Page 1
IMPRESSA F70 / F707
Instructions for use
Page 2
Legend:
䡲 DISPLAY: serves as information.
䡲 DISPLAY: please follow the instructions shown.
= Note = Important = Tip
Page 3
Fig. 1 Fig. 2 Fig. 3 Fig. 4
Fig. 6 Fig. 7 Fig. 9 Fig. 10
Fig. 11 Fig. 12 Fig. 13 Fig. 14
Fig. 16
Fig. 5
Fig. 8
Fig. 15
Fig. 17 Fig. 18
Page 4
Temp. max.
Fig. 19
Fig. 21
Fig. 20
Temp. min.
Page 5
Control elements
1. Rotary Switch
2. Illuminated ring
3. ON / OFF symbol
4. 1 LARGE CUP symbol
5. 1 COFFEE symbol
6. 1 ESPRESSO symbol
7. MAINTENANCE symbol
8. START symbol
9. Display dialog system
10. Water tank with handle
11. Filler funnel for pre-ground coffee
12. Bean tank cover
13. Aroma preservation cover
14. Steam / hot water draw-off tap
15. Profi-Auto-Cappuccino Frother with milk pipe
16. Interchangeable hot water nozzle (see Fig. 5)
17. Height-adjustable coffee spout
18. Coffee grounds container
19. Drip grate
20. Drip tray
21. MILD symbol
22. NORMAL symbol
23. STRONG symbol
24. Power switch
10
9
13
14
17
18
11
1
2
12
20
15/16
19
24
3
9
7
4
56
8212223
Page 6
6
Contents
1. Safety information ..............................................page 7
1.1 Warning
.....................................................page 7
1.2 Precautions
.................................................page 7
2. Preparing the IMPRESSA
.......................................page 7
2.1 Check supply voltage
.....................................page 7
2.2 Check electrical fuse
......................................page 7
2.3 Fill water tank
..............................................page 8
2.4 Fill coffee beans
...........................................page 8
2.5 Adjusting the grinding gear
.............................page 8
2.6 Power switch
...............................................page 8
3. First use
...........................................................page 8
4. Adjusting the water hardness
.................................page 9
5. Installation of CLARIS plus filter cartridges
..................page 10
5.1 Installing the filter
.........................................page 10
5.2 Replacing the filter
........................................page 11
5.3 Changing the filter without display request
..........page 11
6. Rinsing the IMPRESSA
..........................................page 11
6.1 Rinsing the IMPRESSA without display request
......page 12
7. Adjusting the water quantity for coffee
.....................page 12
8. Making 1 cup of coffee
.........................................page 12
9. Making 2 cups of coffee
........................................page 13
10. Drawing off pre-ground coffee
................................page 13
11. Drawing off hot water
..........................................page 14
12. Dispensing steam
...............................................page 14
13. Dispensing Cappuccino with the Professional
Cappuccino Frother
.............................................page 15
13.1 Dispensing Hot Milk with the
Professional Cappuccino Frother
.......................page 16
13.2 Cleaning of the Professional Cappuccino Frother
...page 16
13.3 Rinsing the Professional Cappuccino Frother
........page 16
13.4 Cleaning the Professional Cappuccino Frother
......page 17
14. Switching off the IMPRESSA
...................................page 17
15. Programming
....................................................page 18
15.1 Programming the filter
...................................page 18
15.2 Programming the water hardness......................page 18
15.3 Maintenance menu
.......................................page 18
15.4 Programming the aroma INTENSIVE
or STANDARD
..............................................page 18
15.5 Programming the temperature
.........................page 19
15.6 Programming the time
...................................page 19
15.7 Programming the automatic switch-on time
........page 20
15.8 Programming the automatic switch-off time
........page 20
15.9 Cup counter
................................................page 21
15.10 Programming the language
.............................page 21
15.11 Programming Display 24H/AM/PM
.....................page 22
15.12 Programming the display for ML/OZ
..................page 22
15.13 Exit programming mode
.................................page 22
16. Maintenance
......................................................page 23
16.1 Filling in water
.............................................page 23
16.2 Emptying the coffee grounds container
..............page 23
16.3 Drip tray missing
..........................................page 23
16.4 Fill coffee beans
...........................................page 23
16.5 Replacing the filter
........................................page 23
16.6 Cleaning the IMPRESSA
..................................page 24
16.7 IMPRESSA calcified
........................................page 24
16.8 General cleaning instructions
...........................page 24
16.9 Emptying the system
.....................................page 24
17. Cleaning
...........................................................page 25
17.1 Cleaning without display request
......................page 25
18. Descaling
..........................................................page 26
18.1 Decalcifying without display request
..................page 27
19. Disposal
...........................................................page 27
20. Tips for perfect coffee
..........................................page 28
21. Messages
..........................................................page 29
22. Problems
..........................................................page 30
23. Legal information
................................................page 31
24. Technical data
....................................................page 31
Page 7
7
Introduction
Thank you for purchasing the IMPRESSA. To ensure perfect functioning of your IMPRESSA, carefully read this operating manual and keep
it for future reference.
Should you need more information or if you encounter particular
problems not specified in these operating instructions in sufficient
detail, either contact us directly or contact your local authorized
dealer.
You will also find useful tips on operation and maintenance of
your IMPRESSA on our website at www.jura.com.
1. Safety information
1.1 Warning
䡲 Children do not realize the dangers involved in using electric
appliances, for this reason always keep an eye on children when
they use electric appliances.
䡲 The coffee machine may only be used by instructed persons.
䡲 Never use a defective coffee machine or a machine with a defective
mains cable.
䡲 Never repair or open the coffee machine yourself. Any repairs may
only be carried out by authorized service shops using ori ginal spare
parts and accessories.
䡲 Never immerse the coffee machine in water.
1.2 Precautions
䡲 Never expose the coffee machine to weather (rain, snow, frost),
never touch the machine when your hands are wet.
䡲 Place the IMPRESSA on a firm, level base that is resistant to any
water that may leak. Never stand on hot or warm surfaces (oven
hobs). Keep out of the reach of children.
䡲 If you don’t use the machine for a longer time (holidays, etc.)
always disconnect the mains cable.
䡲 Always disconnect mains cable before cleaning the machine.
䡲 When disconnecting the mains cable never pull on the mains cable
or the machine itself.
䡲 The coffee machine is connected to mains supply via a mains cable.
