jurop PN 130, PN 155R, PN 140, PN 155 Instructions For Installation, Use And Maintenance Manual
I
I
NNSSTTAALLLLAATTIIOON
N
,
,
UUSSEE AANNDD
MMAAIINNTTEENNAANNCCEE MMAANNUUAAL
L
EN
PN 130
-
140
-
155
-
155R
Rev. 0
7
23-04-2015
O
O
RRIIGGIINNAALL IINNSSTTRRUUCCTTIIOONNS
S
REV. 0
7
23-04-2015
I
NSTALLATION, USE AND MAINTENANCE MANUAL –
PN130-140-155-155R
2 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
2015 – Jurop
– Azzano D
ecimo (PN)
Reproduction, electronic storage and dissemination, even partial, are prohibited.
Jurop reserves the right to modify the products described in this manual without prior notice.
Any product names mentioned herein are the trademarks of their respective owners.
I
NSTALLATION, USE AND MAINTENANCE MANUAL –
PN130-140-155-155R
REV. 07
23-04-2015
3 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
Contents
1. General warnings
pag. 4
1.1 Introduction 4
1.2 Spare part request 4
1.3 Warranty terms and conditions 4
2. Technical data
pag. 5
2.1 Dimensions PN130 – PN140 5
2.2 Dimensions PN155 – PN155R 7
2.3 Usage Limitations 9
2.4 Performances 9
2.5 Lubrication
9
3. Safety and accident prevention
pag. 10
3.1 General recommendations 10
3.2 Intended use 10
4. Installation
pag. 10
4.1 Checking upon receipt 11
4.2 Mounting 11
4.3 Vacuum – pressure line 11
4.4 Pump mounting - Drive connection 12
5. Start up
pag. 13
5.1 Starting-up of the pump 13
5.2 Precautions when starting the system 14
6. Maintenance
pag. 14
6.1 Ordinary maintenance 14
6.2 Extraordinary maintenance 15
7.
Malfunctions:
troubleshooting
pag. 17
8. Scrapping
pag. 17
S
PARE PART DATA SHEET –
PN130-140-155-155R M 18
S
PARE PART DATA SHEET –
PN130-140-155-155R D 23
S
PARE PART DATA SHEET –
PN130-140-155-155R HDR 28
S
PARE PART DATA SHEET –
PN155 SP – PN155R SP 30
S
PARE PART DATA SHEET –
HDR
ACTUATOR
PN130-140-155 31
S
PARE PART DATA SHEET – PNEUMATIC ACTUATOR
PN130-140-155 32
I
NTEGRATION 1 – ADJUSTING THE
4-W
AY VALVE WITH PNM
ACTUATOR
33
REV. 0
7
23-04-2015
I
NSTALLATION, USE AND MAINTENANCE MANUAL –
PN130-140-155-155R
4 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
1.1. Introduction
This booklet contains the necessary instructions for a correct
installation, running, use and maintenance of the pump, as well as
some practical suggestions for a safe operating.
The knowledge of the following pages will grant a long and troublefree operation of the pump.
It is recommended to:
• Understand and apply carefully the instructions before running the
pump.
• Keep the booklet at hand and have it known to all operators.
Below is a brief description of the symbols used in this manual.
If these safety rules are not respected, operators can
be injured and the pump or oilers damaged
remarkably.
If these safety rules are not respected, the pump or
system can be damaged.
Suggestions for an environment friendly use of the
pump.
Useful information for an easy usage and
maintenance of the pump.
• Pump has to be fitted with its own tag reporting the following data:
Model, Serial number, Year, Max speed, Max pressure.
Fig. 1.1
1.2. Spare part request
• Use only genuine spare parts for maintenance and repairs. To
order spare parts, provide the following details:
EXAMPLE:
a) The model of the pump (see pump tag): PN130
b) The serial number of the pump (see pump tag): K40001
c) A description of the parts (see parts list): Oil tank
d) The quantity (see parts list): n°1 pz
e) The code number of the part (see parts list):
15840 094 00
1.3. Warranty terms and conditions
• Compliance with the installation, use and maintenance instructions
provided by this manual is crucial for the recognition of warranty
against defective parts.
1
. General warnings
I
NSTALLATION, USE AND MAINTENANCE MANUAL –
PN130-140-155-155R
REV. 07
23-04-2015
5 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
Pump PN130 – PN140 – PN155
• Rotary vacuum pump with radial vanes and air cooling system.
• Automatic lubrication with volumetric pump and side mounted tank.
• Built-in vacuum-pressure change-over valve.
• Non return valve (rubber ball) inside pump manifold.
• Aluminium conveyors.
• Direct drive with smooth shaft, right or left rotation.
• Gear box drive (splined shaft ASAE 1 3/8) 540 rpm or 1000 rpm,
left rotation.
• Direct drive with splined shaft ASAE 1 3/8, left rotation.
• Hydraulic drive with gear motor, left rotation.
Pump PN155R
As model PN155. In addition:
• Extra air injection cooling system.
• High resistant vanes.
Other features on request
• Rotation other than the standard one.
• Pneumatic or hydraulic actuator for the 4-way valve.
• Flanged manifolds are available on request.
Weight PN130 PN140 PN155 - PN155R
Direct drive 165 kg 173 kg 194 kg
With multiplier (540 rpm or 1000 rpm) 186 kg 194 kg 216 kg
Hydraulic drive with gear motor 197 kg 205 kg 227 kg
2.1. Dimensions PN130 – PN140
Versions smooth shaft and splined shaft – PN130 – PN140
PN130 D smooth shaft, L rotation - cod. A450909410 PN130 D smooth shaft, R rotation - cod. A450809410
PN130 D left splined shaft - cod. A450709410
PN140 D smooth shaft, L rotation - cod. A200909410 PN140 D smooth shaft, R rotation - cod. A200809410
PN140 D left splined shaft - cod. A200709410
A B C D E
PN130 D
550 776 376 234 175
PN140 D
568 806 406 249 180
LS: Tank level
CS: Tank load
OL: Oilers
2
. Technical data
VACUUM
RELIEF
VALVE CONNECTION
REV. 0
7
23-04-2015
I
NSTALLATION, USE AND MAINTENANCE MANUAL –
PN130-140-155-155R
6 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
VACUUM
RE
LIEF
VALVE CONNECTION
Versions with multiplier – PN130 – PN140
PN130 M 540 rpm, L rotation – cod. A453209410 PN130 M 1000 rpm, L rotation – cod. A453509410
PN140 M 540 rpm, L rotation – cod. A203209410 PN140 M 1000 rpm, L rotation – cod. A203509410
A B C D E F G
PN130 M
550 874 474 333 419 70 53
PN140 M
568 904 493 348 434 65 58
Hydraulic versions – PN130 – PN140
PN130 HDR, L rotation – cod. E458009410 PN130 HDR, L rotation – cod. E458109410
PN140 HDR, L rotation – cod. E208009410 PN140 HDR, L rotation – cod. E208109410
A B C D E
PN130 HDR
550 1040 644 499 144
PN140 HDR
568 1070 659 514 149
Hydraulic power parameters.
Motor Displacement Operating Pressure Max. Flow
72 cc/giro 150 bar 100 l/min
LS: Tank level
CS: Tank load
OL: Oilers
LM: Oil level
SM: Outlet plug
CM: Inlet plug
LS: Tank level
CS: Tank load
OL: Oilers
VACUUM
RELIEF
VALVE CONNECTION
VANES WEAR CHECK PORT
I
NSTALLATION, USE AND MAINTENANCE MANUAL –
PN130-140-155-155R
REV. 07
23-04-2015
7 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
2.2. Dimensions PN155 – PN155R
Versions smooth shaft and splined shaft – PN155 – PN155R
PN155 D smooth shaft, L rotation – cod. A350709410
PN155 D left splined shaft – cod. A350909410 PN155 D smooth shaft, R rotation – cod. A350809410
PN155R D smooth shaft, L rotation – cod. A360709410
PN155R D left splined shaft – cod. A360909410 PN155R D smooth shaft, R rotation – cod. A360809410
Note: pumps PN155 and PN155R are also available for the American market, with smooth board with size in inches.
Versions with multiplier – PN155 – PN155R
PN155 M 540 rpm, L rotation – cod. A353209410 PN155 M 1000 rpm, L rotation – cod. A353509410
PN155R M 540 rpm, L rotation – cod. A363209410 PN155R M 1000 rpm, L rotation – cod. A363509410
VACUUM
RELIEF
VALVE
CONNECTION
HDR
ACTUATOR
PNEUMATIC
ACTUATOR
VACUUM
RELIEF
VALVE
CONNECTION
HDR
ACTUATOR
PNEUMATIC
ACTUATOR
REV. 0
7
23-04-2015
I
NSTALLATION, USE AND MAINTENANCE MANUAL –
PN130-140-155-155R
8 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
Hydraulic versions – PN155 – PN155R
PN155 HDR, right rotation – cod. E358109410 PN155R HDR, right rotation – cod. E368109410
Hydraulic power parameters.
Motor Displacement Operating Pressure Max. Flow
86 cc/giro 140 bar 100 l/min
Versions with aluminium conveyors
PN155 FL 540 rpm, left rotation – cod. A353219410
Note: The vacuum pump PN155 may be equipped with aluminium conveyors.
• Kit fixed conveyor Ø100 with valve connection: cod. 18521 035 00
• Kit swivelling conveyor Ø100: cod. 18521 040 00
• Kit valve connection: cod. 18521 041 00
VACUUM
RELIEF
VALVE
CONNECTION
HDR
ACTUATOR
PNEUMATIC
ACTUATOR
I
NSTALLATION, USE AND MAINTENANCE MANUAL –
PN130-140-155-155R
REV. 07
23-04-2015
9 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
2.3. Usage limitations
Pump
Max. Speed
– Operating speed (RPM)
P2 (bar ABS) T
2
(°C)
T
2
- T
1
(°C)
M - 540 M - 1000 D - HDR
PN130 – PN140 540 – 460 rpm 1000 – 850 rpm 1350 – 1100 rpm 2 bar 150°C 130°C
PN155 – PN155R 540 – 470 rpm 1000 – 900 rpm 1150 – 1000 rpm 2 bar (*) 150°C 130°C
P1: absolute pressure during suction T1: temperature during suction
P2: absolute pressure during delivery T2: temperature during delivery
(*) : Belt drive only for PN155 D and PN155R D: P2= 1,5 abs bar
2.4. Performances
Performances referred to vacuum pump operating at max. speed.
