Page 1
Flush-mounted room climate interface with satellite input
Flush-mounted room climate interface with satellite input
Art.-No.: 2531 UP
Operationsmanual
1 Safety instructions
Electrical equipment may only be installed and fitted by qualified electricians.
Failure to observe the instructions may cause damage to the device and result in fire and
other hazards.
The device is not suitable for disconnection from supply voltage.
The connected actuators are not electrically isolated from the mains – even when
switched off.
Do not connect any external voltage to the inputs, since doing so may damage the
device(s), and the SELV potential on the KNX bus line will no longer be available.
For parallel connection of several drives to an output it is indispensable to observe the
corresponding instructions of the manufacturers, and to use a cutoff relay if necessary.
There is otherwise risk of irreparable damage to the drives.
Use only Venetian blind drives with mechanical or electronic limit switches. Check the
limit switches for correct adjustment. Observe the specifications of the motor
manufacturers.
These instructions are an integral part of the product, and must remain with the end
customer.
2 Device components
picture 1
(1) Control cable
(2) Programming button and LED
(3) Connection of mains and power cables
Connection assignment, power cables
BK, black: connection L
BN, brown: connection of Venetian blind, up
PK, pink: connection of Venetian blind, down
GY, grey: actuator connection
1/7
82573403
J:0082573403
15.05.2009
Page 2
picture 2
Connection assignment of control cable
RD, red: KNX+
BK, black: KNX–
GN, green: input 1
YE, yellow: input 2
WH, white: input 3
BN, brown: COM inputs 1...3
3 Function
System information
This device is a product of the KNX system and complies with the KNX directives. Detailed
technical knowledge obtained in KNX training courses is a prerequisite to proper
understanding.
The function of this device depends upon the software. Detailed information on loadable
software and attainable functionality as well as the software itself can be obtained from the
manufacturer´s product database.
Planning, installation and commissioning of the device are carried out with the aid of KNXcertified software. Full functionality with KNX commissioning software version ETS3.0d
onwards.
An updated version of the product database, technical descriptions and conversion programs
and other auxiliary programs are available on our Internet website.
Intended purpose
- Switching of electrically-driven Venetian blinds, awnings and similar blinds for AC 230 V
mains voltage.
- Switching of electrothermal actuators
- Installation in appliance box to DIN 49073
- Connection with enclosed terminals
Product characteristics
- Control of Venetian blinds, awnings and similar blinds
- Control of electrothermal actuators
- Three binary inputs for potential-free contacts, usable as extension inputs for local
operation
- Supply via bus, no additional power supply necessary
Venetian blind function
- Blind position directly controllable
- Slat position directly controllable
- Feedback of movement status, blind position and slat position
- Forced position through higher-level controller
- Safety function: 3 independent wind alarms, rain alarm, frost alarm
- Sun protection function
Actuator function
- Switching operation or PWM operation
- Actuators with characteristics opened or closed without power
2/7
82573403
J:0082573403
15.05.2009
Flush-mounted room climate interface with satellite input
Page 3
- Overload-protected, short circuit-protected
- Protection against jamming valves
- Forced position
- Cyclical monitoring of the input signals configurable.
i PWM operation: electrothermal actuators only have the positions Open and Closed. In
PWM operation, switch-on and switch-off during the drive's cycle time achieves an almost
constant behaviour.
4 Information for qualified electricians
4.1 Fitting and electrical connection
DANGER!
Electrical shock when live parts are touched.
Electrical shocks can be fatal.
Before working on the device, disconnect the power supply and cover up live
parts in the working environment.
Connecting and mounting the device
DANGER!
When connecting the bus/extensions and mains' voltage wires in a shared
appliance box, the KNX bus cable may come into contact with the mains
voltage.
The endangers the safety of the entire KNX installation. People at remote
devices may also receive an electric shock.