Make sure nobody can trip over the mains cable. Make sure
children and pets cannot reach the machine
䡲 Never put the coffee machine or individual parts of it into a dish-
washer.
䡲 Make sure to install the machine at a place with sufficient air circu-
lation, to prevent overheating of the machine.
2. Preparing the IMPRESSA
2.1 Check supply voltage
The IMPRESSA is preset in the factory to the correct mains voltage.
Check if your local mains supply voltage complies with the infor mation given on the type plate on the underside of the IMPRESSA.
2.2 Check electrical fuse
The IMPRESSA is designed for an electric current of 10 amperes. Check
if the electrical fuse has sufficient capacity.
E
Page 8
8
2.3 Fill water tank
Only use fresh, cold water. Never fill in milk, mineral water or
other liquids.
䡲 Remove the water tank and rinse it with cold tap water thoroughly
(Fig. 4).
䡲 Then fill the water tank and reinstall it. Make sure to install the tank
properly, it must engage audibly.
2.4 Fill coffee beans
To ensure that your machine will work perfectly for a long time
and to avoid damage, please note that the grinding gear of
your JURA coffee machine is not suitable for coffee beans which
were treated, during or after roasting, with additives (e.g.
sugar). Such coffee blends may damage the grinding gear. Any
repair costs resulting from the use of such blends are not
covered by warranty.
䡲 Open the bean tank cover (12) and remove the aroma preservation
cover (13).
䡲 Remove any dirt or foreign matter from the bean tank.
䡲 Fill coffee beans in the bean tank and close the cover.
2.5 Adjusting the grinding gear
You can adjust the grinding gear to the roast of your coffee. We recommend
a fine grinding degree 씮 for bright roasts (the smaller the dots,
the finer the grinding)
a coarse degree 씮 for dark roasts (the larger the dots, the
coarser the grinding)
The grinding degree may only be adjusted while the grinding
gear is running.
䡲 Open the bean tank cover (12) and remove the aroma preservation
cover (13).
䡲 To adjust the grinding degree, turn the Rotary Switch (Fig. 2) to the
required position.
2.6 Power switch
Actuate the power switch (24) on your IMPRESSA before using
the machine for the first time.
We recommend that you switch off your IMPRESSA with the
power switch (24) if you intend not to use the machine for
longer periods of time (e.g.during holidays).
3. First use
䡲 Fill coffee beans in the bean tank (12).
䡲 Switch on the IMPRESSA using the power switch (24).
䡲
Your IMPRESSA is in standby mode.
䡲 Touch the (3) symbol
䡲 SPRACHE
DEUTSCH
䡲 The illuminated ring (2) is active.
䡲 Turn the Rotary Switch (1) until the required language is dis played
(Fig. 17).
䡲 For example LANGUAGE
ENGLISH
Page 9
9
E
䡲 Confirm your selection by pressing the Rotary Switch (1) (Fig. 17).
䡲 FILL
WATER
䡲 Fill the water tank (10) with fresh water.
䡲 OPEN TAP
䡲 Place a receptacle under the Professional Cappuccino Frother (15)
(Fig. 10).
䡲 Open the steam / hot water draw-off tap (14) (Fig. 12).
䡲 FILLING
SYSTEM
䡲 CLOSE TAP
䡲 Close the steam / hot water draw-off tap (14).
䡲 FILLING SYSTEM
䡲 HEATING
䡲 PRESS
MAINT.
䡲 Touch the symbol (7).
䡲 Machine carries out a rinsing operation.
䡲 RINSING
䡲 READY
If BEANS FILL is displayed, press the coffee draw-off key again.
Machine not filled with coffee beans yet.
To get an excellent crema, adjust the coffee spout (17) to the
size of your cup (Fig. 3).
4. Adjusting the water hardness
Water is heated in the IMPRESSA. As a result, calcification occurs during normal use and is indicated auto matically. Before
using the IMPRESSA for the first time the hardness of the water
used must be adjusted. Use the supplied test sticks for this.
1° German hardness is equivalent to 1.79° French hardness.
If the filter is activated, the program step Water Hardness no
longer appears.
The IMPRESSA has 5 hardness degrees which can be used and
are displayed while you are adjusting the water hardness.
The displayed information means the following:
LEVEL –– Water hardness function switched off
LEVEL 1 German water hardness degree 1 to 7°
French Water hardness degree 1.79 – 12.53°
LEVEL 2 German water hardness degree 8 to 15°
French Water hardness degree 14.32 – 26.85°
LEVEL 3 German water hardness degree 16 to 23°
French Water hardness degree 28.64 – 41.14°
LEVEL 4 German water hardness degree 24 to 30°
French Water hardness degree 42.96 – 53.7°
When the IMPRESSA leaves the factory it is adjusted to LEVEL 3. You
can adjust another hardness. To do this, proceed as follows:
䡲 READY
䡲 Press the Rotary Switch (1) until
FILTER –/⻫ appears
Page 10
10
䡲 FILTER –
䡲 Turn the Rotary Switch (1) until the following message is displayed:
䡲 HARDNESS
䡲 Now press the Rotary Switch (1) to start the programming.
䡲 LEVEL 3
䡲 Turn the Rotary Switch (1) until the required level is displayed.
䡲 For example, LEVEL 4
䡲 Press the Rotary Switch (1) to confirm the required level.
䡲 HARDNESS
䡲 Turn the Rotary Switch (1) until
EXIT appears
䡲 Press the Rotary Switch (1) to leave the programming mode.
䡲 READY
5. Installation of CLARIS plus filter cartridges
If the CLARIS plus filter cartridge is installed properly, descaling
of the coffee machine is no longer required. For more infor mation on the CLARIS plus filter cartridge refer to brochure
‘CLARIS plus. Hard on limescale. Gentle on your coffee
machine.’
5.1 Installing the filter
Draw off 1/2 litre of water to rinse filter completely. In order to
ensure perfect operation, close tap (14) only after the display
says
CLOSE TAP
䡲 Fold up the cartridge holder. Install the filter cartridge in the water
tank, applying a gentle pressure (Fig. 1).
䡲 Fold down the cartridge holder again until it engages audibly.
䡲 Fill the water tank with cold, fresh tap water and install it again.
䡲 Press the Rotary Switch (1) until
FILTER –/⻫ appears
䡲 FILTER –
䡲 Press the Rotary Switch (1) to start the programming.
䡲 NO –
䡲 Turn the Rotary Switch (1) until the following message is displayed:
䡲 YES ⻫
䡲 Press the Rotary Switch (1) to activate the filter cartridge.
