Juniper PowerConnect J-SRX210, SRX210, SRX210B, SRX210H, SRX210H-POE Quick Start Manual

SRX210 Services Gateway Quick Start

g031132

g031113

Use the instructions in this quick start to help you connect the SRX210 Services
Gateway to your network. For details, see the SRX210 Services Gateway Hardware
Guide at http://www.juniper.net/techpubs/a057.html

.

SRX210 Services Gateway Front Panel

Callout Description Callout Description

1 Mini-PIM slot 5 USB ports

2 Power button 6 Console port

3 LEDs (ALARM, POWER,

STATUS, HA, mPIM, EXPCARD)

4 Reset Config button

7 Gigabit Ethernet (0/0 and 0/1) and Fast

Ethernet (0/2 to 0/7) ports

SRX210 Services Gateway Back Panel

SRX210 Services Gateway Models

The following models of SRX210 Services Gateways are available:

Device DDR Memory Power over

SRX210B 512 MB No

SRX210H 1 GB No

SRX210H-POE 1 GB Yes

SRX210BE 512 MB No

SRX210HE 1 GB No

SRX210HE-POE 1 GB Ye s

SRX210HE-TAA 1 GB No

SRX210HE-POE-TAA 1 GB Ye s

On the SRX210H-POE, SRX210HE-POE and SRX210HE-POE-TAA models, Power
over Ethernet (PoE) of 50 watts is supported across four ports (0/0, 0/1, 0/2, and 0/3).

Note that you must use the following power supply adapters (supplied) for your services
gateway:

 54V, 150 watts power supply adapters for PoE models

 12V, 60 watts power supply adapters for non-PoE models

Connecting and Configuring the SRX Series Device

Follow the instructions to connect and set up the SRX210 Services Gateway to protect
your network. Refer to the LEDs on the front of the device to help you determine the
status of the device.

Ethernet

Callout Description Callout Description

1 Power supply input 4 Lock for security cable

2 Cable tie holder 5 ExpressCard slot

3 Grounding point

Overview

The SRX210 Services Gateway is a security device that requires the following basic
configuration settings to function:

 Interfaces must be assigned IP addresses.

 Interfaces must be bound to zones.

 Policies must be configured between zones to permit or deny traffic.

 Source NAT rules must be set.

The device has the following default configuration set when you power it on for the first
time. To use the device, you do not need to perform any initial configuration.

Factory-Default Settings for Initial Configuration:

g031118

Port Label Interface Security

0/0 ge-0/0/0 untrust client unassigned

0/1 and 0/2
to 0/7

ge-0/0/1 and
fe-0/0/2 to
fe-0/0/7

Zones

trust server 192.168.1.1/24

DHCP State IP Address

Factory-Default Settings for Security Policies:

Source Zone Destination Zone Policy Action

trust untrust permit

trust trust permit

untrust trust deny

Factory-Default Settings for NAT Rule:

Source Zone Destination Zone Policy Action

trust untrust source NAT to untrust zone

interface

NOTE: Source NAT translates the source address for packets coming from any number
of hosts on a private network to one public IP address.

Task 1: Connect the Power Cable and a Power Source

Connect the power cable to the device and a power source. We recommend using a
surge protector. Note the following indications:

 POWER LED (green): The device is receiving power.

 STATUS LED (green): The device is operating normally.

 ALARM LED (amber): The device is operating normally, and may glow amber

because a rescue configuration has not been set. This is not a panic condition.

 mPIM LED (off): The Mini-Physical Interface Module (Mini-PIM) is not present or is

not detected by the device. If this LED is green and steadily on, it indicates that the
Mini-PIM is functioning normally.

NOTE: After a rescue configuration has been set, an amber ALARM LED indicates a
minor alarm, and a solid red ALARM LED indicates a major problem on the services
gateway.

NOTE: You must allow the device between 5 and 7 minutes to boot after you power it on.
Wait until the STATUS LED is solid green before proceeding to the next task.

Task 2: Connect the Management Device

Connect the management device to the services gateway, using either of the following
methods:

 Connect an RJ-45 cable (Ethernet cable) from one of the following ports on the front

panel to the Ethernet port on the management device (workstation or laptop):

 0/1 (interface ge-0/0/1)

 0/2 through 0/7 (interfaces fe-0/0/2 through fe-0/0/7)

We recommend this connection method. If you are using this method to connect,
proceed to Task 3.