Pump
Air flow (free
air condition)
Air flow at
60% vac.
Max.
vacuum
Power required at
max. vacuum
Vacuum at
continuous duty
Oil
consumption
Sound p.
level (**)
PN130 12900 l/min 11400 l/min 94% 19 kW 60% 240 g/h 78 dB (A)
PN140 13850 l/min 12300 l/min 92% 19 kW 60% 240 g/h 79 dB (A)
PN155 15200 l/min 13500 l/min 93%
19 kW
23 kW (2 bar abs)
60% (PN155)
70% (PN155R)
240 g/h 79 dB (A)
(**) : Only when decompressor at max. speed, 60% vacuum rate, 7 m distance in open field.
REFERENCE CONDITIONS
Conveyed gas: air Functioning in free air Reference abs. pressure: 1.013 mbar
Reference temperature: 20°C Vacuum functioning: free outlet Pressure functioning: free inlet
2.5. Lubrication
Recommended lubricants: SIDE MOUNTED OIL TANK LEVEL
Room
Temp.
Viscosity Type ENI ESSO SHELL TOTAL MOBIL BP
TEXACO
HAVOLINE
Under 10°C ISO VG 46 Olio minerale Acer 46 Nuto 46 Morlina oil 46 Drosera MS 46 Nuto H 46 Bartran HV 46 Rando HD 46
Over 10°C ISO VG 150 Olio minerale Acer 150 Nuto 150 Morlina oil 150 Drosera MS 150 Nuto H 150 Bartran HV 150 Rando HD 150
Recommended lubricants: GEAR BOX OIL
Viscosity Type ENI ESSO SHELL TOTAL MOBIL BP
TEXACO
HAVOLINE
ISO VG 220 Olio minerale EP Blasia 220 Spartan EP 220 Omala oil 220 Carter EP 220 Mobilgear 630 Energol GR XP 220 Meropa 220
REV. 0
7
23-04-2015
I
NSTALLATION, USE AND MAINTENANCE MANUAL –
PN130-140-155-155R
10 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
Attention: carefully apply these prescriptions.
3.1. General recommendations
• Installation and maintenance must be carried out with the unit
totally disengaged from its drive system and must be performed by
qualified personnel.
• Use adequate clothing (avoid ties, loose sleeves, necklaces and
so on) and suitable protection equipments (gloves, protection glasses,
boots...).
• When transporting the pump, use proper slinging. Store the pump
in stable places.
• Make sure that all the parts of the unit are idle and cool, before
performing any maintenance operation.
• Before each maintenance operation, stop the pump and restore
the atmospheric pressure.
• When the pump is running, some parts may reach very high
temperatures (above 100°C). Use all necessary precautions to avoid
contact.
• Operators working nearby must avoid prolonged exposure to the
noise emitted by the aspirator, if not equipped with the proper earprotection devices.
• Avoid accidental suction of solids: solids may be projected at high
speed through the exhaust manifold and cause injures.
• Do not start the machine if the protection devices provided for
transmissions are removed. Replace damaged parts.
• Pressure relief valve: point the air flux away from the operators.
• Do not use the aspirator over its designed limits: the machine may
be damage and the operator may be injured.
Do not exceed the power supply parameters
indicated in the technical tables (see par. 2.3).
3.2. Intended use
• The vacuum pump PN130, PN140 and PN155 are designed to
convey filtered air into systems for the vacuum production or for the
suction of powders or liquid wastes. Any other usage shall be
considered improper.
• Do not sack toxic substances and inflammable or explosive
gasses, since the internal components of the pump may reach high
temperatures.
• Liquids or solids infiltrations can seriously damage the pump.
• Do not run the pump over its designed operating limits (see par.
2.3): it may break and transmission can be damaged.
Legend main components
A.
Multiplier gear box
E.
Vacuum relief valve connection
I.
Air injection valve (only for PN155)
B.
Manifold
F.
Oil tank
J.
Swivelling conveyor
C. Vacuum
– pressure manifold
G.
Oilers
K. Conveyor with safety valve con
nection
D.
Non return valve
H.
Lubrication pump
4.
Installation
3.
Safety and accident pre
vention
I
NSTALLATION, USE AND MAINTENANCE MANUAL –
PN130-140-155-155R
REV. 07
23-04-2015
11 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
4.1. Checking upon receipt
• When the goods are delivered, make sure that all parts listed on the
delivery note are in perfect condition and have suffered no damage during
shipping.
• Make sure the vacuum pump has its identification plate affixed on the
front cover. Pumps without such identification are to be considered
anonymous and potentially dangerous: in such an event, they must not be
used, otherwise the manufacturer will be deemed free from any liability
whatsoever.
4.2. Mounting
• The pump must be assembled for an easy access for maintenance
operations and secured rigidly to a frame or levelled base (max. 3°
slant to the horizontal plane). The base must be such as to avoid
vibrations, bending or deformation.
• The oil tank is mounted on the suction side of the unit. Thus, the rotation
direction determines the pump overall dimensions. See par. 2.1.
• Make sure there is enough room around the pump for the air for the
cooling system to freely circulate and avoid exposure to dirt and debris.
Prepare enough room for an easy access to:
1. Vanes wear check port
2. Oilers
3. Oil tank level
4. Oil tank inlet plug
5. Oil tank outlet plug
6. Self-lubricating pump
7. Gear box oil level
8. Gear box oil outlet plug
9. Gear box oil inlet plug
10. 4-way valve handle
4.3. Vacuum – Pressure line
* optional components
V
ACUUM-PRESSURE LINE COMPONENTS
1 Primary flow shutoff valve
2 Secondary shutoff
3 Suction filter
4 Exhaust silencer with oil separator
5 (*) Over-pressure safety relief valve
6 (*) Vacuum relief valve
5 6
1
2
3
4
REV. 0
7
23-04-2015
I
NSTALLATION, USE AND MAINTENANCE MANUAL –
PN130-140-155-155R
12 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
α
α1
α
α1
• In order to avoid accidental suction of liquids inside the pump,
install a primary (pos. 1) and a secondary flow shutoffs (pos. 2). If
necessary, install also a suction filter (pos. 3) to protect from solids
infiltration.
• The exhaust silencer is designed to reduce the noise level and to
separate the oil mist coming out from the pump outlet port. The
separator must be periodically drained from oil and condensate
accumulated in the separator during the normal pump functioning.
• The diameter of the vacuum/pressure line pipes must be properly
dimensioned to the pump flow and, in any case, larger than the
diameter of the ports (Ø100 is recommended).
• The pipes weight must not solicit the body of the pump. Use high
temperature resistant rubber connections.
• Before mounting the vacuum line to the pump, remove the port
protections. Pipes and all line components must be clean.
• Avoid restrictions and tight curves as much as possible if not
strictly necessary.
• Exhaust pipes can reach high temperatures. Hence, they must be
properly isolated.
• Max. pressure safety valve on delivery: mount it close to the pump.
The valve flow must prevent the PN130 - PN140 - PN155 from
exceeding the absolute operating pressure (see par. “Usage
limitations”) or, in any case, the maximum pressure allowed by the
system. Do not apply gate valves on the line.
• Over-pressure safety relief valve (pos. 6): to apply if necessary to
limit the vacuum rate in the system.
4.4. Pump mounting - Drive connection
A) Cardan shaft drive
• Use telescopic cardan shafts.
Fig. 4.1
• In order to achieve a uniform motion of the driven shaft, the
following requirements must be met (see Fig. 4.1):
- Equal working angle α and α1 of both couplings.
- The internal fork joints must be coplanar.
- Both driven and driving shafts must be coplanar.
• It is also recommended working with limited articulated joint angles
(max. 15°) and disengaging the transmission for those operations
requiring great angles (steering or lifting).
Follow the rotation direction as indicated on the
front flange. Follow the instructions of the cardan
shaft’s manufacturer.
• Use the protection that comes with the pump shaft.
Use the cardan protection supplied with the
pump. The pump installation must fulfil the
current EC injury prevention specifications.
B) Belt drive
Fig. 4.2
• Install a suitable pulley on the smooth shaft as close as possible
to the pump: L max 35 mm.
• Apply an adequate belt tension (see manufacturer’s data). T Max
3000N.
• Do not use driven or driving pulleys with a pitch diameter inferior
to 180 mm. Small pulleys require a high belt tension which may cause
premature wear to the bearing or transmission troubleshooting.
• If the pump PN155 is run through a belt drive, its working pressure
must not exceed 1.5 abs. bars to prevent it from absorbing a power
requiring an excessive belt tension. There is no limit to the operation in
vacuum.
Attention: If the pump PN155 is run through a belt
drive, its working pressure must not exceed 1.5
abs.
Pump Drive min. pulley p. diam. Belts Max. Speed Max. Pressure Max. Vacuum.
PN130 180 mm SPB x 3 1350 rpm 2 bar abs 94%
PN140 180 mm SPB x 3 1350 rpm 2 bar abs 92%
PN155 180 mm XPB x 3 1150 rpm 1,5 bar abs 93%
CHECK BELT TENSION
Dp= 180 MIN
KEEP AXELS PARALLEL
ALIGN PULLEY GROVES AND BELTS
T MAX
I
NSTALLATION, USE AND MAINTENANCE MANUAL –
PN130-140-155-155R
REV. 07
23-04-2015
13 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
5
4
6
1
3
P
A B
OUT IN
DRAINING LINE
5
4
6
3
2
1
C) Hydraulic drive
Motor features for pump PN130 - PN140
Displacement
Max. operating
pressure
Max pressure
draining line
Max. press.
motor exhaust
72 cc/rev 235 bar 5 bar 5bar
Motor features for pump PN155
Displacement
Max. operating
pressure
Max pressure
draining line
Max. press.
motor exhaust
86 cc/rev 220 bar 5 bar 5bar
• Fluid: mineral oil for hydraulic systems in compliance with
ISO/DIN.
Temperature Optimum viscosity ale Max. viscosity allowed
-20 / +80 °C 12 – 100 cSt 750 cSt
• Filtration: class 19/16 contamination according to ISO 4406 to be
obtained with a ßx = 75 filter.
• Check circuit connections: they must be applied in the same
rotation direction as that indicated by the arrow on the pump front
flange.
Fig. 4.3
• Draining: connect directly to the tank above the maximum oil
level. Operating without draining line may damage the motor.
1 Hdr pump 4 Oil filter
2 Distributor 5 * Heat exchanger
3 Hdr motor 6 * Safety valve
* optional components
Fig. 4.4
• Distributor: open-centre distributor in central idle position
(vacuum pump off). It must be equipped with an adjustable
overpressure safety valve.
