Juniper E SERIES BROADBAND SERVICES ROUTERS - E SERIES END-OF-LIFE MODULE GUIDE 6-10-2010, ERX310, E120, E320, ERX14 Series User Manual
...
E Series™ Broadband
Services Routers
E Series™ End-of-Life Module Guide
Published: 2010-10-06
Copyright © 2010, Juniper Networks, Inc.
E Series End-of-Life Module Guide
This guide provides an overview and description of E Series modules that are end-of-life
(EOL) and can no longer be ordered for the following routers:
•
•
•
•
•
Depending on the EOL schedule of a module, new software releases might not support
the module.
Table 1 on page 3 lists EOL modules alphabetically. It lists EOL modules for ERX routers
first and then for E120 and E320 routers.
ERX7xx models
ERX14xx models
ERX310 router
E120 router
E320 router
NOTE: Any future JunosE release number provided in the Actual or Predicted
Last JunosE Support field of Table 1 on page 3 is based on the current JunosE
release schedule. If the release schedule changes in the future, Juniper
Networks will update the associated Product Support Notification (PSN)
Technical Bulletin for any affected EOL modules.
For more information about E Series routers and modules, refer to the following guides:
•
ERX module installation and maintenance—ERX Hardware Guide
•
E120 and E320 module installation and maintenance—E120 and E320 Hardware Guide
•
Managing E Series routers—JunosE System Basics Configuration Guide
•
Configuring E Series modules—JunosE Link Layer Configuration Guide
To obtain the most current list of EOL modules, see the End-of-Life Products page on
the Juniper Networks Web site at http://www.juniper.net/support/eol.
Copyright © 2010, Juniper Networks, Inc.2
Table 1: End-of-Life Modules
Line Module
LabelCombination Name
ERX ROUTER MODULES
CE1
Channelized OC3/STM1
cOCx/STMxF0cOC3/STM1 multimode
I/O Module
Label
I/O
MULTIMODE
First
JunosE
Support
Actual or
Predicted
Last
JunosE
Support
Page
87.3.x1.1.0CE1 FULL I/OCE1CE1
915.0.x2.2.0cOC3 STM1 F0
intermediate reach
long reach
Channelized OC12/STM4
without APS/MSP
redundancy
single-mode
intermediate reach
without APS/MSP
redundancy
single-mode
intermediate reach with
APS/MSP redundancy
cOCx/STMxF0cOC3/STM1single-mode
I/O
SINGLE MODE
cOCx/STMxF0cOC3/STM1single-mode
I/O
LONG HAUL
cOCx/STMxF0cOC12/STM4multimode
I/O
MULTI MODE
cOCx/STMxF0cOC12/STM4
I/O
SINGLE MODE
cOCx/STMxF0cOC12/STM4
COC12 F0 APS
SINGLE MODE
7.0.2,
7.2.0
1115.0.x2.2.0cOC3 STM1 F0
1315.0.x2.2.0cOC3 STM1 F0
1515.0.x2.2.0cOC12 STM4 F0
1715.0.x2.2.0cOC12 STM4 F0
1915.0.x6.1.3,
single-mode long reach
Channelized T1
Channelized T3
cOCx/STMxF0cOC12/STM4
LONG HAUL
2115.0.x2.2.0cOC12 STM4
237.3.x1.1.0CT1 FULL I/OCT1CT1
3Copyright © 2010, Juniper Networks, Inc.
E Series End-of-Life Module Guide
Table 1: End-of-Life Modules (continued)
Line Module
LabelCombination Name
E3
I/O Module
Label
First
JunosE
Support
Actual or
Predicted
Last
JunosE
Support
Page
247.0.x1.0.0CT3/T3 I/OCT3CT3 (3 ports)
2514.0.x3.2.0CT3/T3 12 I/OCT3/T3-F0CT3/T3 12 (12 ports)
267.1.x1.1.0E3 I/OE3 ATME3 ATM
277.0.x1.1.0E3 I/OE3 FRAMEE3 Frame (3 ports)
Fast Ethernet
Only line module is EOL.
Gigabit Ethernet (1–port)
(128 MB)
Only line module is EOL.
(128 MB)
Only line module is EOL.