䡲 INSERT
OPEN TAP
䡲 Put a sufficiently large container (at least 0.5 litre) under the Pro-
fessional Cappuccino Frother (15) (Fig. 10).
䡲 Turn the selector switch of the Professional Cappuccino Frother (15)
to the steam position (Fig. 20).
䡲 If not installed already, insert the CLARIS plus filter.
䡲 Open the steam / hot water draw-off tap (14) (Fig.12).
䡲 RINSING
FILTER
䡲 CLOSE TAP
䡲 Close the steam/hot water draw-off tap (14), now the IM PRESSA will
heat up to coffee temperature.
Page 11
11
E
䡲 HEATING UP
䡲 READY
Now you have activated the filter. In Programming Mode the
water hardness selection function is no longer displayed.
5.2 Replacing the filter
Draw off 1/2 litre of water to rinse filter completely. In order to
ensure perfect operation, close tap (14) only after the display
says
CLOSE TAP
After drawing off approx. 50 litres, the filter cart ridge will be
used up. A message requesting you to replace the filter will
appear on the display. The scale on the cartridge holder in the
water tank will tell you how much longer you can use the
CLARIS plus filters.
䡲 CHANGE FILTER / MACHINE READY
䡲 Touch the symbol (7).
䡲 REPLACE
OPEN TAP
䡲 Remove the water tank from the machine and empty it.
䡲 Fold up the cartridge holder. Install the filter cartridge in the water
tank, applying a gentle pressure (Fig. 1).
䡲 Fold down the cartridge holder again until it engages audibly.
䡲 Fill the water tank with cold, fresh tap water and reinstall it.
䡲 Place a sufficiently large receptacle (at least 1/2 litre) under the
Professional Cappuccino Frother (15) (Fig. 10).
䡲 Turn the selector switch of the Professional Cappuccino Frother (15)
to the steam position (Fig. 20).
䡲 Open the tap for dispensing steam/hot water (14) (Fig. 12).
䡲 RINSING
FILTER
䡲 CLOSE TAP
䡲 Open the steam / hot water draw-off tap (14) (Fig. 12).
䡲 HEATING UP
䡲 READY
5.3 Changing the filter without display request
䡲 Press the Rotary Switch (1) until
FILTER ⻫ appears.
䡲 Press the Rotary Switch (1) to confirm.
䡲 YES ⻫
䡲 Press the Rotary Switch (1) again to confirm.
䡲 INSERT/OPEN TAP
䡲 The program ‘Change filter’ is now active. Now proceed as
described in Chapter 5.2 from REPLACE/OPEN TAP
onwards.
6. Rinsing the IMPRESSA
When the IMPRESSA is switched off and has cooled down, a
rinsing operation is started when the machine is switched on
again. When the machine is switched off, a rinsing operation is
started automatically.
Page 12
12
You can adjust the water quantity in steps of 5 ML using the Rotary
Switch (1).
䡲 READY
䡲 Turn the Rotary Switch (1) until the required water quantity is
displayed.
䡲 For example, 120 ML
8. Making 1 cup of coffee
You can choose from 3 different coffee strengths. Touch one of
the symbols / / to select the strength of your coffee.
MILD NORMAL STRONG.
You can set the amount of water you want with the Rotary
Switch (1) prior to drawing off coffee
Touch the (8) symbol to stop drawing off coffee prematurely.
The amount of coffee water you used last is saved by the
IMPRESSA until the next time you make coffee.
Press the Rotary Switch (1) briefly to check how much coffee
water you used last.
䡲 READY
䡲 Place a cup under the height-adjustable coffee spout (17).
䡲 Touch the (5).
䡲 COFFEE symbol
䡲 Select an aroma by touching one of the symbols
䡲 E.g. (STRONG aroma)
䡲 Touch the symbol (3).
䡲 HEATING UP
䡲 PRESS
MAINT.
䡲 Touch the symbol (7).
䡲 RINSING
䡲 READY
6.1 Rinsing the IMPRESSA without display request
䡲 Press the Rotary Switch (1) until
FILTER –/⻫ appears.
䡲 Turn the Rotary Switch (1) until
MAINTENANCE appears.
䡲 Press the Rotary Switch (1) to confirm.
䡲 RINSE
䡲 Press the Rotary Switch (1) again to confirm.
䡲 RINSING
䡲 READY
7. Adjusting the water quantity for coffee
The indicated value in ML is a reference value and may deviate
from the actual value
You can change/stop the water quantity during the draw-off
operation, too. Turn the Rotary Switch (1) until the required ML
value is displayed.
Page 13
13
E
䡲 STRONG
䡲 Touch the (8) symbol
䡲 160 ML (water quantity last adjusted).
䡲 The illuminated ring (2) is active.
䡲 Turn the Rotary Switch (1) until the required amount of coffee water
appears on the display (9).
䡲 e.g. 120 ML
䡲 COFFEE
䡲 Your coffee is being prepared.
䡲 READY
9. Making 2 cups of coffee
You cannot choose the strength of the coffee when making
2 cups. The machine automatically makes 2 mild cups of coffee.
You can set the amount of water you want with the Rotary
Switch (1) prior to drawing off coffee
Touch the (8) symbol to stop drawing off coffee prematurely.
The amount of coffee water you used last is saved by the
IMPRESSA until the next time you make coffee.
Press the Rotary Switch (1) briefly to check how much coffee
water you used last.
䡲 READY
䡲 Place two cups under the height-adjustable coffee spout (17).
䡲 Touch the coffee draw-off symbol of your choice twice
䡲 2 COFFEE
䡲 120 ML (water quantity last adjusted).
䡲 The illuminated ring (2) is active.
䡲 Turn the Rotary Switch (1) until the required amount of coffee water
appears on the display (9).
䡲 e.g. 210 ML
䡲 2 COFFEE
䡲 Your coffee is being prepared.
䡲 READY
10. Drawing off pre-ground coffee
Never use instant coffee or quick-coffee. We recommend that
you always use powder from fresh coffee beans or, pre-ground,
vacuum-packed coffee. Never fill in more than 2 portions of
powder. The pre-ground coffee tank is no storage tank. Make
sure that the pre-ground you use is not too fine. This may
cause blocking of the system. In this case the coffee only drips
out of the coffee spout.
If you have filled in too little powder, the message NOT
ENOUGH POWDER will be displayed. The IMPRESSA stops the
operation and returns to ‘ready for draw off’ mode.
