Juniper NETWORK AND SECURITY MANAGER NSMXPRESS - QUICK START REV1, NETWORK AND SECURITY MANAGER NSMXPRESS Quick Start Manual

Network and Security Manager NSMXpress Quick Start

November 17, 2010 Revision 1

NSMXpress isanappliance version of Network and Security Manager (NSM). NSMXpress simplifies the complexity of network administration by providing a single, integrated management interface that controls device parameters.

This robust hardware management system installs in minutes with full high availability (HA) support, making it easy to scale and deploy. Enterprise customers with limited resources can benefit significantly from NSMXpress because it eliminates the need to have dedicated resources for maintaining a network and security management solution.

NSMXpress makes it easy for administrators to control device configuration, network settings, and security policy settings for multiple families of Juniper devices including:

•

IDP Series Intrusion Detection and Prevention Appliances and Firewall and VPN devices running ScreenOS

•

Devices running Junos OS, such as J Series Services Routers, SRX Series Services Gateways, EX Series Ethernet Switches, M Series Multiservice Edge Routers, and MX Series Ethernet Services routers

•

SA Series SSL VPN Appliances

•

IC Series Unified Access Control Appliances

For a complete list of supported device families and platforms, see the Network and Security Manager Administration Guide.

Up to 10 administrators can log into NSMXpress concurrently.

This quick start explains the following steps for installing and configuring NSMXpress and for configuring NSM.

1. Install the NSMXpress appliance hardware.

2. Set up the NSMXpress appliance using the serial port.

NSMXpress Quick Start

3. Configure the NSMXpress software using the Web interface.

4. Configure the NSM software which is preinstalled onto the NSMXpress appliance,

with site-specific parameters.

Contents

Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

NSMXpress Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Installing the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Initial Setup Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Boot NSMXpress . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Set Up Your Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Web Interface Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Configuring the NSM Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Configuring Basic Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Configuring High Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Advanced Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Enabling and Configuring Remote Replication of the Database . . . . . . . 15

Enabling and Configuring SRS (Regional Server Only) . . . . . . . . . . . . . . . 16

Installing NSM Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Managing NSM Administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Changing the Superuser Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Downloading NSM MIBS (Regional Server Only) . . . . . . . . . . . . . . . . . . . . . . . 18

Exporting Audit Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Exporting Device Logs (Regional Server Only) . . . . . . . . . . . . . . . . . . . . . . . . . 18

Generating Reports (Regional Server Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Modifying NSM Configuration Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Backing Up the NSM Database . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Changing the NSM Management IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Scheduling Security Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Managing System Administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Rebooting or Shutting Down NSMXpress . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Changing the User Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Configuring the Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Network Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Routing and Gateways . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Hostname and DNS Clients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Host Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Managing RADIUS Servers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Adding a RADIUS Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Changing the Priority of RADIUS Servers . . . . . . . . . . . . . . . . . . . . . . . . . 27

Deleting a RADIUS Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Editing RADIUS Server Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Monitoring with SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

SNMP Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

SNMP System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

SNMP Trap Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Forwarding Syslog Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Viewing Syslog Receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Adding and Configuring Syslog Receivers . . . . . . . . . . . . . . . . . . . . . . . . . 32

Editing Syslog Receiver Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Deleting Syslog Receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Changing the System Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Installing Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Managing Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Creating New NSMXpress Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Deleting a User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Editing User Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Understanding User Profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Configuring the Web Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Maintaining NSMXpress . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Viewing System Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Log Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

CPU Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Memory Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Network Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Process Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Disk Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Tile All Graphs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Upgrading the Recovery Partition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Auditing User Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Error Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Network Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Ping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Traceroute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Lookup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

IP Subnet Calculator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Tech Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Viewing System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

List of Technical Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Requesting Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Self-Help Online Tools and Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Opening a Case with JTAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

NSMXpress Quick Start

Hardware Installation

We recommend that you install NSMXpress on your LAN to ensure that it can communicate with your applicable resources,such as authentication servers, DNS servers, internal Web servers through HTTP/HTTPS, external Web sites through HTTP/HTTPS (optional), the Juniper update server via HTTP, Network File System (NFS) file servers (optional), and client/server applications (optional).

NSMXpress Ports

Table 1 on page 4 provides required port information on the NSMXpress.

Table 1: Required Ports on NSMXpress

NOTE: If you decide to install NSMXpress in your DMZ, ensure that it can connect to your internal resources.

443

8443

7800

7801

7802

7803

7804

Depends on ConfigurationInternetLANDescriptionPortDirection

NoNoYesSSH command-line management22In

NoNoYesWeb interface for administrator

YesYesLANWebinterfacefor listening for NSM

API messages.

NoYesYesConnections from managed

devices to NSMXpress

NoNoYesConnections from the NSM GUI

Client to NSM

YesNoYesHeartbeat between peers in an HA

cluster

YesYesYesConnections from managed IDP

devices to NSM

YesYesYesConnections from devices running Junos , Secure Access devices, or Infranet Controller devices

Table 1: Required Ports on NSMXpress (continued)

Hardware Installation

Depends on

ConfigurationInternetLANDescriptionPortDirection

For more information on ports, refer to the Network and Security Manager Installation Guide.

Installing the Hardware

Follow these steps to unpack the NSMXpress appliance and connect it to your network.

To install NSMXpress:

22Out

123

NoYesYesSSH connection to new managed device

YesNoYesTelnet connection to new managed device

NoNoYesDNS lookups53

YesYesNoSystem Security Updates from Juniper Networks

YesNoYesShared Disk portmap lookup111

YesYesYesNetworkTime Protocol (NTP) time synchronization

YesNoYesShared Disk NFS connection2049

1. Place the shipping container on a flat surface and remove the hardware components

with care.

2. Remove the NSMXpress device from the shipping container and place it on a flat

surface.

3. Mount NSMXpress in your server rack using the attached mounting brackets.

4. Plug the power cord into the AC receptacle on the rear panel.

If your NSMXpress contains two power supplies, plug a power cord into each AC receptacle.

5. Plug the other end of the power cord into a wall socket.

If your NSMXpress contains two power supplies, plug each power cord into a separate power circuit to ensure that the NSMXpress continues to receive power if one of the power circuits fails.

6. Plug the Ethernet cable into the port marked ETH0 on the front panel. See Figure 1 on

page 6.

NSMXpress Quick Start

Figure 1: Front Panel of NSMXpress

7. Plug the null modem serial cable into the console port. See Figure 1 on page 6.

This cable was shipped with your NSMXpress. If you do not have this cable, use any other null modem serial cable.

8. Push the power button in the upper left corner of the front panel.

The green LED below the power button turns on. The NSMXpress hard disk LED turns on whenever the appliance reads data from or writes data to an NSMXpress hard disk.

The internal port uses two LEDs to indicate the LAN connection status, which is described in Table 2 on page 6.

