Junlan Electronic CHT914C User Manual

Download

CONVERTIBLE

SPEAKER SYSTEM

Owner's Manual

PLEASE READ BEFORE OPERATING THIS EQUIPMENT.

Model: CHT914c

Size: 148.5(W) x 210(H)mm (A5)

IMPORTANT SAFETY INSTRUCTIONS

This unit has a long AC cord and other long cord that can easily be tripped on or pulled on, causing injury. Please make sure

it is

arranged so it will not drape over a laptop, etc. Where it can be pulled on by children or tripped over accidentally.

INSTALLATION

This unit can be assembled as the following methods: This unit can be assembled as the following methods:

Method 1: Assemble the main unit and L Speaker together :

Main Unit

Left Speaker

Supplied Wooden Stand

Supplied Metallic Screws and Washers

Left Speaker

Lock the Hook on the rear of left speaker to the Main unit as Fig.

Note: We supplied total two Wooden Stands and 4 sets Metallic Screws/Washers.Keep the

excess accessories in this assembly method for future use.

Method 2: Assemble Main Unit and L Speaker individually :

Main unit

Left Speaker

Supplied

Wooden Stand

Supplied Metallic

Screws and Washers

Decorative Inserts

The speaker net can be take out and reassembly as the Figure below:

After above installation, connect the connection wires (Red and Black) from L Speaker to

the Speaker Connectors on the rear of Main Unit as the figure below:

Black wire

Main Unit

SPEAKER

ANT

OFF

AUX IN 1

POWER

AC 120V~ 60Hz

Red wire

Left Speaker

LOCATION OF CONTROLS

MAIN UNIT

AUX IN 2

INDICATOR

EQ SOURCE VOL- VOL+

POWER

TUNE+

ANT

AUX IN 1

TUNE-

SPEAKER

OFF

POWER

AUX IN 2

INDICATOR

EQ SOURCE VOL- VOL+

TUNE-

9876

POWER

12 13

OFF

ANT

AUX IN 1

TUNE+

Indicator

AUX IN 2 jack

Remote Sensor

VOL+ (Volume Up) button

/ TUNE + button

VOL- (Volume Down) button

TUNE - button

(Play/Pause) button

SOURCE button

(Power) button

10.

EQ (Equalizer) button

11.

12.

FM Antenna

AUX IN 1 jacks

13.

POWER ON /OFF switch

14.

AC 120V~ 60Hz

LOCATION OF CONTROLS

REMOTE CONTROL

1. POWER button

2. /TUNE - button

3. VOL (Volume)+/- buttons

4. SOURCE button

5 6

5. (Mute) button

6. / TUNE+ button

7. (Play/Pause) button

8. EQ (Equalizer) button

BATTERY INSTALLATION--- REMOTE CONTROL

-First Time Use Remove and discard the insulation tab from the battery tray as figure on the right.

-Replacing Batteries For Remote Control

1. Push and slide out the battery holder as figure 1 below.

2. Replace the battery with a new CR2025 button cell markings on the rear of the Remote Control.

3. Close the battery holder.

Fig.1 Fig.2 Fig.3

%$77(5<35(&$87,216

as the polarity

EFFECTIVE DISTANCE OF REMOTE TRANSMITTER

Remote Sensor (on the

front of the main unit)

AUX IN 2

INDICATOR

EQ SOURCE VOL- VOL+

POWER

TUNE+

TUNE-

Approx.15 feet

POWER SOURCE

Insert the AC plug into a conveniently located AC outlet having AC 120V~ ; 60Hz.

NOTE: The AC plug supplied with the unit is polarized to help minimize the

possibility of electric shock. If the AC plug dose not fit into a AC outlet, do not file or cut the wide blade. It is the

have an electrician replacing the

obsolete outlet.

user's responsibility to

non polarized

GENERAL OPERATIONS

1. Insert the plug from AC Power Cord into AC wall outlet having AC 120V~ ; 60Hz.

2. Press the Power ON/OFF switch on the rear of the Main Unit to ON position.The Red Indicator will light. unit

3. Press the SOURCE button repeatedly to switch to desired mode.The indicator will turn to the

corresponding color as below:

~ Green: Radio ~ Blue: Bluetooth ~ Purple: AUX IN 1 ~ Orange: AUX IN 2

4. During Playback:

~ Press the VOL (Volume) +/- buttons to adjust volume level as desired. ~ Press the EQ button repeatedly to select and set equalizer mode as to Jazz; Pop; Classic or Rock.

as desire. ( .) ~ Press the (Mute) button on the Remote Control to turn off the sound. Press again to resume.

