Receiver System RP-3000
(Instruction Manual)
A/B /C
BT
USB
AUX
(BT/DVD/CD/MP3/SD/USB/AM/FM/CLOCK)
BEFORE USING PLEASE READ THIS MANUAL CAREFULLY
COMPATIBLE DISCS
4.72"
4.72"
4.72"
ACCESSORIES
1 X Instruction manual
1 X Remote control
1 X FM-Antenna (Pig Tail)
One composite audio/video cable
6 X Mounting Screws
Wire Harness for DC power and speakers
DC Power extension (Red and Black wire) wires
Optional AC/DC Adapter
2 X Batteries
4.72"
1
Location of Controls
17
16
1
2
3
4
A/B /C
5
6
7
USB
8
9
1 Tune-/Previous button
4 Reset button
(NOTE)
7 Disc loader
10 AUX
13 Eject button
16 LED display
2 Function button
5 Audio channel switch
8 SD card slot
11 Tune+ / Next button
14 Stop button
17 Remote sensor
AUX
3 Standby button
6 Volume - button
9 USB port
12 Play/ Pause button
15 Volume+ button
15
14
13
12
11
10
NOTE 4:This reset button is under screw cover.when unit is frozen for some reason,remove the left side
screw cover,use a paper clip and reset.
2
DVD/USB/SD/RADIO/TV/AUX ICONS DISPLAY
MOUNTING AND CUT OUT INSTRUCTIONS
The 6X mounting screws are in the owner’s manual bag.
Note:
·Remove screw caps and carefully take mounting covers off.
·Connect and test hareness and wiring before wiring.
·Screw the unit in place, replace screw caps.
3
REFERENCE DRAWING FOR REAR CABINET
1
2
3 4
AUX TV
5
(
O
U
TP
U
T)
1 Automotive antenna socket (AM/FM/)
2 Wire harness for 12V DC power and 6 speakers
3 CVBS(2 Video output) 4 Aux (L/R) TV audio input
5 HDMI OUTPUT
4
Wire harness for 12V DC power & 6 speakers guide diagram
Carefully read wiring diagram: the wrong connections reversing polarity
(positive and negative power wiring) can cause distortation and / or damage the power amplifiers.
Basic Operations
TIME SETUP
1.Press to enter standby mode, press and hold CADJ/MEMO button on the remote control to enter time setup interface.
The LED
2. Press UP and down to select 12 or 24 hours mode, then press CADJ/MEMO to confirm, after confirming, the hour digit
will be flashing, press UP or DOWN button to adjust hour, press CADJ/MEMO again to confirm hour.
3. Once completed, the minute digit will be flashing, then press the UP or DOWN button to adjust minute. when finished,
Press CADJ/MEMO to confirm, time setting is over.
display will show the default time with the hour digit flashing.
MODE SHIFT
1. When in standby mode, press the power button on the unit or remote to turn on the unit.
2. Press FUNC button on the remote control or FUNC button on the unit to shift modes between
bt /DVD/USB/SD/FM/AM/ TV/AUX.
Note
-Once the disc is loaded, the unit will automatically shift to DVD mode.
BLUETOOTH
1. Press FUNC button on the remote control until " bt " appears on the screen.
2. Activate the Bluetooth connection on the external device.
3. The unit will search and reconnect to previous bluetooth device that was connected if available. If it is your first
time connecting,
4. Press PREV and NEXT buttons to skip to the previous and next track..
5. Press button to select play or pause mode.
find "RP3000BT" in your device pairing list and select it to pair and connect your device to the unit.
Note
-Skip and play/pause functions may not be compatible with all connected bluetooth devices.
5
DISC PLAYBACK
1.One disc is inserted, unit will automactically shift to DVD mode and begin playback.
2.Press button to eject the disc.
3.Press buttons to go through the menu and press ENTER button to confirm the selections.
4.Press PREV and NEXT button to skip to the previous or next chapter / track..
5.Press REV and FWD buttons to search through the chapter/track backward and forward at different speed.
6. Press ANGLE button to select different camera angles that available in the disc.
7. Press SUBTITLE button to select a different subtitle language if available on the disc.
8. Press TITLE button to enter title menu.
9. Press MENU button to enter disc root menu.
10. Press OSD button to display the disc inforamtion.
Note
-Function mentioned above may not be available on all the discs.
USB/SD CARD PLAYBACK
1. Insert USB drive or USB card into appropriate slot.
2. Press FUNC button until indicator light shows USB or SD.
3. Press buttons to go through the menu and press ENTER button to confirm the selection.
Note
-The USB player supports MP3/ AVI /WMA/JPEG formats.
TV/AUX PLAYBACK
1. Connect your external audio device (MP3 player/cell phones, etc.) to the AUX IN 2 jack in the front
of the unit with an 3.5mm audio cable (not supplied). Or connect DVD player, VCR, DVR, etc to the
AUX 1 jack in the rear of the unit with the RCA audio cable.
2. Press FUNC button on the remote control until desired indicator light, either TV or AUX is highlighted.
3. Activate your external device.
Note
-The TV can also connected to the VIDEO OUT in the rear of the unit with an AV cable to watch video files.