• Motor pipeline: outlet pipe must not be of a smaller diameter than
that of the inlet port. Inlet pipes always have a diameter smaller than
outlet pipes. Choose preferably flexible pipes to avoid vibration
transmission.
• Tank: with suction pipe and return separated by baffles. If
necessary, use a heat exchanger to avoid oil heating above 70-80°C
and protect it from extreme pressure with a pressure relief valve.
Minimum approximate capacity: as twice as the circulation flow.
• Starting-up: be sure that the system is well cleaned and pour oil
into the tank and into the motor housing (necessary to lubricate the
internal bearings).
• Vent the circuit and adjust the overpressure safety valve to the
lowest possible value.
• Check the oil tank level.
• Increase pressure and rotation speed until operating values are
reached.
5.1. Starting-up of the pump
• Check oil levels in gearbox and side mounted tank.
• Check that all protection devices are correctly installed.
• Check that there are no obstacles in the vacuum line.
• Check rotation direction: open all system valves and start running
slowly.
Do not rotate in the wrong direction: this may
damage the vacuum pump. Follow the arrow
indicated on the front flange.
• Check which position of the four-way integrated valve lever allows
vacuum or pressure functioning.
• Close the valve and increase vacuum rate (or operating pressure
)
.
• Check that the lubricating pump works properly. Oil must regularly
drip into the oilers. Typically (with degree of vacuum > 50%) about 40
drops/min (at maximum speed).
• Check loading and operating speed for vibrations or unusual
noises.
This vacuum pump is designed to work at
maximum speed, but for longer operating we
recommend the pump be run at working speed
(see par. 2.3). Adequately prepare the
transmission
• Prepare adequately transmission.
5. Start up
REV. 0
7
23-04-2015
I
NSTALLATION, USE AND MAINTENANCE MANUAL –
PN130-140-155-155R
14 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
5.2. Operating precautions
• Do not make the vacuum pump overheat: maximum air
temperature on exhaust (or delivery) side: 150°C.
• Do not operate the pump without lubrication: it may cause quick
wear and possible breakdown of vanes.
• Do not start running the pump under load: this may damage the
drive system or the hydraulic motor.
• Check the rotation speed: it must never exceed the operating limits
indicated on the identification plate of the vacuum pump.
• Do not accidentally operate the pump in the wrong direction: it may
break the vanes.
• Do not convey the exceeding delivery outlet towards the suction
port, otherwise it will sack warm gas.
• Control the air flow by adjusting the rotation speed: do not use the
pressure relief valve to discharge the exceeding flow.
• Internal wash-up is necessary after prolonged inactivity, after
working in dusty environments or in case of accidental suction of
liquids.
Such operation must be carried out only on cooled pumps.
1. Disconnect the exhaust silencer, if possible;
2. Start running the pump at low speed;
3. Suck some water (about 1-2 litres) through the inlet port;
4. Then suck oil (about 1 litre) to complete the wash-up and lubricate
internal components.
In case the exhaust line cannot be disconnected,
drain the liquids accumulated in the separator of
the exhaust silencer.
• Once the needed vacuum rate has been reached, we recommend
reducing the vacuum pump speed to its working speed (see par. 2.3):
this allows keeping the achieved vacuum/pressure rate constant. The
pump speed can also be reduced to values lower than the working
speed during the tank discharging phase (with the 4-way valve in
pressure mode) without increasing the draining time.
• Thus, exhaust temperature is reduced, vane durability is increased
and both oil consumption and power absorption are reduced.
Once the needed vacuum rate has been reached,
we recommend reducing the vacuum pump
speed to its working speed.
•
Installation and maintenance must be operated only by qualified personnel wearing the proper clothes and the necessary tools as well as
protection devices.
•
In the following table summarizes the main controls to be performed and the frequency of intervention.
Operating Condition Maintenance Area Checking 8H 50H 500H 1500H
O
PERATING
Transmission Rotation speed
Pump
Lubrication: dripping into oilers
Working pressure
Noise level
S
TANDSTILL
Pump
Clean oilers glasses
Clean filter and va
cuum line shutoff
- Drain the oil gathered in the exhaust
separator.
Check vanes wear
Check pressure relief valve condition
Side mounted tank oil level
Gearbox oil level
Gearbox oil change (*)
Pump’s inner washing (**)
(*) In order to choose the most suitable oil, see paragraph 2.5.
(**) After operation in dusty environments, after accidental sucking of liquids
inside the pump or before a long inoperativity period it is recommended to wash the
pump inside according to the procedure described at paragraph 5.2.
6.1. Ordinary maintenance
Checking the drip oilers
• Check dripping into the oilers.
• Be sure it is regular (about 40 drops/min at max. speed, with
degree of vacuum > 50%) to grant a correct lubrication of the pump. At
lower speeds, the number of drops must be directly proportional.
Checking the side mounted oil tank level
• Do not run the pump with oil level under the
minimum level: that may lead to dry functioning
and cause serious damages.
• Tank capacity: 4l.
• Use pure fresh oil.
Do not re-use the exhausted oil gathered on the
bottom of the exhaust silencer.
6. Maintenance
MIN
I
NSTALLATION, USE AND MAINTENANCE MANUAL –
PN130-140-155-155R
REV. 07
23-04-2015
15 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
Checking the vanes wear PN130M – PN140M – PN155-155R
• Unscrew the vanes wear check-plug on the housing.
• Turn the shaft until you see the vane.
• The vanes should slide to the bottom of the seat due to gravity:
check they really do.
Replace the vanes when their wear exceeds 10
m\m (L – L min): they may break.
Fig. 6.1
• Replace all vanes at the same time.
Checking the vanes wear PN130D – PN130HDR – PN140D –
PN140HDR
• Remove the plug and insert a metal rod ø 6 with a tapered end.
• Rest first the rod against the rotor and mark the spot.
• Afterwards turn slowly the drive shaft until the rod connects with
the vane (inserted in its slot) and mark also this spot. If the distance
between the two spots is more than 10 mm the vanes have to be
changed.
Fig. 6.2
An excessive wear of the vanes most likely will
result in the breakage of the vane itself because
the guiding function of the rotor’s slot will not be
sufficient anymore with a reduced width of the
vanes. Vanes breakage may cause serious
damages on the inside parts of the pump.
• At the end of this checking do not forget to replace the plug on the
port.
Checking the gear box oil level
• Check the level when the
pump is cooled: it must almost
reach the threaded port. Refill
if necessary.
• For a complete
replacement, 0.7 litres are
required. Use mineral oil with
EP additives for gears and
transmissions.
• When changing the oil, also replace the outlet plug washer.
Dispose of exhausted oil as provided by current
specification.
6.2. Extraordinary maintenance
• Before starting any extraordinary maintenance operation, be sure
the pump stands still and follow the safety prescriptions as described in
Cap. 3.
Adjusting the 4-way valve
• For pumps equipped with handle for manual operation or hydraulic
actuator.
• Adjust the screws to avoid the valve blocking in its seat.
Fig. 6.3
Attention: do not exceed with the adjustment:
possible vacuum loss.
• For pumps equipped with changeover valve with hydraulic
actuator: see the integrated part at the end of these instructions.
Replacing the vanes
• Remove the vacuum pump from its bearing frame and wash it
before disassembling.
• Disconnect the lubricating piping.
• Remove the screws fixing the rear flange and use the two threaded
holes to remove the flange – bearing – seal housing. If necessary, hold
the rotor by inserting a wooden block, protecting the internal bearings
from damage.
• Remove the bearing from the rear flange and replace the seal if
damaged.
REV. 0
7
23-04-2015
I
NSTALLATION, USE AND MAINTENANCE MANUAL –
PN130-140-155-155R
16 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
• Lubricate with oil the new vanes before inserting them inside each
groove of the rotor.
• Reinstall all components in the following order: rear flange, seal
ring, bearing, compensation ring, gasket and flange with lubricating
pump (we recommend the pivot-key be correctly fitted onto the shaft
groove).
Fig. 6.4
Do not damage components during assembly by
forcing them exceedingly.
• Do not flip the seal ring during
rotation of the shaft. Do not leave
foreign objects inside the pump.
Adjusting the self-lubricating pump
• The automatic lubricating pump is adjusted by the manufacturer
before the shipping.
• If consumption noticeably differs from the indicated value, adjust it
as follows:
- Remove the upper protection cover;
- Using a screwdriver and a 10 mm wrench, adjust the adjusting
screw (K). Close the nut and remount the upper protection cover;
- It is advisable to turn the screw of ¼ of turn and verify the actual
consumption.
Fig. 6.5
Do not reduce oil consumption below the value
indicated in par. 2.4 (for functioning at speeds
different from the maximum, flow is proportionate
to rotating speed).
• ½ turn of the adjusting screw causes a variation in the flow of
appr. 40 - 80 g/h, depending on using conditions.
Replacing gearbox components
• The pump with a 540 rpm gear box can be transformed into a
pump with a 1000 rpm gear box (and vice versa):
- Take down the gearbox as illustrated. Remove also the drive
shaft’s pinion;
- Install the new pinion closing the nut;
- Mount the gear wheel including bearings and seals on the front
cover, properly aligning components. This housing may now be
installed in the gear box: fit the bearing in the internal housing on
the flange;
- Properly engage gears, replace the cover’s gaskets to complete
gear replacement. Insert the parallel pin, which maintains the
correct alignment.
See Fig. 6.6.
Fig. 6.6
1100000
0
RRPPMM
55440
0
RRPPMM
I
NSTALLATION, USE AND MAINTENANCE MANUAL –
PN130-140-155-155R
REV. 07
23-04-2015
17 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
PROBLEMS
Cause Solution
• Insufficient or absent lubrication • Verify oil and rings. Check oil pump efficiency
• Low tank oil level • Fill tank with oil
• Excessive rotation speed • Reduce rpm to the prescribed working speed
• Prolonged functioning at max vacuum rate • Reduce vacuum rate
• Vacuum and/or exhaust line of insufficient diameter • Check dimensioning
Cause Solution
• Broken vanes: • Clean inner chambers, replace vanes
- due to infiltrated solids • Check the secondary shutoff and filters of the suction line
- due to insufficient lubrication • Check the oil pump
• Power transmission breakdown • Check and replace the damaged parts
• Ice inside the pump (during the cold season) • Remove ice and slowly start running it. Avoid suction of water
Cause Solution
• Four way changeover valve in idle position • Move the lever to vacuum or pressure mode end stroke
• Four way changeover valve not correctly registered • Adjust the functioning play and lubricate
• Worn vanes • Replace vanes
• The non-return valve leaks • Clean or replace if necessary
• Worn seal rings • Replace
• Tank gate valves or gaskets leak • Replace damaged or worn parts
• Tank connection pipes leak or are obstructed • Replace damaged pipes
• Obstructed primary shutoff or suction filter • Remove and clean
• Encrusted exhaust port • Remove and clean
• Vacuum line components are too small dimensioned • Verify dimensions for pump maximum performances
• Obstructed rubber couplings • Replace
Cause Solution
• Insufficient or absent lubrication • Check and adjust the lubricating pump
• Before scrapping the machine, the following materials need to be
separated and suitably disposed of:
• Hydraulic oil.