(128 MB)
Only line module is EOL.
COCX-F3E3 Frame (12 ports)
FRAME I/O
2814.0.x4.0.2E3-12
297.0.x1.3.0FE-2 I/OFE-2FE-2 (2 ports)
305.2.x2.0.0FE-8 I/OGE/FEFE-8 (8 ports) (128 MB)
315.2.x2.0.0GE I/O SFPGE/FEGE 1000Base-LH
335.2.x2.0.0GE I/O SFPGE/FEGE 1000Base-SX
355.2.x2.0.0GE I/O SFPGE/FEGE 1000Base-ZX
HSSI
IPSec Service
IPSec Service
OC3/STM1
377.3.x3.1.0HSSI-3 I/OHSSI-3FHSSI
3814.0.x4.0.2No I/O moduleIPSEC
SERVICE
Copyright © 2010, Juniper Networks, Inc.4
Table 1: End-of-Life Modules (continued)
Line Module
LabelCombination Name
I/O Module
Label
First
JunosE
Support
Actual or
Predicted
Last
JunosE
Support
Page
multimode
single-mode
OC3/STM1 ATM
OC3/STM1 ATM
multimode without
APS/MSP redundancy
(128 MB)
Only line module is EOL.
OC3/STM1 ATM
single-mode
intermediate reach
without APS/MSP
redundancy (128 MB)
Only line module is EOL.
OC3/STM1 ATM
single-mode long reach
without APS/MSP
redundancy (128 MB)
OC3OC3 (dual-port)
OC3OC3 (dual-port)
OCx/STMx
ATM or
OCx/STMx
/DS3-ATM
OCx/STMx
ATM or
OCx/STMx
/DS3-ATM
OCx/STMx
ATM or
OCx/STMx
/DS3-ATM
394.1.x1.0.0OC3 I/O
MULTI MODE
404.1.x1.0.0OC3 I/O
SINGLE MODE
415.2.x2.0.0OC3-4 I/O
MULTI MODE
435.2.x2.0.0OC3-4 I/O
SINGLE MODE
455.2.x2.0.0OC3-4 I/O
LONG HAUL
Only line module is EOL.
OC12/STM4 ATM
OC12/STM4 ATM
multimode without
APS/MSP redundancy
(128 MB)
Only line module is EOL.
OC12/STM4 ATM
single-mode
intermediate reach
without APS/MSP
redundancy (128 MB)
Only line module is EOL.
OCx/STMx
ATM or
OCx/STMx
/DS3-ATM
OCx/STMx
ATM or
OCx/STMx
/DS3-ATM
475.2.x2.0.0OC12 STM4 I/O
MULTI MODE
495.2.x2.0.0OC12 STM4 I/O
SINGLE MODE
5Copyright © 2010, Juniper Networks, Inc.
E Series End-of-Life Module Guide
Table 1: End-of-Life Modules (continued)
Line Module
LabelCombination Name
I/O Module
Label
First
JunosE
Support
Actual or
Predicted
Last
JunosE
Support
Page
OC12/STM4 ATM
single-mode long reach
without APS/MSP
redundancy (128 MB)
Only line module is EOL.
SRPs
memory)
OCx/STMx
ATM or
OCx/STMx
/DS3-ATM
LONG HAUL
SRP I/OSRP-5G+SRP-5G+ (2-GB
SRP I/OSRP-10GSRP-10G(1-GB memory)
515.2.x2.0.0OC12 STM4 I/O
535.2.x1.0.0SRP I/OSRP-5GSRP-5G (512 MB)
548.0.x3.0.2SRP I/OSRP-5G+SRP-5G+ (512 MB)
5514.0.x4.1.3,
5.0.4,
5.1.2,
5.2.0
565.2.x1.1.0SRP I/OSRP-10GSRP-10G (512 MB)
578.0.x4.1.3,
5.0.4,
5.1.2,
5.2.0
587.1.x5.1.0SRP-SE I/OSRP-SE10GSRP-SE10G (512 MB)
SRP-40G PLUS (1 GB)
PLUS
T3
T3 ATM (4 ports)
(128 MB)
Only line module is EOL.
