Page 1
eNet radio blinds actuator 1-gang mini
eNet radio blinds actuator 1-gang mini
Art. No. : FMJ50700UP
Operating instructions
1 Safety instructions
Electrical devices may only be mounted and connected by electrically skilled
persons.
Serious injuries, fire or property damage possible. Please read and follow manual fully.
Danger of electric shock. Always disconnect before carrying out work on the devise or
load. In so doing, take all the circuit breakers into account, which support dangerous
voltages to the device and or load.
For parallel connection of several motors to an output it is essential to observe the
corresponding instructions of the manufacturers, and to use a cut-off relay if necessary.
The motors may be destroyed.
Risk of injury. Use the device only for controlling Venetian blind and roller shutter
motors or awnings. Do not use it to switch other loads.
Use only venetian blind motors with mechanical or electronic limit switches. Check the
limit switches for correct adjustment. Observe the specifications of the motor
manufacturers. Device can be damaged.
These instructions are an integral part of the product, and must remain with the end
customer.
2 Device components
Figure 1: Front view
(1) Operating mode switch
(2) Button Prog
(3) Status LED
(4) Measuring points for voltage measurement, terminals rear-mounted
3 Function
Intended use
- Controlling electrically driven Venetian blinds, rolling shutters and awnings
82581443
J0082581443
1/11
24.03.2017
Page 2
eNet radio blinds actuator 1-gang mini
- Operation with suitable eNet radio transmitters
- Mounting in appliance box according to DIN 49073 with a suitable cover
- Installation in surface-mounted housing or panel-mounted housing (accessories) for
suspended ceilings
Product characteristics
- Operating mode switch for switch-over to blind actuator, shutter actuator or
parameterisation via eNet server
- Positioning of the blind/shutter via scene request
- Positions for sun protection and twilight can be saved
- Status feedback to radio transmitter
- Switchable output with Prog button
- Blind/shutter running time can be saved
- Slat change-over time can be saved
- Fabric-stretching for awnings
- Status indicator via LED
Can be set with eNet server:
- Change-over-time for direction change
- Running direction invertible
- Operation locks
- Position for sun protection, twilight, lock-out protection and wind alarm
i When operating with the eNet Server, operation and signalling could vary from what is
described here.
Supplementary functions with eNet Server:
- Fully encrypted radio transmission (AES-CCM) from eNet Server software version 2.0
- Update of the device software
- Repeater function
- Reading of error memory
Behaviour after mains voltage return
The response after mains voltage return can be configured with the eNet server. Default setting:
no action.
4 Operation
Operation is with radio transmitters, please observe the radio transmitter instructions.
5 Information for electrically skilled persons
5.1 Fitting and electrical connection
DANGER!
Electrical shock when live parts are touched.
Electrical shocks can be fatal.
Before carrying out work on the device or load, disengage all the
corresponding circuit breakers. Cover up live parts in the working environment.
Mounting and connecting actuator
To ensure good transmission quality, keep a sufficient distance from any possible sources of
interference, e.g. metallic surfaces, microwave ovens, hi-fi and TV systems, ballasts or
transformers.
82581443
J0082581443
2/11
24.03.2017
Page 3
eNet radio blinds actuator 1-gang mini
Figure 2: Connection example
o Connect load as shown in the connection example (figure 2).
o Insert the actuator in the appliance box in such a way that the Prog button and status LED
are visible.
Figure 3: Operating mode switch
Switch position Function
PC Operating mode and parameter set with eNet
server.*)
Ht Commissioning - determine running time
It Commissioning - determine slat time
O Blind operating mode
P Operating mode rolling shutter, awning
*) If the operating mode switch is turned from the position PC to another operating mode, the
parameters are set to the default setting. The settings made with the eNet Server will be
lost.
o Set the operating mode switch.
o Switch on mains voltage.
i The load can be switched by briefly pressing the Prog button.
Status LED lights up: output switched on
Status LED off: output switched off
o Perform commissioning.
82581443
J0082581443
3/11
24.03.2017
Page 4
eNet radio blinds actuator 1-gang mini
i In installation positions that are not easily accessible, turn the operating mode switch to
position PC after commissioning and performing a function test. Subsequent changes to
the device settings can thus be carried out with the aid of the eNet Server without involving
excessive installation work.
o Mount the cover.
5.2 Commissioning
DANGER!
Electrical shock when live parts are touched.
Electrical shocks can be fatal.
During commissioning, cover the parts carrying voltage on radio transmitters
and actuators and in their surrounding area.
i The actuator can also be commissioned with eNet Server as an alternative to the
commissioning described here.
i Prerequisite for scenes and positioning movements is that the moving times of the
connected blind/shutter in the actuator are saved.