• Rubber and plastic parts, such as hoses.
• Steel and aluminium parts.
• Recycling materials allow reducing the environmental impact and
respecting the environment.
Do not dispose of in the environment. Dispose of
in compliance with the standards in force.
Unusual oil consumption
Reduced performances
The vacuum pump does not rotate
8.
Scrapping
The
vacuum pump overheats
7. Malfunctions: troubleshooting
S
PARE PART DATA SHEET –
PN130 M – PN140 M – PN155 M – PN155R M
REV. 0
7
23-04-2015
18 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
PN130
M –
PN140
M –
PN155
M –
PN155R
M
S
PARE PART DATA SHEET –
PN130 M – PN140 M – PN155 M – PN155R M
REV. 07
23-04-2015
19 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
PN 130 M
Pos.
Code Description Qty Pos.
Code Description Qty
1 1401200700 DRIP OILER
2
48 4022200113 PUMP ROTOR SEAL RING 2
2 1587009400 OIL TANK
1
49 4022200323 O RING 4850 VITON 2
3 1601607000 VANE PN130
4
50 4023100020 BEARING 6207 1
4 1605500100 COCK LEVER
1
51 4023100040 BEARING 6308 1
5 1608100000 DRIP OILER DISTRIBUTOR
1
52 4023100046 BEARING 6309 1
6 1608502500 COCK
1
53 4023250502 RUBBER BALL Ø90 1
7 1610509800 MANIFOLD SMALL FLANGE
1
54 4024251000 OIL PUMP CW ROTATION 1
8 1610512900 OIL PUMP FLANGE
1
4024251500 2 WAY – OIL PUMP LEFT 1
9 1610512800 FLANGE
1
55 4026101301 SCREW M6X10 2
10 1610512700 GEAR BOX FLANGE
1
56 4026102802 GALV. SCREW TE M8X12 3
11 1521507100 PUMP ROTOR PN130
1
57 4026102806 GALV. SCREW TE M8X20 3
12 1622002600 OIL PUMP PIVOT
1
58 4026102808 GALV. SCREW E TE M8X30 2
13 1623100500 COCK MANIFOLD
1
59 4026102908 GALV. SCREW TE M10X30 8
14 1624027500 COCK SPRING SPACER
1
60 4026121813 GALV. SCREW TCEI M10X50 2
15 1624202300 COCK REGULATING SPACER
1
61 4026121710 GALV. SCREW TCEI M12X35 2
16 1627504600 MANIFOLD PN140
1
62 4026135414 STUD SCREW M8X45 1
17 1640501200 GEAR BOX COVER
1
63 4026102807 GALV. SCREW TE M8X25 10
18 1642100200 OIL PUMP PROTECTION.
1
64 4026121304 GALV. SCREW TCEI M6X14 2
19 4029602806 DRIVE SHAFT PROTECTION
1
65 4026155503 GALV. SCREW TSPEI M 5X12 4
20 1651005500 GEAR Z 28 (540 RPM)
1
66 4026171211 SCREW M12X80 2
20a 1651010700 GEAR Z 42 (1000 RPM)
1
67 4026300025 COMPENSATION RING 2
21 1651010500 GEAR Z 70 (540 RPM)
1
68 4026308005 HEXAGONAL NUT M8 2
21a 1651010600 GEAR Z 56 (1000 RPM)
1
69 4026305508 SELFBLOCKING NUT M12 2
22 1663062900 FRONT HOUSING TUBE DIRECT LEFT
1
70 4026306115 SELFBLOCKING NUT M36X3 1
23 1663067600 REAR FLANGE SUP. TUBE
1
71 4026351504 WASHER M6 2
24 1663067700 FRONT HOUSING TUBE
1
72 4026351505 SAW-TOOTHED WASHER M8 3
25 1663062600 SUPPLY SHORT TUBE 540 LEFT
1
73 4026351506 SAW-TOOTHED WASHER M10 8
26 1663062700 SUPPLY LONG TUBE 540 LEFT
1
74 4026350508 SAW-TOOTHED WASHER M12 2
27 1663063100 TANK SUCT. TUBE 540 RIGHT
1
75 4026357007 WASHER M12 2
28 1673001000 OIL FITTING
1
76 4026359003 ALU. WASHER 21,5X26X1,5 1
29 1680609700 OIL PUMP GASKET
1
77 4026401806 CYLINDRICAL PIN 10X36 2
30 1680610500 MANIFOLD SMALL FLANGE GASKET
1
78 4026501003 KEY 12X8X40 1
31 1680614300 MANIFOLF GASKET
1
79 4026904005 PLUG G1 1/2 1
32 1680614100 GEAR BOX COVER GASKET
1
80 4026701603 GALV. PLUG G1/2 1
33 1680707300 DIRECT DRIVE FLANGE GASKET
1
81 4026702000 STRAIGHT FIRRING G1/8 - Ø4 6
34 1680707800 MANIFOLD GASKET
1
82 4026702708 COPPER WASHER 1 1/2 1
35 1681006500 PUSHING PLATE
1
83 4026706000 ELBOW FITTING G1/8 - Ø4 2
36 1681100200 DRIP OILER PLATE
1
84 4026904001 BLIND PLUG G1/2 2
37 1684000000 DISCHARGE PLUG G3/8
3
85 4026904503 OIL TANK PLUG 1
38 1685002800 WASHER 30X8.5X4
1
86 4026905002 GALV. HEXAGONAL PLUG G1/4 2
39 1685100000 ALU - WASHER
2
87 4026910103 OIL TANK FPLUG 1
40 1685100100 ALU WASHER 10X16X1,5
2
88 4026910603 HEXAGONAL CONICAL PLUG G3/8 2
41 1685100200 ALU WASHER 17X22X1,5
3
89 1685100300 ALU-WASHER 2
42 1685600200 RUBBER WASHER
2
90 4022300001 OIL PUMP SUCTION FILTER 1
43 1687510300 CORPO PN130
1
91 4026107110 SCREW TE 8.8 M8X25 10
44 1691000000 COCK SPRING
1
92 4026706003 ELBOW FITTING G1/8 – Ø6 2
45 4022106001 OIL TANK DIP STCK
1
93 1852104000 ORIENTABLE AIR CONVEYORS Ø100 2
46 4022200030 SEAL RING 41X27X10
1
47 4022200040 SEAL RING 72X40X10 1 1892005300 GASKET KIT PN130-140 1
PN 130 FL
Pos.
Code Description Qty Pos.
Code Description Qty
FL1 1627504800 FLANGED MANIFOLD 1 FL3 1852104000 SWIVEL ING CONVEYOR KIT D. 100 2
FL2 1627504900 THREADED FLANGED MANIFOLD 1 FL4 4026120406 SCREW TCEI 8X30 12
REV. 0
7
23-04-2015
S
PARE PART DATA SHEET –
PN130 M – PN140 M – PN155 M – PN155R M
20 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
PN 140 M
Pos.
Code Description Qty Pos.
