680609700 GASKET 1 85 4026706000 FITTING 90°4X1/8 2
34 1680609800 GASKET 1 86 4026706003 FITTING 90° 6X1/8 3
35 16807009E0 GASKET 1 87 4026706101 FITTING 2
36 16807010E0 GASKET 1 88 4026904005 PLUG 1"½ 1
37 16807011E0 GASKET 1 89 4029602806 PROTECTION SHAFT 1
38 1680707600 GASKET 1

REV. 0

1

19-07-2016

S

PARE PART DATA SHEET –

PNR 142 D

24 / 32

Jurop

SpA

Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)

TEL. +39 0

434 636811

FAX.

+39 0

434 636812

http://www.jurop.it

e-mail: [e-mail]

PNR 142 D

PICTURE SHOWS

PNR

142

D

(

SIDE MOUNTED TANK

)

1 2

REV. 01

19-07-2016

S

PARE PART DATA SHEET –

PNR 142 D

25 / 32

Jurop

SpA

Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)

TEL. +39 0

434 636811

FAX.

+39 0

434 636812

http://www.jurop.it

e-mail: [e-mail]

PNR 142 D

Pos.

Code Description Q.ty Pos.

Code Description Q.ty

1 1401200700 OIL DRIPPER 2 46 1687509500 HOUSING PNR 142 SL 1
2 1493300200 AIR INJECTION VALVE 1/2'' 2 47 1687600000 OIL TANK 1
3 1601605200 VANE 5 48 1691000000 CONVEYOR SPRING 1
4 1605500100 HANDLE 1 49 18930008E0 CLAPET 1
5 1608100000 DISTRIBUTOR 1 50 4022200030 SEAL 1
6 1608502500 CONVEYOR 1 51 4022200044 SEAL 65X45X8 1
7 1610508100 FLANGE 2 52 4022200113 SEAL 70X55X15 2
8 1610508200 FLANGE 1 53 4022200311 OR 4975 2
9 1610512900 FLANGE 1 54 4022300001 FILTER 1

10 1621503200 ROTOR 1 55 4022301004 FILTER 2
11 1622002600 SHAFT M10 1 56 4023100150 BEARING 6309 2
12 1623100500 CONVEYOR CAP 1 57 4023130035 BUSHING 55X45X22 2
13 162409YKB0 SPACER 1 58 4024251000 OIL PUMP (RIGHT) 1
14 1624042800 SPACER 2 4024251500 OIL PUMP (LEFT) 1
15 1624202300 SPACER 1 59 4026101301 SCREW TE M6X10 GALV. 2
16 1626001100 BUSHING 1 60 4026102804 SCREW TE M8X16 GALV. 3
17 16275007E0 MANIFOLD 1 61 4026102807 SCREW TE M8X25 GALV. 16
18 16401008E0 CLAPET CAP 1 62 4026102808 SCREW TE M8X30 GALV. 2
19 1642100200 REAR PROTECTION 1 63 4026102907 SCREW TE M10X25 GALV. 16
20 1642600100 CARDAN PROTECTION 1 64 4026121305 SCREW TCEI M6X16 GALV. 2
21 1650013100 FRONT SHAFT (SMOOTH) 1 65 4026121401 SCREW TCEI M8X12 GALV. 2