5. When finished listening, press the Power button to .

Then press the Power button on the Main Unit or Remote Control to power on the

Standby mode.

from

To reset the EQ to normal mode, power Off then power On the unit

turn the unit to Power Off (Standby) mode.

NOTE:

If long period of time will not use the unit, shut off the unit by press the POWER ON/OFF switch on the rear of main unit to OFF position

or unplug the AC Cord from wall outlet.

LISTEN TO FM RADIO

1. Power ON the unit as previous procedures.

2. Press the SOURCE button repeatedly until the color of Indicator changes to Green.

3. Press and hold the /TUNE - or /TUNE + buttons until the indicator starts blinking. The unit will start to search next (or previous) available FM radio station then plays.

4. Repeat the same procedures until the desired radio station is received. NOTE: If the received FM station is in stereo mode, the unit will play it in stereo mode automatically.

FM Antenna

The Antenna wire on the rear of Main Unit is for radio reception. If reception is weak, unwind and extend the wire or relocate the wire to improve the radio reception.

LISTEN TO TV/DVD/VCR/DVR

Audio out jacks on

TV/DVD/ VCR/DVR

Red

X IN 1

White

AUX I N 1

A UX IN 1

N 1

SPEAKER

ANT

OFF

AUX IN 1

POWER

AC 120V~ 60Hz

DVD

1. Connect one end of supplied RCA audio connection cable to the AUX IN 1 jacks on the rear of the unit as the figure above.

2. Connect the other end to the Audio out jacks on the external player (such as Television, VCR, DVD

Player, DVR ... etc.).

3. Power ON the unit as previous procedures.

4. Press the SOURCE button repeatedly until the color of Indicator changes to Purple.

5. Plays the music in the external player as usual. (Make sure the volume output level of the player is

in high level. Otherwise, sound from this unit is weak).

LISTEN TO EXTERNAL AUDIO DEVICES

AUX IN 2

AUX IN 2 jack

AUX IN 2

INDICATOR

AUX IN 2

INDICATOR

EQ SOURCE VOL- VOL+

TUNE+

TUNE-

1. Connect one end of supplied audio connection cable to the AUX IN 2 jack on the top of the unit as the figure above.

2. Connect the other end to the Audio out/Line out/Phone jack on the external player (such like iPod, iPhone, iPad, MP3 Player, Discman... etc.).

3. Power ON the unit as previous procedures.

4. Press the SOURCE button repeatedly until the color of Indicator changes to Orange.

5. Plays the music in the external player as usual. (Make sure the volume output level of the player

is in high level. Otherwise, sound from this unit is weak).

INDICATOR

SOURCE

VOL- VOL+

TUNE+

TUNE-

BLUETOOTH PARING AND PLAYBACK

1. Power ON the unit as previous procedures.

2. Press the SOURCE button on the unit or remote control until the indicator changes to Blue.

3. Turn on the BT function on the external BT device and play the music as usual. (Make sure the volume level of the external BT device is set to high level).

4. During palyback: Press the VOL (Volume) +/- buttons to adjust volume level.

Press the / TUNE- or / TUNE + button to skip track.

Press the (Play/Pause) button to pause. Press again to resume normal playback.

NOTES:

In first time use, pairing the external BT device as below: A. Power ON the unit as previous procedures, press the SOURCE button repeatedly until the

indicator turns to Blue and blinking.

B. Power ON the external BT player and enter to searching mode. Start pairing as the on screen

instructions on the external BT Player (For details pairing procedures, please refer to the user’s manual of your BT device.).