Do not place bus/extensions and mains voltage terminals in a shared
connection compartment. Use an appliance box with a fixed partition wall
(picture 3) or separate boxes.
picture 3
(4) Appliance box
(5) Partition
(6) Potential-free contacts, e.g. for window contact or installation pushbuttons
3/7
82573403
J:0082573403
15.05.2009
Flush-mounted room climate interface with satellite input
Page 4
picture 4
Minimum spacing between the mains voltage and bus/extension wires: 4 mm (picture 4).
o Connect the load (picture 5). Use terminals.
o Connect the device to KNX.
o If necessary, connect potential-free contacts (6) to inputs (picture 2).
o Install the device in the appliance box.
picture 5
i In the as-delivered state, Inputs 1 and 2 operate the Venetian blind output. Input 3 has no
function.
Function of Inputs 1 and 2 in the as-delivered state
Input NO contact Blind
1 Press briefly Adjust slats Up / Stop
1 Press for a long time Move up
2 Press briefly Adjust slats Down / Stop
2 Press for a long time Move down
4/7
82573403
J:0082573403
15.05.2009
Flush-mounted room climate interface with satellite input
Page 5
Use terminals
picture 6: Stripping length
o Strip 9 - 11 mm of the cable (picture 6).
picture 7: Connection of the fine-wire cable
o Push the terminal together on the side with the square opening and connect a fine-wire
cable (picture 7).
5/7
82573403
J:0082573403
15.05.2009
Flush-mounted room climate interface with satellite input
Page 6
picture 8: Connection of the single-stranded cable
o Push the single-stranded cable into the round opening on the installation side up to the
stop (picture 8).
4.2 Commissioning
Load the address and the application software
o Switch on the bus voltage
o Assign physical addresses and load application software into the device.
o Note the physical address on the device label.
5 Appendix
5.1 Technical data
Supply
Rated voltage AC 230 / 240 V ~
Mains frequency 50 / 60 Hz
Switching voltage AC 250 V~
Ambient conditions
Ambient temperature -5 ... +45 °C
Storage/transport temperature -25 ... +70 °C
Venetian blind output
Contact type µ
Switching current AC1 3 A
Minimum switching current AC 100 mA
Motors 230 V 600 VA
Heating output
Output type Semi-conductor (Triac), ε
Switching current 5 ... 25 mA
Switch-on current max. 600 mA (2 s)
Number of drives per output max. 2
Control cable and inputs
Control cable (preterminated) YY6x0.6
Input type Potential-free
Total length of extension unit cable max. 5 m
Poll voltage, extension inputs approx. 5 V
Dimension Ø×H 53×28 mm
Connection type Terminal (enclosed)
Single-stranded 1.0 ... 2.5 mm²
6/7
82573403
J:0082573403
15.05.2009
Flush-mounted room climate interface with satellite input
Page 7
KNX
KNX medium TP 1
Commissioning mode S mode
Rated voltage KNX DC 21 V ... 32 V SELV
Power consumption KNX max. 240 mW
Connection mode KNX Connection terminal on control cable
5.2 Warranty
We reserve the right to make technical and formal changes to the product in the interest of
technical progress.
We provide a warranty as provided for by law.
Please send the unit postage-free with a description of the defect to our central customer
service office:
ALBRECHT JUNG GMBH & CO. KG
Service Center
Kupferstr. 17-19
D-44532 Lünen
Service-Line: +49 (0) 23 55 . 80 65 51
Telefax: +49 (0) 23 55 . 80 61 89
mail.vka@jung.de
General equipment
Service-Line: +49 (0) 23 55 . 80 65 55
Telefax: +49 (0) 23 55 . 80 62 55
mail.vkm@jung.de
KNX equipment
Service-Line: +49 (0) 23 55 . 80 65 56
Telefax: +49 (0) 23 55 . 80 62 55
mail.vkm@jung.de
The Πsymbol is a free trade symbol, which is solely intended for the authorities and does not
guarantee any properties.
ALBRECHT JUNG GMBH & CO. KG
Volmestraße 1
D-58579 Schalksmühle
Telefon: +49.23 55.8 06-0
Telefax: +49.23 55.8 06-1 89
E-mail: mail.info@jung.de
Internet: www.jung.de
www.jung-katalog.de
7/7
82573403
J:0082573403
15.05.2009
Flush-mounted room climate interface with satellite input
Loading...