Junlan Electronic CAB29610 User Manual

V130626

FRONT

1. Play/Pause

2. Pair Button

3. Volume -

4. Volume +

5. LED Indicator

BACK

BATTERY CHARGING

This speaker is powered by the internal rechargeable battery. When the battery

is nearly exhausted, a red indicator will light and ﬂash, the speaker should be

charged as soon as possible. Connect the unit with USB cable to the USB charge port, and the red indicator will turn solid red while charging. When charging is completed, the red indicator will turn off.

NOTE:

--A complete charge takes about 2 hours.

--The battery will charge whether the speaker is switched on or off.

BLUETOOTH

Pairing and connection

1. Move the Power On/Off to the ON position. Blue light will be on.

2. Press the PAIR button on the front of the unit, the blue indicator will ﬂash

quickly and enter pairing mode.

3. Please make sure your Bluetooth connection is activated on your device. Each Bluetooth device is different so refer to your device’s operating manual if you are unsure how to activate your Bluetooth connection. During searching,

the blue indicator will keep ﬂashing. The Bluetooth device will scan for the unit

and identify it as ITSB-203B. Select ITSB-203B on your Bluetooth device to connect.

4. When connected, the speaker will beep and the blue indicator will be solid. NOTE:

--Make sure to disconnect the AUX IN cable before Bluetooth pairing.

--If the device asks to input a password during paring, please enter 0000.

--If the device is unable to connect with the speaker, turn off the speaker, then turn on and reconnect again.

6. Power ON/OFF Switch

7. USB Charge Port

8. AUX IN Jack

OFFON

USB CHAR GEPOWER

AUX IN

6. 7. 8.

During playback:

--Press + and - buttons to adjust the volume level.

--During playback, press play/pause button to pause and press again to resume.

NOTE:

--Play/Pause functions may not work with all Bluetooth devices.

--When the AUX IN cable is connected, the AUX IN source will be selected and there will be no audio output from Bluetooth source.

Innovative Technology Electronics Corp. 1 Channel Drive, Port Washington, NY 11050 Toll free: 1-877-483-2497 Website for support: www.ithomeproducts.com/support

There are no express warranties except as listed above. REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE

EXCLUSIVE REMEDY OF THE CUSTOMER, (IT) SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY.

Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you. This warranty gives

you speciﬁc legal rights and you may also have other rights, which vary from

state to state.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.　 Increase the separation between the equipment and receiver.　 Connect the equipment into an outlet on a circuit different from that to which the 　

receiver is connected.

Consult the dealer or an e　 xperienced radio/TV technician for help.