ATM or
OCx/STMx
/DS3-ATM
Tunnel Service Module (TSM)
595.2.x3.4.1SRP I/OSRP-40GSRP-40G (512 MB)
607.1.x4.0.0SRP I/OSRP-40G
617.0.x1.1.0CT3/T3 I/OT3 ATMT3 ATM (3 ports)
625.2.x4.1.04xDS3 ATM I/OOCx/STMx
637.0.x1.1.0CT3/T3 I/OT3 FRAMET3 Frame (3 ports)
6414.0.x4.0.2CT3/T3 12 I/OCOCX-F3T3 Frame (12 ports)
Copyright © 2010, Juniper Networks, Inc.6
Table 1: End-of-Life Modules (continued)
Line Module
LabelCombination Name
I/O Module
Label
First
JunosE
Support
Actual or
Predicted
Last
JunosE
Support
Page
TSM
SERVICE
X.21/V.35
E120 and E320 ROUTER MODULES
Gigabit Ethernet IOA
10GE IOA
ES2-S1
10GE
IOA
X.21/V.35 I/OX.21/V.35X.21/V.35
10GE
IOA
658.0.x3.0.2No I/O moduleTUNNEL
667.3.x2.10.1,
3.3.2
6814.0.x7.0.1ES2-S1
7Copyright © 2010, Juniper Networks, Inc.
E Series End-of-Life Module Guide
CE1 Module Combination
Line module label
I/O module label
Number of I/O ports
Software release
Description
Type
Capability
Software features
Model compatibility
SRP module compatibility
CE1
CE1 FULL I/O
•
20
•
First supported: 1.1.0
•
Final supported: 7.3.x
•
40 W
•
Channelized E1
•
Non-ASIC
•
E1
•
HDLC framing
•
See ERX Module Guide, Appendix A, Module Protocol Support for information
about the layer 2 and layer 3 protocols and applications that this module
combination supports.
•
ERX7xx models
•
ERX1410 router
•
SRP-5G
•
SRP-5G+
•
SRP-10G
Module redundancy support
Cables and connectors
LEDs
Alarms, errors, and events
•
1:N redundancy
•
RJ-48C,120 ohm
•
BNC, 75-ohm via a balun panel that connects to the I/O module
•
Use shielded cables to maintain EMC compliance.
•
The transmitted signal complies with ITUT G.703, Physical/electrical
characteristics of hierarchical digital interfaces (November 2001) for cable
lengths up to 450 m (492 yards).
•
See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.
•
See ERX Module Guide, Appendix B, Module LEDs.
•
See Monitoring Interfaces in the Configuring Channelized T1 and Channelized E1
Interfaces chapter of the JunosE Physical Layer Configuration Guide for Release
8.0.x and earlier.
Copyright © 2010, Juniper Networks, Inc.8
cOC3/STM1 Multimode Module Combination
cOC3/STM1 Multimode Module Combination
Line module label
I/O module label
Number of I/O ports
Software release
Description
Type
Capability
Software features
cOCx/STMx F0
cOC3 STM1 F0 I/O
MULTI MODE
•
4
•
First supported: 2.2.0
•
Final supported: 15.0.x
•
130 W
•
OC3/STM1 channelized to DS3, DS1, E1, and DS0
•
Supports either E1 or T1 operation, but not E1 and T1 operation simultaneously
•
EFA ASIC
•
OC3/STM1
•
DS3
•
T1, E1
•
DS0
•
HDLC framing
•
See ERX Module Guide, Appendix A, Module Protocol Support for information about
the layer 2 and layer 3 protocols and applications that this module combination
supports.
Model compatibility
SRP module compatibility
Module redundancy support
•
ERX7xx models
•
ERX14xx models
•
ERX310 router
•
SRP-5G+
•
SRP-10G
•
SRP-40G
•
SRP-40G PLUS
•
SRP-SE10G
•
1:N redundancy
•
NOTE: Line module redundancy is not supported on the ERX310 router.
9Copyright © 2010, Juniper Networks, Inc.