Code Description Qty
1 1401200700 DRIP OILER 2 48 4022200113 PUMP ROTOR SEAL RING 2
2 1587009400 OIL TANK 1 49 4022200323 O RING 4850 VITON 2
3 1601606200 VANE PN140 4 50 4023100020 BEARING 6207 1
4 1605500100 COCK LEVER 1 51 4023100040 BEARING 6308 1
5 1608100000 DRIP OILER DISTRIBUTOR 1 52 4023100046 BEARING 6309 1
6 1608502500 COCK 1 53 4023250502 RUBBER BALL Ø90 1
7 1610509800 MANIFOLD SMALL FLANGE 1 54 4024251000 OIL PUMP CW ROTATION 1
8 1610512900 OIL PUMP FLANGE 1 4024251500 2 WAY – OIL PUMP LEFT 1
9 1610512800 FLANGE 1 55 4026101301 SCREW M6X10 2
10 1610512700 GEAR BOX FLANGE 1 56 4026102802 GALV. SCREW TE M8X12 3
11 1521503500 PUMP ROTOR PN140 1 57 4026102806 GALV. SCREW TE M8X20 3
12 1622002600 OIL PUMP PIVOT 1 58 4026102808 GALV. SCREW E TE M8X30 2
13 1623100500 COCK MANIFOLD 1 59 4026102908 GALV. SCREW TE M10X30 8
14 1624027500 COCK SPRING SPACER 1 60 4026121813 GALV. SCREW TCEI M10X50 2
15 1624202300 COCK REGULATING SPACER 1 61 4026121710 GALV. SCREW TCEI M12X35 2
16 1627504600 MANIFOLD PN140 1 62 4026135414 STUD SCREW M8X45 1
17 1640501200 GEAR BOX COVER 1 63 4026102807 GALV. SCREW TE M8X25 10
18 1642100200 OIL PUMP PROTECTION. 1 64 4026121304 GALV. SCREW TCEI M6X14 2
19 4029602806 DRIVE SHAFT PROTECTION 1 65 4026155503 GALV. SCREW TSPEI M 5X12 4
20 1651005500 GEAR Z 28 (540 RPM) 1 66 4026171211 SCREW M12X80 2
20a 1651010700 GEAR Z 42 (1000 RPM) 1 67 4026300025 COMPENSATION RING 2
21 1651010500 GEAR Z 70 (540 RPM) 1 68 4026308005 HEXAGONAL NUT M8 2
21a 1651010600 GEAR Z 56 (1000 RPM) 1 69 4026305508 SELFBLOCKING NUT M12 2
22 1663062900 FRONT HOUSING TUBE DIRECT L EFT 1 70 4026306115 SELFBLOCKING NUT M36X3 1
23 1663063000 REAR FLANGE SUPPLY TUBE LEFT 1 71 4026351504 WASHER M6 2
24 1663062800 FRONT HOUSING TUBE LEFT 1 72 4026351505 SAW-TOOTHED WASHER M8 3
25 1663062600 SUPPLY SHORT TUBE 540 LEFT 1 73 4026351506 SAW-TOOTHED WASHER M10 8
26 1663062700 SUPPLY LONG TUBE 540 LEFT 1 74 4026350508 SAW-TOOTHED WASHER M12 2
27 1663063100 TANK SUCT. TUBE RIGHT RIGHT 1 75 4026357007 WASHER M12 2
28 1673001000 OIL FITTING 1 76 4026359003 ALU. WASHER 21,5X26X1,5 1
29 1680609700 OIL PUMP GASKET 1 77 4026401806 CYLINDRICAL PIN 10X36 2
30 1680610500 MANIFOLD SMALL FLANGE GASKET 1 78 4026501003 KEY 12X8X40 1
31 1680614300 MANIFOLF GASKET 1 79 4026904005 PLUG G1 1/2 1
32 1680614100 GEAR BOX COVER GASKET 1 80 4026701603 GALV. PLUG G1/2 1
33 1680707300 DIRECT DRIVE FLANGE GASKET 1 81 4026702000 STRAIGHT FIRRING G1/8 - Ø4 6
34 1680707800 MANIFOLD GASKET 1 82 4026702708 COPPER WASHER 1 1/2 1
35 1681006500 PUSHING PLATE 1 83 4026706000 ELBOW FITTING G1/8 - Ø4 2
36 1681100200 DRIP OILER PLATE 1 84 4026904001 BLIND PLUG G1/2 2
37 1684000000 DISCHARGE PLUG G3/8 3 85 4026904503 OIL TANK PLUG 1
38 1685002800 WASHER 30X8.5X4 1 86 4026905002 GALV. HEXAGONAL PLUG G1/4 2
39 1685100000 ALU - WASHER 2 87 4026910103 OIL TANK FPLUG 1
40 1685100100 ALU WASHER 10X16X1,5 2 88 4026910603 HEXAGONAL CONICAL PLUG G3/8 2
41 1685100200 ALU WASHER 17X22X1,5 3 89 1685100300 ALU-WASHER 2
42 1685600200 RUBBER WASHER 2 90 4022300001 OIL PUMP SUCTION FILTER 1
43 1687507600 CORPO PN140 1 91 4026107110 SCREW TE M8X25 10
44 1691000000 COCK SPRING 1 92 4026706003 ELBOW FITTING G1/8 – Ø6 2
45 4022106001 OIL TANK DIP STCK 1 93 1852104000 ORIENTABLE AIR CONVEYORS Ø100 2
46 4022200030 SEAL RING 41X27X10 1
47 4022200040 SEAL RING 72X40X10 1 1892005300 GASKET KIT PN130-140 1
PN 140 FL
Pos.
Code Description Qty Pos.
Code Description Qty
FL1 1627504800 FLANGED MANIFOLD 1 FL3 1852104000 SWIVEL ING CONVEYOR KIT D. 100 2
FL2 1627504900 THREADED FLANGED MANIFOLD 1 FL4 4026120406 SCREW TCEI 8X30 12
S
PARE PART DATA SHEET –
PN130 M – PN140 M – PN155 M – PN155R M
REV. 07
23-04-2015
21 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
PN 155 M
Pos.
Code Description Qty Pos.
Code Description Qty
1 1401200700 OIL DRIPPER WITHOUT SETTING 2 48 4022200113 SEAL RING 70X55X15 VITON 2
2 1587009400 OIL TANK 1 49 4022200311 O RING 4975 VITON 2
3 16016AB6B0 VANE PN155 5 50 4023100020 BEARING 6207 1
4 1605500100 COCK HANDLE 1 51 4023100040 BEARING 6308 1
5 1608100000 DRIP OILER DISTRIBUTOR 1 52 4023100046 BEARING 6309 2
6 1608502500 4 WAY COCK 1 53 4023250502 RUBBER BALL 1
7 1610509800 MANIFOLD FLANGE 1 54 4024251000 2 WAY - OIL PUMP RIGHT 1
8 1610512900 AUT. OIL PUMP FLANGE 1 4024251500 2 WAY - OIL PUMP LEFT 1
9 161059RIB0 DIRECT DRIVE FLANGE PN155 1 55 4026101301 GALV. SCREW TE M6X10 2
10 161059TDB0 MULTIPL. 540 RPM FLANGE PN155 1 56 4026102802 GALV. SCREW TE M8X12 3
11 15215BXTB0 ROTOR PUMP PN155 1 57 4026102806 SCREW TE M8X20 10
12 1622002600 OIL PUMP DRIVE PIN 1 58 4026102808 SCREW TE M8X30 2
13 1623100500 COK CAP 1 59 4026102909 SCREW TE M10X30 22
14 1624027500 COCK SPRING SPACER 1 60 4026121813 SCREW TCEI M10X50 2
15 1624202300 COCK SETTING SPACER 1 61 4026121711 SCREW TCEI M12X40 2
16 1627504600 MANIFOLD 1 62 4026135414 STUD SCREW M8X45 1
17 164059V5B0 MULTIPL. 540 RPM COVER PN155 M 1 63 4026140309 SCREW INOX316 TE M 8X30 3
18 1642100200 REAR PROTECTION 1 64 4026141206 SCREW INOX316 TE M6X20 2
19 4029602806 CARDAN SHAFT PROTECTION 1 65 4026155505 SCREW TSPEI M5X16 4
20 1651005300 GEARE Z 25 – 540 RPM 1 66 4026171211 SCREW M12X80 2
20a 165109KFB0 GEAR Z 37 - 1000 RPM 1 67 4026300025 COMPENSATION RING LMKAS100C 2
21 165109KEB0 GEAR Z 53 - 540 RPM 1 68 4026308005 HEXAGONAL NUT M8 2
21a 165109KGB0 GEAR Z 41 - 1000 RPM 1 69 4026305508 HEXAGONAL NUT M12 2
22 16630C14B0 FRONT HOUSING TUBE DIRECT L EFT 1 70 4026306115 SELFBLOCKING NUT M36X3 1
23 16630C18B0 FRONT HOUSING TUBE 540 RPM LEFT 1 71 4026351504 SAW-TOOTHED WASHER M6 2
24 16630C19B0 TANK SUCT. TUBE 540 RIGHT/ DD RIGHT 1 72 4026351505 SAW-TOOTHED WASHER M8 30
25 1663062600 SUPPLY SHORT TUBE 540 LEFT 1 73 4026351506 SAW-TOOTHED WASHER M10 12
26 1663062700 SUPPLY LONG TUBE 540 LEFT 1 74 4026351504 GALV. SAW-TOOTHED WASHER M6 2
27 1663071RB0 REAR FLANGE SUPPLY TUBE 540 LEFT 1 75 4026357007 GALV. FLAT WASHER M12 2
28 1673001000 FILTER FITTING 1 76 4026359003 ALU. WASHER 21,5X26X1,5 3
29 1680609700 AUT. OIL PUMP GASKET 1 77 4026401806 CYLINDRICAL PIN 10X36 2
30 1680610500 MANIFOLD FLANGE GASKET 1 78 4026501004 KEY 12X8X45 1
31 1680614300 MANIFOLD GASKET 1 79 4026700911 PLUG G1 1/2 1
32 16807BCNB0 540 COVER GASKET. PN155 M 1 80 4026701603 GALV. PLUG G1/2 4
33 1680707300 DIRECT DRIVE FLANGE GASKET 1 81 4026702000 STRAIGHT FITTING. Ø 4X1/8 6
34 1680707800 CAP GASKET 1 82 4026702708 COPPER WASHER 1 1/2 1
35 1681006500 COMPENS. RING PUSHING PLATE 1 83 4026706000 FITTING 90° 4X1/8 2
36 1681100200 OIL DRIPPER SUPORTING PLATE 1 84 4026904001 BLIND PLUG G1/2 2
37 1684000000 DISCHARGE PLUG G3/8 3 85 4026904503 PLUG M20X1,5 1
38 1685002800 WASHER 30X8,5X4 1 86 4026905002 GALV. HEXAGONAL PLUG G1/4 2
39 1685100000 OIL DRIPPER ALU WASHER 2 87 4026910103 PLASTIC VENT PLUG G1 1
40 1685100100 ALU WASHER 10X16X1,5 2 88 4026910603 HEXAGONAL CONICAL PLUG G3/8 2
41 1685100200 ALU WASHER 17X22X1,5 4 89 1685100300 ALU. WASHER 1
42 1685600200 OIL TANK PLASTIC WASHER 2 90 4022300001 OIL PUMP SUCTION FILTER 1
43 16875AB9B0 PUMP HOUSING155 1 91 4026107110 SCREW TE M8X25 10
44 1691000000 COCK SPRING 1 92 4026706003 FITTING 90° 6X1/8 2
45 4022106001 VERTIC. SIGHT LEVEL 1 93 1852104000 SWIVEL ING CONVEYOR KIT D. 100 2
46 4022200030 SEAL RING 41X27X10 1
47 4022200040 SEAL RING 72X40X10 1 18920CZRB0 GASKET KIT PN155 1
PN 155 FL – PN 155R FL
Pos.
Code Description Qty Pos.
Code Description Qty
FL1 1627504800 FLANGED MANIFOLD 1 FL3 1852104000 SWIVEL ING CONVEYOR KIT D. 100 2
FL2 1627504900 THREADED FLANGED MANIFOLD 1 FL4 4026120406 SCREW TCEI 8X30 12
REV. 0
7
23-04-2015
S
PARE PART DATA SHEET –
PN130 M – PN140 M – PN155 M – PN155R M
22 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
PN 155R M (version R not available for PN130-PN140)
Pos.
Code Description Qty Pos.
Code Description Qty
R1 4026701301 BRASS FITTING 1/2X18 2 R5 1493300200 VALVE G1/2 MALE 2
R2 1663014000 FILTER HOLDER TUBE 2 R6 4022301004 SILENCER FILTER G3/4 2
R3 1681006600 TUBE HOLDER PLATE 2 R7 16016BXNB0 VANE F57 PN155 R 5
R4 4026155605 SCREW TSPEI 10.9 M6X16 4
S
PARE PART DATA SHEET –
PN130 D – PN140 D – PN155 D – PN155R D
REV. 07
23-04-2015
23 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
PN130
D –
PN140
D –
PN155
D –
PN155R
D
SPLINED SHAFT
SMOOTH
SHAFT
REV. 0
7
23-04-2015
S
PARE PART DATA SHEET –
PN130 M – PN140 M – PN155 M – PN155R M
24 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
PN 130 D – Splined shaft
Pos.