Hardware installation is now complete. The next step is to set up the software, as described in “Initial Setup Configuration” on page 6.

Table 2 on page 6 provides LED information for the ETH0 and ETH1 ports.

Table 2: Ethernet Port LEDs

Initial Setup Configuration

When you first turn on an unconfigured NSMXpress appliance, you need to enter basic network and machine information through the serial console to make your appliance accessible to the network. After entering these settings, you can continue configuring the appliance using the CLI or the Web interface. You are not prompted for the initial setup information again.

LED2LED 1LAN Status

OffOff10 Mbps connection

OffGreen100 Mbps connection

OffOrange1000 Mbps connection

BlinkingOrange, Green, or OffData is being transferred

OffOffNo connection

Boot NSMXpress

Initial Setup Configuration

This section describes the required serial console setup and the tasks you need to perform when connecting to your NSMXpress for the first time:

•

Boot NSMXpress on page 7

•

Set Up Your Appliance on page 7

To configure NSMXpress for the first time, you must attach your NSMXpress appliance to a console terminal running an emulation utility such as HyperTerminal.

1. Configure a console terminal or terminal emulation utility to use the following serial

connection parameters:

•

9600 bits per second

•

8-bit no parity (8N1)

•

1 stop bit

•

No flow control

Set Up Your Appliance

2. Connect the terminal or laptop to the null modem serial cable plugged into the

NSMXpress console port.

3. Turn on the NSMXpress appliance.

When NSMXpress is powered on, the serial console displays diagnostic information beforeproceeding to the boot countdown. When complete,the serial console displays the login prompt terminal emulator.

NSMXpress.juniper.net login:

4. Enter admin as your default login name.

5. Enter abc123 as your default password.

6. Change your default password when prompted. Enter the default password first,

followed by your new password. All passwords are case-sensitive.

This section provides the minimum information necessary to make your appliance active on the network.

To set up your appliance either as a regional server or a central manager, follow these steps:

1. Enter the IP address for interface eth0 and press Enter.

2. Enter the subnet mask for interface eth0 and press Enter.

3. Enter the default route or default gateway address for interface eth0 and press Enter.

NSMXpress Quick Start

Your NSMXpress is now active on the network. To configure your system via a web browser, connect to: https://10.150.43.205/admin

To configure your system via command line, type: nsm_setup

For operation of NSM server, switch to user “nsm”. Please consult NSM product documentation for details.

[admin@NSMXpress ~]$

To configure the NSM software using the CLI, see the NSMXpress User Guide. To configure the NSM software using the Web interface, go to “Web Interface Configuration” on page 8.

Web Interface Configuration

To configure NSM on your system from a Web interface, use the following steps.

1. Copy the URL (starting with https://) from the terminal emulator after installing

NSMXpress:

Your NSMXpress is now active on the network. To configure your system via a web browser, connect to: https//10.150.43.205/administration

2. Open a Web browser and paste the URL into the address text box.

3. Press Enter to open the NSMXpress login page.

4. Enter the admin user name and password and then click Login.

5. See “Configuring the NSM Software” on page 8 for details about how to install and

configure NSM on your NSMXpress appliance from the Web interface.

Configuring the NSM Software

After logging in as an ‘admin’ user, an initial setup script walks you through additional configurationsystemsettings before finalizing the NSM installation. This chapter describes that setup process.

Your NSMXpress appliance comes preconfigured as a regional server or a central manager. Most installation and configuration steps in this section are identical for both types of server. All exceptions are noted.

After logging into the NSMXpress Web interface, NSMXpress provides you with the following installation options:

•

Configuring Basic Settings on page 9

•

Configuring High Availability on page 11

•

Advanced Options on page 14

•

Installing NSM Software on page 17

Configuring Basic Settings

To install the regional server or central manager software using the minimum requirements:

1. Install your NSMXpress hardware as described in “Hardware Installation” on page 4.

2. Boot and setup your NSMXpress appliance as described in “Initial Setup Configuration”

on page 6.

3. Enter the https://<ip>/administration URL for your appliance in a Web browser. See

“Web Interface Configuration” on page 8 for details.

Configuring the NSM Software

4. Log into the Web interface. The System Info page opens.

5. Click the link Install NSM Regional Server (see Figure 2 on page 10) to go to the Install

Regional Server window or click the Install NSM Central Manager link to view the Install NSM Central Manager window (see Figure 3 on page 10), as the case may be.

NOTE: The “admin” user default username is admin and the password is

the one you created in Step 6 of “Boot NSMXpress” on page 7.

NSMXpress Quick Start

Figure 2: Regional Server Configuration Main Menu

Figure 3: Central Manager Configuration Main Menu

Configuring the NSM Software

6. Enter the primary IP address of your management server for eth0 (the default).

You can use the default IP address next to the first radio button or select the second radio button and then enter a different IP address. Each IP address you add (in addition to the default IP address) will be available in the drop-down list after you click the second radio button.

7. Enter the NSM superuser password in the top text box, and then reenter it in the text

box below it.

This password must be at least eight characters long and is case-sensitive. This password is used by the NSM superuser (also referred to as the NSM administrator). This user has the highest level of privileges in NSM.

8. Enter the GUI Server one-time password in the top text box, and then reenter it in the

text box below it. This password is used to authenticate this NSM server with other NSM servers with which it communicates. Regional servers use this password to authenticate peer servers in an HA configuration and to authenticate the central manager. The central manager uses this password to authenticate its peer server in an HA configuration and any regional servers it manages. NSM servers must have the same GUI Server one-time password, or the authentication will fail.

9. Select the license option. (This option is available only for regional servers.)

a. Select Base Install to use the built-in limited device license for as many as 25

devices.

b. Click Upload license file to upload the license file you generated using the Juniper

License Management System (LMS), which permits you to manage more than 25 devices. This license file must be located on your local hard drive.

See the Network and Security Manager installationGuide for more information about NSM licensing.

10. Click Submit to save any changes, and then click Install to install the software.

Configuring High Availability

To configure high availability (HA) settings:

NSMXpress Quick Start

1. On the NSM Configuration Main Menu, click Menu next to High Availability to access

HA options. See Figure 4 on page 12.

Figure 4: High Availability Options

2. Use the High Availability option to turn HA on (y) or off (n). The default is off.

3. Use the Primary Status option to set your NSMXpress appliance as either the primary

or secondary server in the HA cluster. If you select y, it is the primary server (the default). If you select n, it is the secondary server.

4. Use the HA Remote IP option to enter the IP address for the HA peer in the HA cluster.

5. Use the HA Link Failure Detection IP option to enter the IP address of a computer

outside the HA cluster that you can ping to verify connection status.

6. Use the HA Inter-server password option to enter the heartbeat password used between

the primary and secondary servers.

7. Click Submit to save the changes.

8. Click Menu next to Shared Disk (see Figure 4 on page 12) to configure a shared disk

for regional servers (see Figure 5 on page 13) or for central managers (see Figure 6 on page 13). This step is optional.

Figure 5: Shared Disk Options for Regional Servers

Figure 6: Shared Disk Options for Central Managers

Configuring the NSM Software

NSMXpress supports shared disk via NFS only. Due to the data-intensive nature of NSM, we recommend gigabit speed links (1000 Mbps) for shared disk use. For more information about custom settings, refer to the Network and Security Manager Installation Guide.

9. Click Menu next to HA Links (see Figure 4 on page 12) to configure the second link in

the HA cluster (see Figure 7 on page 13). This step is optional.

Figure 7: HA Links Options

Use the options in this menu to set up a redundant link for the HA cluster. If you are going to use a second link, you need to set the IP address for eth1 before configuring this setting (see “Configuring the Network” on page 23 for details). Setting a redundant link is optional. For more information about custom settings, refer to the Network and Security Manager Installation Guide.

If you configure HA with just one heartbeat link, then device management traffic and data replication traffic both use that link. If you configure two links, device management traffic uses the first link and data replication uses the second.

NSMXpress Quick Start

If you set the HA link count to 2, an expanded menu appears to configure the second link:

Figure 8: Redundant Links

10. Click Menu next to HA Advanced Settings (see Figure 4 on page 12) to configure HA

advanced settings (see Figure 9 on page 14). This step is optional.

For more information about custom settings, referto the Network and Security Manager Installation Guide.

Advanced Options

Figure 9: HA Advanced Settings

11. Click Submit to save the HA options and return to the NSM Configuration Main Menu.

To display the Advanced Options menu, on the NSM Configuration Main Menu, select Menu next to Advanced Options. The Advanced Options menu appears as shown in Figure 10 on page 14.

Figure 10: Advanced Options Menu

Advanced installation options include:

Configuring the NSM Software

•

https port for NBI service—Allows you to configure a port to listen for messages for the NSM API. By default, this value is 8443. You can configure it to any port number from 1025 to 65535.

•

Remote Replication of Database—Mirrors the daily backup to an external server. You can toggle it on or off. After you turn it on, use the menu options to configure this option.

•

SRS Enabled Options (regional server only)—Opens a menu to enable and configure the Statistical Report Server (SRS). These options enable NSMXpress to interface with SRS. You can toggle it on or off. When it is on, a menu with additional options is available.

NOTE: SRS must be installed on a separate server from NSM.

The following sections provide details about the remote replication and SRS options:

•

Enabling and Configuring Remote Replication of the Database on page 15

•

Enabling and Configuring SRS (Regional Server Only) on page 16

Enabling and Configuring Remote Replication of the Database

To configure remote replication of database settings:

1. On the Advanced Options menu, click Menu next to Remote Replication of Database

(see Figure 4 on page 12) to configure daily backups (see Figure 11 on page 15).

Figure 11: Remote Replication of Database Options

2. Use the Remote Replication of Database option to turn remote replication on (y) or

off (n). The default is off.

3. Use the Hour of day to Replicate Database option to start the backup. The valid range

(in hours) is 00 through 23. The default is 2 AM.

4. Use the Remote Backup IP option to enter the IP address of the remote backup server.

Backup information is copied to the /var/netscreen/dbbackup directory on the remote server. The “nsm” user must exist on both servers and you must establish an SSH trust relationship. See the Network and Security Manager Installation Guide, for details.

NSMXpress Quick Start

5. Use the Remote Replication Timeout option to set up a timeout for Rsync. The valid

range (in seconds) is 1-65535. The default is 1800 seconds.

6. Click Submit to save the options and return to the main menu or continue with the

other advanced installation options.

Enabling and Configuring SRS (Regional Server Only)

This option is not available on a central manager. To configure statistical report server (SRS) settings:

1. On the Advanced Options menu, click Menu next to SRS (see Figure 4 on page 12) to

open the SRS menu (see Figure 12 on page 16).

Figure 12: SRS Menu

2. Use the SRS options to turn SRS on (y) or off (n). The default is off. If you turn on this

feature, the server is used with the GUI server.

3. Use the SRS DB IP option to enter the IP address for the server on which you have

installed the SRS database server.

4. Use the SRS DB Type option to select the database type. The values are pgsql (the

default), oracle, or mssql.

5. Use the SRS Database Name option to enter the name of the SRS database. The

default value is netscreen. To enter another name, click the radio button next to the blank text box and enter the name in the text box.

6. Use the SRS DB Owner Name option to enter the owner’s name of the SRS database.

The default value is netscreen. To enter another name, click the radio button next to the blank text box and enter the name in the text box.

7. Use the SRS Database Owner Password option to enter the SRS database password.

The password requires a minimum of eight characters and is case-sensitive. Reenter it in the second text box.

8. Click Submit to save the options and return to the NSM Configuration Main Menu.

Installing NSM Software

After you submit all your configuration options, click Install to install the NSM software on your NSMXpress appliance. Installation takes a few minutes. A status indicator shows the progress of the installation. Wait until installation is finished before continuing to use the Web interface.

Managing NSM Administration

Expand NSM Administration in the left navigation tree to access the options described in this section. These options are available only after installing NSM.

The following sections explain how to use each of the NSM Administration options:

Managing NSM Administration

•

Changing the Superuser Password on page 17

•

Downloading NSM MIBS (Regional Server Only) on page 18

•

Exporting Audit Logs on page 18

•

Exporting Device Logs (Regional Server Only) on page 18

•

Generating Reports (Regional Server Only) on page 19

•

Modifying NSM Configuration Files on page 19

•

Backing Up the NSM Database on page 20

•

Changing the NSM Management IP on page 21

•

Scheduling Security Updates on page 21

Changing the Superuser Password

To change the superuser password, select NSM Administration > NSM Super User Password. See Figure 13 on page 17.

Figure 13: Change Superuser Password

NSMXpress Quick Start

Downloading NSM MIBS (Regional Server Only)

To download any available MIBs, select NSM Administration > Download NSM MIBS, and then click Download MIB. See Figure 14 on page 18. This option is not available on the central manager.

Figure 14: Download NSM MIBs

Exporting Audit Logs

To export audit logs, select NSM Administration > Export Audit Logs. See Figure 15 on page 18.

Figure 15: Export Audit Logs

To export an audit log to a csv file, select csv in the drop-down list box, and then enter the csv file name in the text box.

To export an audit log to a system log server, select syslog in the drop-down list box, and then enter the server IP address, if it is not the local host.

Exporting Device Logs (Regional Server Only)

To export device logs, select NSM Administration > Export Device Logs. See Figure 16 on page 18. This option is not available on the central manager.

