Juniper ERX - RELEASE 11.1.X MODULE GUIDE 4-6-2010, ERX User Manual

E Series™ Broadband Services Routers

ERX™ Module Guide

Release 11.1.x

Juniper Networks, Inc.

1194 North Mathilda Avenue

Sunnyvale, California 94089

USA

408-745-2000

www.juniper.net

Published: 2010-04-06

ERX 11.1.x Module Guide

This guide provides an overview and description of the line modules (LMs), switch route processor (SRP) modules, and I/O modules available for the following Juniper Networks E Series Broadband Services Routers: ERX14xx models, ERX7xx models, and the ERX310 router.

Unless otherwise specified, all line modules pair with I/O modules to create a module combination. Each module combination provides particular capabilities and connections in an ERX router.

NOTE: A release may support multiple versions of a module. For information, see

Software Compatibility in JUNOSe System Basics Configuration Guide, Chapter 6, Managing Modules.

Table 1 on page 3 lists the module combinations supported by ERX routers.

This book also contains three appendixes:

■ Module Protocol Support on page 107

■ Module LEDs on page 133

■ Module Name Cross-Reference Information on page 139

■ Product Reclamation and Recycling Program on page 143

For more information about ERX routers and modules, refer to the following books:

■ Modules that have reached end-of-life—ERX End-of-Life Module Guide

■ Module installation and maintenance—ERX Hardware Guide

■ Managing ERX routers—JUNOSe System Basics Configuration Guide

■ Configuring ERX modules—JUNOSe Link Layer Configuration Guide

2 ■

Table 1: ERX Module Combinations

Channelized OC3/STM1

cOC3/STM1 multimode

Line Module LabelCombination Name and Type

cOCx/STMx F0

I/O Module Label

I/O

MULTIMODE

First JUNOSe Support

Page

92.2.0cOC3 STM1 F0

cOC3/STM1 single-mode intermediate reach

cOC3/STM1 single-mode long reach

Channelized OC12/STM4

cOC12/STM4 multimode without APS/MSP redundancy

cOC12/STM4 single-mode intermediate reach without APS/MSP redundancy

cOC12/STM4 single-mode intermediate reach with APS/MSP redundancy

cOC12/STM4 single-mode long reach

cOCx/STMx F0

I/O

SINGLE MODE

I/O

LONG HAUL

F0 I/O

MULTI MODE

F0 I/O

SINGLE MODE

COC12 F0 APS

SINGLE MODE

LONG HAUL

112.2.0cOC3 STM1 F0

132.2.0cOC3 STM1 F0

152.2.0cOC12 STM4

172.2.0cOC12 STM4

196.1.3,

7.0.2,

7.2.0

212.2.0cOC12 STM4

Channelized T3

E3

Fast Ethernet

Gigabit Ethernet (1-port)

233.2.0CT3/T3 12 I/OCT3/T3-F0CT3/T3 12 (12 ports)

COCX-F3E3 Frame (12 ports)

244.0.2E3-12

FRAME I/O

255.0.0FE-8 I/OGE/FEFE-8 (8 ports) (256-MB memory)

266.0.0FE-8 SFP I/OGE/FEFE-8 SFP (8 ports) (256-MB memory)

285.0.0GE I/O SFPGE/FEGE 1000Base-SX (256-MB memory)

■ 3

ERX 11.1.x Module Guide

Table 1: ERX Module Combinations (continued)

Line Module LabelCombination Name and Type

I/O Module Label

First JUNOSe Support

Page

305.0.0GE I/O SFPGE/FEGE 1000Base-LH (256-MB memory)

325.0.0GE I/O SFPGE/FEGE 1000Base-ZX (256-MB memory)

Gigabit Ethernet (2-port)

GE/FEGE multimode

342.0.0GE I/O

MULTI MODE

GE/FEGE single-mode

362.0.0GE I/O

SINGLE MODE

GE-2GE2 1000Base-SX

385.3.0GE-2 SFP I/O

or

2XGE APS I/O SFP or

GE-2 APS I/O SFP

GE-2GE2 1000Base-LH

405.3.0GE-2 SFP I/O

or

2XGE APS I/O SFP or

GE-2 APS I/O SFP

GE-2GE2 1000Base-ZX

425.3.0GE-2 SFP I/O

or

GE High Density (HDE)

4 ■

2XGE APS I/O SFP or

GE-2 APS I/O SFP

GE-HDEGE High Density (2 ports)

447.0.0GE-2 SFP I/O

or

2XGE APS I/O SFP or

GE-2 APS I/O SFP

467.0.0GE-8 I/OGE-HDEGE High Density (8 ports)

Table 1: ERX Module Combinations (continued)

Line Module LabelCombination Name and Type

IPSec Service

SERVICE

OC3/STM1 ATM

OC3/STM1 ATM multimode without APS/MSP redundancy (256-MB memory)

OCx/STMx ATM or OCx/STMx /DS3-ATM

I/O Module Label

OC3-4 I/O

MULTI MODE

First JUNOSe Support

5.3.0

Page

484.0.2No I/O moduleIPSEC

495.0.0,

OC3/STM1 ATM multimode with APS/MSP redundancy

OC3/STM1 ATM single-mode intermediate reach without APS/MSP redundancy (256-MB memory)

OC3/STM1 ATM single-mode intermediate reach with APS/MSP redundancy

OC3/STM1 ATM single-mode long reach without APS/MSP redundancy (256-MB memory)

OC3/STM1 GE/FE

OC3/STM1 POS

OC3/STM1 POS multimode without APS/MSP redundancy

OCx/STMx ATM or OCx/STMx /DS3-ATM

OC3/STM1 GE/FE

OCx/STMx POS

4XOC3 APS I/O

MULTI MODE

OC3-4 I/O

SINGLE MODE

4XOC3

APS I/O

SINGLE MODE

OC3-4 I/O

LONG HAUL

APS I/O

MULTI MODE

515.1.2

5.2.0 (APS/MSP)

535.0.0,

5.3.0

555.1.2

5.2.0 (APS/MSP)

575.0.0,

5.3.0

596.1.0OC3–2 GE

632.0.0OC3-4 I/O

OC3/STM1 POS multimode with APS/MSP redundancy

OC3/STM1 POS single-mode intermediate reach without APS/MSP redundancy

OCx/STMx POS

4XOC3 APS I/O

MULTI MODE

SINGLE MODE

655.1.2

5.2.0 (APS/MSP)

672.0.0OC3-4 I/O

■ 5

ERX 11.1.x Module Guide

Table 1: ERX Module Combinations (continued)

Line Module LabelCombination Name and Type

I/O Module Label

First JUNOSe Support

Page

OC3/STM1 POS single-mode intermediate reach with APS/MSP redundancy

OC3/STM1 POS single-mode long reach

OC12/STM4 ATM

OC12/STM4 ATM multimode without APS/MSP redundancy (256-MB memory)

OC12/STM4 ATM multimode with APS/MSP redundancy

OC12/STM4 ATM single-mode intermediate reach without APS/MSP redundancy (256-MB memory)

OC12/STM4 ATM single-mode intermediate reach with APS/MSP redundancy

OCx/STMx POS

OCx/STMx ATM or OCx/STMx /DS3-ATM

4XOC3 APS I/O

SINGLE MODE

LONG HAUL

OC12 STM4 I/O

MULTI MODE

OC12 STM4 APS

MULTI MODE

OC12 STM4 I/O

SINGLE MODE

OC12 STM4 APS

SINGLE MODE

695.1.2

5.2.0 (APS/MSP)

712.0.0OC3-4 I/O

735.0.0,

5.3.0

752.0.0 (128

MB)

5.0.0 (256 MB)

775.0.0,

5.3.0

792.0.0 (128

MB)

5.0.0 (256 MB)

OC12/STM4 ATM single-mode long reach without APS/MSP redundancy (256-MB memory)

OC12/STM4 ATM single-mode long reach with APS/MSP redundancy

OC12/STM4 POS

OC12/STM4 POS multimode without APS/MSP redundancy

6 ■

OCx/STMx ATM or OCx/STMx /DS3-ATM

OCx/STMx POS

OC12 STM4 I/O

LONG HAUL

OC12 STM4 APS

LONG HAUL

I/O

MULTI MODE

5.3.0

815.0.0,

832.0.0 (128

MB)

5.0.0 (256 MB)

852.0.0OC12 STM4

Table 1: ERX Module Combinations (continued)

Line Module LabelCombination Name and Type

I/O Module Label

First JUNOSe Support

Page

OC12/STM4 POS multimode with APS/MSP redundancy

OC12/STM4 POS single-mode intermediate reach without APS/MSP redundancy

OC12/STM4 POS single-mode intermediate reach with APS/MSP redundancy

OC12/STM4 POS single-mode long reach without APS/MSP redundancy

OC12/STM4 POS single-mode long reach with APS/MSP redundancy

OC48/STM16

OCx/STMx POS

OC48OC48/STM16 POS single-mode short reach

APS

872.0.0OC12 STM4

MULTI MODE

892.0.0OC12 STM4

I/O

SINGLE MODE

912.0.0OC12 STM4

APS

SINGLE MODE

932.0.0OC12 STM4

I/O

LONG HAUL

952.0.0OC12 STM4

APS

LONG HAUL

974.1.xOC48 FRAME

APS

Service Module (SM)

SM

SRPs

SRP-40G PLUS (2-GB memory)

MODULE

PLUS

985.1.0No I/O moduleSERVICE

SRP I/OSRP-5G+SRP-5G+ (1-GB memory)

994.1.3,

5.0.4,

5.1.2,

5.2.0

SRP I/OSRP-5G+SRP-5G+ (2-GB memory)

1004.1.3,

5.0.4,

5.1.2,

5.2.0

SRP I/OSRP-10GSRP-10G (2-GB memory)

1014.1.3,

5.0.4,

5.1.2,

5.2.0

1024.0.0SRP I/OSRP-40G

■ 7

ERX 11.1.x Module Guide

Table 1: ERX Module Combinations (continued)

Line Module LabelCombination Name and Type

T3

T3 ATM (4 ports)

OCx/STMx ATM or OCx/STMx /DS3-ATM

I/O Module Label

4xDS3 ATM I/O

First JUNOSe Support

MB)

5.0.0 (256 MB)

Page

1035.3.0SRP-SE I/OSRP-SE10GSRP-SE10G (1-GB memory)

1044.1.0 (128

1054.0.2CT3/T3 12 I/OCOCX-F3T3 Frame (12 ports)

8 ■

cOC3/STM1 Multimode Module Combination

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

cOCx/STMx F0

cOC3 STM1 F0 I/O

MULTI MODE

4

■

First supported: 2.2.0

■

Final supported: Not applicable

■

130 W

■

OC3/STM1 channelized to DS3, DS1, E1, and DS0

■

Supports either E1 or T1 operation, but not E1 and T1 operation simultaneously

■

EFA ASIC

■

OC3/STM1

■

DS3

■

T1, E1

■

DS0

■

HDLC framing

■

See “Channelized OCx/STMx Modules” on page 107 for information about the layer

■

2 and layer 3 protocols and applications that this module combination supports.

Model compatibility

SRP module compatibility

Module redundancy support

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

1:N redundancy

■

NOTE: Line module redundancy is not supported on the ERX310 router.

■

cOC3/STM1 Multimode Module Combination ■ 9

ERX 11.1.x Module Guide

Cables and connectors

LEDs

Alarms, errors, and events

Up to four SC full duplex connectors

■

Tx power:

■

min: –19 dBm

■

max: –14 dBm

■

Center wavelength: 1310 nm

■

Rx input power:

■

min: –30 dBm

■

max: –14 dBm

■

Rated for 2 km (1.2 miles) over 62.5-micron core cable with an optical loss of

■

0–9 dB or 50-micron core cable with an optical loss of 7 dB

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring Interfaces in JUNOSe Physical Layer Configuration Guide, Chapter 4,

■

Configuring Channelized OCx/STMx Interfaces.

10 ■ cOC3/STM1 Multimode Module Combination

cOC3/STM1 Single-Mode Intermediate Reach Module Combination

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

cOCx/STMx F0

cOC3 STM1 F0 I/O

SINGLE MODE

4

■

First supported: 2.2.0

■

Final supported: Not applicable

■

130 W

■

OC3/STM1 channelized to DS3, DS1, E1, and DS0

■

EFA ASIC

■

OC3/STM1

■

DS3, DS1

■

T1, E1

■

DS0

■

HDLC framing

■

See “Channelized OCx/STMx Modules” on page 107 for information about the

■

layer 2 and layer 3 protocols and applications that this module combination supports.

Model compatibility

SRP module compatibility

Module redundancy support

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

1:N redundancy

■

NOTE: Line module redundancy is not supported on the ERX310 router.

