Jung JKB 1, JKB 3, JKB 4 Operating Manual
OPERATING MANUAL
Please read before starting work
REVOLVING TRANSPORT TROLLEY JKB
JKB 1 JKB 3 JKB 4
Type JKB 1 JKB 3 JKB 4
Load capacity kg/ lbs
Number of castors each
Castor dimension x L
Height mm/ inch
Supporting surface
of load pad
Trolley dimension L x W mm/ inch
Weight kg/ lbs
mm/ inch
mm/ inch
1 000 / 2 200 3 000 / 6 600 4 000 / 8 800
3 8 12
75 x 60 / 3 x 2.4“ 85 x 40 / 3.3 x 1.6“ 85 x 40 / 3.3 x 1.6“
110 / 4.3“ 110 / 4.3“ 110 / 4.3“
215 / 8.5“ 250 / 9.8“ 250 / 9.8“
390 x 340 / 15.4 x 13.4” 575 x 460 / 22.6 x 18.1” 690 x 640 / 27.2 x 25.2”
10 / 22 32 / 71 51 / 112
RECOMMENDED USE CONTENTS
Transport trolleys:
are specially designed for transport of heavy loads on solid level floors in
factories. Do not exceed the maximum load capacity recommended by
this operating manual.
are extremely manoeuvrable. Never use trolleys on uneven or declining
floors - this can lead to danger due to the potential of run-away loads.
Must not be used:
- for transport on public streets and places
for transport of people or animals
in extreme environments (e.g. under hazardous, explosive, flammable or
corrosive conditions)
Use only as directed. The manufacturer or supplier is not liable
for any damage resulting from improper use of the trolleys.
Accidents resulting from improper use are the responsibility of
the user.
The user should read these operating and service instructions carefully
before using the trolleys. In particular, attention should be paid to the
Safety Instructions on page 3
Technical Data, application…………………………………………… 1
General information, operating instructions.................................... 2
Safety instructions, Spare parts..................................................... 3
Declaration of conformity.............................................................. 4
OPERATING MANUAL
Revolving
Transport
Trolleys
J
KB
For safer lifting of loads we recommend
hydraulic
jacksby
JUNG.
LOADING
Lift up rear end
of load and place two trolle
ys underneath.
°
UNLOADING
(
Reverse
the
loading
steps
)
Lift up the front end of the load and remove first the
centre
placed cassette.
Ensure
that the ground intended for transport is clean and free of any loose
Revolving transport trolleys do
not have any in
-
built braking
Please read first before starting work
The weight of the loads may not exceed the load capacity of the
transport trolleys. If centre of gravity is outside the centre of load please
ensure that load weight does not exceed the load capacity of each
trolley cassette.
Each trolley should be fixed to the load when moving a load over an
uneven floor.
Please follow the sequences described below when loading / unloading.
If necessary lift up step by step alternately front and rear end.
Use squared timber to secure the load between the steps to avoid
big angle of the machine surface until you reach the height of the
cassettes.
Connect two side-by-side cassettes with a connecting rod for
affixed support on uneven surfaces.
Adjust connecting rod and clamp it if necessary!
Place the load slowly and carefully on the cassettes.
Attention! Load may tilt
Remove jacks.
Lift up front end of load and place one or two trolleys underneath.
When using three trolleys distribute the load cassettes in such a
way that the weight is evenly divided across all cassettes.
Attention! Take the load’s centre of gravity into consideration!
Place the load slowly and carefully on the cassettes.
Remove jacks.
0,5
Lower the front end of the load slowly and carefully to the ground or to a
suitable base. Lift up rear end of the load and remove connected cassettes.
Lower the rear end of the load slowly and carefully to the ground or to a
suitable base.
Lower the load step by step to the floor.
TRANSPORT
objects. Move the load by pushing manually or using a suitable towing vehicle.
Ensure that the cassettes are always securely positioned whilst moving.
system:
Never exceed 1 mph when moving!
Do not move on a slope of more than 0.5 degree.
Only use suitable towing vehicles.
Make sure that the load does not exceed the permissible towing
weight.
Always use the connection bar delivered with the rear cassettes.
This ensures that the cassettes run parallel under the weight as long
as the surface is hard, even and clean.
On surfaces that are not perfectly smooth, level and clean ensure that
all trolleys are affixed to the load in a suitable manner.
Loading...