E Series End-of-Life Module Guide
Cables and connectors
LEDs
Alarms, errors, and events
•
Up to four SC full duplex connectors
•
Tx power:
•
min: –19 dBm
•
max: –14 dBm
•
Center wavelength: 1310 nm
•
Rx input power:
•
min: –30 dBm
•
max: –14 dBm
•
Rated for 2 km (1.2 miles) over 62.5-micron core cable with an optical loss of
0–9 dB or 50-micron core cable with an optical loss of 7 dB
•
See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.
•
See ERX Module Guide, Appendix B, Module LEDs.
•
See Monitoring Interfaces in JunosE Physical Layer Configuration Guide, Chapter 4,
Configuring Channelized OCx/STMx Interfaces.
Copyright © 2010, Juniper Networks, Inc.10
cOC3/STM1 Single-Mode Intermediate Reach Module Combination
cOC3/STM1 Single-Mode Intermediate Reach Module Combination
Line module label
I/O module label
Number of I/O ports
Software release
Description
Type
Capability
Software features
cOCx/STMx F0
cOC3 STM1 F0 I/O
SINGLE MODE
•
4
•
First supported: 2.2.0
•
Final supported: 15.0.x
•
130 W
•
OC3/STM1 channelized to DS3, DS1, E1, and DS0
•
EFA ASIC
•
OC3/STM1
•
DS3, DS1
•
T1, E1
•
DS0
•
HDLC framing
•
See ERX Module Guide, Appendix A, Module Protocol Support for information
about the layer 2 and layer 3 protocols and applications that this module
combination supports.
Model compatibility
SRP module compatibility
Module redundancy support
•
ERX7xx models
•
ERX14xx models
•
ERX310 router
•
SRP-5G+
•
SRP-10G
•
SRP-40G
•
SRP-40G PLUS
•
SRP-SE10G
•
1:N redundancy
•
NOTE: Line module redundancy is not supported on the ERX310 router.
11Copyright © 2010, Juniper Networks, Inc.
E Series End-of-Life Module Guide
Cables and connectors
LEDs
Alarms, errors, and events
•
Up to four SC full duplex connectors
•
Tx power:
•
min: –15 dBm
•
max: –8 dBm
•
Center wavelength: 1310 nm
•
Rx input power:
•
min: –31 dBm
•
max: –8 dBm
•
Rated for 15 km (9.3 miles) of 9-micron core cable
•
See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.
•
See ERX Module Guide, Appendix B, Module LEDs.
•
See Monitoring Interfaces in JunosE Physical Layer ConfigurationGuide, Chapter 4,
Configuring Channelized OCx/STMx Interfaces.
Copyright © 2010, Juniper Networks, Inc.12
cOC3/STM1 Single-Mode Long Reach Module Combination
cOC3/STM1 Single-Mode Long Reach Module Combination
Line module label
I/O module label
Number of I/O ports
Software release
Description
Type
Capability
Software features
cOCx/STMx F0
cOC3 STM1 F0 I/O
LONG HAUL
•
4
•
First supported: 2.2.0
•
Final supported: 15.0.x
•
130 W
•
OC3/STM1 channelized to DS3, DS1, E1, and DS0
•
EFA ASIC
•
OC3/STM1
•
DS3, DS1
•
T1, E1
•
DS0
•
HDLC framing
•
See ERX Module Guide, Appendix A, Module Protocol Support for information
about the layer 2 and layer 3 protocols and applications that this module
combination supports.
Model compatibility
SRP module compatibility
Module redundancy support
•
ERX7xx models
•
ERX14xx models
•
ERX310 router
•
SRP-5G+
•
SRP-10G
•
SRP-40G
•
SRP-40G PLUS
•
SRP-SE10G
•
1:N redundancy
•
NOTE: Line module redundancy is not supported on the ERX310 router.
13Copyright © 2010, Juniper Networks, Inc.
E Series End-of-Life Module Guide
Cables and connectors
LEDs
Alarms, errors, and events
•
Up to four SC full duplex connectors
•
Tx power:
•
min: –5.0 dBm
•
max: 0 dBm
•
Center wavelength: 1310 nm
•
Rx input power:
•
min: –34 dBm
•
max: –7 dBm
•
Fiber type: 9-micron core
•
Rated for 40 km (24.8 miles) of 9-micron core cable
•
See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.