Code Description Qty Pos.
Code Description Qty
1 1401200700 OIL DRIPPER WITHOUT SETTING 2 45 4022200323 O RING 4850 VITON 2
2 1587009400 OIL TANK 1 46 4023100046 BEARING 6309 2
3 1601607000 VANE PN130 5 47 4023250502 RUBBER BALL 1
4 1605500100 COCK HANDLE 1 48 4024251000 OIL PUMP – 2 WAYS RIGHT 1
5 1608100000 OIL DRIPPER DISTRIBUTOR 1 4024251500 OIL PUMP – 2 WAYS LEFT 1
6 1608502500 4 WAY COCK 1 48A 4026414617 ELASTIC PIN 3X40 (ONLY FOR SX) 1
7 1610052800 DRIVE FLANGE PN155 D 1 49 4026101301 GALV. SCREW TE M6X10 2
8 16105BBBB0 FRONT BEARING FLANGE PN155 DIRECT 1 50 4026102704 SCREW TE M6X16 1
9 1610509800 MANIFOLD FLANGE 1 51 4026102806 SCREW TE M8X20 10
10 1610512900 AUT. OIL PUMP FLANGE 1 52 4026102807 SCREW TE M8X25 10
11 1610512800 DIRECT DRIVE FLANGE PN155 2 53 4026102808 SCREW TE M8X30 2
12 1521507100 ROTOR PN130 1 54 4026102908 SCREW TE M10X30 16
13 1622002600 OIL PUMP DRIVE PIN 1 55 4026121711 SCREW TCEI M12X40 2
14 1623100500 COCK CAP 1 56 4026135414 SCREW PEG M8X45 1
15 1624027500 COCK SPRING SPACER 1 57 4026140309 SCREW INOX 316 TE M8X30 3
16 1624202300 COCK REGUL. SPACER 1 58 4026171211 STUD SCREW M12X80 2
17 1627504600 MANIFOLD 1 59 4026300025 COMPENSATION RING LMKAS100C 1
18 1642100200 REAR PROTECTION 1 60 4026308005 HEXAG. NUT M8 2
19 16426CR1B0 CARDAN SHAFT PROTECTION 1 61 4026305508 SELF-LOCKING NUT M12 2
20 16500B6XB0 SPLINED SHAFT 1 3/8 PN155 1 62 4026306115 SELF-LOCKING NUT M36X3 1
21 1663068300 FRONT FLANGE OIL TUBE PN130 RIGHT 1 63 4026351504 SAW-TOOTHED WASHER M6 2
22 1663067600 REAR FLANGE OIL TUBE PN130 LEFT 1 64 4026351505 SAW-TOOTHED WASHER M8 25
23 1663062900 FRONT HOUSING OIL TUBE DIRECT LEFT 1 65 4026351506 SAW-TOOTHED WASHER M10 16
24 1663062600 SUPPLY SHORT TUBE 540 LEFT 1 66 4026351504 SAW-TOOTHED WASHER M6 2
25 1663062700 SUPPLY LONG TUBE 540 LEFT 1 67 4026357007 GALV. FLAT WASHER M12 2
26 1663063100 REAR FLANGE OIL TUBE M. LEFT 1 68 -
27 1663071SB0 FRONT FLANGE OIL TUBE PN HDR RIGHT 1 69 4026501003 KEY 12X8X40 1
28 1672001600 SPECIAL SCREW TCEI M10X1,5 6 70 4026700911 PLUG G1 1/2 1
29 1673001000 FILTER FITTING 1 71 4026701603 GALV. PLUG G1/2 2
30 1680609700 AUT. OIL PUMP GASKET 1 72 4026702000 STRAIGHT FITTING. Ø4XG1/8 11
31 1680610500 MANIFOLD FLANGE GASKET 1 73 4026702708 COPPER WASHER 1 1/2 1
32 1680614300 MANIFOLD GASKET 1 74 4026706000 FITTING 90° Ø4XG1/8 3
33 1680707300 FRONT FLANGE GASKET DIRECT DRIVE 2 75 4026904001 PLUG 1/2 2
34 1680707800 CAP GASKET 1 76 4026904503 PLUG M20X1,5 1
35 1681100200 OIL DRIPPER SUPPORT PLATE 1 77 4026905002 HEXAGONAL GALVANIZED PLUG G1/4 2
36 1685002800 WASHER 30X8,5X4 1 78 4026910103 PLASTIC VENT PLUG G1 1
37 1685100000 OIL DRIPPER ALU WASHER 2 79 -
38 1685600200 OIL TANK PLASTI C WASHER 2 80 4026701601 SWIVELING FITTING G1/8-Ø4 1
39 1687510300 PN130 HOUSING 1 81 1852104000 SWIVEL ING CONVEYOR KIT D. 100 2
40 1691000000 COCK SPRING 1 90 1663015XB0 SUCTION HOSE 1
41 4022106001 VERTICAL SIGHT LEVEL 1 91 16630C12B0 SHORT SUPPLY PIPE 1
42 4022200011 SEAL RING A 64X80X8 1 92 16630C13B0 DISCHARGE HOSE LONG 1
43 4022200030 SEAL RING 41X27X10 1 93 4022300001 FILTER 1
44 4022200113 SEAL RING 70X55X15 VITON 2
1892005300 GASKET KIT PN130-140 1
PN 130 D – Smooth shaft
Pos.
Code Description Qty Pos.
Code Description Qty
82 1610508200 DIRECT DRIVE FLANGE 1 86 4026102802 SCREW M8X12 3
83 1626001100 BUSHING P.D. 1 87 1521507200 ROTOR PUMP PN130 1
4 4023115057 BEARING NJ309 ECJ 1 88 4029602806 CARDAN SHAFT PROTECTION 1
85 4022200044 SEAL RING 45X65X8 1 89 4026501005 KEY 12X8X50 1
S
PARE PART DATA SHEET –
PN130 D – PN140 D – PN155 D – PN155R D
REV. 07
23-04-2015
25 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
PN 140 D – Splined shaft
Pos.
Code Description Qty Pos.
Code Description Qty
1 1401200700 OIL DRIPPER WITHOUT SETTING 2 45 4022200323 O RING 4850 VITON 2
2 1587009400 OIL TANK 1 46 4023100046 BEARING 6309 2
3 1601606200 VANE PN140 5 47 4023250502 RUBBER BALL 1
4 1605500100 COCK HANDLE 1 48 4024251000 OIL PUMP – 2 WAYS RIGHT 1
5 1608100000 OIL DRIPPER DISTRIBUTOR 1 4024251500 OIL PUMP – 2 WAYS LEFT 1
6 1608502500 4 WAY COCK 1 48A 4026414617 ELASTIC PIN 3X40 (ONLY FOR SX) 1
7 1610052800 DRIVE FLANGE PN130-140 1 49 4026101301 GALV. SCREW TE M6X10 2
8 16105BBBB0 FRONT BEARING FLANGE PN155 DIRECT 1 50 4026102704 SCREW TE M6X16 1
9 1610509800 MANIFOLD FLANGE 1 51 4026102806 SCREW TE M8X20 10
10 1610512900 AUT. OIL PUMP FLANGE 1 52 4026102807 SCREW TE M8X25 10
11 1610512800 DIRECT DRIVE FLANGE PN155 2 53 4026102808 SCREW TE M8X30 2
12 1521503500 ROTOR PN140 1 54 4026102908 SCREW TE M10X30 16
13 1622002600 OIL PUMP DRIVE PIN 1 55 4026121711 SCREW TCEI M12X40 2
14 1623100500 COCK CAP 1 56 4026135414 SCREW PEG M8X45 1
15 1624027500 COCK SPRING SPACER 1 57 4026140309 SCREW INOX 316 TE M8X30 3
16 1624202300 COCK REGUL. SPACER 1 58 4026171211 STUD SCREW M12X80 2
17 1627504600 MANIFOLD 1 59 4026300025 COMPENSATION RING LMKAS100C 1
18 1642100200 REAR PROTECTION 1 60 4026308005 HEXAG. NUT M8 2
19 16426CR1B0 CARDAN SHAFT PROTECTION 1 61 4026305508 SELF-LOCKING NUT M12 2
20 16500B6XB0 SPLINED SHAFT 1 3/8 PN155 1 62 4026306115 SELF-LOCKING NUT M36X3 1
21 1663071RB0 FRONT FLANGE-HOUSING OIL TUBE 1 63 4026351504 SAW-TOOTHED WASHER M6 2
22 1663063000 REAR FLANGE SUPPLY TUBE LEFT 1 64 4026351505 SAW-TOOTHED WASHER M8 25
23 1663062900 FRONT HOUSING TUBE LEFT 1 65 4026351506 SAW-TOOTHED WASHER M10 16
24 1663062600 SUPPLY SHORT TUBE 540 LEFT 1 66 4026351504 SAW-TOOTHED WASHER M6 2
25 1663062700 SUPPLY LONG TUBE 540 LEFT 1 67 4026357007 GALV. FLAT WASHER M12 2
26 1663063100 TANK SUCT. TUBE 540 RIGHT RIGHT 1 68 -
27 1663071SB0 HOUDING/FLANGE OIL TUBE 1 69 4026501003 KEY 12X8X40 1
28 1672001600 SPECIAL SCREW TCEI M10X1,5 6 70 4026700911 PLUG G1 1/2 1
29 1673001000 FILTER FITTING 1 71 4026701603 GALV. PLUG G1/2 2
30 1680609700 AUT. OIL PUMP GASKET 1 72 4026702000 STRAIGHT FITTING. Ø4XG1/8 11
31 1680610500 MANIFOLD FLANGE GASKET 1 73 4026702708 COPPER WASHER 1 1/2 1
32 1680614300 MANIFOLD GASKET 1 74 4026706000 FITTING 90° Ø4XG1/8 3
33 1680707300 FRONT FLANGE GASKET DIRECT DRIVE 2 75 4026904001 PLUG 1/2 2
34 1680707800 CAP GASKET 1 76 4026904503 PLUG M20X1,5 1
35 1681100200 OIL DRIPPER SUPPORT PLATE 1 77 4026905002 HEXAGONAL GALVANIZED PLUG G1/4 2
36 1685002800 WASHER 30X8,5X4 1 78 4026910103 PLASTIC VENT PLUG G1 1
37 1685100000 OIL DRIPPER ALU WASHER 2 79 -
38 1685600200 OIL TANK PLASTI C WASHER 2 80 4026701601 SWIVELING FITTING G1/8-Ø4 1
39 1687507600 PN140 HOUSING 1 81 1852104000 SWIVEL ING CONVEYOR KIT D. 100 2
40 1691000000 COCK SPRING 1 90 1663015XB0 SUCTION HOSE 1
41 4022106001 VERTICAL SIGHT LEVEL 1 91 16630C12B0 SHORT SUPPLY PIPE 1
42 4022200011 SEAL RING A 64X80X8 1 92 16630C13B0 DISCHARGE HOSE LONG 1
43 4022200030 SEAL RING 41X27X10 1 93 4022300001 FILTRE 1
44 4022200113 SEAL RING 70X55X15 VITON 2
1892005300 GASKET KIT PN130-140 1
PN 140 D – Smooth shaft
Pos.
