Light Management Touch sensor module AC/DC 24 V
Ref.-no.: 2224 TSM,
2236 TSM, 2248 TSM
Operating Instructions
Touch sensor module AC/DC 24 V
2-channel, 3-channel, 4-channel
1. Safety warnings
Attention: Electrical equipment must be installed and fitted by
qualified electricians only.
Failure to observe any of the installation instructions may cause
damage to the device and result in fire or other hazards.
The sensor is a safety class III device. Connect only SELV circuits of
24 V to the device (no mains potential!).
2. Function
Touch sensors intended for connection to the 8- channel relay station,
Art. no. RS8 REG HE or other control systems. Each sensor is equipped
with two red LEDs for status indication purposes. Connection to the
device is made at the back by means of a terminal block. The touch
sensor rockers are “divided” into an upper and a lower half and generally
control two consumers (or other functions). To actuate the rockers, the
device must be equipped with the corresponding touch sensor module
covers (must be ordered separately):
Stand: Jan-09 825 587 03
Light Management Touch sensor module AC/DC 24 V
Ref.-no.: 2224 TSM,
2236 TSM, 2248 TSM
2-channel 2224 TSM 2 x FD..902 TSA..
3-channel 2236 TSM 1 x FD..902 TSA..
and 2 x FD..904 TSA..
4-channel 2248 TSM 4 x FD..904 TSA..
3. Connection
Sensor
terminal
1
2
3
4
5
6
7
8
Sensor outputs and LED inputs (FIG. B)
Assigned to following rocker:
4-ch. 3-ch. 2-ch.
1 top 1 top
1 bottom 1 bottom
2 top 2 top
2 bottom 2 bottom
3 top
3 bottom
4 top
4 bottom
3 top 2 top
3 bottom 2 bottom
1 top
1 bottom
LED-
terminal
1
2
3
4
5
6
7
8
2
Light Management Touch sensor module AC/DC 24 V
Ref.-no.: 2224 TSM,
2236 TSM, 2248 TSM
4. Installation
• Fit the supporting ring (1) in the correct position on a flush-mounting
box (observe the TOP marking).
• Place the decorative frame (2) on the supporting ring.
• Connect the touch sensor module (3) to the 8- channel relay station
and place it on the supporting ring (see table above).
• Schließen Sie das Tastsensor-Modul (3) an die Relais-Statio n
8fach an und stecken Sie es auf den Tragring (siehe Tabelle oben).
• Fasten the touch sensor module with the plastic screws supplied (4)
on the supporting ring. The screws are intended as a protection
against removal or theft. Tighten the plastic screws only lightly !
• Fit the covers (5): Place the covers one by one on the touch sensor
module. The arrangement of the covers is shown in FIG A. Make
sure the cover fits properly (observe the marking TOP on the
inside) and snap it onto the device by a brief press.
Fig. C
4.1. Label covers
Fig. D
3
Light Management Touch sensor module AC/DC 24 V
Ref.-no.: 2224 TSM,
2236 TSM, 2248 TSM
The covers with Art. no. FD..90x TSA NA.. can be equipped with labels.
Commercial-grade transparencies can be inscribed with the help of the
JUNG labelling software and inserted as labels into the covers. The
JUNG labelling software is available in the Internet under the following
address: www.jung-beschriftungsservice.de. Fit the label covers as
shown in FIG. D.
5. Technical data
Rated voltage sensor/LED : AC/DC 24 V SELV
Current load of sensor : max. 20 mA per sensor
LED current : approx. 1 mA per LED
Connection : 2 x terminal block 9-pole
0.25...0.8 mm² single wire
Power consumption : max. 0.2 W
(all LEDs on)
Safety class : III
Ambient temperature : -5 °C ... +45 °C
Storage / transport temp. : -25 °C ... +70 °C
Technical specifications subject to change.
6. Guarantee
Our products are under guarantee within the scope of the statutory
provisions.
Please return the unit postage paid to our central service
department giving a brief description of the fault:
ALBRECHT JUNG GMBH & CO. KG
Service-Center
Kupferstr. 17-19
D-44532 Lünen
Service-Line: +(49) 23 55 . 80 65 51
Telefax: +(49) 23 55 . 80 61 65
E-Mail: mail.vka@jung.de
General equipment
Service-Line: +(49) 23 55 . 80 65 55
Telefax: +(49) 23 55 . 80 62 55
E-Mail: mail.vkm@jung.de
KNX equipment
Service-Line: +(49) 23 55 . 80 65 56
Telefax: +(49) 23 55 . 80 62 55
E-Mail: mail.vkm@jung.de
The
authorities and does not include any warranty of any properties.
-Sign is a free trade sign addressed exclusively to the
4
Loading...