Saving blind/shutter running time for rolling shutters
The operating mode switch (figure 3) is in the Venetian blind O or rolling shutter P position.
o Turn the operating mode switch (1) to the I t position until the blind/shutter reaches the
upper end position.
o Turn operating mode switch to the Ht position.
The blind/shutter moves downwards.
o When the lower end position is reached, turn the operating mode switch to the P position.
The running time is saved and the blind/shutter moves to the upper end position.
Saving blind/shutter running time for blind
The operating mode switch (figure 3) is in the Venetian blind O or rolling shutter P position.
o Turn the operating mode switch (1) to the I t position until the blind/shutter reaches the
upper end position.
o Turn operating mode switch to the Ht position.
The blind/shutter moves downwards.
o When the lower end position is reached, turn the operating mode switch to the I t
position.
o When the slats have been fully changed over, turn the operating mode switch to the O
position.
The running times are saved and the blind/shutter moves to the upper end position.
Saving the awning running time
The operating mode switch (figure 3) is in the Venetian blind O or rolling shutter P position.
o Turn the operating mode switch (1) to the I t position until the blind/shutter reaches the
upper end position.
o Turn operating mode switch to the Ht position.
o For awnings without fabric-stretching function: When the extended lower end position is
reached, turn the operating mode switch to the It position. As soon the fabric is hanging
taut, turn the operating mode switch to the P position.
o For awnings with their own fabric-stretching function: When the extended lower end
position is reached, turn the operating mode switch to the P position.
The running times are saved and the blind/shutter moves to the upper end position.
Connecting actuator to radio transmitters
Load is switched off.
o Press the Prog button for longer than 4 seconds.
82581443
J0082581443
4/11
24.03.2017
Page 5
eNet radio blinds actuator 1-gang mini
The blind/shutter starts.
The status LED flashes after 4 seconds and the blind/shutter stops. The actuator is in
programming mode for approx. 1 minute.
o Switch radio transmitter to programming mode (see radio transmitter instructions).
o Trigger telegram on the radio transmitter.
The status LED lights up for 5 seconds.
The actuator is connected to the radio transmitter. The actuator and radio transmitter exit
the programming mode automatically.
i If the status LED of the actuator flashes 3 times at 1-second intervals for approx. 5
seconds, then the programming operation was not successful. All the memory locations in
the actuator or radio transmitter are occupied.
i Scene buttons must be connected separately.
Disconnecting connection to a radio transmitter
o Carry out the same steps as when connecting (see Connecting actuator to radio
transmitters).
The status LED of the actuator flashes quickly for 5 seconds.
The actuator is disconnected from the radio transmitter. The actuator and radio transmitter
exit the programming mode automatically.
i If there several connections or scene buttons for a radio transmitter, all connections must
be disconnected individually.
Resetting the device to the factory setting
All connections to radio transmitters are disconnected and parameters are reset to default
setting. If the operating mode switch is on PC, the rolling shutter operating mode is set.
i The connections in the radio transmitters are preserved and must be deleted separately.
Load is switched off.
o Press the Prog button for at least 20 seconds.
The blind/shutter starts.
The status LED flashes after 4 seconds and the blind/shutter stops. The status LED flashes
faster after 20 seconds.
o Release Prog button and press briefly once again within 10 seconds.
The status LED flashes more slowly for approx. 5 seconds.
The device is reset to default setting.
6 Appendix
6.1 Technical data
Rated voltage AC 230V~
Mains frequency 50 / 60Hz
Ambient temperature -25 ... +70°C
Minimum actuation time in operating mode
Venetian blind 0.1s
Roller shutter 0.3s
Minimum switching current AC 100mA
Contact type µ
Standby power max. 0.5W
Running time 1 ... 600s
Running time default setting 120 sec
Slat adjusting time 0 ... 10s
Connected load
Motors 1000W
Connection
single stranded 0.75 ... 4mm²
Finely stranded with conductor sleeve 0.75 ... 2.5mm²
82581443
J0082581443
5/11
24.03.2017
Page 6
eNet radio blinds actuator 1-gang mini
Dimensions Ø×H 53×28 mm
Radio frequency 868.0 ... 868.6MHz
Transmission capacity max. 20mW
Transmitting range in free field typ. 100m
Receiver category 2
6.2 Parameter list
The device parameters can be changed with the eNet server:
Device and channels
Parameters Setting options, Basic
setting
Function Venetian blind, unused, basic
position: Venetian blind
Operating mode Roller shutter
Venetian blind
Awning
Basic setting: Roller shutter
Explanations
Venetian blind
The channel is integrated for
the "Venetian blind" central
function in the eNet SMART
HOME app.
Unused
The channel is not displayed
in the eNet SMART HOME
app and is disabled for use in
the commissioning interface.
Roller shutter
A rolling shutter or an awning
is controlled for which the
Fabric stretching function is
required.
Venetian blind
A Venetian blind is controlled.