You can stop the draw-off operation at any time by pressing
any coffee draw-off key.
䡲 READY
䡲 Put 1 or 2 cups under the adjustable coffee spout (17).
Page 14
14
䡲 Open the cover of the filler funnel for pre-ground coffee (11).
䡲 FILL
POWDER
䡲 Fill 1 or 2 level spoonfuls of pre-ground coffee in the filler funnel for
pre-ground coffee (11) (Fig. 15) and close the cover.
䡲 SELECT
KEY
䡲 Press the required draw-off key.
䡲 Touch the (8) symbol
䡲 120 ML (water quantity last adjusted)
䡲 The illuminated ring (2) is active.
䡲 Turn the Rotary Switch (1) again to select the water quantity indi-
vidually:
䡲 For Example: 210 ML
䡲 COFFEE
䡲 Your product is being prepared.
䡲 READY
11. Drawing off hot water
The amount of hot water you used last is saved by the
IMPRESSA until the next time you make coffee.
Install the hot water nozzle (see Fig. 5) to obtain perfect water
flow. Do not replace the replaceable hot water nozzle (16)
directly after drawing off water, because the nozzle is hot after
the draw-off operation.
At the start of the water draw-off operation there can be
splashing Avoid direct contact with the skin!
䡲 READY
䡲 Place a cup under the replaceable hot water nozzle (16).
䡲 Open the steam / hot water draw-off tap (14) (Fig. 12).
䡲 The illuminated ring (2) is active.
䡲 STEAM
䡲 Touch the (8) symbol
䡲 For example, 140 ML
䡲 WATER
䡲 Adjust the required water quantity by turning the Rotary Switch (1).
䡲 For example, 200 ML
䡲 WATER
䡲 If the required water quantity is reached, the following message is
displayed:
䡲 CLOSE TAP
䡲 Close the steam / hot water draw-off tap (14).
䡲 READY
Before CLOSE TAP water may still escape the system.
12. Dispensing steam
The steam function is used for the preparation of milk foam
and hot milk, as well as for the Professional Cappuccino Frother
(15) cleaning programme.
With the optionally available 2-stage frothing nozzle, liquids
can be heated and frothed using the steam function.
Page 15
15
E
Make sure that the nozzle is correctly fitted when drawing
steam. If the nozzle becomes blocked with particles of milk
residue or is incorrectly assembled, a danger can arise during
use whereby the nozzle may jump off.
Due to the system design, some water will escape at first when
steam is drawn. However, this will not affect the result in any
way.
When drawing steam, spluttering can occur at the start. The
nozzle becomes hot in use. Avoid any direct skin contact.
䡲 READY
䡲 To draw off steam, open the steam/hot water draw-off tap (14)
(Fig. 12).
䡲 The illuminated ring (2) is active.
䡲 STEAM
䡲 You can adjust the steam draw-off time individually by turning the
Rotary Switch (1) until the required SEC are displayed.
䡲 For example, 35 SEC
䡲 If you do not change the steam draw-off time settings using the
Rotary Switch (1), the machine will use the settings last adjusted.
䡲 During the steam draw-off operation, the message STEAM is dis-
played.
䡲 When the steam quantity is reached, the message CLOSE TAP is
displayed.
䡲 Close the steam / hot water draw-off tap (14).
䡲 READY
At any time, you can abort steam dispensing early, by closing
the tap for dispensing steam/hot water (14).
Before CLOSE TAP, steam may still escape the system.
13. Dispensing Cappuccino with the
Professional Cappuccino Frother
Cappuccino comprises one third each of Espresso, hot milk
and milk foam. You produce the milk portion with the Professional Cappuccino Frother (15).
When steam is drawn, a vacuum is produced which, with the
aid of the Professional Cappuccino Frother (15), draws in the
milk and produces milk foam.
To ensure perfect function, the Professional Cappuccino Frother
(15) must be cleaned regularly.
Make sure that the nozzle is correctly fitted. If the nozzle
becomes blocked with particles of milk residue or is incorrectly
assembled, a danger can arise during use whereby the nozzle
may jump off.
䡲 When using for the first time, remove the protective cover from the
Professional Cappuccino Frother (15) (Fig. 6). The protective cover is
used only during transport as protection to prevent the ingress of
contaminated materials.
䡲 Remove the milk pipe from the Welcome Pack and connect it to
the Professional Cappuccino Frother (15).
䡲 Insert the other end of the milk pipe into a Tetra Pak of milk or
connect it to a milk container (Fig. 7).
䡲 Place a cup under the Professional Cappuccino Frother (15) (Fig. 7).
Page 16
16
A useful addition is available for all lovers of milk specialities in
the form of high-quality vacuum milk containers. They keep
the milk cool the whole day long and are optimally suited to
the design of your IMPRESSA.
All original JURA accessories can be obtained from the specialist
shop.
䡲 Turn the selector switch of the Professional Cappuccino Frother (15)
to the milk foam position (Fig. 19).
䡲 READY
䡲 Open the steam / hot water draw-off tap (14) (Fig. 12). The milk
foam is prepared.
䡲 The illuminated ring (2) is active.
䡲 STEAM
䡲 You can adjust the steam draw-off time individually by turning the
Rotary Switch (1) until the required SEC are displayed.
䡲 For example, 35 SEC
䡲 If you do not change the steam draw-off time settings using the
Rotary Switch (1), the machine will use the settings last adjusted.
Adjust the steam dispensing time to suit the size of your cup.
䡲 During the steam draw-off operation, the message STEAM is dis-
played.
䡲 When the steam quantity is reached, the message CLOSE TAP is
displayed.
䡲 Close the steam / hot water draw-off tap (14).
䡲 READY
Due to the system design, steam can still escape and some
milk may continue to drip before the TAP is closed.
At any time, you can abort steam dispensing early, by closing
the tap for dispensing steam/hot water (14).
䡲 Now, move your cup with the milk foam and place it under the cof-
fee spout and dispense the required coffee product. (Fig. 8).
Your Cappuccino is ready.
13.1 Dispensing Hot Milk with the
Professional Cappuccino Frother
Turn the selector switch of the Professional Cappuccino Frother
(15) to the milk range (Fig. 21).
The procedure for dispensing hot milk is the same as the procedure for dispensing milk foam for Cappuccino (Chapter 13).
