Jung FMx5001M Series, FMx5002M Series, FMx5003M Series, FMx5004M Series Operating Instructions Manual

eNet radio transmitter module

eNet radio transmitter module 1-gang

Art. No. : FM..5001M

eNet radio transmitter module 2-gang

Art. No. : FM..5002M

eNet radio transmitter module 3-gang

Art. No. : FM..5003M

eNet radio transmitter module 4-gang

Art. No. : FM..5004M

Operating instructions

1 Safety instructions

Electrical devices may only be mounted and connected by electrically skilled
persons.

Serious injuries, fire or property damage possible. Please read and follow manual fully.

Keep button cells out of reach of children! If button cells are swallowed, get medical help
immediately.

Risk of explosion! Do not throw batteries into fire.

Risk of explosion! Do not recharge batteries.

The radio communication takes place via a non-exclusively available transmission path,
and is therefore not suitable for safety-related applications, such as emergency stop and
emergency call.

These instructions are an integral part of the product, and must remain with the end
customer.

2 Device components

Figure 1: 4-gang radio wall transmitter module

(1) Base plate
(2) Fastening screws for the base plate
(3) Design frame
(4) Wall transmitter module
(5) Cover
(6) Fastening screws for the wall transmitter module

1/10

32595513
J0082595513

22.03.2017

(7) Cover kit
(14) Battery holder

3 Function

Intended use

- Radio sensor for transmission of switching, dimming, blind movement and scene
commands

- Operation with radio actuators from the eNet system

Product characteristics

- Display of the actuator status for status poll by a green status LED per channel

- Display of the transmission status by a red transmission LED

- Switch-on brightness of dimmer actuators can be saved.

- Battery-powered device

- Signalling of transmission errors can be switched off

Can be set with eNet server:

- Master dimming function

- Scene All On

- Operation locks

i If settings are changed with the eNet server, operation and signalling could vary from what

is described here.

i The parameter list is in the Internet in the documentation for this device.

Supplementary function with eNet server

- Update of the device software

4 Operation

i When operating with the eNet Server, operation and signalling could vary from what is

described here.

Function of LED in operation

As soon as a button is pressed or released, the transmission LED (9) signals radio
transmission.

- LED lights up for 2 seconds

Then, the status LED (8) signals the actuator status/group status

- LED lights up for 3 seconds:
At least one actuator is switched on, or one Venetian blind is not in the top end position

- LED remains off:
All the actuators are switched off or the blinds are all in the upper end position

i If there is no status message from an actuator, the transmission LED (9) signals a

transmission error. The transmission LED flashes quickly for 5 seconds.

2/10

32595513
J0082595513

22.03.2017

eNet radio transmitter module

Channel assignment of the wall transmitter

Figure 2: Channel assignment of wall transmitter module 1-gang, 2-gang, 3-gang and 4-gang

(8) Status LED, green (one per channel)
(9) Transmission LED, red (one per device)

Operating light

o Switching: Press button for less than 0.4 seconds.
o Dimming: Press the button for longer than 0.4 seconds. The dimming process ends when

the button is released.

o Switching on dimmer actuators at minimum brightness: Press the right button for longer

than 0.4 seconds.

o Switching on dimmer actuators at minimum brightness and dimming to maximum

brightness: Press the left button for longer than 0.4 seconds.

Operating blind

o Moving the Venetian blind: Press the button for longer than 1 second.
o Stopping the Venetian blind or adjusting the slats: Press the button for less than 1 second.

Operating push-button actuator

o Press the left or right button of a channel: The load is switched on for the duration of the

button-press.

i The maximum actuation length is 60 seconds.

Recalling scenes

o Press the scene button briefly.

Actuators switching to the saved scene.

Changing scene

o Press the scene button briefly.

Actuators switching to the saved scene.

o Setting a new scene.
o Press scene button for longer than 4 seconds.

Actuators first switching to the old scene and save the new scene after 4 seconds.

3/10

32595513
J0082595513

22.03.2017

eNet radio transmitter module