1650012900 FRONT SHAFT (SPLINED) 1 66 4026121407 SCREW TCEI M8X25 GALV. 8

22 1650022900 REAR SHAFT 1 67 4026121710 SCREW TCEI M12X35 GALV. 2
23 1663014000 PIPELINE 2 68 4026135414 SCREW M8X45 GALV. 1
24 1663065800 PIPELINE 1 69 4026135504 SCREW M10X10 GALV. 1
25 1663065900 PIPELINE 1 70 4026155605 SCREW TSPEI M6X16 GALV. 4
26 1663066000 PIPELINE 1 71 4026171211 SCREW M12X80 GALV. 2
27 1663066100 PIPELINE 1 72 4026300025 COMPENSATION RING 2
28 1663066300 PIPELINE 1 73 4026305508 NUT M12 ESAG. AUTOBLOCC. 2
29 1663066400 PIPELINE 1 74 4026308005 NUT M 8 ESAG. GALV. 2
30 1663066500 PIPELINE 1 75 4026350505 WASHER GROWER 8 GALV. 20
31 1672001600 SCREW TCEI M10X1,5 10 76 4026350508 WASHER GROWER 12 GALV. 2
32 1673001000 FITTING 1 77 4026351504 WASHER 6 GALV. 4
33 1680609700 GASKET 1 78 4026351505 WASHER 8 GALV. 8
34 1680610200 GASKET 2 79 4026351506 WASHER 10 GALV. 16
35 1680707300 GASKET 2 80 4026356002 WASHER PIANA 8X24 GALV. 3
36 1680707800 GASKET 1 81 4026357007 WASHER M12 GALV. 2
37 16807011E0 GASKET 1 82 4026501006 TAB 12X8X56 1
38 1681006600 PLATE 2 83 4026701301 FITTING 1/2X18 2
39 1681100200 PLATE 1 84 4026702000 FITTING 4X1/8 8
40 1684000000 PLUG 3/8 2 85 4026706000 FITTING UNIV.90° 4X1/8 2
41 1685002800 WASHER 30X8,5 ZINC. 1 86 4026706003 FITTING UNIV.90° 6X1/8 2
42 1685100000 WASHER 2 87 4026706101 FITTING 4-1/8 2
43 1685100200 WASHER 2 88 4026904503 PLUG 1
44 1685100300 WASHER 2 89 4026910103 PLUG 1
45 1685100800 WASHER 2 90 4026910601 PLUG 1/8' 2

Pos.

Code Description Q.ty Pos.

Code Description Q.ty

1 Flanged Manifold 2 Threaded Manifold

F1 1627504800 FLANGED MANIFOLD 1 F2 1627504900 THREADED MANIFOLD 1
F3 4026351505 WASHER M8 12 F3 4026351505 WASHER M8 12
F4 4026102807 SCREW M8X25 12 F4 4026102807 SCREW M8X25 12
F5 4026135504 SCREW M10X10 1 F5 4026135504 SCREW M10X10 1

REV. 0

1

19-07-2016

S

PARE PART DATA SHEET –

PNR 142 M

26 / 32

Jurop

SpA

Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)

TEL. +39 0

434 636811

FAX.

+39 0

434 636812

http://www.jurop.it

e-mail: [e-mail]

PNR 142

WITH MULTIPLIER

PICTURE SHOWS

PNR

142

M

(

WITH SIDE MOUNTED TANK

)

COD

.

A483209440

S

PARE PART DATA SHEET –

PNR 142 M

REV. 01

19-07-2016

27 / 32

Jurop

SpA

Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)

TEL. +39 0

434 636811

FAX.

+39 0

434 636812

http://www.jurop.it

e-mail: [e-mail]

PNR 142 with multiplier

Pos.

Code Description Q.ty Pos.

Code Description Q.ty

1 1401200700 OIL DRIPPER 2 52 1691000000 CONVEYOR SPRING 1
2 1493300200 AIR INJECTION VALVE 1/2'' 2 53 18930008E0 CLAPET 1
3 1601605200 VANE 5 54 4022200030 SEAL 1
4 1605500100 HANDLE 1 55 4022200040 SEAL 72X40X10 1
5 1608100000 DISTRIBUTOR 1 56 4022200113 SEAL 70X55X15 2
6 1608502500 CONVEYOR 1 57 4022200311 OR 4975 2
7 1610507900 FLANGE 1 58 4022300001 FILTER 2
8 1610508100 FLANGE 1 59 4022301004 FILTER 2
9 1610512900 FLANGE 1 60 4023100018 BEARING 6206 1