Code Description Qty Pos.
Code Description Qty
82 1610508200 DIRECT DRIVE FLANGE 1 86 4026102802 SCREW 8.8 M8X12 3
83 1626001100 BUSHING P.D. 1 87 1521503600 ROTOR PUMP PN130 1
84 4023115057 BEARING NJ309 ECJ 1 88 4029602806 CARDAN SHAFT PROTECTION 1
85 4022200044 SEAL RING 45X65X8 1 89 4026501003 KEY 12X8X50 1
REV. 0
7
23-04-2015
S
PARE PART DATA SHEET –
PN130 M – PN140 M – PN155 M – PN155R M
26 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
PN 155 D – Splined shaft
Pos.
Code Description Qty Pos.
Code Description Qty
1 1401200700 OIL DRIPPER WITHOUT SETTING 2 45 4022200311 O RING 4975 VITON 2
2 1587009400 OIL TANK 1 46 4023100046 BEARING 6309 2
3 16016AB6B0 VANE PN155 5 47 4023250502 RUBBER BALL 1
4 1605500100 COCK HANDLE 1 48 4024251000 OIL PUMP – 2 WAYS RIGHT 1
5 1608100000 OIL DRIPPER DISTRIBUTOR 1 4024251500 OIL PUMP – 2 WAYS LEFT 1
6 1608502500 4 WAY COCK 1 48A 4026414617 ELASTIC PIN 3X40 (ONLY FOR SX) 1
7 16100B6PB0 DRIVE FLANGE PN155 D 1 49 4026101301 GALV. SCREW TE M6X10 2
8 16105BBBB0 FRONT BEARING FLANGE PN155 DIRECT 1 50 4026102704 SCREW TE M6X16 1
9 1610509800 MANIFOLD FLANGE 1 51 4026102806 SCREW TE M8X20 10
10 1610512900 AUT. OIL PUMP FLANGE 1 52 4026102807 SCREW TE M8X25 10
11 161059RIB0 DIRECT DRIVE FLANGE PN155 2 53 4026102808 SCREW TE M8X30 2
12 15215BXTB0 ROTOR PN155 1 54 4026102908 SCREW TE M10X30 16
13 1622002600 OIL PUMP DRIVE PIN 1 55 4026121711 SCREW TCEI M12X40 2
14 1623100500 COCK CAP 1 56 4026135414 SCREW PEG M8X45 1
15 1624027500 COCK SPRING SPACER 1 57 4026140309 SCREW INOX 316 TE M8X30 3
16 1624202300 COCK REGUL. SPACER 1 58 4026171211 STUD SCREW M12X80 2
17 1627504600 MANIFOLD 1 59 4026300025 COMPENSATION RING LMKAS100C 1
18 1642100200 REAR PROTECTION 1 60 4026308005 HEXAG. NUT M8 2
19 16426CR1B0 CARDAN SHAFT PROTECTION 1 61 4026305508 SELF-LOCKING NUT M12 2
20 16500B6XB0 SPLINED SHAFT 1 3/8 PN155 1 62 4026306115 SELF-LOCKING NUT M36X3 1
21 1663071RB0 FRONT FLANGE OIL TUBE PN HDR RIGHT 1 63 4026351504 SAW-TOOTHED WASHER M6 2
22 1663063000 REAR FLANGE OIL TUBE M. LEFT 1 64 4026351505 SAW-TOOTHED WASHER M8 25
23 16630C14B0 FRONT HOUSING OIL TUBE 1 65 4026351506 SAW-TOOTHED WASHER M10 16
24 1663062600 SUPPLY SHORT OIL TUBE DIRECT LEFT 1 66 4026351504 SAW-TOOTHED WASHER M6 2
25 1663062700 SUPPLY LONG OIL TUBE DIRECT LEFT 1 67 4026357007 GALV. FLAT WASHER M12 2
26 16630C19B0 SUCTION TANK OIL TUBE DIRECT LEFT 1 68 4026359003 ALU WASHER 21,5X26X1,5 4
27 16630C15B0 FRONT FLANGE-HOUSING OIL TUBE RIG. 1 69 4026501005 KEY 12X8X50 1
28 1672001600 SPECIAL SCREW TCEI M10X1,5 6 70 4026700911 PLUG G1 1/2 1
29 1673001000 FILTER FITTING 1 71 4026701603 GALV. PLUG G1/2 2
30 1680609700 AUT. OIL PUMP GASKET 1 72 4026702000 STRAIGHT FITTING. Ø4XG1/8 11
31 1680610500 MANIFOLD FLANGE GASKET 1 73 4026702708 COPPER WASHER 1 1/2 1
32 1680614300 MANIFOLD GASKET 1 74 4026706000 FITTING 90° Ø4XG1/8 3
33 1680707300 FRONT FLANGE GASKET DIRECT DRIVE 2 75 4026904001 PLUG 1/2 2
34 1680707800 CAP GASKET 1 76 4026904503 PLUG M20X1,5 1
35 1681006800 COCK PLATE CAP 1 77 4026905002 HEXAGONAL GALVANIZED PLUG G1/4 2
36 1681100200 OIL DRIPPER SUPPORT PLATE 1 78 4026910103 PLASTIC VENT PLUG G1 1
37 1685100000 OIL DRIPPER ALU WASHER 2 79 4026910603 HEXAGONAL CONICAL PLUG G3/8 2
38 1685600200 OIL TANK PLASTI C WASHER 2 80 4026701601 SWIVELING FITTING G1/8-Ø4 1
39 16875AB9B0 PN155 HOUSING 1 81 1852104000 SWIVEL ING CONVEYOR KIT D. 100 2
40 1691000000 COCK SPRING 1 90 16630C16B0 SUCTION HOSE 1
41 4022106001 VERTICAL SIGHT LEVEL 1 91 16630C12B0 SHORT SUPPLY PIPE 1
42 4022200011 SEAL RING A 64X80X8 1 92 16630C13B0 DISCHARGE HOSE LONG 1
43 4022200030 SEAL RING 41X27X10 1 93 4022300001 FILTRE 1
44 4022200113 SEAL RING 70X55X15 VITON 2
18920CZQB0 JOINT KIT PN155 1
PN 155 D – Smooth shaft
Pos.
Code Description Qty Pos.
Code Description Qty
82 1610508200 DIRECT DRIVE FLANGE 1 86 4026102802 SCREW M8X12 3
83 1626001100 BUSHING P.D. 1 87 15215BXUB0 ROTORE PUMP PN155 1
84 4023115057 BEARING NJ309 ECJ 1 88 4029602806 CARDAN SHAFT PROTECTION 1
85 4022200044 SEAL RING 45X65X8 1 89 4026501005 KEY 12X8X50 1
S
PARE PART DATA SHEET –
PN130 D – PN140 D – PN155 D – PN155R D
REV. 07
23-04-2015
27 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
PN 155R D – Smooth shaft – Splined shaft
Pos.
Code Description Qty Pos.
Code Description Qty
R1 4026701301 COPPER FITTING 1/2X18 2 R5 1493300200 VALVE G1/2 MALE 2
R2 1663014000 FILTER SUPPORT 2 R6 4022301004 SILENCER FILTER G3/4 2
R3 1681006600 PLATE FERMATUBO 2 R7 16016BXNB0 VANE F57 PN155R 5
R4 4026155605 SCREW TSPEI M6X16 4
REV. 0
7
23-04-2015
S
PARE PART DATA SHEET –
PN130 HDR – PN140 HDR – PN155 HDR
28 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
PN 130 HDR
Pos.
Code Description Qty Pos.
Code Description Qty
1 4023100046 BEARING 6309 1 14 4026350910 SAW-TOOTHED WASHER M10 8
2 1680707300 GASKET 1 15 1510512800 FLANGE PN140 1
3 4026107211 SCREW M10X30 8 16 1521507200 ROTOR PN 130 HDR 1
4 4022200044 SEAL RING 65X45X8 1 17 4026350909 SAW-TOOTHED WASHER M8 3
5 4026904003 PLUG ½ G 1 18 4026120403 SCREW TCEI M8X20 3
6 1470102300 JOINT HDR PN140 1 19 4026351505 SAW-TOOTHED WASHER M8 2
7 1610021600 HDR TRASMISSION FLANGE 1 20 4026120403 SCREW M8X20 2
8 4026103004 SCREW M8X80 2 21 1626001100 DIRECT DRIVE BUSHING 1
9 1612501000 HDR TRASMISSION HOUSING 1 22 -
10 4026305508 NUT M12 SELF LOCKING 2 23 -
11 4024107001 HYDRAULIC MOTOR FM 40.73 1 24 4026300025 COMPENSATING RING 2
12 4026171304 SCREW M14X40 4 25 4026359001 WASHER ALUMINUM 40X33.5X1.5 1
13 4026308008 NUT M14 4 26 4022200113 SEAL RING 70X55X15 VITON 1
PN130
HDR
–
PN140
HDR
–
PN155
HDR
–
PN155R
HDR
S
PARE PART DATA SHEET –
PN130 HDR – PN140 HDR – PN155 HDR
REV. 07
23-04-2015
29 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
PN 140 HDR
Pos.
Code Description Qty Pos.