 Connect an RJ-45 cable (Ethernet cable) from the port labeled CONSOLE to the

supplied DB-9 adapter, which then connects to the serial port on the management
device (serial port settings: 9600 8-N-1).

If you are using this method to connect, proceed with the CLI configuration
instructions in the Branch SRX Series Services Gateways Golden Configurations at
http://www.juniper.net/us/en/local/pdf/app-notes/3500153-en.pdf .

An illustration to connect a management interface.

Task 3: Ensure That the Management Device Acquires an IP Address

After you connect the management device to the services gateway, the DHCP server
process on the services gateway will assign an IP address automatically to the
management device. Ensure that the management device acquires an IP address on the

192.168.1.0/24 subnetwork (other than 192.168.1.1) from the services gateway.

NOTE: The services gateway functions as a DHCP server and will assign an IP address
to the management device.

NOTE: If an IP address is not assigned to the management device, manually configure
an IP address in the 192.168.1.0/24 subnetwork. Do not assign the 192.168.1.1 IP
address to the management device because this IP address is assigned to the services
gateway. By default, the DHCP server is enabled on the L3 VLAN interface, (IRB) vlan.0
(ge-0/0/1 and fe-0/0/2 to fe-0/0/7), which is configured with an IP address of

192.168.1.1/24.

NOTE: When an SRX210 Services Gateway is powered on for the first time, it boots
using the factory default configuration.

Task 4: Ensure That an IP Address Is Assigned to the Services Gateway

Use one of the following methods to obtain an IP address on the services gateway:

Page 2

 Method 1: Obtaining a Dynamic IP Address on Your Services Gateway

Use the port labeled 0/0 (interface ge-0/0/0) to connect to your Internet Service
Provider (ISP). Your ISP will assign an IP address using the DHCP process. If you
use this method, when you get to Task 6, skip Steps 1 through 4.

 Method 2: Obtaining a Static IP Address on Your Services Gateway

Use the port labeled 0/0 (interface ge-0/0/0) to connect to your ISP. Your ISP will
have provided a static IP address. You will not receive an IP address using the
DHCP process. If you use this method, you must configure the static IP address on
the services gateway as described in Task 6, Steps 1 through 4.

Task 5: Access the J-Web Interface

1. Launch a Web browser from the management device.

2. Enter http://192.168.1.1 in the browser address box. The J-Web login page
appears.

3. Specify the default username as root. Do not enter any value in the Password field.

4. Click Log In. The first time you log in, the J-Web Initial Setup page appears.

5. To begin configuring your services gateway, click the Start button in the lower right
corner of the page.

NOTE: All network and management access settings are optional.

If you have followed method 1 of Task 4 (Obtaining a Dynamic IP Address on Your
Services Gateway), you can skip all the other steps and go directly to Task 7.

If you have followed method 2 of Task 4 (Obtaining a Static IP Address on Your Services
Gateway), ensure that you make the following J-Web modifications:

1. On the Configure System: Network Settings page of the wizard, enter the IP address
of the device that connects your device with WAN (service provider) in the Default
Gateway field, and enter server names in the DNS Name Servers list. Your ISP
provides the IP address for the gateway and the server names.

2. On the Configure Interfaces page of the wizard, select the ge-0/0/0.0 interface and
click Edit.

3. On the Add/Edit interface page, next to Address, clear DHCP and select IP
Address.

4. In the IP Address/subnet field, enter the IP address provided by your ISP. The IP
address must be entered in a.b.c.d/xx format, where xx is the subnet prefix.

Task 6: Configure the Basic Settings

Configure the basic settings, such as hostname, domain name, and root password for
your services gateway.

IMPORTANT: Ensure that you have configured the IP address, root authentication,
and default gateway before you apply the configuration.

NOTE: All fields marked with an asterisk (*) are mandatory.

NOTE: To allow the required Inbound services and protocols to be terminated on the

Services Gateway, make sure you have selected the required services and protocols
under Services (Inbound) and Protocols (Inbound). Select all to permit all protocols
and services.

NOTE: You can use the Configure J-Web Preferences page of the wizard to set the
J-Web starting page options and J-Web commit options.