•
See ERX Module Guide, Appendix B, Module LEDs.
•
See Monitoring Interfaces in JunosE Physical Layer Configuration Guide, Chapter 4,
Configuring Channelized OCx/STMx Interfaces.
Copyright © 2010, Juniper Networks, Inc.14
cOC12/STM4 Multimode Without APS/MSP Redundancy Module Combination
cOC12/STM4 Multimode Without APS/MSP Redundancy Module Combination
Line module label
I/O module label
Number of I/O ports
Software release
Description
Type
Capability
Software features
cOCx/STMx F0
cOC12 STM4 F0 I/O
MULTI MODE
•
1
•
First supported: 2.2.0
•
Final supported: 15.0.x
•
130 W
•
OC12/STM4 channelized to DS3, DS1, E1, and DS0
•
EFA ASIC
•
OC12/STM4
•
OC3/STM1
•
DS3, DS1
•
T1, E1
•
DS0
•
HDLC framing
•
See ERX Module Guide, Appendix A, Module ProtocolSupport for information about
the layer 2 and layer 3 protocols and applications that this module combination
supports.
Model compatibility
SRP module compatibility
Module redundancy support
•
ERX7xx models
•
ERX14xx models
•
ERX310 router
•
SRP-5G+
•
SRP-10G
•
SRP-40G
•
SRP-40G PLUS
•
SRP-SE10G
•
1:N redundancy
•
NOTE: Line module redundancy is not supported on the ERX310 router.
15Copyright © 2010, Juniper Networks, Inc.
E Series End-of-Life Module Guide
Cables and connectors
LEDs
Alarms, errors, and events
•
SC full duplex connector
•
Tx power:
•
min: –19 dBm
•
max: –14 dBm
•
Center wavelength: 1310 nm
•
Rx input power:
•
min: –30 dBm
•
max: –14 dBm
•
Rated for 2 km (1.2 miles) over 62.5-micron core cable with an optical loss of 0–9
dB or 50-micron core cable with an optical loss of 7 dB
•
See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.
•
See ERX Module Guide, Appendix B, Module LEDs.
•
See Monitoring Interfaces in JunosE Physical Layer Configuration Guide, Chapter 4,
Configuring Channelized OCx/STMx Interfaces.
Copyright © 2010, Juniper Networks, Inc.16
cOC12/STM4 Single-Mode Intermediate Reach Without APS/MSP Redundancy Module Combination
cOC12/STM4Single-Mode IntermediateReach WithoutAPS/MSP Redundancy Module
Combination
Line module label
I/O module label
Number of I/O ports
Software release
Description
Type
Capability
Software features
cOCx/STMx F0
cOC12 STM4 F0 I/O
SINGLE MODE
•
1
•
First supported: 2.2.0
•
Final supported: Not applicable
•
130 W
•
OC12/STM4 channelized to DS3, DS1, E1, and DS0
•
EFA ASIC
•
OC12/STM4
•
OC3/STM1
•
DS3, DS1
•
T1, E1
•
DS0
•
HDLC framing
•
See ERX Module Guide, Appendix A, Module Protocol Support for information
about the layer 2 and layer 3 protocols and applications that this module
combination supports.
Model compatibility
SRP module compatibility
Module redundancy support
•
ERX7xx models
•
ERX14xx models
•
ERX310 router
•
SRP-5G+
•
SRP-10G
•
SRP-40G
•
SRP-40G PLUS
•
SRP-SE10G
•
1:N redundancy
•
NOTE: Line module redundancy is not supported on the ERX310 router.
17Copyright © 2010, Juniper Networks, Inc.
E Series End-of-Life Module Guide
Cables and connectors
LEDs
Alarms, errors, and events
•
SC full duplex connector
•
Tx power:
•
min: –15 dBm
•
max: –8 dBm
•
Center wavelength: 1310 nm
•
Rx input power:
•
min: –31 dBm
•
max: –8 dBm
•
Rated for 15 km (9.3 miles) of 9-micron core cable
•
See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.
•
See ERX Module Guide, Appendix B, Module LEDs.
•
See Monitoring Interfaces in JunosE Physical Layer Configuration Guide, Chapter 4,
Configuring Channelized OCx/STMx Interfaces.