■

cOC3/STM1 Single-Mode Intermediate Reach Module Combination ■ 11

ERX 11.1.x Module Guide

Cables and connectors

LEDs

Alarms, errors, and events

Up to four SC full duplex connectors

■

Tx power:

■

min: –15 dBm

■

max: –8 dBm

■

Center wavelength: 1310 nm

■

Rx input power:

■

min: –31 dBm

■

max: –8 dBm

■

Rated for 15 km (9.3 miles) of 9-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring Interfaces in JUNOSe Physical Layer Configuration Guide, Chapter 4,

■

Configuring Channelized OCx/STMx Interfaces.

12 ■ cOC3/STM1 Single-Mode Intermediate Reach Module Combination

cOC3/STM1 Single-Mode Long Reach Module Combination

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

cOCx/STMx F0

cOC3 STM1 F0 I/O

LONG HAUL

4

■

First supported: 2.2.0

■

Final supported: Not applicable

■

130 W

■

OC3/STM1 channelized to DS3, DS1, E1, and DS0

■

EFA ASIC

■

OC3/STM1

■

DS3, DS1

■

T1, E1

■

DS0

■

HDLC framing

■

See “Channelized OCx/STMx Modules” on page 107 for information about the

■

layer 2 and layer 3 protocols and applications that this module combination supports.

Model compatibility

SRP module compatibility

Module redundancy support

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

1:N redundancy

■

NOTE: Line module redundancy is not supported on the ERX310 router.

■

cOC3/STM1 Single-Mode Long Reach Module Combination ■ 13

ERX 11.1.x Module Guide

Cables and connectors

LEDs

Alarms, errors, and events

Up to four SC full duplex connectors

■

Tx power:

■

min: –5.0 dBm

■

max: 0 dBm

■

Center wavelength: 1310 nm

■

Rx input power:

■

min: –34 dBm

■

max: –7 dBm

■

Fiber type: 9-micron core

■

Rated for 40 km (24.8 miles) of 9-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring Interfaces in JUNOSe Physical Layer Configuration Guide, Chapter 4,

■

Configuring Channelized OCx/STMx Interfaces.

14 ■ cOC3/STM1 Single-Mode Long Reach Module Combination

cOC12/STM4 Multimode Without APS/MSP Redundancy Module Combination

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

cOCx/STMx F0

cOC12 STM4 F0 I/O

MULTI MODE

1

■

First supported: 2.2.0

■

Final supported: Not applicable

■

130 W

■

OC12/STM4 channelized to DS3, DS1, E1, and DS0

■

EFA ASIC

■

OC12/STM4

■

OC3/STM1

■

DS3, DS1

■

T1, E1

■

DS0

■

HDLC framing

■

See “Channelized OCx/STMx Modules” on page 107 for information about the layer

■

2 and layer 3 protocols and applications that this module combination supports.

Model compatibility

SRP module compatibility

Module redundancy support

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

1:N redundancy

■

NOTE: Line module redundancy is not supported on the ERX310 router.

■

cOC12/STM4 Multimode Without APS/MSP Redundancy Module Combination ■ 15

ERX 11.1.x Module Guide

Cables and connectors

LEDs

Alarms, errors, and events

SC full duplex connector

■

Tx power:

■

min: –19 dBm

■

max: –14 dBm

■

Center wavelength: 1310 nm

■

Rx input power:

■

min: –30 dBm

■

max: –14 dBm

■

Rated for 2 km (1.2 miles) over 62.5-micron core cable with an optical loss of 0–9

■

dB or 50-micron core cable with an optical loss of 7 dB

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring Interfaces in JUNOSe Physical Layer Configuration Guide, Chapter 4,

■

Configuring Channelized OCx/STMx Interfaces.

16 ■ cOC12/STM4 Multimode Without APS/MSP Redundancy Module Combination

cOC12/STM4 Single-Mode Intermediate Reach Without APS/MSP Redundancy Module Combination

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

cOCx/STMx F0

cOC12 STM4 F0 I/O

SINGLE MODE

1

■

First supported: 2.2.0

■

Final supported: Not applicable

■

130 W

■

OC12/STM4 channelized to DS3, DS1, E1, and DS0

■

EFA ASIC

■

OC12/STM4

■

OC3/STM1

■

DS3, DS1

■

T1, E1

■

DS0

■

HDLC framing

■

See “Channelized OCx/STMx Modules” on page 107 for information about the

■

layer 2 and layer 3 protocols and applications that this module combination supports.

Model compatibility

SRP module compatibility

Module redundancy support

cOC12/STM4 Single-Mode Intermediate Reach Without APS/MSP Redundancy Module Combination ■ 17

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

1:N redundancy

■

NOTE: Line module redundancy is not supported on the ERX310 router.

■

ERX 11.1.x Module Guide

Cables and connectors

LEDs

Alarms, errors, and events

SC full duplex connector

■

Tx power:

■

min: –15 dBm

■

max: –8 dBm

■

Center wavelength: 1310 nm

■

Rx input power:

■

min: –31 dBm

■

max: –8 dBm

■

Rated for 15 km (9.3 miles) of 9-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring Interfaces in JUNOSe Physical Layer Configuration Guide, Chapter 4,

■

Configuring Channelized OCx/STMx Interfaces.

18 ■ cOC12/STM4 Single-Mode Intermediate Reach Without APS/MSP Redundancy Module Combination

cOC12/STM4 Single-Mode Intermediate Reach With APS/MSP Redundancy Module Combination

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

cOCx/STMx F0

COC12 F0 APS

SINGLE MODE

2

■

1 active, 1 redundant

■

First supported: 6.1.3 or later 6.1.x release, 7.0.2 or later 7.0.x release, 7.2.0 and

■

higher-numbered release

130 W

■

OC12/STM4 channelized to DS3, DS1, E1, and DS0

■

EFA ASIC

■

OC12/STM4

■

OC3/STM1

■

DS3, DS1

■

T1, E1

■

DS0

■

HDLC framing

■

See “Channelized OCx/STMx Modules” on page 107 for information about the layer

■

2 and layer 3 protocols and applications that this module combination supports.

Model compatibility

SRP module compatibility

Module redundancy support

cOC12/STM4 Single-Mode Intermediate Reach With APS/MSP Redundancy Module Combination ■ 19

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

1:N redundancy

■

NOTE: Line module redundancy is not supported on the ERX310 router.

■

ERX 11.1.x Module Guide

Cables and connectors

LEDs

Alarms, errors, and events

SC full duplex connector

■

Tx power:

■

min: –15 dBm

■

max: –8 dBm

■

Center wavelength: 1310 nm

■

Rx input power:

■

min: –31 dBm

■

max: –7 dBm

■

Rated for 15 km (9.3 miles) of 9-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring Interfaces in JUNOSe Physical Layer Configuration Guide, Chapter 4,

■

Configuring Channelized OCx/STMx Interfaces.

20 ■ cOC12/STM4 Single-Mode Intermediate Reach With APS/MSP Redundancy Module Combination

cOC12/STM4 Single-Mode Long Reach Module Combination

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

cOCx/STMx F0

cOC12 STM4

LONG HAUL

1 active, 1 redundant

■

First supported: 2.2.0

■

Final supported: Not applicable

■

130 W

■

OC12/STM4 channelized to DS3, DS1, E1, and DS0

■

EFA ASIC

■

OC12/STM4

■

OC3/STM1

■

DS3, DS1

■

T1, E1

■

DS0

■

HDLC framing

■

See “Channelized OCx/STMx Modules” on page 107 for information about the

■

layer 2 and layer 3 protocols and applications that this module combination supports.

Model compatibility

SRP module compatibility

Module redundancy support

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

1:N redundancy

■

NOTE: Line module redundancy is not supported on the ERX310 router.

■

cOC12/STM4 Single-Mode Long Reach Module Combination ■ 21

ERX 11.1.x Module Guide

Cables and connectors

LEDs

Alarms, errors, and events

SC full duplex connector

■

Tx power:

■

min: –5.0 dBm

■

max: 0 dBm

■

Center wavelength: 1310 nm

■

Rx input power:

■

min: –34 dBm

■

max: –7 dBm

■

Fiber type: 9-micron core

■

Rated for 40 km (24.8 miles) of 9-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring Interfaces in JUNOSe Physical Layer Configuration Guide, Chapter 4,

■

Configuring Channelized OCx/STMx Interfaces.

22 ■ cOC12/STM4 Single-Mode Long Reach Module Combination

CT3/T3 12 Module Combination (12 Ports)

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

Model compatibility

SRP module compatibility

CT3/T3-F0

CT3/T3 12 I/O

12

■

First supported: 3.2.0

■

Final supported: Not applicable

■

130 W

■

Channelized and unchannelized T3

■

EFA ASIC

■

DS3, DS1, DS0

■

HDLC framing

■

See “Channelized T3 Modules” on page 110 for information about the layer 2 and

■

layer 3 protocols and applications that this module combination supports.

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

Module redundancy support

Cables and connectors

LEDs

Alarms, errors, and events

1:N redundancy

■

NOTE: Line module redundancy is not supported on the ERX310 router.

■

BT43 SMB connector

■

Cable that adapts to 75-ohm BNC is available.

■

The line interface unit supports two line buildouts:

■

0–68.5 m (0–225 feet)

■

69–137 m (226–450 feet)

■

Signal strength is software controlled.

■

The transmitted signal complies with ANSI T1.102-1993 Digital Hierarchy -

■

Electrical Interfaces (1999) for cable lengths up to 201 m (660 feet).

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring Interfaces in JUNOSe Physical Layer Configuration Guide, Chapter 1,

■

Configuring Channelized T3 Interfaces.

CT3/T3 12 Module Combination (12 Ports) ■ 23

ERX 11.1.x Module Guide

E3 Frame Module Combination (12 Ports)

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

Model compatibility

COCX-F3

E3-12

FRAME I/O

12

■

First supported: 4.0.2

■

Final supported: Not applicable

■

135 W

■

Unchannelized E3 for Frame

■

EFA ASIC

■

E3

■

HDLC framing

■

See “Unchannelized E3 Modules” on page 128 for information about the layer 2

■

and layer 3 protocols and applications that this module combination supports.

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP module compatibility

Module redundancy support

Cables and connectors

LEDs

Alarms, errors, and events

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

1:N redundancy

■

NOTE: Line module redundancy is not supported on the ERX310 router.

■

BT43 SMB connector

■

Cable that adapts to 75-ohm BNC is available.

■

The transmitted signal complies with ITUT G.703, Physical/electrical

■

characteristics of hierarchical digital interfaces (November 2001) for cable lengths from 0–137 m (0–450 feet).

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring Interfaces in JUNOSe Physical Layer Configuration Guide, Chapter 2,

■

Configuring T3 and E3 Interfaces.

24 ■ E3 Frame Module Combination (12 Ports)

FE-8 Module Combination (8 Ports) (256-MB Memory)

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

Model compatibility

GE/FE

FE-8 I/O

8

■

First supported: 5.0.0

■

Final supported: Not applicable

■

The GE/FE line module must have a minimum of 256 MB of memory to be used

■

with JUNOSe Release 5.3.0 or a higher-numbered release.

130 W

■

Fast Ethernet

■

EFA ASIC

■

IEEE 802.3 standards compliance

■

10/100Base-T

■

See “Ethernet Modules” on page 112 for information about the layer 2 and layer

■

3 protocols and applications that this module combination supports.

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP module compatibility

Module redundancy support

Cables and connectors

LEDs

Alarms, errors, and events

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

Not applicable

■

RJ-45 connectors

■

For 10-Mbps operation, use CAT 3, 4, or 5 UTP cable.

■

For 100-Mbps operation, use only CAT 5 UTP cable.

■

The transmitted signal complies with IEEE 802.3/802.3u for cable lengths up to

■

100 m (328 feet).

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring Ethernet Interfaces in JUNOSe Physical Layer Configuration Guide,

■

Chapter 5, Configuring Ethernet Interfaces.

FE-8 Module Combination (8 Ports) (256-MB Memory) ■ 25

ERX 11.1.x Module Guide

FE-8 SFP Module Combination (8 Ports) (256-MB Memory)

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

Model compatibility

GE/FE

FE-8 SFP I/O

8

■

First supported: 6.0.0

■

Final supported: Not applicable

■

130 W

■

Fast Ethernet

■

The FE-8 SFP I/O module uses a range of small form-factor pluggable (SFP)

■

transceivers to support different modes and cable lengths.

EFA ASIC

■

IEEE 802.3 standards compliance

■

100Base-FX

■

See “Ethernet Modules” on page 112 for information about the layer 2 and layer

■

3 protocols and applications that this module combination supports.

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP module compatibility

Module redundancy support

Cables and connectors (single-mode fiber)

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

Not applicable

■

LC full duplex

■

Tx power:

■

min: –15 dBm

■

max: –8 dBm

■

Center wavelength: 1300 nm

■

Rx input power:

■

min: –28 dBm

■

max: –14 dBm

■

Rated for 10 km (6.2 miles) over 9-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

26 ■ FE-8 SFP Module Combination (8 Ports) (256-MB Memory)

Cables and connectors (multimode fiber)

LEDs

Alarms, errors, and events

FE-8 SFP Module Combination (8 Ports) (256-MB Memory)

LC full duplex

■

Tx power: –20 dBm minimum and –14 dBm maximum

■

Center wavelength: 850 nm

■

Rx input power: –31 dBm minimum and –14 dBm maximum

■

Rated for 2 km (1.2 miles) over 62.5/125-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring Ethernet Interfaces in JUNOSe Physical Layer Configuration Guide,

■

Chapter 5, Configuring Ethernet Interfaces.

FE-8 SFP Module Combination (8 Ports) (256-MB Memory) ■ 27

ERX 11.1.x Module Guide

GE 1000Base-SX Module Combination (1 Port) (256-MB Memory)

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

GE/FE

GE I/O SFP

1 active, 1 redundant

■

First supported: 5.0.0

■

Final supported: Not applicable

■

130 W

■

Gigabit Ethernet

■

256 MB of memory

■

The 128-MB version has reached end-of-life.

■

The I/O module uses a range of small form-factor pluggable (SFP) transceivers to

■

support different modes and cabling distances.

Uses either optical or copper SFPs.

■

The optical transceivers are 1000Base-SX compliant.

■

The copper transceivers are 1000Base-T compliant.

■

Single-strand SFPs can be used. These SFPs work in pairs and require a matching

■

SFP at the opposite end of the Ethernet connection. For example, an SFP rated at TX 1310, RX 1550 must be paired with an SFP rated TX 1550, RX 1310 with the same maximum operating range. See the following corresponding table (Single-strand SFPs Pairing) for more information.

EFA ASIC

■

Capability

Software features

Model compatibility

SRP module compatibility

Module redundancy support

Cables and connectors (copper SFP)

Ethernet (IEEE 802.3z)

■

1000Base-SX

■

See “Ethernet Modules” on page 112 for information about the layer 2 and layer 3

■

protocols and applications that this module combination supports.

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

Not applicable

■

Maximum range is 100 meters on CAT5 cable.

■

28 ■ GE 1000Base-SX Module Combination (1 Port) (256-MB Memory)

Cables and connectors (SX)

LEDs

Alarms, errors, and events

GE 1000Base-SX Module Combination (1 Port) (256-MB Memory)

LC full duplex

■

Tx power:

■

min: –9.5 dBm

■

max: –4 dBm

■

Center wavelength: 850 nm

■

Rx input power:

■

min: –20 dBm

■

max: –0 dBm

■

Rated for 275 m (300 yards) over 62.5-micron core cable

■

Rated for 550 m (601 yards) over 50-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring Ethernet Interfaces in JUNOSe Physical Layer Configuration Guide,

■

Chapter 5, Configuring Ethernet Interfaces.

Table 2: Single-strand SFPs Pairing

9 microns

TX 1310, RX 1550

■

Pairs with TX 1550 / RX 1310

■

TX 1550 / RX 1310

■

Pairs with TX 1310, RX 1550

■

TX 1310, RX 1490

■

Pairs with TX 1490 / RX 1310

■

TX 1490 / RX 1310

■

Pairs with TX 1310, RX 1490

■

TX 1310, RX 1550

■

Pairs with TX 1550 / RX 1310

■

TX 1550, RX 1310

■

Pairs with TX 1310 / RX 1550

■

Maximum Operating Range (kilometers)Nominal Wavelength (nm)Fiber Type

10 (6.2 miles), matching SFP must have the same operating range

40 (24.85 miles), matching SFP must have the same operating range

GE 1000Base-SX Module Combination (1 Port) (256-MB Memory) ■ 29

ERX 11.1.x Module Guide

GE 1000Base-LH Module Combination (1 Port) (256-MB Memory)

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

GE/FE

GE I/O SFP

1 active, 1 redundant

■

First supported: 5.0.0

■

Final supported: Not applicable

■

130 W

■

Gigabit Ethernet

■

256 MB of memory

■

The 128-MB version has reached end-of-life.

■

The I/O module uses a range of small form-factor pluggable (SFP) transceivers to

■

support different modes and cabling distances.

Uses either optical or copper SFPs.

■

The optical transceivers are 1000Base-LX/LH compliant.

■

The copper transceivers are 1000Base-T compliant.

■

Single-strand SFPs can be used. These SFPs work in pairs and require a matching

■

SFP at the opposite end of the Ethernet connection. For example, an SFP rated at TX 1310, RX 1550 must be paired with an SFP rated TX 1550, RX 1310 with the same maximum operating range. See the following corresponding table (Single-strand SFPs Pairing) for more information.

EFA ASIC

■

Capability

Software features

Model compatibility

SRP module compatibility

Module redundancy support

Cables and connectors (copper SFP)

Ethernet (IEEE 802.3z)

■

1000Base-LH

■

See “Ethernet Modules” on page 112 for information about the layer 2 and layer 3

■

protocols and applications that this module combination supports.

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

Not applicable

■

Maximum range is 100 meters on CAT5 cable.

■

30 ■ GE 1000Base-LH Module Combination (1 Port) (256-MB Memory)

Cables and connectors (LX/LH)

LEDs

Alarms, errors, and events

GE 1000Base-LH Module Combination (1 Port) (256-MB Memory)

LC full duplex

■

Tx power:

■

min: –9.5 dBm

■

max: –3 dBm

■

Center wavelength: 1300 nm

■

Rx input power:

■

min: –20 dBm

■

max: –3 dBm

■

Rated for 10 km (6.2 miles) over 10-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring Ethernet Interfaces in JUNOSe Physical Layer Configuration Guide,

■

Chapter 5, Configuring Ethernet Interfaces.

Table 3: Single-strand SFPs Pairing

9 microns

TX 1310, RX 1550

■

Pairs with TX 1550 / RX 1310

■

TX 1550 / RX 1310

■

Pairs with TX 1310, RX 1550

■

TX 1310, RX 1490

■

Pairs with TX 1490 / RX 1310

■

TX 1490 / RX 1310

■

Pairs with TX 1310, RX 1490

■

TX 1310, RX 1550

■

Pairs with TX 1550 / RX 1310

■

TX 1550, RX 1310

■

Pairs with TX 1310 / RX 1550

■

Maximum Operating Range (kilometers)Nominal Wavelength (nm)Fiber Type

10 (6.2 miles), matching SFP must have the same operating range

40 (24.85 miles), matching SFP must have the same operating range

GE 1000Base-LH Module Combination (1 Port) (256-MB Memory) ■ 31

ERX 11.1.x Module Guide

GE 1000Base-ZX Module Combination (1 Port) (256-MB Memory)

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

GE/FE

GE I/O SFP

1 active, 1 redundant

■

First supported: 5.0.0

■

Final supported: Not applicable

■

130 W

■

Gigabit Ethernet

■

256 MB of memory

■

The 128-MB version has reached end-of-life.

■

The I/O module uses a range of small form-factor pluggable (SFP) transceivers to

■

support different modes and cabling distances.

Uses either optical or copper SFPs.

■

The optical transceivers are 1000Base-ZX compliant.

■

The copper transceivers are 1000Base-T compliant.

■

Single-strand SFPs can be used. These SFPs work in pairs and require a matching

■

SFP at the opposite end of the Ethernet connection. For example, an SFP rated at TX 1310, RX 1550 must be paired with an SFP rated TX 1550, RX 1310 with the same maximum operating range. See the following corresponding table (Single-strand SFPs Pairing) for more information.

EFA ASIC

■

Capability

Software features

Model compatibility

SRP module compatibility

Module redundancy support

Cables and connectors (copper SFP)

Ethernet (IEEE 802.3z)

■

1000Base-ZX

■

See “Ethernet Modules” on page 112 for information about the layer 2 and layer 3

■

protocols and applications that this module combination supports.

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

Not applicable

■

Maximum range is 100 meters on CAT5 cable.

■

32 ■ GE 1000Base-ZX Module Combination (1 Port) (256-MB Memory)

Cables and connectors (ZX)

LEDs

Alarms, errors, and events

GE 1000Base-ZX Module Combination (1 Port) (256-MB Memory)

LC full duplex

■

Tx power:

■

min: –2 dBm

■

max: 3 dBm

■

Center wavelength: 1550 nm

■

Rx input power:

■

min: –22 dBm

■

max: –3 dBm

■

Rated for 70 km (43.4 miles) over 10-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring Ethernet Interfaces in JUNOSe Physical Layer Configuration Guide,

■

Chapter 5, Configuring Ethernet Interfaces.

Table 4: Single-strand SFPs Pairing

9 microns

TX 1310, RX 1550

■

Pairs with TX 1550 / RX 1310

■

TX 1550 / RX 1310

■

Pairs with TX 1310, RX 1550

■

TX 1310, RX 1490

■

Pairs with TX 1490 / RX 1310

■

TX 1490 / RX 1310

■

Pairs with TX 1310, RX 1490

■

TX 1310, RX 1550

■

Pairs with TX 1550 / RX 1310

■

TX 1550, RX 1310

■

Pairs with TX 1310 / RX 1550

■

Maximum Operating Range (kilometers)Nominal Wavelength (nm)Fiber Type

10 (6.2 miles), matching SFP must have the same operating range

40 (24.85 miles), matching SFP must have the same operating range

GE 1000Base-ZX Module Combination (1 Port) (256-MB Memory) ■ 33

ERX 11.1.x Module Guide

GE Multimode Module Combination (1 Port)

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

Model compatibility

GE/FE

GE I/O

MULTI MODE

1 active, 1 redundant

■

First supported: 2.0.0

■

Final supported: Not applicable

■

130 W

■

Gigabit Ethernet

■

This module combination has been superseded by a newer assembly; however,

■

it is supported by current software.

EFA ASIC

■

Ethernet (IEEE 802.3z)

■

See “Ethernet Modules” on page 112 for information about the layer 2 and layer

■

3 protocols and applications that this module combination supports.

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP module compatibility

Module redundancy support

Cables and connectors

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

Not applicable

■

SC full duplex

■

Tx power:

■

min: –9.5 dBm

■

max: –4 dBm

■

Center wavelength: 850 nm

■

Rx input power:

■

min: –17 dBm

■

max: –3 dBm

■

Rated for 275 m (300 yards) over 62.5-micron core cable

■

Rated for 550 m (601 yards) over 50-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

34 ■ GE Multimode Module Combination (1 Port)

LEDs

Alarms, errors, and events

GE Multimode Module Combination (1 Port)

See “Module LEDs” on page 133.

■

See Monitoring Ethernet Interfaces in JUNOSe Physical Layer Configuration Guide,

■

Chapter 5, Configuring Ethernet Interfaces.

GE Multimode Module Combination (1 Port) ■ 35

ERX 11.1.x Module Guide

GE Single-Mode Module Combination (1 Port)

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

Model compatibility

GE/FE

GE I/O

SINGLE MODE

1 active, 1 redundant

■

First supported: 2.0.0

■

Final supported: Not applicable

■

130 W

■

Gigabit Ethernet

■

This module combination has been superseded by a newer assembly; however,

■

it is supported by current software.

EFA ASIC

■

Ethernet (IEEE 802.3z)

■

See “Ethernet Modules” on page 112 for information about the layer 2 and layer

■

3 protocols and applications that this module combination supports.

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP module compatibility

Module redundancy support

Cables and connectors

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

Not applicable

■

SC full duplex

■

Tx power:

■

min: –11 dBm

■

max: –3 dBm

■

Center wavelength: 1300 nm

■

Rx input power:

■

min: –20 dBm

■

max: –3 dBm

■

Rated for 550 m (601 yards) over 62.5-micron core or 50-micron core MM fiber

■

Rated for 5 km (3.1 miles) over 10-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

36 ■ GE Single-Mode Module Combination (1 Port)

LEDs

Alarms, errors, and events

GE Single-Mode Module Combination (1 Port)

See “Module LEDs” on page 133.

■

See Monitoring Ethernet Interfaces in JUNOSe Physical Layer Configuration Guide,

■

Chapter 5, Configuring Ethernet Interfaces.

GE Single-Mode Module Combination (1 Port) ■ 37

ERX 11.1.x Module Guide

GE2 1000Base-SX Module Combination (2 Ports)

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

GE-2

GE-2 SFP I/O or 2XGE APS I/O SFP or GE-2 APS I/O SFP

2 active, 2 redundant

■

First supported: 5.3.0

■

Final supported: Not applicable

■

100 W

■

Gigabit Ethernet

■

The I/O module uses a range of small form-factor pluggable (SFP) transceivers to

■

support different modes and cabling distances.

Uses either optical or copper SFPs.

■

The optical transceivers are 1000Base-SX compliant.

■

The copper transceivers are 1000Base-T compliant.

■

Single-strand SFPs can be used. These SFPs work in pairs and require a matching SFP

■

at the opposite end of the Ethernet connection. For example, an SFP rated at TX 1310, RX 1550 must be paired with an SFP rated TX 1550, RX 1310 with the same maximum operating range. See the following corresponding table (Single-strand SFPs Pairing) for more information.

For information about bandwidth and line rate considerations for the GE2 1000Base-SX

■

module combination, see GE–2 SFP I/O Module in JUNOSe Physical Layer Configuration Guide, Chapter 5, Configuring Ethernet Interfaces.

FFA ASIC

■

Capability

Software features

Model compatibility

SRP module compatibility

Module redundancy support

Cables and connectors (copper SFP)

Ethernet (IEEE 802.3z)

■

1000Base-SX

■

See “Ethernet Modules” on page 112 for information about the layer 2 and layer 3

■

protocols and applications that this module combination supports.

ERX1440 router

■

ERX310 router

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

Not applicable

■

Maximum range is 100 meters on CAT5 cable.

■

38 ■ GE2 1000Base-SX Module Combination (2 Ports)

Cables and connectors (SX)

LEDs

Alarms, errors, and events

GE2 1000Base-SX Module Combination (2 Ports)

LC full duplex

■

Tx power:

■

min: –9.5 dBm

■

max: –4 dBm

■

Center wavelength: 850 nm

■

Rx input power:

■

min: –17 dBm

■

max: –3 dBm

■

Rated for 275 m (300 yards) over 62.5-micron core cable

■

Rated for 550 m (601 yards) over 50-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring Ethernet Interfaces in JUNOSe Physical Layer Configuration Guide,

■

Chapter 5, Configuring Ethernet Interfaces.

Table 5: Single-strand SFPs Pairing

9 microns

TX 1310, RX 1550

■

Pairs with TX 1550 / RX 1310

■

TX 1550 / RX 1310

■

Pairs with TX 1310, RX 1550

■

TX 1310, RX 1490

■

Pairs with TX 1490 / RX 1310

■

TX 1490 / RX 1310

■

Pairs with TX 1310, RX 1490

■

TX 1310, RX 1550

■

Pairs with TX 1550 / RX 1310

■

TX 1550, RX 1310

■

Pairs with TX 1310 / RX 1550

■

Maximum Operating Range (kilometers)Nominal Wavelength (nm)Fiber Type

10 (6.2 miles), matching SFP must have the same operating range

40 (24.85 miles), matching SFP must have the same operating range

GE2 1000Base-SX Module Combination (2 Ports) ■ 39

ERX 11.1.x Module Guide

GE2 1000Base-LH Module Combination (2 Ports)

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

GE-2

GE-2 SFP I/O or 2XGE APS I/O SFP or GE-2 APS I/O SFP

2 active, 2 redundant

■

First supported: 5.3.0

■

Final supported: Not applicable

■

100 W

■

Gigabit Ethernet

■

The I/O module uses a range of small form-factor pluggable (SFP) transceivers to

■

support different modes and cabling distances.

Uses either optical or copper SFPs.

■

The optical transceivers are 1000Base-LX/LH compliant.

■

The copper transceivers are 1000Base-T compliant.

■

Single-strand SFPs can be used. These SFPs work in pairs and require a matching SFP

■

at the opposite end of the Ethernet connection. For example, an SFP rated at TX 1310, RX 1550 must be paired with an SFP rated TX 1550, RX 1310 with the same maximum operating range. See the following corresponding table (Single-strand SFPs Pairing) for more information.

For information about bandwidth and line rate considerations for the GE2 1000Base-LH

■

module combination, see GE–2 SFP I/O Module in JUNOSe Physical Layer Configuration Guide, Chapter 5, Configuring Ethernet Interfaces.

FFA ASIC

■

Capability

Software features

Model compatibility

SRP module compatibility

Module redundancy support

Cables and connectors (copper SFP)

Ethernet (IEEE 802.3z)

■

1000Base-LH

■

See “Ethernet Modules” on page 112 for information about the layer 2 and layer 3

■

protocols and applications that this module combination supports.

ERX1440 router

■

ERX310 router

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

Not applicable

■

Maximum range is 100 meters on CAT5 cable.

■

40 ■ GE2 1000Base-LH Module Combination (2 Ports)

Cables and connectors (LX/LH)

Cables and connectors (single–mode LX40)

GE2 1000Base-LH Module Combination (2 Ports)

LC full duplex

■

Tx power:

■

min: –9.5 dBm

■

max: –3 dBm

■

Center wavelength: 1300 nm

■

Rx input power:

■

min: –20 dBm

■

max: –3 dBm

■

Rated for 10 km (6.2 miles) over 9-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

LC full duplex

■

Tx power:

■

min: –4.5 dBm

■

max: 0 dBm

■

Center wavelength: 1300 nm

■

Rx input power:

■

min: –35 dBm

■

max: –22.5 dBm

■

Rated for 40 km (24.85 miles) over 9-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

LEDs

Alarms, errors, and events

See “Module LEDs” on page 133.

■

See Monitoring Ethernet Interfaces in JUNOSe Physical Layer Configuration Guide,

■

Chapter 5, Configuring Ethernet Interfaces.

Table 6: Single-strand SFPs Pairing

9 microns

TX 1310, RX 1550

■

Pairs with TX 1550 / RX 1310

■

TX 1550 / RX 1310

■

Pairs with TX 1310, RX 1550

■

TX 1310, RX 1490

■

Pairs with TX 1490 / RX 1310

■

TX 1490 / RX 1310

■

Pairs with TX 1310, RX 1490

■

TX 1310, RX 1550

■

Pairs with TX 1550 / RX 1310

■

Maximum Operating Range (kilometers)Nominal Wavelength (nm)Fiber Type

10 (6.2 miles), matching SFP must have the same operating range

40 (24.85 miles), matching SFP must have the same operating range

9 microns

TX 1550, RX 1310

■

Pairs with TX 1310 / RX 1550

■

GE2 1000Base-LH Module Combination (2 Ports) ■ 41

40 (24.85 miles), matching SFP must have the same operating range

ERX 11.1.x Module Guide

GE2 1000Base-ZX Module Combination (2 Ports)

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

GE-2

GE-2 SFP I/O or 2XGE APS I/O SFP or GE-2 APS I/O SFP

2 active, 2 redundant

■

First supported: 5.3.0

■

Final supported: Not applicable

■

100 W

■

Gigabit Ethernet

■

The I/O module uses a range of small form-factor pluggable (SFP) transceivers to support

■

different modes and cabling distances.

Uses either optical or copper SFPs.

■

The optical transceivers are 1000Base-ZX compliant.

■

The copper transceivers are 1000Base-T compliant.

■

Single-strand SFPs can be used. These SFPs work in pairs and require a matching SFP

■

at the opposite end of the Ethernet connection. For example, an SFP rated at TX 1310, RX 1550 must be paired with an SFP rated TX 1550, RX 1310 with the same maximum operating range. See the following corresponding table (Single-strand SFPs Pairing) for more information.

For information about bandwidth and line rate considerations for the GE2 1000Base-ZX

■

module combination, see GE-2 SFP I/O Module in JUNOSe Physical Layer Configuration Guide, Chapter 5, Configuring Ethernet Interfaces.

FFA ASIC

■

Capability

Software features

Model compatibility

SRP module compatibility

Module redundancy support

Ethernet (IEEE 802.3z)

■

1000Base-ZX

■

See “Ethernet Modules” on page 112 for information about the layer 2 and layer 3

■

protocols and applications that this module combination supports.

ERX1440 router

■

ERX310 router

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

Not applicable

■

42 ■ GE2 1000Base-ZX Module Combination (2 Ports)

Cables and connectors

LEDs

Alarms, errors, and events

GE2 1000Base-ZX Module Combination (2 Ports)

LC full duplex

■

Tx power:

■

min: –3 dBm

■

max: 2 dBm

■

Center wavelength: 1550 nm

■

Rx input power:

■

min: –23 dBm

■

max: –3 dBm

■

Rated for 70 km (43.4 miles) over 10-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring Ethernet Interfaces in JUNOSe Physical Layer Configuration Guide, Chapter 5,

■

Configuring Ethernet Interfaces.

Table 7: Single-strand SFPs Pairing

9 microns

TX 1310, RX 1550

■

Pairs with TX 1550 / RX 1310

■

TX 1550 / RX 1310

■

Pairs with TX 1310, RX 1550

■

TX 1310, RX 1490

■

Pairs with TX 1490 / RX 1310

■

TX 1490 / RX 1310

■

Pairs with TX 1310, RX 1490

■

TX 1310, RX 1550

■

Pairs with TX 1550 / RX 1310

■

TX 1550, RX 1310

■

Pairs with TX 1310 / RX 1550

■

Maximum Operating Range (kilometers)Nominal Wavelength (nm)Fiber Type

10 (6.2 miles), matching SFP must have the same operating range

40 (24.85 miles), matching SFP must have the same operating range

GE2 1000Base-ZX Module Combination (2 Ports) ■ 43

ERX 11.1.x Module Guide

GE High Density (HDE) Module Combination (2 Ports)

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

GE-HDE

GE-2 SFP I/O or 2XGE APS I/O SFP or GE-2 APS I/O SFP

2 active, 2 redundant

■

First supported: 7.0.0

■

Final supported: Not applicable

■

100 W

■

Gigabit Ethernet

■

The I/O module uses a range of small form-factor pluggable (SFP) transceivers to

■

support different modes and cabling distances.

Uses either optical or copper SFPs.

■

The optical transceivers are 1000Base-LX/LH compliant.

■

The copper transceivers are 1000Base-T compliant.

■

Single-strand SFPs can be used. These SFPs work in pairs and require a matching SFP

■

at the opposite end of the Ethernet connection. For example, an SFP rated at TX 1310, RX 1550 must be paired with an SFP rated TX 1550, RX 1310 with the same maximum operating range. See the following corresponding table (Single-strand SFPs Pairing) for more information.

For information about bandwidth and line rate considerations for the GE–HDE module

■

combination, see GE-2 SFP I/O Module in JUNOSe Physical Layer Configuration Guide, Chapter 5, Configuring Ethernet Interfaces.

FFA ASIC

■

Capability

Software features

Model compatibility

SRP module compatibility

Module redundancy support

Cables and connectors (copper SFP)

Ethernet (IEEE 802.3z)

■

1000Base-LH

■

See “Ethernet Modules” on page 112 for information about the layer 2 and layer 3

■

protocols and applications that this module combination supports.

ERX1440 router

■

ERX310 router

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

Not applicable

■

Maximum range is 100 meters on CAT5 cable.

■

44 ■ GE High Density (HDE) Module Combination (2 Ports)

Cables and connectors (LX/LH)

Cables and connectors (single-mode LX40)

GE High Density (HDE) Module Combination (2 Ports)

LC full duplex

■

Tx power:

■

min: –9.5 dBm

■

max: –3 dBm

■

Center wavelength: 1300 nm

■

Rx input power:

■

min: –20 dBm

■

max: –3 dBm

■

Rated for 10 km (6.2 miles) over 10-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

LC full duplex

■

Tx power:

■

min: –4.5 dBm

■

max: 0 dBm

■

Center wavelength: 1300 nm

■

Rx input power:

■

min: –35 dBm

■

max: –22.5 dBm

■

Rated for 40 km (24.85 miles) over 10-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

LEDs

Alarms, errors, and events

See “Module LEDs” on page 133.

■

See Monitoring Ethernet Interfaces in JUNOSe Physical Layer Configuration Guide,

■

Chapter 5, Configuring Ethernet Interfaces.

Table 8: Single-strand SFPs Pairing

9 microns

TX 1310, RX 1550

■

Pairs with TX 1550 / RX 1310

■

TX 1550 / RX 1310

■

Pairs with TX 1310, RX 1550

■

TX 1310, RX 1490

■

Pairs with TX 1490 / RX 1310

■

TX 1490 / RX 1310

■

Pairs with TX 1310, RX 1490

■

TX 1310, RX 1550

■

Pairs with TX 1550 / RX 1310

■

Maximum Operating Range (kilometers)Nominal Wavelength (nm)Fiber Type

10 (6.2 miles), matching SFP must have the same operating range

40 (24.85 miles), matching SFP must have the same operating range

9 microns

TX 1550, RX 1310

■

Pairs with TX 1310 / RX 1550

■

GE High Density (HDE) Module Combination (2 Ports) ■ 45

40 (24.85 miles), matching SFP must have the same operating range

ERX 11.1.x Module Guide

GE High Density (HDE) Module Combination (8 Ports)

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

GE-HDE

GE-8 I/O

8

■

First supported: 7.0.0

■

Final supported: Not applicable

■

100 W

■

Gigabit Ethernet

■

The I/O module uses a range of small form-factor pluggable (SFP) transceivers to support

■

different modes and cabling distances.