Figure 16: Export Device Logs

Generating Reports (Regional Server Only)

To generate reports, select NSM Administration > Generate Reports. See Figure 17 on page 19. This option is not available on the central manager.

Figure 17: Generate Reports

Managing NSM Administration

NOTE: The user is an NSM administrator and not an NSMXpress user. Enter

a user name as domain/user, such as global/super.

Modifying NSM Configuration Files

To manually edit the GuiSrv.cfg, DevSvr.dfg and HaSvr.cfgfiles, select NSM Administration > Modify NSM ConfigurationFiles. The example in Figure 18 on page 20, shows the option

to modify the GuiSvr.cfg file.

NSMXpress Quick Start

Figure 18: NSM Configuration Files

Backing Up the NSM Database

To configure backups of the NSM database, select NSM Administration > NSM Database Backup link under NSM Administration. See Figure 19 on page 21.

NOTE: If you subsequently change the NSMXpress configuration by using the nsm-setup utility, all manual changes to the configuration files are lost.

Figure 19: Database Backup

Managing NSM Administration

Changing the NSM Management IP

To change the IP address of the NSM management server, select NSM Administration > NSM Management IP link under NSM Administration. See Figure 20 on page 21.

Figure 20: Change Management IP

Scheduling Security Updates

To schedule security updates, select NSM Administration > Schedule Security Updates. See Figure 21 on page 22.

NSMXpress Quick Start

Figure 21: Schedule Security Updates

Managing System Administration

Use the options in the System Administration section to perform the tasks described in the following sections:

•

Rebooting or Shutting Down NSMXpress on page 22

•

Changing the User Password on page 23

•

Configuring the Network on page 23

•

Managing RADIUS Servers on page 25

•

Monitoring with SNMP on page 28

•

Forwarding Syslog Messages on page 31

•

Changing the System Time on page 34

•

Installing Updates on page 34

•

Managing Users on page 35

•

Configuring the Web Interface on page 39

Rebooting or Shutting Down NSMXpress

To reboot or shut down NSMXpress, select System Administration > Bootup and Shutdown, and then click either Reboot System or Shutdown System. See Figure 22

on page 22.

Figure 22: ReBoot or Shut Down

Changing the User Password

To change the user password, select System Administration > Change User Password, fill out the form shown in Figure 23 on page 23, and then click Change.

Figure 23: Change User Password

Configuring the Network

To access options that allow you to configure the network, select System Administration > Network Configuration.The Network Configurationwindow appears as shown in Figure

24 on page 23.

Managing System Administration

Figure 24: Network Interfaces Options

The following sections describe each of the options available in the Network Configuration window:

•

Network Interfaces on page 23

•

Routing and Gateways on page 24

•

Hostname and DNS Clients on page 24

•

Host Addresses on page 25

Network Interfaces

Use this option to manage the network interfaces. See Figure 25 on page 24.

NSMXpress Quick Start

Figure 25: Network Interfaces

Routing and Gateways

Use this option to configure and manage routes and gateways. See Figure 26 on page 24.

Figure 26: Routes and Gateways

Hostname and DNS Clients

Use this option to configure and manage hostnames and DNS clients. See Figure 27 on page 25.

Managing System Administration

Figure 27: DNS Client Options

Host Addresses

Use this option to manage host addresses, See Figure 28 on page 25.

Figure 28: Host Address

Managing RADIUS Servers

The NSMXPress WebUI supports authentication of users defined in the RADIUS servers, in addition to authentication of locally defined admin users.

When a user logs into NSMXpress using the WebUI, the software first checks the UNIX user database and then the WebUI user database to authenticate the user. If the user is not a locally defined admin user, the software contacts the RADIUS servers added to the RADIUS server list in the Web UI to authenticate the user. The RADIUS servers are contactedin the order of priority set in the RADIUS server list. If any of the RADIUS servers authenticates the user, the user is logged in with the privileges that are associated with the user profile. If none of the servers authenticates the user, the user login fails.

NOTE: The NSMXpress appliance must be configured as a RADIUS client on

a RADIUS server so that the RADIUS server responds to authentication requests from NSMXpress. Select any Juniper Make or Model in the

Make/Model field while adding an NSMXpress appliance as a RADIUS client.

You will need to update the juniper dictionary file (juniper.dct) in the RADIUS server with the Juniper defined Vendor-Specific Attribute (VSA) for NSMXpress:ATTRIBUTE Juniper-Nsmxpress-Profile Juniper-VSA(6, string) r . You will also need to add NSMXpress users with their associated user profiles (SysAdmin, NSMAdmin, Operator, Guest), to the RADIUS database. For more details see Steel-Belted Radius Documentation.

NSMXpress Quick Start

NOTE: You need System Administration or NSM Administration permission

to manage RADIUS servers in the NSMXpress WebUI.

•

Adding a RADIUS Server on page 26

•

Changing the Priority of RADIUS Servers on page 27

•

Deleting a RADIUS Server on page 27

•

Editing RADIUS Server Parameters on page 27

Adding a RADIUS Server

To add a RADIUS server:

1. Select System Administration > Radius Management. The RADIUS Servers dialog box

appears listing the RADIUS Servers that have been added. See Figure 29 on page 26.

Figure 29: RADIUS Servers Dialog Box

2. Click Add to add a RADIUS Server to the WebUI. The Add Radius Server dialog box

appears. See Figure 30 on page 26.

Figure 30: Add RADIUS Server Dialog Box

3. Configure the following parameters in the Add RADIUS Server dialog box:

a. Name: The name of the user to be authenticated by the RADIUS server.

b. Server address: The IP address or the hostname of the RADIUS Server.

c. Shared secret: The shared secret NSMXpress and the RADIUS server use for secure

authentication.

Managing System Administration

d. Auth Port: The RADIUS authentication software port. (We recommend UDP port

1812.)

e. Acct Port: The RADIUS accounting software port. (We recommend UDP port 1813.)

f. Disconnect/CoA port: The change of authorization or disconnect port.

g. Timeout (sec): Automatic time out in second(s) of the RADIUS access-request

after which the request will be retransmitted, if applicable. Enter a value between 1 and 10 seconds.

h. Retries: The number of times the RADIUS access-request must be retransmitted

for RADIUS authentication. Enter a value between 1 and 5.

4. Click Add. The RADIUS Servers dialog box appears with the RADIUS Server you added

listed.

Changing the Priority of RADIUS Servers

To change the priority of RADIUS servers:

1. Select System Administration > Radius Management. The RADIUS Servers dialog box

appears listing the RADIUS Servers that have been added.

2. To increase the priority of a RADIUS server, select the check box next to the name of

the server whose priority you want to increase, and click Move Up.