C. When the external BT player searched the Speaker, our model number “CHT914C” will appear on

the display of external BT device. Pairing code “0000” may need to enter.

TROUBLESHOOTING GUIDE

&KHFNWKHIROORZLQJVEHIRUHUHTXHVWLQJVHUYLFH

6<03720 3266,%/(&$86( 3266,%/(628/7,21

No power

No sound

Sound distortion

Remote not working

Bluetooth reception failure

AC plug not connected to the wall outlet

Volume in minimum position

The connected device is not in payback mode

Input source incorrect

Bass level of the connected device too high

Volume level too high

The battery is

The external device is far from the unit

Have not paired

consumed

Plug to the wall outlet.

Raise volume level by pressing the VOL (Volume) + button

Play the music/movie in the connected device as usual

volume level of it is in high level

Press the SOURCE button repeatedly to

set the input source to the desired mode

Reduce the bass level of the connected device

Reduce the volume level by pressing

the

VOL (Volume ) - button

Replace with new battery

Put the external BT device close to the

unit

Pair both unit as BT pairing page

and make sure the

GENERAL SPECIFICATIONS

Power Source.......................................................................................................... AC 120V~60Hz

Power Consumption...................................................................................................................45W

Radio Coverage ...............................................................................................FM 87.5 -108.0 MH

Impedance of Speakers:

Loud Speakers........................................................................................................

Tweeters...................................................................................................................

Bluetooth Effective Range.............................................................................................Up to 30 feet

(Measured in open area. Wall and structures may affect the effective range.)

Remote Effective Range...............................................................................................Up to 15 feet

$FFHVVRULHV

1 x User Manual

1 x Remote Control 1 x CR 2025 Button Cell (For Remote Control, already installed)

1 x Stereo Audio Connection Cable with 3.5mm stereo plug 1 x RCA cable

4 x Assembly Screws / Washers 2 x Wooden Bases

8 Ohm, 10W x 2

8 Ohm, 5W x 2

LIMITED WARRANTY

Craig warrants this product to be free from manufacturing defects in material and workmanship under normal use for a period of 90 days from date of purchase. If service is required, please return the product to the store where it was purchased for exchange; or, pack the unit in the original packing material with all accessories if applicable, a copy of your sales receipt and a Cashier’s check or Money Order for $15.00 (to cover shipping and handling costs) payable to Craig Electronics Inc. For consumers in Canada, please make sure that the cashier check or money order is redeemable through a U.S. bank. Ship your product freight pre-paid. Your unit will be repaired, replaced or if the unit can not be repaired or replaced, a refund will be forwarded to you within four weeks of receipt of your unit. Please ship your unit to:

Craig Electronics Inc.

1160 NW 163 Drive

Miami, Fl 33169

This warranty is void if the product has been: a) Used in a commercial application or rental. b) Damaged through misuse, negligence, or abuse. c) Modified or repaired by anyone other than an authorized Craig service center. d) Damaged because it is improperly connected to any other equipment. Note: This warranty does not cover: a) Ordinary adjustments as outlined in the Owner’s Manual which can be performed by the customer. b) Damage to equipment not properly connected to the product. c) Any cost incurred in shipping the product for repair. d) Damage to the product not used in the USA.

This warranty is not transferable and only applies to the original purchase. Any implied warranties, including the warranty of merchantability, are limited in duration to the period of this expressed warranty and no warranty whether expressed or implied shall apply to the product thereafter.

Under no circumstance shall Craig be liable for any loss or consequential damage arising out of the use of this product. This warranty gives specific legal rights. However, you may have other rights which may vary from state to state. Some states do not allow limitations on implied warranties or exclusion of consequential damage. Therefore, these restrictions may not apply to you.

To Obtain Service on your Product

email:service@craigelectronics.com

Printed in China CHT914c_WC_E0CL1_V0US

Size: 148.5(W) x 210(H)mm (A5)

FCC STATEMENT

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.　 Increase the separation between the equipment and receiver.　 Connect the equipment into an outlet on a circuit different from that to which the 　

receiver is connected.

Consult the dealer or an e　 xperienced radio/TV technician for help.

Junlan Electronic CHT914C User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual