JUNO Atrius Installation Instructions Manual

INSTALLATION INSTRUCTIONS

Atrius™-Ready Bluetooth® Low Energy (BLE)
Indoor Postioning Module for Juno® Trac-Master™
Instructions (TIPM)

Read all of these installation instructions before installing the TIPM.
Save these instructions and refer to them when uninstalling/reinstalling
TIPM. Use only with Juno T, TU, R or V series Trac.

POLARITY

TIPM is visually polarized to enable proper connections.

NOTE:

1. Trac face has a polarity line indicating “p” positive side.

2. Make sure power is OFF before wiring.

Rotation direction
after insertion

TIPM view
from above

One Circuit Trac

Polarity Line

TIPM is marked with a Polarity Line. This should line up to the
polarity line on the track for initial insertion.
TIPM should then be rotated clockwise until parallel with the track,
when installing from beneath track, as indicated by arrow on TIPM.

Two Circuit Trac

Polarity Line

Warning: Changes or modifications to this device not expressly approved by Acuity Brands Lighting, Inc. could void the user’s authority to operate

the equipment.
“This equipment complies with FCC radiation expccure limits set forth for an uncontrolled environment. This equipment should be installed and

operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.”

Under industry Canada regulations, this radio transmitter may only operate using an antenna of a type and’ maximum (or lesser) gain approved
for tile transmitter by industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen
that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

Conformément à la réglementation d’lndustrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain
maximal (ou intérieur) approuvé pour l’émetteur par lndustrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention
des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse
pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.

This radio transmitter (identify the device by certification number, or model number if Catagory II) has been approved by Industry Canada to
operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this
device.

Le présent émetteur radio (identifier le dispositif par son numéro de certification ou son numéro de modèle s’il fait partie du matériel de catégorie
I) a été approuvé par Industrie Canada pour fonctionner avec les types d’antennes énumérés ci-dessous et ayante un gain admissible maximal et
l’impédance requise pour chaque type d’antenne. Les types d’antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal
indiqué, sont strictement interdits pour l’exploitation de l’émetteur.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’éxploitation est autorisée aux
deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

Polarity Line

1300 S. Wolf Road • Des Plaines, IL 60018 • Phone [phone] • Visit us at www.acuitybrands.com/juno-trac
©2017 Acuity Brands Lighting, Inc. Rev. 04/18 P4467

1 of 2

INSTALLATION INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

Save these instructions for future reference

BEFORE INSTALLATION, READ AND FOLLOW ALL SAFETY INSTRUCTIONS!

IMPORTANT SAFETY INSTRUCTIONS

Save these instructions for future reference

IMPORTANT SAFETY INSTRUCTIONS

Save these instructions for future reference

To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards
please read all warnings and instructions included with and on the fixture box and all fixture labels.
Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
Commercial installations: service and maintenance of luminaires should be performed by a qualified licensed electrician.
Residential installation: If you are unsure about the installation or maintenance of the luminaires, consult a qualified licensed electrician
and check your local electrical code. This fixture is intended to be connected to a properly installed and grounded UL listed junction box.
DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly packed so that no parts should have been damaged during
transit. Inspect to confirm. Any damaged or broken parts should be replaced. For availability of replacement parts contact Technical
support.
If the lamp is marked (Hg) it contains Mercury. Follow all disposal laws. See www.lamprecycle.org.
Fixture can NOT be used with dimmer switch, motion or occupancy sensors and other electronic switching devices unless otherwise
designated.
These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in
connection with installation, operation, or maintenance. Should further information be desired or should particular problems arise which
are not covered sufficiently for the purchaser’s or owner’s purposes, this matter should be referred to Acuity Brands Lighting, Inc.

BEFORE INSTALLATION, READ AND FOLLOW ALL SAFETY INSTRUCTIONS!

approved recognized wire connectors.

WARNING

RISK OF ELECTRIC SHOCK

WARNING

RISK OF BURN

as these may be hazardous to children.

CAUTION

RISK OF INJURY

CAUTION

To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards
please read all warnings and instructions included with and on the fixture box and all fixture labels.
Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
Commercial installations: service and maintenance of luminaires should be performed by a qualified licensed electrician.
Residential installation: If you are unsure about the installation or maintenance of the luminaires, consult a qualified licensed electrician
and check your local electrical code. This fixture is intended to be connected to a properly installed and grounded UL listed junction box.
DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly packed so that no parts should have been damaged during
transit. Inspect to confirm. Any damaged or broken parts should be replaced. For availability of replacement parts contact Technical
support.
If the lamp is marked (Hg) it contains Mercury. Follow all disposal laws. See www.lamprecycle.org.
Fixture can NOT be used with dimmer switch, motion or occupancy sensors and other electronic switching devices unless otherwise
designated.
These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in
connection with installation, operation, or maintenance. Should further information be desired or should particular problems arise which
are not covered sufficiently for the purchaser’s or owner’s purposes, this matter should be referred to Acuity Brands Lighting, Inc.

 Turn off electrical power at fuse or circuit breaker box

before wiring fixture to the power supply.

 Turn off the power when you change lamps or perform

other maintenance.

 Verify that supply voltage is correct by comparing it

with the luminaire label information.

 Make all electrical and grounded connections in

accordance with the National Electrical Code and any
applicable local code requirements.

 All wiring connections should be capped with UL

 Allow lamp/fixture to cool before handling. Do not

touch hot lens, lamp, guard, or enclosure.

 Do not exceed maximum wattage marked on luminaire

label.

 Follow all lamp manufacturer’s warnings,

recommendations and restrictions on lamp operation
including but not limited to: ballast type, burning
position, replacement, and recycling.

 Use only lamps that comply with ANSI standards.

 Wear gloves and safety glasses at all times when

removing luminaire from carton, installing, servicing or
performing maintenance.

 Avoid direct eye exposure to the light source while it is

on.

 Account for small parts and destroy packing material,

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Acuity
Brands Lighting is under license.

Technical Services Phone [phone]

1300 S. Wolf Road • Des Plaines, IL 60018 • Phone [phone] • Visit us at www.acuitybrands.com/juno-trac
©2017 Acuity Brands Lighting, Inc. Rev. 04/18 P4467

 Keep combustible and other materials that can burn

away from luminaire and lamp/lens.

 Maximum 90 degree C supply conductor
 This fixture should NOT be used in areas with limited

or restricted ventilation or high ambient temperatures.

2 of 2