13.2 Cleaning of the
Professional Cappuccino Frother
To ensure that the Professional Cappuccino Frother functions
perfectly, you should rinse it with water each time after pre paring milk.
You will not be prompted by your IMPRESSA to rinse the Professional Cappuccino Frother.
13.3 Rinsing the Professional Cappuccino Frother
䡲 Carefully pull off the Professional Cappuccino Frother from your
IMPRESSA.
䡲 Dismantle the Professional Cappuccino Frother (15) into its indi -
vidual parts (Fig. 16).
Page 17
17
E
䡲 Thoroughly rinse all parts of the nozzle under running water.
䡲 Reassemble the Professional Cappuccino Frother (15) and refit it on
to your IMPRESSA.
13.4 Cleaning the Professional Cappuccino Frother
To ensure that the Professional Cappuccino Frother (15) functions perfectly, you should clean it daily if you have prepared
milk foam or hot milk.
You will not be prompted by your IMPRESSA to clean the Professional Cappuccino Frother (15).
You can obtain the JURA Auto-Cappuccino Cleaner from the
specialist shop.
䡲 Place a receptacle under the Professional Cappuccino Frother (15)
(Fig. 9).
䡲 Fill a second receptacle with 2.5 dl of fresh water and add one cap-
ful of the Auto-Cappuccino Cleaner.
䡲 Dip the milk pipe into the second receptacle with the Auto-
Cappuccino Cleaner (Fig. 9).
䡲 Turn the selector switch of the Professional Cappuccino Frother (15)
to the milk position (Fig. 21) or to the milk foam position (Fig. 19).
䡲 READY
䡲 Open the steam / hot water draw-off tap (14) (Fig. 12).
䡲 Draw steam until the receptacle with the Auto-Cappuccino Cleaner
is empty.
This procedure cleans the Professional Cappuccino Frother and the
milk pipe.
䡲 Close the steam / hot water draw-off tap (14).
䡲 READY
Before CLOSE TAP water may still escape the system.
䡲 Fill the receptacle with 2.5 dl of fresh water.
Dip the milk pipe into the receptacle with the fresh water.
䡲 Open the tap for dispensing steam/hot water (14) (Fig. 12) in order
to draw steam.
䡲 Draw steam until the receptacle with the fresh water is empty.
This procedure rinses the Professional Cappuccino Frother (15) and
the milk pipe with fresh water.
䡲 Cleaning of the Professional Cappuccino Frother (15) is now com-
plete, your IMPRESSA is ready for use.
14. Switching off the IMPRESSA
In order to ensure perfect operation, please don’t switch off
your IMPRESSA at the power switch (24) before all the symbols
on the display (9) have gone off except for (3).
䡲 READY
䡲 Switch off the IMPRESSA using the ON/OFF key (3).
䡲 RINSING
䡲 An automatic rinsing operation is started.
䡲
Your IMPRESSA is in standby mode.
Page 18
18
15. Programming
When your IMPRESSA leaves the factory it is adjusted such that
you can draw off coffee without having to change any settings.
However, you can programme various para meters individually.
You can programme the following stages:
쐌 Filter
쐌 Water hardness
쐌 Maintenance
쐌 Aroma
쐌 Temperature
쐌 Time
쐌 Automatic switch-on time
쐌 Automatic switch-off time
쐌 Draw-offs
쐌 Language
쐌 Display
쐌 Exit
To start programming, press the Rotary Switch (1) until
FILTER –/⻫ appears
Rotary switch
Turn the Rotary Switch to change the adjusted values or to
select the next programming step.
Press the Rotary Switch to check the values adjusted or to save
the values selected (Fig. 17).
15.1 Programming the filter
Refer to Chapter 5.1 ‘Inserting the filter’.
15.2 Programming the water hardness
Refer to Chapter 4 ‘Adjusting the water hardness’.
15.3 Maintenance menu
䡲 READY
䡲 Press the Rotary Switch (1) until
FILTER –/⻫ appears
䡲 The illuminated ring (2) is active.
䡲 Turn the Rotary Switch (1) until
MAINTENANCE appears
䡲 Press the Rotary Switch (1)
䡲 RINSE
䡲 Turn the Rotary Switch (1) until the required program item appears
on the display (9).
䡲 e.g. RINSE, CLEAN, FILTER, DE-SCALE or EXIT
䡲 e.g. CLEAN
䡲 Press the Rotary Switch (1)
䡲 The cleaning program starts.
䡲 EMPTY TRAY
䡲 Continue with Chapter 17 Cleaning, from point 3
EMPTY TRAY
15.4 Programming the aroma INTENSIVE
or STANDARD
When the machine leaves the factory, the aroma is set to
intensive. If requested it can also be set to Standard.
Page 19
19
E
䡲 READY
䡲 Press the Rotary Switch (1) until
FILTER –/⻫ appears
䡲 The illuminated ring (2) is active.
䡲 Turn the Rotary Switch (1) until Aroma is displayed.
䡲 AROMA
䡲 Press the Rotary Switch (1).
䡲 INTENSIVE
䡲 Turn the Rotary Switch (1) until the following message is displayed:
䡲 STANDARD
䡲 Press the Rotary Switch (1) to save the setting.
䡲 AROMA
䡲 Turn the Rotary Switch (1) until
EXIT appears
䡲 Press the Rotary Switch (1) to leave the programming mode.
䡲 READY
15.5 Programming the temperature
䡲 READY
䡲 Press the Rotary Switch (1) until
FILTER –/⻫ appears
䡲 The illuminated ring (2) is active.
䡲 Turn the Rotary Switch (1) until Temperature is displayed.
䡲 TEMPERATURE
䡲 Press the Rotary Switch (1).
䡲 HIGH
䡲 Turn the Rotary Switch (1) to change the temperature from HIGH to
NORMAL (or vice versa).
䡲 NORMAL
䡲 Press the Rotary Switch (1) to save the setting.
䡲 TEMPERATURE
䡲 Turn the Rotary Switch (1) until
EXIT appears
䡲 Press the Rotary Switch (1) to leave the programming mode.
䡲 READY
15.6 Programming the time
You must programme the time if you want to use the automatic switch-on function.
䡲 READY
䡲 Press the Rotary Switch (1) until
FILTER –/⻫ appears
䡲 The illuminated ring (2) is active.
䡲 Turn the Rotary Switch (1) until TIME is displayed.
䡲 TIME
䡲 Now press the Rotary Switch (1) to start programming the time.
䡲 --:--
䡲 Turn the rotary Switch (1) to adjust the hours..