Task 7: Apply the Basic Configuration

On the last page (Review and Commit) of the wizard, review the basic configuration, and
click Commit to apply the configuration.

After you configure the basic settings, the J-Web Setup wizard redirects you to the
J-Web pages, where you can continue configuring the device.

Page 3

After you complete initial setup configuration, the Setup wizard is no longer available. To
make changes to the configuration, use the J-Web interface.

NOTE: To make any changes to the interface configuration, see the Branch SRX Series
Services Gateways Golden Configurations at

http://www.juniper.net/us/en/local/pdf/app-notes/3500153-en.pdf .

Task 8: Verify the Configuration

Access http://www.juniper.net to ensure that you are connected to the Internet. This
connectivity ensures that you can pass traffic through the services gateway.

NOTE: If the http://www.juniper.net page does not load, verify your configuration settings,
and ensure that you have applied the configuration.

After you complete these steps, you can pass traffic from any trust port to the untrust
port.

Powering Off the Device

You can power off the device in one of the following ways:

 Graceful shutdown—Press and immediately release the Power button. The device

begins gracefully shutting down the operating system.

 Forced shutdown—Press the Power button, and hold it for 10 seconds. The device

immediately shuts down. Press the Power button again to power on the device.

You can reboot or halt the system in the J-Web interface by selecting Maintain >

Reboot.

NOTE: Use the graceful shutdown method to halt, power off, or reboot the services

gateway. Use the forced shutdown method as a last resort to recover the services
gateway if the services gateway operating system is not responding to the graceful
shutdown method.

For additional configuration information, see the Branch SRX Series Services Gateways
Golden Configurations at
http://www.juniper.net/us/en/local/pdf/app-notes/3500153-en.pdf .

For detailed software configuration information, see the software documentation
available at http://www.juniper.net/techpubs/software/junos-srx/index.html .

NOTE: The Reset Config button is recessed to prevent it from being pressed
accidentally.

The rescue configuration is a previously committed, valid configuration. You must have
previously set the rescue configuration through the J-Web interface or the CLI.

To press the Reset Config button, insert a small probe (such as a straightened paper clip)
into the pinhole on the front panel.

 By default, pressing and quickly releasing the Reset Config button loads and

commits the rescue configuration through the J-Web interface or the CLI. The Status
LED is amber and steadily on during this time.

 By default, pressing and holding the Reset Config button for 15 seconds or

more--until the Status LED is amber and steadily on--deletes all configurations on
the device, including the backup configurations and rescue configuration, and loads
and commits the factory configuration.

For details about managing and monitoring your device, see the Junos OS
Administration Guide and the Junos OS CLI Reference Guide.

Contacting Juniper Networks

For technical support, see http://www.juniper.net/support/requesting-support.html .

Using the Reset Config Button

If a configuration fails or denies management access to the services gateway, you can
use the Reset Config button to restore the device to the factory default configuration or to
a rescue configuration. For example, if someone inadvertently commits a configuration
that denies management access to the services gateway, you can delete the invalid
configuration and replace it with a rescue configuration by pressing the Reset Config
button.

Juniper Networks, Junos, Steel-Belted Radius, NetScreen, and ScreenOS are registered trademarks of Juniper Networks, Inc. in the United States and other countries. The Juniper Networks Logo, the Junos logo, and JunosE are
trademarks of Juniper Networks, Inc. All other trademarks, service marks, registered trademarks, or registered service marks are the property of their respective owners. Juniper Networks assumes no responsibility for any inaccuracies
in this document. Juniper Networks reserves the right to change, modify, transfer, or otherwise revise this publication without notice. Products made or sold by Juniper Networks or components thereof might be covered by one or more
of the following patents that are owned by or licensed to Juniper Networks: U.S. Patent Nos. 5,473,599, 5,905,725, 5,909,440, 6,192,051, 6,333,650, 6,359,479, 6,406,312, 6,429,706, 6,459,579, 6,493,347, 6,538,518, 6,538,899,
6,552,918, 6,567,902, 6,578,186, and 6,590,785. Copyright © 2011, Juniper Networks, Inc. All rights reserved. Printed in USA. Part Number: 530-038122 Rev. 01, March 2011.