Awning
An awning is controlled for
which the Fabric stretching
function is required.
Advanced device settings
Parameters Setting options, Basic
setting
Manual commissioning On, Off
Basic setting: On
Repeater mode On, Off
Basic setting: Off
Channel settings
Parameters Setting options, Basic
setting
82581443
J0082581443
6/11
Explanations
Disables manual
commissioning for all device
channels. In the "Off" setting,
the device cannot be reset to
the factory setting.
In addition to its other
functions, the device can be
used as a repeater. In the
"On" setting, the device
repeats all the received
telegrams.
Explanations
24.03.2017
Page 7
eNet radio blinds actuator 1-gang mini
Operating hours up 0...65535
Basic setting: Current value
Operating hours down 0...65535
Basic setting: Current value
Extended channel settings
Parameters Setting options, Basic
setting
The time is counted during
which the load is physically
switched on (relay contact
closed).
This parameter can be reset to
"0", for example after
exchanging the load.
The Reset button is used to
reset the meter to "0". The
device must be programmed
to apply the change.
The time is counted during
which the load is physically
switched on (relay contact
closed).
This parameter can be reset to
"0", for example after
exchanging the load.
The Reset button is used to
reset the meter to "0". The
device must be programmed
to apply the change.
Explanations
Operating mode Roller shutter
Venetian blind
Awning
Basic setting: Roller shutter
Manual commissioning On, Off
Basic setting: On
Local Operation On, Off
Basic setting: On
Running time 1 ... 600 sec
Basic setting: 120 s
Slat change-over time
Fabric-stretching time
0 ms ... 10 sec
300 ms … 10 s
Basic setting: 0 ms / 300 ms
Minimum change-over-time 300 ms ... 10 sec
Basic setting: 1 s
See Device and channels.
Blocks manual commissioning
for the device channel. In the
"Off" setting, the device
cannot be reset to the factory
setting.
Blocks the output for operation
using the button.
Absolute time which the
blind/shutter requires from the
top to the bottom end position.
The entry is essential if scene
or position movements are to
occur.
Absolute time for changingover Venetian blind slats. The
fabric stretching time can also
be set here for the Awning
operating mode.
Minimum interruption time
when changing directions.
Increasing the minimum
change-over time will cause
less wear on the motors.
82581443
J0082581443
7/11
24.03.2017
Page 8
eNet radio blinds actuator 1-gang mini
Invert movement direction On, Off
Basic setting: Off
Behaviour on voltage return No change
Configured value
Basic setting: No change
Configured venetian blind
position
0 ... 100 %
Basic setting: 0 %
Configured slat position 0 ... 100 %
Basic setting: 0 %
Behaviour after the end of the
disabling function
no change
Last value
Down
up
Basic setting: No change
Inverts the activation of the
relay outputs. During inverted
operation, the relay outputs
"Up" and "Down" should be
activated in reverse. This is
required, for example, for
controlling skylights.
Defines the behaviour of the
output after voltage return.
RMD design: Bus voltage
return
If the value "Configured
position" is entered for the
parameter "Behaviour after
voltage return", then the
blind/shutter position set here
is approached.
If the value "Configured
position" is entered for the
parameter "Behaviour after
voltage return", then the slat
position set here is
approached.
Behaviour of the output when
a block is removed.
Manual saving of the scene
values
On, Off
Basic setting: On
Priority, lock-out protection 0...4
Basic setting: 1
Activate lock-out protection
blind position
Activate lock-out protection
slat position
Deactivate lock-out protection
blind position
Deacitvate lock-out protection
slat position
0 ... 100 %
Basic setting: 0 %
0 ... 100 %
Basic setting: 0 %
0 ... 100 %
Basic setting: 0 %
0 ... 100 %
Basic setting: 0 %
Disables the saving of the
current Venetian blind position
as scene value in an actuator
for a command via a
transmitter.
Specifies the priority for
recalling and removing a
scene of type Lock-out
protection for the channel.
Defines the behaviour of the
output on activating the lockout protection.
Defines the slat position of the
output on activating the lockout protection. Only visible
when the Venetian blind
operating mode is set.
Defines the behaviour of the
output on deactivating the
lock-out protection. Only
visible when the priority for the
lock-out protection is 0.
Defines the behaviour of the
output on deactivating the
lock-out protection. Only
visible when the priority for
lock-out protection is 0 and the
Venetian blind operating mode
is set.
82581443
J0082581443
8/11
24.03.2017
Page 9
eNet radio blinds actuator 1-gang mini
Priority, restraint 0...4
Basic setting: 2
Activate force operation blind
position
Recall forced operation slat
position
Deactivate force operation
blind position
Deacitvate forced operation
slat position
0 ... 100 %
Basic setting: 0 %
0 ... 100 %
Basic setting: 0 %
0 ... 100 %
Basic setting: 0 %
0 ... 100 %
Basic setting: 0 %
Specifies the priority for
recalling and removing a
scene of type Restraint for the
channel.