䡲 12:--
䡲 Press the Rotary Switch (1) to confirm the hour settings and to
activate the minutes.
䡲 12:--
Page 20
20
䡲 Turn the Rotary Switch (1) to select the minutes.
䡲 2:05
䡲 Press the Rotary Switch (1) to save the setting.
䡲 TIME
䡲 Turn the Rotary Switch (1) until
EXIT appears
䡲 Press the Rotary Switch (1) to leave the programming mode.
䡲 READY
If the machine is disconnected from power supply, the time
must be programmed again.
15.7 Programming the automatic switch-on time
You must programme the time (Chapter 15.6) if you want to
use the automatic switch-on function (––:–– = inactive).
䡲 READY
䡲 Press the Rotary Switch (1) until
FILTER –/⻫ appears
䡲 The illuminated ring (2) is active.
䡲 Turn the Rotary Switch (1) until MACHINE ON is displayed.
䡲 MACHINE ON
䡲 Now press the Rotary Switch (1) to start programming the switch-
on time.
䡲 --:--
䡲 Turn the Rotary Switch (1) to adjust the hours.
䡲 12:--
䡲 Press the Rotary Switch (1) to confirm the hour settings and to acti-
vate the minutes.
䡲 12:--
䡲 Turn theRotary Switch (1) to select the minutes.
䡲 12:05
䡲 Press the Rotary Switch (1) to save the setting.
䡲 MACHINE ON
䡲 Turn the Rotary Switch (1) until
EXIT appears
䡲 Press the Rotary Switch (1) to leave the programming mode.
䡲 READY
15.8 Programming the automatic switch-off time
You can programme your coffee machine such that it will
switch off automatically after a certain time. You can programme the switch-off time in a range between 0.5 and
9 hours, or select ––:–– (i.e. inactive).
䡲 READY
䡲 Press the Rotary Switch (1) until
FILTER –/⻫ appears
䡲 The illuminated ring (2) is active.
䡲 Turn the Rotary Switch (1) until OFF AFT. HR is displayed.
䡲 OFF AFT. HR
䡲 Now press the Rotary Switch (1) to start programming the switch-
off time. Switch-off time OFF AFT. HR
䡲 5.0 HR
Page 21
21
E
䡲 Turn the Rotary Switch (1) to adjust the hours.
䡲 1.0 HR
䡲 Press the Rotary Switch (1) to save the setting.
䡲 OFF AFT. HR
䡲 Turn the Rotary Switch (1) until
EXIT appears
䡲 Press the Rotary Switch (1) to leave the programming mode.
䡲 READY
15.9 Cup counter
This function is available with the following types of coffee:
a) 1 LARGE CUP
b) 1 COFFEE
c) 1 ESPRESSO
d) 1 powder coffee
e) 2 COFFEE
䡲 READY
䡲 Press the Rotary Switch (1) until
FILTER –/⻫ appears
䡲 The illuminated ring (2) is active.
䡲 Turn the Rotary Switch (1) until
CUPS MADE appears
䡲 Press the Rotary Switch (1)
䡲 100
䡲 Press one of the draw-off keys / / to check the number of
individual cups made.
䡲 E.g press draw-off key 1 cup of coffee (5).
䡲 20
You can check the number of pre-ground cups of coffee by
opening the filler funnel for pre-ground coffee (11).
䡲 Touch one of the symbols / / to check how often you
made 2 cups of coffee.
䡲 To quit press the Rotary Switch (1).
䡲 CUPS MADE
䡲 Turn the Rotary Switch (1) until
EXIT appears
䡲 Press the Rotary Switch (1) to leave the programming mode.
䡲 READY
15.10 Programming the language
䡲 READY
䡲 Press the Rotary Switch (1) until
FILTER –/⻫ appears
䡲 The illuminated ring (2) is active.
䡲 Turn the Rotary Switch (1) until LANGUAGE is displayed.
䡲 LANGUAGE
䡲 Now press the Rotary Switch (1) to start programming the item
LANGUAGE.
䡲 Turn the Rotary Switch (1) until the required language is dis played.
䡲 For example ENGLISH
䡲 Press the Rotary Switch (1) to save the setting.
Page 22
22
䡲 LANGUAGE
䡲 Turn the Rotary Switch (1) until
EXIT appears
䡲 Press the Rotary Switch (1) to leave the programming mode.
䡲 READY
15.11 Programming Display 24H/AM/PM
䡲 READY
䡲 Press the Rotary Switch (1) until
FILTER –/⻫ appears
䡲 The illuminated ring (2) is active.
䡲 Turn the Rotary Switch (1) until
DISPLAY appears
䡲 Press the Rotary Switch (1)
䡲 ML/OZ appears
䡲 Turn the Rotary Switch (1) until
24H/AM PM appears
䡲 Press the Rotary Switch (1)
䡲 e.g. 24H
䡲 Select a setting of your choice.
䡲 Press the Rotary Switch (1) to save the setting.
䡲 DISPLAY
䡲 Turn the Rotary Switch (1) until
EXIT appears
䡲 Press the Rotary Switch (1) to leave the programming mode.
䡲 READY
15.12 Programming the display for ML/OZ
䡲 READY
䡲 Press the Rotary Switch (1) until
FILTER –/⻫ appears
䡲 The illuminated ring (2) is active.
䡲 Turn the Rotary Switch (1) until
DISPLAY appears
䡲 Press the Rotary Switch (1)
䡲 ML/OZ appears
䡲 Press the Rotary Switch (1)
䡲 e.g. ML
䡲 Select a setting of your choice.
䡲 Press the Rotary Switch (1) to save the setting.
䡲 DISPLAY
䡲 Turn the Rotary Switch (1) until
EXIT appears
䡲 Press the Rotary Switch (1) to leave the programming mode.
䡲 READY
15.13 Exit programming mode
䡲 READY
䡲 Press the Rotary Switch (1) until
FILTER –/⻫ appears
䡲 The illuminated ring (2) is active.
䡲 Turn the Rotary Switch (1) until
EXIT appears
Page 23
23
E
䡲 Press the Rotary Switch (1) to leave the programming mode.
䡲 READYM
16. Maintenance
16.1 Filling in water
䡲 FILL
WATER
If this information is displayed, drawing off products is no
longer possible. Refill water as described in Chapter 2.3.
䡲 READY
The water tank should be rinsed daily and refilled with fresh
water. Only fill in fresh, cold water. Never fill in milk, mineral
water or other liquids.