PLAY RADIO
1. Use function button to cycle to either FM or AM which will be shown with indicator light on LED diaplay.
2. Press and hold ( or ) button to seach stations automatically. To store a searched station,
press MEMO button, the screen will diaplay the order, eg: P01, then press MEMO again to confirm.
Press CH- and CH+ button to play the stored station.
3. when a station searched, press MEMO to display the storage, press CH+ or CH- to select a order,
eg:select P20 as the storage position, press MEMO to confirm the position. next time, press CH+
or CH- to find P20 to play the station stored.
4.. Press MEMO button on the remote control to display on the LED the preset for selected station.
5. Press CH + and CH- buttons on the remote control to select and play the stored stations..
Note
-A total of 30 AM stations and 30 FM stations can be stored into the unit's memory.
- Fully extend and relocate the antenna to improve the reception.
6
REFERENCE DIAGRAM AND KEY FOR REMOTE CONTROL
10
11
12
1
2
3
4
5
6
SEA RCH +
7
SEA RCH -
8
13
14
15
16
17
18
19
20
21
22
9
23
24
25
26
CAD J/ M E O
M
27
28
29
1 POWER
4
PREV
7 CH-
10 NUMBER KEYPAD
13
16
19
22
EJECT
FWD
SEARCH+
VOL-
DISC
25 MUTE
28
ANGLE
2 TITLE
5
NEXT
8 SETUP
11
CADJ/MEMO
14 FUNC
17
20
23
REV
CH+
PAIR
/
26 REPEAT
29
OSD
7
3 MENU
6 STOP
9 SEARCH12
15
18
A/B/C
SUBTITLE
VOL+
21 ENTER
24
AUDIO
27 TONE
1 POWER
Press this button to shut off power and enter standby mode, press it again to activate.
2 TITLE
Press this button to access the DVD menu.
3 MENU
Press this button to switch the menu mode. For a DVD, press MENU to open the menu during playback.
4 PREV
Press this button to skip back to the previous selection.
5 NEXT
Press this button to skip to the next chapter/track.
6 STOP
Press this button to stop play for the current DVD or CD. Press the /ENTER button to resume playback.
7 CH –
Press this button to select last station.
8 SETUP
Press this button and the setup screen will appear if available for the current mode .
9 SEARCH-
Press this button to search previous radio channal.
10. NUMBER KEYPAD
Press these button to select channel
11. CADJ/MEMO
Set the clock time.
12. A/B/C
Press this button to select desired speaker channel.
13.
Press this button to eject CD or DVD. Don't press to load as discs load automactically.
14. FUNC
Press this button to store a desired station to memory.
Press this button to choose between AM and FM radio modes and select the desired DVD, AUX, TV
or BLUETOOTH mode.
8
15. SUBTITLE
Press this button to select different subtitle languages if applicable.
16. FWD
Press this button to play fast forward, each time it is press,
Continue pressing it to return back to normal playback speed.
the speed with which it fast forward.
17. REV
Press this button to rewind. Each time it is pressed, the speed with which it rewinds accelerates. Conitune pressing it
to return back to normal playback speed.
18. VOL+
Press t
his button to turn the volum
e up.
19. SEARCH +
his button to search next radio channel.
Press t
CH +
20.
his button to select the next station.
Press t
21.
ENTER
Press this button to confirm the desired/hightlighted selection.
22.VOL
–
Press t
his button to turn the volume down.
23. /PAIR
his button to pairing blue tooth, pause the playing track or vedio, press again to replay.
Press t
24. AUDIO
Press this button to enter audio mode.
25. MUTE
Press this button to turn off sound, press again to resume.
26. REPEA
T
For DVD or CD, press this button to repeat current chapter or track. Press it again to repeat the entire DVD or CD.
27. TONE
Press t
his button to
.
ANGLE
28
Press this button to select
change audio settings, such as speakers base and treble level.
different viewing angles if available.
29. OSD
Press to show status information on the screen.
9
For
your convenience, we have enlisted some points to solve problems, you may encounter while using the
TM
CONNEX RP3000BT.
TM
X
No Sound
*M
ake sure th
e connections are secure between player and speakers.
*Make sure the correct input is selected on the monitor.
No Pictur
*Make sure the connecti
*M
e
on are secure between RP3000BT and the monitor.
ake sure the RP3000BT is in the correct mode (e.g., DVD mode)
Disc does not play
*Make sure the disc is loaded correctly (label side is facing up on the disc tray
ake sure the disc is clean and not dama
*M
Remote contr
oller does not work
ged.
*Move any obstacles between RP3000BT and remote control.
*Poi
nt the remote controller at the remote control sensor
.
*Check the battery.
TECHNICAL
SPECIFICATIONS
).
Laser
Wave length 650um
Video AUTO/NTSC
Frequency response 20 Hz-20KHz
Signal/noise ratio >60dB
Dynamic rang >60dB(1KHz)
Video out output level:1vp-p/ Load impedance :75 imbalance/
negative polarity
Power supply DC 12-14.4V
Power consumption
<55W
Dimensions (WxHxD) 218(L)x185(H)x169(D)mm
AM Frequency range AM 520 ~ 1710KHz
FM Frequency range FM87.5 ~ 108MHz
Output power 30W(RMS)
10
FCC Warning:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
Loading...