To decrease the priority of a RADIUS server, select the check box next to the name of the server whose priority you want to decrease, and click Move Down.

Deleting a RADIUS Server

To delete a RADIUS server:

1. Select System Administration > Radius Management. The RADIUS Servers dialog box

appears listing the RADIUS Servers that have been added.

2. Select the check box next to the name of the server you want to delete, and click

Delete Selected.

NOTE: You need System Administration permissions to delete RADIUS servers.

Editing RADIUS Server Parameters

To edit the parameters of a RADIUS server:

1. Select System Administration > Radius Management. The RADIUS Servers dialog box

appears listing the RADIUS Servers that have been added.

2. Click the name of the server whose properties you want to edit. The Edit RADIUS

Server dialog box appears. See Figure 31 on page 28.

NSMXpress Quick Start

Monitoring with SNMP

Figure 31: Edit RADIUS Server Dialog Box

3. Edit the parameters you want to change and click Save.

You can configure your NSMXpress appliance for SNMP monitoring from a network operations server. The server can then issue periodic SNMP Get instructions to return the status of the NSMXpress appliance.

You configure SNMP on the NSMXpress appliances with access credentials for either SNMP v2c or SNMP v3. NSMXpress supports read-only access to the System Descriptor (sysDescr) and Host Resource MIB.

This section provides instructions for configuring NSMXpress for SNMP monitoring. You must provide access credentials for the SNMP server, a list of IP addresses from which logon requests will be accepted, and the trap conditions to be reported to the SNMP server.

To configure SNMP monitoring of your NSMXpress appliance, select System Administration > SNMP Monitoring. The SNMP window appears. This window contains the tabs described in the following sections:

•

SNMP Configuration on page 28

•

SNMP System Information on page 29

•

SNMP Trap Configuration on page 30

SNMP Configuration

To configure SNMP:

1. Select System Administration > SNMP Monitoring.

2. Select the SNMP Config tab, which is shown in Figure 32 on page 29.

Figure 32: Configuring SNMP

3. Select the version of SNMP to be used, either v2c or v3.

4. Provide authentication information:

•

If you selected SNMP v2c, enter a username.

•

If you selected SNMP v3, enter a username and password.

Managing System Administration

The password must be at least 8 characters long.

NSMXpress implements a single username and password, which is effective only for SNMP communication and is not related to any other username and password used on the NSMXpress appliance.

5. To limit SNMP Get requests to specific servers, select Only, and then enter the IP

addresses of the permitted servers.

6. Click Save.

SNMP System Information

To configure SNMP system information:

1. Select System Administration > SNMP Monitoring.

2. Select the System Info tab, which is shown in Figure 33 on page 29.

Figure 33: Configuring SNMP System Information

3. Enter the following information, which is required for any SNMP-managed device:

•

Contact—Contact information for the appliance.

•

Location—Location of the appliance.

NSMXpress Quick Start

•

Description—A brief description of the appliance.

4. Click Save.

SNMP Trap Configuration

To configure SNMP trap conditions:

1. Select System Administration > SNMP Monitoring.

2. Select the SNMP Traps tab, which is shown in Figure 34 on page 30.

Figure 34: Configuring SNMP Traps

3. In the Manager IP field, enter the IP address of the SNMP management server.

4. Select from the following trap conditions:

•

Disk space low

Enter the percentage of free disk space below which SNMP issues a trap.

•

Memory low

Enter the percentage of free memory below which SNMP issues a trap.

•

CPU high

Enter the percentage of CPU use over which SNMP issues a trap.

•

NSM start/stop

•

Admin Logon/Logoff

•

External IP unreachable

Enter the IP address of the required device.

5. Click Save.

Forwarding Syslog Messages

NSMXpress provides a simple mechanism for configuring syslog messaging between the NSMXpress appliance and a syslog receiver running rsyslog, syslog-NG, or basic syslog. This mechanism simplifies choosing syslog receivers, data sources of the messages you want to log, and the message transport used.

For the type of message transport, you can choose among TCP,SSL, and UDP. For rsyslog or syslog-NG implementations use TCP or SSL. SSL adds security to TCP; if you select SSL, NSMXpress createsa secure tunnel to the syslogreceiver. UDP messaging is available for basic syslog implementations.

The following sections provide procedures for managing syslog message forwarding:

•

Viewing Syslog Receivers on page 31

•

Adding and Configuring Syslog Receivers on page 32

•

Editing Syslog Receiver Configurations on page 34

•

Deleting Syslog Receivers on page 34

Managing System Administration

Viewing Syslog Receivers

To view the syslog receivers configured on your NSMXpress appliance, followthese steps:

1. Select System Administration > Syslog Forwarding. The Syslog Forwarding window

appears. Figure 35 on page 33 shows an example.

NSMXpress Quick Start

2. View the configured syslog receivers in the table in the top portion of the window.

Table 3 on page 32 describes the fields.

Table 3: Viewing Syslog Receivers

DescriptionField

Receiver

A name provided by the network administratorto identify the syslog receiver

The IP address of the syslog receiverIP Address

The protocol used for forwarding messages: UDP, TCP, SSLType

The data sources configured for forwardingData sources

The system logs configured to be sent to this receiver.System

The Device Server logs configured to be sent to this receiver.Device Server

The GUI Server logs configured to be sent to this receiver.GUI Server

The HA Server logs configured to be sent to this receiver.HA Server

Adding and Configuring Syslog Receivers

To add and configure a syslog receiver, follow these steps:

1. Select System Administration > Syslog Forwarding.

2. In the Data Sources section, select the syslog facility for each GUI Server log, Device

Server log, and HA Server log. The syslog facility is a field included in the syslog message to help identify the data source.

3. Click Save.

4. Click Add new Receiver.

The syslog receiver configuration window appears as shown in Figure 35 on page 33.

Figure 35: Configuring a Syslog Receiver

Managing System Administration

5. In the Name field, enter a name for the syslog receiver. This is the name that the syslog

receiver will be known by within NSM.

6. In the IP field, Enter the IP address of the syslog receiver.

7. In the Transport field, select the type of syslog receiver:

•

Select UDP for basic syslog implementations.

•

Select TCP for rsyslog or syslog-NG implementations.

NSMXpress Quick Start

•

Select SSL to create a secure tunnel to a syslog receiver in rsyslog or syslog-NG implementations.

•

In the System Logs section of the Data Sources table, select the sources of data from which system messageswill be forwardedto the syslog receiver. These sources can include NSMXpress system messages, package updates, and mail logs.

•

In the NSM section of the Data sources table, select each GUI Server log, Device Server log, and HA Server log to be forwarded to the syslog receiver.

8. Click Save to save and apply the configuration.

Editing Syslog Receiver Configurations

To edit a syslog receiver configuration, follow these steps:

1. Select System Administration > Syslog Forwarding.

2. In the Syslog Receivers window, click the name of the syslog receiver you want to edit.

The syslog receiver configuration window appears for the selected receiver.