16.2 Emptying the coffee grounds container
䡲 EMPTY
GROUNDS
If this message appears on the display, you can no longer draw
off coffee. You must empty the coffee grounds con tainer (18)
first (Fig. 13).
䡲 Carefully take out the drip tray (20), it is filled with water.
䡲 NO
TRAY
䡲 Insert the empty and clean trip tray (20) again.
䡲 READY
The red water level indicator appears when the drip tray (20) is
full.
16.3 Drip tray missing
䡲 NO
TRAY
䡲 If this information is displayed, the drip tray (20) is not installed
properly or was not installed at all.
䡲 Insert the drip tray (20).
䡲 READY
16.4 Fill coffee beans
䡲 FILL
BEANS
䡲 Refill beans as described in Chapter 2.4.
The message REFILL BEANS will disappear after you draw off
your next cup of coffee.
We recommend that you clean the bean tank regularly before
refilling beans, using a dry cloth. Before cleaning the tank,
switch off the IMPRESSA.
16.5 Replacing the filter
After drawing off 50 litres, the filter cartridge will be used up. A
message requesting you to replace the filter will appear on the
display.
Refer to Chapter 5.2 ‘Replacing the filter’.
Page 24
24
16.6 Cleaning the IMPRESSA
After 200 draw-off operations or after 80 rinsing operations, the IMPRESSA must be cleaned. A message appears on the display, telling
you to start the cleaning programme. You can still draw off coffee or
hot water/steam. However, we recommend that you should clean the
machine (Chapter 17) within the next few days.
䡲 CLEAN MACHINE / MACHINE READY
16.7 IMPRESSA calcified
During operation, the machine will calcify. The degree of scaling depends on the hardness of the water in your region. The machine will
inform you when descaling is required. You can still draw off coffee or
hot water/steam. However, we recommend that you should de-scale
the machine (Chapter 18) within the next few days.
䡲 MACHINE CALCIFIED / MACHINE READY
16.8 General cleaning instructions
䡲 Never use scratching objects, pan cleaners, cleaning sponges or
caustic chemicals to clean the machine.
䡲 Wipe off the case on the inside and outside using a soft, moist
cloth.
䡲 Clean the replaceable hot water nozzle after each use.
䡲 To ensure that the Professional Cappuccino Frother functions per-
fectly, you should rinse it with water each time after pre paring milk.
䡲 To ensure that the Professional Cappuccino Frother functions per-
fectly, you should clean it daily if you have prepared milk.
䡲 The water tank should be rinsed daily and refilled with fresh water.
If the water tank shows signs of scaling, remove the scaling
using a commercial descaling agent. Take out the water tank
(Fig. 4).
Remove the CLARIS plus filter cartridge, if installed, before
descaling the water tank.
16.9 Emptying the system
Precondition: IMPRESSA switched off
This operation is required to protect the IMPRESSA against
frost damage during transports.
䡲 Place a receptacle under the Professional Cappuccino Frother (15)
(Fig. 10).
䡲 Turn the selector switch of the Professional Cappuccino Frother (15)
to the steam position (Fig. 20).
䡲 OPEN TAP
䡲 Press the Rotary Switch (1)
䡲 EMPTYING
䡲 CLOSE TAP
䡲 The IMPRESSA is switched off.
Page 25
25
E
17. Cleaning
Your IMPRESSA features an integrated cleaning program. The cleaning operation will take some 15 min.
Original JURA cleaning tablets which are specially designed for
the cleaning program of your IMPRESSA are available at your
authorized dealer. Please note that machine defects or residues
in the water cannot be excluded if you use inappropriate cleaning agents.
Once started, the descaling operation must not be inter rupted!
After each cleaning operation the filler funnel for pre-ground
coffee should be cleaned (11).
䡲 READY
CLEAN
䡲 Touch the symbol (7).
䡲 EMPTY
TRAY
䡲 Empty the tray (20).
䡲 NO
TRAY
䡲 Insert the tray (20) again.
䡲 Remove the drip grate (19).
䡲 Put a container (1 l, Fig. 11) under the adjustable coffee spout (17).
䡲 PRESS
MAINT.
䡲 Touch the symbol (7).
䡲 CLEANING
䡲 FILL
TABLET
䡲 Fill in the tablet (see Fig. 14)
䡲 PRESS
MAINT.
䡲 Touch the symbol (7).
䡲 CLEANING
䡲 EMPTY
TRAY
䡲 NO
TRAY
䡲 READY
䡲 Wipe coffee powder tank with a dry cloth after the cleaning pro-
gram has finished.
䡲 The cleaning operation was completed successfully.
17.1 Cleaning without display request
䡲 Press the Rotary Switch (1) until
FILTER –/⻫ appears.
䡲 Turn the Rotary Switch (1) until
MAINTENANCE appears.
䡲 Press the Rotary Switch (1) to confirm.
䡲 RINSE
䡲 Turn the Rotary Switch (1) until
CLEAN appears.
Page 26
26
䡲 Press the Rotary Switch (1) again to confirm.
䡲 EMPTY TRAY
䡲 The program ‘Clean’ is now active. Now proceed as described in
Chapter 17 from EMPTY TRAY onwards.
18. Descaling
Your IMPRESSA features an integrated descaling program. The cleaning operation will take some 40 min.
Original JURA descaling tablets which are specially designed for
the descaling program of your IMPRESSA are available at your
authorized dealer. Please note that machine defects or residues
in the water cannot be excluded if you use inappropriate
descaling agents.
If the IMPRESSA needs descaling, the corresponding message is
displayed.
You can still draw off coffee or hot water/steam and start the
descaling program later.
Before starting the descaling program, the machine must be
switched off. Once started, the descaling operation must not be
interrupted.
When using the descaling agent, immediately remove any
splashes or drips from sensitive surfaces, i.e. natural stone and
wooden surfaces, or take appropriate precautions.
In any case wait until the descaling agent is used up and the
tank is empty. Never refill descaling agent.
䡲 MACHINE CALCIFIED / MACHINE READY
䡲 Remove the Professional Cappuccino Frother (15).
䡲 Touch the symbol (7).
䡲 EMPTY
TRAY
䡲 Empty the tray (20).
䡲 NO
TRAY
䡲 Insert the tray (20) again.
䡲 AGENT
IN TANK
Completely dissolve the content of one blister (3 tablets) in a jug
containing 0.5 litres of water, and fill the mixture in the water tank.