Uses either optical or copper SFPs.

■

The optical transceivers are 1000Base-LX/LH compliant.

■

The copper transceivers are 1000Base-T compliant.

■

Single-strand SFPs can be used. These SFPs work in pairs and require a matching SFP

■

at the opposite end of the Ethernet connection. For example, an SFP rated at TX 1310, RX 1550 must be paired with an SFP rated TX 1550, RX 1310 with the same maximum operating range. See the following corresponding table (Single-strand SFPs Pairing) for more information.

For information about bandwidth and line rate considerations for the GE–HDE module

■

combination, see GE-8 I/O Module in JUNOSe Physical Layer Configuration Guide, Chapter 5, Configuring Ethernet Interfaces.

FFA ASIC

■

Capability

Software features

Model compatibility

SRP module compatibility

Module redundancy support

Ethernet (IEEE 802.3z)

■

1000Base-LH

■

See “Ethernet Modules” on page 112 for information about the layer 2 and layer 3

■

protocols and applications that this module combination supports.

ERX1440 router

■

ERX310 router

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

Not applicable

■

46 ■ GE High Density (HDE) Module Combination (8 Ports)

Cables and connectors

Cables and connectors (single-mode LX40)

GE High Density (HDE) Module Combination (8 Ports)

LC full duplex

■

Tx power:

■

min: –9.5 dBm

■

max: –3 dBm

■

Center wavelength: 1300 nm

■

Rx input power:

■

min: –20 dBm

■

max: –3 dBm

■

Rated for 10 km (6.2 miles) over 10-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

LC full duplex

■

Tx power:

■

min: –4.5 dBm

■

max: 0 dBm

■

Center wavelength: 1300 nm

■

Rx input power:

■

min: –35 dBm

■

max: –22.5 dBm

■

Rated for 40 km (24.85 miles) over 9-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

LEDs

Alarms, errors, and events

See “Module LEDs” on page 133.

■

See Monitoring Ethernet Interfaces in JUNOSe Physical Layer Configuration Guide,

■

Chapter 5, Configuring Ethernet Interfaces.

Table 9: Single-strand SFPs Pairing

9 microns

TX 1310, RX 1550

■

Pairs with TX 1550 / RX 1310

■

TX 1550 / RX 1310

■

Pairs with TX 1310, RX 1550

■

TX 1310, RX 1490

■

Pairs with TX 1490 / RX 1310

■

TX 1490 / RX 1310

■

Pairs with TX 1310, RX 1490

■

TX 1310, RX 1550

■

Pairs with TX 1550 / RX 1310

■

Maximum Operating Range (kilometers)Nominal Wavelength (nm)Fiber Type

10 (6.2 miles), matching SFP must have the same operating range

40 (24.85 miles), matching SFP must have the same operating range

9 microns

TX 1550, RX 1310

■

Pairs with TX 1310 / RX 1550

■

GE High Density (HDE) Module Combination (8 Ports) ■ 47

40 (24.85 miles), matching SFP must have the same operating range

ERX 11.1.x Module Guide

IPSec Service Module Combination

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

Model compatibility

SRP module compatibility

IPSEC SERVICE

No I/O module

Not applicable

■

First supported: 4.0.2

■

Final supported: Not applicable

■

130 W

■

IPSec Tunnel Service

■

EFA ASIC

■

IPSec tunnels

■

See “Service Modules” on page 125 for information about the layer 2 and

■

layer 3 protocols and applications that this module combination supports.

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

Module redundancy support

Cables and connectors

LEDs

Alarms, errors, and events

48 ■ IPSec Service Module Combination

Multiple IPSec Service modules provide redundancy.

■

Not applicable

■

See “Module LEDs” on page 133.

■

See Monitoring Tunnel-Service Interfaces in JUNOSe Physical Layer

■

Configuration Guide, Chapter 6, Managing Tunnel-Service and IPSec-Service Interfaces.

OC3/STM1 ATM Multimode Without APS/MSP Redundancy Module Combination (256-MB Memory)

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

Model compatibility

OCx/STMx ATM or OCx/STMx /DS3-ATM

OC3-4 I/O

MULTI MODE

4

■

First supported: 5.0.0, 5.3.0 or a higher-numbered release

■

Final supported: Not applicable

■

130 W

■

256 MB of memory

■

The 128-MB version has reached end-of-life.

■

Unchannelized, concatenated OC3/STM1 for ATM

■

EFA ASIC

■

OC3/STM1

■

ATM:AAL5

■

See “OCx/STMx ATM Modules” on page 120 for information about the layer 2 and

■

layer 3 protocols and applications that this module combination supports.

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP module compatibility

Module redundancy support

OC3/STM1 ATM Multimode Without APS/MSP Redundancy Module Combination (256-MB Memory) ■ 49

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

1:N redundancy

■

NOTE: Line module redundancy is not supported on the ERX310 router.

■

ERX 11.1.x Module Guide

Cables and connectors

LEDs

Alarms, errors, and events

SC full duplex connector

■

Tx power:

■

min: –19 dBm

■

max: –14 dBm

■

Center wavelength: 1310 nm

■

Rx input power:

■

min: –30 dBm

■

max: –14 dBm

■

Rated for 2 km (1.2 miles) over 62.5-micron core cable with an optical loss of 0–9

■

dB or 50-micron core cable with an optical loss of 7 dB

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring SONET/SDH Interfaces in JUNOSe Physical Layer Configuration Guide,

■

Chapter 3, Configuring Unchannelized OCx/STMx Interfaces.

50 ■ OC3/STM1 ATM Multimode Without APS/MSP Redundancy Module Combination (256-MB Memory)

OC3/STM1 ATM Multimode With APS/MSP Redundancy Module Combination

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

OCx/STMx ATM or OCx/STMx /DS3-ATM

4XOC3

APS I/O

MULTI MODE

4 active, 4 redundant

■

First supported: 5.1.2, 5.2.0 (APS/MSP)

■

Final supported: Not applicable

■

The OCx/STMx ATM line module or the OCx/STMx /DS3-ATM line module must have

■

a minimum of 256 MB of memory to be used with JUNOSe Release 5.3.0 or a higher-numbered release.

130 W

■

Can use either the 128-MB OCx/STMx ATM line module or the 256-MB OCx/STMx

■

/DS3-ATM line module.

Unchannelized, concatenated OC3/STM1 for ATM

■

EFA ASIC

■

OC3/STM-1

■

ATM/AAL5

■

Software features

Model compatibility

SRP module compatibility

Module redundancy support

See “OCx/STMx ATM Modules” on page 120 for information about the layer 2 and

■

layer 3 protocols and applications that this module combination supports.

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

1:N redundancy

■

NOTE: Line module redundancy is not supported on the ERX310 router.

■

OC3/STM1 ATM Multimode With APS/MSP Redundancy Module Combination ■ 51

ERX 11.1.x Module Guide

Cables and connectors

LEDs

Alarms, errors, and events

LC full duplex

■

Tx power:

■

min: –19 dBm

■

max: –14 dBm

■

Center wavelength: 1310 nm

■

Rx input power:

■

min: –30 dBm

■

max: –14 dBm

■

Rated for 2 km (1.2 miles) over 62.5-micron core cable with an optical loss of 0–9

■

dB or 50-micron core cable with an optical loss of 7 dB

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring SONET/SDH Interfaces in JUNOSe Physical Layer Configuration Guide,

■

Chapter 3, Configuring Unchannelized OCx/STMx Interfaces.

52 ■ OC3/STM1 ATM Multimode With APS/MSP Redundancy Module Combination

OC3/STM1 ATM Single-Mode Intermediate Reach Without APS/MSP Redundancy Module Combination (256-MB Memory)

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

Model compatibility

OCx/STMx ATM or OCx/STMx /DS3-ATM

OC3-4 I/O

SINGLE MODE

4

■

First supported: 5.0.0, 5.3.0 or a higher-numbered release

■

Final supported: Not applicable

■

130 W

■

256 MB of memory

■

The 128-MB version has reached end-of-life.

■

Unchannelized, concatenated OC3/STM1 for ATM

■

EFA ASIC

■

OC3/STM1

■

ATM/AAL5

■

See “OCx/STMx ATM Modules” on page 120 for information about the layer 2 and

■

layer 3 protocols and applications that this module combination supports.

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP-5G+

SRP module compatibility

Module redundancy support

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

1:N redundancy

■

NOTE: Line module redundancy is not supported on the ERX310 router.

■

OC3/STM1 ATM Single-Mode Intermediate Reach Without APS/MSP Redundancy Module Combination (256-MB Memory) ■ 53

ERX 11.1.x Module Guide

Cables and connectors

LEDs

Alarms, errors, and events

SC full duplex

■

Tx power:

■

min: –15 dBm

■

max: –8 dBm

■

Center wavelength: 1310 nm

■

Rx input power:

■

min: –31 dBm

■

max: –8 dBm

■

Rated for 15 km (9.3 miles) of 9-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring SONET/SDH Interfaces in JUNOSe Physical Layer Configuration Guide,

■

Chapter 3, Configuring Unchannelized OCx/STMx Interfaces.

54 ■ OC3/STM1 ATM Single-Mode Intermediate Reach Without APS/MSP Redundancy Module Combination (256-MB Memory)

OC3/STM1 ATM Single-Mode Intermediate Reach With APS/MSP Redundancy Module Combination

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

OCx/STMx ATM or OCx/STMx /DS3-ATM

4XOC3

APS I/O

SINGLE MODE

4 active, 4 redundant

■

First supported: 5.1.2, 5.2.0 (APS/MSP)

■

Final supported: Not applicable

■

The OCx/STMx ATM line module or the OCx/STMx /DS3-ATM line module must have

■

a minimum of 256 MB of memory to be used with JUNOSe Release 5.3.0 or a higher-numbered release.

130 W

■

Can use either the 128-MB OCx/STMx ATM line module or the 256-MB OCx/STMx

■

/DS3-ATM line module.

Unchannelized, concatenated OC3/STM1 for ATM

■

EFA ASIC

■

OC3/STM-1

■

ATM/AAL5

■

Software features

Model compatibility

SRP module compatibility

Module redundancy support

See “OCx/STMx ATM Modules” on page 120 for information about the layer 2 and

■

layer 3 protocols and applications that this module combination supports.

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

1:N redundancy

■

NOTE: Line module redundancy is not supported on the ERX310 router.

■

OC3/STM1 ATM Single-Mode Intermediate Reach With APS/MSP Redundancy Module Combination ■ 55

ERX 11.1.x Module Guide

Cables and connectors

LEDs

Alarms, errors, and events

LC full duplex

■

Tx power:

■

min: –15 dBm

■

max: –8 dBm

■

Center wavelength: 1310 nm

■

Rx input power:

■

min: –31 dBm

■

max: –8 dBm

■

Rated for 15 km (9.3 miles) of 9-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring SONET/SDH Interfaces in JUNOSe Physical Layer Configuration Guide,

■

Chapter 3, Configuring Unchannelized OCx/STMx Interfaces.

56 ■ OC3/STM1 ATM Single-Mode Intermediate Reach With APS/MSP Redundancy Module Combination

OC3/STM1 ATM Single-Mode Long Reach Without APS/MSP Redundancy Module Combination (256-MB Memory)

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

Model compatibility

OCx/STMx ATM or OCx/STMx /DS3-ATM

OC3-4 I/O

LONG HAUL

4

■

First supported: 5.0.0, 5.3.0 or a higher-numbered release

■

Final supported: Not applicable

■

130 W

■

256 MB of memory

■

The 128-MB version has reached end-of-life.

■

Unchannelized, concatenated OC3/STM1 for ATM

■

EFA ASIC

■

OC3/STM1

■

ATM/AAL5

■

See “OCx/STMx ATM Modules” on page 120 for information about the layer 2 and

■

layer 3 protocols and applications that this module combination supports.

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP-5G+

SRP module compatibility

Module redundancy support

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

1:N redundancy

■

NOTE: Line module redundancy is not supported on the ERX310 router.

■

OC3/STM1 ATM Single-Mode Long Reach Without APS/MSP Redundancy Module Combination (256-MB Memory) ■ 57

ERX 11.1.x Module Guide

Cables and connectors

LEDs

Alarms, errors, and events

SC full duplex

■

Tx power:

■

min: –5.0 dBm

■

max: 0 dBm

■

Center wavelength: 1310 nm

■

Rx input power:

■

min: –34 dBm

■

max: –7 dBm

■

Rated for 40 km (24.8 miles) of 9-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring SONET/SDH Interfaces in JUNOSe Physical Layer Configuration Guide,

■

Chapter 3, Configuring Unchannelized OCx/STMx Interfaces.