Copyright © 2010, Juniper Networks, Inc.18
cOC12/STM4 Single-Mode Intermediate Reach With APS/MSP Redundancy Module Combination
cOC12/STM4 Single-Mode Intermediate Reach With APS/MSP Redundancy Module
Combination
Line module label
I/O module label
Number of I/O ports
Software release
Description
Type
Capability
cOCx/STMx F0
COC12 F0 APS
SINGLE MODE
•
2
•
1 active, 1 redundant
•
First supported: 6.1.3 or later 6.1.x release, 7.0.2 or later 7.0.x release, 7.2.0 and
higher-numbered release
•
Final supported: 15.0.x
•
130 W
•
OC12/STM4 channelized to DS3, DS1, E1, and DS0
•
EFA ASIC
•
OC12/STM4
•
OC3/STM1
•
DS3, DS1
•
T1, E1
•
DS0
•
HDLC framing
Software features
Model compatibility
SRP module compatibility
Module redundancy support
•
See ERX Module Guide, Appendix A, Module ProtocolSupport for information about
the layer 2 and layer 3 protocols and applications that this module combination
supports.
•
ERX7xx models
•
ERX14xx models
•
ERX310 router
•
SRP-5G+
•
SRP-10G
•
SRP-40G
•
SRP-40G PLUS
•
SRP-SE10G
•
1:N redundancy
•
NOTE: Line module redundancy is not supported on the ERX310 router.
19Copyright © 2010, Juniper Networks, Inc.
E Series End-of-Life Module Guide
Cables and connectors
LEDs
Alarms, errors, and events
•
SC full duplex connector
•
Tx power:
•
min: –15 dBm
•
max: –8 dBm
•
Center wavelength: 1310 nm
•
Rx input power:
•
min: –31 dBm
•
max: –7 dBm
•
Rated for 15 km (9.3 miles) of 9-micron core cable
•
See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.
•
See ERX Module Guide, Appendix B, Module LEDs.
•
See Monitoring Interfaces in JunosE Physical Layer Configuration Guide, Chapter 4,
Configuring Channelized OCx/STMx Interfaces.
Copyright © 2010, Juniper Networks, Inc.20
cOC12/STM4 Single-Mode Long Reach Module Combination
cOC12/STM4 Single-Mode Long Reach Module Combination
Line module label
I/O module label
Number of I/O ports
Software release
Description
Type
Capability
Software features
cOCx/STMx F0
cOC12 STM4
LONG HAUL
•
1 active, 1 redundant
•
First supported: 2.2.0
•
Final supported: 15.0.x
•
130 W
•
OC12/STM4 channelized to DS3, DS1, E1, and DS0
•
EFA ASIC
•
OC12/STM4
•
OC3/STM1
•
DS3, DS1
•
T1, E1
•
DS0
•
HDLC framing
•
See ERX Module Guide, Appendix A, Module Protocol Support for information
about the layer 2 and layer 3 protocols and applications that this module
combination supports.
Model compatibility
SRP module compatibility
Module redundancy support
•
ERX7xx models
•
ERX14xx models
•
ERX310 router
•
SRP-5G+
•
SRP-10G
•
SRP-40G
•
SRP-40G PLUS
•
SRP-SE10G
•
1:N redundancy
•
NOTE: Line module redundancy is not supported on the ERX310 router.
21Copyright © 2010, Juniper Networks, Inc.
E Series End-of-Life Module Guide
Cables and connectors
LEDs
Alarms, errors, and events
•
SC full duplex connector
•
Tx power:
•
min: –5.0 dBm
•
max: 0 dBm
•
Center wavelength: 1310 nm
•
Rx input power:
•
min: –34 dBm
•
max: –7 dBm
•
Fiber type: 9-micron core
•
Rated for 40 km (24.8 miles) of 9-micron core cable
•
See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.
•
See ERX Module Guide, Appendix B, Module LEDs.
•
See Monitoring Interfaces in JunosE Physical Layer Configuration Guide, Chapter 4,
Configuring Channelized OCx/STMx Interfaces.
Copyright © 2010, Juniper Networks, Inc.22
Loading...