10 1612503000 GEARBOX 1 61 4023100040 BEARING 6308 1
11 1621503200 ROTOR 1 62 4023100150 BEARING 6309 2
12 1622002600 SHAFT M10 1 63 4023130035 BUSHING 55X45X22 2
13 1623100500 CONVEYOR CAP 1 64 4024251000 OIL PUMP (RIGHT) 1
14 162409YKB0 SPACER 1 4024251500 OIL PUMP (LEFT) 1
15 1624042800 SPACER 2 65 4026101301 SCREW TE M6X10 ZINC. 2
16 1624202300 SPACER 1 66 4026102804 SCREW TE M8X16 ZINC. 3
17 16275007E0 MANIFOLD 1 67 4026102807 SCREW TE M8X25 ZINC. 13
18 16401008E0 CLAPET CAP 1 68 4026102808 SCREW TE M8X30 ZINC. 9
19 1642100200 REAR COVER 1 69 4026102907 SCREW TE M10X25 ZINC. 13
20 1642600100 SHAFT PROTECTION 1 70 4026120506 SCREW TCEI M10X30 ZINC. 1
21 1650012800 FRONT SHAFT 1 71 4026121305 SCREW TCEI M6X16 ZINC. 2
22 1650022900 REAR SHAFT 1 72 4026121401 SCREW TCEI M8X12 ZINC. 2
23 1651005200 GEAR 1 73 4026121407 SCREW TCEI M8X25 ZINC. 8
24 1651005300 PINION Z 25 1 74 4026121710 SCREW TCEI M12X35 ZINC. 2
25 1663014000 PIPELINE 1 75 4026121813 SCREW TCEI M10X50 ZINC. 2
26 1663065800 PIPELINE 1 76 4026135414 SCREW M8X45 ZINC. 1
27 1663066000 PIPELINE 1 77 4026135504 SCREW M10X10 ZINC. 1
28 1663066300 PIPELINE 1 78 4026155505 SCREW TSPEI M5X16 ZINC. 4
29 1663066400 PIPELINE 1 79 4026155605 SCREW TSPEI M6X16 ZINC. 4
30 1663066500 PIPELINE 1 80 4026171211 SCREW M12X80 ZINC. 2
31 1663066700 PIPELINE 1 81 4026300025 COMPENSATION RING 2
32 1672001600 SCREW TCEI M10X1,5 10 82 4026305508 NUT M12 2
33 1673001000 FITTING 2 83 4026306115 NUT M36X3 1
34 1680609700 GASKET 1 84 4026308005 NUT M 8 2
35 1680610200 GASKET 2 85 4026350505 WASHER GROWER 8 GALV. 20
36 16807011E0 GASKET 1 86 4026350506 WASHER GROWER 10 GALV. 2
37 1680707200 GASKET 1 87 4026350508 WASHER GROWER 12 GALV. 2
38 1680707300 GASKET 1 88 4026351504 WASHER 6 GALV. 4
39 1680707800 GASKET 1 89 4026351505 WASHER 8 GALV. 10
40 1681006500 PLATE 1 90 4026351506 WASHER 10 GALV. 13
41 1681006600 PLATE 2 91 4026356002 WASHER 8X24 GALV. 3
42 1681100200 PLATE 1 92 4026357007 WASHER M12 GALV. 2
43 1684000000 PLUG 3/8 5 93 4026501004 TAB 12X8X45 1
44 1685002800 WASHER 30X8,5 ZINC. 1 94 4026701301 FITTING 1/2X18 2
45 1685100000 WASHER 2 95 4026702000 FITTING 4X1/8 6
46 1685100100 WASHER 1 96 4026706000 FITTING UNIV.90° 4X1/8 2
47 1685100200 WASHER 5 97 4026706003 FITTING UNIV.90° 6X1/8 2
48 1685100300 WASHER 2 98 4026706101 FITTING 4-1/8 2
49 1685100800 WASHER 2 99 4026904503 PLUG 1
50 1687509500 HOUSING PNR 142 SL 1 100 4026910103 PLUG 1
51 1687600000 OIL TANK 1 101 4026910601 PLUG 1/8' 2

REV. 0

1

19-07-2016

S

PARE PART DATA SHEET –

PNR/PNE 104-124

HDR AND ACCESSORIES

28 / 32

Jurop

SpA

Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)

TEL. +39 0

434 636811

FAX.