58 ■ OC3/STM1 ATM Single-Mode Long Reach Without APS/MSP Redundancy Module Combination (256-MB Memory)

OC3/STM1 GE/FE Module Combination

Line module label

I/O module label

Number of I/O ports

Software release

Description

OC3/STM1 GE/FE

OC3-2 GE APS I/O

3; one active and one redundant port per SFP

■

Ports 0 and 1—ATM interfaces

■

Port 2—GE interface

■

Port redundancy is not supported.

■

First supported: 6.1.0

■

Final supported: Not applicable

■

150 W

■

Unchannelized OC3/STM1 ATM operation via two line interfaces

■

and

Gigabit Ethernet operation via one line interface

■

The I/O module uses a range of small form-factor pluggable (SFP) transceivers to support

■

different modes and cabling distances.

Depending on the configuration, a variety of SFP combinations can occur.

■

The OC3-2 GE APS I/O module accepts up to three LC-style fiber-optic or copper SFPs.

■

Single-strand SFPs can be used. These SFPs work in pairs and require a matching SFP

■

at the opposite end of the Ethernet connection. For example, an SFP rated at TX 1310, RX 1550 must be paired with an SFP rated TX 1550, RX 1310 with the same maximum operating range. See the following table (Single-strand SFPs Pairing) for more information.

Type

Capability

Software features

Model compatibility

SRP module compatibility

Module redundancy support

EFA ASIC

■

OC3/STM1

■

ATM/AAL5

■

Ethernet (IEEE 802.3x)

■

1000Base-LX/SX/ZX

■

See “OCx/STMx GE/FE Modules” on page 118 for information about the layer 2 and layer

■

3 protocols and applications that this module combination supports.

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

Not applicable

■

OC3/STM1 GE/FE Module Combination ■ 59

ERX 11.1.x Module Guide

Cables and connectors (ATM LX)

Cables and connectors (ATM SX)

LC-style fiber-optic connectors

■

Tx power:

■

min: –19.0 dBm

■

max: –14dBm

■

Center wavelength: 1310 nm

■

Rx input power:

■

min: –30 dBm

■

max: –14 dBm

■

Rated for 2 km (1.2 miles) over 62.5-micron core cable with an optical loss of 0–9db or

■

over 50-micron core cable with an optical loss of 7 db

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

LC-style fiber-optic connectors

■

Tx power:

■

min: –15.0 dBm

■

max: –8 dBm

■

Center wavelength: 1310 nm

■

Rx input power:

■

min: –31 dBm

■

max: –8 dBm

■

Rated for 15 km (9.3 miles) of 9-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

Cables and connectors (ATM ZX)

Cables and connectors (GE LX)

LC-style fiber-optic connectors

■

Tx power:

■

min: –5.0 dBm

■

max: 0 dBm

■

Center wavelength: 1310 nm

■

Rx input power:

■

min: –34 dBm

■

max: –7 dBm

■

Rated for 40 km (24.8 miles) of 9-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

LC full duplex

■

Tx power:

■

min: –9.5 dBm

■

max: –3 dBm

■

Center wavelength: 1300 nm

■

Rx input power:

■

min: –20 dBm

■

max: –3 dBm

■

Rated for 10 km (6.2 miles) over 10-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

60 ■ OC3/STM1 GE/FE Module Combination

Cables and connectors (GE single–mode LX40)

Cables and connectors (GE SX)

OC3/STM1 GE/FE Module Combination

LC full duplex

■

Tx power:

■

min: –4.5 dBm

■

max: –0 dBm

■

Center wavelength: 1300 nm

■

Rx input power:

■

min: –35 dBm

■

max: –22.5 dBm

■

Rated for 40 km (28.85 miles) over 9-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

LC full duplex

■

Tx power:

■

min: –9.5 dBm

■

max: –4 dBm

■

Center wavelength: 850 nm

■

Rx input power:

■

min: –17 dBm

■

max: –3 dBm

■

Rated for 275 m (300 yards) over 62.5-micron core cable

■

Rated for 550 m (601 yards) over 50-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

Cables and connectors (GE ZX)

LEDs

Alarms, errors, and events

LC full duplex

■

Tx power:

■

min: –3 dBm

■

max: 2 dBm

■

Center wavelength: 1550 nm

■

Rx input power:

■

min: –23 dBm

■

max: –3 dBm

■

Rated for 70 km (43.4 miles) over 10-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring SONET/SDH Interfaces in JUNOSe Physical Layer Configuration Guide,

■

Chapter 3, Configuring Unchannelized OCx/STMx Interfaces.

Table 10: Single-strand SFPs Pairing

9 microns

TX 1310, RX 1550

■

Pairs with TX 1550 / RX 1310

■

Maximum Operating Range (kilometers)Nominal Wavelength (nm)Fiber Type

10 (6.2 miles), matching SFP must have the same operating range

OC3/STM1 GE/FE Module Combination ■ 61

ERX 11.1.x Module Guide

Table 10: Single-strand SFPs Pairing (continued)

9 microns

TX 1550 / RX 1310

■

Pairs with TX 1310, RX 1550

■

Maximum Operating Range (kilometers)Nominal Wavelength (nm)Fiber Type

10 (6.2 miles), matching SFP must have the same operating range

9 microns

TX 1310, RX 1490

■

Pairs with TX 1490 / RX 1310

■

TX 1490 / RX 1310

■

Pairs with TX 1310, RX 1490

■

TX 1310, RX 1550

■

Pairs with TX 1550 / RX 1310

■

TX 1550, RX 1310

■

Pairs with TX 1310 / RX 1550

■

10 (6.2 miles), matching SFP must have the same operating range

40 (24.85 miles), matching SFP must have the same operating range

62 ■ OC3/STM1 GE/FE Module Combination

OC3/STM1 POS Multimode Without APS/MSP Redundancy Module Combination

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

Model compatibility

OCx/STMx POS

OC3-4 I/O

MULTI MODE

4

■

First supported: 2.0.0

■

Final supported: Not applicable

■

120 W

■

Unchannelized, concatenated OC3/STM1 for POS

■

EFA ASIC

■

OC3/STM1

■

HDLC framing

■

See “OCx/STMx POS and OC48 Modules” on page 123 for information about the

■

layer 2 and layer 3 protocols and applications that this module combination supports.

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP module compatibility

Module redundancy support

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

1:N redundancy

■

NOTE: Line module redundancy is not supported on the ERX310 router.

■

OC3/STM1 POS Multimode Without APS/MSP Redundancy Module Combination ■ 63

ERX 11.1.x Module Guide

Cables and connectors

LEDs

Alarms, errors, and events

SC full duplex

■

Tx power:

■

min: –19 dBm

■

max: –14 dBm

■

Center wavelength: 1310 nm

■

Rx input power:

■

min: –30 dBm

■

max: –14 dBm

■

Rated for 2 km (1.2 miles) over 62.5-micron core cable with an optical loss of

■

0–9 dB or 50-micron core cable with an optical loss of 7 dB

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring SONET/SDH Interfaces in JUNOSe Physical Layer Configuration Guide,

■

Chapter 3, Configuring Unchannelized OCx/STMx Interfaces.

64 ■ OC3/STM1 POS Multimode Without APS/MSP Redundancy Module Combination

OC3/STM1 POS Multimode With APS/MSP Redundancy Module Combination

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

Model compatibility

OCx/STMx POS

4XOC3

APS I/O

MULTI MODE

4 active, 4 redundant

■

First supported: 5.1.2, 5.2.0 (APS/MSP)

■

Final supported: Not applicable

■

120 W

■

Unchannelized, concatenated OC3/STM1 for POS

■

EFA ASIC

■

OC3/STM-1

■

HDLC framing

■

See “OCx/STMx POS and OC48 Modules” on page 123 for information about the

■

layer 2 and layer 3 protocols and applications that this module combination supports.

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP module compatibility

Module redundancy support

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

1:N redundancy

■

NOTE: Line module redundancy is not supported on the ERX310 router.

■

OC3/STM1 POS Multimode With APS/MSP Redundancy Module Combination ■ 65

ERX 11.1.x Module Guide

Cables and connectors

LEDs

Alarms, errors, and events

LC full duplex

■

Tx power:

■

min: –19 dBm

■

max: –14 dBm

■

Center wavelength: 1310 nm

■

Rx input power:

■

min: –30 dBm

■

max: –14 dBm

■

Rated for 2 km (1.2 miles) over 62.5-micron core cable with an optical loss of 0–9

■

dB or 50-micron core cable with an optical loss of 7 dB

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring SONET/SDH Interfaces in JUNOSe Physical Layer Configuration Guide,

■

Chapter 3, Configuring Unchannelized OCx/STMx Interfaces.

66 ■ OC3/STM1 POS Multimode With APS/MSP Redundancy Module Combination

OC3/STM1 POS Single-Mode Intermediate Reach Without APS/MSP Redundancy Module Combination

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

Model compatibility

OCx/STMx POS

OC3-4 I/O

SINGLE MODE

4

■

First supported: 2.0.0

■

Final supported: Not applicable

■

120 W

■

Unchannelized, concatenated OC3/STM1 for POS

■

EFA ASIC

■

OC3/STM1

■

HDLC framing

■

See “OCx/STMx POS and OC48 Modules” on page 123 for information about the

■

layer 2 and layer 3 protocols and applications that this module combination supports.

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP module compatibility

Module redundancy support

Cables and connectors

OC3/STM1 POS Single-Mode Intermediate Reach Without APS/MSP Redundancy Module Combination ■ 67

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

1:N redundancy

■

NOTE: Line module redundancy is not supported on the ERX310 router.

■

SC full duplex

■

Tx power:

■

min: –15 dBm

■

max: –8 dBm

■

Center wavelength: 1310 nm

■

Rx input power:

■

min: –31 dBm

■

max: –8 dBm

■

Rated for 15 km (9.3 miles) of 9-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

ERX 11.1.x Module Guide

LEDs

Alarms, errors, and events

See “Module LEDs” on page 133.

■

See Monitoring SONET/SDH Interfaces in JUNOSe Physical Layer Configuration

■

Guide, Chapter 3, Configuring Unchannelized OCx/STMx Interfaces.

68 ■ OC3/STM1 POS Single-Mode Intermediate Reach Without APS/MSP Redundancy Module Combination

OC3/STM1 POS Single-Mode Intermediate Reach With APS/MSP Redundancy Module Combination

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

Model compatibility

OCx/STMx POS

4XOC3

APS I/O

SINGLE MODE

4 active, 4 redundant

■

First supported: 5.1.2, 5.2.0 (APS/MSP)

■

Final supported: Not applicable

■

120 W

■

Unchannelized, concatenated OC3/STM1 for POS

■

EFA ASIC

■

OC3/STM1

■

HDLC framing

■

See “OCx/STMx POS and OC48 Modules” on page 123 for information about the

■

layer 2 and layer 3 protocols and applications that this module combination supports.

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP module compatibility

Module redundancy support

OC3/STM1 POS Single-Mode Intermediate Reach With APS/MSP Redundancy Module Combination ■ 69

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

1:N redundancy

■

NOTE: Line module redundancy is not supported on the ERX310 router.

■

ERX 11.1.x Module Guide

Cables and connectors

LEDs

Alarms, errors, and events

LC full duplex

■

Tx power:

■

min: –15 dBm

■

max: –8 dBm

■

Center wavelength: 1310 nm

■

Rx input power:

■

min: –31 dBm

■

max: –8 dBm

■

Rated for 15 km (9.3 miles) of 9-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring SONET/SDH Interfaces in JUNOSe Physical Layer Configuration

■

Guide, Chapter 3, Configuring Unchannelized OCx/STMx Interfaces.

70 ■ OC3/STM1 POS Single-Mode Intermediate Reach With APS/MSP Redundancy Module Combination

OC3/STM1 POS Single-Mode Long Reach Module Combination

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

Model compatibility

OCx/STMx POS

OC3-4 I/O

LONG HAUL

4

■

First supported: 2.0.0

■

Final supported: Not applicable

■

120 W

■

Unchannelized, concatenated OC3/STM1 for POS

■

EFA ASIC

■

OC3/STM1

■

HDLC framing

■

See “OCx/STMx POS and OC48 Modules” on page 123 for information about the

■

layer 2 and layer 3 protocols and applications that this module combination supports.

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP module compatibility

Module redundancy support

Cables and connectors

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

1:N redundancy

■

NOTE: Line module redundancy is not supported on the ERX310 router.

■

SC full duplex

■

Tx power:

■

min: –5.0 dBm

■

max: 0 dBm

■

Center wavelength: 1310 nm

■

Rx input power:

■

min: –34 dBm

■

max: –7 dBm

■

Fiber type: 9-micron core

■

Rated for 40 km (24.8 miles) of 9-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

OC3/STM1 POS Single-Mode Long Reach Module Combination ■ 71

ERX 11.1.x Module Guide

LEDs

Alarms, errors, and events

See “Module LEDs” on page 133.