Code Description Qty
1 4023100046 BEARING 6309 1 14 4026350910 SAW-TOOTHED WASHER M10 8
2 1680707300 GASKET 1 15 1510512800 FLANGE PN140 1
3 4026107211 SCREW M10X30 8 16 1521503600 ROTOR PN 140 HDR 1
4 4022200044 SEAL RING 65X45X8 1 17 4026350909 SAW-TOOTHED WASHER M8 3
5 4026904003 PLUG ½ G 1 18 4026120403 SCREW TCEI M8X20 3
6 1470102300 JOINT HDR PN 140 1 19 4026351505 SAW-TOOTHED WASHER M8 2
7 1610021600 HDR TRASMISSION FLANGE 1 20 4026120403 SCREW M8X20 2
8 4026103004 SCREW M8X80 2 21 1626001100 DIRECT DRIVE BUSHING 1
9 1612501000 HDR TRASMISSION HOUSING 1 22 -
10 4026305508 NUT M12 SELF LOCKING 2 23 -
11 4024107001 HYDRAULIC MOTOR FM 40.73 1 24 4026300025 ANELLO DI COMPENSAZIONE LMKAS100C 2
12 4026171304 SCREW M14X40 4 25 4026359001 RONDELLA 40X33.5X1.5 ALLUMINIO 1
13 4026308008 NUT M14 4 26 4022200113 SEAL RING 70X55X15 VITON 1
PN 155 HDR – PN155R HDR
Pos.
Code Description Qty Pos.
Code Description Qty
1 4023100046 BEARING 6309 1 14 4026350910 SAW-TOOTHED WASHER M10 8
2 1680707300 GASKET 1 15 161059RIB0 FLANGE PN140 1
3 4026107211 SCREW M 10X30 8 16 15215BXUB0 ROTOR PN155 HDR 1
4 4022200044 SEAL RING 65X45X8 1 17 4026350909 SAW-TOOTHED WASHER M8 3
5 4026904003 PLUG ½ G 1 18 4026120403 SCREW TCEI M8X20 3
6 14701BEBB0 JOINT HDR PN 140 1 19 4026351505 SAW-TOOTHED WASHER M8 2
7 1610021600 HDR TRASMISSION FLANGE 1 20 4026120403 SCREW M8X20 2
8 4026171211 SCREW M8X80 2 21 1626001100 DIRECT DRIVE BUSHING 1
9 1612501000 HDR TRASMISSION HOUSING 1 22 4026359003 WASHER ALUMINUM 21,5X26X1,5 3
10 4026305508 NUT M12 SELF LOCKING 2 23 4026701603 PLUGG1/2 4
11 4024107004 HYDRAULIC MOTOR FM 40.73 1 24 4026300025 COMPENSATING RING 2
12 4026171304 SCREW M14X40 4 25 4026359001 WASHER ALUMINUM 40X33.5X1.5 1
13 4026308008 NUT M14 4 26 4022200113 SEAL RING 70X55X15 VITON 1
REV. 0
7
23-04-2015
S
PARE PART DATA SHEET –
PN155 SP – PN155R SP
30 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
Pos.
Code Description Qty Pos.
Code Description Qty
LUBRICATION DIRECT DRIVE L UBRICATION M540-M1000 SX
1 1612034000 OIL TANK SUPPORT 1 1 1612034000 OIL TANK SUPPORT 1
2 1624042800 SPACER 2 2 1624042800 SPACER 2
3 16630C14B0 OIL PIPE 1 3 16630C14B0 OIL PIPE 1
4 16630C15B0 OIL PIPE 1 4 1663067000 OIL PIPE 1
5 1663067000 OIL PIPE 1 5 1663067800 OIL PIPE 1
6 1663067800 OIL PIPE 1 6 1663067900 OIL PIPE 1
7 1663067900 OIL PIPE 1 7 1663068000 OIL PIPE 1
8 1663068000 OIL PIPE 1 8 1663068200 OIL PIPE 1
9 1663068100 OIL PIPE 1 9 1687600000 OIL TANK 1
10 1687600000 OIL TANK 1 10 4026103013 SCREW M12X90 2
11 4026103013 SCREW M12X90 2 11 4026121708 SCREW M12X25 2
12 4026121708 SCREW M12X25 2 12 4026305508 NUT M12 2
13 4026305508 NUT M12 2 13 4026350508 GROWER M12 2
14 4026350508 GROWER M12 2 14 4026357007 WASHER PIANA M12 2
15 4026357007 WASHER M12 2 15 1612033900 SUPPORT OILERS 1
16 1612033900 SUPPORT OILERS 1
PN155
–
PN155R
SP (REAR TANK
)
PN155
-
PN155R SP PD SX
PN155
– PN155R SP
M540 - M1000 SX
S
PARE PART DATA SHEET – 4-WAY VALVE WITH HYDRAULIC ACTUATOR
REV. 07
23-04-2015
31 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
Actuator HDR PN130 – PN140 – PN155
Pos.
Code Description Q.ty Pos.
Code Description Q.ty
1 143027T6B0 HDR ACTUATOR CYLINDER 1 13 168509U0B0 HDR ACTUATOR WASHER 1
2 15020A10B0 LEVA ATTUATORE HDR PN140 – PN155 1 14 1691000000 SPIRING COCK 1
3 151307TJB0 COCK-HDR ACTUATOR BRACKET 1 15 4022100100 STRAIGHT GREASE DISPENSER M6X1 1
4 1608502900 ACTUATOR COCK 1 16 4022100107 STRAIGHT GREASE DISPENSER M10X1 1
5 1623100700 COCK CAP 1 17 4022200030 SEAL RING 41X27X10 1
6 1624027500 SPIRING SPACER 1 18 4026121405 SCREW TCEI M8X20 2
7 1624043400 HDR ACTUATOR LEVER SPACER 4 19 4026121408 SCREW TCEI M8X35 4
8 1624202300 COCK FITTING SPACER 1 20 4026135414 STUD SCREW M8X45 1
9 164206XYB0 HDR ACTUATOR PROTECTION 1 21 4026155705 SCREW M8X16 1
10 1673009700 GREASE DISPENSER CONNECTION 1 22 4026308005 NUT M8 4
11 1680707800 CAP GASKET 1 23 4026350505 WASHER GROWER M8 6
12 1685002800 WASHER 30X8,5X4 1 24 4026510012 SEEGER RING 14 1
A
CTUATOR
HDR
PN130
–
PN140
–
PN155
REV. 0
7
23-04-2015
S
PARE PART DATA SHEET – 4-WAY VALVE WITH PNEUMATIC ACTUATOR
32 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
Pneumatic actuator PN130 – PN140 – PN155
Pos.
Code Description Qty Pos.
Code Description Qty
1 160858KBB0 PNEUMATIC ACTUATOR SUPPORT 1 10 4022200005 SEAL RING 37X27X7 1
2 161258H0B0 PNEUMATIC ACTUATOR FLANGE 1 11 4022200330 OR 3375 1
3 1640580QB0 PNEUMATIC ACTUATOR NUT 1 12 4022200331 OR 2137 1
4 167007ZAB0 GASKET 1 13 4026102804 SCREW TE M8X16 4
5 1680707800 ACTUATOR COCK RING-NUT 1 14 4026102807 SCREW TE M8X25 4
6 168409PQB0 SPACER PNEUMATIC ACTUATOR 1 15 4026121407 SCREW TCEI M8X25 4
7 168529TFB0 SPRING 1 16 4026350505 WASHER GROWER M8 4
8 1691000200 STRAIGHT GREASE DISPENSER M6X1 1 17 4026351505 WASHER M 8 8
9 4022100100 INGRASSATORE SFERICO DIR.M6X1 1 18 4027100405 PNEUMATIC ACTUATOR 1
P
NEUMATIC ACTUATOR
PN130
–
PN140
–
PN155
REV. 07
23-04-2015
I
NTEGRATION 1 - ADJUSTING THE 4-WAY VALVE WITH PNM ACTUATOR
33 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
• If the adjustment of the 4-way valve position to the manifold seat is
needed (due to coupling with an exceeding interference causing
difficult or incomplete rotation – or – coupling with an exceeding play
causing reduced performances in the vacuum pump), follow the
instructions below.
• Unscrew the 4 screws M8x16 which fix the upper cover to the
inferior part fastened to the 4-way valve.
• Clean it from the inner lubricant. “Mar” the initial position of the
valve as indicated with the broken line by aligning the square to a
couple of holes on the mounting.
• With a 36 spanner, loosen the nut above by holding the valve firm
with a 17mm spanner.
• The valve can now be vertically lifted.
• Adjust the 4-way valve by turning the ring nut with a hook spanner
(or other tool) while keeping the valve firm with a 17mm spanner.
• Turning the nut to the right, the valve lifts, turning it to the left, it
lowers; each notch is equal to a 0,25 mm shifting of the valve.
• Fasten the nut with a 36mm spanner while keeping the valve firm
with the 17mm spanner.
• Turn the valve checking it does not oppose excessive resistance.
Do not exceed in lifting the deviator: it may not
grant a perfect seal and cause a possible vacuum
loss.
• Lubricate the area around the nut to grant that those parts subject
to wear are lubricated.
Instead using the hook spanner, the nut can be fastened and the
valve turned to lift it or lower it from its seat as follows.
• Fasten the nut by slightly screwing a M6 screw in the threaded
hole (A).
• Turn the valve (1/4 – 1/8 turn) by pushing upon the shank with the
17mm fixed spanner. Then, fasten the lock nut with the 36mm spanner.
• Remove the M6 screw previously screwed.
INTEGRATION 1 - ADJUSTING THE
4
-
WAY VALVE WITH PNM ACTUATOR
A
REV. 0
7
23-04-2015
I
NTEGRATION 1 - ADJUSTING THE 4-WAY VALVE WITH PNM ACTUATOR
34 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
Place the 4-way valve as marked before the
disassembly.
• Mount the upper cover back fastening it with 4 M8 screw and
make sure the OR-ring does not get lost.
REV. 07
23-04-2015
35 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
REV. 0
7
23-04-2015
I
NTEGRATION 1 - ADJUSTING THE 4-WAY VALVE WITH PNM ACTUATOR
36 / 36
Jurop
SpA
Via Crosera n° 50
33082 Azzano Decimo, PN (Italia)
TEL. +39 0
434 636811
FAX.
+39 0
434 636812
http://www.jurop.it
e-mail: info@jurop.it
Model Issue date Revision No. Revision date Filled out by Viewed by
PN130-140-155-155R 14-07-2011 07 23-04-2015 U.T. A.T.
Jurop SpA
Via Crosera, 50
33082 Azzano Decimo, PN (Italy)
Tel. +39 0434 636811
Fax. +39 0434 636812
http://www.jurop.it
e-mail: info@jurop.it
Jurop SpA reserves the right to modify the products described in this manual without prior notice.
Loading...