Jung FLW2200WW Operating Instructions Manual
Radio performance unit
Radio Management
Radio performance unit
Art. No. : FWL2200WW
Operating instructions
1 Safety instructions
Electrical equipment may only be installed and fitted by electrically skilled persons.
Danger of electric shock. Always disconnect before carrying out work on the devise or
load. In so doing, take all the circuit breakers into account, which support dangerous
voltages to the device and or load.
Danger of electric shock. Device is not suitable for disconnection from supply voltage.
Serious injuries, fire or property damage possible. Please read and follow manual fully.
The radio communication takes place via a non-exclusively available transmission path,
and is therefore not suitable for safety-related applications, such as emergency stop and
emergency call.
These instructions are an integral part of the product, and must remain with the end
customer.
2 Device components
Figure 1
(1) Radio power pack
(2) red LED
(3) green LED
(4) Housing lid
(5) Screws
3 Function
System information
By statute, the transmitting power, the reception characteristics and the antenna cannot be
changed.
The range of a radio system from the transmitter to the receiver depends on various
circumstances.
1/9
32529813
J0082529813
02.11.2016
The range of the system can be optimised by selecting the optimal installation location, taking
into account the structural circumstances.
Figure 2: Reduced range due to structural obstacles
Intended use
- Radio-controlled switching of electrical loads for the duration of a settable time.
- Operation with suitable radio motion detectors, radio transmitters and installation buttons
as an extension
- Surface-mounted
Product characteristics
- Device responds to radio telegrams from radio motion detectors
- Operation possible via radio manual and wall transmitters
- Brightness threshold settable
- Switch-on time settable
- Switch-on for 2 hours and switch-off for 2 hours possible
- Can be integrated into All On and All Off
i Combination with radio presence detector possible, but without light control
4 Operation
Normal operation
In normal operation the power pack switches the load on for the set switch-on time when a
taught radio motion detector telegram is received. Switching-on takes place depending on the
brightness.
Taught radio hand transmitters, radio wall transmitter or installation buttons, NC contacts,
switch the load on the power pack independently of the brightness.
i Switching on the mains voltage of the power pack always triggers a switching operation on
the power pack, regardless of the brightness setting.
The red LED (2) indicates the reception of a radio telegram and the green LED (3) indicates the
state of the switching output, see the next table.
red LED green LED
Receives radio telegram 1 second to No change
Battery of the motion detector
weak
on No change
Load is switched on No change on
Programming mode active flashes off
Transmitter taught on on
2/9
32529813
J0082529813
02.11.2016
Radio Management
Radio performance unit
Transmitter deleted on off
Switch-on for set switch-on time
o Operation with installation button: press push-button one time briefly.
Or:
o Operation with radio transmitter: Press taught channel button /\ less than 1 second.
The load is switched on for the preset switch-on time independently of the brightness.
Motion telegrams of a taught radio motion detector or radio presence detector are detected
and evaluated.
Switch on for 2 hours.
o Operation with installation button: press push-button twice briefly.
Or:
o Operation with radio transmitter: Press taught channel button /\ longer than 1 second.
The load is switched on for approx. 2 hours independently of the brightness. After that the
device switches back to normal operation.
Switch off the load
o Press the taught channel button \/ of a radio transmitter for less than 1 second.
Load switches off and device changes over to normal operation.
Switch-off for 2 hours
o Operation with installation button: press push-button three times briefly.
Or:
o Operation with radio transmitter: Press taught channel button \/ longer than 1 second.
The load is switched off continuously for approx. 2 hours. After that the device switches
back to normal operation.
All on
o Press the all on button of a taught radio transmitter.
All of the connected loads are switched on for the set switch-on time.
All off
o Press the all off button of a taught radio transmitter.
All of the connected loads are switched off.
5 Information for electrically skilled persons
5.1 Fitting and electrical connection
DANGER!
Electrical shock when live parts are touched.
Electrical shocks can be fatal.
Before working on the device, disconnect the power supply and cover up live
parts in the working environment.
Installing the power pack
Maintain a distance of at least 1 m between the radio transmitter and the power pack.
3/9
32529813
J0082529813
02.11.2016
Radio Management
Radio performance unit
Loading...