■

See Monitoring SONET/SDH Interfaces in JUNOSe Physical Layer Configuration

■

Guide, Chapter 3, Configuring Unchannelized OCx/STMx Interfaces.

72 ■ OC3/STM1 POS Single-Mode Long Reach Module Combination

OC12/STM4 ATM Multimode Without APS/MSP Redundancy Module Combination (256-MB Memory)

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

Model compatibility

OCx/STMx ATM or OCx/STMx /DS3-ATM

OC12 STM4 I/O

MULTI MODE

1

■

First supported: 5.0.0, 5.3.0 or a higher-numbered release

■

Final supported: Not applicable

■

130 W

■

256 MB of memory

■

The 128-MB version has reached end-of-life.

■

Unchannelized, concatenated OC12/STM4 for ATM

■

EFA ASIC

■

OC12/STM4

■

ATM/AAL5

■

See “OCx/STMx ATM Modules” on page 120 for information about the layer 2 and

■

layer 3 protocols and applications that this module combination supports.

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP module compatibility

Module redundancy support

OC12/STM4 ATM Multimode Without APS/MSP Redundancy Module Combination (256-MB Memory) ■ 73

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

1:N redundancy

■

NOTE: Line module redundancy is not supported on the ERX310 router.

■

ERX 11.1.x Module Guide

Cables and connectors

LEDs

Alarms, errors, and events

SC full duplex

■

Tx power:

■

min: –19 dBm

■

max: –14 dBm

■

Center wavelength: 1310 nm

■

Rx input power:

■

min: –30 dBm

■

max: –14 dBm

■

Rated for 2 km (1.2 miles) over 62.5-micron core cable with an optical loss of 0–9

■

dB or 50-micron core cable with an optical loss of 7 dB

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring SONET/SDH Interfaces in JUNOSe Physical Layer Configuration Guide,

■

Chapter 3, Configuring Unchannelized OCx/STMx Interfaces.

74 ■ OC12/STM4 ATM Multimode Without APS/MSP Redundancy Module Combination (256-MB Memory)

OC12/STM4 ATM Multimode With APS/MSP Redundancy Module Combination

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

OCx/STMx ATM or OCx/STMx /DS3-ATM

OC12 STM4 APS

MULTI MODE

1 active, 1 redundant

■

First supported: 2.0.0 (128 MB), 5.0.0 (256 MB)

■

Final supported: Not applicable

■

The OCx/STMx ATM line module or the OCx/STMx /DS3-ATM line module must have

■

a minimum of 256 MB of memory to be used with JUNOSe Release 5.3.0 or a higher-numbered release.

130 W

■

Can use either the 128-MB OCx/STMx ATM line module or the 256-MB OCx/STMx

■

/DS3-ATM line module.

Unchannelized, concatenated OC12/STM4 for ATM

■

EFA ASIC

■

OC12/STM4

■

ATM/AAL5

■

See “OCx/STMx ATM Modules” on page 120 for information about the layer 2 and

■

layer 3 protocols and applications that this module combination supports.

Model compatibility

SRP module compatibility

Module redundancy support

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

1:N redundancy

■

NOTE: Line module redundancy is not supported on the ERX310 router.

■

OC12/STM4 ATM Multimode With APS/MSP Redundancy Module Combination ■ 75

ERX 11.1.x Module Guide

Cables and connectors

LEDs

Alarms, errors, and events

SC full duplex

■

Tx power:

■

min: –19 dBm

■

max: –14 dBm

■

Center wavelength: 1310 nm

■

Rx input power:

■

min: –30 dBm

■

max: –14 dBm

■

Rated for 2 km (1.2 miles) over 62.5-micron core cable with an optical loss of 0–9

■

dB or 50-micron core cable with an optical loss of 7 dB

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring SONET/SDH Interfaces in JUNOSe Physical Layer Configuration Guide,

■

Chapter 3, Configuring Unchannelized OCx/STMx Interfaces.

76 ■ OC12/STM4 ATM Multimode With APS/MSP Redundancy Module Combination

OC12/STM4 ATM Single-Mode Intermediate Reach Without APS/MSP Redundancy Module Combination (256-MB Memory)

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

Model compatibility

OCx/STMx ATM or OCx/STMx /DS3-ATM

OC12 STM4 I/O

SINGLE MODE

1

■

First supported: 5.0.0, 5.3.0 or a higher-numbered release

■

Final supported: Not applicable

■

130 W

■

256 MB of memory

■

The 128-MB version has reached end-of-life.

■

Unchannelized, concatenated OC12/STM4 for ATM

■

EFA ASIC

■

OC12/STM4

■

ATM/AAL5

■

See “OCx/STMx ATM Modules” on page 120 for information about the layer 2 and

■

layer 3 protocols and applications that this module combination supports.

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP-5G+

SRP module compatibility

Module redundancy support

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

1:N redundancy

■

NOTE: Line module redundancy is not supported on the ERX310 router.

■

OC12/STM4 ATM Single-Mode Intermediate Reach Without APS/MSP Redundancy Module Combination (256-MB Memory) ■ 77

ERX 11.1.x Module Guide

Cables and connectors

LEDs

Alarms, errors, and events

SC full duplex

■

Tx power:

■

min: –15 dBm

■

max: –8 dBm

■

Center wavelength: 1310 nm

■

Rx input power:

■

min: –31 dBm

■

max: –8 dBm

■

Rated for 15 km (9.3 miles) of 9-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring SONET/SDH Interfaces in JUNOSe Physical Layer Configuration Guide,

■

Chapter 3, Configuring Unchannelized OCx/STMx Interfaces.

78 ■ OC12/STM4 ATM Single-Mode Intermediate Reach Without APS/MSP Redundancy Module Combination (256-MB Memory)

OC12/STM4 ATM Single-Mode Intermediate Reach With APS/MSP Redundancy Module Combination

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

OCx/STMx ATM or OCx/STMx /DS3-ATM

OC12 STM4 APS

SINGLE MODE

1 active, 1 redundant

■

First supported: 2.0.0 (128 MB), 5.0.0 (256 MB)

■

Final supported: Not applicable

■

The OCx/STMx ATM line module or the OCx/STMx/DS3-ATM line module must have

■

a minimum of 256 MB of memory to be used with JUNOSe Release 5.3.0 or a higher-numbered release.

130 W

■

Can use either the 128-MB OCx/STMx ATM line module or the 256-MB

■

OCx/STMx/DS3-ATM line module.

Unchannelized, concatenated OC12/STM4 for ATM

■

EFA ASIC

■

OC12/STM4

■

ATM/AAL5

■

See “OCx/STMx ATM Modules” on page 120 for information about the layer 2 and

■

layer 3 protocols and applications that this module combination supports.

Model compatibility

SRP module compatibility

Module redundancy support

OC12/STM4 ATM Single-Mode Intermediate Reach With APS/MSP Redundancy Module Combination ■ 79

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

1:N redundancy

■

NOTE: Line module redundancy is not supported on the ERX310 router.

■

ERX 11.1.x Module Guide

Cables and connectors

LEDs

Alarms, errors, and events

SC full duplex

■

Tx power:

■

min: –15 dBm

■

max: –8 dBm

■

Center wavelength: 1310 nm

■

Rx input power:

■

min: –31 dBm

■

max: –8 dBm

■

Rated for 15 km (9.3 miles) of 9-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring SONET/SDH Interfaces in JUNOSe Physical Layer Configuration Guide,

■

Chapter 3, Configuring Unchannelized OCx/STMx Interfaces.

80 ■ OC12/STM4 ATM Single-Mode Intermediate Reach With APS/MSP Redundancy Module Combination

OC12/STM4 ATM Single-Mode Long Reach Without APS/MSP Redundancy Module Combination (256-MB Memory)

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

Model compatibility

OCx/STMx ATM or OCx/STMx /DS3-ATM

OC12 STM4 I/O

LONG HAUL

1

■

First supported: 5.0.0, 5.3.0 or a higher-numbered release

■

Final supported: Not applicable

■

130 W

■

256 MB of memory

■

The 128-MB version has reached end-of-life.

■

Unchannelized, concatenated OC12/STM4 for ATM

■

EFA ASIC

■

OC12/STM4

■

ATM/AAL5

■

See “OCx/STMx ATM Modules” on page 120 for information about the layer 2 and

■

layer 3 protocols and applications that this module combination supports.

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP-5G+

SRP module compatibility

Module redundancy support

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

1:N redundancy

■

NOTE: Line module redundancy is not supported on the ERX310 router.

■

OC12/STM4 ATM Single-Mode Long Reach Without APS/MSP Redundancy Module Combination (256-MB Memory) ■ 81

ERX 11.1.x Module Guide

Cables and connectors

LEDs

Alarms, errors, and events

SC full duplex

■

Tx power:

■

min: –5.0 dBm

■

max: 0 dBm

■

Center wavelength: 1310 nm

■

Rx input power:

■

min: –34 dBm

■

max: –7 dBm

■

Fiber type: 9-micron core

■

Rated for 40 km (24.8 miles) of 9-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring SONET/SDH Interfaces in JUNOSe Physical Layer Configuration Guide,

■

Chapter 3, Configuring Unchannelized OCx/STMx Interfaces.

82 ■ OC12/STM4 ATM Single-Mode Long Reach Without APS/MSP Redundancy Module Combination (256-MB Memory)

OC12/STM4 ATM Single-Mode Long Reach With APS/MSP Redundancy Module Combination

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

OCx/STMx ATM or OCx/STMx /DS3-ATM

OC12 STM4 APS

LONG HAUL

1 active, 1 redundant

■

First supported: 2.0.0 (128 MB), 5.0.0 (256 MB)

■

Final supported: Not applicable

■

The OCx/STMx ATM line module or the OCx/STMx /DS3-ATM line module must have

■

a minimum of 256 MB of memory to be used with JUNOSe Release 5.3.0 or a higher-numbered release.

130 W

■

Can use either the 128-MB OCx/STMx ATM line module or the 256-MB OCx/STMx

■

/DS3-ATM line module.

Unchannelized, concatenated OC12/STM4 for ATM

■

EFA ASIC

■

OC12/STM4

■

ATM/AAL5

■

See “OCx/STMx ATM Modules” on page 120 for information about the layer 2 and

■

layer 3 protocols and applications that this module combination supports.

Model compatibility

SRP module compatibility

Module redundancy support

OC12/STM4 ATM Single-Mode Long Reach With APS/MSP Redundancy Module Combination ■ 83

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

1:N redundancy

■

NOTE: Line module redundancy is not supported on the ERX310 router.

■

ERX 11.1.x Module Guide

Cables and connectors

LEDs

Alarms, errors, and events

SC full duplex

■

Tx power:

■

min: –5.0 dBm

■

max: 0 dBm

■

Center wavelength: 1310 nm

■

Rx input power:

■

min: –34 dBm

■

max: –7 dBm

■

Fiber type: 9-micron core

■

Rated for 40 km (24.8 miles) of 9-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring SONET/SDH Interfaces in JUNOSe Physical Layer Configuration Guide,

■

Chapter 3, Configuring Unchannelized OCx/STMx Interfaces.

84 ■ OC12/STM4 ATM Single-Mode Long Reach With APS/MSP Redundancy Module Combination

OC12/STM4 POS Multimode Without APS/MSP Redundancy Module Combination

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

Model compatibility

OCx/STMx POS

OC12 STM4 I/O

MULTI MODE

1

■

First supported: 2.0.0

■

Final supported: Not applicable

■

120 W

■

Unchannelized, concatenated OC12/STM4 for POS

■

EFA ASIC

■

OC12/STM4

■

HDLC framing

■

See “OCx/STMx POS and OC48 Modules” on page 123 for information about the

■

layer 2 and layer 3 protocols and applications that this module combination supports.

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP module compatibility

Module redundancy support

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

1:N redundancy

■

NOTE: Line module redundancy is not supported on the ERX310 router.

■

OC12/STM4 POS Multimode Without APS/MSP Redundancy Module Combination ■ 85

ERX 11.1.x Module Guide

Cables and connectors

LEDs

Alarms, errors, and events

SC full duplex

■

Tx power:

■

min: –19 dBm

■

max: –14 dBm

■

Center wavelength: 1310 nm

■

Rx input power:

■

min: –30 dBm

■

max: –14 dBm

■

Rated for 2 km (1.2 miles) over 62.5-micron core cable with an optical loss of

■

0–9 dB or 50-micron core cable with an optical loss of 7 dB

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring SONET/SDH Interfaces in JUNOSe Physical Layer Configuration Guide,

■

Chapter 3, Configuring Unchannelized OCx/STMx Interfaces.