Reinstall the water tank.
䡲 OPEN TAP
AGENT
IN TANK
䡲 Place a receptacle under the hot water spout (Fig. 18).
䡲 Open the steam / hot water draw-off valve (14) (Fig. 12).
䡲 DE-SCALING
䡲 CLOSE TAP
䡲 Close the steam / hot water draw-off tap (14).
䡲 DE-SCALING
䡲 EMPTY
TRAY
䡲 Empty the tray (20).
䡲 NO
TRAY
Page 27
27
E
䡲 Insert the tray (20) again.
䡲 FILL
WATER
Rinse the water tank thoroughly and fill it with cold, fresh tap
water. Install it again.
䡲 OPEN
TAP
䡲 Open the steam / hot water draw-off tap (14) (Fig. 12).
䡲 DE-SCALING
䡲 CLOSE TAP
䡲 After you have closed the steam / hot water draw off tap (14), the
following message is displayed
䡲 DE-SCALING
䡲 EMPTY
TRAY
䡲 Empty the tray (20).
䡲 NO
TRAY
䡲 Insert the tray (20) again.
䡲 PRESS
MAINT.
䡲 Touch the symbol (7).
䡲 RINSING
䡲 READY
䡲 The descaling operation was completed successfully.
18.1 Decalcifying without display request
Decalcifying without display request is only possible if the
CLARIS plus filter is NOT programmed.
䡲 Press the Rotary Switch (1) until
FILTER – appears.
䡲 Turn the Rotary Switch (1) until
MAINTENANCE appears.
䡲 Press the Rotary Switch (1) to confirm.
䡲 RINSE
䡲 Turn the Rotary Switch (1) until
DECALC. ON appears.
䡲 Press the Rotary Switch (1) again to confirm.
䡲 EMPTY TRAY
䡲 The program ‘De-scale’ is now active. Now proceed as described in
Chapter 18 from EMPTY TRAY onwards.
19. Disposal
Please dispose of old machines in an environmentally
neutral way.
Old machines contain valuable materials capable of being
recycled which should be salvaged for recycling. Please
therefore dispose of old machines via suitable collection
systems.
Page 28
28
20. Tips for perfect coffee
Height-adjustable coffee spout (17)
You can adjust the height of the coffee spout to the size of your cups
(Fig. 3)
Grinding degree
Refer to Chapter 2.5 ‘Adjusting the grinding gear’.
Preheating cups
You can preheat the cups using hot water or steam. The smaller the
coffee you want to draw off, the more important preheating is.
Sugar and cream
Stirring coffee/tea will result in heat being released. Adding
refrigerated cream or milk will reduce the temperature of the coffee
significantly.
Page 29
29
E
21. Messages
Cause Remedy
FILL WATER Water tank is empty. Refill water
Float defective Rinse or de-scale water tank
FILL BEANS Bean tank is empty. Refill beans
Although you have refilled beans, the Draw off a cup of coffee. The message will
message still appears. disappear only after you have drawn off a cup
of coffee
EMPTY GROUNDS Coffee grounds container full Empty coffee grounds container
Tray reinstalled too early after emptying Wait 10 sec. before reinstalling the tray
NO TRAY Drip tray not installed properly or missing Install tray properly
CLEAN MACHINE / Cleaning required Start cleaning programme (Chapter 17)
MACHINE READY
MACHINE CALCIFIED / Descaling required Start descaling programme (Chapter 18)
MACHINE READY
CHANGE FILTER / Filter used up Replace filter (Chapter 5.2)
MACHINE READY
ERROR General fault – switch off
– disconnect from mains supply
– Connect IMPRESSA to power supply
– Switch on IMPRESSA
– Have IMPRESSA checked by JURA
– Service
Page 30
30
22. Problems
Problem Cause Remedy
Very loud noise coming from the Foreign body in grinding gear Drawing off pre-ground coffee still possible
grinding gear
Have IMPRESSA checked by JURA Service
Too little foam when Professional Cappuccino Frother has Clean the Professional Cappuccino Frother
frothing the milk become dirty (Chapter 13)
Individual parts of the Professional Check correct assembly of the
Cappuccino Frother are incorrectly Professional Cappuccino Frother
assembled
Coffee only drips Grinding degree too fine Coarser grinding gear adjustment
from the coffee spout
Pre-ground coffee too fine Use a coarser pre-ground coffee
High-frequency, electromagnetic interference may influence the display. Drawing off coffee is possible at any time.
If the messages or problems still persist, please contact your local authorized dealer or JURA Elektroapparate AG.
Page 31
31
E
23. Legal information
These operating instructions contain all the information required for
using, operating and maintaining the machine properly.
Knowledge of and compliance with the specifications contained in
these operating instructions is required for using the machine safely
as well as for operational safety and safety during maintenance.
These operating instructions cannot cover any conceivable appli cation. The machine was designed for private household use.
Additionally we point out that the content of these operating
instructions does not form part of any previous or existing agreement, consent or al legal relationship nor does it constitute a change
of such an agreement, consent or legal relationship. Any obligations
to be fulfilled by JURA Elektroapparate AG are stipu lated in the corresponding purchase contract, which also contains the full and solely
applicable warranty stipulations. These con tractual warranty stipulations are neither extended nor limited by the specifications contained
in these operating instructions.
The operating instructions contain information, protected by Copyright. Photocopying or translations into other languages shall not be
permissible without JURA Elektroapparate AG’s written approval.
24. Technical data
Voltage: 230V AC
Power: 1450 W
Intensity of current: 10 A
Safety check:
Energy consumption Standby: approx. 3.5 Wh
Energy consumption
‘Ready for draw-off’ mode: approx. 11.5 Wh
Pump pressure: static, max. 15 bar
Water tank: 1.9 litres
Bean tank capacity: 200gr
Coffee grounds container capacity : max. 16 portions
Length of cable: approx. 1.1 m
Weight: 9.1 kg
Size (WxHxD): 28 x 34.5 x 44.5 cm
The machine complies with the following EU directives:
73/23/EWG dated 19/02/1973 ‘Low Voltage Directive’ including Modification Directive 93/336/EWG
89/336/EWG dated 03/05/1989 ‘EMC Directive’ including
Modification Directive 92/31/EWG
Page 32
Art. 66380 – 5/07
JURA-Elektroapparate AG – Kaffeeweltstrasse 10 – CH-4626 Niederbuchsiten
www.jura.com
Loading...