3. Make the desired changes to the configuration.

4. Click Save to save and apply your edits to the configuration of this syslog receiver.

Deleting Syslog Receivers

To delete a syslog receiver configuration, follow these steps:

1. Select System Administration > Syslog Forwarding.

2. In the Syslog Receivers window, check the box next to each syslog receiver you want

to delete.

3. Click Delete selected receivers.

NSMXpress deletes the selected syslog receivers and any secure tunnels configured for their use.

Changing the System Time

To set the system time, select System Administration > System Time. From the System Time window, you can perform the following functions:

•

Set or change the system time.

•

Set the time zone.

•

Configure an NTP server to synchronize the system time with an external clock.

Installing Updates

Select System Administration > System Update to perform the following tasks:

•

Check for updates and install them.

•

Enable or disable automatic updates.

Managing Users

Managing System Administration

•

Install a new NSMXpress version.

•

Add or modify proxy settings for the Yum server.

The NSMXpress WebUIallows you to create multiple users with role-based access control to the WebUI. You can create a user in the WebUI and associate the user to a predefined user profile. You can also map a user created in the NSMXpress OS to a predefined user profile in the WebUI. However, this user profile is only applicable to the local OS user in the WebUI.

NOTE: You need System Administration permission to create users.

This topic contains the following sections:

•

Creating New NSMXpress Users on page 35

•

Deleting a User on page 37

•

Editing User Attributes on page 37

•

Understanding User Profiles on page 37

Creating New NSMXpress Users

To create a local OS user:

1. Select System Administration > User Management. The NSMXpress Users dialog box

appears listing all NSMXpress users. See Figure 36 on page 35.

Figure 36: NSMXpress Users Dialog Box

2. Click Create a new NSMXpress User. The Create NSMXpress user dialog box appears.

See Figure 37 on page 36.

NSMXpress Quick Start

Figure 37: Create NSMXpress User Dialog Box

3. Enter the user name in the local OS, in the Username text box.

4. Select Unix authentication from the Password drop-down list. The Password and

Confirm Password text boxes will be disabled since the password will be fetched from the local OS.

5. From the User Profile drop-down list box, select the user profile you want to associate

with the local user in the WebUI.

6. Click Submit. The NSMXpress Users dialog box appears with the new NSMXpress user

listed.

To create a WebUI user:

1. Select System Administration > User Management. The NSMXpress Users dialog box

appears listing all NSMXpress users. See Figure 38 on page 36.

Figure 38: NSMXpress Users Dialog Box

2. Click Create a new NSMXpress User. The Create NSMXpress user dialog box appears.

3. Enter a user name in the Username text box.

4. Select Set to from the password drop-down list and enter the password you want to

set in the password text box.

5. Reenter the password in the Confirm Password text box.

Managing System Administration

6. Select the user profile you want to associate with this user from the User Profile

drop-down list box.

7. Click Submit. The NSMXpress Users dialog box appears with the new NSMXpress user

listed.

Deleting a User

To delete a user:

1. Select System Administration > User Management. The NSMXpress Users dialog box

appears listing all NSMXpress users.

2. Select the check box next to the name of the user you want to delete and click Delete

Selected. Click Delete User in the Delete Users confirmation dialog box that appears.

NOTE: You cannot delete admin users or change their user profiles.

Editing User Attributes

To edit user attributes:

1. Select System Administration > User Management. The NSMXpress Users dialog box

appears, with all NSMXpress users listed.

2. Click on the name of the user whose attributes you want to edit. The Edit NSMXpress

Users dialog box appears.

3. Edit the parameters you want to change and click Submit. You can change the

password and the user profile.

Understanding User Profiles

NSMXpress provides four predefined user profiles that allow you to implement role-based accesscontrol over the NSMXpress WebUI.A user created via the WebUIor in the RADIUS server can be associated with any one of the following profiles:

•

System Administrator—System Administrators are superusers for the NSMXpress WebUI and have full access to all the modules in the NSMXpress WebUI.

•

NSM Administrator—NSM Administrators have access to NSM Administration, Radius Management, Maintenance and Troubleshooting modules.

•

Network Operator—Network Operators have access to Network Utilities and Report Generation Modules.

•

Guest User—Guest Users haveread access to System Information and System Statistics modules.

When a user logs in, NSMXpress modules are displayed or hidden based on the user profile and the permissions associated with the profile. For more details about user profiles and permissions, see Table 4 on page 38.

NSMXpress Quick Start

Table 4: NSMXpress WebUI User Profiles and Permissions

System Administration

System AdministratorNSMXpress Modules

NSM Administrator

Network Operator

Guest User

NoNoNoYesBootup and Shutdown

NoNoNoYesChange User Password

NoNoNoYesNetwork Configuration

NoNoYesYesRadius Management

NoNoNoYesSNMP Monitoring

NoNoNoYesSyslog Forwarding

NoNoNoYesSystem Time

NoNoNoYesSystem Update

NoNoNoYesUser Management

NoNoNoYesWebUI Configuration

NSM Administration

Maintenance

Troubleshooting

NoNoYesYesChange NSM Super User Password

NoNoYesYesDownload NSM MIBs

NoYesYesYesExport Audit Logs

NoYesYesYesExport Device Logs

NoYesYesYesGenerate Reports

NoNoYesYesNSM Configuration Files

NoNoYesYesNSM Database Backup

NoNoYesYesNSM Management IP

NoNoYesYesSchedule Security Updates

YesYesYesYesSystem Statistics

NoNoYesYesAction Audit Logs

Table 4: NSMXpress WebUI User Profiles and Permissions (continued)

Maintaining NSMXpress

Configuring the Web Interface

To specify which NSM client computerscan accessNSMXpress through the Webinterface, selectSystemAdministration> WebUI Configuration. The AllowedIP Addresseswindow appears as shown in Figure 39 on page 39.

Figure 39: Web Interface Access

System AdministratorNSMXpress Modules

NSM Administrator

Network Operator

Guest User

NoYesYesYesError Logs

NoYesYesYesNetwork Utilities

NoYesYesYesTech Support

YesYesYesYesSystem Information

Maintaining NSMXpress

The Maintaining section of the NSMXpress navigation tree allows you to perform the tasks described in the following sections:

•

Viewing System Statistics on page 39

•

Upgrading the Recovery Partition on page 41

Viewing System Statistics

To view system statistics, select System Administration > Maintenance > System Statistics. The system Statistics window appears as shown in Figure 40 on page 40.

NSMXpress Quick Start

Figure 40: System Statistics

CPU

Select CPU to view graphs that monitor the CPU activity hourly, daily, weekly, monthly, or on a customizable basis.