86 ■ OC12/STM4 POS Multimode Without APS/MSP Redundancy Module Combination

OC12/STM4 POS Multimode With APS/MSP Redundancy Module Combination

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

Model compatibility

OCx/STMx POS

OC12 STM4 APS

MULTI MODE

1 active, 1 redundant

■

First supported: 2.0.0

■

Final supported: Not applicable

■

120 W

■

Unchannelized, concatenated OC12/STM4 for POS

■

EFA ASIC

■

OC12/STM4

■

HDLC framing

■

See “OCx/STMx POS and OC48 Modules” on page 123 for information about the

■

layer 2 and layer 3 protocols and applications that this module combination supports.

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP module compatibility

Module redundancy support

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

1:N redundancy

■

NOTE: Line module redundancy is not supported on the ERX310 router.

■

OC12/STM4 POS Multimode With APS/MSP Redundancy Module Combination ■ 87

ERX 11.1.x Module Guide

Cables and connectors

LEDs

Alarms, errors, and events

SC full duplex

■

Tx power:

■

min: –19 dBm

■

max: –14 dBm

■

Center wavelength: 1310 nm

■

Rx input power:

■

min: –30 dBm

■

max: –14 dBm

■

Rated for 2 km (1.2 miles) over 62.5-micron core cable with an optical loss of 0–9

■

dB or 50-micron core cable with an optical loss of 7 dB

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring SONET/SDH Interfaces in JUNOSe Physical Layer Configuration Guide,

■

Chapter 3, Configuring Unchannelized OCx/STMx Interfaces.

88 ■ OC12/STM4 POS Multimode With APS/MSP Redundancy Module Combination

OC12/STM4 POS Single-Mode Intermediate Reach Without APS/MSP Redundancy Module Combination

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

Model compatibility

OCx/STMx POS

OC12 STM4 I/O

SINGLE MODE

1

■

First supported: 2.0.0

■

Final supported: Not applicable

■

120 W

■

Unchannelized, concatenated OC12/STM4 for POS

■

EFA ASIC

■

OC12/STM4

■

HDLC framing

■

See “OCx/STMx POS and OC48 Modules” on page 123 for information about the

■

layer 2 and layer 3 protocols and applications that this module combination supports.

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP module compatibility

Module redundancy support

Cables and connectors

OC12/STM4 POS Single-Mode Intermediate Reach Without APS/MSP Redundancy Module Combination ■ 89

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

1:N redundancy

■

NOTE: Line module redundancy is not supported on the ERX310 router.

■

SC full duplex

■

Tx power:

■

min: –15 dBm

■

max: –8 dBm

■

Center wavelength: 1310 nm

■

Rx input power:

■

min: –31 dBm

■

max: –8 dBm

■

Rated for 15 km (9.3 miles) of 9-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

ERX 11.1.x Module Guide

LEDs

Alarms, errors, and events

See “Module LEDs” on page 133.

■

See Monitoring SONET/SDH Interfaces in JUNOSe Physical Layer Configuration

■

Guide, Chapter 3, Configuring Unchannelized OCx/STMx Interfaces.

90 ■ OC12/STM4 POS Single-Mode Intermediate Reach Without APS/MSP Redundancy Module Combination

OC12/STM4 POS Single-Mode Intermediate Reach With APS/MSP Redundancy Module Combination

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

Model compatibility

OCx/STMx POS

OC12 STM4 APS

SINGLE MODE

1 active, 1 redundant

■

First supported: 2.0.0

■

Final supported: Not applicable

■

120 W

■

Unchannelized, concatenated OC12/STM4 for POS

■

EFA ASIC

■

OC12/STM4

■

HDLC framing

■

See “OCx/STMx POS and OC48 Modules” on page 123 for information about the

■

layer 2 and layer 3 protocols and applications that this module combination supports.

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP module compatibility

Module redundancy support

Cables and connectors

OC12/STM4 POS Single-Mode Intermediate Reach With APS/MSP Redundancy Module Combination ■ 91

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

1:N redundancy

■

NOTE: Line module redundancy is not supported on the ERX310 router.

■

SC full duplex

■

Tx power:

■

min: –15 dBm

■

max: –8 dBm

■

Center wavelength: 1310 nm

■

Rx input power:

■

min: –31 dBm

■

max: –8 dBm

■

Rated for 15 km (9.3 miles) of 9-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

ERX 11.1.x Module Guide

LEDs

Alarms, errors, and events

See “Module LEDs” on page 133.

■

See Monitoring SONET/SDH Interfaces in JUNOSe Physical Layer Configuration

■

Guide, Chapter 3, Configuring Unchannelized OCx/STMx Interfaces.

92 ■ OC12/STM4 POS Single-Mode Intermediate Reach With APS/MSP Redundancy Module Combination

OC12/STM4 POS Single-Mode Long Reach Without APS/MSP Redundancy Module Combination

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

Model compatibility

OCx/STMx POS

OC12 STM4 I/O

LONG HAUL

1

■

First supported: 2.0.0

■

Final supported: Not applicable

■

120 W

■

Unchannelized, concatenated OC12/STM4 for POS

■

EFA ASIC

■

OC12/STM4

■

HDLC framing

■

See “OCx/STMx POS and OC48 Modules” on page 123 for information about the

■

layer 2 and layer 3 protocols and applications that this module combination supports.

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP module compatibility

Module redundancy support

Cables and connectors

OC12/STM4 POS Single-Mode Long Reach Without APS/MSP Redundancy Module Combination ■ 93

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

1:N redundancy

■

NOTE: Line module redundancy is not supported on the ERX310 router.

■

SC full duplex

■

Tx power:

■

min: –5.0 dBm

■

max: 0 dBm

■

Center wavelength: 1310 nm

■

Rx input power:

■

min: –34 dBm

■

max: –7 dBm

■

Rated for 40 km (24.8 miles) of 9-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

ERX 11.1.x Module Guide

LEDs

Alarms, errors, and events

See “Module LEDs” on page 133.

■

See Monitoring SONET/SDH Interfaces in JUNOSe Physical Layer Configuration

■

Guide, Chapter 3, Configuring Unchannelized OCx/STMx Interfaces.

94 ■ OC12/STM4 POS Single-Mode Long Reach Without APS/MSP Redundancy Module Combination

OC12/STM4 POS Single-Mode Long Reach With APS/MSP Redundancy Module Combination

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

Model compatibility

OCx/STMx POS

OC12 STM4 APS

LONG HAUL

1 active, 1 redundant

■

First supported: 2.0.0

■

Final supported: Not applicable

■

120 W

■

Unchannelized, concatenated OC12/STM4 for POS

■

EFA ASIC

■

OC12/STM4

■

HDLC framing

■

See “OCx/STMx POS and OC48 Modules” on page 123 for information about the

■

layer 2 and layer 3 protocols and applications that this module combination supports.

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP module compatibility

Module redundancy support

Cables and connectors

OC12/STM4 POS Single-Mode Long Reach With APS/MSP Redundancy Module Combination ■ 95

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

1:N redundancy

■

NOTE: Line module redundancy is not supported on the ERX310 router.

■

SC full duplex

■

Tx power:

■

min: –5.0 dBm

■

max: 0 dBm

■

Center wavelength: 1310 nm

■

Rx input power:

■

min: –34 dBm

■

max: –7 dBm

■

Rated for 40 km (24.8 miles) of 9-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

ERX 11.1.x Module Guide

LEDs

Alarms, errors, and events

See “Module LEDs” on page 133.

■

See Monitoring SONET/SDH Interfaces in JUNOSe Physical Layer Configuration

■

Guide, Chapter 3, Configuring Unchannelized OCx/STMx Interfaces.

96 ■ OC12/STM4 POS Single-Mode Long Reach With APS/MSP Redundancy Module Combination

OC48/STM16 POS Single-Mode Short Reach Module Combination

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

Model compatibility

SRP module compatibility

OC48

OC48 FRAME APS

1

■

First supported: 4.1.x

■

Final supported: Not applicable

■

120 W

■

Unchannelized, concatenated OC48/STM16 for POS

■

FFA ASIC

■

OC48/STM16

■

HDLC framing

■

See “OCx/STMx POS and OC48 Modules” on page 123 for information about

■

the layer 2 and layer 3 protocols and applications that this module combination supports.

ERX1440 router

■

SRP-40G

■

SRP-40G PLUS

■

Module redundancy support

Cables and connectors

LEDs

Alarms, errors, and events

Not applicable

■

LC full duplex connector

■

Transmit power:

■

min: –10 dBm

■

max: –3 dBm

■

Center wavelength: 1310 nm

■

Receive input power:

■

min: –18 dBm

■

max: –3 dBm

■

Rated for 2 km (1.2 miles) of 9-micron core cable

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring SONET/SDH Interfaces in JUNOSe Physical Layer Configuration

■

Guide, Chapter 3, Configuring Unchannelized OCx/STMx Interfaces.

OC48/STM16 POS Single-Mode Short Reach Module Combination ■ 97

ERX 11.1.x Module Guide

Service Module (SM) Module Combination

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

Model compatibility

SERVICE MODULE

No I/O module

Not applicable

■

First supported: 5.1.0

■

Final supported: Not applicable

■

130 W

■

Tunnel Service for IP tunnels, L2F tunnels, and LNS termination

■

EFA ASIC

■

IP tunnels

■

LNS termination

■

Network Address Translation

■

Stateful firewall

■

See “Service Modules” on page 125 for information about the layer 2 and layer

■

3 protocols and applications that this module combination supports.

ERX7xx models

■

ERX14xx models

■

ERX310 router

■

SRP module compatibility

Module redundancy support

Cables and connectors

LEDs

Alarms, errors, and events

SRP-5G+

■

SRP-10G

■

SRP-40G

■

SRP-40G PLUS

■

SRP-SE10G

■

Multiple SMs provide redundancy.

■

See JUNOSe Physical Layer Configuration Guide, Chapter 6, Managing

■

Tunnel-Service and IPSec-Service Interfaces

Not applicable

■

See “Module LEDs” on page 133.

■

See Monitoring Tunnel-Service Interfaces in JUNOSe Physical Layer Configuration

■

Guide, Chapter 6, Managing Tunnel-Service and IPSec-Service Interfaces.

98 ■ Service Module (SM) Module Combination

SRP-5G+ Module Combination (1-GB Memory)

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

Model compatibility

SRP-5G+

SRP I/O

7

■

First supported: 4.1.3 or later 4.1.x release, 5.0.4 or later 5.0.x release, 5.1.2

■

or higher-numbered release, 5.2.0

Final supported: Not applicable

■

125 W

■

Switch route processor (5 Gbps)

■

Has a minimum of 1 GB of error checking and correction (ECC) memory with

■

a 1-GB nonvolatile storage (NVS) card.

The 512–MB version has reached end-of-life.

■

Not applicable

■

Ethernet (IEEE 802.3)

■

10/100Base-T

■

RS-232

■

Not applicable

■

ERX705 Broadband Services Router

■

SRP module compatibility

Module redundancy support

Cables and connectors

LEDs

Alarms, errors, and events

SRP-5G+

■

1:1 redundancy

■

Terminal blocks

■

BNC, 75–ohm

■

Wire wrap posts

■

RJ-45

■

RS-232 (DB-9)

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

■

See “Module LEDs” on page 133.

■

See Monitoring Modules in JUNOSe System Basics Configuration Guide, Chapter 6,

■

Managing Modules.

SRP-5G+ Module Combination (1-GB Memory) ■ 99

ERX 11.1.x Module Guide

SRP-5G+ Module Combination (2-GB Memory)

Line module label

I/O module label

Number of I/O ports

Software release

Description

Type

Capability

Software features

Model compatibility

SRP-5G+

SRP I/O

7

■

First supported: 4.1.3 or later 4.1.x release, 5.0.4 or later 5.0.x release, 5.1.2

■

or higher-numbered release, 5.2.0

Final supported: Not applicable

■

125 W

■

Switch route processor (5 Gbps)

■

Has a minimum of 2 GB of error checking and correction (ECC) memory

■

with a 1-GB nonvolatile storage (NVS) card.

The 512–MB version has reached end-of-life.

■

Not applicable

■

Ethernet (IEEE 802.3)

■

10/100Base-T

■

RS-232

■

Not applicable

■

ERX705 router

■

SRP module compatibility

Module redundancy support

Cables and connectors

LEDs

Alarms, errors, and events

SRP-5G+

■

1:1 redundancy

■

Terminal blocks

■

BNC, 75–ohm

■

Wire wrap posts

■

RJ-45

■

RS-232 (DB-9)

■

See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more

■

information.

See “Module LEDs” on page 133.

■

See Monitoring Modules in JUNOSe System Basics Configuration Guide,

■

Chapter 6, Managing Modules.

100 ■ SRP-5G+ Module Combination (2-GB Memory)