Defines the behaviour of the
output on activating the forced
operation.
Defines the slat position of the
output on activating forced
operation. Only visible when
the Venetian blind operating
mode is set.
Defines the behaviour of the
output on deactivating the
forced operation. Only visible
when the priority for the forced
operation is 0.
Defines the slat position of the
output on deactivating forced
operation. Only visible when
the priority for the forced
operation is 0 and the
Venetian blind operating mode
is set.
Priority, wind alarm 0...4
Basic setting: 3
Activate wind alarm blind
position
0 ... 100 %
Basic setting: 0 %
Recall wind alarm slat position 0 ... 100 %
Basic setting: 0 %
Deactivate wind alarm blind
position
Deacitvate wind alarm slat
position
0 ... 100 %
Basic setting: 0 %
0 ... 100 %
Basic setting: 0 %
Specifies the priority for
recalling and removing a
scene of type Wind alarm for
the channel.
Defines the behaviour of the
output on activating the wind
alarm.
Defines the slat position of the
output on activating the wind
alarm. Only visible when the
Venetian blind operating mode
is set.
Defines the behaviour of the
output on deactivating the
wind alarm. Only visible when
the priority for the wind alarm
is 0.
Defines the slat position of the
output on deactivating the
wind alarm. Only visible when
the priority for the wind alarm
is 0 and the Venetian blind
operating mode is set.
Priority, sun protection 0...4
Basic setting: 0
Activate sun protection blind
position
82581443
J0082581443
0 ... 100 %
Basic setting: 100 %
9/11
Specifies the priority for
recalling and removing a
scene of type Sun protection
for the channel.
Defines the behaviour of the
output on activating the sun
protection.
24.03.2017
Page 10
eNet radio blinds actuator 1-gang mini
Recall sun protection slat
position
Deactivate sun protection
blind position
Deacitvate sun protection slat
position
0 ... 100 %
Basic setting: 100 %
0 ... 100 %
Basic setting: 0 %
0 ... 100 %
Basic setting: 0 %
Priority, twilight 0...4
Basic setting: 0
Activate twilight blind position 0 ... 100 %
Basic setting: 100 %
Defines the slat position of the
output on activating the sun
protection. Only visible when
the Venetian blind operating
mode is set.
Defines the behaviour of the
output on deactivating the sun
protection. Only visible when
the priority for the sun
protection is 0.
Defines the slat position of the
output on deactivating the sun
protection. Only visible when
the priority for the sun
protection is 0 and the
Venetian blind operating mode
is set.
Specifies the priority for
recalling and removing a
scene of type Twilight for the
channel.
Defines the behaviour of the
output on activating the
twilight function.
Activate twilight slat position 0 ... 100 %
Basic setting: 100 %
Defines the slat position of the
output on activating the
twilight function. Only visible
when the Venetian blind
operating mode is set.
Deactivate twilight blind
position
0 ... 100 %
Basic setting: 0 %
Defines the behaviour of the
output on deactivating the
twilight function. Only visible
when the priority for the
twilight function is 0.
Deacitvate twilight slat position 0 ... 100 %
Basic setting: 0 %
Defines the slat position of the
output on deactivating the
twilight function. Only visible
when the priority for the
twilight function is 0 and the
Venetian blind operating mode
is set.
Information window
During channel selection in the Information window, the following settings can be made or
values displayed.
Display value Explanations
Position value, venetian blind The position value of the Venetian blind can
be changed.
Position value, slat The position value of the slat can be changed.
Restraint Display of forced position status.
Lock-out protection Display of the lock-out protection status
82581443
J0082581443
10/11
24.03.2017
Page 11
eNet radio blinds actuator 1-gang mini
Operating hours UP Display of the operating hours in the UP
direction since the last restart in the Settings
window.
Operating hours DOWN Display of the operating hours in the DOWN
direction since the last restart in the Settings
window.
6.3 Accessories
Mounting adapter for mini housing Art. No. FM-EBG
eNet server for rail mounting Art. No. ENET-SERVER
6.4 Conformity
Albrecht Jung GmbH & Co. KG hereby declares that the radio system type
Art. No. FMJ50700UP
corresponds to the directive 2014/53/EU. You can find the full article number on the device. The
complete text of the EU Declaration of Conformity is available under the Internet address:
www.jung.de/ce
6.5 Warranty
The warranty follows about the specialty store in between the legal framework as provided for
by law.
ALBRECHT JUNG GMBH & CO. KG
Volmestraße 1
58579 Schalksmühle
GERMANY
Telefon: +49 2355 806-0
Telefax: +49 2355 806-204
kundencenter@jung.de
www.jung.de
82581443
J0082581443
11/11
24.03.2017
Loading...