Log Rate

Select lograte to view graphs that monitor the log rate hourly, daily, weekly, monthly, or on a customizable basis.

CPU Load

Select Load to view graphs that monitor the CPU load hourly, daily, weekly, monthly, or on a customizable basis.

Memory Data

Select Memory to view graphs that monitor the memory activity hourly, daily, weekly, and monthly.

Network Data

Select either eth0 or eth1 to view graphs that monitor network activity hourly, daily, weekly, and monthly.

Process Count

SelectProcess to view graphs that monitor the number of processeshourly,daily,weekly, and monthly.

Disk Data

Select Disk to view graphs that monitor the file system disk space usage hourly, daily, weekly, and monthly.

Tile All Graphs

Select Tile all graphs to display all the statistical graphs for the system in one window.

Upgrading the Recovery Partition

The recovery partition contains all files necessary to perform a clean installation of the NSMXpress OS and its applications with default settings. It provides a last-resort recovery mechanism. When the NSMXpress appliance is shipped from the factory, the recovery partition files match the version of the NSMXpress OS with factory default settings.

Using the Recovery Upgrade option, you can make the current version of NSMXpress available for recovery, displacing the existing files in the recovery partition. The factory default recovery files are retained as an alternative recovery choice. Other versions are deleted.

Recovery upgrade uses two sets of packages to create a set of files from which you can perform a clean installation. One set makes up the NSMXpress OS, the other a set of upgrade script packages. Both sets are usually retained in the local file system. The NSMXpress OS set can also be downloaded form the Juniper Networks software repository.

NSMXpress splits the recovery upgrade process into a preparation phase and an upgrade phase. In the preparation phase, NSMXpress assembles a copy of the current version of the image files in temporary workspace. In the upgrade phase, NSMXpress replaces the old recovery image files, and installs the current version of the image files from the temporaryworkspaceinto the recovery partition. By splitting the process into two phases, NSMXpress minimizes the period of vulnerability while the upgrade itself takes place.

Maintaining NSMXpress

To upgrade the recovery partition, follow these steps:

1. Select System Administration > Maintenance > Update Recovery Partition.

If the new recovery partition files have already been prepared,then the Upgrade screen appears. Proceed with the upgrade phase as described in step 5.

If the upgrade files have not yet been prepared, the Upgrade Preparation window appears. Proceed with the preparation phase in step 2.

2. Enter the location of the NSMXpress Regional server or Central Manager upgrade zip

file, downloaded from the Juniper Customer Support Center when upgrading NSM, on the local file system.

3. If the NSMXpress Offline server upgrade file is available on the local file system, enter

the location and name of the NSMXpress offline server upgrade file in the System upgrade source field. If the NSMXpress offline server upgrade file is not available on the local file system and the appliance has access to the Juniper Update site, select Online.

4. Click Prepare System.

The Preparation Progress screen shows the progress of the operation.

Errors are reported if the required files are unavailable, disk space is not sufficient, or the previous version files are invalid.

When preparation is completed, the Upgrade window appears.

5. In the Upgrade window, enter the admin WebUI passwordand then click Start Update.

NSMXpress Quick Start

Troubleshooting

Use the options in the Troubleshooting section to access the following information and utilities:

•

Auditing User Operations on page 42

•

Error Logs on page 43

•

Network Utilities on page 44

•

Tech Support on page 47

Auditing User Operations

The upgrade process usually takes less than one minute.

CAUTION: Do not interrupt the upgrade process. If you do, your NSMXpress

appliance might not boot normally.

You can audit all user operations performed in NSMXpress. Users with System Administrator and NSM administrator permissions can view all Actions Logs in NSMXpress.

To view Action Audit Logs:

1. Select Troubleshooting > Action Audit Logs. The NSMXpress Actions Log dialog box

appears. See Figure 41 on page 42.

Figure 41: NSMXpress Actions Dialog Box

2. Select the Action Audit Logs that you want to view:

Troubleshooting

•

Actions by NSMXpress Users: Select the By any user check box to select actions by

all users. Select the By user check box and choose a username from the drop-down list to specify actions by a particular user. Select By any user except and choose a username from the drop-down list to exclude actions by a specific user.

•

Actions by User Profile: Select the By any profile check box to select actions by all

user profiles. Selectthe By profile check box and choose a profile from the drop-down list to specify actions by a specific user profile. Select By any profile except and choose a profile from the drop-down list to exclude actions by a user profile.

•

Actions by authentication mechanism: Select the By any authentication check box

to select actions by all authentication mechanisms. Select the By authentication check box and choose an authentication mechanism from the drop-down list to specify actions by a specific authentication mechanism. Select By any authentication

except and choose a profile from the drop-down list to exclude actions by an

authentication mechanism.

•

Actionsin module: Select the In any module check box to select actions in all modules.

Select the In module check box and choose a module from the drop-down list to specify actions in a particular module.

•

Actions on dates: Select the At any time check box to select actions at any time.

Selectthe For today only check box to select today’s actions. Select the For yesterday

only check box to select yesterday’s actions. Select the During the last week check

box to select last week’s actions. Select the Between check box and enter the start date and end date in the drop-down list to view actions within the specified time period.

3. Click Search. The Search Results dialog box appears with the result of your query. See

Figure 42 on page 43.

Figure 42: Search Results Dialog Box

Error Logs

To review error logs, select Troubleshooting > Error Logs. Figure 43 on page 44 shows an example,

NSMXpress Quick Start

Figure 43: Review Error Logs

To view details of an individual error log, select the file you want to view and click View. Figure 44 on page 44 shows sample error log details.

Figure 44: Error Log Detail

Network Utilities

To access basic network utilities (ping, traceroute, and nslookup) for TCP/IP Networking, select Troubleshooting > Network Utilities. These tools also provide an IP subnet calculator. SeeFigure 45 on page 44.

Figure 45: Network Utilities Options

Ping

Ping is a tool for checking network connectivity. NSMXpress prompts with questions so you can focus your search.

Figure 46 on page 45 shows an example.

Troubleshooting

Figure 46: Ping Utility

How Many Packets

Enter the number of packets this ping command will send. The default is 5. The values range from 1 through 99.

Packet Size

Enter the packet size (in bytes) this ping command will send. The default is 56. The values range from 1 through 9999.

How Many Sec Between Sending Each Packet

Enter how much time (in seconds) ping should wait between sending each packet.

Patterns to Send (Hex)

The data sent by ping contains a hexadecimal pattern. If you leave this option blank, ping will fill it with random data. This option is useful if you do not have problems with connectivity itself but with data loss.

Verbosity Output

NSMXpress lists the ICMP packets (other than ECHO_Response) that have been received.

Numeric Output Only

Check this option if you do not want any attemptsto be made to look up symbolic names for host addresses.

