Universal push-button module
Universal push-button module, 1-gang
Art. No. : 4191 TSM
Universal push-button module, 2-gang
Art. No. : 4192 TSM
Universal push-button module, 3-gang
Art. No. : 4193 TSM
Universal push-button module, 4-gang
Art. No. : 4194 TSM
Operating instructions
1 Safety instructions
Electrical equipment may only be installed and fitted by electrically skilled persons.
Failure to observe the instructions may cause damage to the device and result in fire and
other hazards.
Use only the enclosed plastic screws for fastening to the supporting frame! Otherwise
safe operation cannot be ensured. Electrostatic discharges can cause defects in the
device.
These instructions are an integral part of the product, and must remain with the end
customer.
2 Function
System information
This device is a product of the KNX system and complies with the KNX directives. Detailed
technical knowledge obtained in KNX training courses is a prerequisite to proper understanding.
The function of this device depends upon the software. Detailed information on loadable
software and attainable functionality as well as the software itself can be obtained from the
manufacturer´s product database. Planning, installation and commissioning of the device are
carried out with the aid of KNX-certified software. The latest versions of product database and
the technical descriptions are available on our website.
Intended use
- Operation of loads, e.g. light on/off, dimming, blinds up/down, brightness values,
temperatures, calling up and saving light scenes, etc.
- Installation in appliance box according to DIN 49073
Product characteristics
- The pushbutton functions switching, dimming, controlling blinds, value transmitter, calling
up moods, etc.
- Measurement of the room temperature
- Completion with keyset
- Two red status LEDs for each button
- A blue operation LED as an orientation light and to indicate the programming status
- Integrated bus coupling unit
- One, two or three functions per button
- Push-button function or rockers function, vertical or horizontal
- Connection of push-button extension module to expand the universal push-button sensor
module to include four additional buttons
3 Operation
Operating a function or load
Depending on the programming, a button can have up to three functions assigned to it –
upper/left, lower/right, entire surface. Operation depends on the specific function.
o Switch: Short press on button.
o Dim: Long press on button. The dimming process ends when the button is released.
o Move Venetian blind: Long press on button.
32566733
j0082566733
1/5
23.03.2016
Universal push-button module
o Stop or adjust Venetian blind: Short press on button.
o Call up light scene: Short press on button.
o Save light scene: Long press on button.
o Set value, e.g. brightness or temperature setpoint: Short press on button.
4 Information for electrically skilled persons
4.1 Fitting and electrical connection
DANGER!
Electrical shock on contact with live parts in the installation environment.
Electrical shocks can be fatal.
Before working on the device, disconnect the power supply and cover up live
parts in the working environment.
Snapping on the adapter frame
o With the adapter frame (3) in the correct orientation, snap it from the front onto the
pushbutton module (4) (figure 1). Note marking TOP.
Fitting and connecting the device
Figure 1: Mounting the push-button module
(1) Supporting frame
(2) Design frame
(3) Adapter frame
(4) Push-button module
(5) Fastening screws
(6) Buttons
(7) KNX connection terminal
(8) Box screws
Supporting frame side A for A design ranges, CD design ranges and FD design. Supporting
frame side B for LS design ranges.
When the push-button expansion module is used (figure 2): Preferably mounted vertically. Use
large supporting frame (14). When mounting on only one flush-mounted box, countersink the
lower screws into the wall, e.g. with a ø 6 x10 mm hole. Use supporting frame as template.
32566733
j0082566733
2/5
23.03.2016
Universal push-button module
DANGER!
When mounting with 230 V devices under a common cover, e.g. socket outlets,
there is a danger of electrical shocks in the event of a fault!
Electrical shocks can be fatal.
Do not install any 230 V devices in combination with a push-button extension
module under a common cover!
o Mount supporting frame (1) or (14) in the correct orientation on an appliance box. Note
marking TOP; marking A or B in front. Use only the enclosed box screws (8).
o Push frame (2) onto supporting frame.
o Mount push-button sensor expansion module (15) preferably below. Route connecting
cable (16) between supporting frame and intermediate web.
o Push-button expansion module: Insert connecting cable (16) in the correct orientation into
slot (17) in the push-button module. Do not crimp the connecting cable (figure 1).
o Connect push-button module (4) to the KNX using KNX connecting terminal (7) and push
onto the supporting frame.
o Fasten pushbutton module(s) to supporting frame using the enclosed plastic screws (5).
Tighten the plastic screws only lightly.
o Before mounting the buttons (6), load the physical address into the device (see chapter
4.2. Commissioning).
Figure 2: Mounting with push-button expansion module
4.2 Commissioning
Loading the physical address and application software
Configuration and commissioning with ETS3.0d Patch A or more recent.
The device is connected and ready for operation.
The buttons are not mounted yet.
i If the device does not receive any application software, or the wrong application software,
then the blue operation LED flashes slowly.
32566733
j0082566733
3/5
23.03.2016
Universal push-button module
Figure 3: Activating programming mode
o Activate programming mode: Press and hold push-button at the upper left (9). Then press
push-button at the lower right (10, 11 or 12):
Push-button module Prog. push-button
– 4gang, 3gang (9) + (10)
– 2gang (9) + (11)
– 1gang (9) + (12)
The operation LED (13) flashes quickly.
o Load physical address into the device.
The operation LED (13) returns to its previous state – off, on, or flashing slowly.
o Write the physical address on the device label.
o Load the application software into the device.
Installing the buttons
The buttons are available as a complete set of buttons. Individual buttons or the complete set of
buttons can be replaced using buttons with symbols.
i The mounting spider is not required to mount the buttons.
The physical address is loaded into the device.
o Place the buttons on the device in the correct orientation and snap in with a short push.
Note marking TOP.
32566733
j0082566733
4/5
23.03.2016
Universal push-button module
Figure 4: Button assignment
5 Appendix
5.1 Technical data
KNX medium TP
Commissioning mode S-mode
Rated voltage KNX DC 21 ... 32VSELV
Power consumption KNX typ. 150mW
Connection mode KNX device connection terminal
Measuring range -5 ... +45°C
Protection class III
Ambient temperature -5 ... +45°C
Storage/transport temperature -25 ... +70°C
5.2 Accessories
Cover kit 1-gang Art. No. ..401 TSA..
Cover kit 2-gang Art. No. ..402 TSA..
Cover kit 3-gang Art. No. ..403 TSA..
Cover kit 4-gang Art. No. ..404 TSA..
Push-button extension module, 1-gang Art. No. 4091 TSEM
Push-button extension module, 2-gang Art. No. 4092 TSEM
Push-button extension module, 3-gang Art. No. 4093 TSEM
Push-button extension module, 4gang Art. No. 4094 TSEM
5.3 Warranty
The warranty follows about the specialty store in between the legal framework as provided for
by law.
ALBRECHT JUNG GMBH & CO. KG
Volmestraße 1
58579 Schalksmühle
GERMANY
Telefon: +49 2355 806-0
Telefax: +49 2355 806-204
kundencenter@jung.de
www.jung.de
32566733
j0082566733
5/5
23.03.2016
Loading...