+39 0

434 636812

http://www.jurop.it

e-mail: [e-mail]

PNR/PNE 104-124 HDR and accessories

Pos.

Code Description Q.ty Pos.

Code Description Q.ty

H1 1470102300 COUPLING 1 3 1852103800 TURNING CONVEYOR Ø76
H2 1610021600 HDR FLANGE 1 C1 1610101100 CONVEYOR FLANGE 1
H3 1612501000 BRACKET HDR 1 C2 1627102800 CONVEYOR 1
H4 1680707300 GASKET 1 C3 4022200310 OR 1
H5 4024107009 HDR MOTOR PNR104 1 C4 4026102808 SCREW TE M8X30 GALV. 4

4024107001 HDR MOTOR PNR124 1 C5 4026350706 WASHER GROWER M8 GALV. 4

H6 4026103004 SCREW M12X40 GALV. 4
H7 4026121405 SCREW M8X20 GALV. 3 4 1852103900 TURNING CONVEYOR Ø80
H8 4026136003 SCREW M8X8 1 C1 1610101100 CONVEYOR FLANGE 1

H9 4026136006 SCREW M8X14 1 C2 1627102700 CONVEYOR 1
H10 4026171304 SCREW M14X40 4 C3 4022200310 OR 1
H11 4026308008 NUT M14 ESAG. GALV. 4 C4 4026102808 SCREW TE M8X30 GALV. 4
H12 4026350709 WASHER GROWER 12 GALV. 4 C5 4026350706 WASHER GROWER M8 GALV. 4
H13 4026350710 WASHER GROWER 14 GALV. 4
H14 4026350909 WASHER M8 3 5 1852104000 TURNING CONVEYOR Ø100
H15 4026359001 WASHER D.E.40X33,5X1,5 1 C1 1610101100 CONVEYOR FLANGE 1
H16 4026711003 FLANGE ASF 104G 1"1/4 1 C2 1627102400 CONVEYOR 1
H17 4026711004 FLANGE AFS 106G 1"1/2 1 C3 4022200310 OR 1
H18 4026904003 PLUG 1" GALV. 1 C4 4026102808 SCREW TE M8X30 GALV. 4

C5 4026350706 WASHER GROWER M8 GALV. 4

PNR/PNE

104-124 HDR

AND ACCESSORIES

3

4

5

5

S

PARE PART DATA SHEET –

PNR 142

AND ACCESSORIES

REV. 01

19-07-2016

29 / 32

Jurop

SpA

Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)

TEL. +39 0

434 636811

FAX.

+39 0

434 636812

http://www.jurop.it

e-mail: [e-mail]

PNR 142 HDR

AND ACCESSORIES

REV. 0

1

19-07-2016

S

PARE PART DATA SHEET –

PNR 142

HDR AND ACCESSORIES

30 / 32

Jurop

SpA

Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)

TEL. +39 0

434 636811

FAX.

+39 0

434 636812

http://www.jurop.it

e-mail: [e-mail]

PNR 142 HDR and accessories

Pos.

Code Description Q.ty Pos.

Code Description Q.ty

H1 1470103200 COUPLING 1 P11 4022200330 OR 3375 1

H2 1610021600 HDR FLANGE 1 P12 4022200331 OR 2137 1

H3 1612501000 BRACKET HDR 1 P13 4026102804 SCREW M8X16 4

H4 1680707300 GASKET 1 P14 4026102807 SCREW M8X25 4

H5 4024107004 HDR MOTOR 1 P15 4026121405 SCREW M8X20 4

H6 4026103004 SCREW M12X40 4 P16 4026350505 WASHER GROWER M8 4

H7 4026121405 SCREW M8X20 3 P17 4026351505 WASHER M8 8

H8 4026136003 SCREW M8X8 1 P18 4027100405 PNEUMATIC ACTUATOR 1

H9 4026136006 SCREW M8X14 1 P19 4027421206 FITTING 2
H10 4026141304 SCREW M14X40 4
H11 4026350709 WASHER GROWER M12 4 8 1852103400 FIXED CONVEYOR Ø80
H12 4026350710 WASHER GROWER M14 4 C1 1627101300 CONVEYOR Ø80 1
H13 4026308008 NUT M14 4 C2 4022200310 OR 6362 1
H14 4026350505 WASHER GROWER M8 3 C3 4026102807 SCREW M8X25 4
H15 4026359001 WASHER 1 C4 4026350706 WASHER GROWER M8 4
H16 4026904003 PLUG 1” 1