Bypass Routing Tables

If the host is not a directly attached network, an error is returned. This option can be used to ping a local host through an interface that has no route through it.

Traceroute

Traceroute is a tool to print the route a packet takes to a network host. See Figure 47 on page 46.

NSMXpress Quick Start

Figure 47: Traceroute Utility

NOTE: The only required field is Hostname. The value can be either a hostname or an IP address.

Lookup

Use the lookup tool to obtain the IP address from a hostname and the hostname from an IP address (see Figure 48 on page 46). The query type drop-down list contains several types of records found in the DNS database. Enter a nameserver or select the default. If you choose the default, nslookup will use the server on which NSMXpress is installed.

Figure 48: Lookup Utility

IP Subnet Calculator

Use the IP subnet calculator to calculate the netmask for a TCP/IP-network. You can calculate a netmask by class and subnet bits or by the number of hosts (See Figure 49 on page 47) When you calculate a netmask by the number of hosts, NSMXpress returns the smallest network available.

Tech Support

Viewing System Information

Figure 49: IP Subnet Calculator

To get contact information for Juniper Networks technical support, select Troubleshooting > Tech Support. To help analyze problems, select a detail type in the drop-down list box,

and then click Run Tech-Support Script. NSMXpress creates a file you can download and send to Juniper Networks technical support. See Figure 50 on page 47.

Figure 50: Juniper Tech Support

Viewing System Information

Use the SystemInformation menu item to display information about the server, including CPU load and memory use, as shown in Figure 51 on page 48.

NSMXpress Quick Start

Figure 51: System Information

List of Technical Publications

Table 5 on page 48 describes the documentation for NSMXpress and NSM.

Table 5: Network and Security Manager Publications

DescriptionBook

Network and Security Manager Installation Guide

Network and Security Manager Administration Guide

Network and Security Manager Configuring ScreenOS and IDP Devices Guide

Describes the steps to install the NSM management system on a single server or on separate servers. It also includes information on how to install and run the NSM user interface. This guide is intended for IT administrators responsible for the installation or upgrade of NSM.

Describes how to use and configure key management features in the NSM. It provides conceptual information, suggested workflows, and examples. This guide is best used in conjunction with the NSM Online Help, which provides step-by-step instructions for performing management tasks in the NSM user interface (UI).

This guide is intended for application administrators or those individuals responsible for owning the server and security infrastructure and configuring the product for multiuser systems. It is also intended for device configuration administrators, firewall and VPN administrators, and network security operation center administrators.

Describes NSM features related to device configuration and management. It also explains how to configure basic and advanced NSM functionality, including deploying new device configurations, managing security policies and VPNs, and general device administration.

Network and Security Manager Online Help

Provides procedures for basic tasks in the NSM user interface. It also includes a brief overview of the NSM system and a description of the GUI elements.

Requesting Technical Support

Table 5: Network and Security Manager Publications (continued)

DescriptionBook

Network and Security Manager API Guide

Network and Security Manager Release Notes

NSMXpress and NSM3000 User Guide

Requesting Technical Support

Technical product support is available through the Juniper Networks Technical Assistance Center (JTAC). If you are a customer with an active J-Care or JNASC support contract, or are covered under warranty, and need post-sales technical support, you can access our tools and resources online or open a case with JTAC.

•

JTAC policies—For a complete understanding of our JTAC procedures and policies, review the JTAC User Guide located at

http://www.juniper.net/us/en/local/pdf/resource-guides/7100059-en.pdf .

•

Product warranties—For product warranty information, visit

http://www.juniper.net/support/warranty/ .

Provides complete syntax and a description of the Simple Object Access Protocol (SOAP) messaging interface to NSM.

Provides the latest information about features, changes, known problems, resolved problems, and system maximum values. If the information in the Release Notes differs from the information found in the documentation set, follow the Release Notes.

Release Notes are included on the corresponding software CD and are available on the Juniper Networks Website.

Describes how to set up and manage the NSM appliances as a central manager or regional server.

•

JTAC hours of operation—The JTAC centers have resources available 24 hours a day, 7 days a week, 365 days a year.

Self-Help Online Tools and Resources

For quick and easy problem resolution, Juniper Networks has designed an online self-service portal called the Customer Support Center (CSC) that provides you with the following features:

•

Find CSC offerings: http://www.juniper.net/customers/support/

•

Search for known bugs: http://www2.juniper.net/kb/

•

Find product documentation: http://www.juniper.net/techpubs/

•

Find solutions and answer questions using our Knowledge Base: http://kb.juniper.net/

•

Download the latest versions of software and review release notes:

http://www.juniper.net/customers/csc/software/

•

Search technical bulletins for relevant hardware and software notifications:

https://www.juniper.net/alerts/

NSMXpress Quick Start

•

Join and participate in the Juniper Networks Community Forum:

http://www.juniper.net/company/communities/

•

Open a case online in the CSC Case Management tool: http://www.juniper.net/cm/

To verify service entitlement by product serial number,use our Serial Number Entitlement (SNE) Tool: https://tools.juniper.net/SerialNumberEntitlementSearch/

Opening a Case with JTAC

You can open a case with JTAC on the Web or by telephone.

•

Use the Case Management tool in the CSC at http://www.juniper.net/cm/ .

•

Call 1-888-314-JTAC (1-888-314-5822 toll-free in the USA, Canada, and Mexico).

For international or direct-dial options in countries without toll-free numbers, see

http://www.juniper.net/support/requesting-support.html .

Revision History

Requesting Technical Support

November 17, 2010— Revision 1.

Juniper Networks, Junos, Steel-Belted Radius, NetScreen, and ScreenOS are registered trademarks of Juniper Networks, Inc. in the United States and other countries. The Juniper Networks Logo, the Junos logo, and JunosE are trademarks of Juniper Networks, Inc. All other trademarks, service marks, registered trademarks, or registered service marks are the property of their respective owners.

Juniper Networks assumes no responsibility for any inaccuracies in this document. Juniper Networks reserves the right to change, modify, transfer, or otherwise revise this publication without notice.

Products made or sold by Juniper Networks or components thereof might be covered by one or more of the following patents that are owned by or licensed to Juniper Networks: U.S. Patent Nos. 5,473,599, 5,905,725, 5,909,440, 6,192,051, 6,333,650, 6,359,479, 6,406,312, 6,429,706, 6,459,579, 6,493,347, 6,538,518, 6,538,899, 6,552,918, 6,567,902, 6,578,186, and 6,590,785.

Juniper NETWORK AND SECURITY MANAGER NSMXPRESS - QUICK START REV1, NETWORK AND SECURITY MANAGER NSMXPRESS Quick Start Manual

Specifications and Main Features

Frequently Asked Questions

User Manual