9 1852103500 FIXED CONVEYOR Ø100

6 143029KRB0 KIT HYDRAULIC ACTUATOR C1 1627101200 CONVEYOR Ø100 1

I1 143027T6B0 HYSRAULIC ACTUATOR 1 C2 4022200310 OR 6362 1
I2 15020A10B0 ACTUATOR LEVER 1 C3 4026102807 SCREW M8X25 4
I3 151307TJB0 ACTUATOR SUPPORT 1 C4 4026350706 WASHER GROWER M8 4
I4 1608502500 CONVEYOR 1
I5 1623100500 FLANGE 1 4 1852103900 TURNING CONVEYOR Ø80
I6 162409YKB0 SPACER 1 C1 1610101100 CONVEYOR FLANGE 1
I7 1624043400 SPACER 1 C2 1627102700 CONVEYOR 1
I8 1624202300 SPACER 1 C3 4022200310 OR 1

I9 164206XYB0 PROTECTION 1 C4 4026102808 SCREW TE M8X30 GALV. 4
I10 1673009700 GREASING NIPPLE 1 C5 4026350706 WASHER GROWER M8 GALV. 4
I11 1680707800 GASKET 1
I12 1685002800 WASHER 30X8.5X4 1 5 1852104000 TURNING CONVEYOR Ø100
I13 168509U0B0 WASHER 1 C1 1610101100 CONVEYOR FLANGE 1
I14 1691000000 SPRING 1 C2 1627102400 CONVEYOR 1
I15 4022100100 GREASER M6X1 1 C3 4022200310 OR 1
I16 4022100107 GREASER 1 C4 4026102808 SCREW TE M8X30 GALV. 4
I17 4022200030 SEAL 1 C5 4026350706 WASHER GROWER M8 GALV. 4
I18 4026121405 SCREW M8X20 2
I19 4026121408 SCREW M8X35 4 10 185212L4B0 KIT SUCTION FILTER
I20 4026135414 SCREW M8X45 1
I21 4026155705 SCREW M8X16 1
I22 4026308005 NUT M8 4
I23 4026350505 WASHER GROWER M8 6
I24 4026510012 SEEGER 1

7 143028G1B0 KIT PNEUMATIC ACTUATOR

P1 160858KBB0 CONVEYOR 1
P2 161258H0B0 ACTUATOR SUPPORT 1
P3 1640580QB0 ACTUATOR COVER 1
P4 167007ZAB0 CONVEYOR NUT 1
P5 1680707800 GASKET 1
P6 168409PQB0 RING NUT 1
P7 168529TFB0 SPACER 1
P8 1691000200 CONVEYOR SPRING 1
P9 4022100100 IGREASING NIPPLE M6X1 1

P10 4022200005 Y-SEAL 37X27X7 1

REV. 01

19-07-2016

31 / 32

Jurop

SpA

Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)

TEL. +39 0

434 636811

FAX.

+39 0

434 636812

http://www.jurop.it

e-mail: [e-mail]

REV. 0

1

19-07-2016

S

PARE PART DATA SHEET –

PNR 142

HDR AND ACCESSORIES

32 / 32

Jurop

SpA

Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)

TEL. +39 0

434 636811

FAX.

+39 0

434 636812

http://www.jurop.it

e-mail: [e-mail]

Model Issue date Revision No. Revision date Filled out by Viewed by

PNR/PNE 06-06-2016 01 19-07-2016 U.T. A.T.

Jurop SpA

Via Crosera, 50
33082 Azzano Decimo, PN (ITALY)

Tel. [phone]
Fax. [phone]

http://www.jurop.it
e-mail: [e-mail]

Jurop SpA reserves the right to modify the products described in this manual without prior notice.